The solvation of electrons by an atmospheric-pressure plasma

Mimicking lightning-induced electrochemistry on the early Earth

To test the hypothesis that an abiotic Earth and its inert atmosphere could form chemically reactive carbon- and nitrogen-containing compounds, we designed a plasma electrochemical setup to mimic lightning-induced electrochemistry under steady-state conditions of the early Earth. Air-gap electrochemical reactions at air-water-ground interfaces lead to remarkable yields, with up to 40 moles of carbon dioxide being reduced into carbon monoxide and formic acid, and 3 moles of gaseous nitrogen being fixed into nitrate, nitrite, and ammonium ions, per mole of transmitted electrons. Interfaces enable reactants (e.g., minerals) that may have been on land, in lakes, and in oceans to participate in radical and redox reactions, leading to higher yields compared to gas-phase-only reactions. Cloud-to-ground lightning strikes could have generated high concentrations of reactive molecules locally, establishing diverse feedstocks for early life to emerge and survive globally.

Optical and Chemical Measurements of Solvated Electrons Produced in Plasma Electrolysis with a Water Cathode

It is known that glow discharges with a water anode inject and form solvated electrons at the plasma-liquid interface, driving a wide variety of reduction reactions. However, in systems with a water cathode, the production and role of solvated electrons are less clear. Here, we present evidence for the direct detection of solvated electrons produced at the interface of an argon plasma and a water cathode via absorption spectroscopy. We further quantify their yield using the dissociative electron attachment of chloroacetate, measuring a yield of 1.04 ± 0.59 electrons per incident ion, corresponding to approximately 100% faradaic efficiency. Additionally, we estimate a yield of 2.09 ± 0.93 hydroxyl radicals per incident ion. Comparison of this yield with other findings in the literature supports that these hydroxyl radicals are likely formed directly in the liquid phase rather than by diffusion from the vapor phase.

Evidence for Superoxide-Initiated Oxidation of Aniline in Water by Pulsed, Atmospheric Pressure Plasma

Plasma-driven solution electrochemistry (PDSE) uses plasma-generated reactive species to drive redox reactions in solution. Nonthermal, atmospheric pressure plasmas, when irradiating water, produce many redox species. While PDSE is a promising chemical tool, there is limited insight into the mechanisms of the reactions due to the variety of short-lived reagents produced. In this study, we use aniline as a model system for studying redox mechanisms of PDSE. We show that the plasma irradiation of aqueous aniline solutions drives the formation of polyaniline oligomer, which is suppressed under acidic starting conditions. The addition of (2,2,6,6-Tetramethylpiperidin-1-yl)oxyl (TEMPO), a radical scavenger, decreases the formation of oligomer by 80%, and the addition of superoxide dismutase fully hinders oligomerization. These results lead us to conclude that the oligomerization of aniline by plasma irradiation is initiated by superoxide. This discovery provides novel insights into PDSE mechanisms and illustrates a potential method of harnessing superoxide for chemical reactions.

Harnessing plasma-generated reactive species for the synthesis of different phases of molybdenum oxide to study adsorption and photocatalytic activity

This study employs plasma-liquid interaction technique to synthesize different phases of molybdenum oxide using air and argon as plasma-forming gases. In situ plasma-generated nitrogen species primarily NO3-/NO2- and hydrogen species (H+) facilitate the reduction of the molybdenum precursor anion (Mo7O24-). The reduced Mo species subsequently reacts with reactive oxygen species, forming MoO6 octahedra, which is the building block of a molybdenum oxide crystal. Varied concentrations of NO3-/NO2- and H+ species in air and argon plasma treatment significantly influence the growth process. Air plasma synthesis yields hexagonal molybdenum oxide microrods, which upon calcination changes its phase to orthorhombic 2D layered structure. Moreover, the argon plasma synthesized sample exhibits a mixed phase of hexagonal and orthorhombic molybdenum oxide due to the heavy argon ion bombardment, inducing material porosity and surface oxygen vacancies. The mixed-phase material exhibits superior adsorption and photo-degradation towards cationic dye compared to the other two phases. The higher photocatalytic performance may be responsible for the extended lifetime of the photo-generated charge carriers possessed by the mixed-phase material. Radical scavenging tests have identified holes and hydroxyl radicals as the key reactive species that take part in the photo-degradation process.

Electric Field Effect of the Plasma-Initiated Polymerization of Methyl Methacrylate: A Negatively Charged Long-Lived Radical

Plasma-initiated polymerization (PIP) is generally attributed to a radical process due to its inhibiting property. However, its unique polymerization behaviors like long-lived radical and solvent effect do not comply well with the traditional radical mechanism. Herein, the PIP of methyl methacrylate (MMA) was conducted in a high-voltage DC electric field to investigate the charged nature of its radicals. Consequently, the polymerization presented a preferential distribution of polymers at the anode but not the cathode, revealing the negatively charged nature of the growing radicals. An acceleration phenomenon, accompanied by the growth in molecular weights and the reduction in molecular weight distributions (Ð), was observed at the voltages above 16 kV, suggesting the dissociation of ion pairs of growing radicals. The PIP yielded PMMA with analogous chemical and steric structures to those of PMMA from traditional radical initiation, whether in the presence or absence of the external electric field. This work offers new insights into the PIP of vinyl monomers, wherein a one-electron transfer reaction is inferred to be involved in the monomer activation.

Plasma-liquid interactions in the presence of organic matter-A perspective

As investigations in the biomedical applications of plasma advance, a demand for describing safe and efficacious delivery of plasma is emerging. It is quite clear that not all plasmas are "equal" for all applications. This Perspective discusses limitations of the existing parameters used to define plasma in context of the need for the "right plasma" at the "right dose" for each "disease system." The validity of results extrapolated from in vitro studies to preclinical and clinical applications is discussed. We make a case for studying the whole system as a single unit, in situ. Furthermore, we argue that while plasma-generated chemical species are the proposed key effectors in biological systems, the contribution of physical effectors (electric fields, surface charging, dielectric properties of target, changes in gap electric fields, etc.) must not be ignored.

