Self-cycled photo-Fenton-like system based on an artificial leaf with a solar-to-H2O2 conversion efficiency of 1.46

Simultaneous removal of tetracycline hydrochloride and hexavalent chromium by heterogeneous Fenton in a photocatalytic fuel cell system

In this work, a novel double-chamber system (PFC-Fenton), combined photocatalytic fuel cell (PFC) with Fenton, was constructed for tetracycline hydrochloride (TCH) and hexavalent chromium (Cr(VI)) removal and electricity production. Therein, Zn5(OH)6(CO3)2/Fe2O3/BiVO4/fluorine-doped SnO2 (ZIO/BiVO4/FTO) and carboxylated carbon nanotubes/polypyrrole/graphite felt (CCNTs/Ppy/GF) were served as photoanode and cathode, respectively. Under light irradiation, the removal efficiencies of TCH and Cr(VI) with the addition of H2O2 (2 mL) could reach 93.1% and 80.4%, respectively. Moreover, the first-order kinetic constants (7.37 × 10-3 min-1 of TCH and 3.94 × 10-3 min-1 of Cr(VI)) were 5.26 and 5.57 times as much as the absence of H2O2. Simultaneously, the maximum power density could be obtained 0.022 mW/cm2 at a current density of 0.353 mA/cm2. Therein, the main contribution of TCH degradation was ·OH and holes in anode chamber. The synergistic effect of photoelectrons, generated ·O2-, and H2O2 played a crucial role in the reduction of Cr(VI) in cathode chamber. The high-performance liquid chromatography-mass spectrometry indicated that TCH could be partially mineralized into CO2 and H2O. X-ray photoelectron spectroscope and X-ray absorption near-edge structure spectra showed that Cr(VI) could be reduced to Cr(III). After 5 times of cycling, the removal efficiencies of TCH and Cr(VI) were still greater than 70%, indicating the remarkable stability of the PFC-Fenton system. Overall, this system could remove TCH/Cr(VI) and generate power simultaneously without iron sludge formation, demonstrating a promising method to further develop PFC-Fenton technology.

Establishing an affordable solar-floating Fe2O3@A1-xRx-TiO2 photo-Fenton catalytic system through the cyclic utilization of iron waste to de-pollute textile water contamination

This study focuses on developing a cost-effective Fe2O3 catalyst from oilfield iron waste to create a floating heterogeneous photo-Fenton system with anatase/rutile(A/R) TiO2 heterophase photocatalyst (cork-Fe2O3@A1-xRx-TiO2) for treating textile pollution in sunlight. Through controlling sol-gel (SG) microwave heating technique, the A/R ratio of A1-xRx-TiO2 crystal is tuned (A/R ratio = 1.13 and Eg = 3.02 eV) to improve adsorption-photocatalytic removal of anionic/cationic dyes with an apparent kinetic rate (kapp) of 0.0074 min-1 under UV-visible irradiation. The developed cork-Fe2O3@A53.1R46.8-TiO2 floated system also outperforms the classical photo-Fenton with Fe/H2O2 benchmark, showing a 2-fold enhancement in textile dye degradation (kapp = 0.216 min-1 and space-time yield (SY) of 1.7*10-4 mol/E.g at pH 5.65) with high stability over four reuse cycles. The formation of Fe2O3@A53.1R46.8-TiO2 Type-II heterojunction is confirmed by optical and electrochemical analyses, allowing the acceleration of direct electron transfer mechanism and oxidative degradation of dyes during photo-Fenton reaction. As a case study, the cork-Fe2O3@A53.1R46.8-TiO2 system demonstrates a high capability for efficient mineralization of textile pollution in a real effluent, achieving 82 ± 2% reduction in the total organic contents at an operational cost of 2.61 $/kg.m3 in sunlight. Thus, this research addresses challenges in conventional Fenton chemistry, iron waste recycling, and catalyst retention, offering new insights for sustainable treatment of textile effluents and environmental protection.

