Superfluorescence from lead halide perovskite quantum dot superlattices

Special-point approach for optical absorption coefficient calculations on two-dimensional self-assemblies of type-II perovskite quantum dots

All-inorganic perovskite quantum dots with the usual cubic shape have emerged as a successful and low-cost alternative to electronically functional nanomaterials motivating various fields of applications, including high-efficiency photovoltaics. Here, we present an efficient and almost analytic approach for optical absorption coefficient calculation on self-assembled perovskite quantum dot films with type-II band alignment. The approach takes advantage of the special point technique for integration over the two-dimensional Brillouin zone, which minimizes the computational cost. The set of special wave-vector points is generated using the Monkhorst and Pack method. The optical absorption spectrum for phenyl-C60-butyric acid methyl ester (PCBM)/CsPbI3quantum dot films is computed, in good agreement with the experiment assuming a homogeneous linewidth of 50 meV and considering a ten special-point set. We show that light absorption in these systems is a cooperative optoelectronic property resulting from the quantum-mechanical coupling between perovskite nanocubes, leading to extended system states. The generality of this approach makes it suitable for calculating the optical absorption coefficient in a broad class of perovskite quantum dot systems.

Deterministic positioning of few aqueous colloidal quantum dots

Emerging quantum technologies that critically require the integration of quantum emitters on photonic platforms are hindered by the control over their position, quantity, and scalability. Herein, we describe a facile strategy to deposit aqueous silica-coated quantum dots (QDs) in a template of polymethyl methacrylate (PMMA) nanoholes that leverages saturated ethanol vapor drop-casting and subsequent lift-off of the template. Ethanol vapor incorporation into water droplets during the drying process reduces the meniscus contact angle, which increases capillary forces and enhances particle confinement within the pinning contact region. Furthermore, induced Marangoni flow controls the particle transport dynamics inside the droplets, making large-scale deposition possible. Controlling the hole diameter of the template demonstrates changes in the number of QDs per hole, which is consistent with the Poissonian distribution with the best results of ∼40% single-particle yield from an ∼80% total site occupancy. This method employs a simple setup, eliminating the need for intricate optimization, yet offers the potential for deterministic patterning within complex photonic platforms.

Deterministic Synthesis of a Two-Dimensional MAPbI3 Nanosheet and Twisted Structure with Moiré Superlattice

The synthesis of extremely thin 2D halide perovskites and the exploration of their interlayer interactions have garnered significant attention in current research. A recent advancement we have made involves the development of a successful technique for generating ultrathin MAPbI3 nanosheets with controlled thickness and an exposed intrinsic surface. This innovative method relies on utilizing the Ruddlesden-Popper (RP) phase perovskite (BA2MAn-1PbnI3n+1) as a template. However, the precise reaction mechanism remains incompletely understood. In this work, we systematically examined the dynamic evolution of the phase conversion process, with a specific focus on the influence of inorganic slab (composed of [PbI6]4- octahedrons) numbers on regulating the thickness and quality of the resulting MAPbI3 nanosheets. Additionally, the atomic structure is directly visualized using the transmission electron microscopy (TEM) method, confirming its exceptional quality. To illustrate interfacial interactions in ultrathin structures, artificial moiré superlattices are constructed through a physical transfer approach, revealing multiple localized high-symmetry stacks within a distinctive square moiré pattern. These findings establish a novel framework for investigating the physics of interfacial interactions in ionic semiconducting crystals.

Extreme Electron-Photon Interaction in Disordered Perovskites

The interaction of light with solids can be dramatically enhanced owing to electron-photon momentum matching. This mechanism manifests when light scattering from nanometer-sized clusters including a specific case of self-assembled nanostructures that form a long-range translational order but local disorder (crystal-liquid duality). In this paper, a new strategy based on both cases for the light-matter-interaction enhancement in a direct bandgap semiconductor - lead halide perovskite CsPbBr3 - by using electric pulse-driven structural disorder, is addressed. The disordered state allows the generation of confined photons, and the formation of an electronic continuum of static/dynamic defect states across the forbidden gap (Urbach bridge). Both mechanisms underlie photon-momentum-enabled electronic Raman scattering (ERS) and single-photon anti-Stokes photoluminescence (PL) under sub-band pump. PL/ERS blinking is discussed to be associated with thermal fluctuations of cross-linked [PbBr6]4- octahedra. Time-delayed synchronization of PL/ERS blinking causes enhanced spontaneous emission at room temperature. These findings indicate the role of photon momentum in enhanced light-matter interactions in disordered and nanostructured solids.

Fate of Optical Excitons in FAPbI3 Nanocube Superlattices

Understanding the nature of the photoexcitation and ultrafast charge dynamics pathways in organic halide perovskite nanocubes and their aggregation into superlattices is key for potential applications as tunable light emitters, photon-harvesting materials, and light-amplification systems. In this work, we apply two-dimensional coherent electronic spectroscopy (2DES) to track in real time the formation of near-infrared optical excitons and their ultrafast relaxation in CH(NH2)2PbI3 nanocube superlattices. Our results unveil that the coherent ultrafast dynamics is limited by the combination of the inherent short exciton decay time (≃40 fs) and the dephasing due to the coupling with selective optical phonon modes at higher temperatures. On the picosecond time scale, we observe the progressive formation of long-lived localized trap states. The analysis of the temperature dependence of the excitonic intrinsic line width, as extracted by the antidiagonal components of the 2D spectra, unveils a dramatic change of the excitonic coherence time across the cubic to tetragonal structural transition. Our results offer a new way to control and enhance the ultrafast coherent dynamics of photocarrier generation in hybrid halide perovskite synthetic solids.

Assembly of Differently Sized Supercharged Protein Nanocages into Superlattices for Construction of Binary Nanoparticle-Protein Materials

This study focuses on the design and characterization of binary nanoparticle superlattices: Two differently sized, supercharged protein nanocages are used to create a matrix for nanoparticle arrangement. We have previously established the assembly of protein nanocages of the same size. Here, we present another approach for multicomponent biohybrid material synthesis by successfully assembling two differently sized supercharged protein nanocages with different symmetries. Typically, the ordered assembly of objects with nonmatching symmetry is challenging, but our electrostatic-based approach overcomes the symmetry mismatch by exploiting electrostatic interactions between oppositely charged cages. Moreover, our study showcases the use of nanoparticles as a contrast enhancer in an elegant way to gain insights into the structural details of crystalline biohybrid materials. The assembled materials were characterized with various methods, including transmission electron microscopy (TEM) and single-crystal small-angle X-ray diffraction (SC-SAXD). We employed cryo-plasma-focused ion beam milling (cryo-PFIB) to prepare lamellae for the investigation of nanoparticle sublattices via electron cryo-tomography. Importantly, we refined superlattice structure data obtained from single-crystal SAXD experiments, providing conclusive evidence of the final assembly type. Our findings highlight the versatility of protein nanocages for creating distinctive types of binary superlattices. Because the nanoparticles do not influence the type of assembly, protein cage matrices can combine various nanoparticles in the solid state. This study not only contributes to the expanding repertoire of nanoparticle assembly methods but also demonstrates the power of advanced characterization techniques in elucidating the structural intricacies of these biohybrid materials.