Effects of Halides on Organic Compound Degradation during Plasma Treatment of Brines

Plasma has been proposed as an alternative strategy to treat organic contaminants in brines. Chemical degradation in these systems is expected to be partially driven by halogen oxidants, which have been detected in halide-containing solutions exposed to plasma. In this study, we characterized specific mechanisms involving the formation and reactions of halogen oxidants during plasma treatment. We first demonstrated that addition of halides accelerated the degradation of a probe compound known to react quickly with halogen oxidants (i.e., para-hydroxybenzoate) but did not affect the degradation of a less reactive probe compound (i.e., benzoate). This effect was attributed to the degradation of para-hydroxybenzoate by hypohalous acids, which were produced via a mechanism involving halogen radicals as intermediates. We applied this mechanistic insight to investigate the impact of constituents in brines on reactions driven by halogen oxidants during plasma treatment. Bromide, which is expected to occur alongside chloride in brines, was required to enable halogen oxidant formation, consistent with the generation of halogen radicals from the oxidation of halides by hydroxyl radical. Other constituents typically present in brines (i.e., carbonates, organic matter) slowed the degradation of organic compounds, consistent with their ability to scavenge species involved during plasma treatment.

Two-photon Absorption and Photoionization of a Bacterial Phytochrome

Phytochromes constitute a family of photosensory proteins that are utilized by various organisms to regulate several physiological processes. Phytochromes bind a bilin pigment that switches its isomeric state upon absorption of red or far-red photons, resulting in protein conformational changes that are sensed by the organism. Previously, the ultrafast dynamics in bacterial phytochrome was resolved to atomic resolution by time-resolved serial femtosecond X-ray diffraction (TR-SFX), showing extensive changes in its molecular conformation at 1 picosecond delay time. However, the large excitation fluence of mJ/mm2 used in TR-SFX questions the validity of the observed dynamics. In this work, we present an excitation-dependent ultrafast transient absorption study to test the response of a related bacterial phytochrome to excitation fluence. We observe excitation power-dependent sub-picosecond dynamics, assigned to the population of high-lying excited state Sn through resonantly enhanced two-photon absorption, followed by rapid internal conversion to the low-lying S1 state. Inspection of the long-lived spectrum under high fluence shows that in addition to the primary intermediate Lumi-R, spectroscopic signatures of solvated electrons and ionized chromophore radicals are observed. Supported by numerical modelling, we propose that under excitation fluences of tens of μJ/mm2 and higher, bacterial phytochrome partly undergoes photoionization from the Sn state in competition with internal conversion to the S1 state in 300 fs. We suggest that the extensive structural changes of related, shorter bacterial phytochrome, lacking the PHY domain, resolved from TR-SFX may have been affected by the ionized species. We propose approaches to minimize the two-photon absorption process by tuning the excitation spectrum away from the S1 absorption or using phytochromes exhibiting minimized or shifted S1 absorption.

Spectroscopy and dynamics of the hydrated electron at the water/air interface

The hydrated electron, e-(aq), has attracted much attention as a central species in radiation chemistry. However, much less is known about e-(aq) at the water/air surface, despite its fundamental role in electron transfer processes at interfaces. Using time-resolved electronic sum-frequency generation spectroscopy, the electronic spectrum of e-(aq) at the water/air interface and its dynamics are measured here, following photo-oxidation of the phenoxide anion. The spectral maximum agrees with that for bulk e-(aq) and shows that the orbital density resides predominantly within the aqueous phase, in agreement with supporting calculations. In contrast, the chemistry of the interfacial hydrated electron differs from that in bulk water, with e-(aq) diffusing into the bulk and leaving the phenoxyl radical at the surface. Our work resolves long-standing questions about e-(aq) at the water/air interface and highlights its potential role in chemistry at the ubiquitous aqueous interface.

A review of innovative approaches for onsite management of PFAS-impacted investigation derived waste

The historic use of aqueous film-forming foam (AFFF) has led to widespread detection of per- and polyfluoroalkyl substance (PFAS) in groundwater, soils, sediments, drinking water, wastewater, and receiving aquatic systems throughout the United States (U.S.). Prior to any remediation activities, in order to identify the PFAS-impacted source zones and select the optimum management approach, extensive site investigations need to be conducted. These site investigations have resulted in the generation of considerable amount of investigation-derived waste (IDW) which predominantly consists of well purging water and drill fluid, equipment washing residue, soil, drill cuttings, and residues from the destruction of asphalt and concrete surfaces. IDW is often impacted by varying levels of PFAS which poses a substantial challenge concerning disposal to prevent potential mobilization of PFAS, logistical complexities, and increasing requirement for storage as a result of accumulation of the associated wastes. The distinct features of IDW involve the intermittent generation of waste, substantial volume of waste produced, and the critical demand for onsite management. This article critically focuses on innovative technologies and approaches employed for onsite treatment and management of PFAS-impacted IDW. The overall objective of this study centers on developing and deploying end-of-life treatment technology systems capable of facilitating unrestricted disposal, discharge, and/or IDW reuse on-site, thereby reducing spatial footprints and mobilization time.

Silver Nanoparticle Synthesis in Glycerol by Low-Pressure Plasma-Driven Electrolysis: The Roles of Free Electrons and Photons

Low-temperature plasmas in and in contact with liquids have emerged as a catalyst-free approach for the selective, electrode-free, and green synthesis of novel materials. For the synthesis of nanomaterials, short-lived solvated electrons have been proposed to be the critical reducing species, while the role of ultraviolet (UV) photons from plasma is less explored. Here, we demonstrate that UV radiation contributes ∼70% of the integral plasma effect in synthesizing silver (Ag) nanoparticles within a glycerol solution. We suggest that the UV radiation causes C-H bond cleavage of the glycerol molecules, with an experimentally and theoretically determined threshold photon energy of only 5 eV. The photon-induced dissociation leads to the formation of glycerol fragmentation radicals, causing the reduction of Ag+ ions to Ag neutrals, enabling nanoparticle formation in the liquid phase.

