High-quality bulk hybrid perovskite single crystals within minutes by inverse temperature crystallization

Microscopic Mechanisms, Morphology, and Defect Formation in the Thermally Activated Crystallization of Methylammonium Lead Iodide

In this study, we unravel the atomistic mechanisms that govern the crystallization process of methylammonium lead iodide through the application of microsecond time scale molecular dynamics simulations.The findings indicate that methylammonium iodide (MAI) and lead iodide (PbI2) precursors exhibit a propensity to aggregate into a disordered film, which ultimately undergoes a thermally activated disorder-to-order transformation to achieve crystallization. Notably, the crystal evolution during the annealing process reveals morphological characteristics consistent with the Straski-Krastanov growth mode. The temperature dependence of the crystal growth rate demonstrates an activation energy of 0.37 eV, which may be ascribed to the energy required to dissociate defective Pb-I bonds and facilitate Pb diffusion. Finally, the mechanisms underlying the spontaneous generation of lead vacancies are examined, suggesting a kinetic origin for such optically active defects. In principle, the latter suggests the potential for reducing their concentration through optimization of the growth parameters.

Discovery of Perovskite Cosolvency and Undoped FAPbI3 Single-Crystal Solar Cells Fabricated in Ambient Air

We report the cosolvency effect of formamidinium lead triiodide (FAPbI3) in a mixture of γ-butyrolactone (GBL) and 2-methoxyethanol (2ME), a phenomenon where FAPbI3 shows higher solubility in the solvent blend than in either alone. We found that FAPbI3 exhibits 10× higher solubility in 30% 2ME in GBL than in 2ME alone and 40% higher solubility than in GBL alone at 90 °C. This enhanced solubility is attributed to the disruption of the hydrogen bonding network within 2ME, allowing its hydroxyl and ether groups to interact more freely with the solute. Leveraging this phenomenon, we grew phase-stable α-FAPbI3 thin single crystals under ambient air conditions with no doping. Compared to conventional cesium-doped FAPbI3, the undoped FAPbI3 single-crystal films exhibited lower defect densities and enhanced charge retention and transfer while also avoiding phase segregation linked to cesium incorporation. Solar cells fabricated with these ambient-air-grown single-crystal films achieved an efficiency of 21.56% (17.72% for cesium-doped FAPbI3), retaining 90% of performance after six months of storage. These findings advance our understanding of perovskite solubility in solvent blends and offer an efficient pathway for producing stable, high-efficiency FAPbI3 single-crystal solar cells through ambient air fabrication, overcoming the limitations of doping.

Monosolvent system for high-purity lead-free perovskite precursors scalable synthesis based on solubility differences

Metal halide perovskites (MHPs) are promising materials for various optoelectronic applications due to their unique properties. However, the presence of lead (Pb) in MHPs raises environmental and health concerns, prompting the search for lead-free alternatives. This study introduces a universal strategy for synthesizing high-purity lead-free perovskite precursors through a methanol monosolvent system that utilizes solubility differences. The synthesis method is scalable and universal, applicable to five lead-free perovskites such as Cs2SnCl6, Cs2TeCl6, Cs3Sb2Cl9, Cs2ZnCl4, and Cs2SnBr6, all maintaining high structural and compositional integrity with purities exceeding 99.985 %. The Cs2SnCl6 perovskite precursors achieve a high yield of 91.7 %. The synthesized Cs2SnCl6 perovskite exhibits superior electron mobility and lower baseline resistance when incorporated into gas sensors, demonstrating a high response (1.98 at 20 ppm) for dimethyl carbonate (DMC) detection due to its high purity. The simplicity and effectiveness of this one-step synthesis method offer a significant advancement for the production of high-quality perovskite materials for commercial applications in sensors and optoelectronics.

Graphite-Based Localized Heating Technique for Growing Large Area Methylammonium Lead Bromide Single Crystalline Perovskite Wafers and Their Charge Transfer Characteristics

Development of a reproducible technique to grow large area single crystalline perovskite wafers is an open research gap in the field of single crystalline perovskite solar cells. A graphite-based localized heating technique for growing large area methylammonium lead bromide (CH3NH3PbBr3; MAPBr) single crystalline thin film (SCTF) on different buffer layers, such as glass/indium doped tin oxide (ITO), glass/ITO/poly(triaryl amine) (PTAA), and glancing angle deposition (GLAD) coated glass/ITO/TiO2 substrates is reported, and their charge transport properties are discussed. It is observed that the localized heating technique can confine the supersaturation of the precursor mainly to the center of the substrate, leading to a restricted number of nucleations within a specific area on the substrate. Here, such 2-3 seed crystals obtained initially are allowed to grow to a larger size of up to 65 mm2. The X-ray diffraction (XRD) analysis indicated that the large area SCTF is an actual single crystal and not a heterogeneous group of small crystals merged together with a crystallinity index (CI) of 92.60 ± 0.11% which was comparable to that of the bulk single crystal (97.74 ± 0.47%). The atomic force microscopy (AFM) image depicted a smooth SCTF surface (R a = 4.37 ± 0.01 nm), and the wave-like pattern is attributed to the substrate morphology, implying that the topography of the substrate plays a crucial role in obtaining a planar SCTF. The XRD, UV-visible, photoluminescence (PL), Raman, and FTIR spectra analyses revealed that the large area SCTF is phase pure and free of residual impurities. The charge injection characteristics of the SCTFs grown on different buffer layers were investigated using PL emission (PLE) and PL decay analyses. The decrease in the PLE intensity for the SCTFs grown on PTAA and TiO2 substrates implied exciton quenching behavior, indicating the injection of the photogenerated charge carriers into the charge transfer layers (CTLs). The decrease of the fast decay component from τ1 = 4.77 ± 0.18 ns for glass to τ1 = 3.32 ± 0.07 ns for TiO2 and τ1 = 3.15 ± 0.33 ns for PTAA is ascribed to the interfacial recombination of the charges accumulated at the CTL/perovskite interface. These results propose that the localized heating technique can be employed for growing large area single crystalline perovskite wafers for optoelectronic and photovoltaic device applications.

Tunable Polariton Rabi Oscillation in Phase-Changing Perovskite Microcavities

Exciton-polaritons are composite quasiparticles hybridized between excitons and photons, which are very promising to develop quantum information devices such as entangled photon pair sources and polariton qubit devices by utilizing the fascinating properties of strong nonlinearity, Bose-Einstein condensation, and superfluidity. Organic-inorganic hybrid lead halide perovskites have attracted much interest in cavity quantum electrodynamics due to their excellent excitonic properties, including strong exciton binding energy and high oscillation strength. Here, tunable Rabi oscillation of exciton-polaritons in the lead halide perovskite microcavity is demonstrated, which experiences a phase transition between orthorhombic, tetragonal, and cubic phases by varying the temperature. Over the phase transition, the Rabi frequency is probed by tracing the dispersion relation of the exciton-polaritons using Fourier plane spectroscopy. Due to the emergence of ferroelectricity in the tetragonal phase of the perovskites, the Rabi splitting can be tuned by ≈20%, while the corresponding exciton oscillator strength is varied by ≈44%. These results provide insight into novel functionalities of polariton devices by utilizing ferroic semiconductors, which can facilitate the development of tunable quantum devices.