Recent Progress of Quantum Dots Light-Emitting Diodes: Materials, Device Structures, and Display Applications

Colloidal quantum dots (QDs), as a class of 0D semiconductor materials, have generated widespread interest due to their adjustable band gap, exceptional color purity, near-unity quantum yield, and solution-processability. With decades of dedicated research, the potential applications of quantum dots have garnered significant recognition in both the academic and industrial communities. Furthermore, the related quantum dot light-emitting diodes (QLEDs) stand out as one of the most promising contenders for the next-generation display technologies. Although QD-based color conversion films are applied to improve the color gamut of existing display technologies, the broader application of QLED devices remains in its nascent stages, facing many challenges on the path to commercialization. This review encapsulates the historical discovery and subsequent research advancements in QD materials and their synthesis methods. Additionally, the working mechanisms and architectural design of QLED prototype devices are discussed. Furthermore, the review surveys the latest advancements of QLED devices within the display industry. The narrative concludes with an examination of the challenges and perspectives of QLED technology in the foreseeable future.

Two-dimensional-lattice-confined single-molecule-like aggregates

Intermolecular distance largely determines the optoelectronic properties of organic matter. Conventional organic luminescent molecules are commonly used either as aggregates or as single molecules that are diluted in a foreigner matrix. They have garnered great research interest in recent decades for a variety of applications, including light-emitting diodes1,2, lasers3-5 and quantum technologies6,7, among others8-10. However, there is still a knowledge gap on how these molecules behave between the aggregation and dilution states. Here we report an unprecedented phase of molecular aggregate that forms in a two-dimensional hybrid perovskite superlattice with a near-equilibrium distance, which we refer to as a single-molecule-like aggregate (SMA). By implementing two-dimensional superlattices, the organic emitters are held in proximity, but, surprisingly, remain electronically isolated, thereby resulting in a near-unity photoluminescence quantum yield, akin to that of single molecules. Moreover, the emitters within the perovskite superlattices demonstrate strong alignment and dense packing resembling aggregates, allowing for the observation of robust directional emission, substantially enhanced radiative recombination and efficient lasing. Molecular dynamics simulations together with single-crystal structure analysis emphasize the critical role of the internal rotational and vibrational degrees of freedom of the molecules in the two-dimensional lattice for creating the exclusive SMA phase. This two-dimensional superlattice unifies the paradoxical properties of single molecules and aggregates, thus offering exciting possibilities for advanced spectroscopic and photonic applications.

Elucidating phonon dephasing mechanisms in layered perovskites with coherent Raman spectroscopies

Organic-inorganic hybrid perovskite quantum wells exhibit electronic structures with properties intermediate between those of inorganic semiconductors and molecular crystals. In these systems, periodic layers of organic spacer molecules occupy the interstitial spaces between perovskite sheets, thereby confining electronic excitations to two dimensions. Here, we investigate spectroscopic line broadening mechanisms for phonons coupled to excitons in lead-iodide layered perovskites with phenyl ethyl ammonium (PEA) and azobenzene ethyl ammonium (AzoEA) spacer cations. Using a modified Elliot line shape analysis for the absorbance and photoluminescence spectra, polaron binding energies of 11.2 and 17.5 meV are calculated for (PEA)2PbI4 and (AzoEA)2PbI4, respectively. To determine whether the polaron stabilization processes influence the dephasing mechanisms of coupled phonons, five-pulse coherent Raman spectroscopies are applied to the two systems under electronically resonant conditions. The prominence of inhomogeneous line broadening mechanisms detected in (AzoEA)2PbI4 suggests that thermal fluctuations involving the deformable organic phase broaden the distributions of phonon frequencies within the quantum wells. In addition, our data indicate that polaron stabilization primarily involves photoinduced reorganization of the organic phases for both systems, whereas the impulsively excited phonons represent less than 10% of the total polaron binding energy. The signal generation mechanisms associated with our fifth-order coherent Raman experiments are explored with a perturbative model in which cumulant expansions are used to account for time-coincident vibrational dephasing and polaron stabilization processes.

Precursor Chemistry of Lead Bromide Perovskite Nanocrystals

We investigate the early stages of cesium lead bromide perovskite formation through absorption spectroscopy of stopped-flow reactions, high-throughput mapping, and direct synthesis and titration of potential precursor species. Calorimetric and spectroscopic measurements of lead bromide complex titrations combined with theoretical calculations suggest that bromide complexes with higher coordination numbers than previously considered for nonpolar systems can better explain observed behaviors. Synthesis mapping of binary lead halides reveals multiple lead bromide species with absorption peaks higher than 300 nm, including a previously observed species with a peak at 313 nm and two species with peaks at 345 and 370 nm that also appear as reaction intermediates during the formation of lead bromide perovskites. Based on theoretical calculations of excitonic energies that match within 50 meV, we give a preliminary assignment of these species as two-dimensional magic-sized clusters with side lengths of 2, 3, and 4 unit cells. Kinetic measurements of the conversion of benzoyl bromide precursor are connected to stopped-flow measurements of product formation and demonstrate that the formation of complexes and magic-sized clusters (i.e., nucleation) is controlled by precursor decomposition, whereas the growth rate of 2D and 3D perovskites is significantly slower.

Unraveling the excitonics of light emission from metal-halide perovskite quantum dots

Metal halide semicondictor perovskites have been under intense investigation for their promise in light absorptive applications like photovoltaics. They have more recently experienced interest for their promise in light emissive applications. A key aspect of perovskites is their glassy, ionic lattice that exhibits dynamical disorder. One possible result of this dynamical disorder is their strong coupling between electronic and lattice degrees of freedom which may confer remarkable properties for light emission such as defect tolerance. How does the system, comprised of excitons, couple to the bath, comprised of lattice modes? How does this system-bath interaction give rise to novel light emissive properties and how do these properties give insight into the nature of these materials? We review recent work from this group in which time-resolved photoluminescence spectroscopy is used to reveal such insights. Based upon a fast time resolution of 3 ps, energy resolution, and temperature dependence, a wide variety of insights are gleaned. These insights include: lattice contributions to the emission linewidths, multiexciton formation, hot carrier cooling, excitonic fine structure, single dot superradiance, and a breakdown of the Condon approximation, all due to complex structural dynamics in these materials.

Predictive Modeling of Nanocrystal Orientation in Superlattices: Insights from Ligand Entropy

The self-assembly of nanocrystals (NCs) into close-packed, ordered superlattices (SLs) is of broad, engineering interest. The coherent orientation of polyhedral nanocrystals within NC SLs enhances electronic, magnetic, and vibrational coupling, leading to a variety of emergent phenomena. Here, we show that coherent orientation of polyhedral NCs in many SLs can be understood simply by considering its effect on the conformational entropy of surface ligands. We report the predicted nanocrystal orientations and entropic driving force to orient for a broad range of nanocrystal shapes and superlattice unit cells, and we show that ligand entropy is sufficient to reproduce a host of reported experimental and computational observations. We additionally use this framework to predict the expected distribution of interstitial species such as solvent or unbound ligands in an oriented NC SL. This work offers intuition for understanding the orientation of NCs in superlattices and a future framework for analyzing multinary structures.