Controlled Radical Polymerization Initiated by Solvated Electrons

Solvated electron (esol - ) is highly reducing species and apt to initiate monomers via one-electron transfer reaction. Herein, utilizing the esol - solution of Na/hexamethylphosphoramide, radical and anionic initiations are observed respectively, which heavily depend on Na concentrations. Interestingly, this initiation system, in states of lower Na concentrations, higher molar conductivities and less paired esol - , give rise to a controlled radical polymerization (CRP) to yield polymers with predictable molecular weights and narrow molecular weight distributions (the lowest Ð = 1.25). This CRP presents unique behaviors, like solvent effect, electric field effect, and unusual copolymerization phenomenon. A semi-conjugated radical carrying a negative charge is proposed to be responsible for the CRP. This system gives a distinct way to regulate CRP from current CRPs, and offers new insights into the monomer initiation by esol - .

Experimental investigation of expansive bending pipe flow separation control using a surface dielectric barrier discharge plasma actuator

Adverse pressure gradients can cause severe flow separation within typical S-shaped inlets. This results in a total pressure distortion at the aerodynamic interface plane (AIP). The expansive bending pipe, where flow separation also occurs due to the adverse pressure gradient, is the basis for investigations into S-shaped inlets. In this study, surface dielectric barrier discharge (SDBD) plasma actuators are used to moderate the total pressure distortion in the AIP of an expansive bending pipe under a 10 m/s incoming flow. Also, the influences of actuation voltage amplitude and pulsed frequency on the total pressure distortion of the AIP are investigated under two plasma actuation modes, nanosecond pulsed SDBD and alternating current (AC) SDBD. Under optimal actuation parameters, the nanosecond pulsed SDBD and the AC-SDBD can reduce the distortion index by 14.93% and 32.22%, respectively. The results demonstrate the effectiveness of SDBD plasma actuators in suppressing flow separation within expansive bending pipes.

Plasma-assisted degradation of a short-chain perfluoroalkyl substance (PFAS): Perfluorobutane sulfonate (PFBS)

This study investigates the degradation of perfluorobutane sulfonate (PFBS), a chemical compound belonging to a group of per- and polyfluoroalkyl substances (PFAS), by gas-phase electrical discharge plasma. Plasma alone was ineffective in degrading PFBS due to its poor hydrophobicity, which inhibited the compound from accumulating at the plasma-liquid interface, the region of chemical reactivity. To overcome bulk liquid mass transport limitations, a surfactant, hexadecyltrimethylammonium bromide (CTAB), was introduced to interact with and transport PFBS to the plasma-liquid interface. In the presence of CTAB, ∼99% of PFBS was removed from the bulk liquid and concentrated at the interface, where 67% of the concentrate was degraded and 43% of that amount was defluorinated within one hour. PFBS degradation was further improved by optimizing the surfactant concentration and dosage. Experiments with a range of cationic, non-ionic, and anionic surfactants revealed that the PFAS-CTAB binding mechanism is predominantly electrostatic. A mechanistic understanding of the PFAS-CTAB complex formation, its transport to and destruction at the interface is proposed, alongside the chemical degradation scheme, which includes the identified degradation byproducts. This study shows that surfactant-assisted plasma treatment is one of the most promising techniques for destroying short-chain PFAS in contaminated water.

Creation and Reaction of Solvated Electrons at and near the Surface of Water

Solvated electrons (e_s^-) are among nature's most powerful reactants, with over 2600 reactions investigated in bulk water. These electrons can also be created at and near the surface of water by exposing an aqueous microjet in vacuum to gas-phase sodium atoms, which ionize into e_s^- and Na⁺ within the top few layers. When a reactive surfactant is added to the jet, the surfactant and e_s^- become coreactants localized in the interfacial region. We report the reaction of e_s^- with the surfactant benzyltrimethylammonium in a 6.7 M LiBr/water microjet at 235 K and pH = 2. The reaction intermediates trimethylamine (TMA) and benzyl radical are identified by mass spectrometry after they evaporate from solution into the gas phase. Their detection demonstrates that TMA can escape before it is protonated and benzyl before it combines with itself or a H atom. Diffusion-reaction calculations indicate that e_s^- reacts on average within 20 Å of the surface and perhaps within the surfactant monolayer itself, while unprotonated TMA evaporates from the top 40 Å. The escape depth exceeds 1300 Å for the more slowly reacting benzyl radical. These proof-of-principle experiments establish an approach for exploring the near-interfacial analogues of aqueous bulk-phase radical chemistry through the evaporation of reaction intermediates into the gas phase.

Plasma Electrochemistry for Carbon-Carbon Bond Formation via Pinacol Coupling

The formation of carbon-carbon bonds by pinacol coupling of aldehydes and ketones requires a large negative reduction potential, often realized with a stoichiometric reducing reagent. Here, we use solvated electrons generated via a plasma-liquid process. Parametric studies with methyl-4-formylbenzoate reveal that selectivity over the competing reduction to the alcohol requires careful control over mass transport. The generality is demonstrated with benzaldehydes, benzyl ketones, and furfural. A reaction-diffusion model explains the observed kinetics, and ab initio calculations provide insight into the mechanism. This study opens the possibility of a metal-free, electrically-powered, sustainable method for reductive organic reactions.

