Enhanced adsorptive removal of p-nitrophenol from water by aluminum metal-organic framework/reduced graphene oxide composite

Nitrophenol Reduction with Silver Oxide Nanostructures as a Sustainable Approach to Environmental Remediation

We propose silver oxide as a cost-effective and sustainable alternative to noble metals for the catalytic reduction of nitroaromatics. In the present investigation, we adopt a facile and green synthetic route for the synthesis of silver oxide nanostructures. The prepared nanostructures were found to crystallize in the cuprite phase and exhibit absorbance across the entire visible range of the electromagnetic spectrum. The catalytic potential of the silver oxide was evaluated by following the kinetics of nitrophenol reduction under ambient conditions and is observed to follow pseudo-first order kinetics with the apparent rate constantk a p p = 4 . 24 × 10 - 3 ${{k}_{app}=4.24\ \times {10}^{-3}}$ s-1 at minimum concentration of the catalyst. We attribute the observed catalytic activity to the freshly generated catalytic surface featuring a partially reduced form of silver oxide during reaction. The findings highlight the efficacy of silver oxide in mitigating the environmental pollution originating from the recalcitrant nitroarenes.

Sustainable synthesis of magnetic petroleum coke/nonanyl chitosan composite for efficient removal of o-nitrophenol

Worldwide industrialization has grown at a rapid pace, contaminating water resources, particularly with phenolic pollutants that pose a risk to aquatic systems and human health. The goal of this study is to create an inexpensive magnetic composite that can effectively remove nitrophenol (o-NP) using adsorptive means. In this instance, a nonanyl chitosan (N-Cs) derivative was synthesized and then combined with activated petroleum coke (AP-coke) and magnetic Fe3O4 to boost its adsorbability towards o-NP and to facilitate its separation. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffractometer (XRD), Vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and zeta potential were employed to characterize the magnetic composite. The experimental results indicated that the Fe3O4/AP-coke/N-Cs composite possesses a greater affinity toward o-NP with a maximal efficiency reached 88% compared to 22.8, 31.2, and 45.8% for Fe3O4, AP-coke and N-Cs, respectively. The equilibrium adsorption data coincided with the Langmuir, Freundlich, and Temkin isotherm models, with a maximum adsorption capacity of 291.55 mg/g at pH 6, whereas the pseudo second order kinetic model offered the best fit to the experimental data. Besides, the developed adsorbent preserved satisfactory adsorption characteristics after reuse for five successive cycles. The proposed adsorption mechanism involves the H-bonding, π-π interaction, hydrophobic interactions and electron donor-acceptor interactions. These findings hypothesize that the constructed magnetic composite could efficiently remove nitrophenols from polluted water with high performance and ease-separation.

Influences of Mg-activation on sugarcane bagasse biochar characteristics and its PNP removing potentials from contaminated water

Biochar as a substitute eco-friendly and low-cost adsorbent is introduced for removing p-nitrophenol (PNP) one of the most important chemical contaminant that recognized as the main metabolite in many pesticides and an intermediate compound in many industries. Physicochemical characteristics of sugarcane bagasse biochar (SCBB) and its Mg-activation (ASCBB) generated at 500 °C for 30 min were investigate. Batch kinetic experiment was conducted (200 mg L-1 PNP) to evaluate sorption efficiency of both tested biochars. To study the reaction behavior of PNP adsorption on ASCBB, solution pH and isotherm experiment of different concentrations and dosages were as investigated. The results show that ASCBB had a higher biochar yield, ash content, pH, molar ratios (H/C and O/C), surface area, pore volume, mean pore diameter, and specific and thick wall structure than SCBB. The efficiency of ASCBB to remove PNP was higher than SCBB which reached 51.98% in the first 1 min., and pH 7 achieved the optimum adsorption. Pseudo-second-order model examination exhibited well fitted to explain the adsorption results depending on R2 value (1.00). The adsorption isotherm results were well described by the Elovich and Freundlich models depending on the R2, qm and n values, which means the formation of a multilayer of PNP on the ASCBB surface through the chemisorption reaction. The calculated qm (144.93 mg g-1) of 1g L-1 was relatively close with experimental value (142.03 mg g-1). The PNP adsorption mechanism on both biochar types was electrostatic attraction, hydrogen bonding, and π-π stacking interactions, which were confirmed by studying the surface reactions before and after adsorption. Overall, the current study provided a successful waste biomass-derived biochar as a conducive alternative eco-sorbent to eliminate p-nitrophenol from wastewater.

Preparation of a Multifunctional and Multipurpose Chitosan/Cyclodextrin/MIL-68(Al) Foam Column and Examining Its Adsorption Properties for Anionic and Cationic Dyes and Sulfonamides

