Effect of RGD peptide coating of titanium implants on periimplant bone formation in the alveolar crest. An experimental pilot study in dogs

Black phosphorus-incorporated novel Ti-12Mo-10Zr implant for multimodal treatment of osteosarcoma

The repair and reconstruction of large bone defects after bone tumor resection is still a great clinical challenge. At present, orthopedic implant reconstruction is the mainstream treatment for repairing bone defects. However, according to clinical feedback, local tumor recurrence and nonunion of bone graft are common reasons leading to the failure of bone defect repair and reconstruction after bone tumor resection, which seriously threaten the physical and mental health of patients. On this basis, here the self-developed low modulus Ti-12Mo-10Zr alloy (TMZ) was chosen as substrate material. To improve its biological activity and osteointegration, calcium, oxygen, and phosphorus co-doped microporous coating was prepared on TMZ alloy by microarc oxidation (MAO). Then, black phosphorus (BP) nanosheets were incorporated onto MAO treated TMZ alloy to obtain multifunctional composites. The obtained BP-MAO-TMZ implant exhibited excellent photothermal effects and effective ablation of osteosarcoma cancer cells under the irradiation of 808 nm near infrared laser, while no photothermal or therapeutic effects were observed for TMZ alloy. Meanwhile, the structure/component bionic coating obtained after MAO treatment as well as the P-driven in situ biomineralization performance after incorporation of BP nanosheets endowed BP-MAO-TMZ implant with synergistic promoting effect on MC3T3-E1 osteoblasts' activity, proliferation and differentiation ability. This study is expected to provide effective clinical solutions for problems of difficult bone regeneration and tumor recurrence after tumor resection in patients with bone tumors and to solve a series of medical problems such as poor prognosis and poor postoperative quality of patients life with malignant bone tumors.

Comparison of Clinical Outcomes of Platelet-Rich Plasma for Epicondylitis, Elbow: Simultaneous Lateral and Medial Versus Lateral Versus Medial

OBJECTIVE

Lateral and medial epicondylitis are relatively common diseases, but they do not improve quickly and are known to reduce patients' quality of life. Much research has been done on Platelet-Rich Plasma (PRP) as a treatment for lateral epicondylitis, but research on medial epicondylitis is lacking. The purpose of this study is to compare: (i) the pain intensity; and (ii) the functional outcome between the simultaneous treatment of medial and lateral epicondylitis and the treatment of only lateral or medial epicondylitis using PRP.

METHODS

In this retrospective study, 209 patients treated with PRP on epicondylitis between March 2018 and December 2021 were enrolled. Simultaneous treatment was underwent 68 patients (group I). Seventy patients were treated for lateral epicondylitis (group II). The remaining 71 patients were treated for medial epicondylitis (group III). The visual analogue scale for pain (VAS) and the Mayo elbow performance score (MEPS) were evaluated for clinical outcomes at the initial visit and 6 months after injection.

RESULTS

VAS for pain and MEPS showed significant improvement in all three groups compared to before treatment. There was no significant difference between three groups on -ΔVAS (P > 0.05). However, in case of ΔMEPS, group III showed significantly lower compared to groups II and III (P < 0.05). No patients showed worsening of symptoms or complications during the treatment.

CONCLUSION

PRP injection for the patient with elbow medial and lateral epicondylitis can be treated effectively simultaneously in terms of pain. From a functional point of view, the effect of simultaneous treatment may be lessened than in the case of only lateral and medial treatment.

Collagen-Based Osteogenic Nanocoating of Microrough Titanium Surfaces

The aim of the present study was to develop a collagen/heparin-based multilayer coating on titanium surfaces for retarded release of recombinant human bone morphogenic protein 2 (rhBMP2) to enhance the osteogenic activity of implant surfaces. Polyelectrolyte multilayer (PEM) coatings were constructed on sandblasted/acid-etched surfaces of titanium discs using heparin and collagen. PEM films of ten double layers were produced and overlayed with 200 µL of a rhBMP2 solution containing 15 µg rhBMP2. Subsequently, cross-linking of heparin molecules was performed using EDC/NHS chemistry to immobilize the incorporated rhBMP2. Release characteristics for 3 weeks, induction of Alkaline Phosphatase (ALP) in C2C12 cells and proliferation of human mesenchymal stem cells (hMSCs) were evaluated to analyze the osteogenic capacity of the surface. The coating incorporated 10.5 µg rhBMP2 on average per disc and did not change the surface morphology. The release profile showed a delivery of 14.5% of the incorporated growth factor during the first 24 h with a decline towards the end of the observation period with a total release of 31.3%. Cross-linking reduced the release with an almost complete suppression at 100% cross-linking. Alkaline Phosphatase was significantly increased on day 1 and day 21, indicating that the growth factor bound in the coating remains active and available after 3 weeks. Proliferation of hMSCs was significantly enhanced by the non-cross-linked PEM coating. Nanocoating using collagen/heparin-based PEMs can incorporate clinically relevant amounts of rhBMP2 on titanium surfaces with a retarded release and a sustained enhancement of osteogenic activity without changing the surface morphology.

Preparation of chitosan-tannic acid coating and its anti-osteoclast and antibacterial activities in titanium implants

INTRODUCTION

Bacterial infection and aseptic loosening caused by bone resorption at the implant interface are major clinical complications during bone defect implantation surgery, and surface modification of the implant to address the aforementioned problems has long been a research focus.

MATERIALS AND METHODS

In this paper, a chitosan (CTS)-tannic acid (TA) colloid coating with a negative charge and excellent hydrophilicity was prepared on a Ti6Al4V (TC4) surface using a layer-by-layer assembly method. The physical properties, anti-osteoclast activity, and antimicrobial activity of the coatings were investigated.

RESULTS

The findings showed that when the pH value was 5 and the ratio of CTS:TA was 0.8, the carrying rate of TA was the best. Furthermore, the CTS-TA coating had no cytotoxicity on the morphology and proliferation of BMSCs cells and effectively inhibited the differentiation of RAW264.7 cells into osteoclasts and the proliferation of Staphylococcus aureus and Escherichia coli. With the increase in the immersion time of TC4 in CTS-TA colloid solution, the inhibitory effects will also enhance.

CONCLUSION

Therefore, the preparation of the CTS-TA coating provides a revolutionary technique for implant surface modification to avoid postoperative bacterial infection and aseptic loosening.