Threshold temperature of superfluorescence generation in CuCl quantum dots under resonant excitation of excitons and resonant two-photon excitation of biexcitons

We studied the threshold temperature of superfluorescence (SF) generation with regard to biexcitons in CuCl quantum dots (QDs) under resonant two-photon excitation of biexcitons and resonant excitation of excitons to demonstrate the influence of initial population densities in the QDs on SF generation. As a result, the threshold temperature under the resonant excitation of excitons was higher than that under the two-photon excitation of biexcitons. This indicates that the high density of excited dots facilitates the rapid establishment of coherence among the dots, overcoming disadvantages of incomplete population inversion and formation process of biexcitons. We performed a theoretical calculation of the time profiles of the biexcitonic emission based on semiconductor luminescence equations. The experimentally obtained temperature dependence of the time profiles was qualitatively reproduced by calculating their dependence on the dephasing rate. In addition, we estimated the temperature dependence of the phase relaxation time of the biexcitons in the CuCl QDs by analyzing the temperature dependence of SF.

Coherent phenomena and dynamics of lead halide perovskite nanocrystals for quantum information technologies

Solution-processed colloidal nanocrystals of lead halide perovskites have been intensively investigated in recent years in the context of optoelectronic devices, during which time their quantum properties have also begun to attract attention. Their unmatched ease of synthetic tunability and unique structural, optical and electronic properties, in conjunction with the confinement of carriers in three dimensions, have motivated studies on observing and controlling coherent light-matter interaction in these materials for quantum information technologies. This Review outlines the recent efforts and achievements in this direction. Particularly notable examples are the observation of coherent single-photon emission, evidence for superfluorescence and the realization of room-temperature coherent spin manipulation for ensemble samples, which have not been achieved for prototypical colloidal CdSe nanocrystals that have been under investigation for decades. This Review aims to highlight these results, point out the challenges ahead towards realistic applications and bring together the efforts of multidisciplinary communities in this nascent field.

Ligand Equilibrium Influences Photoluminescence Blinking in CsPbBr3: A Change Point Analysis of Widefield Imaging Data

Photoluminescence intermittency remains one of the biggest challenges in realizing perovskite quantum dots (QDs) as scalable single photon emitters. We compare CsPbBr3 QDs capped with different ligands, lecithin, and a combination of oleic acid and oleylamine, to elucidate the role of surface chemistry on photoluminescence intermittency. We employ widefield photoluminescence microscopy to sample the blinking behavior of hundreds of QDs. Using change point analysis, we achieve the robust classification of blinking trajectories, and we analyze representative distributions from large numbers of QDs (Nlecithin = 1308, Noleic acid/oleylamine = 1317). We find that lecithin suppresses blinking in CsPbBr3 QDs compared with oleic acid/oleylamine. Under common experimental conditions, lecithin-capped QDs are 7.5 times more likely to be nonblinking and spend 2.5 times longer in their most emissive state, despite both QDs having nearly identical solution photoluminescence quantum yields. We measure photoluminescence as a function of dilution and show that the differences between lecithin and oleic acid/oleylamine capping emerge at low concentrations during preparation for single particle experiments. From experiment and first-principles calculations, we attribute the differences in lecithin and oleic acid/oleylamine performance to differences in their ligand binding equilibria. Consistent with our experimental data, density functional theory calculations suggest a stronger binding affinity of lecithin to the QD surface compared to oleic acid/oleylamine, implying a reduced likelihood of ligand desorption during dilution. These results suggest that using more tightly binding ligands is a necessity for surface passivation and, consequently, blinking reduction in perovskite QDs used for single particle and quantum light experiments.

DNA-mediated assembly of Au bipyramids into anisotropic light emitting kagome superlattices

Colloidal crystal engineering with DNA allows one to design diverse superlattices with tunable lattice symmetry, composition, and spacing. Most of these structures follow the complementary contact model, maximizing DNA hybridization on building blocks and producing relatively close-packed lattices. Here, low-symmetry kagome superlattices are assembled from DNA-modified gold bipyramids that can engage only in partial DNA surface matching. The bipyramid dimensions and DNA length can be engineered for two different superlattices with rhombohedral unit cells, including one composed of a periodic stacking of kagome lattices. Enabled by the partial facet alignment, the kagome lattices exhibit lattice distortion, bipyramid twisting, and planar chirality. When conjugated with Cy-5 dyes, the kagome lattices serve as cavities with high-density optical states and large Purcell factors along lateral directions, leading to strong dipole radiation along the z axis and facet-dependent light emission. Such complex optical properties make these materials attractive for lasers, displays, and quantum sensing constructs.

AuBr3 Induces CsPb(Br/I)3 QDs to Self-Assemble into Nanowires

Perovskite quantum dots can form various forms such as nanowires, nanorods, and nanosheets through self-assembly. Nanoscale self-assembly can be used to fabricate materials with excellent device properties. This study introduces AuBr3 into CsPb(Br/I)3 quantum dots, causing them to assemble into nanowires. The nanowires form because part of Au3+ is surface-doped to replace Pb2+, and the [PbX6]4- octahedral structure is distorted. The symmetry of the structural surface is broken, and a dipole-moment-induced field is generated, thus promoting self-assembly. Moreover, the presence of Au nanoparticles (NPs) causes a localized surface plasmon resonance and generates strong van der Waals forces that promote self-assembly. Finally, to test other applications of perovskite nanowires, the solution method is used to prepare films by compounding the sample solution and polystyrene (PS) for backlighted displays.

Thermal Activation of Anti-Stokes Photoluminescence in CsPbBr3 Perovskite Nanocrystals: The Role of Surface Polaron States

Optically driven cooling of a material, or optical refrigeration, is possible when optical up-conversion via anti-Stokes photoluminescence (ASPL) is achieved with near-unity quantum yield. The recent demonstration of optical cooling of CsPbBr3 perovskite nanocrystals (NCs) has provided a path forward in the development of semiconductor-based optical refrigeration strategies. However, the mechanism of ASPL in CsPbBr3 NCs is not yet settled, and the prospects for cooling technologies strongly depend on details of the mechanism. By analyzing the Arrhenius behavior of ASPL in CsPbBr3 NCs, we investigated the relationship between the average energy gained per photon during up conversion, ΔE, and the thermal activation energy, Ea. We find that Ea is systematically larger than ΔE, and that Ea increases for larger ΔE. We suggest that the additional energetic cost is due to a rearrangement of the crystal lattice as charge carriers pass from surface localized, structurally distinct sub-gap polaron states to the free exciton state during up-conversion. Our interpretation is further corroborated by quantifying the impact of ligand coverage on the NC surface. These findings help inform the development of CsPbBr3 NCs for applications in optical refrigeration.

