Flexible layer-structured Bi2Te3 thermoelectric on a carbon nanotube scaffold

Controlled synthesis, properties, and applications of ultralong carbon nanotubes

Carbon nanotubes (CNTs) are typical one-dimensional nanomaterials which have been widely studied for more than three decades since 1991 because of their excellent mechanical, electrical, thermal, and optical properties. Among various types of CNTs, the ultralong CNTs which have lengths over centimeters and defect-free structures exhibit superior advantages for fabricating superstrong CNT fibers, CNT-based chips, transparent conductive films, and high-performance cables. The length, orientation, alignment, defects, cleanliness, and other microscopic characteristics of CNTs have significant impacts on their fundamental physical properties. Therefore, the controlled synthesis and mass production of high-quality ultralong CNTs is the key to fully exploiting their extraordinary properties. Despite significant progress made in the study of ultralong CNTs during the past three decades, the precise structural control and mass production of ultralong CNTs remain a great challenge. In this review, we systematically summarize the growth mechanism and controlled synthesis strategies of ultralong CNTs. We also introduce the progress in the applications of ultralong CNTs. Additionally, we summarize the scientific and technological challenges facing the mass production of ultralong CNTs and provide an outlook and in-depth discussion on the future development direction.

Enhancing Thermoelectric and Cooling Performance of Bi0.5Sb1.5Te3 through Ferroelectric Polarization in Flexible Ag/PZT/PVDF/Bi0.5Sb1.5Te3 Film

Bi2Te3-based thin films are gaining recognition for their remarkable room temperature thermoelectric performance. Beyond the conventional "process-composition-performance" paradigm, it is highly desirable to explore new methods to enhance their performance further. Here, we designed a sandwich-structured Ag/PZT/PVDF/Bi0.5Sb1.5Te3(BST) thin film device and effectively regulated the performance of the BST film by controlling the polarization state of the PZT/PVDF layers. Results indicate that polarization induces interlayer charge redistribution and charge transfer between PZT/PVDF and BST, thereby achieving the continuous modulation of the electrical transport characteristics of BST films. Finally, following polarization at a saturation voltage of 3 kV, the power factor of the BST film increased by 13% compared to the unpolarized condition, reaching 20.8 μW cm-1 K-2. Furthermore, a device with 7 pairs of P-N legs was fabricated, achieving a cooling temperature difference of 11.0 K and a net cooling temperature difference of 2.4 K at a current of 10 mA after the saturation polarization of the PZT/PVDF layer. This work reveals the critical effect of introducing ferroelectric layer polarization to achieve excellent thermoelectric performance of the BST film.

Multi-heterojunctioned plastics with high thermoelectric figure of merit

Conjugated polymers promise inherently flexible and low-cost thermoelectrics for powering the Internet of Things from waste heat1,2. Their valuable applications, however, have been hitherto hindered by the low dimensionless figure of merit (ZT)3-6. Here we report high-ZT thermoelectric plastics, which were achieved by creating a polymeric multi-heterojunction with periodic dual-heterojunction features, where each period is composed of two polymers with a sub-ten-nanometre layered heterojunction structure and an interpenetrating bulk-heterojunction interface. This geometry produces significantly enhanced interfacial phonon-like scattering while maintaining efficient charge transport. We observed a significant suppression of thermal conductivity by over 60 per cent and an enhanced power factor when compared with individual polymers, resulting in a ZT of up to 1.28 at 368 kelvin. This polymeric thermoelectric performance surpasses that of commercial thermoelectric materials and existing flexible thermoelectric candidates. Importantly, we demonstrated the compatibility of the polymeric multi-heterojunction structure with solution coating techniques for satisfying the demand for large-area plastic thermoelectrics, which paves the way for polymeric multi-heterojunctions towards cost-effective wearable thermoelectric technologies.

Ductile P-Type AgCu(Se,S,Te) Thermoelectric Materials

Ductile inorganic thermoelectric (TE) materials open a new approach to develop high-performance flexible TE devices. N-type Ag2(S,Se,Te) and p-type AgCu(Se,S,Te) pseudoternary solid solutions are two typical categories of ductile inorganic TE materials reported so far. Comparing with the Ag2(S,Se,Te) pseudoternary solid solutions, the phase composition, crystal structure, and physical properties of AgCu(Se,S,Te) pseudoternary solid solutions are more complex, but their relationships are still ambiguous now. In this work, via systematically investigating the phase composition, crystal structure, mechanical, and TE properties of about 60 AgCu(Se,S,Te) pseudoternary solid solutions, the comprehensive composition-structure-property phase diagrams of the AgCuSe-AgCuS-AgCuTe pseudoternary system is constructed. By mapping the complex phases, the "ductile-brittle" and "n-p" transition boundaries are determined and the composition ranges with high TE performance and inherent ductility are illustrated. On this basis, high performance p-type ductile TE materials are obtained, with a maximum zT of 0.81 at 340 K. Finally, flexible in-plane TE devices are prepared by using the AgCu(Se,S,Te)-based ductile TE materials, showing high output performance that is superior to those of organic and inorganic-organic hybrid flexible devices.

Evoking natural thermal perceptions using a thin-film thermoelectric device with high cooling power density and speed

Multimodal sensory feedback from upper-limb prostheses can increase their function and usability. Here we show that intuitive thermal perceptions during cold-object grasping with a prosthesis can be restored in a phantom hand through targeted nerve stimulation via a wearable thin-film thermoelectric device with high cooling power density and speed. We found that specific regions of the residual limb, when thermally stimulated, elicited thermal sensations in the phantom hand that remained stable beyond 48 weeks. We also found stimulation sites that selectively elicited sensations of temperature, touch or both, depending on whether the stimulation was thermal or mechanical. In closed-loop functional tasks involving the identification of cold objects by amputees and by non-amputee participants, and compared with traditional bulk thermoelectric devices, the wearable thin-film device reliably elicited cooling sensations that were up to 8 times faster and up to 3 times greater in intensity while using half the energy and 1/600th the mass of active thermoelectric material. Wearable thin-film thermoelectric devices may allow for the non-invasive restoration of thermal perceptions during touch.

High Power Factor Flexible Ag2Te Film on Nylon by a Wet Chemical Method for Power Generator

Herein, we develop a facile wet chemical method for the synthesis of Ag2Te powders at room temperature and flexible Ag2Te/nylon thermoelectric (TE) films are prepared by vacuum-assisted filtration of the synthesized Ag2Te powders and then hot pressing. Because of the good crystallinity of Ag2Te grains and continuous grain boundaries, an optimized film exhibits a power factor of 513 μW m-1 K-2 at 300 K, which stands among the highest values reported for Ag2Te-based films to date. In addition, the film also has good flexibility. A four-leg flexible TE device assembled with the film generates a power density of 5.46 W m-2 at a temperature gradient of 31.8 K. This work provides a facile and environmentally friendly method for preparing flexible Ag2Te films.