Surface chemistry-engineered perovskite quantum dot photovoltaics

The discovery and synthesis of colloidal quantum dots (QDs) was awarded the Nobel Prize in Chemistry in 2023. Recently, the development of bulk metal halide perovskite semiconductors has generated intense interest in their corresponding perovskite QDs. QDs, more broadly known as nanocrystals, constitute a new class of materials that differ from both molecular and bulk materials. They have rapidly advanced to the forefront of optoelectronic applications owing to their unique size-, composition-, surface- and process-dependent optoelectronic properties. More importantly, their ultrahigh surface-area-to-volume ratio enables various surface chemistry engineering strategies to tune and optimize their optoelectronic properties. Finally, three-dimensional confined QDs, offering nearly perfect photoluminescent quantum yield, slow hot-carrier cooling time, especially their colloidal synthesis and processing using industrially friendly solvents, have revolutionized the fields of electronics, photonics, and optoelectronics. Particularly, in emerging perovskite QD-based PVs, the advancement of surface chemistry has boosted the record power conversion efficiency (PCE) to 19.1% within a five-year period, surpassing all other colloidal QD photovoltaics (PVs). Given the rapid enhancement of device performances, perovskite QD PVs have attracted significant attention. Further study of semiconducting perovskite QDs will lead to advanced surface structures, a deeper understanding of halide perovskites, and enhanced PCE. In this review article, we comprehensively summarize and discuss the emerging perovskite QD PVs, providing insights into the impact of surface chemical design on their electronic coupling, dispersibility, stability and defect passivation. The limitations of current perovskite QDs mainly arise from their "soft" ionic nature and dynamic surface equilibrium, which lead to difficulties in the large-scale synthesis of monodispersed perovskite QDs and conductive inks for high-throughput printing techniques. We present that the development of surface chemistry is becoming a platform for further improving PCE, aiming to reach the 20% milestone. Additionally, we discuss integrating artificial intelligence to facilitate the mass-production of perovskite QDs for large-area, low-cost PV technology, which could help address significant energy challenges.

Exploring Lead-Free (Guanidinium)3Bi2Br9 Perovskite-Type Crystal toward X-Ray Detection with an Ultralow Detection Limit

Lead-free bismuth halogen perovskites have emerged as a promising candidate for high-performance X-ray detection, owing to their unique properties of bulk resistivity, significant X-ray absorption capabilities and diminished ion migration. Herein, using the facile low-temperature solution method, we obtained a large-size single crystal of (guanidinium)3Bi2Br9 (GBB), which adopts a zero-dimensional (0D) inorganic perovskite-like framework. The as-grown crystals show high resistivity (3.51×1012 Ω cm), low trap density (1.14×1010 cm-3) and large carrier mobility-lifetime product (μτ=1.13×10-3 cm2 V-1) under X-ray irradiation. Strikingly, the X-ray detectors fabricated on GBB single crystals exhibit notable performances including low dark current drift, high sensitivity of ~1645.7 μC Gyair -1 cm-2, and ultralow detection limit of ~0.85 nGyair s-1. This detection limit is among the lowest level for the reported 0D perovskite X-ray detectors. This study illuminates the prospective research into novel lead-free hybrid perovskites for the advancement of high-performance detectors of irradiation.

MAPbX3 Perovskite Single Crystals for Advanced Optoelectronic Applications: Progress, Challenges, and Perspective

Perovskite single crystals have garnered significant attention due to their impressive properties in optoelectronic applications, including long carrier diffusion lengths, low trap-state densities, and enhanced stability. Methylamino lead halide perovskite (MAPbX3, where X is a halogen such as Cl, Br, or I) is a notable example of a metal halide perovskite with desirable properties and ideal cubic perovskites with a tolerance factor between 0.9 and 1.0. MAPbX3 has adjustable bandgap, high thermal and chemical stability, and excellent light absorption capacity. Here the unique characteristics of MAPbX3, including molecular structure, optical absorption properties, and carrier transport of MAPbX3 single crystals are summarized. Universal growth technologies for MAPbX3 single crystals, including inverse temperature crystallization, anti-solvent evaporation crystallization, solvent evaporation method, and single-crystalline thin film, including epitaxial method and space limiting method, are briefly introduced. Additionally, a comprehensive review of MAPbX3 single crystals in various optoelectronic device applications, including photodetectors, X-ray detectors, light-emitting diodes, lasers, and solar cells is mainly discussed. Finally, the current challenges and future prospects of the large-scale preparation and growth of MAPbX3 single crystals are put forward. With the continuous progress of photoelectric technology, more innovative photoelectric applications in the future are expected to bring more convenience and progress.

Colloidally uniform single-crystal precursors enable uniform FAPbI3 films for efficient perovskite submodules

With the unprecedented research development on lead halide perovskite photovoltaics, scaling up fabrication while comprehensively understanding the properties of cost-effective and highly uniform precursor films has become critical for their practical application. When enlarging the device area, good precursor purity serves as the first step in ensuring the uniformity of the perovskite film. Chemical purity and colloidal uniformity in the precursor solution both play important roles in dictating film uniformity and defect density. Here, for the first time, we explored the colloidal behavior of FAPbI3 precursors using different preparatory materials of varied costs but with similar metal purity. As the colloidal size of regular PbI2 + FAI powder precursors increased compared to that of PbI2 colloids, the FAPbI3 single-crystal precursor synthesized from low-purity chemicals exhibited a generally smaller and more uniform colloidal size, which yielded perovskite films with improved uniformity and reduced defect density at lower cost. The colloidally uniform single-crystal precursors led to photovoltaics with higher power conversion efficiency and better long-term operational stability. More importantly, the uniformity in the precursor and film was found to be beneficial for large-area fabrication, where the scaling-up production of 30 cm × 30 cm perovskite submodules based on single-crystal precursors achieved an impressive 20.7% efficiency.

A-site composition tuning in methylammonium-based metal halide perovskite colloidal nanocrystals

Utilizing the soft-lattice nature of metal halide perovskites, we employ post-synthetic cross-ion exchange to synthesize a series of narrow band-gap colloidal nanocrystals of methylammonium-based lead iodide solid solutions of composition FAxMA1-xPbI3, as well as those of triple-cation composition CsxFAyMA1-x-yPbI3 (TCPbI3). The ability to finely tune the compositions not only helps in tailoring the optical properties in the near-infrared region, but also improves the stability of these colloidal nanocrystals towards moisture, which has been demonstrated as compared to their bulk counterparts. The thermal stability of these solid solutions is also comparable to that of the bulk, as evidenced by thermogravimetric studies. This study helps in expanding the composition space of stable 3D lead halide perovskites with band gaps suitable and relevant for photovoltaic applications.

Idealizing Air-Processed Perovskite Film Competitive by Surface Lattice Etching-Reconstruction for High-Efficiency Solar Cells

Air-processed perovskite solar cells are desirable for the large-scale manufacturing application in the future, yet the presence of moisture and oxygen goes against perovskite crystallization and deteriorates phase stabilization, leading to the formation of substantial defective nano-impurities, especially on the vulnerable surface. Here, we propose a strategy to simultaneously remove superficial defect layer and solidify the surface by soaking air-fabricated perovskite film into low-polar organic esters at elevated temperature to trigger an in situ dynamic surface lattice disassemble and reconstruction process. Molecular dynamics simulations and experimental results indicate that the inorganic CsPbI2Br perovskite is first dissolved and then the Br-rich phase is recrystallized at solid-liquid interface owing to the balance between weak solubility and high-temperature induced annealing process, thus hardening the soft surface and releasing the lattice tensile stress, which benefits the minimization of interfacial recombination and improvement of the structural stability. As a result, we prepare a carbon-based CsPbI2Br device in complete air without precise control on humidity, achieving a champion efficiency of 15.37 % with excellent resistance to harsh attackers. This method offers a promising avenue for overcoming the limit of processing conditions on advancing perovskite-based optoelectronic devices.

