Graphene oxide-dependent growth and self-aggregation into a hydrogel complex of exoelectrogenic bacteria

Preliminary evaluation of electricity recovery from palm oil mill effluent by anion exchange microbial fuel cell

This study assessed the viability of an anion-exchange microbial fuel cell (MFC) for extracting electricity from palm oil mill effluent (POME), a major pollutant in palm-oil producing regions due to increasing demand. The MFC incorporated a tubular membrane electrode assembly (MEA) with an air core, featuring a carbon-painted carbon-cloth cathode, an anion exchange membrane (AEM), and a nonwoven graphite fabric (NWGF) anode. An additional carbon brush (CB) anode was placed adjacent to the tubular MEA. The MFC operated under semi-batch conditions with POME replacement every 7 days. Results showed superior performance of the AEM, with the highest power density (Pmax) observed in POME-treated MFCs. Current and power density increased with CB addition; the best chemical oxygen demand (COD) removal efficiency reached 73 %, decreasing from 1249 to 332 mg/L with three CBs. The Pmax was 0.18 W/m-2(-|-) with 1000 mg/L COD and three CBs, dropping to 0.0031 W/m-2(-|-) without CB and at 410 mg/L COD. Anode resistance, calculated using organic matter supplementation, COD, and anode surface area, decreased with increased COD or surface area, improving electricity production. AEM and CB compatibility synergistically enhanced MFC performance, offering potential for POME wastewater treatment and energy recovery.

Scaling up of dual-chamber microbial electrochemical systems - An appraisal using systems design approach

Impetus to minimise the energy and carbon footprints of evolving wastewater resource recovery facilities has promoted the development of microbial electrochemical systems (MES) as an emerging energy-neutral and sustainable platform technology. Using separators in dual-chamber MES to isolate anodic and cathodic environments creates endless opportunities for its myriad applications. Nevertheless, the high internal resistance and the complex interdependencies among various system factors have challenged its scale-up. This critical review employed a systems approach to examine the complex interdependencies and practical issues surrounding the implementation and scalability of dual-chamber MES, where the anodic and cathodic reactions are mutually appraised to improve the overall system efficiency. The robustness and stability of anodic biofilms in large-volume MES is dependent on its inoculum source, antecedent history and enrichment strategies. The composition and anode-respiring activity of these biofilms are modulated by the anolyte composition, while their performance demands a delicate balance between the electrode size, macrostructure and the availability of substrates, buffers and nutrients when using real wastewater as anolyte. Additionally, the catholyte governed the reduction environment and associated energy consumption of MES with scalable electrocatalysts needed to enhance the sluggish reaction kinetics for energy-efficient resource recovery. A comprehensive assessment of the dual-chamber reactor configuration revealed that the tubular, spiral-wound, or plug-in modular MES configurations are suitable for pilot-scale, where it could be designed more effectively using efficient electrode macrostructure, suitable membranes and bespoke strategies for continuous operation to maximise their performance. It is anticipated that the critical and analytical understanding gained through this review will support the continuous development and scaling-up of dual-chamber MES for prospective energy-neutral treatment of wastewater and simultaneous circular management of highly relevant environmental resources.

Graphene-Based Engineered Living Materials

With the rise of engineered living materials (ELMs) as innovative, sustainable and smart systems for diverse engineering and biological applications, global interest in advancing ELMs is on the rise. Graphene-based nanostructures can serve as effective tools to fabricate ELMs. By using graphene-based materials as building units and microorganisms as the designers of the end materials, next-generation ELMs can be engineered with the structural properties of graphene-based materials and the inherent properties of the microorganisms. However, some challenges need to be addressed to fully take advantage of graphene-based nanostructures for the design of next-generation ELMs. This work covers the latest advances in the fabrication and application of graphene-based ELMs. Fabrication strategies of graphene-based ELMs are first categorized, followed by a systematic investigation of the advantages and disadvantages within each category. Next, the potential applications of graphene-based ELMs are covered. Moreover, the challenges associated with fabrication of next-generation graphene-based ELMs are identified and discussed. Based on a comprehensive overview of the literature, the primary challenge limiting the integration of graphene-based nanostructures in ELMs is nanotoxicity arising from synthetic and structural parameters. Finally, we present possible design principles to potentially address these challenges.

Graphene hydrogel improves S. putrefaciens' biological treatment of dye wastewater: Impacts of extracellular electron transfer and function of c-type cytochromes

Biocompatible materials and biocarriers have attracted great attention in biological wastewater treatment owing to their excellent performance in improving pollutant removal. Graphene-based material, a biocarrier candidate, with excellent adsorbability and conductivity was increasingly applied in anaerobic digestion due to its exceptional potential in the adsorption and electron transfer process. Nevertheless, the green approach for the formation of bio-graphene complexes and their mechanism in dye removal is limited. The aim of this study is to investigate and assess the performance of biological graphene hydrogel (BGH) formed by Shewanella putrefaciens CN32 on the removal of methyl orange (MO) and methylene blue (MB). The results showed that the formation of BGH is determined by the physicochemical characteristics of graphene oxide, including sheet size, oxidation degree, and interlayer distance. BGHs significantly increased the removal efficiency of dyes in comparison to non-graphene samples, with a 24-h removal rate of MO and MB reaching 92.9% and 91%, respectively. The synergetic mechanism of BGH on the enhanced removal rate of organic dye can be ascribed to GO's ability in accelerating extracellular electron transfer and stimulating biodegradation pathways relating to c-type cytochromes, including MtrA and MtrC. These findings provided an understanding of the relationship between graphene-based nanomaterials and Shewanella, which facilitated their future application in environmental biotechnology.