Band Degeneracy and Anisotropy Enhances Thermoelectric Performance from Sb2Si2Te6 to Sc2Si2Te6

The complex interrelationships among thermoelectric parameters mean that a priori design of high-performing materials is difficult. However, band engineering can allow the power factor to be optimized through enhancement of the Seebeck coefficient. Herein, using layered Sb2Si2Te6 and Sc2Si2Te6 as model systems, we comprehensively investigate and compare their thermoelectric properties by employing density functional theory combined with semiclassical Boltzmann transport theory. Our simulations reveal that Sb2Si2Te6 exhibits superior electrical conductivity compared to Sc2Si2Te6 due to lower scattering rates and more pronounced band dispersion. Remarkably, despite Sb2Si2Te6 exhibiting a lower lattice thermal conductivity and superior electrical conductivity, Sc2Si2Te6 is predicted to achieve an extraordinary dimensionless figure of merit (ZT) of 3.51 at 1000 K, which significantly surpasses the predicted maximum ZT of 2.76 for Sb2Si2Te6 at 900 K. We find the origin of this behavior to be a combined increase in band (valley) degeneracy and anisotropy upon switching the conduction band orbital character from Sb p to Sc d, yielding a significantly improved Seebeck coefficient. This work suggests that enhancing band degeneracy and anisotropy (complexity) through compositional variation is an effective strategy for improving the thermoelectric performance of layered materials.

Growth of 1D Carbon Nanotube@Perovskite Core-Shell van der Waals Heterostructures through Chemical Vapor Deposition

Perovskite is an emerging material with immense potential in the field of optoelectronics. 1D perovskite nanowires are crucial building blocks for the development of optoelectronic devices. However, producing perovskite nanowires with high quality and controlled alignment is challenging. In this study, the direct epitaxial growth of perovskite on oriented carbon nanotube (CNT) templates is presented through a chemical vapor deposition method. The deposition process of lead iodide and methylammonium iodide is systematically investigated, and a layer plus island growth mechanism is proposed to interpret the experimental observations. The aligned long CNTs serve as 1D templates and allow the growth of CNT@perovskite core-shell heterostructure with a high aspect ratio to withstand large deformation. The obtained 1D perovskite materials can be easily manipulated and transferred, enabling the facile preparation of microscale flexible devices. For proof of concept, a photodetector based on an individual CNT@methylammonium lead iodide heterostructure is fabricated. This work provides a new approach to prepare 1D hetero-nanostructure and may inspire the design of novel flexible nanophotodetectors.

High-performance flexible p-type Ce-filled Fe3CoSb12 skutterudite thin film for medium-to-high-temperature applications

P-type Fe3CoSb12-based skutterudite thin films are successfully fabricated, exhibiting high thermoelectric performance, stability, and flexibility at medium-to-high temperatures, based on preparing custom target materials and employing advanced pulsed laser deposition techniques to address the bonding challenge between the thin films and high-temperature flexible polyimide substrates. Through the optimization of fabrication processing and nominal doping concentration of Ce, the thin films show a power factor of >100 μW m-1 K-2 and a ZT close to 0.6 at 653 K. After >2000 bending cycle tests at a radius of 4 mm, only a 6 % change in resistivity can be observed. Additionally, the assembled p-type Fe3CoSb12-based flexible device exhibits a power density of 135.7 µW cm-2 under a temperature difference of 100 K with the hot side at 623 K. This work fills a gap in the realization of flexible thermoelectric devices in the medium-to-high-temperature range and holds significant practical application value.

All-Automated Fabrication of Freestanding and Scalable Photo-Thermoelectric Devices with High Performance

Flexible photo-thermoelectric (PTE) devices have great application prospects in the fields of solar energy conversion, ultrabroadband light detection, etc. A suitable manufacturing process to avoid the substrate effects as well as to create a narrow transition area between p-n modules for high-performance freestanding flexible PTE devices is highly desired. Herein, an automated laser fabrication (ALF) method is reported to construct the PTE devices with rylene-diimide-doped n-type single-walled carbon nanotube (SWCNT) films. The wet-compressing approach is developed to improve the thermoelectric power factors and figure of merit (ZT) of the SWCNT hybrid films. Then, the films are cut and patterned automatically to make PTE devices with various structures by the proposed ALF method. The freestanding PTE device with a narrow transition area of ≈2-3 µm between the p and n modules exhibits a high-power density of 0.32 µW cm-2 under the light of 200 mW cm-2, which is among the highest level for freestanding-film-based PTE devices. The results pave the way for the automatic production process of PTE devices for green power generation and ultrabroadband light detection.

Enhancement of ZT in Bi0.5Sb1.5Te3 Thin Film through Lattice Orientation Management

Thermoelectric power can convert heat and electricity directly and reversibly. Low-dimensional thermoelectric materials, particularly thin films, have been considered a breakthrough for separating electronic and thermal transport relationships. In this study, a series of Bi0.5Sb1.5Te3 thin films with thicknesses of 0.125, 0.25, 0.5, and 1 μm have been fabricated by RF sputtering for the study of thickness effects on thermoelectric properties. We demonstrated that microstructure (texture) changes highly correlate with the growth thickness in the films, and equilibrium annealing significantly improves the thermoelectric performance, resulting in a remarkable enhancement in the thermoelectric performance. Consequently, the 0.5 μm thin films achieve an exceptional power factor of 18.1 μWcm-1K-2 at 400 K. Furthermore, we utilize a novel method that involves exfoliating a nanosized film and cutting with a focused ion beam, enabling precise in-plane thermal conductivity measurements through the 3ω method. We obtain the in-plane thermal conductivity as low as 0.3 Wm-1K-1, leading to a maximum ZT of 1.86, nearing room temperature. Our results provide significant insights into advanced thin-film thermoelectric design and fabrication, boosting high-performance systems.

Phase-Transition-Promoted Thermoelectric Textiles Based on Twin Surface-Modified CNT Fibers

With the fast development of new science and technology, wearable devices are in great demand in modern human daily life. However, the energy problem is a long-lasting issue to achieve real smart, wearable, and portable devices. Flexible thermoelectric generators (TEGs) based on thermoelectric conversion systems can convert body waste heat into electricity with excellent flexibility and wearability, which shows a new direction to solving this issue. Here in this work, polyethylenimine (PEI) and gold nanoparticles (Au NPs) twin surface-modified carbon nanotube fibers (CNTFs) were designed and prepared to fabricate thermoelectric textiles (TET) with high performance, good air stability, and high-efficiency power generation. To better utilize the heat emitted by the human body, microencapsulated phase change materials (MPCM) were coated on the hot end of the TET to achieve the phase-transition-promoted TET. MPCM-coated TET device could generate 25.7% more energy than the untreated control device, which indicates the great potential of the phase-transition-promoted TET.

Facile Fabrication of Flexible and High-Performing Thermoelectrics by Direct Laser Printing on Plastic Foil

The emerging fields of wearables and the Internet of Things introduce the need for electronics and power sources with unconventional form factors: large area, customizable shape, and flexibility. Thermoelectric (TE) generators can power those systems by converting abundant waste heat into electricity, whereas the versatility of additive manufacturing suits heterogeneous form factors. Here, additive manufacturing of high-performing flexible TEs is proposed. Maskless and large-area patterning of Bi2Te3-based films is performed by laser powder bed fusion directly on plastic foil. Mechanical interlocking allows simultaneous patterning, sintering, and attachment of the films to the substrate without using organic binders that jeopardize the final performance. Material waste could be minimized by recycling the unexposed powder. The particular microstructure of the laser-printed material renders the-otherwise brittle-Bi2Te3 films highly flexible despite their high thickness. The films survive 500 extreme-bending cycles to a 0.76 mm radius. Power factors above 1500 µW m-1K-2 and a record-low sheet resistance for flexible TEs of 0.4 Ω sq-1 are achieved, leading to unprecedented potential for power generation. This versatile fabrication route enables innovative implementations, such as cuttable arrays adapting to specific applications in self-powered sensing, and energy harvesting from unusual scenarios like human skin and curved hot surfaces.