The Impact of Dental Implant Surface Modifications on Osseointegration and Biofilm Formation

Implant surface design has evolved to meet oral rehabilitation challenges in both healthy and compromised bone. For example, to conquer the most common dental implant-related complications, peri-implantitis, and subsequent implant loss, implant surfaces have been modified to introduce desired properties to a dental implant and thus increase the implant success rate and expand their indications. Until now, a diversity of implant surface modifications, including different physical, chemical, and biological techniques, have been applied to a broad range of materials, such as titanium, zirconia, and polyether ether ketone, to achieve these goals. Ideal modifications enhance the interaction between the implant's surface and its surrounding bone which will facilitate osseointegration while minimizing the bacterial colonization to reduce the risk of biofilm formation. This review article aims to comprehensively discuss currently available implant surface modifications commonly used in implantology in terms of their impact on osseointegration and biofilm formation, which is critical for clinicians to choose the most suitable materials to improve the success and survival of implantation.

Bone formation potential of collagen type I-based recombinant peptide particles in rat calvaria defects

Introduction

This study aimed to examine the bone-forming ability of medium-cross-linked recombinant collagen peptide (mRCP) particles developedbased on human collagen type I, contains an arginyl-glycyl-aspartic acid-rich motif, fabricated as bone filling material, compared to that of the autologous bone graft.

Methods

Calvarial bone defects were created in immunodeficient rats though a surgical procedure. The rats were divided into 2 groups: mRCP graft and tibia bone graft (bone graft). The bone formation potential of mRCP was evaluated by micro-computed tomography and hematoxylin-eosin staining at 1, 2, 3, and 4 weeks after surgery, and the data were analyzed and compared to those of the bone graft.

Results

The axial volume-rendered images demonstrated considerable bony bridging with the mRCP graft, but there was no significant difference in the bone volume and bone mineral density between the mRCP graft and bone graft at 4 weeks. The peripheral new bone density was significantly higher than the central new bone density and the bottom side score was significantly higher than the top side score at early stage in the regenerated bone within the bone defects.

Conclusion

These results indicate that mRCP has a high potential of recruiting osteogenic cells, comparable to that of autologous bone chips.

•

Bone formation potential of mRCP were comparable to that of autogenous bone.

•

mRCP particles exhibit high new bone formation potential in the calvaria defect.

•

Bone bridging was observed over the entire defect in mRCP graft at 4 weeks.

•

mRCP has a high potential of recruiting osteogenic cells comparable to bone graft.

Harnessing biomolecules for bioinspired dental biomaterials

Dental clinicians have relied for centuries on traditional dental materials (polymers, ceramics, metals, and composites) to restore oral health and function to patients. Clinical outcomes for many crucial dental therapies remain poor despite many decades of intense research on these materials. Recent attention has been paid to biomolecules as a chassis for engineered preventive, restorative, and regenerative approaches in dentistry. Indeed, biomolecules represent a uniquely versatile and precise tool to enable the design and development of bioinspired multifunctional dental materials to spur advancements in dentistry. In this review, we survey the range of biomolecules that have been used across dental biomaterials. Our particular focus is on the key biological activity imparted by each biomolecule toward prevention of dental and oral diseases as well as restoration of oral health. Additional emphasis is placed on the structure-function relationships between biomolecules and their biological activity, the unique challenges of each clinical condition, limitations of conventional therapies, and the advantages of each class of biomolecule for said challenge. Biomaterials for bone regeneration are not reviewed as numerous existing reviews on the topic have been recently published. We conclude our narrative review with an outlook on the future of biomolecules in dental biomaterials and potential avenues of innovation for biomaterial-based patient oral care.

Keratinocyte-Specific Peptide-Based Surfaces for Hemidesmosome Upregulation and Prevention of Bacterial Colonization

Percutaneous devices like orthopedic prosthetic implants for amputees, catheters, and dental implants suffer from high infection rates. A critical aspect mediating peri-implant infection of dental implants is the lack of a structural barrier between the soft tissue and the implant surface which could impede bacteria access and colonization of exposed implant surfaces. Parafunctional soft tissue regeneration around dental implants is marked by a lack of hemidesmosome formation and thereby weakened mechanical attachment. In response to this healthcare burden, a simultaneously hemidesmosome-inducing, antimicrobial, multifunctional implant surface was engineered. A designer antimicrobial peptide, GL13K, and a laminin-derived peptide, LamLG3, were coimmobilized with two different surface fractional areas. The coimmobilized peptide surfaces showed antibiofilm activity against Streptococcus gordonii while enhancing proliferation, hemidesmosome formation, and mechanical attachment of orally derived keratinocytes. Notably, the coatings demonstrated specific activation of keratinocytes: the coatings showed no effects on gingival fibroblasts which are known to impede the quality of soft tissue attachment to dental implants. These coatings demonstrated stability and retained activity against mechanical and thermochemical challenges, suggesting their intraoral durability. Overall, these multifunctional surfaces may be able to reduce peri-implantitis rates and enhance the success rates of all percutaneous devices via strong antimicrobial activity and enhanced soft tissue attachment to implants.

Bioinspired Fabrication of Calcium-Doped TiP Coating with Nanofibrous Microstructure to Accelerate Osseointegration

Bioinspired by the morphology of osteoclast-resorbed bone surfaces, we prepared a calcium-doped titanium phosphate (Ca-TiP) coating, which consists of a nanofibrous network, on titanium (Ti) substrate via a simple two-step hydrothermal method, trying to mimic natural bone compositionally and microstructurally. The in vitro studies show that the Ca-TiP coating with synergistic features of nanofibrous biomimetic topography and surface chemistry could elicit intensively osteogenic behavior and responses including enhanced cell adhesion, spreading, and proliferation as well as alkaline phosphatase (ALP) activity and up-regulated expression of bone-related genes, which inevitably benefit the formation of new bone and the quality of osseointegration. When the two control groups are compared in vivo, the significantly improved new bone formation in the early stage and the much stronger interfacial bonding with the surrounding bone for Ca-TiP coating suggest that Ca-TiP coating modified Ti implants hold great potential for orthopedic and dental applications.

Biocompatible Organic Coatings Based on Bisphosphonic Acid RGD-Derivatives for PEO-Modified Titanium Implants

Currently, significant attention is attracted to the problem of the development of the specific architecture and composition of the surface layer in order to control the biocompatibility of implants made of titanium and its alloys. The titanium surface properties can be tuned both by creating an inorganic sublayer with the desired morphology and by organic top coating contributing to bioactivity. In this work, we developed a composite biologically active coatings based on hybrid molecules obtained by chemical cross-linking of amino acid bisphosphonates with a linear tripeptide RGD, in combination with inorganic porous sublayer created on titanium by plasma electrolytic oxidation (PEO). After the addition of organic molecules, the PEO coated surface gets nobler, but corrosion currents increase. In vitro studies on proliferation and viability of fibroblasts, mesenchymal stem cells and osteoblast-like cells showed the significant dependence of the molecule bioactivity on the structure of bisphosphonate anchor and the linker. Several RGD-modified bisphosphonates of β-alanine, γ-aminobutyric and ε-aminocaproic acids with BMPS or SMCC linkers can be recommended as promising candidates for further in vivo research.