Synthesis of antibacterial hydroxypropyl methylcellulose and silver nanoparticle biocomposites via solution plasma using silver electrodes

The biocomposites of hydroxypropyl methylcellulose (HPMC)/silver nanoparticles (AgNPs) were synthesized using the solution plasma process (SPP). HPMC/AgNPs were synthesized in 1-5 % HPMC solutions using silver electrodes. UV-Vis spectroscopy showed a peak near 400 nm and the peak increased as the concentration of HPMC and discharge time increased. FTIR analysis indicated no change in the chemical structure of the HPMC based biocomposites. Spherical shaped AgNPs with size ranges about 2-18 nm and well dispersed in the porous HPMC matrices with fringed edges were observed by TEM and SEM/EDS analyses. The synthesized biocomposites were found to be thermo-stable by TGA analysis. The inhibition zones of bacterial growth formed by the HPMC/AgNPs biocomposites were in the range of 8-14.3 mm; minimal inhibition concentrations, in the range of 10-15 μg·mL^-1 for Gram-negative bacteria; 25-30 μg·mL^-1 for Gram-positive bacteria. The biocomposites were non-toxic to the HEK293 cells up to 125 μg·mL^-1. The results indicated that the synthesis of antibacterial agents in the HPMC matrix using silver electrodes via SPP would be an efficient and safe way for the development of biopolymer based antimicrobials and wound healing biomaterials.

Influence of a transient spark plasma discharge on producing high molecular masses of chemical products from L-cysteine

Cold atmospheric pressure plasmas are considered a forthcoming method in many research areas. Plasma modification of biomolecules has received much attention in addition to plasma-treated biomaterials. Hence, in this work, we operated a transient spark plasma (TSP) discharge to study its effect on the L-cysteine chemical structure. the TSP was configured in a pin-to-ring electrode arrangement and flowed by Ar gas. We also investigated the effect of two chemicals; dimethyl sulfoxide (DMSO) and hydrogen peroxide (H₂O₂) by the bubbling method to show how they can change the creation of new chemical bioproducts. Ultraviolet-Visible absorption spectroscopy, Fourier transform infrared spectroscopy and Liquid chromatography-mass spectroscopy were used to investigate any changes in chemical bonds of cysteine structure and to depict the generation of new biomolecules. Based on the displayed results plasma-generated reactive species had a great role in the chemical structure of the cysteine. Entering DMSO and H₂O₂ into the plasma caused the creation of new products and the heaviest biomolecule was produced by the simultaneous addition of DMSO and H₂O₂. The results also predicted that some chemical products and amino acids with a higher value molecular masse produced from the polymerization process of cysteine solution. The strong oxidation process is responsible for the heavy chemical compounds.

Microsolvation of electrons by a handful of ammonia molecules

Microsolvation of electrons in ammonia is studied here via anionic NH_{3 n} ^- clusters with n = 2-6. Intensive samplings of the corresponding configurational spaces using second-order perturbation theory with extended basis sets uncover rich and complex energy landscapes, heavily populated by many local minima in tight energy windows as calculated from highly correlated coupled cluster methods. There is a marked energetical preference for structures that place the excess electron external to the molecular frame, effectively coordinating it with the three protons from a single ammonia molecule. Overall, as the clusters grow in size, the lowest energy dimer serves as the basic motif over which additional ammonia molecules are attached via unusually strong charge-assisted hydrogen bonds. This is a priori quite unexpected because, on electrostatic grounds, the excess electron would be expected to be in contact with as many protons as possible. Accordingly, a full quantum mechanical treatment of the bonding interactions under the tools provided by the quantum theory of atoms in molecules is carried out in order to dissect and understand the nature of intermolecular contacts. Vertical detachment energies reveal bound electrons even for n = 2.

Estimation of in vivo toxicity of MgO/ZnO core/shell nanoparticles synthesized by eco-friendly non-thermal plasma technology

MgO/ZnO core/shell nanoparticles were synthesized using the atmosphere plasma jets technique. The physical properties of the synthesized nanoparticles were investigated by a series of techniques, including X-ray diffraction (XRD), X-ray dispersive spectroscopy (EDS), and transmission electron microscopy (TEM). XRD and EDS analyses confirmed the purity of the nanoparticles synthesized with an average nanoparticle crystallite size of 36 nm. TEM confirmed the successful synthesis of spindle-shaped MgO/ZnO core/shell nanoparticles with an average size of 70 nm. To evaluate their toxicity, the MgO/ZnO core/shell nanoparticles were tested in vivo. Twenty-five albino female rats were randomly divided into five groups (five rats in each group); one was used as the control group and the other four as the experimental groups. Doses of the MgO/ZnO core/shell nanoparticles solution were orally administered to the test groups to examine the toxicity. For 30 consecutive days, each rat in test groups 2–5 received 1 mL of the MgO/ZnO core/shell nanoparticles solution at the respective doses of 1.25, 2.5, 5, and 10 mg L⁻¹. The rats’ growth, hematology, thyroid gland function, and histopathology were examined after 30 days. Findings indicate that the growth retardation in the rats treated with MgO/ZnO core/shell nanoparticles may be due to their infection by Hyperthyroidism. The hematology results show the nonsignificant effect of MgO/ZnO core/shell nanoparticles on white blood cells, implying that these nanoparticles have no harmful impact on the immune system. Moreover, the levels of the thyroxine and thyroid‐stimulating hormones increased, and that of the triiodothyronine hormone decreased. The histological analysis results show that low concentrations of MgO/ZnO core/shell nanoparticles are safe for desired biomedical applications.

Rate, Efficiency, and Mechanisms of Electrochemical Perfluorooctanoic Acid Degradation with Boron-Doped Diamond and Plasma Electrodes

The removal of per- or polyfluorinated alkyl substances (PFAS) has received increasing attention because of their extreme stability, our increasing awareness of their toxicity at even low levels, and scientific challenges for traditional treatment methods such as separation by activated carbon or destruction by advanced oxidation processes. Here, we performed a direct and systematic comparison of two electrified approaches that have recently shown promise for effective degradation of PFAS: plasma and conventional electrochemical degradation. We tailored a reactor configuration where one of the electrodes could be a plasma or a boron-doped diamond (BDD) electrode and operated both electrodes galvanostatically by continuous direct current. We show that while both methods achieved near-complete degradation of PFAS, the plasma was only effective as the cathode, whereas the BDD was only effective as the anode. Compared to the BDD, plasma required more than an order of magnitude higher voltage but lower current to achieve similar degradation efficiency with more rapid degradation kinetics. All these factors considered, it was noted that plasma or BDD degradation resulted in similar energy efficiencies. The BDD electrode exhibited zero-order kinetics, and thus, PFAS degradation using the conventional electrochemical method was kinetically controlled. On the contrary, analysis using a film model indicated that the plasma degradation kinetics of PFAS using plasma were mass-transfer-controlled because of the fast reaction kinetics. With the help of a simple quantitative model that incorporates mass transport, interfacial reaction, and surface accumulation, we propose that the degradation reaction kinetically follows an Eley-Rideal-type mechanism for the plasma electrode, and an intrinsic rate constant of 2.89 × 10⁸ m⁴ mol^-1 s^-1 was obtained accordingly. The investigation shows that to realize the true kinetic potential of plasma degradation for water treatment, mass transfer to the interface must be enhanced.