A multifunctional cylindrical hybrid foam column, referred to as the chitosan/cyclodextrin/MIL-68(Al) (CS/CD/MIL-68(Al)) foam column, was prepared for the first time. The prepared foam column could be used for the adsorption/removal of hydrophilic and hydrophobic contaminants by different forms. Here, it was placed in hydrophilic dye solutions to investigate the adsorption behavior of methylene blue and trypan blue. The adsorption process followed the pseudo-second-order kinetic model with R2 ranging from 0.9983 to 0.9998 for methylene blue and from 0.9993 to 1.0000 for trypan blue, and the adsorption process was consistent with the Langmuir isothermal model with R2 greater than 0.96. The RL values for methylene blue and trypan blue were 0.8871 and 0.5366, respectively, which were present between 0 and 1, indicating that the adsorption behaviors of the two dyes onto the CS/CD/MIL-68(Al) foam column were favorable. The maximum adsorption capacities (Qm) of methylene blue and trypan blue were 60.61 and 454.55 mg/g at 298 K, respectively. Also, the CS/CD/MIL-68(Al) foam column was spun into a syringe and used to adsorb trace hydrophobic sulfonamides from water in the form of filtration. The porous structure impeded the need for any external force and equipment, allowing the water sample to pass through the foam column smoothly. The conditions of the CS/CD/MIL-68(Al) foam column were optimized. The adsorption was carried out under the condition of pH = 4, the amount of the adsorbent was two foam columns, and no salt was added. It was found that the removal rate of the CS/CD/MIL-68(Al) foam column for six sulfonamides was 100%, and it could be reused at least five times. Therefore, this CS/CD/MIL-68(Al) foam column had a simple preparation method, offered a flexible and diverse form of use, was nonpolluting, biodegradable, and reusable, and could have a wider application in the field of environmental pollutant removal and adsorption.

Nanoporous carbons based on coordinate organic polymers as an efficient and eco-friendly nano-sorbent for adsorption of phenol from wastewater

The major part of water pollutants includes of organic such as phenolic pollutant, thus there are every hazardous to environment. Present work is a comparative onto surface chemistry and adsorptive characteristics of coordinate organic polymer (Cop-150) and nanoporous carbon (NPC) prepared using solvothermal method. New NPC was successfully synthesized to remove of phenol. FT-IR, XRD, XPS, SEM, TGA, and BET techniques have been used to characterization and confirm physicochemical variation during preparing Cop-150 and NPC. Box-Behnken response surface methodology (BBRSM) was used to optimize four important factors of the pH (2-10), contact time (1-40 min), temperature (25-60 °C), and initial concentration of phenol (5-50 mg L-1). To analyze the data obtained from the adsorption of phenol by synthesized adsorbents, four linear, 2FI, quadratic and cubic models were examined, which the quadratic model was recognized as the best model. To the NPC the equal adsorption capacity 500 mg g-1 is achieved at the initial concentration of phenol = 49.252 mg L-1, contact time = 15.738 min, temperature = 28.3 °C, and pH 7.042. On the other hand, the adsorption capacity for Cop-150 in pH 4.638, the contact time = 19.695 min, the temperature = 56.8 °C, and the initial concentration of phenol = 6.902 mg L-1 was equal to 50 mg g-1. The experimental data at different conditions were investigated by some famous kinetic and isotherm models, which among them, were corresponded to the pseudo-second-order kinetic model and the Langmuir isotherm. Moreover, based to result of thermodynamics to the both Cop-150 and NPC, the adsorption process is exothermic and spontaneous. According to results the Cop-150 and NPC could be used for up to four and five cycles without significantly reducing their performance, respectively.

Pine bark crosslinked to cyclodextrin for the adsorption of 2-nitrophenol from an aqueous solution

Adsorbents that are less expensive and more effective at removing organic micropollutants from wastewater have been developed through several approaches. Pine bark was treated with sodium hydroxide and then cross-linked to cyclodextrin using hexamethylene diisocyanate, in this study as an efficient adsorbent in the removal of 2-nitrophenol. FTIR, TGA and pHpzc analysis were used to characterize the biosorbent. The effects of pH, adsorbent mass, contact time and initial concentration on 2-nitrophenol removal was examined through batch adsorption studies. Pine bark crosslinked to cyclodextrin (PB-CD) surface functionalities was confirmed by FTIR analysis. It was discovered that solution pH, adsorbent mass, concentration and contact time all played a crucial role in the 2-nitrophenol uptake on PB-CD biosorbent and pine bark (PB) treated with sodium hydroxide. 2-Nitrophenol equilibrium was achieved with 0.05 g of adsorbents, with an initial concentration of 100–200 mg/dm3 at pH 5 after 60 min. The pseudo-second-order kinetic model and the Langmuir isotherm model significantly fitted the adsorption process. The Langmuir maximum capacities for PB and PB-CD were 47.36 mg/g and 77.82 mg/g, respectively. Overall, in the removal of 2-nitrophenol from an aqueous solution, PB-CD biosorbent is more cost-effective and efficient, in comparison with previously reported biosorbents in literature.

Controlling the Hydrogen Generation Reaction from Waste Water in Oil Fields Using an Ionic Liquid

Hydrogen production technologies are attracting widespread interest in energy technologies. The conventional methods for hydrogen production suffer from high cost, restricting their production everywhere. Here, we use waste formation water from a petroleum field and carbon steel materials to produce hydrogen. The most suitable conditions have been investigated to maximize the hydrogen yield. In addition, an ionic liquid (i.e., tributylmethylammonium methyl carbonate, BMAMC) has been used to control the hydrogen generation reaction. We reveal that the amount of hydrogen release rapidly increases with decreasing pH of the solution from 6.7 to 2.5. A further increase in temperature resulted in more amount of hydrogen release. Our study investigates the influence of chloride ions on hydrogen generation activity. The results revealed that ionic liquid BMAMC remarkably decreases the amount of hydrogen release with an efficiency of 92% at 5.08 × 10^-4 M. The addition of ionic liquid BMAMC into waste formation water increases the activation energy of the hydrogen generation reaction. The Langmuir model is the best isotherm describing the adsorption of BMAMC on carbon steel. Finally, to confirm the adsorption of the ionic liquid BMAMC, scanning electron microscopy and Fourier-transform infrared spectroscopy analysis were conducted.