Soil organic matter and nutrient availability affect the applicability of low-carbon energy source in Dehalococcoides-augmented soil

Dehalococcoides is a functional microorganism that completely dechlorinates trichloroethene (TCE). Augmentation with pure Dehalococcoides is important for reducing environmental disturbances that accompany bioaugmentation. However, the applicability of Dehalococcoides-bioaugmentation to contaminated soils is unclear. In this study, seven low-carbon energy sources (methanol, formate, acetate, ethanol, lactate, citrate, and benzoate) were used as electron donors for Dehalococcides to evaluate its applicability in remediating TCE-contaminated soils. Soil microcosms supplemented with ethanol, formate, or lactate showed relatively high dechlorination activity within 111-180 days. The functional gene profiles predicted by PICRUSt2 from 16 S rRNA gene sequences were similar in the proportions of dehydrogenases, which initiate electron donor oxidation, in all soils and did not seem to reflect Dehalococcoides-bioaugmentation applicability. Soils with higher organic matter content (>3.2%; dry weight base) and protein concentration (>1.6 µg/mL) supported complete dechlorination. These results suggest that organic matter and nutrient availability mainly affect successful TCE dechlorination in Dehalococcoides-augmented soils. The study offers significant experimental support for comprehending the suitability of low-carbon energy sources in successful bioaugmentation, aiming to mitigate environmental disturbances associated with the process.

Living electrochemical biosensing: Engineered electroactive bacteria for biosensor development and the emerging trends

Bioelectrical interfaces made of living electroactive bacteria (EAB) provide a unique opportunity to bridge biotic and abiotic systems, enabling the reprogramming of electrochemical biosensing. To develop these biosensors, principles from synthetic biology and electrode materials are being combined to engineer EAB as dynamic and responsive transducers with emerging, programmable functionalities. This review discusses the bioengineering of EAB to design active sensing parts and electrically connective interfaces on electrodes, which can be applied to construct smart electrochemical biosensors. In detail, by revisiting the electron transfer mechanism of electroactive microorganisms, engineering strategies of EAB cells for biotargets recognition, sensing circuit construction, and electrical signal routing, engineered EAB have demonstrated impressive capabilities in designing active sensing elements and developing electrically conductive interfaces on electrodes. Thus, integration of engineered EAB into electrochemical biosensors presents a promising avenue for advancing bioelectronics research. These hybridized systems equipped with engineered EAB can promote the field of electrochemical biosensing, with applications in environmental monitoring, health monitoring, green manufacturing, and other analytical fields. Finally, this review considers the prospects and challenges of the development of EAB-based electrochemical biosensors, identifying potential future applications.

Reciprocal Interactions of Abiotic and Biotic Dechlorination of Chloroethenes in Soil

Chloroethenes (CEs) as common organic pollutants in soil could be attenuated via abiotic and biotic dechlorination. Nonetheless, information on the key catalyzing matter and their reciprocal interactions remains scarce. In this study, FeS was identified as a major catalyzing matter in soil for the abiotic dechlorination of CEs, and acetylene could be employed as an indicator of the FeS-mediated abiotic CE-dechlorination. Organohalide-respiring bacteria (OHRB)-mediated dechlorination enhanced abiotic CEs-to-acetylene potential by providing dichloroethenes (DCEs) and trichloroethene (TCE) since chlorination extent determined CEs-to-acetylene potential with an order of trans-DCE > cis-DCE > TCE > tetrachloroethene/PCE. In contrast, FeS was shown to inhibit OHRB-mediated dechlorination, inhibition of which could be alleviated by the addition of soil humic substances. Moreover, sulfate-reducing bacteria and fermenting microorganisms affected FeS-mediated abiotic dechlorination by re-generation of FeS and providing short chain fatty acids, respectively. A new scenario was proposed to elucidate major abiotic and biotic processes and their reciprocal interactions in determining the fate of CEs in soil. Our results may guide the sustainable management of CE-contaminated sites by providing insights into interactions of the abiotic and biotic dechlorination in soil.

Polyphasic Characterization of Geotalea uranireducens NIT-SL11 Newly Isolated from a Complex of Sewage Sludge and Microbially Reduced Graphene Oxide

Graphene oxide (GO), a chemically oxidized sheet of graphite, has been used as a conductive carbon carrier of microbes to boost various bioelectrochemical reactions. However, the types of microbes that can reduce GO have rarely been investigated. In this study, a strain of GO-reducing bacteria, named NIT-SL11, which was obtained from a hydrogel of microbially reduced GO and anaerobic sludge that converts sewage to electricity, was phylogenically identified as a novel strain of Geotalea uraniireducens. Considering the current lack of information on the electrogenic ability of the bacterium and its physicochemical and chemotaxonomic characteristics, the polyphasic characterization of the Geotalea uraniireducens strain NIT-SL11 was performed. NIT-SL11 utilized various organic acids, such as lactate, benzoate, and formate, as electron donors and exhibited respiration using GO, electrodes, fumarate, and malate. The strain contained C16:1ω7c and C16:0 as the major fatty acids and MK-8 and 9 as the major respiratory quinones. The complete genome of NIT-SL11 was 4.7 Mbp in size with a G+C content of 60.9%, and it encoded 80 putative c-type cytochromes and 23 type IV pili-related proteins. The possible extracellular electron transfer (EET) pathways of the strain were the porin-cytochrome (Pcc) EET pathway and type IV pili-based pathway.