Repeatedly Applied Peptide Film Kills Bacteria on Dental Implants

The rising use of titanium dental implants has increased the prevalence of peri-implant disease that shortens their useful life. A growing view of peri-implant disease suggests that plaque accumulation and microbiome dysbiogenesis trigger a host immune inflammatory response that destroys soft and hard tissues supporting the implant. The incidence of peri-implant disease is difficult to estimate, but with over 3 million implants placed in the USA alone, and the market growing by 500,000 implants/year, such extensive use demands additional interceptive approaches. We report a water-based, nonsur-gical approach to address peri-implant disease using a bifunctional peptide film, which can be applied during initial implant placement and later reapplied to existing implants to reduce bacterial growth. Bifunctional peptides are based upon a titanium binding peptide (TiBP) optimally linked by a spacer peptide to an antimicrobial peptide (AMP). We show herein that dental implant surfaces covered with a bifunctional peptide film kill bacteria. Further, using a simple protocol for cleaning implant surfaces fouled by bacteria, the surface can be effectively recoated with TiBP-AMP to regain an antimicrobial state. Fouling, cleansing, and rebinding was confirmed for up to four cycles with minimal loss of binding efficacy. After fouling, rebinding with a water-based peptide film extends control over the oral microbiome composition, providing a novel nonsurgical treatment for dental implants.

Gelatin Hydrogel Combined with Polydopamine Coating to Enhance Tissue Integration of Medical Implants

Soft tissue integration of medical implants is important to prevent bacterial infection and implant failure. A bioadhesive that forms firm binding between the implant and the surrounding tissue and facilitates the wound-healing process will be a great tool to establish the desired tissue-implant integration. In this project, we introduce a novel method that can be used to enhance integration between any implant material and any tissue using an enzyme-crosslinked gelatin hydrogel combined with polydopamine (PDA) coating. PDA coating was shown to enhance the binding between the gelatin hydrogel and three model implant materials - aluminum, poly(methyl methacrylate) (PMMA) and titanium. When combined with the gelatin hydrogel, pig cornea tissue adhered more strongly to the PDA coated surfaces than to the uncoated surfaces. The enzyme-crosslinked gelatin hydrogel was non-cytotoxic to human dermal fibroblasts and it also allowed the cells to adhere and proliferate. Altogether, the results indicate that the combination of PDA coating with gelatin hydrogel can be used to enhance the integration of various medical implants.

Effect of calcium ions on peptide adsorption at the aqueous rutile titania (110) interface

How the presence of Ca²⁺ ions at the aqueous TiO₂ interface influences the binding modes of two experimentally identified titania-binding peptides, Ti-1 and Ti-2, is investigated using replica exchange with solute tempering molecular dynamics simulations. The findings are compared with available experimental data, and the results are contrasted with those obtained under NaCl solution conditions. For Ti-1, Ca²⁺ ions enhance the adsorption of the negatively charged Asp8 residue in this sequence to the negatively charged surface, via Asp–Ca²⁺–TiO₂ bridging. This appears to generate a nonlocal impact on the adsorption of Lys12 in Ti-1, which then pins the peptide to the surface via direct surface contact. For Ti-2, fewer residues were predicted to adsorb directly to the surface in CaCl₂, compared with predictions made for NaCl solution, possibly due to competition between the other peptide residues and Ca²⁺ ions to adsorb to the surface. This reduction in direct surface contact gives rise to a more extensive solvent-mediated contact for Ti-2. In general, the presence of Ca²⁺ ions resulted in a loss of conformational diversity of the surface-adsorbed conformational ensembles of these peptides, compared to counterpart data predicted for NaCl solution. The findings provide initial insights into how peptide–TiO₂ interactions might be tuned at the molecular level via modification of the salt composition of the liquid medium.

Synergistic Effect of Cold Plasma Treatment and RGD Peptide Coating on Cell Proliferation over Titanium Surfaces

The aim of this study was to investigate the synergistic effect of cold atmospheric plasma (CAP) treatment and RGD peptide coating for enhancing cellular attachment and proliferation over titanium (Ti) surfaces. The surface structure of CAP-treated and RGD peptide-coated Ti discs were characterized by contact angle goniometer and atomic force microscopy. The effect of such surface modification on human bone marrow derived mesenchymal stem cells (hMSCs) adhesion and proliferation was assessed by cell proliferation and DNA content assays. Besides, hMSCs' adhesion and morphology on surface modified Ti discs were observed via fluorescent and scanning electron microscopy. RGD peptide coating following CAP treatment significantly enhanced cellular adhesion and proliferation among untreated, CAP-treated and RGD peptide-coated Ti discs. The treatment of Ti surfaces with CAP may contribute to improved RGD peptide coating, which enables increased cellular integrations with the Ti surfaces.

Osseous response on linear and cyclic RGD-peptides immobilized on titanium surfaces in vitro and in vivo

Biomimetic surface modifications of titanium (Ti) implants using the Arg-Gly-Asp-sequence (RGD) are promising to accelerate bone healing in cases of medical implants. Therefore, we compared the impact of linear and cyclic RGD (l- and c-RGD) covalently coupled onto Ti surfaces on the osseous response in vitro and in vivo. In vitro, osteoblasts' behavior on different surfaces (unmodified, amino-silanized [APTES], l- and c-RGD) was analysed regarding adhesion (fluorescence microscopy), proliferation (resazurin stain) and differentiation (reverse transcription polymerase chain reaction on alkaline phosphatase and osteocalcin). In vivo, osteosynthesis screws (unmodified n = 8, l-RGD n = 8, c-RGD n = 8) were inserted into the proximal tibiae of 12 rabbits and evaluated for bone growth parameters (bone implant contact [%] and vertical bone apposition [VBA;%]) at 3 and 6 weeks. In vitro, c- as well as l-RGD surfaces stimulated osteoblasts' adherence, proliferation and differentiation in a similar manner, with only subtle evidence of superiority of the c-RGD modifications. In vivo, c-RGD-modifications led to a significantly increased VBA after 3 and 6 weeks. Thus, coating with c-RGD appears to play an important role influencing osteoblasts' behaviour in vitro but especially in vivo. These findings can be applied prospectively to implantable biomaterials with hypothetically improved survival and success rates. © 2017 Wiley Periodicals Inc. J Biomed Mater Res Part A: 106A: 419-427, 2018.

Graphene as an Enabling Strategy for Dental Implant and Tissue Regeneration

Graphene-based approaches have been influential in the design and manipulation of dental implants and tissue regeneration to overcome the problems associated with traditional titanium-based dental implants, such as their low biological affinity. Here, we describe the current progress of graphene-based platforms, which have contributed to major advances for improving cellular functions in in vitro and in vivo applications of dental implants. We also present opinions on the principal challenges and future prospects for new graphene-based platforms for the development of advanced graphene dental implants and tissue regeneration.