Recent advances in application of metal-organic frameworks (MOFs) as adsorbent and catalyst in removal of persistent organic pollutants (POPs)

The presence of persistent organic pollutants (POPs) in the aquatic environment is causing widespread concern due to their bioaccumulation, toxicity, and possible environmental risk. These contaminants are produced daily in large quantities and released into water bodies. Traditional wastewater treatment plants are ineffective at degrading these pollutants. As a result, the development of long-term and effective POP removal techniques is critical. In water, adsorption removal and photocatalytic degradation of POPs have been identified as energy and cost-efficient solutions. Both technologies have received a lot of attention for their efforts to treat the world's wastewater. Photocatalytic removal of POPs is a promising, effective, and long-lasting method, while adsorption removal of persistent POPs represents a simple, practical method, particularly in decentralized systems and isolated areas. It is critical to develop new adsorbents/photocatalysts with the desired structure, tunable chemistry, and maximum adsorption sites for highly efficient removal of POPs. As a class of recently created multifunctional porous materials, Metal-organic frameworks (MOFs) offer tremendous prospects in adsorptive removal and photocatalytic degradation of POPs for water remediation. This review defines POPs and discusses current research on adsorptive and photocatalytic POP removal using emerging MOFs for each type of POPs.

Graphene-Based Metal-Organic Framework Hybrids for Applications in Catalysis, Environmental, and Energy Technologies

Current energy and environmental challenges demand the development and design of multifunctional porous materials with tunable properties for catalysis, water purification, and energy conversion and storage. Because of their amenability to de novo reticular chemistry, metal-organic frameworks (MOFs) have become key materials in this area. However, their usefulness is often limited by low chemical stability, conductivity and inappropriate pore sizes. Conductive two-dimensional (2D) materials with robust structural skeletons and/or functionalized surfaces can form stabilizing interactions with MOF components, enabling the fabrication of MOF nanocomposites with tunable pore characteristics. Graphene and its functional derivatives are the largest class of 2D materials and possess remarkable compositional versatility, structural diversity, and controllable surface chemistry. Here, we critically review current knowledge concerning the growth, structure, and properties of graphene derivatives, MOFs, and their graphene@MOF composites as well as the associated structure-property-performance relationships. Synthetic strategies for preparing graphene@MOF composites and tuning their properties are also comprehensively reviewed together with their applications in gas storage/separation, water purification, catalysis (organo-, electro-, and photocatalysis), and electrochemical energy storage and conversion. Current challenges in the development of graphene@MOF hybrids and their practical applications are addressed, revealing areas for future investigation. We hope that this review will inspire further exploration of new graphene@MOF hybrids for energy, electronic, biomedical, and photocatalysis applications as well as studies on previously unreported properties of known hybrids to reveal potential "diamonds in the rough".

Selective reduction of nitroarenes using Ru/C and CaH2

Herein, we report an efficient and highly selective method for the reduction of aromatic, heteroaromatic and halonitro compounds using the readily available and cost-effective Ru/C as a catalyst along with unconventional CaH₂ as a source of hydride. In most cases the corresponding anilines can be obtained by simple filtration without further purification. The use of 2-MeTHF and the simple operational work-up constitute a valid alternative to previous methodologies.

Study of the Effectiveness of Alumina and HDTMA/Alumina Composite in the Removal of Para-Nitrophenol and the Deactivation of Bacterial Effect of Listeria monocytogenes and Salmonella spp

Removal of para-nitrophenol (p-NP) from an aqueous solution was studied under various batch adsorption experiments, using alumina (Al2O3) and its composite hexadecyltrimethylammonium bromide (HDTMA+-Br−) as adsorbents. These were later characterized, before and after adsorption of p-NP, by thermal analysis (DSC-TG), X-ray diffraction (XRD), Fourier transform infrared (FTIR), and UV/Visible spectroscopies. The results show that HDTMA+/Al2O3 adsorbents have a greater affinity toward p-NP than Al2O3 alone. Linear and non-linear forms of kinetics and isotherms were used to analyze the experimental data obtained at different concentrations and temperatures. The results indicate that the pseudo-second order kinetic model provided the best fit to the experimental data for the adsorption of p-NP on both adsorbents, and that the intra-particle diffusion was not only the rate controlling step. Both the Langmuir and Redlich-Peterson (R-P) models were found to fit the sorption isotherm data well, but the Langmuir model was better. Physical adsorption of p-NP onto the adsorbents proved to be an endothermic and spontaneous process at high temperatures, which mainly involves a hydrogen bonding mechanism of interactions between p-NP and functional groups of adsorbents. The antibacterial activity of Al2O3, HDTMA+-Br− and HDTMA+/Al2O3 were evaluated against Listeria monocytogenes and Salmonella spp. strains using both disc diffusion and broth microdilution methods. The HDTMA+-Br− and HDTMA+/Al2O3 displayed a bacteriostatic effect against all tested strains of Listeria monocytogenes and Salmonella spp., while Al2O3 exhibited no bacterial effect against all bacterial strains tested.