High-Performing Direct X-Ray Detection Made of One-Dimensional Perovskite-Like (TMHD)SbBr5 Single Crystal With Anisotropic Response

3D and 2D organic hybrid perovskites, as well as double perovskites, have demonstrated their suitability for direct X-ray detection. However, the sensitivity and stability of 3D perovskite X-ray detectors are currently being hindered by the existing constraints on ion movement. Therefore, there is an immediate need to develop X-ray detectors that are both highly sensitive and stable while also being environmentally friendly. The novel low-dimensional perovskites demonstrate exceptional inherent stability and effectively mitigate ion migration, thereby showcasing their remarkable photoelectric performance. Inspired by this, a solution crystallization method is employed to synthesize novel single crystals (SCs) of one dimensional (1D) (TMHD)SbBr5. The dimensions of the chained (TMHD)SbBr5 SC are 13 × 1.3 × 1.2 mm3 in size. The device based on a perovskite chain (TMHD)SbBr5 exhibits unique anisotropic X-ray detection performance with a sensitivity of 62.8 and 30.5 µC Gyair -1cm-2 in the parallel and perpendicular orientations, respectively. It can lead to the directional movement of ions, resulting in large carrier mobility under the action of electric fields, and effectively increase the sensitivity to X-ray detection.

Photoinduced Fröhlich Interaction-Driven Distinct Electron- and Hole-Polaron Behaviors in Hybrid Organic-Inorganic Perovskites by Ultrafast Terahertz Probes

The formation of large polarons resulting from the Fröhlich coupling of photogenerated carriers with the polarized crystal lattice is considered crucial in shaping the outstanding optoelectronic properties in hybrid organic-inorganic perovskite crystals. Until now, the initial polaron dynamics after photoexcitation have remained elusive in the hybrid perovskite system. Here, based on the terahertz time-domain spectroscopy and optical-pump terahertz probe, we access the nature of interplay between photoexcited unbound charge carriers and optical phonons in MAPbBr3 within the initial 5 ps after excitation and have demonstrated the simultaneous existence of both electron- and hole-polarons, together with the photogenerated carrier dynamic process. Two resonant peaks in the frequency-dependent photoconductivity are interpreted by the Drude-Smith-Lorentz model along with the ab initio excitation calculation, revealing that the electron-/hole-polaron is related to the vibration modes of the stretched/contracted Pb-Br bond. The red /blue shift of the corresponding peaks as the fingerprints of electron-/hole-polaron provides a channel for observing their dynamic behavior. Different from polarons with long lifetime (>300 ps) in single-crystalline grains, we observed in thin films the transient process from the formation to the dissociation of polarons occurring at timescales within ∼5 ps, resulting from the Mott phase transition for carriers at high concentrations. Moreover, the observation of the polaron dynamic process of the virtual state-assisted band gap transition (800 nm excitation) further reveals the competition of carriers cooling and polaron formation with photocarrier density. Our observations demonstrate a strategy for direct observation and manipulation of bipolar polaron transport in hybrid perovskites.

Zipper-Like Dynamic Switching of Coordination Bonds Gives a Polar Bimetallic Halide Toward Self-Driven X-Ray Detection

Polar molecular crystals hold a promise for controlling bulk physical properties originated in their unique switchable polarity via structural transformation. However, the mechanisms for switching polarization are mainly limited to displacive and disorder-order phase transitions, which rarely involve the reconstruction of chemical bonds. Here, we have switched and tuned electric polarization in a bimetallic halide, (Neopentylammonium)4AgBiBr8 (1), as verified by light-excited pyroelectric effect. Most notably, its Ag-Br coordination bonds show a zipper-like dynamic switching behavior from the 'locked' to 'unlocked' state, namely, reconstruction of chemical bonds. Coupling with the dynamic ordering of organic cations, this bond-switching transition makes a contribution to switchable polarization of 1. As expected, its polarity creates pyroelectric effect for self-driven X-ray detection with high sensitivity (3.8×103 μC Gy-1 cm-2) and low limit of detection (4.8 nGy s-1). This work on the bond-switching mechanism provides an avenue to design polar molecular candidate for smart optoelectronic devices.

Real-Time Structural Dynamics at the 3D/2D Perovskite Interface in CsPbBr3/PEA2PbBr4 Nano-heterostructures

Three-dimensional (3D) and two-dimensional (2D) perovskite hybrid systems, known for their exceptional optoelectronic properties and stability, are revolutionizing optoelectronic materials research. However, fundamental physics of the 3D/2D interfaces and their dynamics remain poorly understood. We use fluorescence microspectroscopy to study the photoluminescence (PL) properties of 3D/2D nano-heterostructures of CsPbBr3/PEA2PbBr4 formed by postgrowth self-assembly. The in situ PL spectra uncover the presence of new structural phases, quasi-2D PEA2Csn-1PbnBr3n+1 layers of varying n, at the 3D/2D interface and demonstrate their reversible restructuring under light excitation at room temperature. The restructuring is a result of layer-by-layer cation diffusion at the epitaxial interfaces, manifested as reversible spectral shifts occurring on a time scale of seconds. Such dynamics ultimately leads to optimized distribution of the quasi-2D phases in the system for efficient energy transfer from the 2D to the 3D phases. Our findings provide new insights into controlling energy flow in 3D/2D perovskites for next-generation optoelectronic devices.

Cost-Effective Synthesis Method: Toxic Solvent-Free Approach for Stable Mixed Cation Perovskite Powders in Photovoltaic Applications

Organometallic lead halide perovskite powders have gained widespread attention for their intriguing properties, showcasing remarkable performance in the optoelectronic applications. In this study, formamidinium lead iodide (α-FAPbI3) microcrystals (MCs) is synthesized using retrograde solubility-driven crystallization. Additionally, methylammonium lead bromide (MAPbBr3) and cesium lead iodide (δ-CsPbI3) MCs are prepared through a sonochemical process, employing low-grade PbX2 (X = I & Br) precursors and an eco-friendly green solvent (γ-Valerolactone). The study encompasses an analysis of the structural, optical, thermal, elemental, and morphological characteristics of FAPbI3, MAPbBr3, and CsPbI3 MCs. Upon analysing phase stability, a phase transition in FAPbI3 MCs is observed after 2 weeks. To address this issue, a powder-based mechanochemical method is employed to synthesize stable mixed cation perovskite powders (MCPs) by subjecting FAPbI3 and MAPbBr3 MCs with varying concentrations of CsPbI3. Furthermore, the performance of mixed cation perovskites are examined using the Solar Cell Capacitance Simulator (SCAPS-1D) software. The impact of cesium incorporation in the photovoltaic characteristics is elucidated. All mixed cation absorbers exhibited optimal device performance with a thickness ranging between 0.6-1.5 µm. It's worth noting that the MCPs exhibit impressive ambient stability, remaining structurally intact and retaining their properties without significant degradation for 70 days of ambient exposure.

Structural Reconfiguration via Alternating Cation Intercalation of Chiral Hybrid Perovskites for Efficient Self-Driven X-ray Detection

2D hybrid perovskites (HPs) have great potential for high-performance X-ray detection due to their strong radiation absorption and flexible structure. However, there remains a need to explore avenues for enhancing their detection capabilities. Optimizing the detection performance through modification of their structural properties presents a promising strategy. Herein, we explore the impact of modifying the organic spacer layer in two distinct 2D layered HPs, namely, Ruddlesden-Popper (R-MPA)2PbBr4 (R-1, R-MPA = methylphenethylammonium) and (R-MPA)EAPbBr4 (EA = ethylammonium) (R-2) with alternating cation intercalation (ACI), on their X-ray detection performance. The insertion of EA into R-2 results in a flatter inorganic skeleton, narrower spacing, and higher density compared to R-1. This structural modification effectively optimizes carrier transport and X-ray absorption in R-2, enhancing the X-ray detection performance. Notably, R-2 exhibits a polar structure with intrinsic spontaneous polarization, contributing to a bulk photovoltaic of 0.4 V. This feature enables R-2 single-crystal detectors to achieve self-driven X-ray detection with a low detection limit of 82.5 nGy s-1 under a 0 V bias. This work highlights the efficacy of the ACI strategy in structural modification and its significant effect on X-ray detection properties, providing insights for the design and optimization of new materials.