Peptide coating applied on the spot improves osseointegration of titanium implants

On the spot osseointegrating peptide coating applicable to any size and shape of titanium bone implants.

Surface Functionalization of Orthopedic Titanium Implants with Bone Sialoprotein

Orthopedic implant failure due to aseptic loosening and mechanical instability remains a major problem in total joint replacement. Improving osseointegration at the bone-implant interface may reduce micromotion and loosening. Bone sialoprotein (BSP) has been shown to enhance bone formation when coated onto titanium femoral implants and in rat calvarial defect models. However, the most appropriate method of BSP coating, the necessary level of BSP coating, and the effect of BSP coating on cell behavior remain largely unknown. In this study, BSP was covalently coupled to titanium surfaces via an aminosilane linker (APTES), and its properties were compared to BSP applied to titanium via physisorption and untreated titanium. Cell functions were examined using primary human osteoblasts (hOBs) and L929 mouse fibroblasts. Gene expression of specific bone turnover markers at the RNA level was detected at different intervals. Cell adhesion to titanium surfaces treated with BSP via physisorption was not significantly different from that of untreated titanium at any time point, whereas BSP application via covalent coupling caused reduced cell adhesion during the first few hours in culture. Cell migration was increased on titanium disks that were treated with higher concentrations of BSP solution, independent of the coating method. During the early phases of hOB proliferation, a suppressive effect of BSP was observed independent of its concentration, particularly when BSP was applied to the titanium surface via physisorption. Although alkaline phosphatase activity was reduced in the BSP-coated titanium groups after 4 days in culture, increased calcium deposition was observed after 21 days. In particular, the gene expression level of RUNX2 was upregulated by BSP. The increase in calcium deposition and the stimulation of cell differentiation induced by BSP highlight its potential as a surface modifier that could enhance the osseointegration of orthopedic implants. Both physisorption and covalent coupling of BSP are similarly effective, feasible methods, although a higher BSP concentration is recommended.

Engineered protein coatings to improve the osseointegration of dental and orthopaedic implants

Here we present the design of an engineered, elastin-like protein (ELP) that is chemically modified to enable stable coatings on the surfaces of titanium-based dental and orthopaedic implants by novel photocrosslinking and solution processing steps. The ELP includes an extended RGD sequence to confer bio-signaling and an elastin-like sequence for mechanical stability. ELP thin films were fabricated on cp-Ti and Ti6Al4V surfaces using scalable spin and dip coating processes with photoactive covalent crosslinking through a carbene insertion mechanism. The coatings withstood procedures mimicking dental screw and hip replacement stem implantations, a key metric for clinical translation. They promoted rapid adhesion of MG63 osteoblast-like cells, with over 80% adhesion after 24 h, compared to 38% adhesion on uncoated Ti6Al4V. MG63 cells produced significantly more mineralization on ELP coatings compared to uncoated Ti6Al4V. Human bone marrow mesenchymal stem cells (hMSCs) had an earlier increase in alkaline phosphatase activity, indicating more rapid osteogenic differentiation and mineral deposition on adhesive ELP coatings. Rat tibia and femur in vivo studies demonstrated that cell-adhesive ELP-coated implants increased bone-implant contact area and interfacial strength after one week. These results suggest that ELP coatings withstand surgical implantation and promote rapid osseointegration, enabling earlier implant loading and potentially preventing micromotion that leads to aseptic loosening and premature implant failure.

Biomaterial strategies for engineering implants for enhanced osseointegration and bone repair

Bone tissue has a remarkable ability to regenerate and heal itself. However, large bone defects and complex fractures still present a significant challenge to the medical community. Current treatments center on metal implants for structural and mechanical support and auto- or allo-grafts to substitute long bone defects. Metal implants are associated with several complications such as implant loosening and infections. Bone grafts suffer from donor site morbidity, reduced bioactivity, and risk of pathogen transmission. Surgical implants can be modified to provide vital biological cues, growth factors and cells in order to improve osseointegration and repair of bone defects. Here we review strategies and technologies to engineer metal surfaces to promote osseointegration with the host tissue. We also discuss strategies for modifying implants for cell adhesion and bone growth via integrin signaling and growth factor and cytokine delivery for bone defect repair.

The Effects of TiO2 Nanodot Films with RGD Immobilization on Light-Induced Cell Sheet Technology

Cell sheet technology is a new strategy in tissue engineering which could be possible to implant into the body without a scaffold. In order to get an integrated cell sheet, a light-induced method via UV365 is used for cell sheet detachment from culture dishes. In this study, we investigated the possibility of cell detachment and growth efficiency on TiO₂ nanodot films with RGD immobilization on light-induced cell sheet technology. Mouse calvaria-derived, preosteoblastic (MC3T3-E1) cells were cultured on TiO₂ nanodot films with (TR) or without (TN) RGD immobilization. After cells were cultured with or without 5.5 mW/cm² UV365 illumination, cell morphology, cell viability, osteogenesis related RNA and protein expression, and cell detachment ability were compared, respectively. Light-induced cell detachment was possible when cells were cultured on TR samples. Also, cells cultured on TR samples showed better cell viability, alongside higher protein and RNA expression than on TN samples. This study provides a new biomaterial for light-induced cell/cell sheet harvesting.

Calcium phosphate nanocoatings and nanocomposites, part I: recent developments and advancements in tissue engineering and bioimaging

A number of materials have been applied as implant coatings and as tissue regeneration materials. Calcium phosphate holds a special consideration, due to its chemical similarity to human bone and, most importantly, its dissolution characteristics, which allow for bone growth and regeneration. The applications of molecular and nanoscale-based biological materials have been and will continue to play an ever increasing role in enhancing and improving the osseointegration of dental and orthopedic implants. More recently, extensive research efforts have been focused on the development and applications of fluorescent nanoparticles and nanocoatings for in vivo imaging and diagnostics as well as devising methods of adding luminescent or fluorescent capabilities to enhance the in vivo functionality of calcium phosphate-based biomedical materials.