In situ single iron atom doping on Bi2WO6 monolayers triggers efficient photo-fenton reaction

Developing an efficient photocatalytic system for hydrogen peroxide (H2O2) activation in Fenton-like processes holds significant promise for advancing water purification technologies. However, challenges such as high carrier recombination rates, limited active sites, and suboptimal H2O2 activation efficiency impede optimal performance. Here we show that single-iron-atom dispersed Bi2WO6 monolayers (SIAD-BWOM), designed through a facile hydrothermal approach, can offer abundant active sites for H2O2 activation. The SIAD-BWOM catalyst demonstrates superior photo-Fenton degradation capabilities, particularly for the persistent pesticide dinotefuran (DNF), showcasing its potential in addressing recalcitrant organic pollutants. We reveal that the incorporation of iron atoms in place of tungsten within the electron-rich [WO4]2- layers significantly facilitates electron transfer processes and boosts the Fe(II)/Fe(III) cycle efficiency. Complementary experimental investigations and theoretical analyses further elucidate how the atomically dispersed iron induces lattice strain in the Bi2WO6 monolayer, thereby modulating the d-band center of iron to improve H2O2 adsorption and activation. Our research provides a practical framework for developing advanced photo-Fenton catalysts, which can be used to treat emerging and refractory organic pollutants more effectively.

Oxygen-Centered Organic Radicals-Involved Unified Heterogeneous Self-Fenton Process for Stable Mineralization of Micropollutants in Water

Removing organic micropollutants from water through photocatalysis is hindered by catalyst instability and substantial residuals from incomplete mineralization. Here, a novel water treatment paradigm, the unified heterogeneous self-Fenton process (UHSFP), which achieved an impressive 32% photon utilization efficiency at 470 nm, and a significant 94% mineralization of organic micropollutants-all without the continual addition of oxidants and iron ions is presented. In UHSFP, the active species differs fundamentally from traditional photocatalytic processes. One electron acceptor unit of photocatalyst acquires only one photogenerated electron to convert into oxygen-centered organic radical (OCOR), then spontaneously completing subsequent processes, including pollutant degradation, hydrogen peroxide generation, activation, and mineralization of organic micropollutants. By bolstering electron-transfer capabilities and diminishing catalyst affinity for oxygen in the photocatalytic process, the generation of superoxide radicals is effectively suppressed, preventing detrimental attacks on the catalyst. This study introduces an innovative and cost-effective strategy for the efficient and stable mineralization of organic micropollutants, eliminating the necessity for continuous chemical inputs, providing a new perspective on water treatment technologies.

A H₂S-Evolving Alternately-Catalytic Enzyme Bio-Heterojunction with Antibacterial and Macrophage-Reprogramming Activity for All-Stage Infectious Wound Regeneration

The disorder of the macrophage phenotype and the hostile by-product of lactate evoked by pathogenic infection in hypoxic deep wound inevitably lead to the stagnant skin regeneration. In this study, hydrogen sulfide (H2S)-evolving alternately catalytic bio-heterojunction enzyme (AC-BioHJzyme) consisting of CuFe2S3 and lactate oxidase (LOD) named as CuFe2S3@LOD is developed. AC-BioHJzyme exhibits circular enzyme-mimetic antibacterial (EMA) activity and macrophage re-rousing capability, which can be activated by near-infrared-II (NIR-II) light. In this system, LOD exhausts lactate derived from bacterial anaerobic respiration and generated hydrogen peroxide (H2O2), which provides an abundant stock for the peroxidase-mimetic activity to convert the produced H2O2 into germicidal •OH. The GPx-mimetic activity endows AC-BioHJzyme with a glutathione consumption property to block the antioxidant systems in bacterial metabolism, while the O2 provided by the CAT-mimetic activity can generate 1O2 under the NIR-II irradiation. Synchronously, the H2S gas liberated from CuFe2S3@LOD under the infectious micromilieu allows the reduction of Fe(III)/Cu(II) to Fe(II)/Cu(І), resulting in sustained circular EMA activity. In vitro and in vivo assays indicate that the CuFe2S3@LOD AC-BioHJzyme significantly facilitates the infectious cutaneous regeneration by killing bacteria, facilitating epithelialization/collagen deposition, promoting angiogenesis, and reprogramming macrophages. This study provides a countermeasure for deep infectious wound healing via circular enzyme-mimetic antibiosis and macrophage re-rousing.

