Piezophototronic gated optofluidic logic computations empowering intrinsic reconfigurable switches

A reprogrammable mechanical metamaterial with origami functional-group transformation and ring reconfiguration

Recent advancements in reprogrammable metamaterials have enabled the development of intelligent matters with variable special properties in situ. These metamaterials employ intra-element physical reconfiguration and inter-element structural transformation. However, existing mono-characteristic homo-element mechanical metamaterials have limited reprogramming functions. Here, we introduce a reprogrammable mechanical metamaterial composed of origami elements with heterogeneous mechanical properties, which achieves various mechanical behavior patterns by functional group transformations and ring reconfigurations. Through the anisotropic assembly of two heterogeneous elements into a functional group, we enable mechanical behavior switching between positive and negative stiffness. The resulting polygonal ring exhibits rotational deformation, zero Poisson's ratio stretching/compression deformation, and negative Poisson's ratio auxetic deformation. Arranging these rings periodically yields homogeneous metamaterials. The reconfiguration of quadrilateral rings allows for continuous fine-tunability of the mechanical response and negative Poisson's ratio. This mechanical metamaterial could provide a versatile material platform for reprogrammable mechanical computing, multi-purpose robots, transformable vehicles and architectures at different scales.

Dual-modal piezotronic transistor for highly sensitive vertical force sensing and lateral strain sensing

Mechanical sensors are mainly divided into two types (vertical force sensing and lateral strain sensing). Up to now, one sensor with two working modes is still a challenge. Here, we demonstrate a structural design concept combing a piezoelectric nano/microwire with a flexible polymer with protrusions that enables a dual-modal piezotronic transistor (DPT) with two working modes for highly sensitive vertical force sensing and lateral strain sensing. For vertical force sensing, DPT exhibits a force sensitivity up to 221.5 N-1 and a minimum identifiable force down to 21 mN, corresponding to a pressure sensitivity of 1.759 eV/MPa. For lateral strain sensing, DPT can respond to a large compression strain (~5.8%) with an on/off ratio up to 386.57 and a gauge factor up to 8988.6. It is a universal design that can integrate vertical force sensing and lateral strain sensing into only one nanodevice, providing a feasible strategy for multimodal devices.

Sensing High 17β-Estradiol Concentrations Using a Planar Microwave Sensor Integrated with a Microfluidic Channel

The global issue of pollution caused by endocrine-disrupting chemicals (EDCs) has been gaining increasing attention. Among the EDCs of environmental concern, 17β-estradiol (E2) can produce the strongest estrogenic effects when it enters the organism exogenously through various routes and has the potential to cause harm, including malfunctions of the endocrine system and development of growth and reproductive disorders in humans and animals. Additionally, in humans, supraphysiological levels of E2 have been associated with a range of E2-dependent disorders and cancers. To ensure environmental safety and prevent potential risks of E2 to human and animal health, it is crucial to develop rapid, sensitive, low cost and simple approaches for detecting E2 contamination in the environment. A planar microwave sensor for E2 sensing is presented based on the integration of a microstrip transmission line (TL) loaded with a Peano fractal geometry with a narrow slot complementary split-ring resonator (PF-NSCSRR) and a microfluidic channel. The proposed technique offers a wide linear range for detecting E2, ranging from 0.001 to 10 mM, and can achieve high sensitivity with small sample volumes and simple operation methods. The proposed microwave sensor was validated through simulations and empirical measurements within a frequency range of 0.5-3.5 GHz. The E2 solution was delivered to the sensitive area of the sensor device via a microfluidic polydimethylsiloxane (PDMS) channel with an area of 2.7 mm² and sample value of 1.37 µL and measured by a proposed sensor. The injection of E2 into the channel resulted in changes in the transmission coefficient (S₂₁) and resonance frequency (F_r), which can be used as an indicator of E₂ levels in solution. The maximum quality factor of 114.89 and the maximum sensitivity based on S₂₁ and F_r at a concentration of 0.01 mM were 1746.98 dB/mM and 40 GHz/mM, respectively. Upon comparing the proposed sensor with the original Peano fractal geometry with complementary split-ring (PF-CSRR) sensors without a narrow slot, several parameters were evaluated, including sensitivity, quality factor, operating frequency, active area, and sample volume. The results showed that the proposed sensor exhibited an increased sensitivity of 6.08% and had a 40.72% higher quality factor, while the operating frequency, active area, and sample volume showed decreases of 1.71%, 25%, and 28.27%, respectively. The materials under tests (MUTs) were analyzed and categorized into groups using principal component analysis (PCA) with a K-mean clustering algorithm. The proposed E2 sensor has a compact size and simple structure that can be easily fabricated with low-cost materials. With the small sample volume requirement, fast measurement with a wide dynamic range, and a simple protocol, this proposed sensor can also be applied to measure high E2 levels in environmental, human, and animal samples.