Simple coating with fibronectin fragment enhances stainless steel screw osseointegration in healthy and osteoporotic rats

Metal implants are widely used to provide structural support and stability in current surgical treatments for bone fractures, spinal fusions, and joint arthroplasties as well as craniofacial and dental applications. Early implant-bone mechanical fixation is an important requirement for the successful performance of such implants. However, adequate osseointegration has been difficult to achieve especially in challenging disease states like osteoporosis due to reduced bone mass and strength. Here, we present a simple coating strategy based on passive adsorption of FN7-10, a recombinant fragment of human fibronectin encompassing the major cell adhesive, integrin-binding site, onto 316-grade stainless steel (SS). FN7-10 coating on SS surfaces promoted α5β1 integrin-dependent adhesion and osteogenic differentiation of human mesenchymal stem cells. FN7-10-coated SS screws increased bone-implant mechanical fixation compared to uncoated screws by 30% and 45% at 1 and 3 months, respectively, in healthy rats. Importantly, FN7-10 coating significantly enhanced bone-screw fixation by 57% and 32% at 1 and 3 months, respectively, and bone-implant ingrowth by 30% at 3 months compared to uncoated screws in osteoporotic rats. These coatings are easy to apply intra-operatively, even to implants with complex geometries and structures, facilitating the potential for rapid translation to clinical settings.

Hydroxyapatite and silk combination-coated dental implants result in superior bone formation in the peri-implant area compared with hydroxyapatite and collagen combination-coated implants

PURPOSE

The objective of this study was to compare bone formation after installation of uncoated (UC), hydroxyapatite-coated (HA), collagen plus HA-coated (CH), and silk plus HA-coated (SH) implants.

MATERIALS AND METHODS

Implants in the UC group had acid-etched surfaces. Surface coating was applied using the aerosol deposition method. Cellular responses on the coated surfaces were examined with scanning electron microscopy. Cellular responses to the surfaces were studied with the corresponding coated discs and MG63 cells. Subsequently, 3-(4, 5-dimethylthiazole-2-yl)-2,5-diphenyltetrazolium bromide (MTT) and alkaline phosphatase (ALP) assays were performed. Peri-implant bone formation was evaluated with the rabbit tibia model. Twenty-four implants from each group were installed. The animals were sacrificed 6 weeks after implant installation. Peri-implant bone formation and implant-to-bone contact were measured in histologic sections. Significance of differences across groups was evaluated using analysis of variance.

RESULTS

Scanning electron microscopic images showed that the CH and SH groups exhibited cells that appeared more spread out than those in the other groups. The SH group exhibited the highest value in the MTT assay. The CH group exhibited the highest level of ALP activity. Comparisons of these modifications with the acid-etched surfaces showed that the CH and SH groups displayed significantly greater peri-implant bone formation (P < .001).

CONCLUSION

The SH group displayed significantly greater new bone formation and bone-to-implant contact than did the other groups.

Engineering biomolecular microenvironments for cell instructive biomaterials

Engineered cell instructive microenvironments with the ability to stimulate specific cellular responses are a topic of high interest in the fabrication and development of biomaterials for application in tissue engineering. Cells are inherently sensitive to the in vivo microenvironment that is often designed as the cell "niche." The cell "niche" comprising the extracellular matrix and adjacent cells, influences not only cell architecture and mechanics, but also cell polarity and function. Extensive research has been performed to establish new tools to fabricate biomimetic advanced materials for tissue engineering that incorporate structural, mechanical, and biochemical signals that interact with cells in a controlled manner and to recapitulate the in vivo dynamic microenvironment. Bioactive tunable microenvironments using micro and nanofabrication have been successfully developed and proven to be extremely powerful to control intracellular signaling and cell function. This Review is focused in the assortment of biochemical signals that have been explored to fabricate bioactive cell microenvironments and the main technologies and chemical strategies to encode them in engineered biomaterials with biological information.

Hydroxyapatite and collagen combination-coated dental implants display better bone formation in the peri-implant area than the same combination plus bone morphogenetic protein-2-coated implants, hydroxyapatite only coated implants, and uncoated implants

PURPOSE

The objective of this study was to compare peri-implant bone formation among uncoated (UC), hydroxyapatite (HA), collagen plus HA (CH), and collagen, HA, plus bone morphogenetic protein-2 (BMP-2) implant groups.

MATERIALS AND METHODS

Implants in the UC group had acid-etched surfaces. The surface coating was applied using the aerosol deposition method. The coated surfaces were examined by scanning electron microscopy, x-ray diffraction (XRD), and Fourier-transformed infrared absorption analysis. Subsequently, 6 implants from each group (total, 24 implants) were installed in the tibias of rabbits. The animals were sacrificed at 6 weeks after implant installation. Peri-implant bone formation and bone-to-implant contact (BIC) were measured in histologic sections. Significant differences among groups were evaluated using analysis of variance.

RESULTS

Based on the measured XRD patterns, there was a characteristic HA phase (International Centre for Diffraction Data [ICDD], 086-0740) coated on the titanium (ICDD, 089-3725). Subsequent coating processes for collagen and BMP-2 did not display additional diffraction peaks, but maintained the diffraction patterns of the HA-coated titanium. The presence of collagen was verified by infrared absorption analysis. When comparing these modifications with UC surfaces, only the CH coating displayed significantly greater peri-implant bone formation and BIC (P = .003 and P < .001, respectively). Adding BMP-2 to the implant surface did not produce any advantage compared with the CH coating.

CONCLUSIONS

In this study, the CH group displayed significantly greater new bone formation and BIC than the other groups. There was no significant difference among the other groups.

Evaluation of osseointegration of titanium alloyed implants modified by plasma polymerization

By means of plasma polymerization, positively charged, nanometre-thin coatings can be applied to implant surfaces. The aim of the present study was to quantify the adhesion of human bone cells in vitro and to evaluate the bone ongrowth in vivo, on titanium surfaces modified by plasma polymer coatings. Different implant surface configurations were examined: titanium alloy (Ti6Al4V) coated with plasma-polymerized allylamine (PPAAm) and plasma-polymerized ethylenediamine (PPEDA) versus uncoated. Shear stress on human osteoblast-like MG-63 cells was investigated in vitro using a spinning disc device. Furthermore, bone-to-implant contact (BIC) was evaluated in vivo. Custom-made conical titanium implants were inserted at the medial tibia of female Sprague-Dawley rats. After a follow-up of six weeks, the BIC was determined by means of histomorphometry. The quantification of cell adhesion showed a significantly higher shear stress for MG-63 cells on PPAAm and PPEDA compared to uncoated Ti6Al4V. Uncoated titanium alloyed implants showed the lowest BIC (40.4%). Implants with PPAAm coating revealed a clear but not significant increase of the BIC (58.5%) and implants with PPEDA a significantly increased BIC (63.7%). In conclusion, plasma polymer coatings demonstrate enhanced cell adhesion and bone ongrowth compared to uncoated titanium surfaces.