Circularly Polarized Luminescence Without External Magnetic Fields from Individual CsPbBr3 Perovskite Quantum Dots

Lead halide perovskite quantum dots (QDs), the latest generation of the colloidal QD family, exhibit outstanding optical properties, which are now exploited as both classical and quantum light sources. Most of their rather exceptional properties are related to the peculiar exciton fine-structure of band-edge states, which can support unique bright triplet excitons. The degeneracy of the bright triplet excitons is lifted with energetic splitting in the order of millielectronvolts, which can be resolved by the photoluminescence (PL) measurements of single QDs at cryogenic temperatures. Each bright exciton fine-structure-state (FSS) exhibits a dominantly linear polarization, in line with several theoretical models based on the sole crystal field, exchange interaction, and shape anisotropy. Here, we show that in addition to a high degree of linear polarization, the individual exciton FSS can exhibit a non-negligible degree of circular polarization even without external magnetic fields by investigating the four Stokes parameters of the exciton fine-structure in individual CsPbBr3 QDs through Stokes polarimetric measurements. We observe a degree of circular polarization up to ∼38%, which could not be detected by using the conventional polarimetric technique. In addition, we found a consistent transition from left- to right-hand circular polarization within the fine-structure triplet manifold, which was observed in magnetic-field-dependent experiments. Our optical investigation provides deeper insights into the nature of the exciton fine structures and thereby drives the yet-incomplete understanding of the unique photophysical properties of this class of QDs for the benefit of future applications in chiral quantum optics.

Binding Site Programmable Self-Assembly of 3D Hierarchical DNA Origami Nanostructures

DNA nanotechnology has broad applications in biomedical drug delivery and programmable materials. Characterization of the self-assembly of DNA origami and quantum dots (QDs) is necessary for the development of new DNA-based nanostructures. We use computation and experiment to show that the self-assembly of 3D hierarchical nanostructures can be controlled by programming the binding site number and their positions on DNA origami. Using biotinylated pentagonal pyramid wireframe DNA origamis and streptavidin capped QDs, we demonstrate that DNA origami with 1 binding site at the outer vertex can assemble multimeric origamis with up to 6 DNA origamis on 1 QD, and DNA origami with 1 binding site at the inner center can only assemble monomeric and dimeric origamis. Meanwhile, the yield percentages of different multimeric origamis are controlled by the QD:DNA-origami stoichiometric mixing ratio. DNA origamis with 2 binding sites at the αγ positions (of the pentagon) make larger nanostructures than those with binding sites at the αβ positions. In general, increasing the number of binding sites leads to increases in the nanostructure size. At high DNA origami concentration, the QD number in each cluster becomes the limiting factor for the growth of nanostructures. We find that reducing the QD size can also affect the self-assembly because of the reduced access to the binding sites from more densely packed origamis.

Nanocrystal Assemblies: Current Advances and Open Problems

We explore the potential of nanocrystals (a term used equivalently to nanoparticles) as building blocks for nanomaterials, and the current advances and open challenges for fundamental science developments and applications. Nanocrystal assemblies are inherently multiscale, and the generation of revolutionary material properties requires a precise understanding of the relationship between structure and function, the former being determined by classical effects and the latter often by quantum effects. With an emphasis on theory and computation, we discuss challenges that hamper current assembly strategies and to what extent nanocrystal assemblies represent thermodynamic equilibrium or kinetically trapped metastable states. We also examine dynamic effects and optimization of assembly protocols. Finally, we discuss promising material functions and examples of their realization with nanocrystal assemblies.

Inhomogeneous Au2S for Photoacoustic Imaging and Photodynamic Tumor Therapy Based on Different Forms of Energy Dissipation

Nanomaterials with unique structures and components play a crucial role in nanomedicine. In this study, we discovered that the inhomogeneous Au2S constructed by cation exchange and acid etching could dissipate energy in different forms after absorbing multichromatic light, which could be used to achieve the integrated diagnosis and treatment of tumors, respectively. Folic acid modified Au2S ringed nanoparticles (FA-Au2S RNs) with an assembly-like structure were demonstrated to result in better PA imaging performance and generate more reactive oxygen species (O2·-, ·OH, and 1O2) than folic acid modified Au2S triangular nanoparticles (FA-Au2S TNs). Finite element analyses determined the reason for the high absorbance properties and synergistic enhancement of plasma resonance in the assembly-like structure of Au2S RNs. Both FA-Au2S nanostructures were modified with folic acid and injected into 4T1 tumor-bearing mice via the tail vein. The best PA imaging contrast was obtained under 700 nm laser illumination, and the most effective PDT antitumor activity was achieved under 1064 nm laser illumination. The PA average of the tumor in the FA-Au2S RN group was approximately 2 times higher than that of the FA-Au2S TN group at 24 h of injection. The PA imaging results of intratumorally injected FA-Au2S RNs proved that they were still able to show better PA signal enhancement at 24 h postinjection. Our study demonstrates that FA-Au2S nanomaterials with unique structures and special properties can be reliably produced using strictly controlled chemical synthesis. It further provides a strategy for the construction of highly sensitive PA imaging platforms and efficient PDT antitumor agents that exploit wavelength-dependent energy dissipation mechanisms.

Low-threshold cavity-enhanced superfluorescence in polyhedral quantum dot superparticles

Due to the unique and excellent optical performance and promising prospect for various photonics applications, cavity-enhanced superfluorescence (CESF) in perovskite quantum dot assembled superstructures has garnered wide attention. However, the stringent requirements and high threshold for achieving CESF limit its further development and application. The high threshold of CESF in quantum dot superstructures is mainly attributed to the low radiation recombination rate of the quantum dot and the unsatisfactory light field limiting the ability of the assembled superstructures originating from low controllability of self-assembly. Herein, we propose a strategy to reduce the threshold of CESF in quantum dot superstructure microcavities from two aspects: facet engineering optimization of quantum dot blocks and controllability improvement of the assembly method. We introduce dodecahedral quantum dots with lower nonradiative recombination, substituting frequently used cubic quantum dots as assembly blocks. Besides, we adopt the micro-emulsion droplet assembly method to obtain spherical perovskite quantum dot superparticles with high packing factors and orderly internal arrangements, which are more controllable and efficient than the conventional solvent-drying methods. Based on the dodecahedral quantum dot superparticles, we realized low-threshold CESF (Pth = 15.6 μJ cm-2). Our work provides a practical and scalable avenue for realizing low threshold CESF in quantum dot assembled superstructure systems.

Bright Innovations: Review of Next-Generation Advances in Scintillator Engineering

This review focuses on modern scintillators, the heart of ionizing radiation detection with applications in medical diagnostics, homeland security, research, and other areas. The conventional method to improve their characteristics, such as light output and timing properties, consists of improving in material composition and doping, etc., which are intrinsic to the material. On the contrary, we review recent advancements in cutting-edge approaches to shape scintillator characteristics via photonic and metamaterial engineering, which are extrinsic and introduce controlled inhomogeneity in the scintillator's surface or volume. The methods to be discussed include improved light out-coupling using photonic crystal (PhC) coating, dielectric architecture modification producing the Purcell effect, and meta-materials engineering based on energy sharing. These approaches help to break traditional bulk scintillators' limitations, e.g., to deal with poor light extraction efficiency from the material due to a typically large refractive index mismatch or improve timing performance compared to bulk materials. In the Outlook section, modern physical phenomena are discussed and suggested as the basis for the next generations of scintillation-based detectors and technology, followed by a brief discussion on cost-effective fabrication techniques that could be scalable.