Mechanistic insights into aggregation process of graphene oxide and bacterial cells in microbial reduction of ferrihydrite

Microbial reduction of ferrihydrite is prevalent in natural environments and plays an important role in reductive dissolution of Fe(III) minerals. With consistent release of anthropogenic graphene oxide (GO) into water bodies, new changes in the Fe(III)-reducing microorganisms/ferrihydrite binary system demand attention. Herein, we focused on the interaction of GO and bacterial cells in view of colloidal stability and interfacial forces, and on the consequences for microbial ferrihydrite reduction. The results showed that the addition of GO decreased the bioreduction efficiency of ferrihydrite down to 1/15 of the control. Meanwhile, the GO nanosheets were found not depositing on ferrihydrite but spontaneously aggregating with Shewanella spp., the representative dissimilatory Fe(III) reduction bacterial species. Using the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory and atomic force microscopy (AFM), the aggregation process can be interpreted in three steps according to the interaction energy calculation, namely, colloidal instability, reversible aggregation and irreversible aggregation. The motility of living cells seems the reason inducing the colloidal instability between GO and bacteria. While, the aggregation remains reversible even the secondary minimum achieved at the separation distance of 8.74-9.24 nm from XDLVO. When the separation distance <5.74-6.01 nm, the adhesion work predominates and causes irreversible aggregation, validated by AFM. Additionally, the probable ecological risks raised by this aggregation behavior for the imbalance of iron biogeochemical cycle were demonstrated.

Recent Implementations of Hydrogel-Based Microbial Electrochemical Technologies (METs) in Sensing Applications

Hydrogel materials have been used extensively in microbial electrochemical technology (MET) and sensor development due to their high biocompatibility and low toxicity. With an increasing demand for sensors across different sectors, it is crucial to understand the current state within the sectors of hydrogel METs and sensors. Surprisingly, a systematic review examining the application of hydrogel-based METs to sensor technologies has not yet been conducted. This review aimed to identify the current research progress surrounding the incorporation of hydrogels within METs and sensors development, with a specific focus on microbial fuel cells (MFCs) and microbial electrolysis cells (MECs). The manufacturing process/cost, operational performance, analysis accuracy and stability of typical hydrogel materials in METs and sensors were summarised and analysed. The current challenges facing the technology as well as potential direction for future research were also discussed. This review will substantially promote the understanding of hydrogel materials used in METs and benefit the development of electrochemical biosensors using hydrogel-based METs.

Formate: A promising electron donor to enhance trichloroethene-to-ethene dechlorination in Dehalococcoides-augmented groundwater ecosystems with minimal bacterial growth

Various substrates have been used to stimulate habitat microbes in chloroethene-contaminated groundwater, however, the specific efficiency and minimum growth of microbes have rarely been studied. This study investigated the effects of seven substrates on trichloroethene (TCE) dechlorination by augmentation of groundwater with Dehalococcoides mccartyi NIT01 and its contribution to the microbial community. Three out of eight test groups completed dechlorination of 1 mM TCE-to-ethene in varying durations; groundwater supplemented with formate (FOR) required 78 days, whereas the microcosms with lactate (LAC) and citrate (CIT) required approximately twice as long (143 days). The calculated efficiency of how much produced H₂ was used in dechlorination indicated a higher efficiency in FOR (36%) compared with LAC (1.9%) or CIT (2.9%). FOR showed lower microbial growth (3.4 × 10⁵ copies/mL) than LAC (1.5 × 10⁶) or CIT (4.4 × 10⁶), and maintained a higher Shannon diversity index (5.65) than LAC (4.97) and CIT (4.30). The rapid and higher H₂ transfer efficiency with lower bacterial growth by using formate was attributed to the slightly positive Gibbs free energy identified in H₂ production requiring a H₂-utilizer, lower carbon in the molecule, and adaptation to metabolic potential of the original groundwater microbiome. Formate is, therefore, a promising electron donor for rapid Dehalococcoides-augmented remediation with minimum bacterial growth. Sequential transferring of the FOR culture successfully maintained TCE-to-ethene dechlorination activity and enriched the members of genera Dehalococcoides (33%), Methanosphaerula (23%), Rectinema (13%), and Desulfitobacterium (5.6%). This suggests that formate is transferred to H₂ and acetate, and provided to Dehalococcoides.

Data-driven and validated dimensional analysis for rational scale-up of a dual-chamber microbial fuel cell system for water-energy nexus exploitation

Mathematical modelling of microbial fuel cells (MFC) facilitates their scale-up by maintaining dimensionless parameters across reactor volumes for consistent performance. This study developed data-driven correlations to predict areal power density for a batch-fed dual-chamber MFC using hybridised first-principle mechanistic model and Buckingham's Pi theorem. The established correlations were validated using experimentally-derived data for pre-enriched electroactive biofilm from mixed cultures. The biochemical model parameters are infilled with stoichiometric and thermodynamics estimations. Results showed that the correlations using logistic kinetics (Nash-Sutcliffe Efficiency, NSE = 0.59) outperformed Monod kinetics (NSE = 0.52) as the latter was not suitable for representing the first-order biochemical kinetics under limited substrate conditions. Sensitivity analysis on varying pH and bicarbonate concentration improved model predictions by ± 50%, though relative absolute error was ± 20% due to inherent error of estimated biochemical parameters. The application of hybridised approach for modelling MFC provides renewed perspectives for their rational design and scale-up applications.

Dehalococcoides mccartyi NIT01, a novel isolate, dechlorinates high concentrations of chloroethenes by expressing at least six different reductive dehalogenases

This study presents the isolation of a novel strain of Dehalococcoides mccartyi, NIT01, which can completely dechlorinate up to 4.0 mM of trichloroethene to ethene via 1,2-cis-dichroroethene and vinyl chloride within 25 days. Strain NIT01 dechlorinated chloroethenes (CEs) at a temperature range of 25-32 °C and pH range of 6.5-7.8. The activity of the strain was inhibited by salt at more than 1.3% and inactivated by 1 h exposure to 2.0% air or 0.5 ppm hypochlorous acid. The genome of NIT01 was highly similar to that of the Dehalococcoides strains DCMB5, GT, 11a5, CBDB1, and CG5, and all included identical 16S rRNA genes. Moreover, NIT01 had 19 rdhA genes including NIT01-rdhA7 and rdhA13, which are almost identical to vcrA and pceA that encode known dehalogenases for tetrachloroethene and vinyl chloride, respectively. We also extracted RdhAs from the membrane fraction of NIT01 using 0.5% n-dodecyl-β-d-maltoside and separated them by anion exchange chromatography to identify those involved in CE dechlorination. LC/MS identification of the LDS-PAGE bands and RdhA activities in the fractions indicated cellular expression of six RdhAs. NIT01-RdhA7 (VcrA) and NIT01-RdhA15 were highly detected and NIT01-RdhA6 was the third-most detected. Among these three RdhAs, NIT01-RdhA15 and NIT01-RdhA6 had no biochemically identified relatives and were suggested to be novel functional dehalogenases for CEs. The expression of multiple dehalogenases may support bacterial tolerance to high concentrations of CEs.