Intermediate-Controlled Synthesis of Quasi-2D (PEA)2MA4Pb5I16 in the 20-30% Relative Humidity Glovebox Environment for Fabricating Perovskite Solar Cells with 1 Month Durability in the Air

Herein, quasi-two-dimensional (Q-2D) (PEA)2MA4Pb5I16 (prepared by a two-step process) and hole transport layer of a solar cell were fabricated in a high relative humidity (25 ± 5%) environment. The PSC behavior of most Q-2D perovskites is worse than that of three-dimensional perovskites owing to the horizontal alignment of the innate characteristic organic plates on the substrate. Using hybrid immersion solvents (HISs), we have improved vertical alignment in an appropriate ratio to enhance the efficiency of charge transfer and the high coverage of the first priming layer (first step). The grazing incidence X-ray diffraction pattern of the optimized structures revealed a preferential orientation for the vertical alignment of (111), which improved the charge transfer in PSCs and micrometer-level grain size growth. The second step was processed in a high-humidity environment (50 ± 5%) (methylammonium iodide solution embedded), and Q-2D (PEA)2MA4Pb5I16 demonstrated distinct grain boundaries. The power conversion efficiency (PCE, 13.09%) of the champion device of the first priming layer prepared using the HIS system increased by >55% compared to the single-immersion solvent (8.3%). The PCE of the ion-modified ETL PSCs was 16.02% (CsF-3) and 14.58% (CsCl-3) and demonstrated 22 and 11% improvement, respectively. The ion-modified electron transport layer (ETL) was deposited in the air, which reduced the power consumption of preparing perovskite solar cells (PSCs). Finally, all Q-2D PSCs were stored in the air, and three PSCs (DMF/DMSO, CsF-3, and CsCl-3) using HIS exhibited long-term stability for 1 month maintaining 80-88% of PCE, demonstrating the importance of the HIS system to improve the first step of growth orientation, which enhances the stability and photovoltaic properties of PSCs.

Preparation Techniques for Perovskite Single Crystal Films: From Nucleation to Growth

Thickness-controllable perovskite single crystal films exhibit tremendous potential for various optoelectronic applications due to their capacity to leverage the relationship between diffusion length and absorption depth. However, the fabrication processes have suffered from difficulties in large-area production and poor quality with abundant surface defects. While post-treatments, such as passivation and polishing, can provide partial improvement in surface quality, the fundamental solution lies in the direct growth of high-quality single crystal films. In this work, we firstly summarize the basic principles of nucleation and growth phenomenon of crystalline materials. Advanced growth methods of perovskite single crystal films, including solution-based, vapor phase epitaxial growth, and top-down method, are discussed, highlighting their respective advantages and limitations. Finally, we also present future directions and the challenges that lie ahead in perovskite single crystal films.

In Situ Fabricated Perovskite Quantum Dots: From Materials to Applications

Due to the low formation enthalpy and high defect tolerance, in situ fabricated perovskite quantum dots offer advantages such as easy fabrication and superior optical properties. This paper reviews the methodologies, functional materials of in situ fabricated perovskite quantum dots, including polymer nanocomposites, quantum dots doped glasses, mesoporous nanocomposites, quantum dots-embedded single crystals, and electroluminescent films. This study further highlights the industrial breakthroughs of in situ fabricated perovskite quantum dots, especially the scale-up fabrication and stability enhancement. Finally, the fundamental challenges in developing perovskite quantum dots for industrial applications are discussed, with a focus on photoinduced degradation under high-intensity light irradiation, ion migration under electrical bias and thermal quenching at high temperature.

A-Site Cation Chemistry in Halide Perovskites

Metal halide perovskites are an important class of semiconductors now being implemented as photovoltaic absorbers and explored for light emission, among other device applications. The semiconducting properties of halide perovskites are deeply intertwined with their composition and structure. Specifically the symmetry, tilting, and distortions of the metal halide octahedra impact the band structure and other optoelectronic properties. In this review, we examine the various compositions of monovalent A-site cations in three-dimensional (3D) halide perovskites AMX3 (M = divalent metal; X = halide). We focus on how the A-site cation templates the inorganic metal-halide perovskite framework, resulting in changes in the crystal structure symmetry, as well as M-X bonding parameters, summarized in a comprehensive table of AMX3 structures. The A-site cation motion, effects of alloying, and 2D Ruddlesden-Popper perovskite structures with unique A-site cations are further overviewed. Correlations are shown between these A-site cation dominated structural parameters and the resulting optoelectronic properties such as band gap. This review should serve as a reference for the A-site cation structural chemistry of metal halide perovskites and inspire continued research into less explored metal halide perovskite compositions and structures.

Interfacial Engineering for Controlled Crystal Mosaicity in Single-Crystalline Perovskite Films

Organic-inorganic hybrid perovskites have attracted significant attention for optoelectronic applications due to their efficient photoconversion properties. However, grain boundaries and irregular crystal orientations in polycrystalline films remain issues. This study presents a method for producing crystalline-orientation-controlled perovskite single-crystal films using retarded solvent evaporation. It is shown that single-crystal films, grown via inverse temperature crystallization within a confined space, exhibit enhanced optoelectronic property. Using interfacial polymer layer, this method produces high-quality perovskite single-crystalline films with varying crystal orientations. Density functional theory calculations confirm favorable adsorption energies for (110) surfaces with methylammonium iodide and PbI2 terminations on poly(3-hexylthiophene), and stronger adsorption for (224) surfaces with I and methylammonium terminations on polystyrene, influenced by repulsive forces between the thiophene group and the perovskite surface. The correlation between charge transport characteristics and perovskite single-crystalline properties highlights potential advancements in perovskite optoelectronics, improving device performance and reliability.

Dynamics of Photoinduced Charge Carriers in Metal-Halide Perovskites

The measurement and description of the charge-carrier lifetime (τc) is crucial for the wide-ranging applications of lead-halide perovskites. We present time-resolved microwave-detected photoconductivity decay (TRMCD) measurements and a detailed analysis of the possible recombination mechanisms including trap-assisted, radiative, and Auger recombination. We prove that performing injection-dependent measurement is crucial in identifying the recombination mechanism. We present temperature and injection level dependent measurements in CsPbBr3, which is the most common inorganic lead-halide perovskite. In this material, we observe the dominance of charge-carrier trapping, which results in ultra-long charge-carrier lifetimes. Although charge trapping can limit the effectiveness of materials in photovoltaic applications, it also offers significant advantages for various alternative uses, including delayed and persistent photodetection, charge-trap memory, afterglow light-emitting diodes, quantum information storage, and photocatalytic activity.