Influences of Plasma Plume Length on Structural, Optical and Dye Degradation Properties of Citrate-Stabilized Silver Nanoparticles Synthesized by Plasma-Assisted Reduction

Citrate-capped silver nanoparticles (Ag@Cit NPs) were synthesized by a simple plasma-assisted reduction method. Homogenous colloidal Ag@Cit NPs solutions were produced by treating a AgNO3-trisodium citrate-deionized water with an atmospheric-pressure argon plasma jet. The plasma-synthesized Ag@Cit NPs exhibited quasi-spherical shape with an average particle diameter of about 5.9−7.5 nm, and their absorption spectra showed surface plasmon resonance peaks at approximately 406 nm. The amount of Ag@Cit NPs increased in a plasma exposure duration-dependent manner. Plasma synthesis of Ag@Cit NPs was more effective in the 8.5 cm plume jet than in the shorter and longer plume jets. A larger amount of Ag@Cit NPs were produced from the 8.5 cm plume jet with a higher pH and a larger number of aqua electrons, indicating that the synergetic effect between plasma electrons and citrate plays an important role in the plasma synthesis of Ag@Cit NPs. Plasma-assisted citrate reduction facilitates the synthesis of Ag@Cit NPs, and citrate-capped nanoparticles are stabilized in an aqueous solution due to their repulsive force. Next, we demonstrated that plasma-synthesized Ag@Cit NPs exhibited a significant degradation of methylene blue dye.

Intensified inactivation of model and environmental bacteria by an atmospheric-pressure air-liquid discharge plasma compared with chlorination

Water-borne pathogenic bacteria are always the top priority to be removed through disinfection process in water treatment due to their threat to human health. It was necessary to develop novel disinfection methods since the conventional chlorine disinfection was inefficient in inactivating chlorine-resistant bacteria, inducing the viable but non-culturable (VBNC) bacteria and forming disinfection by-products (DBPs). In this study, the inactivation of four model strains including Gram-negative (G^-), Gram-positive (G⁺) and environmental samples by atmospheric-pressure air-liquid discharge plasma (ALDP) was assessed systematically. The results showed that ALDP was superior in inactivating all of the samples compared with chlorination. During 10 min ALDP treatment, the G^- bacteria were completely inactivated, and the G⁺ one was inactivated by more than 4.61 logs. The inactivation of bacteria from a campus lake and a wastewater treatment plant effluent exceeded 99.82% and 97.78%, respectively. For G^- bacteria, ALDP resulted in a much lower (10²∼10³ times) levels of VBNC cells than chlorination. ALDP could effectively remove the chlorine-resistant bacteria. More than 96.41% of the intracellular DNA and 99.99% of the extracellular DNA were removed, whereas it was only 56.35% and 12.82% for chlorination. ALDP had a stronger ability to destroy cell structure than chlorination, presumably due to the existence of ROS (·OH, ¹O₂ and O₂^-). GC-MS analysis showed that ALDP produced less DBPs than chlorination. These findings provided new insights for the application of discharge plasma in water disinfection, which could be complemental or alternative to the conventional disinfection methods.

Plasma parameters and the reduction potential at a plasma-liquid interface

Nonthermal plasmas in contact with liquids have been shown to generate a variety of reactive species capable of initiating reduction-oxidation (redox) reactions at the electrochemically active plasma-liquid interface. In conventional electrochemical cells, selective redox chemistry is achieved by controlling the reduction potential at the solid electrode-electrolyte interface by applying a bias via an external circuit. In the case of plasma-liquid systems, an analogous means of tuning the reduction potential near the interface has not clearly been identified. When treated as a floating surface, the liquid is expected to adopt a net negative charge to balance the flux of hot electrons and relatively cold positive ions. The reduction potential near the plasma-liquid interface is hypothesized to be proportional to the floating potential, which can be approximated using an analytical model provided the plasma parameters are known. Herein, we present a framework for correlating the electron density and electron temperature of a noble gas plasma jet to the reduction potential near the plasma-liquid interface. The plasma parameters were acquired for an argon atmospheric plasma jet in contact with an aqueous solution by means of laser Thomson scattering. The reduction potential was determined using identical reference electrodes to measure the potential difference between the plasma-liquid interface and bulk solution. Interestingly, the measured reduction potentials near the plasma-liquid interface were found to be in good agreement with the model-predicted values determined using the plasma parameters obtained from the Thomson scattering experiments.

Plasma induced efficient removal of antibiotic-resistant Escherichia coli and antibiotic resistance genes, and inhibition of gene transfer by conjugation

Antibiotic-resistant bacteria (ARB) and their resistance genes (ARGs) are emerging environmental pollutants that pose great threats to human health. In this study, a novel strategy using plasma was developed to simultaneously remove antibiotic-resistant Escherichia coli (AR bio-56954 E. coli) and its ARGs, aiming to inhibit gene transfer by conjugation. Approximately 6.6 log AR bio-56954 E. coli was inactivated within 10 min plasma treatment, and the antibiotic resistance to tested antibiotics (tetracycline, gentamicin, and amoxicillin) significantly decreased. Reactive oxygen and nitrogen species (RONS) including •OH, ¹O₂, O₂•^-, NO₂^-, and NO₃^- contributed to ARB and ARGs elimination; their attacks led to destruction of cell membrane, accumulation of excessive intracellular reactive oxygen substances, deterioration of conformational structures of proteins, and destroy of nucleotide bases of DNA. As a result, the ARGs (tet(C), tet(W), blaTEM-1, aac(3)-II), and integron gene intI1), and conjugative transfer frequency of ARGs significantly decreased after plasma treatment. The results demonstrated that plasma has great prospective application in removing ARB and ARGs in water, inhibiting gene transfer by conjugation.