Conjugated Polyelectrolyte/Bacteria Living Composites in Carbon Paper for Biocurrent Generation

Successful practical implementation of bioelectrochemical systems requires developing affordable electrode structures that promote efficient electrical communication with microbes. Recent efforts have centered on immobilizing bacteria with organic semiconducting polymers on electrodes via electrochemical methods. This approach creates a fixed biocomposite that takes advantage of the increased electrode's electroactive surface area (EASA). Here, we demonstrate that a biocomposite comprising the water-soluble conjugated polyelectrolyte CPE-K and electrogenic Shewanella oneidensis MR-1 can self-assemble with carbon paper electrodes, thereby increasing its biocurrent extraction by ∼ 6-fold over control biofilms. A ∼ 1.5-fold increment in biocurrent extraction was obtained for the biocomposite on carbon paper relative to the biocurrent extracted from gold-coated counterparts. Electrochemical characterization revealed that the biocomposite stabilized with the carbon paper more quickly than atop flat gold electrodes. Cross-sectional images show that the biocomposite infiltrates inhomogeneously into the porous carbon structure. Despite an incomplete penetration, the biocomposite can take advantage of the large EASA of the electrode via long-range electron transport. These results show that previous success on gold electrode platforms can be improved when using more commercially viable and easily manipulated electrode materials. This article is protected by copyright. All rights reserved.

Electrostimulated bio-dechlorination of a PCB mixture (Aroclor 1260) in a marine-originated dechlorinating culture

Aroclor 1260, a commercial polychlorinated biphenyl (PCB) mixture, is highly recalcitrant to biotransformation. A negatively polarized cathode (-0.35 V vs. standard hydrogen electrode) was applied for the first time to a marine-origin PCB dechlorinating culture that substantially increased the microbial dechlorination rate of Aroclor 1260 (from 8.6 to 11.6 μM Cl^- d^-1); meta-chlorine removal was stimulated and higher proportions of tetra-CBs (43.2-46.6%), the predominant dechlorination products, were observed compared to the open circuit conditions (23.7-25.1%). The dechlorination rate was further enhanced (14.1 μM Cl^- d^-1) by amendment with humin as a solid-phase redox mediator. After the suspension culture was renewed using an anaerobic medium, dechlorination activity was effectively maintained solely by cathodic biofilms, where cyclic voltammetry results indicated their redox activity. Electric potential had a significant effect on microbial community structure in the cathodic biofilm, where a greater abundance of Dehalococcoides (2.59-3.02%), as potential dechlorinators, was observed compared to that in the suspension culture (0.41-0.55%). Moreover, Dehalococcoides adhering to the cathode showed a higher chlorine removal rate than in the suspension culture. These findings provide insights into the dechlorination mechanism of cathodic biofilms involving Dehalococcoides for PCB mixtures and extend the application prospects of bioremediation to PCB contamination in the natural environment.

De Novo Approach to Encapsulating Biocatalysts into Synthetic Matrixes: From Enzymes to Microbial Electrocatalysts

Biocatalysts hold great promise in chemical and electrochemical reactions. However, biocatalysts are prone to inhospitable physiochemical conditions. Encapsulating biocatalysts into a synthetic host matrix can improve their stability and activity, and broaden their operational conditions. In this Review, we summarize the emerging de novo approaches to encapsulating biocatalysts into synthetic matrixes. Here, de novo means that embedding of biocatalysts and construction of matrixes take place simultaneously. We discuss the advantages and limitations of the de novo approach. On the basis of the nature of the biocatalysts and the synthetic frameworks, we specifically focus on two aspects: (1) encapsulation of enzymes (in vitro) in metal-organic frameworks and (2) encapsulation of microbial electrocatalysts (in vivo) on the electrode. For both cases, we discuss how the encapsulation improves biocatalysts' performance (stability, viability, activity, and etc.). We also highlight the benefit of encapsulation in facilitating the transport of charge carriers in microbial electrocatalysis.

Isolation and Polyphasic Characterization of Desulfuromonas versatilis sp. Nov., an Electrogenic Bacteria Capable of Versatile Metabolism Isolated from a Graphene Oxide-Reducing Enrichment Culture

In this study, a novel electrogenic bacterium denoted as strain NIT-T3 of the genus Desulfuromonas was isolated from a graphene-oxide-reducing enrichment culture that was originally obtained from a mixture of seawater and coastal sand. Strain NIT-T3 utilized hydrogen and various organic acids as electron donors and exhibited respiration using electrodes, ferric iron, nitrate, and elemental sulfur. The strain contained C16:1ω7c, C16:0, and C15:0 as major fatty acids and MK-8, 9, and 7 as the major respiratory quinones. Strain NIT-T3 contained four 16S rRNA genes and showed 95.7% similarity to Desulfuromonasmichiganensis BB1T, the closest relative. The genome was 4.7 Mbp in size and encoded 76 putative c-type cytochromes, which included 6 unique c-type cytochromes (<40% identity) compared to those in the database. Based on the physiological and genetic uniqueness, and wide metabolic capability, strain NIT-T3 is proposed as a type strain of 'Desulfuromonas versatilis' sp. nov.