MoS2-mediated active hydrogen modulation to boost Fe2+ regeneration in solar-driven electro-Fenton process

The sluggish kinetics of Fe2+ regeneration seriously hinders the performance of Fenton process. However, the conventional Fenton system excessively stifle hydrogen-producing reactions, ignoring the significance of active hydrogen (H*) in Fe3+ reduction. Herein, a strategy of H* modulation is developed by decorating molybdenum disulfide (MoS2) on a graphite felt (GF) cathode to boost Fe2+ regeneration in solar-driven electro-Fenton (SEF) process. With MoS2 regulation, moderately dispersed MoS2 on GF can serve as a bifunctional cathode, where the H* and hydrogen peroxide (H2O2) are simultaneously generated through H+ reduction and O2 reduction, respectively. The in-situ generated H2O2 can trigger Fenton reactions with Fe2+, while the H* with robust reducing potential can significantly expedite Fe3+ reduction, consequently enhancing the HO• production. Both DFT calculations and EPR experiments confirm that H* can be activated via MoS2 decoration. The results show that Fe2+ concentration in the MoS2 @GF-SEF system remains at 15.74 mg/L (56.21%) after 6 h, which is 17.89 times that of the GF-SEF system. Moreover, the HO• content and organics degradation rate in the MoS2 @GF-SEF are 3.61 and 5.30 times those of the GF-SEF, respectively. This study provides a practical cathode strategy of H* modulation to enhance HO• production and electro-Fenton process. ENVIRONMENTAL IMPLICATION: Boosting Fe2+ regeneration is of great value for the Electro-Fenton process. Herein, report a strategy to achieve this goal based on a MoS2 @GF cathode. Remarkably, the MoS2 @GF system exhibits exceptional efficiency for both various refractory organic compounds with environmentally hazardous effects and sterilization aspects, which can also work over a wide range of pH values (3-11). Specially, this system is driven only by solar energy. These characteristics make the electro-Fenton system more suitable for practical wastewater treatment.

Combined electrochemical and spectroscopic investigations of carbonate-mediated water oxidation to peroxide

The development of electrosynthetic technologies for H2O2 production is appealing from a sustainability perspective. The use of carbonate species as mediators in water oxidation to peroxide has emerged as a viable route to do so but still many questions remain about the mechanism that must be addressed. To this end, this work combines electrochemical and spectroscopic methods to investigate reaction pathways and factors influencing the efficiency of this reaction. Our results indicate that CO32- is the key species that undergoes electrochemical oxidation, prior to reacting with water away from the catalyst. Through spectroelectrochemical experiments, we noted that CO32- depletion is a factor that limits the selectivity of the process. In turn, we showed how the application of pulsed electrolysis can augment this, with an initial set of optimized parameters increasing the selectivity from 20% to 27%. In all, this work helps pave the way for future development of practical H2O2 electrosynthetic systems.

Spaced Double Hydrogen Bonding in an Imidazole Poly Ionic Liquid Composite for Highly Efficient and Selective Photocatalytic Air Reductive H2O2 Synthesis

Photocatalytic oxygen reductive H2O2 production is a promising approach to alternative industrial anthraquinone processes while suffering from the requirement of pure O2 feedstock for practical application. Herein, we report a spaced double hydrogen bond (IC-H-bond) through multi-component Radziszewski reaction in an imidazole poly-ionic-liquid composite (SI-PIL-TiO2) and levofloxacin hydrochloride (LEV) electron donor for highly efficient and selective photocatalytic air reductive H2O2 production. It is found that the IC-H-bond formed by spaced imino (-NH-) group of SI-PIL-TiO2 and carbonyl (-C=O) group of LEV can switch the imidazole active sites characteristic from a covered state to a fully exposed one to shield the strong adsorption of electron donor and N2 in the air, and propel an intenser positive potential and more efficient orbitals binding patterns of SI-PIL-TiO2 surface to establish competitive active sites for selectivity O2 chemisorption. Moreover, the high electron enrichment of imidazole as an active site for the 2e- oxygen reduction ensures the rapid reduction of O2. Therefore, the IC-H-bond enables a total O2 utilization and conversion efficiency of 94.8 % from direct photocatalytic air reduction, achieving a H2O2 production rate of 1518 μmol/g/h that is 16 and 23 times compared to poly-ionic-liquid composite without spaced imino groups (PIL-TiO2) and TiO2, respectively.