Coherent electronic coupling in quantum dot solids induces cooperative enhancement of nonlinear optoelectronic responses

Synchronized dynamics of quantum dot (QD) ensembles are essential for generating ultrafast and giant optical responses beyond those of individual QDs. Increasing the strength of the direct electronic coupling between QDs is a key strategy for the realization of cooperative quantum phenomena. Here, we observe a quantum cooperative effect on nonlinear photocurrents caused by the coherent electronic coupling in semiconductor QD solids. We measure quantum interference signals cooperatively generated in QD solids. We control the inter-QD distance with atomic precision using bidentate ligands that strongly link the QDs. The harmonic quantum interference signals are strongly enhanced when shortening the molecular length of the ligand. Furthermore, we clarify that the coherence length of multiexcitons extends to neighbouring QDs. This finding is direct evidence that multiexciton coherent tunnelling assists the ultrafast exciton delocalization. Cooperative enhancement in QD solids may find application in advanced quantum optoelectronics.

Metal-Halide Perovskite Lasers: Cavity Formation and Emission Characteristics

Hybrid metal-halide perovskites (MHPs) have shown remarkable optoelectronic properties as well as facile and cost-effective processability. With the success of MHP solar cells and light-emitting diodes, MHPs have also exhibited great potential as gain media for on-chip lasers. However, to date, stable operation of optically pumped MHP lasers and electrically driven MHP lasers-an essential requirement for MHP laser's insertion into chip-scale photonic integrated circuits-is not yet demonstrated. The main obstacles include the instability of MHPs in the atmosphere, rudimentary MHP laser cavity patterning methods, and insufficient understanding of emission mechanisms in MHP materials and cavities. This review aims to provide a detailed overview of different strategies to improve the intrinsic properties of MHPs in the atmosphere and to establish an optimal MHP cavity patterning method. In addition, this review discusses different emission mechanisms in MHP materials and cavities and how to distinguish them.

Decoding the Pathway-Dependent Self-Assembly of Polymer-Grafted Nanoparticles by Ligand Crystallization

Functional metamaterials can be constructed by assembling nanoparticles (NPs) into well-ordered structures, which show fascinating properties at different length scales. Using polymer-grafted NPs (PGNPs) as a building block, flexible composite metamaterials can be obtained, of which the structure is significantly affected by the property of polymer ligands. Here, it is demonstrated that the crystallization of polymer ligands determines the assembly behavior of NPs and reveal a pathway-dependent self-assembly of PGNPs into different metastructures in solution. By changing the crystallization degree of polymer ligands, the arrangement structure of NPs can be tailored. When the polymer ligands highly crystallize, the PGNPs assemble into diamond-shaped platelets, in which the NPs arrange disorderedly. When the polymer ligands lowly crystallize, the PGNPs assemble into highly ordered 3D superlattices, in which the NPs pack into a body-centered-cubic structure. The structure transformation of PGNP assemblies can be achieved by thermal annealing to regulate the crystallization of polymer ligands. Interestingly, the diamond-shaped platelets remain "living" for seeded epitaxial growth of newly added crystalline species. This work demonstrates the effects of ligand crystallization on the crystallization of NP, providing new insights into the structure regulation of metamaterials.

Synthesis of Size-Adjustable CsPbBr3 Perovskite Quantum Dots for Potential Photoelectric Catalysis Applications

As a direct band gap semiconductor, perovskite has the advantages of high carrier mobility, long charge diffusion distance, high defect tolerance and low-cost solution preparation technology. Compared with traditional metal halide perovskites, which regulate energy band and luminescence by changing halogen, perovskite quantum dots (QDs) have a surface effect and quantum confinement effect. Based on the LaMer nucleation growth theory, we have synthesized CsPbBr3 QDs with high dimensional homogeneity by creating an environment rich in Br- ions based on the general thermal injection method. Moreover, the size of the quantum dots can be adjusted by simply changing the reaction temperature and the concentration of Br- ions in the system, and the blue emission of strongly confined pure CsPbBr3 perovskite is realized. Finally, optical and electrochemical tests suggested that the synthesized quantum dots have the potential to be used in the field of photocatalysis.

Conjugated Zwitterionic Oligomers as Ligands on Perovskite Nanocrystals: Hybrid Structures with Tunable Interparticle Spacing

Conventional ligands for CsPbBr3 perovskite nanocrystals (NCs), composed of polar, coordinating head groups (e.g., ammonium or zwitterionic) and aliphatic tails, are instrumental in stabilizing the NCs against sintering and aggregation. Nonetheless, the aliphatic (insulating) nature of these ligands represents drawbacks with respect to objectives in optoelectronics, and yet removing these ligands typically leads to a loss of colloidal stability. In this paper, we describe the preparation of CsPbBr3 NCs in the presence of discrete conjugated oligomers that were prepared by an iterative synthetic approach and capped at their chain ends with sulfobetaine zwitterions for perovskite coordination. Notably, these zwitterionic oligofluorenes are compatible with the hot injection and ligand exchange conditions used to prepare CsPbBr3 NCs, yielding stable NC dispersions with high photoluminescence quantum yields (PLQY, >90%) and spectral features representative of both the perovskite core and conjugated ligand shell. Controlling the chain length of these capping ligands effectively regulated inter-NC spacing and packing geometry when cast into solid films, with evidence derived from both transmission electron microscopy (TEM) and grazing incidence X-ray scattering measurements.

Oriented Assembly of Lead Halide Perovskite Nanocrystals

Cesium lead halide nanostructures have highly tunable optical and optoelectronic properties. Establishing precise control in forming perovskite single-crystal nanostructures is key to unlocking the full potential of these materials. However, studying the growth kinetics of colloidal cesium lead halides is challenging due to their sensitivity to light, electron beam, and environmental factors like humidity. In this study, in situ observations of CsPbBr3-particle dynamics were made possible through extremely low dose liquid cell transmission electron microscopy, showing that oriented attachment is the dominant pathway for the growth of single-crystal CsPbBr3 architectures from primary nanocubes. In addition, oriented assembly and fusion of ligand-stabilized cubic CsPbBr3 nanocrystals are promoted by electron beam irradiation or introduction of polar additives that both induce partial desorption of the original ligands and polarize the nanocube surfaces. These findings advance our understanding of cesium lead halide growth mechanisms, aiding the controlled synthesis of other perovskite nanostructures.