Comparative evaluation of fibrous artificial carbons and bamboo charcoal in terms of recovery of current from sewage wastewater

In this study, two fibrous carbon anodes (namely, pleated non-woven graphite (PNWG) and carbon brush (CB) made from artificial carbon) and bamboo charcoal (BC) were evaluated for current recovery from sewage wastewater. When these anodes were polarized at 0.2 V vs. Ag/AgCl in sewage wastewater, CB produced a maximum current of 2.9 A/m². This exceeded that produced by PNWG (1.5 A/m²) and BC (1.4 A/m²). The accumulative charge recovery achieved with CB was superior to those achieved with the other two (1.6- and 2.2-fold higher than that with PNWG and BC, respectively). During the cyclic voltammetry analysis, CB demonstrated the highest catalytic current with maximum potential in the range of -0.6 to 0.4 V vs. Ag/AgCl and the smallest anode resistance (0.20 Ωm²). Direct cell counting revealed that the fibrous anodes (CB and PNWG) attached most of the cells in the anodes (80%), whereas BC did not. In contrast, the proportion of Geobacter species, a representative electrogenic microorganism in the total bacteria, was observed to be similar among the three anodes (4.4-5.8%). The tubular microbial fuel cell (ø 5.0 cm) equipped with an air-chamber core wrapped with an anion exchange membrane (AEM) and the CB delivered a current of 1.8 A/m². This is higher than those reported in the existing literature for the same microbial fuel cell (MFC) configuration. This indicates that the alteration of the anode from planar to brush can contribute toward improving the current recovery through the air-cathode-AEM-MFC. The BC needs improvement to have more specific surface area, whereas it showed superiority in cost efficiency considering material and processing.

Biocatalyst physiology and interplay: a protagonist of MFC operation

Microbial fuel cells (MFC) have been foreseen as a sustainable renewable energy resource to meet future energy demand. In the past, several studies have been executed in both benchtop and pilot scale to produce electrical energy from wastewater. The key role players in this technology that leads to the operation are microbes, mainly bacteria. The dominant among them is termed as "exoelectrogens" that have the capability to produce and transport electron by utilizing waste source. The current review focuses on such electrogenic bacteria's involvement for enhanced power generation of MFC. The pathway of electron transfer in their cell along and its conduction to the extracellular environment of the MFC system are critically discussed. The interaction of the microbes in various MFC operational conditions, including the role of substrate and solid electron acceptors, i.e., anode, external resistance, temperature, and pH, was also discussed in depth along with biotechnological advancement and future research perspective.

Bacterial extracellular electron transfer: a powerful route to the green biosynthesis of inorganic nanomaterials for multifunctional applications

Synthesis of inorganic nanomaterials such as metal nanoparticles (MNPs) using various biological entities as smart nanofactories has emerged as one of the foremost scientific endeavors in recent years. The biosynthesis process is environmentally friendly, cost-effective and easy to be scaled up, and can also bring neat features to products such as high dispersity and biocompatibility. However, the biomanufacturing of inorganic nanomaterials is still at the trial-and-error stage due to the lack of understanding for underlying mechanism. Dissimilatory metal reduction bacteria, especially Shewanella and Geobacter species, possess peculiar extracellular electron transfer (EET) features, through which the bacteria can pump electrons out of their cells to drive extracellular reduction reactions, and have thus exhibited distinct advantages in controllable and tailorable fabrication of inorganic nanomaterials including MNPs and graphene. Our aim is to present a critical review of recent state-of-the-art advances in inorganic biosynthesis methodologies based on bacterial EET using Shewanella and Geobacter species as typical strains. We begin with a brief introduction about bacterial EET mechanism, followed by reviewing key examples from literatures that exemplify the powerful activities of EET-enabled biosynthesis routes towards the production of a series of inorganic nanomaterials and place a special emphasis on rationally tailoring the structures and properties of products through the fine control of EET pathways. The application prospects of biogenic nanomaterials are then highlighted in multiple fields of (bio-) energy conversion, remediation of organic pollutants and toxic metals, and biomedicine. A summary and outlook are given with discussion on challenges of bio-manufacturing with well-defined controllability.

Simultaneous Removal of Trivalent Arsenic and Nitrate Using Microbial Fuel Cells

A rectangular double chamber with trivalent arsenic as the electron donor of the biological anode was constructed by microbial fuel cells (MFC), and the feasibility of the MFC simultaneous degradation of trivalent arsenic and nitrate was studied. Experimental results show that the co-matrix-coupled MFC reactor oxidizes trivalent arsenic in an anode chamber and degrades nitrate in the cathode chamber. The removal rate of trivalent arsenic is about 63.35%, and the degradation rate of nitrate is about 55.95% during the complete and stable operation period. MFC can continuously output electric energy, and the maximum output voltage is 388 mV. We compared and analyzed the main functional microflora of biofilm microorganisms in an anode chamber. In the long-term arsenic-polluted environment, the activity of Acinetobacter, Pseudomonas bacteria with arsenic resistance, was improved. It is inferred that a fraction of trivalent arsenic was oxidized to pentavalent arsenic by electrode-attached microorganisms. While remaining trivalent, arsenic was taken up by the suspended bacterial biomass and converted into stable arsenide. The results of this study have theoretical reference value for the expansion of the MFC application scope.

Graphene: An Antibacterial Agent or a Promoter of Bacterial Proliferation?