Mapping Surface-Defect and Ions Migration in Mixed-Cation Perovskite Crystals

Single crystal perovskites have garnered significant attention as potential replacements for existing absorber layer materials. Despite the extensive investigations on their photoinduced charge-carriers dynamics, most of the time-resolved techniques focus on bulk properties, neglecting surface characteristic which plays a crucial role for their optoelectronic performance. Herein, 4D ultrafast scanning electron microscopy (4D-USEM) is utilized to probing the photogenerated carrier transport at the first few nanometers, alongside density functional theory (DFT) to track both defect centers and ions migration. Two compositions of mixed cation are investigated: FA0.6MA0.4PbI3 and FA0.4MA0.6PbI3, interestingly, the former displays a longer lifetime compared to the latter due the presence of a higher surface-defect centers. DFT calculations fully support that revealing samples with higher FA content have a lower energy barrier for iodide ions to migrate from the bulk to top layer, assisting in passivating surface vacancies, and a higher energy diffusion barrier to escape from surface to vacuum, resulting in fewer vacancies and longer-lived hole-electron pairs. These findings manifest the influence of cation selection on charge carrier transport and formation of defects, and emphasize the importance of understanding ion migrations role in controlling surface vacancies to assist engineering high-performance optoelectronic devices based on single crystal perovskites.

Nanometer-Resolved Mapping of Organic Cation Migration Behavior in Methylammonium Lead Halide Perovskites

The performance and stability of organic metal halide perovskite (OMHP) optoelectronic devices have been associated with ion migration. Understanding of nanoscale resolved organic cation migration mechanism would facilitate structure engineering and commercialization of OMHP. Here, we report a three-dimensional approach for in situ nanoscale infrared imaging of organic ion migration behavior in OMHPs, enabling to distinguish migrations along grain boundary and in crystal lattice. Our results reveal that organic cation migration along OMHP film surface and grain boundaries (GBs) occurs at lower biases than in crystal lattice. We visualize the transition of organic cation migration channels from GBs to volume upon increasing electric field. The temporal resolved results demonstrate the fast MA+ migration kinetics at GBs, which is comparable to diffusivity of halide ions. Our findings help understand the role of organic cations in the performance of OMHP devices, and the proposed approach holds broad applicability for revealing migration mechanisms of organic ions in OMHPs based optoelectronic devices.

Overcoming the EQE × Li-Fi Frequency Constraint by Modulating the PbS CQDs Distribution in Perovskite Film

Advanced photodetectors are crucial for high-fidelity optical communication. However, the tradeoff between high external quantum efficiency (EQE) and high light fidelity (Li-Fi) frequency often limits data transmission accuracy and timeliness. Here, we report a photodetector consisting of lead sulfide (PbS) colloidal quantum dots (CQDs) with near-infrared responsiveness and perovskite frameworks responsible for the charge transport to overcome the EQE × Li-Fi constraint. Optimizing the PbS CQDs distribution and trap depth in the perovskite layer enhances charge injection, achieving a device gain of 11892% for 1200 nm photons and a response frequency of 24 kHz at -2 V. The device exhibits a record EQE × Li-Fi frequency product of 106 Hz. We have applied the detector to near-infrared optical communications at a data transfer rate of 2000 bits per second (2 kbps) to demonstrate the advances in high fidelity, the device retains over 98% of the original waveform information in its output.

Cathodoluminescence of MAPbCl3 Halide Perovskite Single Crystal

Chloride perovskites are semiconductors with a near-ultraviolet bandgap that are promising for applications in optoelectronics and photonics. One of the most studied representatives of this family is the methylammonium lead chloride MAPbCl3 (MA+ = CH3NH3+). Low-temperature luminescence spectroscopy of this material demonstrates a complex emission structure. In this work, we have studied the cathodoluminescecne of the MAPbCl3 halide perovskite single crystal at 70 K. Excitation by an electron beam was used to localize different emitters: excitons, defect-related states, and inclusions, previously assigned to the material itself. Exciton luminescence is observed from an undamaged sample, while the defect band is emitted from regions with dislocations, growth defects, and crystal damage. Defect formation under electron beam irradiation was studied. It was found that MAPbCl3 is resistant to irradiation, which supports the defect tolerance of halide perovskites and paves the way for their electron-beam modification for applications.

Realizing Color Transitions for Three Copper (I) Cluster Organic-Inorganic Hybrid Materials by Adjusting Reaction Conditions

Copper iodide organic-inorganic hybrid materials have been favored by many researchers in the field of solid-state lighting (SSL) due to their structural diversity and optical adjustability. In this paper, three isomeric copper iodide cluster hybrid materials, Cu4I6(L)2(1), Cu5I4.5Cl2.5(L)2(2) and Cu5I7(L)2) (3) (L=1-(4-methylpyrimidin-2-yl)-1,4-diazabicyclo[2.2.2]octan-1-ium), were achieved by adjusting the reaction conditions. The crystal color transit from green, yellow to orange and the internal quantum yield (IQY) increase from 57 %-88 %. All three complexes have good thermal stability, good solution processability, and high quantum yield. And origin and mechanism of luminescence of complexes were further studied. This study can provide ideas and theoretical basis for the regulation of cuprous iodide cluster luminescent materials.

Physical Properties of an Efficient MAPbBr3/GaAs Hybrid Heterostructure for Visible/Near-Infrared Detectors

Semiconductor photodetectors can work only in specific material-dependent light wavelength ranges, connected with the bandgaps and absorption capabilities of the utilized semiconductors. This limitation has driven the development of hybrid devices that exceed the capabilities of individual materials. In this study, for the first time, a hybrid heterojunction photodetector based on methylammonium lead bromide (MAPbBr3) polycrystalline film deposited on gallium arsenide (GaAs) was presented, along with comprehensive morphological, structural, optical, and photoelectrical investigations. The MAPbBr3/GaAs heterojunction photodetector exhibited wide spectral responsivity, from 540 to 900 nm. The fabrication steps of the prototype device, including a new preparation recipe for the MAPbBr3 solution and spinning, will be disclosed and discussed. It will be shown that extending the soaking time and refining the precursor solution's stoichiometry may enhance surface coverage, adhesion to the GaAs, and film uniformity, as well as provide a new way to integrate MAPbBr3 on GaAs. Compared to the pristine MAPbBr3, the enhanced structural purity of the perovskite on GaAs was confirmed by X-ray Diffraction (XRD) upon optimization compared to the conventional glass substrate. Scanning Electron Microscopy (SEM) revealed the formation of microcube-like structures on the top of an otherwise continuous MAPbBr3 polycrystalline film, with increased grain size and reduced grain boundary effects pointed by Energy-Dispersive Spectroscopy (EDS) and cathodoluminescence (CL). Enhanced absorption was demonstrated in the visible range and broadened photoluminescence (PL) emission at room temperature, with traces of reduction in the orthorhombic tilting revealed by temperature-dependent PL. A reduced average carrier lifetime was reduced to 13.8 ns, revealed by time-resolved PL (TRPL). The dark current was typically around 8.8 × 10-8 A. Broad photoresponsivity between 540 and 875 nm reached a maximum of 3 mA/W and 16 mA/W, corresponding to a detectivity of 6 × 1010 and 1 × 1011 Jones at -1 V and 50 V, respectively. In case of on/off measurements, the rise and fall times were 0.40 s and 0.61 s or 0.62 s and 0.89 s for illumination, with 500 nm or 875 nm photons, respectively. A long-term stability test at room temperature in air confirmed the optical and structural stability of the proposed hybrid structure. This work provides insights into the physical mechanisms of new hybrid junctions for high-performance photodetectors.