All-Perovskite Multicomponent Nanocrystal Superlattices

Nanocrystal superlattices (NC SLs) have long been sought as promising metamaterials, with nanoscale-engineered properties arising from collective and synergistic effects among the constituent building blocks. Lead halide perovskite (LHP) NCs come across as outstanding candidates for SL design, as they demonstrate collective light emission, known as superfluorescence, in single- and multicomponent SLs. Thus far, LHP NCs have only been assembled in single-component SLs or coassembled with dielectric NC building blocks acting solely as spacers between luminescent NCs. Here, we report the formation of multicomponent LHP NC-only SLs, i.e., using only CsPbBr3 NCs of different sizes as building blocks. The structural diversity of the obtained SLs encompasses the ABO6, ABO3, and NaCl structure types, all of which contain orientationally and positionally locked NCs. For the selected model system, the ABO6-type SL, we observed efficient NC coupling and Förster-like energy transfer from strongly confined 5.3 nm CsPbBr3 NCs to weakly confined 17.6 nm CsPbBr3 NCs, along with characteristic superfluorescence features at cryogenic temperatures. Spatiotemporal exciton dynamics measurements reveal that binary SLs exhibit enhanced exciton diffusivity compared to single-component NC assemblies across the entire temperature range (from 5 to 298 K). The observed coherent and incoherent NC coupling and controllable excitonic transport within the solid NC SLs hold promise for applications in quantum optoelectronic devices.

Multiscale Supercrystal Meta-atoms

Meta-atoms are the building blocks of metamaterials, which are employed to control both generation and propagation of light as well as provide novel functionalities of localization and directivity of electromagnetic radiation. In many cases, simple dielectric or metallic resonators are employed as meta-atoms to create different types of electromagnetic metamaterials. Here, we fabricate and study supercrystal meta-atoms composed of coupled perovskite quantum dots. We reveal that these multiscale structures exhibit specific emission properties, such as spectrum splitting and polaritonic effects. We believe that such multiscale supercrystal meta-atoms will provide novel functionalities in the design of many novel types of active metamaterials and metasurfaces.

Long-Range Hot-Carrier Transport in Topologically Connected HgTe Quantum Dots

The utilization of hot carriers as a means to surpass the Shockley-Queasier limit represents a promising strategy for advancing highly efficient photovoltaic devices. Quantum dots, owing to their discrete energy states and limited multi-phonon cooling process, are regarded as one of the most promising materials. However, in practical implementations, the presence of numerous defects and discontinuities in colloidal quantum dot (CQD) films significantly curtails the transport distance of hot carriers. In this study, the harnessing of excess energies from hot-carriers is successfully demonstrated and a world-record carrier diffusion length of 15 µm is observed for the first time in colloidal systems, surpassing existing hot-carrier materials by more than tenfold. The observed phenomenon is attributed to the specifically designed honeycomb-like topological structures in a HgTe CQD superlattice, with its long-range periodicity confirmed by High-Resolution Transmission Electron Microscopy(HR-TEM), Selected Area Electron Diffraction(SAED) patterns, and low-angle X-ray diffraction (XRD). In such a superlattice, nonlocal hot carrier transport is supported by three unique physical properties: the wavelength-independent responsivity, linear output characteristics and microsecond fast photoresponse. These findings underscore the potential of HgTe CQD superlattices as a feasible approach for efficient hot carrier collection, thereby paving the way for practical applications in highly sensitive photodetection and solar energy harvesting.

Persistent enhancement of exciton diffusivity in CsPbBr3 nanocrystal solids

In semiconductors, exciton or charge carrier diffusivity is typically described as an inherent material property. Here, we show that the transport of excitons among CsPbBr3 perovskite nanocrystals (NCs) depends markedly on how recently those NCs were occupied by a previous exciton. Using transient photoluminescence microscopy, we observe a striking dependence of the apparent exciton diffusivity on excitation laser power that does not arise from nonlinear exciton-exciton interactions or thermal heating. We interpret our observations with a model in which excitons cause NCs to transition to a long-lived metastable configuration that markedly increases exciton transport. The exciton diffusivity observed here (>0.15 square centimeters per second) is considerably higher than that observed in other NC systems, revealing unusually strong excitonic coupling between NCs. The finding of a persistent enhancement in excitonic coupling may help explain other photophysical behaviors observed in CsPbBr3 NCs, such as superfluorescence, and inform the design of optoelectronic devices.

Pseudomorphic amorphization of three-dimensional superlattices through morphological transformation of nanocrystal building blocks

Nanocrystal (NC) superlattices (SLs) have been widely studied as a new class of functional mesoscopic materials with collective physical properties. The arrangement of NCs in SLs governs the collective properties of SLs, and thus investigations of phenomena that can change the assembly of NC constituents are important. In this study, we investigated the dynamic evolution of NC arrangements in three-dimensional (3D) SLs, specifically the morphological transformation of NC constituents during the direct liquid-phase synthesis of 3D NC SLs. Electron microscopy and synchrotron-based in situ small angle X-ray scattering experiments revealed that the transformation of spherical Cu2S NCs in face-centred-cubic 3D NC SLs into anisotropic disk-shaped NCs collapsed the original ordered close-packed structure. The random crystallographic orientation of spherical Cu2S NCs in starting SLs also contributed to the complete disordering of the NC array via random-direction anisotropic growth of NCs. This work demonstrates that an understanding of the anisotropic growth kinetics of NCs in the post-synthesis modulation of NC SLs is important for tuning NC array structures.

Superfluorescence from Electron-Hole Plasma at Moderate Temperatures of 175 K

Superfluorescence, a cooperative coherent spontaneous emission, is of great importance to the understanding of many-body correlation in optical processes. Even though superfluorescence has been demonstrated in many diverse systems, it is hard to observe in electron-hole plasma (EHP) due to its rapid dephasing and hence needs strong magnetic fields or complex microcavities. Herein, we report the first experimental observation of superfluorescence from EHP up to a moderate temperature of 175 K without external stimuli in a coupled metal halide perovskite quantum dots film. The EHP exhibits macroscopic quantum coherence through spontaneous synchronization. The coherence of the excited state decays by superfluorescence, which is redshifted 40 meV from the spontaneous emission with a ∼1700 times faster decay rate and exhibits quadratic fluence dependence. Notably, the excited state population's delayed growth and abrupt decay, which are strongly influenced by the pump fluence and the Burnham-Chiao ringing, are the characteristics of the superfluorescence. Our findings will open up a new frontier for cooperative emission and light beam-based technologies.

Manipulating Coherent Exciton Dynamics in CsPbI3 Perovskite Quantum Dots Using Magnetic Field

Lead halide perovskite quantum dots (QDs) have recently emerged as a promising material platform for quantum information processing owing to their strong light-matter interaction and relatively long-lived optical and spin coherences. In particular, the coherence of the fine-structure bright excitons is sustainable up to room temperature and can be observed even at an ensemble level. Here modulation of the polarization of these excitons in CsPbI3 QDs and manipulation of their time-domain coherent dynamics using a longitudinal magnetic field are demonstrated. The manipulation is realized using femtosecond quantum beat spectroscopy performed with both circularly- and linearly-polarized pulses. The results are well captured by the density of matrix simulation and are picturized using a Bloch sphere. This study forms the basis for preparing arbitrary coherent superpositions of excitons in perovskite QDs for an array of quantum technologies under near-ambient conditions.