Angiopoietin-1 peptide QHREDGS promotes osteoblast differentiation, bone matrix deposition and mineralization on biomedical materials

Bone loss occurs as a consequence of a variety of diseases as well as from traumatic injuries, and often requires therapeutic intervention. Strategies for repairing and replacing damaged and/or lost bone tissue include the use of biomaterials and medical implant devices with and without osteoinductive coatings. The soluble growth factor angiopoietin-1 (Ang-1) has been found to promote cell adhesion and survival in a range of cell types including cardiac myocytes, endothelial cells and fibroblasts through an integrin-dependent mechanism. Furthermore, the short sequence QHREDGS has been identified as the integrin-binding sequence of Ang-1 and as a synthetic peptide has been found to possess similar integrin-dependent effects as Ang-1 in the aforementioned cell types. Integrins have been implicated in osteoblast differentiation and bone mineralization, processes critical to bone regeneration. By binding integrins on the osteoblast surface, QHREDGS could promote cell survival and adhesion, as well as conceivably osteoblast differentiation and bone mineralization. Here we immobilized QHREDGS onto polyacrylate (PA)-coated titanium (Ti) plates and polyethylene glycol (PEG) hydrogels. The osteoblast differentiation marker, alkaline phosphatase, peaked in activity 4-12 days earlier on the QHREDGS-immobilized PA-coated Ti plates than on the unimmobilized, DGQESHR (scrambled)- and RGDS-immobilized surfaces. Significantly more bone matrix was deposited on the QHREDGS-immobilized Ti surface than on the other surfaces as determined by atomic force microscopy. The QHREDGS-immobilized hydrogels also had a significantly higher mineral-to-matrix (M/M) ratio determined by Fourier transform infrared spectroscopy. Alizarin Red S and von Kossa staining and quantification, and environmental scanning electron microscopy showed that while both the QHREDGS- and RGDS-immobilized surfaces had extensive mineralization relative to the unimmobilized and DGQESHR-immobilized surfaces, the mineralization was more considerable on the QHREDGS-immobilized surface, both with and without the induction of osteoblast differentiation. Finally, treatment of cell monolayers with soluble QHREDGS was demonstrated to upregulate osteogenic gene expression. Taken together, these results demonstrate that the QHREDGS peptide is osteoinductive, inducing osteoblast differentiation, bone matrix deposition and mineralization.

The topical administration of bisphosphonates in implant surgery: a randomized split-mouth prospective study with a follow-up up to 5 years

OBJECTIVE

To evaluate the efficacy of the topical administration of bisphosphonates in implant therapy.

MATERIALS AND METHODS

Thirty-nine consecutive patients were selected for a split-mouth study. Inclusion criteria were: presence of a bilateral or total edentulism, ability to tolerate conventional implant procedures, older than 18 years. Ten patients were smokers. Ten patients were fully edentulous in both maxilla and mandible, 12 patients had fully edentulous maxilla or mandible, and 17 were bilaterally partially edentulous (9 in the mandible and 8 in the maxilla). A one-stage procedure was adopted in all cases. The prosthetic phase started 10 weeks after implant insertion. Each patient received implants on the control side and the test side, with insertion performed in the conventional way on the control side; on the test side, a 3% clodronate solution mixed with a surfactant (Tween-20) at a 1:3 ratio was topically administered both at the implant surface and at the implant site.

RESULTS

One hundred fifty-five implants were inserted. The test and control groups included 75 and 80 implants, respectively. The implant insertion torque was no less than 30 Ncm. A total of 7 implants failed in the control group (6 before loading and one after 12 months of loading). No failure occurred on the test side. By the 5-year follow-up, no further implant failure had been recorded. Overall, implant survival rates at 5 years for the test and control groups were, respectively, 100% and 91.3%, the difference being significant (p < .01). Mean marginal bone loss was 0.85 ± 0.71 mm in the test group and 1.12 ± 0.85 mm in the control group after 1 year of loading and stable thereafter. The difference was not significant.

CONCLUSIONS

The topical administration of bisphosphonates may positively affect implant survival in the preloading and postloading phases in partially and fully edentulous patients. However, a larger study population is needed to verify these promising clinical results.

The in vivo effect of P-15 coating on early osseointegration

The aim of this study was to evaluate mechanically and morphologically the effect of a specific peptide sequence P-15, when incorporated into implant surfaces. Three types of implants were used for the study: Group A: commercially pure titanium implant (blasted and acid etched) + electrochemical thin calcium phosphate deposition, Group B: commercially pure titanium implant (blasted and acid etched) + electrochemical thin calcium phosphate deposition + P-15 incorporation, and as control, Group C: commercially pure titanium implant (blasted and acid etched). After a topographical characterization, transcortical osteotomies were made, and all implant groups (102 implants per group) were randomly placed bilaterally in the tibiae of adult beagle dogs (n = 24). At, 1, 2, and 4 weeks post-surgery, the animals were sacrificed and the samples were retrieved for removal torque tests, for nano indentation, and for histomorphometrical analysis. The results (mean ± 95% CI) showed that Group B (34.4 ± 8.7%) presented statistically higher bone-to-implant contact than the other groups (A = 23.9 ± 7.8%; C = 21.7 ± 8.3%) at 1 week, indicating an enhanced osteogenesis due to the peptide incorporation. The results suggested that the incorporation of P-15 to implant surfaces increased its bioactivity and the effects were notable especially in the early stages of the healing process.

An artificial fusion protein between bone morphogenetic protein 2 and titanium-binding peptide is functional in vivo

The purpose of this study was to investigate osteogenesis using an artificial fusion protein (AFP) composed of modified bone morphogenetic protein 2 (BMP-2) with a titanium (Ti)-binding peptide (TBP) motif on a Ti surface in vivo. In the in vivostudy, 5-μm thick Ti was coated with electron cyclotron resonance sputtering on a porous carbon scaffold which was then dipped in one of three different mixtures of collagen gel: (1) collagen gel only, (2) collagen gel with TBP, and (3) collagen gel with the AFP between BMP-2 and the TBP motif (AFP-TBP-BMP-2). These scaffolds were then implanted into rat abdominal muscles and were studied histologically at various times and the expression of several bone-related protein messenger RNAs (mRNAs) was also analyzed. The Ti-coated scaffold of the collagen gel with AFP-TBP-BMP-2 produced cartilage in the muscle and the expression of alkaline phosphatase, bone sialoprotein, and runt-related gene 2 mRNAs was significantly increased. These results suggest that the scaffold of the collagen gel with AFP-TBP-BMP-2 accelerates osteogenesis in vivo.