Managing and treating per- and polyfluoroalkyl substances (PFAS) in membrane concentrates

Per- and polyfluoroalkyl substances (PFAS), which are present in many waters, have detrimental impacts on human health and the environment. Reverse osmosis (RO) and nanofiltration (NF) have shown excellent PFAS separation performance in water treatment; however, these membrane systems do not destroy PFAS but produce concentrated residual streams that need to be managed. Complete destruction of PFAS in RO and NF concentrate streams is ideal, but long-term sequestration strategies are also employed. Because no single technology is adequate for all situations, a range of processes are reviewed here that hold promise as components of treatment schemes for PFAS-laden membrane system concentrates. Attention is also given to relevant concentration processes because it is beneficial to reduce concentrate volume prior to PFAS destruction or sequestration. Given the costs and challenges of managing PFAS in membrane concentrates, it is critical to evaluate both established and emerging technologies in selecting processes for immediate use and continued research.

MODERN PLASMA-BASED DESORPTION/IONIZATION: FROM ATOMS AND MOLECULES TO CHEMICAL SYNTHESIS

Since the first mass spectrometry (MS) experiments were conducted by Thomson and Aston, plasmas have been used as ionization sources. Historically, plasma ion sources were used for these experiments because they were one of the few known sources of gas-phase ions at the time and they were relatively simple to setup and operate. Since then, developments in plasma ionization have continued to inform and motivate advances in other areas of MS. For example, plasma-desorption MS demonstrated ionization of large peptides and polymers more than 10 years before the first descriptions of electrospray ionization (ESI) and matrix-assisted laser desorption/ionization (MALDI). As a result, significant effort was placed on development of ionization approaches, mass analysis, and detection approaches for very large molecules: even before the advent of ESI and MALDI. Since then, new analytical challenges and opportunities in plasma ionization have arisen. In this review, the emerging trends in plasma-based ionization for several areas of MS will be discussed, including molecular ionization, elemental ionization, hybrid elemental and molecular ion sources, and unique chemical transformations. © 2020 John Wiley & Sons Ltd. Mass Spec Rev.

Structural and Optical Sensing Properties of Nonthermal Atmospheric Plasma-Synthesized Polyethylene Glycol-Functionalized Gold Nanoparticles

Polyethylene glycol-functionalized gold nanoparticles (Au@PEG NPs) were prepared by a simple plasma-assisted method without additional reducing chemicals. After irradiating tetrachloroauric acid (HAuCl₄) and polyethylene glycol (PEG) in aqueous medium with an argon plasma jet, the gold precursor transformed into an Au@PEG NP colloid that exhibited surface plasma resonance at 530 nm. When the plasma jet entered the water, additional reactive species were induced through interactions between plasma-generated reactive species and aqueous media. Interaction of the gold precursor with the plasma-activated medium allowed the synthesis of gold nanoparticles (AuNPs) without reductants. The plasma-synthesized Au@PEG NPs had a quasi-spherical shape with an average particle diameter of 32.5 nm. The addition of PEG not only helped to stabilize the AuNPs but also increased the number of AuNPs. Au@PEG NP-loaded paper (AuNP-paper) was able to detect the degradation of rhodamine B, therefore, indicating that AuNP-paper can act as a surface-enhanced Raman scattering platform. Dye degradation by plasma treatment was investigated by optical absorption and Raman spectroscopy. The method proposed for the fabrication of Au@PEG NPs is rapid, low-cost, and environment-friendly and will facilitate the application of plasma-synthesized nanomaterials in sensors.

Degradation of aqueous atrazine using persulfate activated by electrochemical plasma coupling with microbubbles: removal mechanisms and potential applications

Persulfate (PS) activated by dielectric barrier discharge (DBD) integrated with microbubbles (MBs) was designed to decompose atrazine (ATZ) from aqueous solutions. The degradation efficiency reached 89% at a discharge power of 85W, a PS concentration of 1mM, and a air flow rate of 30mL/min after 75min treatment. Heat caused by DBD favoured ATZ removal. Besides, the effect of PS dosage, discharge power and initial pH values on ATZ removal was evaluated. The calculated energy yield revealed that it was economical and promising to treat 1L of ATZ-wastewaters. The existence of SO₄^2-, Cl^-, CO₃^2- and HCO₃^- lead to negative effects, while positive effect was observed when the presence of MBs and humic acid. The identification results of radicals and degradation intermediates suggested that multiple synergistic effects (such as heat, e_aq^- and H•) activated PS, and ¹O₂/reactive nitrogen species, •OH and SO₄^-• with contributions of 18%, 26%, and 29%, were main species attacking ATZ. ATZ degradation pathways including olefination, alkylic-oxidation, dealkylation, and dechlorination were proposed. An environment-friendly and a novel method for enhancing the PS-activation and ATZ-decomposition was provided, which fully utilised the electric-chemical conversion of DBD and high mass transfer efficiency of MBs.

Effect of plasma polarity on the synthesis of graphene quantum dots by atmospheric-pressure microplasmas

The aim of this study is to optimize the production of colloidal graphene quantum dots (GQD) in an aqueous solution containing sodium dodecyl sulfate (SDS) treated by an argon microplasma jet operated in open ambient air. The plasma has been investigated by optical emission spectroscopy and electrical measurements, and the produced GQDs have been studied by Raman spectroscopy, photoluminescence, UV-visible absorption, transmission electron microscopy and atomic force microscopy. We mainly focus on the influence of the polarity of the voltage applied to generate the microplasma. Although the deposited power is higher when using a positive polarity, the energy efficiency is also higher thanks to a faster synthesis rate. To understand the underlying mechanisms, we reproduced the experiments with the addition of [Formula: see text] in the aqueous solution. Results show that the GQD synthesis operates in two steps with SDS fragmentation followed by an electrolysis-related process. We demonstrate that the positive polarity performs better due to higher fragmentation rate.