Global qualitative and quantitative distribution of micropollutants in the deep sea

Micropollutants (MPs) include a wide range of biological disruptors that can be toxic to wildlife and humans at very low concentrations (<1 μg/L). These mainly anthropogenic pollutants have been widely detected in different areas of the planet, including the deep sea, and have impacts on marine life. Because of this potential toxicity, the global distribution, quantity, incidence, and potential impacts of deep-sea MPs were investigated in a systematic review of the literature. The results showed that MPs have reached different zones of the ocean and are more frequently reported in the Northern Hemisphere, where higher concentrations are found. MPs are also concentrated in depths up to 3000 m, where they are also more frequently studied, but also extend deeper than 10,000 m. Potentially toxic metals (PTMs), polychlorinated biphenyls (PCBs), dichlorodiphenyltrichloroethane (DDTs), organotins, and polycyclic aromatic hydrocarbons (PAHs) were identified as the most prevalent and widely distributed MPs at ≥200 m depth. PTMs are widely distributed in the deep sea in high concentrations; aluminum is the most prevalent up to 3000 m depth, followed by zinc and copper. PCBs, organotins, hexachlorocyclohexanes (HCHs), PAHs, and phenols were detected accumulated in both organisms and environmental samples above legislated thresholds or known toxicity levels. Our assessment indicated that the deep sea can be considered a sink for MPs.

Alleviative effects of magnetic Fe3O4 nanoparticles on the physiological toxicity of 3-nitrophenol to rice (Oryza sativa L.) seedlings

In the present study, we explored whether magnetic iron oxide nanoparticles (MNPs-Fe3O4) can be used to alleviate the toxicity of 3-nitrophenol (3-NP) to rice (Oryza sativa L.) seedlings grown under hydroponic conditions. The results showed that 3-NP from 7 to 560 μM decreased the growth, photochemical activity of the photosystem II (PS II), and chlorophyll content of the seedlings in a concentration-dependent manner. In the presence of 3-NP, 2,000 mg L−1 MNPs-Fe3O4 were added to the growth medium as the absorbents of 3-NP and then were separated with a magnet. The emergence of MNPs-Fe3O4 effectively alleviated the negative effects of 3-NP on rice seedlings. In addition, the long-term presence of MNPs-Fe3O4 (from 100 to 2,000 mg L−1) in the growth medium enhanced the growth, production of reactive oxygen species (ROS), activities of antioxidant enzymes, photochemical activity of PS II, and chlorophyll content of the rice seedlings. These results suggest that MNPs-Fe3O4 could be used as potential additives to relieve the physiological toxicity of 3-NP to rice seedlings.

Amine-amide functionalized graphene oxide sheets as bifunctional adsorbent for the removal of polar organic pollutants

Effective mitigation of polar organic impurities from industrial effluents is a global environmental challenge. Here, we describe the solvothermal synthesis of ammonia-functionalized graphene oxide (NH₃GO) sheets for adsorptive removal of diverse organic pollutants, such as cationic dye basic blue 41 (BB41), anionic dye methyl orange (MO), and ionic 4-nitrophenol (4-NP), in aqueous media. Structural analysis of NH₃GO suggest a potent role of surface acidic and basic binding sites in adsorption of targets through an interplay of dynamic experimental variables, e.g., contact time, pH, initial adsorbate concentration, adsorbent mass, and temperature. At an initial pollutant concentration of 20 mg/L, equilibrium adsorption capacities for BB41, MO, and 4-NP were estimated at 199.5, 64.0, and 54.1 mg/g, respectively, with corresponding partition coefficients of 4156, 79.4, and 14.3 L/g, respectively. Experimental data of all three organic pollutants are best fitted by the pseudo-second-order kinetic model. The adsorption isotherm of BB41 follows a multilayer adsorption pattern, while those of MO and 4-NP fit into a monolayer adsorption pattern. The endothermic and spontaneous nature of the adsorption processes has also been explored for the three targets on NH₃GO based on thermodynamic analysis. The prepared NH₃GO sheets appear to be a promising adsorbent for the removal of polar organic dyes and aromatics in the solution phase.

Highly efficient and simultaneous catalytic reduction of multiple toxic dyes and nitrophenols waste water using highly active bimetallic PdO-NiO nanocomposite

Azo dyes and nitrophenols have been widely used in the various industry which are highly toxic and affecting the photosynthetic cycle of aquatic organism. The industry disposals increase the accumulation of azo compounds in the environment. In the present study, we synthesized the low cost, PdO-doped NiO hetero-mixture via simple hydrothermal combined calcination process. The morphology results proved that, the spherical PdO nanoparticles are evenly doped with NiO nanoparticles. The band gap values of metal oxides NiO, PdO and PdO–NiO composite were found to be 4.05 eV, 3.84 eV and 4.24 eV, respectively. The high optical bandgap (Eg) value for composite suggests that the PdO interface and NiO interface are closely combined in the composite. The catalytic activity of the PdO–NiO was analyzed for the reduction of different toxic azo compounds namely, 4-nitrophenol (NP), 2,4-dinitrophenol (DNP), 2,4,6-trinitrophenol (TNP), methylene blue (MB), rhodamine B (RhB) and methyl orange (MO) separately and their mixture with the presence of a NaBH₄. For the first time, the large volume of the toxic azo compounds was reduced into non-toxic compounds with high reduction rate. The proposed PdO–NiO catalyst exhibit excellent rate constant 0.1667, 0.0997, 0.0686 min⁻¹ for NP, DNP and TNT and 0.099, 0.0416 and 0.0896 min⁻¹ for MB, RhB and MO dyes respectively which is higher rate constant than the previously reported catalysts. Mainly, PdO–NiO completes the reduction of mixture of azo compounds within 8 min. Further, PdO–NiO exhibit stable reduction rate of azo compounds over five cycles with no significant loss. Hence, the proposed low cost and high efficient PdO–NiO catalyst could be the promising catalyst for degradation of azo compounds.