Flexible temperature-pressure dual sensor based on 3D spiral thermoelectric Bi2Te3 films

Dual-parameter pressure-temperature sensors are widely employed in personal health monitoring and robots to detect external signals. Herein, we develop a flexible composite dual-parameter pressure-temperature sensor based on three-dimensional (3D) spiral thermoelectric Bi2Te3 films. The film has a (000l) texture and good flexibility, exhibiting a maximum Seebeck coefficient of -181 μV K-1 and piezoresistance gauge factor of approximately -9.2. The device demonstrates a record-high temperature-sensing performance with a high sensing sensitivity (-426.4 μV K-1) and rapid response time (~0.95 s), which are better than those observed in most previous studies. In addition, owing to the piezoresistive effect in the Bi2Te3 film, the 3D-spiral deviceexhibits significant pressure-response properties with a pressure-sensing sensitivity of 120 Pa-1. This innovative approach achieves high-performance dual-parameter sensing using one kind of material with high flexibility, providing insight into the design and fabrication of many applications, such as e-skin.

Fully inkjet-printed Ag2Se flexible thermoelectric devices for sustainable power generation

Flexible thermoelectric devices show great promise as sustainable power units for the exponentially increasing self-powered wearable electronics and ultra-widely distributed wireless sensor networks. While exciting proof-of-concept demonstrations have been reported, their large-scale implementation is impeded by unsatisfactory device performance and costly device fabrication techniques. Here, we develop Ag2Se-based thermoelectric films and flexible devices via inkjet printing. Large-area patterned arrays with microscale resolution are obtained in a dimensionally controlled manner by manipulating ink formulations and tuning printing parameters. Printed Ag2Se-based films exhibit (00 l)-textured feature, and an exceptional power factor (1097 μWm-1K-2 at 377 K) is obtained by engineering the film composition and microstructure. Benefiting from high-resolution device integration, fully inkjet-printed Ag2Se-based flexible devices achieve a record-high normalized power (2 µWK-2cm-2) and superior flexibility. Diverse application scenarios are offered by inkjet-printed devices, such as continuous power generation by harvesting thermal energy from the environment or human bodies. Our strategy demonstrates the potential to revolutionize the design and manufacture of multi-scale and complex flexible thermoelectric devices while reducing costs, enabling them to be integrated into emerging electronic systems as sustainable power sources.

Bioinspired Hollow/Hollow Architecture with Flourishing Dielectric Properties for Efficient Electromagnetic Energy Reclamation Device

The exploitation of advanced electromagnetic functional devices is perceived as the effective prescription to deal with environmental contamination and energy deficiency. From the perspective of observing and imitating nature, pine branch-like zirconium dioxide/cobalt nanotubes@nitrogen-doped carbon nanotubes are synthesized victoriously through maneuverable electrospinning process and follow-up thermal treatments. In particular, introducing carbon nanotubes on the surface of hollow nanofibers to construct hierarchical architecture vastly promoted the material's dielectric properties by significantly augmenting specific surface area, generating abundant heterogeneous interfaces, and inducing the formation of defects. Supplemented by the synergistic effect between each constituent, ultra-strong attenuation capacity and perfect impedance matching characteristics are implemented simultaneously, and jointly made contributions to the splendid microwave absorption performance with a minimum reflection loss of -67.9 dB at 1.5 mm. Moreover, this fibrous absorber also exhibited promising potential to be utilized as a green and efficient electromagnetic interference shielding material when the filler loading is enhanced. Therefore, this design philosophy is destined to inspire the future development of energy conversion and storage devices, and provide theoretical direction for the creation of sophisticated electromagnetic functional materials.

Ultralow-Overpotential Acidic Oxygen Evolution Reaction Over Bismuth Telluride-Carbon Nanotube Heterostructure with Organic Framework

The state-of-the-art iridium and ruthenium oxides-based materials are best known for high efficiency and stability in acidic oxygen evolution reaction (OER). However, the development of economically feasible catalysts for water-splitting technologies is challenging by the requirements of low overpotential, high stability, and resistance of catalysts to dissolution during the acidic oxygen evolution reaction . Herein, an organometallic core-shell heterostructure composed of a carbon nanotube core (CNT) and bismuth telluride (Bi2Te3) shell (denoted as nC-Bi2Te3) is designed and use it as a catalyst for the acidic OER. The proposed catalyst achieves an ultralow overpotential of 160 mV at 10 mA cm-2 (geometrical), thereby outperforming most of the state-of-the-art precious-metal-based catalysts. The low Tafel slope of 30 mV dec-1 and charge transfer resistance (RCT) of 1.5 Ω demonstrate its excellent electrocatalytic activity. The morphological and chemical compositions of nC-Bi2Te3 enable the generation of ─OH functional group in the Bi─Te sections formed via a ligand support, which enhances the absorption capacity of H+ ions and increases the intrinsic catalytic activity. The presented insights regarding the material composition-structure relationship can help expand the application scope of high-performance catalysts.

Thermoelectric Generator Through Dual-Direction Thermal Regulation by Thermal Diodes for Waste Heat Harvesting

Thermal energy harvesting provides an opportunity for multi-node systems to achieve self-power autonomy. Thermoelectric generators (TEGs), either by thermocouple arrangement with higher-aspect-ratios or thermoelectric films overlay, are limited by the small temperature difference and its short-duration (less than dozens of minutes), hindering the harvesting efficiency. Here, by introducing thermal diodes with dual-direction thermal regulation ability to optimize the heat flux path, the proposed TEGs exhibit enhanced power-supply capability with unprecedented long-duration (more than hours). In contrast with conventional TEGs with fixed-leg dimensions enabled single output, these compact-TEGs can supply up to fourteen output-channels for selection, the produced power ranges from 1.11 to 921.99 µW, open circuit voltage ranges from 8.07 to 51.32 mV, when the natural temperature difference is 53.84 °C. Compared to the most recent TEGs, the proposed TEGs in this study indicate higher power (more than hundreds times) and much longer output duration (2.4-120 times) in a compact manner.

On-Chip Micro Temperature Controllers Based on Freestanding Thermoelectric Nano Films for Low-Power Electronics

Multidimensional integration and multifunctional component assembly have been greatly explored in recent years to extend Moore's Law of modern microelectronics. However, this inevitably exacerbates the inhomogeneity of temperature distribution in microsystems, making precise temperature control for electronic components extremely challenging. Herein, we report an on-chip micro temperature controller including a pair of thermoelectric legs with a total area of 50 × 50 μm2, which are fabricated from dense and flat freestanding Bi2Te3-based thermoelectric nano films deposited on a newly developed nano graphene oxide membrane substrate. Its tunable equivalent thermal resistance is controlled by electrical currents to achieve energy-efficient temperature control for low-power electronics. A large cooling temperature difference of 44.5 K at 380 K is achieved with a power consumption of only 445 μW, resulting in an ultrahigh temperature control capability over 100 K mW-1. Moreover, an ultra-fast cooling rate exceeding 2000 K s-1 and excellent reliability of up to 1 million cycles are observed. Our proposed on-chip temperature controller is expected to enable further miniaturization and multifunctional integration on a single chip for microelectronics.