Mechanism of Aqueous Carbon Dioxide Reduction by the Solvated Electron

Aqueous solvated electron (e_aq^-), a key species in radiation and plasma chemistry, can efficiently reduce CO₂ in a potential green chemistry application. Here, the mechanism of this reaction is unravelled by condensed-phase molecular dynamics based on the correlated wave function and an accurate density functional theory (DFT) approximation. Here, we design and apply the holistic protocol for solvated electron's reactions encompassing all relevant reaction stages starting from diffusion. The carbon dioxide reduction proceeds via a cavity intermediate, which is separated from the product (CO₂^-) by an energy barrier due to the bending of CO₂ and the corresponding solvent reorganization energy. The formation of the intermediate is caused by solvated electron's diffusion, whereas the intermediate transformation to CO₂^- is triggered by hydrogen bond breaking in the second solvation shell of the solvated electron. This picture of an activation-controlled e_aq^- reaction is very different from both rapid barrierless electron transfer and proton-coupled electron transfer, where key transformations are caused by proton migration.

Dynamics of solvated electrons during femtosecond laser-induced plasma generation in water

We studied the dynamics of solvated electrons in the early stage of plasma generation in water induced with an intense femtosecond laser pulse. According to the decay kinetics of solvated electrons, a fast recombination process of solvated electrons (geminate recombination) occurred with a more prolonged lifetime (500 ps to 1 ns) than that observed in previous pulse photolysis studies (10-100 ps). This unusually longer lifetime is attributed to additional production of solvated electrons due to abundant free electrons generated with the laser-induced plasma, implying significant influence of free electrons on the dynamics of solvated electrons.

Viscous droplet in nonthermal plasma: Instability, fingering process, and droplet fragmentation

The interaction of dielectric barrier discharge plasma and silicone-oil liquid droplet in a Hele-Shaw cell was investigated experimentally employing synchronized optical and electrical time-resolved measurements. Temporal development of the destabilization, stretching, and fragmentation of the plasma-liquid interface was studied for the whole event lifespan. The perturbation wavelength and temporal development of fingering speed, plasma-liquid interface length, mean transferred charge, and fractal dimension of the pattern were determined. Recorded changes in the dissipated mean power show a strong correlation to subsequent stretching of the interface, opening new methodological possibilities for future investigations. Our extensive parametric study shows that oil viscosity and applied voltage amplitude both have a significant impact on the interface evolution. Notably, at relatively high voltages the destabilized interface featured properties noticeably diverging from the theoretical prediction of a known model. We propose an explanation based on the change of the liquid viscosity with increased heating at high applied voltage amplitudes.

Plasma Enhanced Wet Chemical Surface Activation of TiO2 for the Synthesis of High Performance Photocatalytic Au/TiO2 Nanocomposites

To enhance the effectiveness of TiO2 as a photocatalyst, it was believed that the drawbacks of the large bandgap and the rapid electron-hole recombination can be overcome by coupling TiO2 with plasmonic metal nanoparticles. The incorporation of the nanoparticles onto the TiO2 surface requires a suitable procedure to achieve the proper particle adhesion. In this work, we propose a simple, clean, and effective surface activation of TiO2 using plasma enhanced wet chemical surface treatment. Under only 5 min of plasma treatment in a 3% NH3/3% H2O2 solution, gold nanoparticles were found better adhered onto the TiO2 surface. Hence, the methylene blue degradation rate of the Au/TiO2 under sunlight treated was improved by a factor of 3.25 times in comparison to non-treated Au/TiO2 and by 13 times in comparison to the bare rutile TiO2.

Effects of Atmospheric Plasma Corona Discharges on Soil Bacteria Viability

Crop contamination by soil-borne pathogenic microorganisms often leads to serious infection outbreaks. Plant protection requires disinfection of agricultural lands. The chemical and the physical disinfection procedures have several disadvantages, including an irreversible change in the soil ecosystem. Plasma, the "fourth state of matter" is defined as an ionized gas containing an equal number of negatively and positively charged particles. Cold-plasma technology with air or oxygen as the working gas generates reactive oxygen species, which are found to efficiently eradicate bacteria. In this study, we examined the effect of atmospheric plasma corona discharges on soil bacteria viability. Soil that was exposed to plasma for 60 s resulted in bacterial reduction by two orders of magnitude, from 1.1 × 10⁵ to 2.3 × 10³ cells g^-1 soil. Exposure for a longer period of 5 min did not lead to further significant reduction in bacterial concentration (a final reduction of only 2.5 orders of magnitude). The bacterial viability was evaluated using a colorimetric assay based on the bacterial hydrogenases immediately after exposure and at selected times during 24 h. The result showed no recovery in the bacterial viability. Plasma discharged directly on bacteria that were isolated from the soil resulted in a reduction by four orders of magnitude in the bacterial concentration compared to untreated isolated bacteria: 2.6 × 10^-3 and 1.7 × 10^-7, respectively. The plasma-resistant bacteria were found to be related to the taxonomic phylum Firmicutes (98.5%) and comprised the taxonomic orders Bacillales (95%) and Clostridiales (2%). To our knowledge, this is the first study of soil bacteria eradication using plasma corona discharges.