Time Constant Estimation and Alleviation of Interior Charge Recombination for Photocatalytic Reaction Guided by Correlation with Photoelectrochemical Behaviors

Interior charge recombination that inherently competes with the separation of photogenerated charges is crucial to the photocatalytic utilization of incident photons. We here propose to simultaneously promote both the desired hole extraction and semiconductor-cocatalyst interfacial electron transfer and suppress the undesired interior charge recombination by shifting the equilibrium potential of the semiconductor in an actual photocatalytic reaction. By correlating with these interfacial electronic processes, we estimate the time constants for the occurrence of interior charge recombination, which range from several milliseconds to several deciseconds in the actual photocatalytic reaction. This time scale estimated from photoelectrochemical behaviors not only provides a substantial guide to photocatalytic reaction design but also avoids relying on a very dense photon beam that greatly deviates from actual working conditions to generate discernible optical signals in certain common methods.

Triggering Dual Two-electron Pathway for H2 O2 Generation by Multiple [Bi-O]n Interlayers in Ultrathin Bi12 O17 Cl2 towards Efficient Piezo-self-Fenton Catalysis

Piezo-self-Fenton system (PESF) has been emerging as a promising water treatment technology but suffering from unsatisfied H2 O2 production efficiency. Herein, we rationally design a Bi12 O17 Cl2 piezo-catalyst with multiple [Bi-O]n interlayers towards highly efficient H2 O2 production. The introduction of [Bi3 O4.25 ] layers initiates dual two-electron pathway for H2 O2 generation by altering the interlayer properties. It is found that the additional [Bi3 O4.25 ] layers not only enhance the polarization electric field but also serve as active sites for triggering dual pathways of two-electron O2 reduction and H2 O oxidation reaction for H2 O2 production. Therefore, the Bi12 O17 Cl2 exhibits an ultrahigh rate of H2 O2 generation (7.76 mM h-1  g-1 ) in pure water. Based on the adequate H2 O2 yield, a PESF was constructed for acetaminophen (ACE) degradation with an apparent rate constant of 0.023 min-1 . This work not only presents a potential strategy of tuning the activity of bismuth based piezo-catalysts but also provides a good example on the construction of highly efficient PESF for environmental remediation by using natural mechanical energy.

Organic Upgrading through Photoelectrochemical Reactions: Toward Higher Profits

Aqueous photoelectrochemical (PEC) cells have long been considered a promising technology to convert solar energy into hydrogen. However, the solar-to-H2 (STH) efficiency and cost-effectiveness of PEC water splitting are significantly limited by sluggish oxygen evolution reaction (OER) kinetics and the low economic value of the produced O2 , hindering the practical commercialization of PEC cells. Recently, organic upgrading PEC reactions, especially for alternative OERs, have received tremendous attention, which improves not only the STH efficiency but also the economic effectiveness of the overall reaction. In this review, PEC reaction fundamentals and reactant-product cost analysis of organic upgrading reactions are briefly reviewed, recent advances made in organic upgrading reactions, which are categorized by their reactant substrates, such as methanol, ethanol, glycol, glycerol, and complex hydrocarbons, are then summarized and discussed. Finally, the current status, further outlooks, and challenges toward industrial applications are discussed.

Iron 3D-Orbital Configuration Dependent Electron Transfer for Efficient Fenton-Like Catalysis

Transition metals are excellent active sites to activate peroxymonosulfate (PMS) for water treatment, but the favorable electronic structures governing  reaction mechanism still remain elusive. Herein, the authors construct typical d-orbital configurations on iron octahedral (FeOh ) and tetrahedral (FeTd ) sites in spinel ZnFe2 O4 and FeAl2 O4 , respectively. ZnFe2 O4 (136.58 min-1 F-1 cm2 ) presented higher specific activity than FeAl2 O4 (97.47 min-1 F-1 cm2 ) for tetracycline removal by PMS activation. Considering orbital features of charge amount, spin state, and orbital arrangement by magnetic spectroscopic analysis, ZnFe2 O4 has a larger bond order to decompose PMS. Using this descriptor, high-spin FeOh is assumed to activate PMS mainly to produce nonradical reactive oxygen species (ROS) while high-spin FeTd prefers to induce radical species. This hypothesis is confirmed by the selective predominant ROS of 1 O2 on ZnFe2 O4 and O2 •- on FeAl2 O4 via quenching experiments. Electrochemical determinations reveal that FeOh has superior capability than FeTd for feasible valence transformation of iron cations and fast interfacial electron transfer. DFT calculations further suggest octahedral d-orbital configuration of ZnFe2 O4 is beneficial to enhancing Fe-O covalence for electron exchange. This work attempts to understand the d-orbital configuration-dependent PMS activation to design efficient catalysts.