Adsorption of arginine-glycine-aspartate tripeptide onto negatively charged rutile (110) mediated by cations: the effect of surface hydroxylation

Classical molecular dynamics (MD) simulations were employed to investigate the adsorption behaviors of arginine-glycine-aspartate (RGD) tripeptide onto the negatively charged hydroxylated/nonhydroxylated rutile (110) surfaces, mediated by biologically important cations (Na+ or Ca2+). The simulation results indicate that the inherent nature of the cation determines its binding strength, thereby regulating the adsorption geometry of the peptide. The sparse hydroxyl groups on the nonhydroxylated rutile diminish the probability of H-bond formation between RGD and the surface, resulting in an early desorption of the peptide even with a mediating Na+ ion. In contrast, the negatively charged aspartate (Asp) side chain is bridged to the negatively charged hydroxylated rutile by an inner-sphere Na+ ion, in coordination with the Asp-rutile hydrogen bonds at the anchoring sites. The inner- and outer-sphere Ca2+ ions are demonstrated to be capable of "trapping" RGD on both hydroxylated and nonhydroxylated rutile, in the absence of hydrogen bonds with the surface. The strongly bound inner-sphere mediating Ca2+ ion exerts a "gluing" effect on the Asp side chain, producing a tightly packed RGD-rutile complex, whereas a less localized distribution density of the outer-sphere mediating Ca2+ ion results in a higher mobility of the Asp side chain. The intramolecular interaction is suggested to facilitate the structural stability of RGD adsorbed on the negative rutile in a "horseshoe" configuration.

A novel cyclic RGD-containing peptide polymer improves serum-free adhesion of adipose tissue-derived mesenchymal stem cells to bone implant surfaces

Seeding of bone implants with mesenchymal stem cells (MSCs) may promote osseointegration and bone regeneration. However, implant material surfaces, such as titanium or bovine bone mineral, fail to support rapid and efficient attachment of MSCs, especially under serum-free conditions that may be desirable when human applications or tightly controlled experiments are envisioned. Here we demonstrate that a branched poly[Lys(Ser(i)-DL-Ala(m))] polymer functionalized with cyclic arginyl-glycyl-aspartate, when immobilized by simple adsorption to tissue culture plastic, surgical titanium alloy (Ti6Al4V), or Bio-Oss(®) bovine bone substitute, significantly accelerates serum-free adhesion and enhances seeding efficiency of human adipose tissue-derived MSCs. Moreover, when exposed to serum-containing osteogenic medium, MSCs survived and differentiated on the peptide-coated scaffolds. In summary, the presented novel polypeptide conjugate can be conveniently used for coating various surfaces, and may find applications whenever quick and efficient seeding of MSCs is required to various scaffolds in the absence of serum.

Cyclic-RGD is as effective as rhBMP-2 in anterior interbody fusion of the sheep cervical spine

STUDY DESIGN

Radiological and histological assessment of fusion status after anterior cervical discectomy and fusion (ACDF) procedure in a sheep spinal fusion model.

OBJECTIVE

To evaluate the efficacy of cyclic arginine-glycine-aspartic (cRGD) in comparison with recombinant human bone morphogenetic protein-2 (rhBMP-2) on a mineralized collagen matrix (MCM).

SUMMARY OF BACKGROUND DATA

A previous evaluation of MCM alone in comparison with autologous bone graft alone was not able to show an advantage on spinal fusion. The cRGD peptide sequence plays a major role in mediating cell adhesion. Studies have demonstrated enhances osteoblasts adhesion resulting in increased periimplant bone formation after implantcoating with cRGD. rhBMP-2 has already proven its ability to enhance spinal fusion. To date, no comparative in vivo evaluation of cRGD and rhBMP-2 in combination with a MCM for spinal fusion has been performed.

METHODS

Twenty-four sheep (N = 8/group) underwent C3-C4 fusion. Implants: group 1: titanium cage with MCM and rhBMP-2; group 2: titanium cage with MCM and cRGD; control group: titanium cage with MCM alone. After 12 weeks fusion sites were evaluated by computed tomography to assess fusion status, bone mineral density as well as bony callus volume. Furthermore, histomorphological and histomorphometrical analysis of the fusion sites were performed.

RESULTS

In comparison with the control group, cRGD, and rhBMP-2 groups showed a higher fusion rate in radiographical findings and a higher degree of interbody fusion in histomorphometrical analysis (P < 0.05). There was no significant difference in radiographical and histological parameters between the rhBMP-2 and the cRGD group. Although rhBMP-2 demonstrated ectopic prevertebral bone formations, this effect was less prominent in the cRGD group.

CONCLUSION

In this animal model the combination of cRGD and a mineralized collagen matrix showed superior fusion results in comparison with the mineralized collagen alone. Further, cRGD was comparably effective to rhBMP-2 in promoting interbody fusion by demonstrating less ectopic bone formations.

Covalent attachment of P15 peptide to titanium surfaces enhances cell attachment, spreading, and osteogenic gene expression

P15, a synthetic 15 amino acid peptide, mimics the cell-binding domain within the alpha-1 chain of human collagen is being tested in clinical trials to determine if it enhances bone formation in spinal fusions. We hypothesize that covalent attachment of P15 to titanium implants may also serve to promote osseointegration. To test this hypothesis, we measured osteoblast and mesenchymal cell adhesion, proliferation, and maturation on P15 tethered to a titanium (Ti-P15) surface. P15 peptide was covalently bonded to titanium alloy surfaces and incubated with osteoblast like cells. Cell toxicity, adhesion, spreading, and differentiation was then evaluated. Real-time quantitative PCR, Western blot analysis, and fluorescent immunohistochemistry was performed to measure osteoblast gene expression and differentiation. There was no evidence of toxicity. Significant increases in early cell attachment, spreading, and proliferation were observed on the Ti-P15 surface. Increased filapodial attachments, α(2) integrin expression, and phosphorylated focal adhesion kinase immunostaining indicated activation of integrin signaling pathways. qRT-PCR analysis indicated there was significant increase in osteogenic differentiation markers in cells grown on Ti-P15 compared to control-Ti. Western blotting confirmed these findings. Surface modification of titanium with P15 significantly increased cell attachment, spreading, osteogenic gene expression, and differentiation. Results of this study suggest that Ti-P15 has the potential to safely enhance bone formation and promote osseointegration of titanium implants.

Surface modification and drug delivery for biointegration

Biointegration refers to the interconnection between a biomedical device and the recipient tissue. In many implant devices, the lack of proper biointegration can cause device failure and potentially serious medical problems. This review summarizes the recent progress in surface chemistry, drug delivery and antifouling methods to improve the biointegration of implants. Much progress has been made as our understanding of biological systems and material properties expands and as new technologies become available. This article addresses methods of enhancing biointegration by means of modifying implant surface chemistry and by drug-delivery approaches.