Solar Light-Induced Methylene Blue Removal over TiO2/AC Composites and Photocatalytic Regeneration

TiO₂-containing photocatalysts, which combine TiO₂ with carbon-based materials, are promising materials for wastewater treatment due to synergistic photodegradation and adsorption phenomena. In this work, TiO₂/AC composites were produced by the in situ immobilization of TiO₂ nanoparticles over activated carbon (AC) derived from spent coffee grains, using different TiO₂/AC proportions. The TiO₂/AC composites were tested as adsorbents (dark) and as photocatalysts in a combined adsorption+photocatalytic process (solar irradiation) for methylene blue (MB) removal from ultrapure water, and from a secondary effluent (SecEf) of an urban wastewater treatment plant. All the materials were characterized by XRD (X-ray powder diffraction), N₂ adsorption–desorption isotherms at −196 °C, SEM (scanning electron microscopy), UV-Vis diffuse reflectance, FTIR (Fourier-transform infrared spectroscopy), TPD (temperature programmed desorption), XPS (X-ray photoelectron spectroscopy) and TGA (thermogravimetric analysis). The TiAC60 (60% C) composite presented the lowest band gap (1.84 eV), while, for TiAC29 (29% C), the value was close to that of bare TiO₂ (3.18 vs. 3.17 eV). Regardless of the material, the solar irradiation improved the percentage of MB discolouration when compared to adsorption in dark conditions. In the case of simultaneous adsorption+photocatalytic assays performed in ultrapure water, TiAC29 presented the fastest MB removal. Nevertheless, both TiAC29 and TiAC60 led to excellent MB removal percentages (96.1–98.1%). UV-induced photoregeneration was a promising strategy to recover the adsorption capacity of the materials, especially for TiAC60 and AC (>95%). When the assays were performed in SecEf, all the materials promoted discolouration percentages close to those obtained in ultrapure water. The bulk water parameters revealed that TiAC60 allowed the removal of a higher amount of MB, associated with the overall improvement of the SecEf quality.

Modern Carbon-Based Materials for Adsorptive Removal of Organic and Inorganic Pollutants from Water and Wastewater

Currently, a serious threat for living organisms and human life in particular, is water contamination with persistent organic and inorganic pollutants. To date, several techniques have been adopted to remove/treat organics and toxic contaminants. Adsorption is one of the most effective and economical methods for this purpose. Generally, porous materials are considered as appropriate adsorbents for water purification. Conventional adsorbents such as activated carbons have a limited possibility of surface modification (texture and functionality), and their adsorption capacity is difficult to control. Therefore, despite the significant progress achieved in the development of the systems for water remediation, there is still a need for novel adsorptive materials with tunable functional characteristics. This review addresses the new trends in the development of new adsorbent materials. Herein, modern carbon-based materials, such as graphene, oxidized carbon, carbon nanotubes, biomass-derived carbonaceous matrices-biochars as well as their composites with metal-organic frameworks (MOFs) and MOF-derived highly-ordered carbons are considered as advanced adsorbents for removal of hazardous organics from drinking water, process water, and leachate. The review is focused on the preparation and modification of these next-generation carbon-based adsorbents and analysis of their adsorption performance including possible adsorption mechanisms. Simultaneously, some weak points of modern carbon-based adsorbents are analyzed as well as the routes to conquer them. For instance, for removal of large quantities of pollutants, the combination of adsorption and other methods, like sedimentation may be recommended. A number of efficient strategies for further enhancing the adsorption performance of the carbon-based adsorbents, in particular, integrating approaches and further rational functionalization, including composing these adsorbents (of two or even three types) can be recommended. The cost reduction and efficient regeneration must also be in the focus of future research endeavors. The targeted optimization of the discussed carbon-based adsorbents associated with detailed studies of the adsorption process, especially, for multicomponent adsorbate solution, will pave a bright avenue for efficient water remediation.

Adsorption of 4-Nitrophenol on calcium alginate-multiwall carbon nanotube beads: Modeling, kinetics, equilibriums and reusability studies

In this study calcium alginate-multiwall carbon nanotube (CA/MWCNTs) was synthesized using (CA) calcium alginate and multiwall carbon nanotube (MWCNTs), and its efficiency in adsorption of 4-Nitrophenol (4-NP) in aqueous solution was studied. The structure and properties of the synthesized adsorbent were investigated using scanning electron microscope (SEM), thermal gravimetric analysis (TGA), Fourier transform infrared (FTIR), and X-ray diffraction (XRD). The experimental design was performed using Box-Behnken design (BBD) in which variables pH, CA/MWCNTs, and temperature were examined. The results of the effect of temperature on the removal efficiency of 4-NP showed that the adsorption efficiency decreases with increasing temperature. The results of nonlinear isotherm and kinetics models showed that Langmuir and pseudo-second-order models were more consistent than other models. The maximum adsorption capacity of 4-NP in this study by CA, MWCNTs, and CA/MWCNTs was 136, 168.4, and 58.8 mg/g, respectively, which indicates that the use of MWCNTs on CA could increase the adsorption capacity. The results of reuse of the synthesized adsorbent at 4-NP removal also showed that after 5 reuse of the adsorbent, the removal of 4-NP using CA/MWCNTs is reduced by about 10%, which shows that the synthesized adsorbent can be used several times to adsorb contaminants without significant reduction in the efficiency.