Covalent organic frameworks bearing Ni active sites for free radical-mediated photoelectrochemical organic transformations

Photoelectrochemical (PEC) organic transformations occurring at anodes are a promising strategy for circumventing the sluggish kinetics of the oxygen evolution reaction. Here, we report a free radical-mediated reaction instead of direct hole transfer occurring at the solid/liquid interface for PEC oxidation of benzyl alcohol (BA) to benzaldehyde (BAD) with high selectivity. A bismuth vanadate (BiVO4) photoanode coated with a 2,2'-bipyridine-based covalent organic framework bearing single Ni sites (Ni-TpBpy) was developed to drive the transformation. Experimental studies reveal that the reaction at the Ni-TpBpy/BiVO4 photoanode followed first-order reaction kinetics, boosting the formation of surface-bound ·OH radicals, which suppressed further BAD oxidation and provided a nearly 100% selectivity and a rate of 80.63 μmol hour-1 for the BA-to-BAD conversion. Because alcohol-to-aldehyde conversions are involved in the valorizations of biomass and plastics, this work is expected to open distinct avenues for producing key intermediates of great value.

The Secret of Nanoarrays toward Efficient Electrochemical Water Splitting: A Vision of Self-Dynamic Electrolyte

Nanoarray electrocatalysts with unique advantage of facilitating gas bubble detachment have garnered significant interest in gas evolution reactions (GERs). Existing research is largely based on a static hypothesis, assuming that buoyancy is the only driving force for the release of bubbles during GERs. However, this hypothesis overlooks the effect of the self-dynamic electrolyte flow, which is induced by the release of mature bubbles and helps destabilize and release the smaller, immature bubbles nearby. Herein, the enhancing effect of self-dynamic electrolyte flow on nanoarray structures is examined. Phase-field simulations demonstrate that the flow field of electrode with arrayed surface focuses shear force directly onto the gas bubble for efficient detachment, due to the flow could pass through voids and channels to bypass the shielding effect. The flow field therefore has a more substantial impact on the arrayed surface than the nanoscale smooth surface in terms of reducing the critical bubble size. To validate this, superaerophobic ferrous-nickel sulfide nanoarrays are fabricated and employed for water splitting, which display improved efficiency for GERs. This study contributes to understanding the influence of self-dynamic electrolyte on GERs and emphasizes that it should be considered when designing and evaluating nanoarray electrocatalysts.

Increasing the Photocatalytic Hydrogen Generation Activity of CdS Nanorods by Introducing Interfacial and Polarization Electric Fields

Cadmium sulfide (CdS) is a photocatalyst widely used for efficient H2 production under visible light irradiation, due to its narrow bandgap and suitable conduction band position. However, the fast recombination of carriers results in their low utilization. In order to improve photocatalytic hydrogen production, it reports the successful introduction of metallic Cd and S vacancies on CdS nanorods (CdS NRs) by a facile in situ chemical reduction method, using a thermal treatment process. This procedure generates interfacial and polarization electric fields, that significantly improve the photocatalytic hydrogen production performance of CdS NRs in sodium sulfide and sodium sulfite aqueous solutions, under visible light irradiation (λ >420 nm). The introduction of these electric fields is believed to improve charge separation and facilitate faster interfacial charge migration, resulting in a significantly optimized catalyst, with a photocatalytic hydrogen evolution rate of up to 10.6 mmol-1  g-1  h-1 with apparent quantum efficiency (AQE) of 12.1% (420 nm), which is 8.5 times higher than that of CdS. This work provides a useful method to introduce metallic and S vacancies on metal sulfide photocatalysts to build local polarization and interfacial electric fields for high-performance photocatalytic H2 production.

Strategies for promoting the degradation of phenol by electro-Fenton: Simultaneously promoting the generation and utilization of H2O2

The use of the electro-Fenton process to continuously generate H2O2 and efficiently degrade organic pollutants is considered a promising technology. The ratio of generation of H2O2 is usually regarded as the critical step; however, how the H2O2 is utilized is also of particular importance. Herein, activated carbon was activated at different temperatures and used to explore the effect of nitrogen doping on the production and utilization of H2O2 in the electro-Fenton-based degradation of organic pollutants. The experimental results indicate that nitrogen-doped activated carbon simultaneously promotes the generation and utilization of H2O2, which is attributed to the regulation of the competition between phenol and O2 adsorption by the doped nitrogen. Nitrogen doping not only improves 2e-ORR selectivity but also aggregates phenol near the cathode to balance the concentrations of phenol and ·OH. Density functional theory (DFT) calculations further confirmed that pyrrole-N as a dopant promoted the adsorption of phenol, while pyridine-N was more favorable for O2 adsorption. The unique balance of nitrogen types possessed by modified activated carbon NAC-750 permits the efficient synergistic generation and utilization of H2O2 in a balanced manner during the degradation of phenol. This work provides a new direction for the rational nitrogen-doping modification of activated carbon for the electro-Fenton-based degradation of organic pollutants.