Single Crystal Sn-Based Halide Perovskites

Sn-based halide perovskites are expected to be the best replacement for toxic lead-based counterparts, owing to their similar ionic radii and the optimal band gap for use in solar cells, as well as their versatile use in light-emitting diodes and photodetection applications. Concerns, however, exist about their stability under ambient conditions, an issue that is exacerbated in polycrystalline films because grain boundaries present large concentrations of defects and act as entrance points for oxygen and water, causing Sn oxidation. A current thriving research area in perovskite materials is the fabrication of perovskite single crystals, promising improved optoelectronic properties due to excellent uniformity, reduced defects, and the absence of grain boundaries. This review summarizes the most recent advances in the fabrication of single crystal Sn-based halide perovskites, with emphasis on synthesis methods, compositional engineering, and formation mechanisms, followed by a discussion of various challenges and appropriate strategies for improving their performance in optoelectronic applications.

Unprecedented Richness of Temperature- and Pressure-Induced Polymorphism in 1D Lead Iodide Perovskite

Inherent features of metal halide perovskites are their softness, complex lattice dynamics, and phase transitions spectacularly tuning their structures and properties. While the structural transformations are well described and classified in 3D perovskites, their 1D analogs are much less understood. Herein, both temperature- and pressure-dependent structural evolutions of a 1D AcaPbI3 perovskitoid incorporating acetamidinium (Aca) cation are examined. The study reveals the existence of nine phases of δ-AcaPbI3, which present the most diverse polymorphic collection among known perovskite materials. Interestingly, temperature- and pressure-triggered phase transitions in the 1D perovskotoid exhibit fundamentally different natures: the thermal transformations are mainly associated with the collective translations of rigid polyanionic units and ordering/disordering dynamics of Aca cations, while the compression primarily affects inorganic polymer chains. Moreover, in the 1-D chains featuring the face-sharing connection mode of the PbI6 octahedra the Pb···Pb distances are significantly shortened compared to the corner-sharing 3D perovskite frameworks, hence operating in the van der Waals territory. Strikingly, a good correlation is found between the Pb···Pb distances and the pressure evolution of the bandgap values in the δ-AcaPbI3, indicating that in 1D perovskitoid structures, the contacts between Pb2+ ions are one of the critical parameters determining their properties.

Moisture is not always bad: H2O accelerates the conversion of DMAPbI3 intermediate to CsPbI3 for boosting the efficiency of carbon-based perovskite solar cells to over 16

Inorganic CsPbI3 perovskite has exhibited great application potential in perovskite solar cells (PSCs) due to its suitable optical bandgap and high chemical stability. However, the perovskite phases of CsPbI3 are not stable at room temperature, where they transition to non-perovskite phases. Humidity or water has been thought to be the primary factor inducing this phase transition, which should be avoided throughout the procedure of film and device processing. Surprisingly, the present study indicates that preparing a precursor solution in humid air is beneficial to the growth of high-quality CsPbI3 perovskite to enhance device performance. It is demonstrated that the incorporation of H2O in the precursor solution from humid air or by intentional addition significantly changes the composition of coordination compounds and increases the amount of low iodine coordination complexes. As a result, the crystallization of dimethylammonium lead iodide (DMAPbI3) intermediate is suppressed well, which accelerates its subsequent conversion to CsPbI3 perovskite. Consequently, an oriented CsPbI3 perovskite film with improved crystallinity and lower defect density is obtained. Most importantly, carbon-based PSCs (C-PSCs) based on the CsPbI3 perovskite film achieve an efficiency of 16.05%, a new record for inorganic C-PSCs.

Self-Driving Laboratories for Chemistry and Materials Science

Self-driving laboratories (SDLs) promise an accelerated application of the scientific method. Through the automation of experimental workflows, along with autonomous experimental planning, SDLs hold the potential to greatly accelerate research in chemistry and materials discovery. This review provides an in-depth analysis of the state-of-the-art in SDL technology, its applications across various scientific disciplines, and the potential implications for research and industry. This review additionally provides an overview of the enabling technologies for SDLs, including their hardware, software, and integration with laboratory infrastructure. Most importantly, this review explores the diverse range of scientific domains where SDLs have made significant contributions, from drug discovery and materials science to genomics and chemistry. We provide a comprehensive review of existing real-world examples of SDLs, their different levels of automation, and the challenges and limitations associated with each domain.

Pattern-Matched Polymer Ligands Toward Near-Perfect Synergistic Passivation for High-Performance and Stable Br/Cl Mixed Perovskite Light-Emitting Diodes

Mixed Br/Cl perovskite nanocrystals (PeNCs) exhibit bright pure-blue emission benefiting for fulfilling the Rec. 2100 standard. However, phase segregation remains a significant challenge that severely affects the stability and emission spectrum of perovskite light-emitting diodes (PeLEDs). Here, we demonstrate the optimization of the spacing between polydentate functional groups of polymer ligands to match the surface pattern of CsPbBr1.8Cl1.2 PeNCs, resulting in effective synergistic passivation effect and significant improvements in PeLED performances. The block and alternating copolymers with different inter-functional group spacing are facilely synthesized as ligands for PeNCs. Surprisingly, block copolymers with a higher functional group density do not match PeNCs, while alternating copolymers enable efficient PeNCs with the high photoluminescence intensity, low non-radiative recombination rate and high exciton binding energy. Density functional theory calculations clearly confirm the almost perfect match between alternating copolymers and PeNCs. Finally, pure-blue PeLEDs are achieved with the emission at 467 nm and Commission Internationale de l'Eclairage (CIE) coordinates of (0.131, 0.071), high external quantum efficiency (9.1 %) and record spectral and operational stabilities (~80 mins) in mixed-halide PeLEDs. Overall, this study contributes to designing the polymer ligands and promoting the development of high-performance and stable pure-color PeLEDs towards display applications.

Single Crystal Ruddlesden-Popper and Dion-Jacobson Metal Halide Perovskites for Visible Light Photodetectors: Present Status and Future Perspectives

2D metal halide perovskites (MHPs), mainly the studied Ruddlesden-Popper (RP) and Dion-Jacobson (DJ) phases, have gained enormous popularity as optoelectronic materials owing to their self-assembled multiple quantum well structures, tunable semiconducting properties, and improved structural stability compared to their bulk 3D counterparts. The performance of polycrystalline thin film devices is limited due to the formation of defects and trap states. However, as studied so far, single crystal-based devices can provide a better platform to improve device performance and investigate their fundamental properties more reliably. This Review provides the first comprehensive report on the emerging field of RP and DJ perovskite single crystals and their use in visible light photodetectors of varied device configurations. This Review structurally summarizes the 2D MHP single crystal growth methods and the parameters that control the crystal growth process. In addition, the characterization techniques used to investigate their crystal properties are discussed. The review further provides detailed insights into the working mechanisms as well as the operational performance of 2D MHP single crystal photodetector devices. In the end, to outline the present status and future directions, this Review provides a forward-looking perspective concerning the technical challenges and bottlenecks associated with the developing field of RP and DJ perovskite single crystals. Therefore, this timely review will provide a detailed overview of the fast-growing field of 2D MHP single crystal-based photodetectors as well as ignite new concepts for a wide range of applications including solar cells, photocatalysts, solar H2 production, neuromorphic bioelectronics, memory devices, etc.