Cold Plasma Preparation of Pd/Graphene Catalyst for Reduction of p-Nitrophenol

Supported metal nanoparticles with small size and high dispersion can improve the performance of heterogeneous catalysts. To prepare graphene-supported Pd catalysts, graphene and PdCl₂ were used as support and Pd precursors, respectively. Pd/G-P and Pd/G-H catalysts were prepared by cold plasma and conventional thermal reduction, respectively, for the catalytic reduction of p-nitrophenol (4-NP). The reaction followed quasi-first-order kinetics, and the apparent rate constant of Pd/G-P and Pd/G-H was 0.0111 and 0.0042 s⁻¹, respectively. The graphene support was exfoliated by thermal reduction and cold plasma, which benefits the 4-NP adsorption. Pd/G-P presented a higher performance because cold plasma promoted the migration of Pd species to the support outer surface. The Pd/C atomic ratio for Pd/G-P and Pd/G-H was 0.014 and 0.010, respectively. In addition, the Pd nanoparticles in Pd/G-P were smaller than those in Pd/G-H, which was beneficial for the catalytic reduction. The Pd/G-P sample presented abundant oxygen-containing functional groups, which anchored the metal nanoparticles and enhanced the metal-support interaction. This was further confirmed by the shift in the binding energy to a high value for Pd3d in Pd/G-P. The cold plasma method operated under atmospheric pressure is effective for the preparation of Pd/G catalysts with enhanced catalytic activity for 4-NP reduction.

Magnetic polymer bowl for enhanced catalytic activity and recyclability

This work introduces the fabrication of a magnetic polymer bowl for enhanced catalytic activity and recyclability, which involves the synthesis of silica-coated Fe3O4 magnetic clusters, seeded dispersion polymerization using the magnetic clusters, and transformation into a bowl-like structure via a phase separation route. The additional treatment with tannic acid (TA) on the bowls allows the in situ formation of silver nanoparticles (AgNPs) on their surfaces. The openness and larger surface area of the bowls, as compared with those of other structured particles, such as spheres and flowers, enable a considerably higher immobilization of AgNPs, thus leading to an excellent catalytic reduction for 4-nitrophenol (4-NP), methylene blue (MB), and rhodamine B. Furthermore, the strong magnetic response originating from the magnetic clusters inside the bowls endows a good magnetic recovery and an excellent reusability for the repeated reduction of the organic dyes without loss of catalytic activity.

Ag/AgCl@MIL-88A(Fe) heterojunction ternary composites: towards the photocatalytic degradation of organic pollutants

The efficient utilization of solar energy has received tremendous interest due to the increasing environmental and energy concerns. The present paper discusses the efficient integration of a plasmonic photocatalyst (Ag/AgCl) with an iron-based metal-organic framework (MIL-88A(Fe)) for boosting the visible light photoreactivity of MIL-88A(Fe). Two composites of Ag/AgCl@MIL-88A(Fe), namely MAG-1 and MAG-2 (stoichiometric ratio of Fe to Ag is 5 : 1 and 2 : 1), were successfully synthesized via facile in situ hydrothermal methods followed by UV reduction. The synthesized composite materials are characterized by FTIR, PXRD, UVDRS, PL, FESEM/EDX, TEM and BET analyses. The Ag/AgCl@MIL-88A(Fe) (MAG-2) hybrid system shows excellent photocatalytic activity for the degradation of p-nitrophenol (PNP), rhodamine B (RhB), and methylene blue (MB) under sunlight. We found that 91% degradation of PNP in 80 min, 99% degradation of RhB in 70 min and 94% degradation of MB in 70 min have taken place by using MAG-2 as a catalyst under sunlight. The superior activity of Ag/AgCl@MIL-88A(Fe) (MAG-2) is attributed to the synergistic effects from the surface plasmon resonance (SPR) of Ag NPs and the electron transfer from MIL-88A(Fe) to Ag nanoparticles for effective separation of electron-hole pairs. Furthermore, the mechanism of degradation of PNP, RhB and MB is proposed by analyzing the electron transfer pathway in Ag/AgCl@MIL-88A(Fe).

Geochemical and Physicochemical Characteristics of Clay Materials from Congo with Photocatalytic Activity on 4-Nitrophenol in Aqueous Solutions

This study investigated the geochemical and physicochemical characteristics of natural clay collected in the Democratic Republic of Congo. The optical properties of the sample collected in Golf (GOL) were tested in the removal of 4-nitrophenol in aqueous solution. The geochemical analysis depicted that all the samples are plotted within the shale quadrant. Furthermore, the Chemical Index of Alteration (CIA) indicated that the samples are extremely weathered. The particle size distribution ranged from 0.41 to 418.6 μm, while the pore diameters for all the samples were under 100 Å. A flake-like surface morphology was observed in all the samples. SiO₂, Al₂O₃, Fe₂O₃, K₂O, and TiO₂ were the major chemical compounds found in all the samples, while the XRD analysis showed the presence of quartz, kaolinite, magnetite, and illite. The presence of metal oxides (i.e., TiO₂ and Fe₂O₃) indicated that these natural clays can be used for photocatalytic oxidation of pollutants. The sample collected in Katuba (KAT) displayed the higher reflectance percentages for the selected wavelengths except at 200 nm. Interestingly, the GOL sample exhibited lower energy band gaps (2.68 and 3.94 eV) necessary for photocatalysis. The untreated GOL clay sample removed 99.13% of 4-nitrophenol from aqueous solution through the photodegradation process. The usage of the untreated GOL clay could be a cost-effective solution in the removal of 4-nitrophenol in wastewater.