Single-photon superradiance in individual caesium lead halide quantum dots

The brightness of an emitter is ultimately described by Fermi's golden rule, with a radiative rate proportional to its oscillator strength times the local density of photonic states. As the oscillator strength is an intrinsic material property, the quest for ever brighter emission has relied on the local density of photonic states engineering, using dielectric or plasmonic resonators1,2. By contrast, a much less explored avenue is to boost the oscillator strength, and hence the emission rate, using a collective behaviour termed superradiance. Recently, it was proposed3 that the latter can be realized using the giant oscillator-strength transitions of a weakly confined exciton in a quantum well when its coherent motion extends over many unit cells. Here we demonstrate single-photon superradiance in perovskite quantum dots with a sub-100 picosecond radiative decay time, almost as short as the reported exciton coherence time4. The characteristic dependence of radiative rates on the size, composition and temperature of the quantum dot suggests the formation of giant transition dipoles, as confirmed by effective-mass calculations. The results aid in the development of ultrabright, coherent quantum light sources and attest that quantum effects, for example, single-photon emission, persist in nanoparticles ten times larger than the exciton Bohr radius.

Observation of transition from superfluorescence to polariton condensation in CsPbBr3 quantum dots film

The superfluorescence effect has received extensive attention due to the many-body physics of quantum correlation in dipole gas and the optical applications of ultrafast bright radiation field based on the cooperative quantum state. Here, we demonstrate not only to observe the superfluorescence effect but also to control the cooperative state of the excitons ensemble by externally applying a regulatory dimension of coupling light fields. A new quasi-particle called cooperative exciton-polariton is revealed in a light-matter hybrid structure of a perovskite quantum dot thin film spin-coated on a Distributed Bragg Reflector. Above the nonlinear threshold, polaritonic condensation occurs at a nonzero momentum state on the lower polariton branch owning to the vital role of the synchronized excitons. The phase transition from superfluorescence to polariton condensation exhibits typical signatures of a decrease of the linewidth, an increase of the macroscopic coherence as well as an accelerated radiation decay rate. These findings are promising for opening new potential applications for super-brightness and unconventional coherent light sources and could enable the exploitation of cooperative effects for quantum optics.

Colloidal quantum dot materials for next-generation near-infrared optoelectronics

Colloidal quantum dots (CQDs) are a promising class of materials for next-generation optoelectronic devices, such as displays, LEDs, lasers, photodetectors, and solar cells. CQDs can be obtained at low cost and in large quantities using wet chemistry. CQDs have also been produced using various materials, such as CdSe, InP, perovskites, PbS, PbSe, and InAs. Some of these CQD materials absorb and emit photons in the visible region, making them excellent candidates for displays and LEDs, while others interact with low-energy photons in the near-infrared (NIR) region and are intensively utilized in NIR lasers, NIR photodetectors, and solar cells. In this review, we have focused on NIR CQD materials and reviewed the development of CQD materials for solar cells, NIR lasers, and NIR photodetectors since the first set of reports on CQD materials in these particular applications.

Excitonic Quantum Coherence in Light Emission from CsPbBr3 Metal-Halide Perovskite Nanocrystals

The decay of excited states via radiative and nonradiative paths is well understood in molecules and bulk semiconductors but less so in nanocrystals. Here, we perform time-resolved photoluminescence (t-PL) experiments on CsPbBr3 metal-halide perovskite nanocrystals, with a time resolution of 3 ps, sufficient to observe the decay of both excitons and biexcitons as a function of temperature. The striking result is that the radiative rate constant of the single exciton increases at low temperatures with an exponential functional form, suggesting quantum coherent effects with dephasing at high temperatures. The opposing directions of the radiative and nonradiative decay rate constants enable enhanced brightening of PL from excitons to biexcitons due to quantum effects, promoting a faster approach to the quantum theoretical limits of light emission. Ab initio quantum dynamics simulations reproduce the experimental observations of radiation controlled by quantum spatial coherence enhanced at low temperatures.

Hot Excitons Cool in Metal Halide Perovskite Nanocrystals as Fast as CdSe Nanocrystals

The idea of phonon bottlenecks has long been pursued in nanoscale materials for their application in hot exciton devices, such as photovoltaics. Decades ago, it was shown that there is no quantum phonon bottleneck in strongly confined quantum dots due to their physics of quantum confinement. More recently, it was proposed that there are hot phonon bottlenecks in metal halide perovskites due to their physics. Recent work has called into question these bottlenecks in metal halide perovskites. Here, we compare hot exciton cooling in a range of sizes of CsPbBr3 nanocrystals from weakly to strongly confined. These results are compared to strongly confined CdSe quantum dots of two sizes and degrees of quantum confinement. CdSe is a model system as a ruler for measuring hot exciton cooling being fast, by virtue of its efficient Auger-assisted processes. By virtue of 3 ps time resolution, the hot exciton photoluminescence can now be directly observed, which is the most direct measure of the presence of hot excitons and their lifetimes. The hot exciton photoluminescence decays on nearly the same 2 ps time scale on both the weakly confined perovskite and the larger CdSe quantum dots, much faster than the 10 ps cooling predicted by transient absorption experiments. The smaller CdSe quantum dot has still faster cooling, as expected from quantum size effects. The quantum dots of perovskites show extremely fast hot exciton cooling, decaying faster than detection limits of <1 ps, even faster than the CdSe system, suggesting the efficiency of Auger processes in these metal halide perovskite nanocrystals and especially in their quantum dot form. These results across a range of sizes of nanocrystals reveal extremely fast hot exciton cooling at high exciton density, independent of composition, but dependent upon size. Hence these metal halide perovskite nanocrystals seem to cool heavily following quantum dot physics.

Direct synthesis of CsPbX3 perovskite nanocrystal assemblies

Inorganic CsPbX3 (X = Cl, Br, I) perovskite nanocrystals (NCs) possess many advantageous optoelectronic properties, making them an attractive candidate for light emitting diodes, lasers, or photodetector applications. Such perovskite NCs can form extended assemblies that further modify their bandgap and emission wavelength. In this article, a facile direct synthesis of CsPbX3 NC assemblies that are 1 μm in size and are composed of 10 nm-sized NC building blocks is reported. The direct synthesis of these assemblies with a conventional hot-injection method of the NCs is achieved through the judicious selection of the solvent, ligands, and reaction stoichiometry. Only under selective reaction conditions where the surface ligand environment is tuned to enhance the hydrophobic interactions between ligand chains of neighbouring NCs is self-assembly achieved. These assemblies possess narrow and red-shifted photoluminescence compared to their isolated NC counterparts, which further expands the colour gamut that can be rendered from inorganic perovskites. This is demonstrated through simple down-converting light emitters.

One-Dimensionally Arranged Quantum-Dot Superstructures Guided by a Supramolecular Polymer Template

Colloidal quantum dots (QDs) exhibit important photophysical properties, such as long-range energy diffusion, miniband formation, and collective photoluminescence, when aggregated into well-defined superstructures, such as three-dimensional (3D) and two-dimensional (2D) superlattices. However, the construction of one-dimensional (1D) QD superstructures, which have a simpler arrangement, is challenging; therefore, the photophysical properties of 1D-arranged QDs have not been studied previously. Herein, we report a versatile strategy to obtain 1D-arranged QDs using a supramolecular polymer (SP) template. The SP is composed of self-assembling cholesterol derivatives containing two amide groups for hydrogen bonding and a carboxyl group as an adhesion moiety on the QDs. Upon mixing the SP and dispersed QDs in low-polarity solvents, the QDs self-adhered to the SP and self-arranged into 1D superstructures through van der Waals interactions between the surface organic ligands of the QDs, as confirmed by transmission electron microscopy. Furthermore, we revealed efficient photoinduced fluorescence resonance energy transfer between the 1D-arranged QDs by an in-depth analysis of the emission spectra and decay curves.