Bactericidal Silver Nanoparticles by Atmospheric Pressure Solution Plasma Processing

Silver nanoparticles have applications in plasmonics, medicine, catalysis and electronics. We report a simple, cost-effective, facile and reproducible technique to synthesise silver nanoparticles via plasma-induced non-equilibrium liquid chemistry with the absence of a chemical reducing agent. Silver nanoparticles with tuneable sizes from 5.4 to 17.8 nm are synthesised and characterised using Transmission Electron Microscopy (TEM) and other analytic techniques. A mechanism for silver nanoparticle formation is also proposed. The antibacterial activity of the silver nanoparticles was investigated with gram-positive and gram-negative bacteria. The inhibition of both bacteria types was observed. This is a promising alternative method for the instant synthesis of silver nanoparticles, instead of the conventional chemical reduction route, for numerous applications.

Chemical Analysis of Secondary Electron Emission from a Water Cathode at the Interface with a Nonthermal Plasma

When a nonthermal plasma and a liquid form part of the same circuit, the liquid may function as a cathode, in which case electrons are emitted from the liquid into the gas to sustain the plasma. As opposed to solid electrodes, the mechanism of this emission has not been established for a liquid, even though various theories have attempted to explain it via chemical processes in the liquid phase. In this work, we tested the effects of the interfacial chemistry on electron emission from water, including the role of pH as well as the hydroxyl radical, the hydrogen atom, the solvated electron, and the presolvated electron; it was found that none of these species are critical to sustain the plasma. We propose an emission mechanism where electrons, generated from ionized water molecules in the uppermost monolayers of solution, are emitted into the plasma directly from the conduction band of the water.

On a heavy path – determining cold plasma-derived short-lived species chemistry using isotopic labelling

Cold atmospheric plasmas (CAPs) are promising medical tools and are currently applied in dermatology and epithelial cancers. While understanding of the biomedical effects is already substantial, knowledge on the contribution of individual ROS and RNS and the mode of activation of biochemical pathways is insufficient. Especially the formation and transport of short-lived reactive species in liquids remain elusive, a situation shared with other approaches involving redox processes such as photodynamic therapy. Here, the contribution of plasma-generated reactive oxygen species (ROS) in plasma liquid chemistry was determined by labeling these via admixing heavy oxygen ¹⁸O₂ to the feed gas or by using heavy water H₂¹⁸O as a solvent for the bait molecule. The inclusion of heavy or light oxygen atoms by the labeled ROS into the different cysteine products was determined by mass spectrometry. While products like cysteine sulfonic acid incorporated nearly exclusively gas phase-derived oxygen species (atomic oxygen and/or singlet oxygen), a significant contribution of liquid phase-derived species (OH radicals) was observed for cysteine-S-sulfonate. The role, origin, and reaction mechanisms of short-lived species, namely hydroxyl radicals, singlet oxygen, and atomic oxygen, are discussed. Interactions of these species both with the target cysteine molecule as well as the interphase and the liquid bulk are taken into consideration to shed light onto several reaction pathways resulting in observed isotopic oxygen incorporation. These studies give valuable insight into underlying plasma–liquid interaction processes and are a first step to understand these interaction processes between the gas and liquid phase on a molecular level.

Cold atmospheric plasmas (CAPs) are promising medical tools producing short-lived reactive species.

Microplasma assisted synthesis of gold nanoparticle/graphene oxide nanocomposites and their potential application in SERS sensing

This is the first study on the deployment of direct current atmospheric pressure microplasma technique for the single step synthesis of gold nanoparticle/graphene oxide (AuNP/GO) nanocomposites. The nanocomposites were characterized using ultraviolet-visible spectroscopy (UV-vis), x-ray diffraction and x-ray photoelectron spectroscopy and their formation mechanisms have been discussed in detail. Our AuNP/GO nanocomposites are highly biocompatible and have demonstrated surface enhanced Raman scattering (SERS) properties as compared to pure AuNPs and pure GO. Their potential as SERS substrate has been further demonstrated using probe molecules (methylene blue) at different concentrations.

Atmospheric Plasma Meets Cell: Plasma Tailoring by Living Cells

The applications of the cold atmospheric plasma jet (CAPJ) in cancer treatment have been investigated for over a decade, focused on the effect that the CAPJ creates on cancer cells. Here we report for the first time on the impact that cells have on the CAPJ during treatment. To better understand these CAPJ-cell interactions, we analyzed the CAPJ behaviors in the presence of several normal and cancer cell lines and investigated the CAPJ selectivity. A more in-depth study of plasma self-organization patterns utilizing a model which contains a combination of normal and cancer cells reveals that the cells' capacitance can be an important predictor of plasma jet behavior. Cancer cells can direct the jet either toward or away from normal cells, which depends on the boundary condition behind the cell colony. Both experimental and theoretical results show that a grounded copper board beneath the cell-culture dish leads to opposite CPAJ behaviors compared with a floating boundary condition. In conclusion, our findings indicate that plasma can be self-adaptive toward cancer cells, and such a feature can be manipulated. Therefore, using the permittivity difference among cell lines may help us focus plasmas upon cancer cells at the vicinity of normal tissues and maximize the selectivity of plasma treatments.

Biological and medical applications of plasma-activated media, water and solutions

Non-thermal atmospheric pressure plasma has been proposed as a new tool for various biological and medical applications. Plasma in close proximity to cell culture media or water creates reactive oxygen and nitrogen species containing solutions known as plasma-activated media (PAM) or plasma-activated water (PAW) - the latter even displays acidification. These plasma-treated solutions remain stable for several days with respect to the storage temperature. Recently, PAM and PAW have been widely studied for many biomedical applications. Here, we reviewed promising reports demonstrating plasma-liquid interaction chemistry and the application of PAM or PAW as an anti-cancer, anti-metastatic, antimicrobial, regenerative medicine for blood coagulation and even as a dental treatment agent. We also discuss the role of PAM on cancer initiation cells (spheroids or cancer stem cells), on the epithelial mesenchymal transition (EMT), and when used for metastasis inhibition considering its anticancer effects. The roles of PAW in controlling plant disease, seed decontamination, seed germination and plant growth are also considered in this review. Finally, we emphasize the future prospects of PAM, PAW or plasma-activated solutions in biomedical applications with a discussion of the mechanisms and the stability and safety issues in relation to humans.