A Critical Review on Metal-Organic Frameworks and Their Composites as Advanced Materials for Adsorption and Photocatalytic Degradation of Emerging Organic Pollutants from Wastewater

Water-borne emerging pollutants are among the greatest concern of our modern society. Many of these pollutants are categorized as endocrine disruptors due to their environmental toxicities. They are harmful to humans, aquatic animals, and plants, to the larger extent, destroying the ecosystem. Thus, effective environmental remediations of these pollutants became necessary. Among the various remediation techniques, adsorption and photocatalytic degradation have been single out as the most promising. This review is devoted to the compilations and analysis of the role of metal-organic frameworks (MOFs) and their composites as potential materials for such applications. Emerging organic pollutants, like dyes, herbicides, pesticides, pharmaceutical products, phenols, polycyclic aromatic hydrocarbons, and perfluorinated alkyl substances, have been extensively studied. Important parameters that affect these processes, such as surface area, bandgap, percentage removal, equilibrium time, adsorption capacity, and recyclability, are documented. Finally, we paint the current scenario and challenges that need to be addressed for MOFs and their composites to be exploited for commercial applications.

Gold Nanozymes: From Concept to Biomedical Applications

In recent years, gold nanoparticles have demonstrated excellent enzyme-mimicking activities which resemble those of peroxidase, oxidase, catalase, superoxide dismutase or reductase. This, merged with their ease of synthesis, tunability, biocompatibility and low cost, makes them excellent candidates when compared with biological enzymes for applications in biomedicine or biochemical analyses. Herein, over 200 research papers have been systematically reviewed to present the recent progress on the fundamentals of gold nanozymes and their potential applications. The review reveals that the morphology and surface chemistry of the nanoparticles play an important role in their catalytic properties, as well as external parameters such as pH or temperature. Yet, real applications often require specific biorecognition elements to be immobilized onto the nanozymes, leading to unexpected positive or negative effects on their activity. Thus, rational design of efficient nanozymes remains a challenge of paramount importance. Different implementation paths have already been explored, including the application of peroxidase-like nanozymes for the development of clinical diagnostics or the regulation of oxidative stress within cells via their catalase and superoxide dismutase activities. The review also indicates that it is essential to understand how external parameters may boost or inhibit each of these activities, as more than one of them could coexist. Likewise, further toxicity studies are required to ensure the applicability of gold nanozymes in vivo. Current challenges and future prospects of gold nanozymes are discussed in this review, whose significance can be anticipated in a diverse range of fields beyond biomedicine, such as food safety, environmental analyses or the chemical industry.

An Overview and Evaluation of Highly Porous Adsorbent Materials for Polycyclic Aromatic Hydrocarbons and Phenols Removal from Wastewater

Polycyclic aromatic hydrocarbons (PAHs) and phenolic compounds had been widely recognized as priority organic pollutants in wastewater with toxic effects on both plants and animals. Thus, the remediation of these pollutants has been an active area of research in the field of environmental science and engineering. This review highlighted the advantage of adsorption technology in the removal of PAHs and phenols in wastewater. The literature presented on the applications of various porous carbon materials such as biochar, activated carbon (AC), carbon nanotubes (CNTs), and graphene as potential adsorbents for these pollutants has been critically reviewed and analyzed. Under similar conditions, the use of porous polymers such as Chitosan and molecularly imprinted polymers (MIPs) have been well presented. The high adsorption capacities of advanced porous materials such as mesoporous silica and metal-organic frameworks have been considered and evaluated. The preference of these materials, higher adsorption efficiencies, mechanism of adsorptions, and possible challenges have been discussed. Recommendations have been proposed for commercialization, pilot, and industrial-scale applications of the studied adsorbents towards persistent organic pollutants (POPs) removal from wastewater.

Highly sensitive and selective determination of p-nitrophenol at an interpenetrating networks structure of self-assembled rod-like lanthanum hydroxide-oxidized multi-walled carbon nanotubes nanocomposite

In this study, a novel electrochemical sensor based on self-assembled rod-like lanthanum hydroxide-oxidized multi-walled carbon nanotubes (La(OH)₃-OxMWCNTs) nanocomposite was developed for sensitive determination of p-nitrophenol (p-NP). The La(OH)₃-OxMWCNTs nanocomposite with an interpenetrating networks structure was characterized by field emission electron microscope (FE-SEM), Fourier transform infrared (FT-IR) spectroscopy, Raman spectra and X-ray photoelectron spectroscopy (XPS). The cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements were performed to study the electrochemical behaviors of La(OH)₃-OxMWCNTs modified glassy carbon electrode (La(OH)₃-OxMWCNTs/GCE). The La(OH)₃-OxMWCNTs/GCE was used for sensitive determination of p-NP by CV and linear sweep voltammetry (LSV). Under the optimum conditions, the peak currents of LSV versus the concentrations of p-NP in the range 1.0-30.0 μmol L^-1 showed a good linear relationship (R²=0.9971), and the limit of detection (LOD) was calculated to be 0.27 μmol L^-1 (signal-to-noise ratio of 3, S/N=3). The recoveries of p-NP in real samples of industrial wastewater and Xiangjiang water at La(OH)₃-OxMWCNTs/GCE were in the range of 95.62-110.75% with relative standard deviation (RSD) in the range of 1.65-3.85%. The intra-day and inter-day precisions were estimated to be less than 2.76% (n= 5), indicating that La(OH)₃-OxMWCNTs/GCE possessed highly stability. In addition, La(OH)₃-OxMWCNTs/GCE sensor showed good anti-interference ability for determination of p-NP in aqueous mixtures containing high concentrations of inorganic and organic interferents, and a decrease of oxidation peak currents by less than 3.57% relative to the initial levels indicated it possessed excellent selectivity. Therefore, La(OH)₃-OxMWCNTs/GCE could be used as a fast, selective and sensitive electrochemical sensor platform for the selective determination and quantification of aqueous p-NP.