Flexible Ag2Se Thermoelectric Films Enable the Multifunctional Thermal Perception in Electronic Skins

Skin is critical for shaping our interactions with the environment. The electronic skin (E-skin) has emerged as a promising interface for medical devices to replicate the functions of damaged skin. However, exploration of thermal perception, which is crucial for physiological sensing, has been limited. In this work, a multifunctional E-skin based on flexible thermoelectric Ag2Se films is proposed, which utilizes the Seebeck effect to replicate the sensory functions of natural skin. The E-skin can enable capabilities including temperature perception, tactile perception, contactless perception, and material recognition by analyzing the thermal conduction behaviors of various materials. To further validate the capabilities of constructed E-skins, a wearable device with multiple sensory channels was fabricated and tested for gesture recognition. This work highlights the potential for using flexible thermoelectric materials in advanced biomedical applications including health monitoring and smart prosthetics.

Significant Enhancement of Thermoelectric Performance in Bi0.5 Sb1.5 Te3 Thin Film via Ferroelectric Polarization Engineering

The Bi0.5 Sb1.5 Te3 (BST) thin film shows great promise in harvesting low-grade heat energy due to its excellent thermoelectric performance at room temperature. In order to further enhance its thermoelectric performance, specifically the power factor and output power, new approaches are highly desirable beyond the common "composition-structure-performance" paradigm. This study introduces ferroelectric polarization engineering as a novel strategy to achieve these goals. A Pb(Zr0.52 Ti0.48 )O3 /Bi0.5 Sb1.5 Te3 (PZT/BST) hybrid film is fabricated via magnetron sputtering. Density functional theory calculations demonstrate PZT polarization's influence on charge redistribution and interlayer charge transfer at the PZT/BST interface, facilitating adjustable carrier transport behavior and power factor of the BST film. As a result, a 26.7% enhancement of the power factor, from unpolarized 12.0 to 15.2 µW cm-1 K-2 , is reached by 2 kV out-of-plane downward polarization of PZT. Furthermore, a five-leg generator constructed using this PZT/BST hybrid film exhibits a maximum output power density of 13.06 W m-2 at ΔT = 39 K, which is 20.8% higher than that of the unpolarized one (10.81 W m-2 ). The research presents a new approach to enhance thermoelectric thin films' power factor and output performance by introducing ferroelectric polarization engineering.

Pulse irradiation synthesis of metal chalcogenides on flexible substrates for enhanced photothermoelectric performance

High synthesis temperatures and specific growth substrates are typically required to obtain crystalline or oriented inorganic functional thin films, posing a significant challenge for their utilization in large-scale, low-cost (opto-)electronic applications on conventional flexible substrates. Here, we explore a pulse irradiation synthesis (PIS) to prepare thermoelectric metal chalcogenide (e.g., Bi2Se3, SnSe2, and Bi2Te3) films on multiple polymeric substrates. The self-propagating combustion process enables PIS to achieve a synthesis temperature as low as 150 °C, with an ultrafast reaction completed within one second. Beyond the photothermoelectric (PTE) property, the thermal coupling between polymeric substrates and bismuth selenide films is also examined to enhance the PTE performance, resulting in a responsivity of 71.9 V/W and a response time of less than 50 ms at 1550 nm, surpassing most of its counterparts. This PIS platform offers a promising route for realizing flexible PTE or thermoelectric devices in an energy-, time-, and cost-efficient manner.

Interface Engineering for High-Performance Thermoelectric Carbon Nanotube Films

Carbon nanotubes (CNTs) stand out for their exceptional electrical, thermal, and mechanical attributes, making them highly promising materials for cutting-edge, lightweight, and flexible thermoelectric applications. However, realizing the full potential of advanced thermoelectric CNTs requires precise management of their electrical and thermal characteristics. This study, through interface optimization, demonstrates the feasibility of reducing the thermal conductivity while preserving robust electrical conductivity in single-walled CNT films. Our findings reveal that blending two functionalized CNTs offers a versatile method of tailoring the structural and electronic properties of CNT films. Moreover, the modified interface exerts a substantial influence over thermal and electrical transfer, effectively suppressing heat dissipation and facilitating thermoelectric power generation within CNT films. As a result, we have successfully produced both p- and n-type thermoelectric CNTs, attaining impressive power factors of 507 and 171 μW/mK2 at room temperature, respectively. These results provide valuable insights into the fabrication of high-performance thermoelectric CNT films.

Synthesis and enhanced room-temperature thermoelectric properties of CuO-MWCNT hybrid nanostructured composites

This work presents the synthesis of novel copper oxide-multiwalled carbon nanotube (CuO-MWCNT) hybrid nanostructured composites and a systematic study of their thermoelectric performance at near-room temperatures as a function of MWCNT wt% in the composite. The CuO-MWCNT hybrid nanostructured composites were synthesized by thermal oxidation of a thin metallic Cu layer pre-deposited on the MWCNT network. This resulted in the complete incorporation of MWCNTs in the nanostructured CuO matrix. The thermoelectric properties of the fabricated CuO-MWCNT composites were compared with the properties of CuO-MWCNT networks prepared by mechanical mixing and with the properties of previously reported thermoelectric [CuO]99.9[SWCNT]0.1 composites. CuO-MWCNT hybrid composites containing MWCNTs below 5 wt% showed an increase in the room-temperature thermoelectric power factor (PF) by ∼2 times compared with a bare CuO nanostructured reference thin film, by 5-50 times compared to mixed CuO-MWCNT networks, and by ∼10 times the PF of [CuO]99.9[SWCNT]0.1. The improvement of the PF was attributed to the changes in charge carrier concentration and mobility due to the processes occurring at the large-area CuO-MWCNT interfaces. The Seebeck coefficient and PF reached by the CuO-MWCNT hybrid nanostructured composites were 688 μV K-1 and ∼4 μW m-1 K-2, which exceeded the recently reported values for similar composites based on MWCNTs and the best near-room temperature inorganic thermoelectric materials such as bismuth and antimony chalcogenides and highlighted the potential of CuO-MWCNT hybrid nanostructured composites for applications related to low-grade waste heat harvesting and conversion to useable electricity.

Thermoelectrics and thermocells for fire warning applications

Historically, fire disasters have killed numerous human lives, and caused tremendous property loss. Fire warning systems play a vital role in predicting fire risks, and are strongly desired to effectively prevent the disaster occurrence and significantly reduce the loss. Among the developed fire warning systems, thermoelectrics (TEs) and thermocells (TECs)-based fire warning materials are extremely important and indispensable in future research, owing to their unique capability of direct conversion between heat and electricity. Here, we present this review of the recent progress of TEs and TECs in fire warning field. Firstly, a brief introduction of existing fire warning systems is provided, including the mechanisms and features of various types. Then, the mechanisms of electronic TE (eTE), ionic TE (iTE) and TEC are elucidated. Next, the basic principles for the material preparation and device fabrication are discussed in their dimension sequence. Subsequently, some important advances or examples of TE fire warnings are highlighted in details. Finally, the challenges and prospects are outlooked.