Graphene materials (GMs) are being investigated for multiple microbiological applications because of their unique physicochemical characteristics including high electrical conductivity, large specific surface area, and robust mechanical strength. In the last decade, studies on the interaction of GMs with bacterial cells appear conflicting. On one side, GMs have been developed to promote the proliferation of electroactive bacteria on the surface of electrodes in bioelectrochemical systems or to accelerate interspecies electron transfer during anaerobic digestion. On the other side, GMs with antibacterial properties have been synthesized to prevent biofilm formation on membranes for water treatment, on medical equipment, and on tissue engineering scaffolds. In this review, we discuss the mechanisms and factors determining the positive or negative impact of GMs on bacteria. Furthermore, we examine the bacterial growth-promoting and antibacterial applications of GMs and debate their practicability.

Graphene: An Antibacterial Agent or a Promoter of Bacterial Proliferation?

Graphene materials (GMs) are being investigated for multiple microbiological applications because of their unique physicochemical characteristics including high electrical conductivity, large specific surface area, and robust mechanical strength. In the last decade, studies on the interaction of GMs with bacterial cells appear conflicting. On one side, GMs have been developed to promote the proliferation of electroactive bacteria on the surface of electrodes in bioelectrochemical systems or to accelerate interspecies electron transfer during anaerobic digestion. On the other side, GMs with antibacterial properties have been synthesized to prevent biofilm formation on membranes for water treatment, on medical equipment, and on tissue engineering scaffolds. In this review, we discuss the mechanisms and factors determining the positive or negative impact of GMs on bacteria. Furthermore, we examine the bacterial growth-promoting and antibacterial applications of GMs and debate their practicability.

Extracellular electron transfer leading to the biological mediated production of reduced graphene oxide

To explore a green, low-cost, and efficient strategy to synthesis reduced graphene oxide (RGO), the process and mechanism of the graphene oxide (GO) reduction by a model electrochemically active bacteria (EAB), Geobacter sulfurreducens PCA, were studied. In this work, up to 1.0 mg mL^-1 of GO was reduced by G. sulfurreducens within 0.5-8 days. I_D/I_G ratio in reduced product was similar to chemically RGO. After microbial reduction, the peak which corresponded to the reflection of graphene oxide (001) disappeared, while another peak considered as graphite spacing (002) appeared. The peak intensity of typical oxygen function groups, such as carboxyl C-O and >O (epoxide) groups, diminished in bacterially induced RGO comparing to initial GO. Besides, we observed the doping of nitrogen and phosphorus elements in bacterially induced RGO. In a good agreement with that, better electrochemical performance was noticed after GO reduction. As confirmed with differential pulse voltammetry (DPV) and cyclic voltammetry (CV) analysis, the maximum value of peak currents of bacterially induced RGO were significantly higher than those of GO. Our results showed the electron transfer at microbial cell/GO interface promoted the GO reduction, suggesting a broader application of EAB in biological mediated production of RGO.

Interaction between Biocompatible Graphene Oxide and Live Shewanella in the Self-Assembled Hydrogel: The Role of Physicochemical Properties

Understanding the interaction of graphene materials with bacterial cells is crucial for exploiting their environmental applications. Meanwhile, knowledge on the mechanism of graphene oxide (GO) action to bacteria is still incomplete. This study focused on the inter-relationship of biocompatible GO and the well-known dissimilatory metal-reducing bacteria Shewanella, in view of the biographene hydrogel (BGH), a self-assembly of GO and live bacteria. The results showed that, among various inter-related physicochemical properties of GO, the sheet area determined the bacterial survival and the gelation potential with the same Shewanella strain. For the biocompatible GO sheet above 0.30 μm², the larger the GO, the higher the speed of BGH assembling. Only 22 h was needed to obtain BGH using GO with an average area of 1.83 μm² (maximum in this study). The GO oxidation degree was found to be another critical factor affecting whether BGH formed or not, with a referential threshold of C/O > 1.75. Finally, surface force of GO was detected and correlated with the bacterial adhesion behavior for the first time, confirming that the large GO in the low oxidation state has high resultant force to attract bacteria. All these findings pave a promising way to develop a GO-bacteria complex like BGH to treat industrial wastewater in the future.

Living Bioelectrochemical Composites

Composites, in which two or more material elements are combined to provide properties unattainable by single components, have a historical record dating to ancient times. Few include a living microbial community as a key design element. A logical basis for enabling bioelectronic composites stems from the phenomenon that certain microorganisms transfer electrons to external surfaces, such as an electrode. A bioelectronic composite that allows cells to be addressed beyond the confines of an electrode surface can impact bioelectrochemical technologies, including microbial fuel cells for power production and bioelectrosynthesis platforms where microbes produce desired chemicals. It is shown that the conjugated polyelectrolyte CPE-K functions as a conductive matrix to electronically connect a three-dimensional network of Shewanella oneidensis MR-1 to a gold electrode, thereby increasing biocurrent ≈150-fold over control biofilms. These biocomposites spontaneously assemble from solution into an intricate arrangement of cells within a conductive polymer matrix. While increased biocurrent is due to more cells in communication with the electrode, the current extracted per cell is also enhanced, indicating efficient long-range electron transport. Further, the biocomposites show almost an order-of-magnitude lower charge transfer resistance than CPE-K alone, supporting the idea that the electroactive bacteria and the conjugated polyelectrolyte work synergistically toward an effective bioelectronic composite.

Effects of graphene oxide and reduced graphene oxide on acetoclastic, hydrogenotrophic and methylotrophic methanogenesis

This study describes the effects of graphene oxide (GO) and reduced graphene oxide (rGO) on the acetoclastic, hydrogenotrophic and methylotrophic pathways of methanogenesis by an anaerobic consortium. The results showed that GO negatively affected the hydrogenotrophic and acetoclastic pathways at a concentration of 300 mg/L, causing a decrease of ~ 38% on the maximum specific methanogenic activity (MMA) with respect to the controls lacking GO. However, the presence of rGO (300 mg/L) promoted an improvement of the MMA (> 45%) achieved with all substrates, except for the hydrogenotrophic pathway, which was relatively insensitive to rGO. The presence of either rGO or GO enhanced the methylotrophic pathway and resulted in an increase of the MMA of up to 55%. X-ray photoelectron spectroscopy (XPS) analysis revealed that GO underwent microbial reduction during the incubation period. Electrons derived from substrates oxidation were deviated from methanogenesis towards the reduction of GO, which may explain the MMA decreased observed in the presence of GO. Furthermore, XPS evidence indicated that the extent of GO reduction depended on the metabolic pathway triggered by a given substrate.