Fabrication and in vitro evaluation of the collagen/hyaluronic acid PEM coating crosslinked with functionalized RGD peptide on titanium

Surface modification of titanium (Ti) using biomolecules has attracted much attention recently. In this study, a new strategy has been employed to construct a stable and bioactive coating on Ti. To this end, a derivative of hyaluronic acid (HA), i.e. HA-GRGDSPC-(SH), was synthesized. The disulfide-crosslinked Arg-Gly-Asp (RGD)-containing collagen/hyaluronic acid polyelectrolyte membrane (PEM) coating was then fabricated on Ti through the alternate deposition of collagen and HA-GRGDSPC-(SH) with five assembly cycles and subsequent crosslinking via converting free sulphydryl groups into disulfide linkages (RGD-CHC-Ti group). The assembly processes for PEM coating and the physicochemical properties of the coating were carefully characterized. The stability of PEM coating in phosphate-buffered saline solution could be adjusted by the crosslinking degree, while its degradation behaviors in the presence of glutathione were glutathione concentration dependent. The adhesion and proliferation of MC3T3-E1 cells were significantly enhanced in the RGD-CHC-Ti group. Up-regulated bone specific genes, enhanced alkaline phosphatase activity and osteocalcin production, the increased areas of mineralization were also observed in the RGD-CHC-Ti group. These results indicate that the strategy employed herein may function as an effective way to construct stable, RGD-containing bioactive coatings on Ti.

RGD peptide immobilized on TiO2 nanotubes for increased bone marrow stromal cells adhesion and osteogenic gene expression

Recently, TiO(2) nanotube layers are widely used in orthopedics and dental applications because of their good promotion effect on bone cells. Furthermore, peptide sequences such as arginine-glycine-aspartic acid are used to modify Ti implant for binding to cell surface integrins through motif. In this study, a cellular adhesive peptide of arginine-glycine-aspartic acid-cysteine (RGDC) was immobilized onto anodized TiO(2) nanotubes on Ti to examine its in vitro responses on rat bone marrow stromal cells (BMSCs). Materials were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy techniques. High-resolution C1s scans suggested the presence of RGDC on the surface and SEM images confirmed the nanotubes were not destroyed after modification. BMSCs adhesion and osteogenic gene expression were detected in TiO(2) nanotube layers with and without RGDC modification by fluorescence microscopy, confocal laser scanning microscopy, SEM, and realtime polymerase chain reaction (Real-time PCR). Results showed that the TiO(2) nanotube layers immobilized with RGDC increased BMSCs adhesion compared to nonfunctionalized nanotubes after 4 h of cultivation. Furthermore, the osteogenic gene expression of BMSCs was dramatically enhanced on the TiO(2) nanotube layers immobilized with RGDC (10 mM) compared to the TiO(2) nanotube layers immobilized with RGDC (1 mM) and non-functionalized anodized Ti. Our results from in vitro study provided evidence that Ti anodized to possess nanotubes and then further functionalized with RGDC should be further studied for the design of better biomedical implant surfaces.

Effect of oligonucleotide mediated immobilization of bone morphogenic proteins on titanium surfaces

The aim of the present study was to test the hypothesis that oligonucleotides can be used for anchorage and slow release of osteogenic growth factors such as BMP to enhance the osteogenic activity of a titanium implant surface. Strands of 60-mer non-coding DNA oligonucleotides (ODN) were bound to an acid-etched sandblasted cp Ti-surface by nanomechanical fixation using anodic polarization. RhBMP2 that had been conjugated to complementary strands of DNA oligonucleotides was then bound to the anchored ODN strands by hybridization. Binding studies showed a higher binding capacity compared to non-conjugated BMP2. Long term release experiments demonstrated a continuous release from all surfaces that was lowest for the conjugated BMP2 bound to the ODN anchor strands. Proliferation of human bone marrow stroma cells (hBMSC) was significantly increased on these surfaces. Immunofluorescence showed that hBMSC grown on surfaces coated with specifically bound conjugated BMP2 developed significantly higher numbers of focal adhesion points and exhibited significantly higher levels of transcription of osteogenic markers alkaline phosphatase and osteopontin at early intervals. Biological activity (induction of alkaline phosphatase) of conjugated BMP2 released from the surface was comparable to released non-conjugated BMP2, indicating that conjugation did not negatively affect the activity of the released molecules. In conclusion the present study has shown that BMP2 conjugated to ODN strands and hybridized to complementary ODN strands anchored to a titanium surface has led to slow growth factor release and can enhance the osteogenic activity of the titanium surface.

Bone Regeneration around Dental Implants as a Treatment for Peri-Implantitis: A Review of the Literature

This manuscript discusses peri-implantitis around dental implants and the current methodologies of surgical and non-surgical approaches towards treating peri-implantitis. Mechanical, chemical cleansing and reactivation of infected implant surface along with recent advances like the use of Laser and Photodynamic therapy (PDT) have also been reviewed in this literature. Bone regenerative treatment methods for the treatment of peri-implantitis using non-resorbable membranes (Guided Bone Regeneration), autogenous bone grafts and bone substitute materials with recombinant human bone morphogenetic protein-2 (rhBMP-2) and other growth factors have also been reviewed in this manuscript.

Advantages of RGD peptides for directing cell association with biomaterials

Despite many years of in vitro research confirming the effectiveness of RGD in promoting cell attachment to a wide variety of biomaterials, animal studies evaluating tissue responses to implanted RGD-functionalized substrates have yielded more variable results. The goals of this report are to present some of the reasons why cell culture studies may not always reliably predict in vivo responses, and more importantly, to highlight potential applications that may benefit from the use of RGD peptides.

Bone healing of commercial oral implants with RGD immobilization through electrodeposited poly(ethylene glycol) in rabbit cancellous bone

Immobilization of RGD peptides on titanium (Ti) surfaces enhances implant bone healing by promoting early osteoblastic cell attachment and subsequent differentiation by facilitating integrin binding. Our previous studies have demonstrated the efficacy of RGD peptide immobilization on Ti surfaces through the electrodeposition of poly(ethylene glycol) (PEG) (RGD/PEG/Ti), which exhibited good chemical stability and bonding. The RGD/PEG/Ti surface promoted differentiation and mineralization of pre-osteoblasts. This study investigated the in vivo bone healing capacity of the RGD/PEG/Ti surface for biomedical application as a more osteoconductive implant surface in dentistry. The RGD/PEG/Ti surface was produced on an osteoconductive implant surface, i.e. the grit blasted micro-rough surface of a commercial oral implant. The osteoconductivity of the RGD/PEG/Ti surface was compared by histomorphometric evaluation with an RGD peptide-coated surface obtained by simple adsorption in rabbit cancellous bone after 2 and 4 weeks healing. The RGD/PEG/Ti implants displayed a high degree of direct bone apposition in cancellous bone and achieved greater active bone apposition, even in areas of poor surrounding bone. Significant increases in the bone to implant contact percentage were observed for RGD/PEG/Ti implants compared with RGD-coated Ti implants obtained by simple adsorption both after 2 and 4 weeks healing (P<0.05). These results demonstrate that RGD peptide immobilization on a Ti surface through electrodeposited PEG may be an effective method for enhancing bone healing with commercial micro-rough surface oral implants in cancellous bone by achieving rapid bone apposition on the implant surface.