Densification Induced Decoupling of Electrical and Thermal Properties in Free-Standing MWCNT Films for Ultrahigh p- and n-Type Power Factors and Enhanced ZT

Generating sufficient power from waste heat is one of the most important things for thermoelectric (TE) techniques in numerous practical applications. The output power density of an organic thermoelectric generator (OTEG) is proportional to the power factors (PFs) and the electrical conductivities of organic materials. However, it is still challenging to have high PFs over 1 mW m-1  K-2 in free-standing films together with high electrical conductivities over 1000 S cm-1 . Herein, densifying multi-walled carbon nanotube (MWCNT) films would increase their electrical conductivity dramatically up to over 10 000 S cm-1 with maintained high Seebeck coefficients >60 µV K-1 , thus leading to ultrahigh PFs of 7.25 and 4.34 mW m-1  K-2 for p- and n-type MWCNT films, respectively. In addition, it is interesting to notice that the electrical properties increase faster than the thermal conductivities, resulting in enhanced ZT of 3.6 times in MWCNT films. An OTEG made of compressed MWCNT films is fabricated to demonstrate the heat-to-electricity conversion ability, which exhibits a high areal output power of ∼12 times higher than that made of pristine MWCNT films. This work demonstrates an effective way to high-performance nanowire/nanoparticle-based TE materials such as printable TE materials comprised of nanowires/nanoparticles.

Solvent-assisted synthesis of Ag2Se and Ag2S nanoparticles on carbon fabric for enhanced thermoelectric performance

The challenge of developing low-cost, highly flexible, and high-performance thermoelectric (TE) materials persists due to the low thermoelectric efficiency of conducting polymers and the inflexibility of inorganic materials. In this study, we successfully integrated Ag2Se and Ag2S with highly conductive carbon fabric (CF) to produce a flexible thermoelectric material. A facile one-step solvothermal method was employed to synthesize the Ag2Se-CF and Ag2S-CF, which were then subjected to X-ray analysis to confine the phase formation of Ag2Se and Ag2S on the carbon fabric. The analysis revealed that Ag2Se and Ag2S nanoparticles were tightly packed on the surface of carbon fabric, and compositional analysis confirmed the interaction between the material and carbon fabric. The thermoelectric properties of Ag2Se-CF and Ag2S-CF were significantly altered due to carrier concentration and mobility variations, resulting in a low power factor of 6.7 μW/mK2 for Ag2Se-CF and a high-power factor of 24 μW/mK2 at 373 K for Ag2S-CF. The growth of Ag2Se-CF and Ag2S-CF on carbon fabric led to an enhancement in their thermoelectric properties. Further, TE legs were fabricated using the Ag2Se-CF (p-type) and Ag2S-CF (n-type), and the fabricated legs exhibited an output voltage of ∼20 mV to ∼86.65 mV at a temperature gradient (ΔT) of 3-8 K. This work represents a cutting-edge approach to the fabrication of high-performance, wearable thermoelectric devices.

Self-Powered Sensing in Wearable Electronics─A Paradigm Shift Technology

With the advancements in materials science and micro/nanoengineering, the field of wearable electronics has experienced a rapid growth and significantly impacted and transformed various aspects of daily human life. These devices enable individuals to conveniently access health assessments without visiting hospitals and provide continuous, detailed monitoring to create comprehensive health data sets for physicians to analyze and diagnose. Nonetheless, several challenges continue to hinder the practical application of wearable electronics, such as skin compliance, biocompatibility, stability, and power supply. In this review, we address the power supply issue and examine recent innovative self-powered technologies for wearable electronics. Specifically, we explore self-powered sensors and self-powered systems, the two primary strategies employed in this field. The former emphasizes the integration of nanogenerator devices as sensing units, thereby reducing overall system power consumption, while the latter focuses on utilizing nanogenerator devices as power sources to drive the entire sensing system. Finally, we present the future challenges and perspectives for self-powered wearable electronics.

Flexible Carbon Nanotube-Epitaxially Grown Nanocrystals for Micro-Thermoelectric Modules

Flexible thermoelectric materials have attracted increasing interest because of their potential use in thermal energy harvesting and high-spatial-resolution thermal management. However, a high-performance flexible micro-thermoelectric device (TED) compatible with the microelectronics fabrication process has not yet been developed. Here a universal epitaxial growth strategy is reported guided by 1D van der Waals-coupling, to fabricate freestanding and flexible hybrids comprised of single-wall carbon nanotubes and ordered (Bi,Sb)2 Te3 nanocrystals. High power factors ranging from ≈1680 to ≈1020 µW m-1 K-2 in the temperature range of 300-480 K, combined with a low thermal conductivity yield a high average figure of merit of ≈0.81. The fabricated flexible micro-TED module consisting of two p-n couples of freestanding thermoelectric hybrids has an unprecedented open circuit voltage of ≈22.7 mV and a power density of ≈0.36 W cm-2 under ≈30 K temperature difference, and a net cooling temperature of ≈22.4 K and a heat absorption density of ≈92.5 W cm-2 .

Staggered-layer-boosted flexible Bi2Te3 films with high thermoelectric performance

Room-temperature bismuth telluride (Bi2Te3) thermoelectrics are promising candidates for low-grade heat harvesting. However, the brittleness and inflexibility of Bi2Te3 are far reaching and bring about lifelong drawbacks. Here we demonstrate good pliability over 1,000 bending cycles and high power factors of 4.2 (p type) and 4.6 (n type) mW m-1 K-2 in Bi2Te3-based films that were exfoliated from corresponding single crystals. This unprecedented bendability was ascribed to the in situ observed staggered-layer structure that was spontaneously formed during the fabrication to promote stress propagation whilst maintaining good electrical conductivity. Unexpectedly, the donor-like staggered layer rarely affected the carrier transport of the films, thus maintaining its superior thermoelectric performance. Our flexible generator showed a high normalized power density of 321 W m-2 with a temperature difference of 60 K. These high performances in supple thermoelectric films not only offer useful paradigms for wearable electronics, but also provide key insights into structure-property manipulation in inorganic semiconductors.

Nanoengineering Approach toward High Power Factor Ag2Se/Se Composite Films for Flexible Thermoelectric Generators

Herein, a flexible Ag₂Se/Se composite film with a high power factor has been fabricated on a nylon membrane. The film has a high density and contains well-crystallized Ag₂Se grains and embedded Se nanoinclusions, which exhibits not only excellent flexibility but also a comparably large room-temperature power factor and Seebeck coefficient of up to 2023 μW m^-1 K^-2 and -155 μV K^-1, respectively. The high Seebeck coefficient is ascribed to the energy-filtering effect as caused by the Se/Ag₂Se heterointerface. The assembled flexible thermoelectric generator (4-leg) exhibits a maximum output power of 1135 nW and a power density of up to 16.4 W m^-2 when the applied temperature difference is 30 K. This work offers a feasible method to design high-performance and low-cost flexible thermoelectric generators used for wearable electronics.