A high performance lead-free flexible piezoelectric nanogenerator based on AlFeO3nanorods interspersed in PDMS matrix for biomechanical energy scavenging to sustainably power electronics

Since lead-based piezoelectric nanogenerators (PENGs) possess serious health risks, environmental problems, proper disposal issues, and biocompatibility concerns, this work presents the fabrication of a flexible piezoelectric nanogenerator utilizing lead-free orthorhombic AlFeO₃nanorods for biomechanical energy scavenging to sustainably power electronics. Hydrothermal technique is used to synthesize the AlFeO₃nanorods and the PENG was fabricated on Indium tin oxide (ITO) coated Polyethylene terephthalate (PET) flexible film with AlFeO₃nanorods interspersed in polydimethylsiloxane (PDMS). transmission electron microscopy proved that the AlFeO₃nanoparticles are of nanorods shape. Through x-ray Diffraction, it is validated that AlFeO₃nanorods have orthorhombic phase and crystalline structure. A high piezoelectric charge coefficient (d₃₃) of 400 pm V^-1is obtained from the piezoelectric force microscopy of AlFeO₃nanorods. With optimized concentration of AlFeO₃in the polymer matrix, an open circuit voltage (V_OC) of 30.5 V, current density (J_C) of 0.7888±0.0001μA cm^-2and an instantaneous power density of 240.6 mW m^-2are obtained under the application of a force of 1.25 kgf. To investigate the nanogenerator's practical utility, the PENG is used for lighting multiple LEDs, charging of a capacitor and as a pedometer via biomechanical energy harvesting. Hence, it can be employed for developing various self-powered wearable electronics such as flexible skin, artificial cutaneous sensors, etc.

Proton conducting metal-organic frameworks with light response for multistate logic gates

The simulation of neurons receiving stimulation and transmitting signals by proton conduction has great potential applications in electrochemistry and biology. In this work, copper tetrakis(4-carboxyphenyl)porphyrin (Cu-TCPP), which is a proton conductive metal organic framework (MOF) with photothermal response, is adopted as the structural framework, with the in situ co-incorporation of polystyrene sulfonate (PSS) and sulfonated spiropyran (SSP) to prepare the composite membranes. The resultant PSS-SSP@Cu-TCPP thin-film membranes were used as the logic gates i.e., NO gate, NOR gate and NAND gate because of the photothermal effect of Cu-TCPP MOFs and the photoinduced conformational changes of SSP. This membrane exhibits the high proton conductivity of 1.37 × 10^-4 S cm^-1. Under the conditions of 55 °C and 95% relative humidity (RH), using 405 nm laser irradiation with 400 mW cm^-2 and 520 nm laser irradiation with 200 mW cm^-2 as inputs, the device can be adjusted between various steady states, and the value of the conductivity is regarded as the output with different thresholds in different logic gates. Before and after laser irradiation, the electrical conductivity changes dramatically, and the ON/OFF switching ratio reached 1068. The application of three logic gates is realized by constructing circuits with LED lights. Depending on the convenience of light and the easy measurement of conductivity, this kind of device with light source as input and electrical signal as output provides the possibility to realize the remote control of chemical sensors and complex logic gates devices.

In Situ Quantification of Strain-Induced Piezoelectric Potential of Dynamically Bending ZnO Microwires

The piezoelectric properties of semiconductor micro/nanowires (M/NWs) are crucial for optimizing semiconductors' electronic structure and carrier dynamics. However, the dynamic characterization of the piezoelectric properties of M/NWs remains challenging. Here, a Kelvin probe force microscopy technique based on a dual-probe atomic force microscope is developed to achieve in situ piezoelectric potential measurements of dynamic bending MWs. This technique can not only characterize the surface potential on different crystal faces of ZnO MWs in a natural state through controllable axial rotation, but also investigate the piezoelectric potential of the dynamically bending flake-like ZnO MW at different points and under different strain loads. The results show that the surface potentials of different faces/positions of the ZnO MWs are varied significantly, and determine that the quasi-static conditions piezo-strain factor of the flake-like ZnO MW is 0.28 V/%, while the factor was 0.14 V/% under low-frequency (⩽5 Hz) sinusoidal strain loading. This work provides a significant methodology to further study piezoelectric materials, and it aims to facilitate their applications in piezoelectric devices and systems.