Electron-hole asymmetric magnetotransport of graphene-colloidal quantum dot device

Interfacing graphene with other low-dimensional material has gained attentions recently due to its potential to stimulate new physics and device innovations for optoelectronic and electronic applications. Here, we exploit a solution-processed approach to introduce colloidal quantum dot (CQD) to the bilayer graphene device. The magnetotransport properties of the graphene device is drastically altered due to the presence of the CQD potential, leading to the observation of AB-like oscillation in the quantum Hall regime and screening of the intervalley scattering. The anomalous magnetotransport behavior is attributed to the coulombic scattering introduced by the CQDs and is shown to be highly asymmetric depending on the polarity of the transport carriers. These results prove the potential of such flexible method for engineering microscopic scattering process and performance of the graphene device that may lead to intriguing device application in such hybrid system.

Energy Funneling in a Noninteger Two-Dimensional Perovskite

Energy funneling is a phenomenon that has been exploited in optoelectronic devices based on low-dimensional materials to improve their performance. Here, we introduce a new class of two-dimensional semiconductor, characterized by multiple regions of varying thickness in a single confined nanostructure with homogeneous composition. This "noninteger 2D semiconductor" was prepared via the structural transformation of two-octahedron-layer-thick (n = 2) 2D cesium lead bromide perovskite nanosheets; it consisted of a central n = 2 region surrounded by edge-lying n = 3 regions, as imaged by electron microscopy. Thicker noninteger 2D CsPbBr3 nanostructures were obtained as well. These noninteger 2D perovskites formed a laterally coupled quantum well band alignment with virtually no strain at the interface and no dielectric barrier, across which unprecedented intramaterial funneling of the photoexcitation energy was observed from the thin to the thick regions using time-resolved absorption and photoluminescence spectroscopy.

Evidence for Exciton Crystals in a 2D Semiconductor Heterotrilayer

Two-dimensional (2D) transition metal dichalcogenides (TMDC) and their moiré interfaces have been demonstrated for correlated electron states, including Mott insulators and electron/hole crystals commensurate with moiré superlattices. Here we present spectroscopic evidence for ordered bosons─interlayer exciton crystals in a WSe2/MoSe2/WSe2 trilayer, where the enhanced Coulomb interactions over those in heterobilayers have been predicted to result in exciton ordering. Ordered interlayer excitons in the trilayer are characterized by negligible mobility and by sharper PL peaks persisting to an exciton density of nex ∼ 1012 cm-2, which is an order of magnitude higher than the corresponding limit in the heterobilayer. We present evidence for the predicted quadrupolar exciton crystal and its transitions to dipolar excitons either with increasing nex or by an applied electric field. These ordered interlayer excitons may serve as models for the exploration of quantum phase transitions and quantum coherent phenomena.

Enhancing Multiexcitonic Emission in Metal-Halide Perovskites by Quantum Confinement

Semiconductor metal halide perovskite nanocrystals have been under intense investigation for their promise in a variety of optoelectronic applications, which arises from their remarkable properties of defect tolerance and efficient light emission. Recently, quantum dot versions of perovskite nanocrystals have been available, enabling investigation of how quantum size effects control optical function and performance in these quantum dots (QD), past their well-known covalent II-VI analogues. We perform time-resolved photoluminescence (t-PL) experiments on CsPbBr3 perovskite nanocrystals spanning in diameter from 5.8 nm strongly confined quantum dots to 18 nm weakly confined quantum dots. Experiments are performed with sufficient time resolution of 3 ps to observe the interaction energies and recombination kinetics from excitons to multiexcitons. Comparing the same sized QD reveals that perovskite QD have a larger radiative rate constant for emission from X than CdSe QD due to a larger oscillator strength. The multiexciton (MX) regime reveals that perovskite QD emit brightly and with more focused bandwidth than equivalent sized CdSe QD enabling more spectrally pure brightness. The MX kinetics reveals that the perovskite QD maintain efficient radiative decay, effectively competing with Auger recombination. These experiments reveal that the strongly confined QD of perovskites can be efficient multiexcitonic emitters, such as in high brightness light emitting diodes, especially in the blue.

Tuning perovskite nanocrystal superlattices for superradiance in the presence of disorder

The cooperative emission of interacting nanocrystals is an exciting topic fueled by recent reports of superfluorescence and superradiance in assemblies of perovskite nanocubes. Several studies estimated that coherent coupling is localized to a small fraction of nanocrystals (10-7-10-3) within the assembly, raising questions about the origins of localization and ways to overcome it. In this work, we examine single-excitation superradiance by calculating radiative decays and the distribution of superradiant wave function in two-dimensional CsPbBr3 nanocube superlattices. The calculations reveal that the energy disorder caused by size distribution and large interparticle separations reduces radiative coupling and leads to the excitation localization, with the energy disorder being the dominant factor. The single-excitation model clearly predicts that, in the pursuit of cooperative effects, having identical nanocubes in the superlattice is more important than achieving a perfect spatial order. The monolayers of large CsPbBr3 nanocubes (LNC = 10-20 nm) are proposed as model systems for experimental tests of superradiance under conditions of non-negligible size dispersion, while small nanocubes (LNC = 5-10 nm) are preferred for realizing the Dicke state under ideal conditions.

Self-assembly of perovskite nanoplates in colloidal suspensions

In recent years, perovskite nanocrystal superlattices have been reported with collective optical phenomena, offering a promising platform for both fundamental science studies and device engineering. In this same avenue, superlattices of perovskite nanoplates can be easily prepared on different substrates, and they too present an ensemble optical response. However, the self-assembly and optical properties of these aggregates in solvents have not been reported to date. Here, we report on the conditions for this self-assembly to occur and show a simple strategy to induce the formation of these nanoplate stacks in suspension in different organic solvents. We combined wide- and small-angle X-ray scattering and scanning transmission electron microscopy to evaluate CsPbBr3 and CsPbI3 perovskite nanoplates with different thickness distributions. We observed the formation of these stacks by changing the concentration of nanoplates and the viscosity of the colloidal suspensions, without the need for antisolvent addition. We found that, in hexane, the concentration for the formation of the stacks is rather high and approximately 80 mg mL-1. In contrast, in decane, dodecane, and hexadecane, we observe a much easier self-assembly of the nanoplates, presenting a clear correlation between the degree of aggregation and viscosity. We, then, discuss the impact of the self-assembly of perovskite nanoplates on Förster resonant energy transfer. Our predictions suggest an energy transfer efficiency higher than 50% for all the donor-acceptor systems evaluated. In particular, we demonstrate how the aggregation of these particles in hexadecane induces FRET for CsPbBr3 nanowires. For the n = 2 nanowires (donor) to the n = 3 nanowires (acceptor), the FRET rate was found to be 4.1 ns-1, with an efficiency of 56%, in agreement with our own predictions.