Scalable-produced 3D elastic thermoelectric network for body heat harvesting

Flexible thermoelectric generators can power wearable electronics by harvesting body heat. However, existing thermoelectric materials rarely realize high flexibility and output properties simultaneously. Here we present a facile, cost-effective, and scalable two-step impregnation method for fabricating a three-dimensional thermoelectric network with excellent elasticity and superior thermoelectric performance. The reticular construction endows this material with ultra-light weight (0.28 g cm^-3), ultra-low thermal conductivity (0.04 W m^-1 K^-1), moderate softness (0.03 MPa), and high elongation (>100%). The obtained network-based flexible thermoelectric generator achieves a pretty high output power of 4 μW cm^-2, even comparable to state-of-the-art bulk-based flexible thermoelectric generators.

Spin-Orbit-Coupling-Induced Topological Transition and Anomalously Strong Intervalley Scattering in Two-Dimensional Bismuth Allotropes with Enhanced Thermoelectric Performances

The convergence of multivalley bands is originally believed to be beneficial for thermoelectric performance by enhancing the charge conductivity while preserving the Seebeck coefficients, based on the assumption that electron interband or intervalley scattering effects are totally negligible. In this work, we demonstrate that β-Bi with a buckled honeycomb structure experiences a topological transition from a normal insulator to a Z₂ topological insulator induced by spin-orbit coupling, which subsequently increases the band degeneracy and is probably beneficial for enhancement of the thermoelectric power factor for holes. Therefore, strong intervalley scattering can be observed in both band-convergent β- and aw-Bi monolayers. Compared to β-Bi, aw-Bi with a puckered black-phosphorus-like structure possesses high carrier mobilities with 318 cm²/(V s) for electrons and 568 cm²/(V s) for holes at room temperature. We also unveil extraordinarily strong fourth phonon-phonon interactions in these bismuth monolayers, significantly reducing their lattice thermal conductivities at room temperature, which is generally anomalous in conventional semiconductors. Finally, a high thermoelectric figure of merit (zT) can be achieved in both bismuth monolayers, especially for aw-Bi with an n-type zT value of 2.2 at room temperature. Our results suggest that strong fourth phonon-phonon interactions are crucial to a high thermoelectric performance in these materials, and two-dimensional bismuth is probably a promising thermoelectric material due to its enhanced band convergence induced by the topological transition.

Sb2Te3 nanoparticle-containing single-walled carbon nanotube films coated with Sb2Te3 electrodeposited layers for thermoelectric applications

Single-walled carbon nanotubes (SWCNTs) are promising thermoelectric materials owing to their flexibility and excellent durability when exposed to heat and chemicals. Thus, they are expected to be used in power supplies for various sensors. However, their thermoelectric performances are inferior to those of inorganic thermoelectric materials. To improve the thermoelectric performance while maintaining the excellent characteristics of SWCNTs, a novel approach to form inorganic thermoelectric layers on the SWCNT bundle surfaces using electrodeposition is proposed. We synthesized Sb₂Te₃ nanoparticle-containing SWCNT films and coated them with electrodeposited Sb₂Te₃ layers. The Sb₂Te₃ nanoparticles were synthesized via a spontaneous redox reaction, which were then added to a SWCNT dispersion solution, and films were produced via vacuum filtration. At higher nanoparticle contents in the films, the Sb₂Te₃ electrodeposited layers completely covered the SWCNT bundles owing to the increase in the concentration of precursor ions near the SWCNT bundle surface, which in turn was the result of melted nanoparticles. The thermoelectric performance improved, and the maximum power factor at approximately 25 °C was 59.5 µW/(m K²), which was 4.7 times higher than that of the normal SWCNT film. These findings provide valuable insights for designing and fabricating high-performance flexible thermoelectric materials.

Positive and Negative Changes in the Electrical Conductance Related to Hybrid Filler Distribution Gradient in Composite Flexible Thermoelectric Films Subjected to Bending

P-type multiwalled carbon nanotubes (MWCNTs), as well as heterostructures fabricated by direct deposition of inorganic thermoelectric materials as antimony and bismuth chalcogenides on MWCNT networks are known as perspective materials for application in flexible thermoelectric polymer-based composites. In this work, the electrical response of three types of Sb₂Te₃-MWCNT heterostructures-based flexible films-free standing on a flexible substrate, encapsulated in polydimethylsiloxane (PDMS), and mixed in polyvinyl alcohol (PVA) is studied in comparison with the flexible films prepared by the same methods using bare MWCNTs. The electrical conductance of these films when each side of it was subsequently subjected to compressive and tensile stress during the film bending down to a 3 mm radius is investigated in relation to the distribution gradient of Sb₂Te₃-MWCNT heterostructures or bare MWCNTs within the film. It is found that all investigated Sb₂Te₃-MWCNT films exhibit a reversible increase in the conductance in response to the compressive stress of the film side with the highest filler concentration and its decrease in response to the tensile stress. In contrast, free-standing and encapsulated bare MWCNT networks with uniform distribution of nanotubes showed a decrease in the conductance irrelevant to the bending direction. In turn, the samples with the gradient distribution of the MWCNTs, prepared by mixing the MWCNTs with PVA, revealed behavior that is similar to the Sb₂Te₃-MWCNT heterostructures-based films. The analysis of the processes impacting the changes in the conductance of the Sb₂Te₃-MWCNT heterostructures and bare MWCNTs is performed. The proposed in this work bending method can be applied for the control of the uniformity of distribution of components in heterostructures and fillers in polymer-based composites.

Research Progress of Interfacial Design between Thermoelectric Materials and Electrode Materials

Intensive efforts have been conducted to realize the reliable interfacial joining of thermoelectric materials and electrode materials with low interfacial contact resistance, which is an essential step to make thermoelectric materials into thermoelectric devices for industrial application. In this review, the roles of structural integrity, interdiffusion, and contact resistance in long-term reliabilities of thermoelectric modules are outlined first. Then interfacial reactions of near-room-temperature Bi₂Te₃-based thermoelectric materials and various electrode materials are reviewed comprehensively. We also summarized the joining behavior of the mid-temperature PbTe-based thermoelectric materials and commonly used electrode materials. Subsequently, for other thermoelectric materials systems, i.e., SiGe, CoSb₃, and Mg₃Sb₂, previous attempts to join with some electrode materials are also recapitulated. Finally, some future prospects to further improve the joint reliability in thermoelectric device manufacturing are proposed. We believe that this review will provide guidance for preparing thermoelectric devices and optimizing thermoelectric device design.

Symmetry-Guaranteed High Carrier Mobility in Quasi-2D Thermoelectric Semiconductors

Quasi-2D semiconductors have garnered immense research interest for next-generation electronics and thermoelectrics due to their unique structural, mechanical, and transport properties. However, most quasi-2D semiconductors experimentally synthesized so far have relatively low carrier mobility, preventing the achievement of exceptional power output. To break through this obstacle, a route is proposed based on the crystal symmetry arguments to facilitate the charge transport of quasi-2D semiconductors, in which the horizontal mirror symmetry is found to vanish the electron-phonon coupling strength mediated by phonons with purely out-of-plane vibrational vectors. This is demonstrated in ZrBeSi-type quasi-2D systems, where the representative sample Ba_1.01 AgSb shows a high room-temperature hole mobility of 344 cm² V^-1 S^-1 , a record value among quasi-2D polycrystalline thermoelectrics. Accompanied by intrinsically low thermal conductivity, an excellent p-type zT of ≈1.3 is reached at 1012 K, which is the highest value in ZrBeSi-type compounds. This work uncovers the relation between electron-phonon coupling and crystal symmetry in quasi-2D systems, which broadens the horizon to develop high mobility semiconductors for electronic and energy conversion applications.