Conductive Polymer-Inorganic Polythiophene/Cd0.5Zn0.5S Heterojunction with Apace Charge Separation and Strong Light Absorption for Boosting Photocatalytic Activity

In order to utilize the synergistic effect between a conductive polymer and an inorganic semiconductor to efficaciously enhance charge transfer and solve the problem of unsatisfactory performance of a single photocatalyst, thiophene (Th) was polymerized on the Cd0.5Zn0.5S nanoparticle surface to prepare a conductive polymer-inorganic polythiophene/Cd0.5Zn0.5S (PTh/CZS) heterostructrue through a simple in situ oxidation polymerization for the first time. The as-prepared PTh/CZS heterostructures significantly improved photocatalytic TCH degradation and hydrogen production activities. Especially, the 15PTh/CZS sample exhibited the optimal hydrogen production rate (18.45 mmol g-1 h-1), which was 2.51 times higher than pure Cd0.5Zn0.5S nanoparticles. In addition, 15PTh/CZS also showed very fast and efficient photodegradation ability for degrading 88% of TCH in 25 min. Moreover, the degradation rate (0.06229 min-1) was five times more than that of Cd0.5Zn0.5S. The π-π* transition characteristics, high optical absorption coefficient, wide absorption wavelength of PTh, the tight contact interface, and synergistic effect of PTh and Cd0.5Zn0.5S efficiently boosted charge transfer rate and increased the light absorption of PTh/CZS photocatalysts, which greatly enhanced the photocatalytic abilities. Besides, the mechanism of improved photocatalytic activities for TCH degradation and H2 production was also carefully proposed. Undoubtedly, this work would provide new insights into coupling conductive polymers to inorganic photocatalysts for achieving multifunctional applications in the field of photocatalysis.

Design strategies and mechanisms of g-C3N4-based photoanodes for photoelectrocatalytic degradation of organic pollutants in water

Emerging photoelectrocatalytic (PEC) systems integrate the advantages of photocatalysis and electrocatalysis and are considered as a promising technology for solving the global organic pollution problem in water environments. Among the photoelectrocatalytic materials applied for organic pollutant degradation, graphitic carbon nitride (CN) has the combined advantages of environmental compatibility, stability, low cost, and visible light response. However, pristine CN has disadvantages such as low specific surface area, low electrical conductivity, and high charge complexation rate, and how to improve the degradation efficiency of PEC reaction and the mineralization rate of organic matter is the main problem faced in this field. Therefore, this paper reviews the progress of various functionalized CN used for PEC reaction in recent years, and the degradation efficiency of these CN-based materials is critically evaluated. First, the basic principles of PEC degradation of organic pollutants are outlined. Then, engineering strategies to enhance the PEC activity of CN (including morphology control, elemental doping, and heterojunction construction) are focused on, and the structure-activity relationships between these engineering strategies and PEC activity are discussed. In addition, the important role of influencing factors on the PEC system is summarized in terms of mechanism, to provide guidance for the subsequent research. Finally, suggestions and perspectives are provided for the preparation of efficient and stable CN-based photoelectrocatalysts for practical wastewater treatment applications.

Photocatalytic Self-Fenton System of g-C3N4-Based for Degradation of Emerging Contaminants: A Review of Advances and Prospects

The discharge of emerging pollutants in the industrial process poses a severe threat to the ecological environment and human health. Photocatalytic self-Fenton technology combines the advantages of photocatalysis and Fenton oxidation technology through the in situ generation of hydrogen peroxide (H2O2) and interaction with iron (Fe) ions to generate a large number of strong reactive oxygen species (ROS) to effectively degrade pollutants in the environment. Graphite carbon nitride (g-C3N4) is considered as the most potential photocatalytic oxygen reduction reaction (ORR) photocatalyst for H2O2 production due to its excellent chemical/thermal stability, unique electronic structure, easy manufacturing, and moderate band gap (2.70 eV). Hence, in this review, we briefly introduce the advantages of the photocatalytic self-Fenton and its degradation mechanisms. In addition, the modification strategy of the g-C3N4-based photocatalytic self-Fenton system and related applications in environmental remediation are fully discussed and summarized in detail. Finally, the prospects and challenges of the g-C3N4-based photocatalytic self-Fenton system are discussed. We believe that this review can promote the construction of novel and efficient photocatalytic self-Fenton systems as well as further application in environmental remediation and other research fields.