Rapid Recovery of Degraded Perovskite Single-Crystal Radiation Detectors via Infrared Healing

Radiation detectors based on metal halide perovskite (MHP) single crystals (SCs) have exhibited exceptional sensitivity, low detection limit, and remarkable energy resolution. However, the operational stability issue still dramatically impedes their commercialization due to degradation induced by high-energy irradiation and large bias. Here, we propose an innovative infrared healing strategy to restore the devices that have undergone severe damage from both long-term biasing and X-ray irradiation. Compared to the slow and inefficient intrinsic self-healing process of MHPs, the infrared healing method demonstrates the capacity to achieve rapid recovery of the detection performance of the degraded devices within just 1 h. We reveal that the healing mechanism is mainly related to the reduction of the ion-migration activation energy in MHP SCs under infrared illumination, which promotes the back diffusion of the displaced ions to their original lattice positions and remedies defects. Finally, the healing effect is further confirmed through the gamma-ray spectroscopy acquisition with degraded MHP SCs, whose energy resolution at 59.5 keV of 241Am source is improved from 36% to 12% following infrared illumination. These results present infrared healing as a simple and economic method to extend the service life of MHP SC-based detectors.

What Matters for the Charge Transport of 2D Perovskites?

Compared to 3D perovskites, 2D perovskites exhibit excellent stability, structural diversity, and tunable bandgaps, making them highly promising for applications in solar cells, light-emitting diodes, and photodetectors. However, the trade-off for worse charge transport is a critical issue that needs to be addressed. This comprehensive review first discusses the structure of 3D and 2D metal halide perovskites, then summarizes the significant factors influencing charge transport in detail and provides a brief overview of the testing methods. Subsequently, various strategies to improve the charge transport are presented, including tuning A'-site organic spacer cations, A-site cations, B-site metal cations, and X-site halide ions. Finally, an outlook on the future development of improving the 2D perovskites' charge transport is discussed.

Printed On-Chip Perovskite Heterostructure Arrays for Optical Switchable Logic Gates

The use of optoelectronic devices for high-speed and low-power data transmission and computing is considered in the next-generation logic circuits. Heterostructures, which can generate and transmit photoresponse signals dealing with different input lights, are highly desirable for optoelectronic logic gates. Here, the printed on-chip perovskite heterostructures are demonstrated to achieve optical-controlled "AND" and "OR" optoelectronic logic gates. Perovskite heterostructures are printed with a high degree of control over composition, site, and crystallization. Different regions of the printed perovskite heterostructures exhibit distinguishable photoresponse to varied wavelengths of input lights, which can be utilized to achieve optical-controlled logic functions. Correspondingly, parallel operations of the two logic gates ("AND" and "OR") by way of choosing the output electrodes under the single perovskite heterostructure. Benefiting from the uniform crystallization and strict alignment of the printed perovskite heterostructures, the integrated 3 × 3 pixels all exhibit 100% logic operation accuracy. Finally, optical-controlled logic gates responding to multiwavelength light can be printed on the predesigned microelectrodes as the on-chip integrated circuits. This printing strategy allows for integrating heterostructure-based optical and electronic devices from a unit-scale device to a system-scale device.

Achieving Low-Dose Rate X-Ray Imaging Based on 2D/3D-Mixed Perovskite Films

X-ray detection and imaging are widely used in medical diagnosis, product inspection, security monitoring, etc. Large-scale polycrystalline perovskite thick films possess high potential for direct X-ray imaging. However, the notorious problems of baseline drift and high detection limit caused by ions migration are still remained. Here, ion migration is reduced by incorporating 2D perovskite into 3D perovskite, thereby increasing the ion activation energy. This approach hinders ion migration within the perovskite film, consequently suppressing baseline drift and reducing the lowest detection limit(LOD) of the device. As a result, the baseline drifting declines by 20 times and the LOD reduces to 21.1 nGy s-1, while the device maintains a satisfactory sensitivity of 5.6 × 103 µC Gy-1 cm-2. This work provides a new strategy to achieve low ion migration in large-scale X-ray detectors and may provide new thoughts for the application of mixed-dimension perovskite.

Large dynamic scissoring mode displacements coupled to band gap opening in the cubic phase of the methylammonium lead halide perovskites

Hybrid perovskites are a rapidly growing research area, having reached photovoltaic power conversion efficiencies of over 25%. There is a increasing consensus that the structures of these materials, and hence their electronic structures, cannot be understood purely from the time and space averaged crystal structures observable by conventional methods. We apply a symmetry-motivated analysis method to analyse x-ray pair distribution function data of the cubic phases of the hybrid perovskites MAPbX3(X= I, Br, Cl). We demonstrate that, even in the cubic phase, the local structure of the inorganic components of MAPbX3(X= I, Br, Cl), are dominated by scissoring type deformations of the PbX6octahedra. We find these modes to have a larger amplitude than equivalent distortions in theA-site deficient perovskite ScF3and demonstrate that they show a significant departure from the harmonic approximation. Calculations performed on an inorganic perovskite analogue, FrPbBr3, show that the large amplitudes of the scissoring modes are coupled to a dynamic opening of the electronic band gap. Finally, we use density functional theory calculations to show that the organic MA cations reorientate to accommodate the large amplitude scissoring modes.

Recent Advances in Fast-Decaying Metal Halide Perovskites Scintillators

Fast-decaying scintillators show subnanoseconds or nanoseconds lifetime and high time resolution, making them important in nuclear physics, medical diagnostics, scientific research, and other fields. Metal halide perovskites (MHPs) show great potential for scintillator applications owing to their easy synthesis procedure and attractive optical properties. However, MHPs scintillators still need further improvement in decay lifetime. To optimize the decay lifetime, great progress has been achieved recently. In this Perspective, we first summarize the structural characteristics of MHPs in various dimensions, which brings different exciton behaviors. Then, recent advances in designing fast-decaying MHPs according to different exciton behaviors have been concluded, focusing on the photophysical mechanisms to achieve fast-decaying lifetimes. These advancements in decay lifetimes could facilitate the MHPs scintillators in advanced applications, such as time-of-flight positron emission tomography (TOF-PET), photon-counting computed tomography (PCCT), etc. Finally, the challenges and future opportunities are discussed to provide a roadmap for designing novel fast-decaying MHPs scintillators.

Direct detection of minimum ionizing charged particles in a perovskite single crystal detector with single particle sensitivity

We report the detection of high energy electrons of some hundreds of MeV, crossing a methylammonium lead bromide single crystal device with sensitivity down to a single electron. In the device, the released energy is close to the energy released by minimum-ionizing particles. This is the first demonstration of a perovskite-based device that can be used for tracking and counting minimum-ionizing charged particles. The device reaches single particle sensitivity with a low bias voltage of 5 V. It also shows a good linearity of the response as a function of the number of electrons in a dynamic range of approximately 104.

Understanding of Defect Passivation Effect on Wide Band Gap p-i-n Perovskite Solar Cell

The wide band gap perovskite solar cells (PSCs) have attracted considerable attention for their great potential as top cells in high efficiency tandem cell application. However, the photovoltaic performance and stability of PSCs are constrained by nonradiative recombination, primarily stemming from defects within the bulk and at the interface of charge transport layer/perovskite and phase segregation. In this study, we systematically investigated the effects of 2-thiopheneethylammonium chloride (TEACl) on a wide band gap (∼1.67 eV) Cs0.15FA0.65MA0.20Pb(I0.8Br0.2)3 (CsFAMA) perovskite solar cell. TEACl was employed as a passivation layer between the perovskite and electron transport layer (ETL). With TEACl treatment, charged defects responsible for sub-band absorption and electrostatic potential fluctuation were effectively suppressed by the passivation of bulk defects. The incorporation of TEACl, which led to the formation of a TEA2PbX4/Perovskite (2D/3D) heterojunction, facilitated better band alignment and effective passivation of interface defects at the ETL/CsFAMA. Owing to these beneficial effects, the TEACl passivated PSC achieved a photo conversion efficiency (PCE) of 19.70% and retained ∼85% of initial PCE over ∼1900 h, surpassing the performance of the untreated PSC, which exhibited a PCE of 16.69% and retained only ∼37% of its initial PCE.