Direct Interspecies Electron Transfer Mediated by Graphene Oxide-Based Materials

Conductive materials are known to promote direct interspecies electron transfer (DIET) by electrically bridging microbial cells. Previous studies have suggested that supplementation of graphene oxide (GO) based materials, including GO, and reduced GO (rGO), to anaerobic microbial communities, can promote DIET. This promotion mechanism is thought to be involved in electron transfer via rGO or biologically formed rGO. However, concrete evidence that rGO directly promotes DIET is still lacking. Furthermore, the effects of the physicochemical properties of GO-based materials on DIET efficiency have not been elucidated. In the current work, we investigated whether chemically and biologically reduced GO compounds can promote DIET in a defined model coculture system, and also examined the effects of surface properties on DIET-promoting efficiency. Supplementation of GO to a defined DIET coculture composed of an ethanol-oxidizing electron producer Geobacter metallireducens and a methane-producing electron consumer Methanosarcina barkeri promoted methane production from ethanol. X-ray photoelectron spectroscopy revealed that GO was reduced to rGO during cultivation by G. metallireducens activity. The stoichiometry of methane production from ethanol and the isotope labeling experiments clearly showed that biologically reduced GO induced DIET-mediated syntrophic methanogenesis. We also assessed the DIET-promoting efficiency of chemically reduced GO and its derivatives, including hydrophilic amine-functionalized rGO (rGO-NH₂) and hydrophobic octadecylamine-functionalized rGO (rGO-ODA). While all tested rGO derivatives induced DIET, the rGO derivatives with higher hydrophilicity showed higher DIET-promoting efficiency. Optical microscope observation revealed that microbial cells, in particular, G. metallireducens, more quickly adhered to more hydrophilic GO-based materials. The superior ability to recruit microbial cells is a critical feature of the higher DIET-promoting efficiency of the hydrophilic materials. This study demonstrates that biologically and chemically reduced GO can promote DIET-mediated syntrophic methanogenesis. Our results also suggested that the surface hydrophilicity (i.e., affinity toward microbial cells) is one of the important determinants of the DIET-promoting efficiencies. These observations will provide useful guidance for the selection of conductive particles for the improvement of methanogenesis in anaerobic digesters.

Current recovery from sewage wastewater using electrochemically oxidized graphite felt

The oxidation of a carbon anode has been reported to enhance electricity recovery in a microbial fuel cell (MFC). This study investigates the applicability of electrochemically oxidized graphite felt (EOGF) as the anode for the recovery of electricity from sewage wastewater when polarized at 0.2 V during MFC operation. EOGFs were prepared by polarizing graphite felt (GF) at 2 V in 1% sulfuric acid or nitric acid. The nitric acid-treated EOGF inoculated with an sewage sludge produced a maximum current of 110 μA cm-3, which exceeds that produced by the original GF (91 μA cm-3) under electrochemical cultivation at 0.2 V vs. Ag/AgCl. This outcome is attributed to a decrease in charge-transfer resistance and an increase in the capacitance of the anode. In contrast, electrochemical oxidation did not affect the chemical oxygen demand (COD) removal rate or the microbial community structure of the anode. The MFC equipped with the EOGF delivered 340-560 mW m-3-MFC of electricity during operation in the drainage water channel of a primary sedimentation tank, which corresponds to 11-15 μA cm-3 of current density. The lower current produced in the MFC compared to that observed during electrochemical cultivation indicates that factors other than the anode material restrict current production in the MFC. Even with the small amount of generated electricity, when operated for more than three days, the MFC provides a positive net energy balance when integrated with post-aeration treatment.

Scaling up Microbial Fuel Cells for Treating Swine Wastewater

Conventional aerobic treatment of swine wastewater, which generally contains 4500–8200 mg L−1 of organic matter, is energy-consuming. The aim of this study was to assess the application of scaled-up microbial fuel cells (MFCs) with different capacities (i.e., 1.5 L, 12 L, and 100 L) for removing organic matter from swine wastewater. The MFCs were single-chambered, consisting of an anode of microbially reduced graphene oxide (rGO) and an air-cathode of platinum-coated carbon cloth. The MFCs were polarized via an external resistance of 3–10 Ω for 40 days for the 1.5 L-MFC and 120 days for the 12L- and 100 L-MFC. The MFCs were operated in continuous flow mode (hydraulic retention time: 3–5 days). The 100 L-MFC achieved an average chemical oxygen demand (COD) removal efficiency of 52%, which corresponded to a COD removal rate of 530 mg L−1 d−1. Moreover, the 100 L-MFC showed an average and maximum electricity generation of 0.6 and 2.2 Wh m−3, respectively. Our findings suggest that MFCs can effectively be used for swine wastewater treatment coupled with the simultaneous generation of electricity.

Bidirectional extracellular electron transfers of electrode-biofilm: Mechanism and application

The extracellular electron transfer (EET) between microorganisms and electrodes forms the basis for microbial electrochemical technology (MET), which recently have advanced as a flexible platform for applications in energy and environmental science. This review, for the first time, focuses on the electrode-biofilm capable of bidirectional EET, where the electrochemically active bacteria (EAB) can conduct both the outward EET (from EAB to electrodes) and the inward EET (from electrodes to EAB). Only few microorganisms are tested in pure culture with the capability of bidirectional EET, however, the mixed culture based bidirectional EET offers great prospects for biocathode enrichment, pollutant complete mineralization, biotemplated material development, pH stabilization, and bioelectronic device design. Future efforts are necessary to identify more EAB capable of the bidirectional EET, to balance the current density, to evaluate the effectiveness of polarity reversal for biocathode enrichment, and to boost the future research endeavors of such a novel function.