High thermoelectric performance of flexible nanocomposite films based on Bi2Te3 nanoplates and carbon nanotubes selected using ultracentrifugation

Thermoelectric generators with flexibility and high performance near 300 K have the potential to be employed in self-supporting power supplies for Internet of Things (IoT) devices. Bismuth telluride (Bi₂Te₃) exhibits high thermoelectric performance, and single-walled carbon nanotubes (SWCNTs) show excellent flexibility. Therefore, composites of Bi₂Te₃ and SWCNTs should exhibit an optimal structure and high performance. In this study, flexible nanocomposite films based on Bi₂Te₃ nanoplates and SWCNTs were prepared by drop casting on a flexible sheet, followed by thermal annealing. Bi₂Te₃ nanoplates were synthesized using the solvothermal method, and SWCNTs were synthesized using the super-growth method. To improve the thermoelectric properties of the SWCNTs, ultracentrifugation with a surfactant was performed to selectively obtain suitable SWCNTs. This process selects thin and long SWCNTs but does not consider the crystallinity, chirality distribution, and diameters. A film consisting of Bi₂Te₃ nanoplates and the thin and long SWCNTs exhibited high electrical conductivity, which was six times higher than that of a film with SWCNTs obtained without ultracentrifugation; this is because the SWCNTs uniformly connected the surrounding nanoplates. The power factor was 6.3 μW/(cm K²), revealing that this is one of the best-performing flexible nanocomposite films. The findings of this study can support the application of flexible nanocomposite films in thermoelectric generators to provide self-supporting power supplies for IoT devices.

Enhanced Thermoelectric Properties of Coated Vanadium Oxynitride Nanoparticles/PEDOT:PSS Hybrid Films

Thermoelectric (TE) materials transform thermal energy into electricity, which can play an important role for global sustainability. Conducting polymers are suitable for the preparation of flexible TE materials because of their low-cost, lightweight, flexible, and easily synthesized properties. Here, we fabricate organic-inorganic hybrids by combining vanadium oxynitride nanoparticles coated with nitrogen-doped carbon (NC@VNO) and poly(3,4-ethylenedioxy thiophene):poly(styrene sulfonate) (PEDOT:PSS). We find that the electrical conductivity, Seebeck coefficient, and power factor of the NC@VNO/PEDOT:PSS film can be enhanced up to 4158 S/cm, 45.8 μV/K, and 873 μW/mK2 at 380 K, respectively. The large enhancement of the power factor may be due to the facilitation of the interfacial charge transport tunnel between the NC@VNO nanoparticles and PEDOT:PSS. The improvement of the Seebeck coefficient may be due to the energy filter effect as induced by interfacial contact and internal electric field between the NC@VNO nanoparticles and PEDOT:PSS. Our measurement suggests that the high binding energy of pyrrolic-N enhances the Seebeck coefficient, and the high binding energy of oxide-N increases electrical conductivity.

Acid enhanced zipping effect to densify MWCNT packing for multifunctional MWCNT films with ultra-high electrical conductivity

The outstanding electrical and mechanical properties remain elusive on macroscopic carbon nanotube (CNT) films because of the difficult material process, which limits their wide practical applications. Herein, we report high-performance multifunctional MWCNT films that possess the specific electrical conductivity of metals as well as high strength. These MWCNT films were synthesized by a floating chemical vapor deposition method, purified at high temperature and treated with concentrated HCl, and then densified due to the developed chlorosulfonic acid-enhanced zipping effect. These large scalable films exhibit high electromagnetic interference shielding efficiency, high thermoelectric power factor, and high ampacity because of the densely packed crystalline structure of MWCNTs, which are promising for practical applications.

Physics-guided co-designing flexible thermoelectrics with techno-economic sustainability for low-grade heat harvesting

Flexible thermoelectric harvesting of omnipresent spatial thermodynamic energy, though promising in low-grade waste heat recovery (<100°C), is still far from industrialization because of its unequivocal cost-ineffectiveness caused by low thermoelectric efficiency and power-cost coupled device topology. Here, we demonstrate unconventional upcycling of low-grade heat via physics-guided rationalized flexible thermoelectrics, without increasing total heat input or tailoring material properties, into electricity with a power-cost ratio (W/US$) enhancement of 25.3% compared to conventional counterparts. The reduced material usage (44%) contributes to device power-cost "decoupling," leading to geometry-dependent optimal electrical matching for output maximization. This offers an energy consumption reduction (19.3%), electricity savings (0.24 kWh W^-1), and CO₂ emission reduction (0.17 kg W^-1) for large-scale industrial production, fundamentally reshaping the R&D route of flexible thermoelectrics for techno-economic sustainable heat harvesting. Our findings highlight a facile yet cost-effective strategy not only for low-grade heat harvesting but also for electronic co-design in heat management/recovery frontiers.

Proximity induced longitudinal and transverse thermoelectric response in graphene-ferromagnetic CrBr3vdW heterostructure

The integration of longitudinal and transverse thermoelectric (TE) fosters various new opportunities in tuning the charge transport behaviour and opens a platform for efficient thermopower devices. The presence of asymmetric electronic structure supposed to accomplish large thermopower and electronic figure of merit. Herein, we investigate magnetic proximity coupled longitudinal and transverse TE behaviour in heterostructure of monolayer semimetal, graphene and a monolayer ferromagnet, CrBr₃under the framework ofab initio-based calculations and employed constant relaxation time approximation (CRTA).The integrated density of states is elevated and asymmetric near Fermi energy region due to seamless proximity integration, depicting mixed character of graphene and CrBr₃. The asymmetric nature of electronic structure significantly affects the Seebeck coefficients (S) and electrical conductivity (σ/τ) of heterostructure. The consistent step-like conductance spectrum influences interfacial polarization due to agile proximity integration. The magnitude of Seebeck coefficient (S) is found to be 653µV K^-1near Fermi level. The heterostructure observes higher electrical conductivity and power factor in n-type region of the order of 10⁶S m^-1and 10²⁰cm^-3at room temperature. The dimensionless electronic figure of merit (zT_e) advocates the heterostructure system to be an ideal TE material. Alongside longitudinal TE, we also find the heterostructure system is sensitive to anomalous Nernst effect (ANE) (transverse TE) with oscillatory nature. The Seebeck and ANE shows high degree of tunability with applied external electric field. The synergistic existence of Seebeck and ANE due to proximity integration in van der Waals atomic crystal at room temperature will provide realistic approach to experimentally fabricate and develop real-time thermopower devices.