Regulation of Redox Molecular Junctions in Covalent Organic Frameworks for H2 O2 Photosynthesis Coupled with Biomass Valorization

H2 O2 photosynthesis coupled with biomass valorization can not only maximize the energy utilization but also realize the production of value-added products. Here, a series of COFs (i.e. Cu3 -BT-COF, Cu3 -pT-COF and TFP-BT-COF) with regulated redox molecular junctions have been prepared to study H2 O2 photosynthesis coupled with furfuryl alcohol (FFA) photo-oxidation to furoic acid (FA). The FA generation efficiency of Cu3 -BT-COF was found to be 575 mM g-1 (conversion ≈100 % and selectivity >99 %) and the H2 O2 production rate can reach up to 187 000 μM g-1 , which is much higher than Cu3 -pT-COF, TFP-BT-COF and its monomers. As shown by theoretical calculations, the covalent coupling of the Cu cluster and the thiazole group can promote charge transfer, substrate activation and FFA dehydrogenation, thus boosting both the kinetics of H2 O2 production and FFA photo-oxidation to increase the efficiency. This is the first report about COFs for H2 O2 photosynthesis coupled with biomass valorization, which might facilitate the exploration of porous-crystalline catalysts in this field.

Fabrication of novel BiPO4/Ag3PO4@rGO hybrid composite for effective detoxification of tetracycline

A practical photocatalytic method using efficient and nontoxic is crucial for wastewater treatment technology. The present study deals with the preparation of BiPO₄/Ag₃PO₄@rGO heterojunction through hydrothermal process and utilized it for efficient degradation and detoxification of Tetracycline (TCL) antibiotic. The prepared composite was characterized by X-ray diffraction, UV-vis DRS spectroscopy, Scanning electron microscope (SEM), Transmission electron microscope (TEM) and XPS (X-ray photoelectron spectroscopy). From our study, it was evident that the addition of Ag₃PO₄ extensively improved the photocatalytic efficiency of BiPO₄ with a degradation of the rate of 94.6% (k = 0.01783 min^-1) towards TCL under visible light within 90 min irradiation. The heterojunction energy-band theory has been adopted to understand the mechanism of degradation. The improved efficiency was ascribed to the excellent charge transfer between the interface of p-n heterojunction and the improvement in the absorption of light. Furthermore, LC/ESI-MS/MS (liquid chromatography-electrospray ionization tandem mass spectrometry) carried out TCL degradation product identification to propose the degradation pathway. The biotoxicity assessment studies revealed that effective detoxification was observed during degradation. Thus, this work extends new methods for developing new BiPO₄-based heterojunction composites to meet the requirements for remediation of a contaminated aqueous environment.

Degradation of methyl orange by dielectric films based on contact-electro-catalysis

Contact-electro-catalysis (CEC) has been recently proposed for the effective degradation of methyl orange, but the reactivity of catalysts in the CEC process needs further investigation. Here, we have used dielectric films, such as fluorinated ethylene propylene (FEP), modified by inductively coupled plasma (ICP) etching with argon, to replace the previously employed micro-powder due to their potential scalability, facile recycling process, and possible lower generation of secondary pollution. It has been found that ICP creates cone-like micro/nano structures on the surface, and thus changes the contact angle and specific surface area. The value of the contact angle varies non-linearly with etching time and attains a maximum after 60 seconds of etching. Concurrently, an increased electron transfer is observed, as well as an enhanced degradation efficiency, thus suggesting a special role of the surface structure. Finally, KPFM measurements show a lower electron affinity at the summit of the nanocones. This observation suggests that the structures are endowed with higher charge transfer ability. In addition, this film-based CEC has been observed in several polymer materials, such as PET, PTFE, and PVC. We view this work as a stepping stone to develop CEC into scalable applications, based on film technologies.