Optimized Design of a Self-Biased Amplifier for Seizure Detection Supplied by Piezoelectric Nanogenerator: Metaheuristic Algorithms versus ANN-Assisted Goal Attainment Method

This work is dedicated to parameter optimization for a self-biased amplifier to be used in preamplifiers for the diagnosis of seizures in neuro-diseases such as epilepsy. For the sake of maximum compactness, which is obligatory for all implantable devices, power is to be supplied by a piezoelectric nanogenerator (PENG). Several meta-heuristic optimization algorithms and an ANN (artificial neural network)-assisted goal attainment method were applied to the circuit, aiming to provide us with the set of optimal design parameters which ensure the minimal overall area of the preamplifier. These parameters are the slew rate, load capacitor, gain–bandwidth product, maximal input voltage, minimal input voltage, input voltage, reference voltage, and dissipation power. The results are re-evaluated and compared in the Cadence 180 nm SCL environment. It has been observed that, among the metaheuristic algorithms, the whale optimization technique reached the best values at low computational cost, decreased complexity, and the highest convergence speed. However, all metaheuristic algorithms were outperformed by the ANN-assisted goal attainment method, which produced a roughly 50% smaller overall area of the preamplifier. All the techniques described here are applicable to the design and optimization of wearable or implantable circuits.

Highly sensitive strain sensors based on piezotronic tunneling junction

Piezotronics with capacity of constructing adaptive and seamless interactions between electronics/machines and human/ambient are of value in Internet of Things, artificial intelligence and biomedical engineering. Here, we report a kind of highly sensitive strain sensor based on piezotronic tunneling junction (Ag/HfO₂/n-ZnO), which utilizes the strain-induced piezoelectric potential to control the tunneling barrier height and width in parallel, and hence to synergistically modulate the electrical transport process. The piezotronic tunneling strain sensor has a high on/off ratio of 478.4 and high gauge factor of 4.8 × 10⁵ at the strain of 0.10%, which is more than 17.8 times larger than that of a conventional Schottky-barrier based strain sensor in control group as well as some existing ZnO nanowire or nanobelt based sensors. This work provides in-depth understanding for the basic mechanism of piezotronic modulation on tunneling junction, and realizes the highly sensitive strain sensor of piezotronic tunneling junction on device scale, which has great potential in advanced micro/nano-electromechanical devices and systems.

Strain-induced piezoelectric polarization can be used to modulate the interface electrical transport. Here, the authors achieved a piezotronic tunneling strain sensor at device scale with optimized performance based on the structure of Ag/HfO2/n-ZnO.

Wearable Triboelectric Nanogenerator from Waste Materials for Autonomous Information Transmission via Morse Code

Electronic waste produced by plastic, toxic, and semiconducting components of existing electronic devices is dramatically increasing environmental pollution. To overcome these issues, the use of eco-friendly materials for designing such devices is attaining much attention. This current work presents a recycled material-based triboelectric nanogenerator (TENG) made of plastic waste and carbon-coated paper wipes (C@PWs), in which the PWs are also collected from a waste bin. The resultant C@PW-based TENG is then used for powering low-power electronic devices and, later, to generate a Morse code from a wearable for autonomous communication. In this application, the end users decode the Morse code from a customized LabVIEW program and read the transmitted signal. With further redesigning, a 9-segment keyboard is developed using nine-TENGs, connected to an Arduino controller to display the 9-segment actuation on a computer screen. Based on the above analysis, our C@PW-TENG device is expected to have an impact on future self-powered sensors and internet of things systems.

Progress in Piezoelectric Nanogenerators Based on PVDF Composite Films

In recent years, great progress has been made in the field of energy harvesting to satisfy increasing needs for portable, sustainable, and renewable energy. Among piezoelectric materials, poly(vinylidene fluoride) (PVDF) and its copolymers are the most promising materials for piezoelectric nanogenerators (PENGs) due to their unique electroactivity, high flexibility, good machinability, and long–term stability. So far, PVDF–based PENGs have made remarkable progress. In this paper, the effects of the existence of various nanofillers, including organic–inorganic lead halide perovskites, inorganic lead halide perovskites, perovskite–type oxides, semiconductor piezoelectric materials, two–dimensional layered materials, and ions, in PVDF and its copolymer structure on their piezoelectric response and energy–harvesting properties are reviewed. This review will enable researchers to understand the piezoelectric mechanisms of the PVDF–based composite–film PENGs, so as to effectively convert environmental mechanical stimulus into electrical energy, and finally realize self–powered sensors or high–performance power sources for electronic devices.