Recent advances in two-dimensional perovskite materials for light-emitting diodes

Light-emitting diodes (LEDs) are an indispensable part of our daily life. After being studied for a few decades, this field still has some room for improvement. In this regard, perovskite materials may take the leading role. In recent years, LEDs have become a most explored topic, owing to their various applications in photodetectors, solar cells, lasers, and so on. Noticeably, they exhibit significant characteristics in developing LEDs. The luminous efficiency of LEDs can be significantly enhanced by the combination of a poor illumination LED with low-dimensional perovskite. In 2014, the first perovskite-based LED was illuminated at room temperature. Furthermore, two-dimensional (2D) perovskites have enriched this field because of their optical and electronic properties and comparatively high stability in ambient conditions. Recent and relevant advancements in LEDs using low-dimensional perovskites including zero-dimensional to three-dimensional materials is reported. The major focus of this article is based on the 2D perovskites and their heterostructures (i.e., a combination of 2D perovskites with transition metal dichalcogenides, graphene, and hexagonal boron nitride). In comparison to 2D perovskites, heterostructures exhibit more potential for application in LEDs. State-of-the-art perovskite-based LEDs, current challenges, and prospects are also discussed.

Tuning Thermal Conductivity of Hybrid Perovskites through Halide Alloying

Tuning the thermal transport properties of hybrid halide perovskites is critical for their applications in optoelectronics, thermoelectrics, and photovoltaics. Here, an effective strategy is demonstrated to modulate the thermal transport property of hybrid perovskites by halide alloying. A highly tunable thermal conductivity of mixed-halide hybrid perovskites is achieved due to halide-alloying and structural distortion. The experimental measurements show that the room temperature thermal conductivity of MAPb(BrxI1- x)3 (x = 0─1) can be largely modulated from 0.27 ± 0.07 W m-1 K-1 (x = 0.5) to 0.47 ± 0.09 W m-1 K-1 (x = 1). Molecular dynamics simulations further demonstrate that the thermal conductivity reduction of hybrid halide perovskites results from the suppression of the mean free paths of the low-frequency acoustic and optical phonons. It is found that halide alloying and the induced structural distortion can largely increase the scatterings of optical and acoustic phonons, respectively. The confined diffusion of MA+ cations in the octahedra cage is found to act as an additional thermal transport channel in hybrid perovskites and can contribute around 10-20% of the total thermal conductivity. The findings provide a strategy for tailoring the thermal transport in hybrid halide perovskites, which may largely benefit their related applications.

Dion-Jacobson Type Lead-Free Double Perovskite with Ultra-Narrow Aromatic Interlayer Spacing for Highly Sensitive and Stable X-ray Detection

The low-toxic and environmentally friendly 2D lead-free perovskite has made significant progress in the exploration of "green" X-ray detectors. However, the gap in detection performance between them and their lead-based analogues remains a matter of concern that cannot be ignored. To reduce this gap, shortening the interlayer spacing to accelerate the migration and collection of X-ray carriers is a promising strategy. Herein, a Dion-Jacobson (DJ) lead-free double perovskite (4-AP)2AgBiBr8 (1, 4-AP = 4-amidinopyridine) with an ultra-narrow interlayer spacing of 3.0 Å, is constructed by utilizing π-conjugated aromatic spacers. Strikingly, the subsequent enhanced carrier transport and increased crystal density lead to X-ray detectors based on bulk single crystals of 1 with a high sensitivity of 1117.3 µC Gy-1 cm-2, superior to the vast majority of similar double perovskites. In particular, the tight connection of the inorganic layers by the divalent cations enhances structural rigidity and stability, further endowing 1 detector with ultralow dark current drift (3.06 × 10-8 nA cm-1 s-1 V-1, 80 V), excellent multiple cycles switching X-ray irradiation stability, as well as long-term environmental stability (maintains over 94% photoresponse after 90 days). This work brings lead-free double perovskites one step closer to realizing efficient practical green applications.

Ethanol purification enables high-quality α-phase FAPbI3 perovskite microcrystals for commercial photovoltaic applications

Reliable quality and sustainable processes must be developed for commodities to enter the commercial stage. For next-generation photovoltaic applications such as perovskite solar cells, it is essential to manufacture high-quality photoactive perovskites via eco-friendly processes. We demonstrate that ethanol, an ideal green solvent, can be applied to yield efficient alpha-phase FAPbI3 perovskite microcrystals.

Enhancement of Photodetector Characteristics by Zn-Porphyrin-Passivated MAPbBr3 Single Crystals

Perovskite single crystals have garnered significant interest in photodetector applications due to their exceptional optoelectronic properties. The outstanding crystalline quality of these materials further enhances their potential for efficient charge transport, making them promising candidates for next-generation photodetector devices. This article reports the synthesis of methyl ammonium lead bromide (MAPbBr3) perovskite single crystal (SC) via the inverse-temperature crystallization method. To further improve the performance of the photodetector, Zn-porphyrin (Zn-PP) was used as a passivating agent during the growth of SC. The optical characterization confirmed the enhancement of optical properties with Zn-PP passivation. On single-crystal surfaces, integrated photodetectors are fabricated, and their photodetection performances are evaluated. The results show that the single-crystalline photodetector passivated with 0.05% Zn-PP enhanced photodetection properties and rapid response speed. The photoelectric performance of the device, including its responsivity (R), external quantum efficiency (EQE), detective nature (D), and noise-equivalent power (NEP), showed an enhancement of the un-passivated devices. This development introduces a new potential to employ high-quality perovskite single-crystal-based devices for more advanced optoelectronics.

Reproducible high-quality perovskite single crystals by flux-regulated crystallization with a feedback loop

Controlling the linear growth rate, a critical factor that determines crystal quality, has been a challenge in solution-grown single crystals due to complex crystallization kinetics influenced by multiple parameters. Here we introduce a flux-regulated crystallization (FRC) method to directly monitor and feedback-control the linear growth rate, circumventing the need to control individual growth conditions. When applied to metal halide perovskites, the FRC maintains a stable linear growth rate for over 40 h in synthesizing CH3NH3PbBr3 and CsPbBr3 single crystals, achieving outstanding crystallinity (quantified by a full width at half-maximum of 15.3 arcsec in the X-ray rocking curve) in a centimetre-scale single crystal. The FRC is a reliable platform for synthesizing high-quality crystals essential for commercialization and systematically exploring crystallization conditions, maintaining a key parameter-the linear growth rate-constant, which enables a comprehensive understanding of the impact of other influencing factors.

Perovskite Single Crystals by Vacuum Evaporation Crystallization

Perovskite single crystals have attracted tremendous attention owing to their excellent optoelectronic properties and stability compared to typical multicrystal structures. However, the growth of high-quality perovskite single crystals (PSCs) generally relies on temperature gradients or the introduction of additives to promote crystal growth. In this study, a vacuum evaporation crystallization technique is developed that allows PSCs to be grown under extremely stable conditions at constant temperature and without requiring additives to promote crystal growth. The new method enables the growth of PSCs of unprecedented quality, that is, MAPbBr3 single crystals that exhibit an ultranarrow full width at half maximum of 0.00701°, which surpasses that of all previously reported values. In addition, the MAPbBr3 single crystals deliver exceptional optoelectronic performance, including a long carrier lifetime of 1006 ns, an ultralow trap-state density of 3.67 × 109 cm-3, and an ultrahigh carrier mobility of 185.86 cm2 V-1 s-1. This method is applicable to various types of PSCs, including organic-inorganic hybrids, fully inorganic structures, and low-dimensional structures.