Enhanced sulfate and metal removal by reduced graphene oxide self-assembled Enterococcus avium sulfate-reducing bacteria particles

Graphene oxide (GO) was introduced to Enterococcus avium strain BY7 sulfate-reducing bacteria culture as a carrier, GO was partially reduced by SRB to reduced graphene oxide (rGO). The rGO could further self-assemble Enterococcus avium strain BY7 sulfate-reducing bacteria to form BY-rGO particles. Growth and sulfate reduction activity of strain BY7 was promoted by rGO, which probably due to the protective effect of rGO, and enhanced electron transfer by rGO as electron shuttle. Effects of pH and temperature variance on strain BY-rGO were remarkably weakened, growth and sulfate reduction were observed from pH 2.0 to 12.0, and from 10 to 45 °C, respectively. Metal toxicity to BY7 strain SRB was sharply decreased in BY-rGO particles and heavy metal removal was remarkably accelerated (up to 50%). The immobilization methods established in this study might open a new way for the application of SRBs, especially under extreme environmental conditions.

Enhance wastewater biological treatment through the bacteria induced graphene oxide hydrogel

The interaction between bacteria and graphene-family materials like pristine graphene, graphene oxide (GO) and reduced graphene oxide (rGO) is such an elusive issue that its implication in environmental biotechnology is unclear. Herein, two kinds of self-assembled bio-rGO-hydrogels (BGHs) were prepared by cultivating specific Shewanella sp. strains with GO solution for the first time. The microscopic examination by SEM, TEM and CLSM indicated a porous 3D structure of BGHs, in which live bacteria firmly anchored and extracellular polymeric substances (EPS) abundantly distributed. Spectra of XRD, FTIR, XPS and Raman further proved that GO was reduced to rGO by bacteria along with the gelation process, which suggests a potential green technique to produce graphene. Based on the characterization results, four mechanisms for the BGH formation were proposed, i.e., stacking, bridging, rolling and cross-linking of rGO sheets, through the synergistic effect of activities and EPS from special bacteria. More importantly, the BGHs obtained in this study were found able to achieve unique cleanup performance that the counterpart free bacteria could not fulfill, as exemplified in Congo red decolorization and Cr(VI) bioreduction. These findings therefore enlighten a prospective application of graphene materials for the biological treatment of wastewaters in the future.

Graphene oxide electrodeposited electrode enhances start-up and selective enrichment of exoelectrogens in bioelectrochemical systems

This study seeks to assess the impact that the anodic electrodeposition of graphene oxide (GO) has on the start-up process and on the development of microbial communities on the anode of BESs. The GO electrodeposited electrodes were characterised in abiotic conditions to verify the extent of the modification and were then transferred to a bioelectrochemical reactor. Results showed that the modified electrode allowed for a reduced start-up time compared to the control electrode. After three months, high throughput sequencing was performed, revealing that electrochemically reduced graphene oxide acts as a selective agent toward exoelectrogenic bacteria as Geobacter. Overall, this study shows that GO modified electrodes enhance biofilm build up in BES.

Functional Graphene Nanomaterials Based Architectures: Biointeractions, Fabrications, and Emerging Biological Applications

Functional graphene nanomaterials (FGNs) are fast emerging materials with extremely unique physical and chemical properties and physiological ability to interfere and/or interact with bioorganisms; as a result, FGNs present manifold possibilities for diverse biological applications. Beyond their use in drug/gene delivery, phototherapy, and bioimaging, recent studies have revealed that FGNs can significantly promote interfacial biointeractions, in particular, with proteins, mammalian cells/stem cells, and microbials. FGNs can adsorb and concentrate nutrition factors including proteins from physiological media. This accelerates the formation of extracellular matrix, which eventually promotes cell colonization by providing a more beneficial microenvironment for cell adhesion and growth. Furthermore, FGNs can also interact with cocultured cells by physical or chemical stimulation, which significantly mediate their cellular signaling and biological performance. In this review, we elucidate FGNs-bioorganism interactions and summarize recent advancements on designing FGN-based two-dimensional and three-dimensional architectures as multifunctional biological platforms. We have also discussed the representative biological applications regarding these FGN-based bioactive architectures. Furthermore, the future perspectives and emerging challenges will also be highlighted. Due to the lack of comprehensive reviews in this emerging field, this review may catch great interest and inspire many new opportunities across a broad range of disciplines.

Electricity Recovery from Municipal Sewage Wastewater Using a Hydrogel Complex Composed of Microbially Reduced Graphene Oxide and Sludge

Graphene oxide (GO) has recently been shown to be an excellent anode substrate for exoelectrogens. This study demonstrates the applicability of GO in recovering electricity from sewage wastewater. Anaerobic incubation of sludge with GO formed a hydrogel complex that embeds microbial cells via π-π stacking of microbially reduced GO. The rGO complex was electrically conductive (23 mS·cm⁻¹) and immediately produced electricity in sewage wastewater under polarization at +200 mV vs. Ag/AgCl. Higher and more stable production of electricity was observed with rGO complexes (179–310 μA·cm⁻³) than with graphite felt (GF; 79–95 μA·cm⁻³). Electrochemical analyses revealed that this finding was attributable to the greater capacitance and smaller internal resistance of the rGO complex. Microbial community analysis showed abundances of Geobacter species in both rGO and GF complexes, whereas more diverse candidate exoelectrogens in the Desulfarculaceae family and Geothrix genus were particularly prominent in the rGO complex.