A polarization-sensitive photothermoelectric photodetector based on mixed-dimensional SWCNT-MoS2 heterostructures

Mixed-dimensional van der Waals (vdW) integration has been demonstrated to be effective for the modulation of the physical properties of homogeneous materials. Herein, we reported the enhancement of photothermal conversion and decrease of thermal conductivity in metallic single-walled carbon nanotube (SWCNT) films with the integration of chemical vapor deposition-grown monolayer MoS₂ films. The induced temperature gradient in SWCNT-MoS₂ hybrid films drives carrier diffusion to generate photocurrent via the photothermoelectric (PTE) effect, and a self-powered photodetector working in the visible band range from 405 to 785 nm was demonstrated. The maximum responsivity of the device increases by 6 times compared to that of the SWCNT counterpart. More importantly, the mixed-dimensional device exhibits polarization-dependent photogeneration, showing a large anisotropy ratio of 1.55. This work paves a way for developing high-performance, polarization-sensitive photodetectors by mixed-dimensional integration.

Advancement of Polyaniline/Carbon Nanotubes Based Thermoelectric Composites

Organic thermoelectric (TE) materials have been widely investigated due to their good stability, easy synthesis, and high electrical conductivity. Among them, polyaniline/carbon nanotubes (PANI/CNTs) composites have attracted significant attention for pursuing enhanced TE properties to meet the demands of commercial applications. In this review, we summarize recent advances in versatile PANI/CNTs composites in terms of the dispersion methods of CNTs (such as the addition of surfactants, mechanical grinding, and CNT functional group modification methods), fabrication engineering (physical blending and in-situ polymerization), post-treatments (solvent treatments to regulate the doping level and microstructure of PANI), and multi-components composites (incorporation of other components to enhance energy filtering effect and Seebeck coefficient), respectively. Various approaches are comprehensively discussed to illustrate the microstructure modulation and conduction mechanism within PANI/CNTs composites. Furthermore, we briefly give an outlook on the challenges of the PANI/CNTs composites for achieving high performance and hope to pave a way for future development of high-performance PANI/CNTs composites for sustainable energy utilization.

Manipulating Single-Walled Carbon Nanotube Arrays for Flexible Photothermoelectric Devices

Flexible photothermoelectric (PTE) devices possess great application prospects in the field of light energy and thermoelectric energy harvesting which are some of the cornerstones of modern green renewable energy power generation. However, the low efficiency of PTE materials and lack of suitable manufacturing processes remain an impediment to restrict its rapid development. Here, we designed a flexible PTE device by printing a highly integrated single-walled carbon nanotubes (SWCNTs) array at intervals that were surface-functionalized with poly(acrylic acid) and poly(ethylene imine) as p-n heterofilms. After the introduction of a mask to give a selective light illumination and taking advantage of the photothermal effect of SWCNTs, a remarkable temperature gradient along the printed SWCNTs and a considerable power density of 1.3 μW/cm² can be achieved. Meanwhile, both experimental data and COMSOL theoretical simulations were adopted to optimize the performance of our device, showing new opportunities for new generation flexible PTE devices.

Post-Electric Current Treatment Approaching High-Performance Flexible n-Type Bi2Te3 Thin Films

Inorganic n-type Bi2Te3 flexible thin film, as a promising near-room temperature thermoelectric material, has attracted extensive research interest and application potentials. In this work, to further improve the thermoelectric performance of flexible Bi2Te3 thin films, a post-electric current treatment is employed. It is found that increasing the electric current leads to increased carrier concentration and electric conductivity from 1874 S cm−1 to 2240 S cm−1. Consequently, a high power factor of ~10.70 μW cm−1 K−2 at room temperature can be achieved in the Bi2Te3 flexible thin films treated by the electric current of 0.5 A, which is competitive among flexible n-type Bi2Te3 thin films. Besides, the small change of relative resistance <10% before and after bending test demonstrates excellent bending resistance of as-prepared flexible Bi2Te3 films. A flexible device composed of 4 n-type legs generates an open circuit voltage of ~7.96 mV and an output power of 24.78 nW at a temperature difference of ~35 K. Our study indicates that post-electric current treatment is an effective method in boosting the electrical performance of flexible Bi2Te3 thin films.

Enhanced Thermoelectric Properties of Bi2 Te3 -Based Micro-Nano Fibers via Thermal Drawing and Interfacial Engineering

High-performance thermoelectric (TE) materials with great flexibility and stability are urgently needed to efficiently convert heat energy into electrical power. Recently, intrinsically crystalline, mechanically stable, and flexible inorganic TE fibers that show TE properties comparable to their bulk counterparts have been of interest to researchers. Despite remarkable progress in moving TE fibers toward room-temperature TE conversion, the figure-of-merit value (ZT) and bending stability still need enhancement. Herein, interfacial-engineering-enhanced TE properties of micro-nano polycrystalline TE fibers fabricated by thermally drawing Bi₂ Te₃ -based bulks in a glass-fiber template are reported. The interfacial engineering effect comes from generating stress-induced oriented nanocrystals to increase electrical conductivity and producing strain-distorted interfaces to decrease thermal conductivity. The 4 µm-diameter fibers achieve a 40% higher ZT (≈1.4 at 300 K) than their bulk counterparts and show a reversible bending radius of 50 µm, approaching the theoretical elastic limit. This fabrication strategy works for a wide range of inorganic TE materials and benefits the development of fiber-based micro-TE devices.

Semiconductors flex thermoelectric power

Ductile inorganic semiconductors can help enable self-powered wearable electronics.

Flexible thermoelectrics based on ductile semiconductors

Flexible thermoelectrics provide a different solution for developing portable and sustainable flexible power supplies. The discovery of silver sulfide-based ductile semiconductors has driven a shift in the potential for flexible thermoelectrics, but the lack of good p-type ductile thermoelectric materials has restricted the reality of fabricating conventional cross-plane π-shaped flexible devices. We report a series of high-performance p-type ductile thermoelectric materials based on the composition-performance phase diagram in AgCu(Se,S,Te) pseudoternary solid solutions, with high figure-of-merit values (0.45 at 300 kelvin and 0.68 at 340 kelvin) compared with other flexible thermoelectric materials. We further demonstrate thin and flexible π-shaped devices with a maximum normalized power density that reaches 30 μW cm^-2 K^-2. This output is promising for the use of flexible thermoelectrics in wearable electronics.

Engineering thermoelectric and mechanical properties by nanoporosity in calcium cobaltate films from reactions of Ca(OH)2/Co3O4 multilayers

Controlling nanoporosity to favorably alter multiple properties in layered crystalline inorganic thin films is a challenge. Here, we demonstrate that the thermoelectric and mechanical properties of Ca3Co4O9 films can be engineered through nanoporosity control by annealing multiple Ca(OH)2/Co3O4 reactant bilayers with characteristic bilayer thicknesses (b t ). Our results show that doubling b t , e.g., from 12 to 26 nm, more than triples the average pore size from ∼120 nm to ∼400 nm and increases the pore fraction from 3% to 17.1%. The higher porosity film exhibits not only a 50% higher electrical conductivity of σ ∼ 90 S cm-1 and a high Seebeck coefficient of α ∼ 135 μV K-1, but also a thermal conductivity as low as κ ∼ 0.87 W m-1 K-1. The nanoporous Ca3Co4O9 films exhibit greater mechanical compliance and resilience to bending than the bulk. These results indicate that annealing reactant multilayers with controlled thicknesses is an attractive way to engineer nanoporosity and realize mechanically flexible oxide-based thermoelectric materials.