Tunable multi-wavelength optofluidic Dammann grating with beam splitting property

Dammann grating (DG) is a binary beam splitter. Traditional DG is pure solid and cannot be modulated for different working wavelength. We report a tunable multi-wavelength DG based on a liquid-solid hybrid structure. Two glass plates are bonded by UV adhesive strips, one has a periodic grooves structure made by photoresist, the other has two drilled holes as inlet and outlet, respectively. A microfluidic mixer connected the inlet mixes of two miscible liquids with different flow rates to adjust the refractive index of the mixed liquid entering DG from 1.351 to 1.473. In the experiment, the real-time tunability has shown the DG achieves well beam splitting effect when parameter N is integer, 7 × 7 light spots are arranged in order with good uniformity. For λ = 632.8 nm, spot size uniformity is about 78.38% and power uniformity is ∼71.01%. For λ = 532 nm, the spot size and power uniformity are about 77.17% and 64.32%, respectively. The experiment also demonstrates this DG's suitability for near-infrared light. This work is the first study of tunable DG based on liquid-solid hybrid structure and possesses special merits as compared to its solid counterpart, such as simple fabrication, tunability and multi-wavelength applicability, which make it have an extensive prospect in optofluidic networks and optical devices.

A Stretchable, Self-Healable Triboelectric Nanogenerator as Electronic Skin for Energy Harvesting and Tactile Sensing

Electronic skin that is deformable, self-healable, and self-powered has high competitiveness for next-generation energy/sense/robotic applications. Herein, we fabricated a stretchable, self-healable triboelectric nanogenerator (SH-TENG) as electronic skin for energy harvesting and tactile sensing. The elongation of SH-TENG can achieve 800% (uniaxial strain) and the SH-TENG can self-heal within 2.5 min. The SH-TENG is based on the single-electrode mode, which is constructed from ion hydrogels with an area of 2 cm × 3 cm, the output of short-circuit transferred charge (Qsc), open-circuit voltage (Voc), and short-circuit current (Isc) reaches ~6 nC, ~22 V, and ~400 nA, and the corresponding output power density is ~2.9 μW × cm⁻² when the matching resistance was ~140 MΩ. As a biomechanical energy harvesting device, the SH-TENG also can drive red light-emitting diodes (LEDs) bulbs. Meanwhile, SH-TENG has shown good sensitivity to low-frequency human touch and can be used as an artificial electronic skin for touch/pressure sensing. This work provides a suitable candidate for the material selection of the hydrogel-based self-powered electronic skin.

All-fiber phase modulator and switch based on local surface plasmon resonance effect of the gold nanoparticles embedded in gel membrane

All-fiber modulators and switches have drawn great interest in the photonics domain, and they are applied in viable photonic and optoelectronic devices. In this work, with the assistance of an agarose membrane, aspherical gold nanoparticles are embedded on the surface of the microfiber treated with the piranha solution. An all-fiber Mach-Zehnder interferometer was used to realize a low-cost, low-loss, and conveniently prepared all-fiber phase modulator. By taking advantage of the local surface plasmon resonance effect of gold nanoparticles embedded in the agarose membrane, under the excitation of near-infrared region light, the gold nanoparticles were excited to change the effective refractive index of one arm of the Mach-Zehnder interferometer. A maximum phase shift of ∼6π at 1550 nm was obtained from the device. In addition, an all-optical switch was achieved with a rising edge time of 47 ms and falling edge time of 14 ms. The proposed all-fiber modulator and switch based on the local surface plasmon resonance effect of gold nanoparticles embedded in agarose membrane will provide great potential in all-optical fiber systems.

In situ-grown organo-lead bromide perovskite-induced electroactive γ-phase in aerogel PVDF films: an efficient photoactive material for piezoelectric energy harvesting and photodetector applications

The unique combination of piezoelectric energy harvesters and light detectors progressively strengthens their application in the development of modern electronics. Here, for the first time, we fabricated a polyvinylidene fluoride (PVDF) and formamidinium lead bromide nanoparticle (FAPbBr3 NP)-based composite aerogel film (FAPbBr3/PVDF) for harvesting electrical energy and photodetector applications. The uniform distribution of FAPbBr3 NPs in FAPbBr3/PVDF was achieved via the in situ synthesis of FAPbBr3 NPs in the PVDF matrix, which led to the stabilization of the γ-phase. The freeze-drying process induced an interconnected porous architecture in the composite film, making it more sensitive to small mechanical stimuli. Owing to this unique fabrication technique, the constructed aerogel film-based nanogenerator (FPNG) exhibited an output voltage and current of ∼26.2 V and ∼2.1 μA, respectively, which were 5-fold higher than that of the nanogenerator with the pure PVDF film. Also, the sensitivity of FPNG upon the irradiation of light was demonstrated by the output voltage reduction of ∼38%, indicating its capability as a light sensing device. Furthermore, the prepared FAPbBr3/PVDF composite was found to be an efficient candidate for light detection applications. A simple planar photodetector was fabricated with the 8.0 wt% FAPbBr3 NP-loaded PVDF composite, which displayed very high responsivity (8 A/W) and response speed of 2.6 s. Thus, this exclusive combination of synthesis and fabrication for the preparation of electro-active films opens a new horizon in the piezoelectric community for effective energy harvesting and light detector applications.