A Conformal Carbon Nanolayer Coated Fe2 O3 Cocatalyst for the Promoted Activity of Plasma-Sputtered BiVO4 Photoanode

To simultaneously improve the hole extraction ability of the BiVO₄ photoanode and accelerate the surface reaction kinetics, herein, a carbon nanolayer conformally coated Fe₂ O₃ (C-Fe₂ O₃ ) as oxygen evolution catalyst (OEC) is loaded on the H₂ plasma treated nanoporous BiVO₄ (BVO(H₂ )) surface by a hydrothermal reaction. It is found that the H₂ plasma induced vacancies in BVO remarkably increases the conductivity, and the C-Fe₂ O₃ enables hole extraction from the bulk to the surface as well as efficient hole injection to the electrolyte. As a result, the C-Fe₂ O₃ /BVO(H₂ ) photoanode achieves a photocurrent density of 4.4 mA/cm² at 1.23 V vs. reversible hydrogen electrode (RHE) and an ABPE value of 1.5 % at 0.68 V vs. RHE, which are 4.8-fold and 13-fold higher than that of BVO photoanode, respectively.

Solar-to-H2 O2 Energy Conversion by the Photothermal Effect of a Polymeric Photocatalyst via a Two-Channel Pathway

With a view to using solar energy, the exploitation of near-infrared (NIR) light, which constitutes about 50 % of solar energy, in photocatalytic H₂ O₂ synthesis remains challenging. In this study, resorcinol-formaldehyde (RF), which has a relatively low bandgap and high conductivity, is introduced for photothermal catalytic generation of H₂ O₂ under ambient conditions. Owing to the promoted surface charge transfer rate under high temperature, the photosynthetic yield reaches roughly 2000 μm within 40 min under 400 mW cm^-2 irradiation with a solar-to-chemical conversion (SCC) efficiency of up to 0.19 % at 338 K under ambient conditions, exceeding the rate of photocatalysis with a cooling system by a factor of about 2.5. Notably, the H₂ O₂ produced by RF during photothermal process was formed via a two-channel pathway, leading to the overall promotion of H₂ O₂ formation. The resultant H₂ O₂ can be applied in situ for pollutant removal. This work offers a sustainable and economical route for the efficient formation of H₂ O₂ .

Oxidation-Reduction Molecular Junction Covalent Organic Frameworks for Full Reaction Photosynthesis of H2 O2

The full reaction photosynthesis of H₂ O₂ that can combine water-oxidation and oxygen-reduction without sacrificial agents is highly demanded to maximize the light-utilization and overcome the complex reaction-process of anthraquinone-oxidation. Here, a kind of oxidation-reduction molecular junction covalent-organic-framework (TTF-BT-COF) has been synthesized through the covalent-coupling of tetrathiafulvalene (photo-oxidation site) and benzothiazole (photo-reduction site), which presents visible-light-adsorption region, effective electron-hole separation-efficiency and photo-redox sites that enables full reaction generation of H₂ O₂ . Specifically, a record-high yield (TTF-BT-COF, ≈276 000 μM h^-1  g^-1 ) for H₂ O₂ photosynthesis without sacrificial agents has been achieved among porous crystalline photocatalysts. This is the first work that can design oxidation-reduction molecular junction COFs for full reaction photosynthesis of H₂ O₂ , which might extend the scope of COFs in H₂ O₂ production.

Boosting Reactive Oxygen Species Generation Using Inter-Facet Edge Rich WO3 Arrays for Photoelectrochemical Conversion

Water oxidation reaction leaves room to be improved in the development of various solar fuel productions, because of the kinetically sluggish 4-electron transfer process of oxygen evolution reaction. In this work, we realize reactive oxygen species (ROS), H₂ O₂ and OH⋅, formations by water oxidation with total Faraday efficiencies of more than 90 % by using inter-facet edge (IFE) rich WO₃ arrays in an electrolyte containing CO₃ ^2- . Our results demonstrate that the IFE favors the adsorption of CO₃ ^2- while reducing the adsorption energy of OH⋅, as well as suppresses surface hole accumulation by direct 1-electron and indirect 2-electron transfer pathways. Finally, we present selective oxidation of benzyl alcohol by in situ using the formed OH⋅, which delivers a benzaldehyde production rate of ≈768 μmol h^-1 with near 100 % selectivity. This work offers a promising approach to tune or control the oxidation reaction in an aqueous solar fuel system towards high efficiency and value-added product.