Biogenesis of Prism-Like Silver Oxide Nanoparticles Using Nappa Cabbage Extract and Their p-Nitrophenol Sensing Activity

The present study aimed to explore the eco-friendly synthesis of prism-like silver oxide nanoparticles (Ag₂ONPs) from nappa cabbage extract and its p-nitrophenol sensing activity. The prepared Ag₂ONPs were characterized by X-ray diffraction (XRD), field-emission scanning spectroscopy (FESEM), energy-dispersive spectroscopy (EDS), transmission electron microscopy (TEM), and ultraviolet (UV)-visible light spectral analysis (UV-Vis). p-Nitrophenol sensing properties of the prepared nanoparticles were also determined using a simple I-V method. The results showed that the as-prepared Ag₂ONPs have a face-centered cubic (fcc) crystalline nature and a prism-like morphology with particle size in the range 21.61-92.26 nm. The result also showed a high intensity of the (111) facet, making the Ag₂ONP-carbon black/nickel foam electrode (Ag₂ONP-C/NFE) exhibit a high-performance response to p-nitrophenol spanning a wide range of concentrations from 1.0 mM to 0.1 pM and a response time of around 5 s, indicating a high potential for water treatment applications.

Controlled synthesis of Zeolite adsorbent from low-grade diatomite: A case study of self-assembled sodalite microspheres

Highly efficient and sustainable conversion technologies to generate uniform sodalite (Na₈(AlSiO₄)₆(OH)₂) zeolite microspheres with low-grade waste natural diatomite as raw materials via a solution-mediated crystallization route were developed in the present study. The synthesis process can be considered as an in-situ zeolitization of diatomite precursor without involving any mesoscale template and any post-synthetic modification. The mass ratios of diatomite and AlCl₃·6H₂O have remarkable effect on the morphology, crystal structure and porosity of sodalite zeolite product. The preferred sodalite microspheres with uniform mesoporous of size 3.5-5.5 nm and large surface area of 162.5 m²/g exhibit well removal performance for heavy metal ions (Pb(II), Cd(II), Zn(II), and Cu(II)), with the highest adsorption abilities for Pb(II) ions of 365 mg/g. In addition, the effect of contact time, initial ion concentration, competitive adsorption and solution pH were evaluated. The removal performance results from synergistic effects of dominating cation-exchange and additional surface chemisorption. The study may broadly help unveil chemical control reactions of the zeolitization processes of diatomite, and thus facilitates the development of promising zeolite materials for the use in natural and engineered aquatic environments by recycling waste diatomite resources.

Adsorption characteristics and mechanism of p-nitrophenol by pine sawdust biochar samples produced at different pyrolysis temperatures

Biochar is becoming a low-cost substitute of activated carbon for the removal of multiple contaminants. In this study, five biochar samples derived from pine sawdust were produced at different pyrolysis temperatures (300 °C–700 °C) and used adsorbents to remove p-nitrophenol from water. Results indicate that, as the pyrolysis temperature increases, the surface structure of biochar grows in complexity, biochar’s aromaticity and number of functional group decrease, and this material’s polarity increases. Biochar’s physiochemical characteristics and dosage, as well as solution’s pH and environmental temperature significantly influence the p-nitrophenol adsorption behavior of biochar. p-nitrophenol adsorption onto biochar proved to be an endothermic and spontaneous process; furthermore, a greater energy exchange was observed to take place when biochar samples prepared at high temperatures were utilized. The adsorption mechanism includes physical adsorption and chemisorption, whereas its rate is mainly affected by intra-particle diffusion. Notably, in biochar samples prepared at low temperature, adsorption is mainly driven by electrostatic interactions, whereas, in their high-temperature counterparts, p-nitrophenol adsorption is driven also by hydrogen bonding and π–π interactions involving functional groups on the biochar surface.

Adsorption driven formate reforming into hydride and tandem hydrogenation of nitrophenol to amine over PdOx catalysts

Due to their high toxicity and non-biodegradability, efficient reduction of nitroarenes to amines is of great practical importance, yet it still remains a significant challenge.

On-demand guest release from MOF-5 sealed with nitrophenylacetic acid photocapping groups

Recently, we demonstrated that triphenylacetic acid could be used to seal dye molecules within MOF-5, but guest release required the digestion of the framework by treatment with acid. We prepared the sterically bulky photocapping group [bis-(3-nitro-benzyl)-amino]-(3-nitro-phenyl)-acetic acid (PC1) that can prevent crystal violet dye diffusion from inside MOF-5 until removed by photolysis.

Metal-organic frameworks/carbon-based materials for environmental remediation: A state-of-the-art mini-review

In recent years, many research groups started to study the combination of metal-organic frameworks (MOFs) with nanocarbon materials, which showed the excellent improved performances than MOFs alone. The addition of carbon materials such as graphene oxides (GOs) and carbon nanotubes (CNTs) into MOFs can improve the physico-chemical properties of parent MOFs with excellent chemical robustness, high mechanical and distinguished electronic thermal robustness. These advantages facilitate the wider applications of MOFs/carbon materials (MOFs-C) in more research fields. This paper is devoted to reviewing the recent studies about the preparation and applications of MOFs-C in environmental remediation. This paper discusses the efficient adsorptive removal of a wide range of pollutants by MOFs-C, including organic contaminants and heavy metals from water as well as VOCs and some other toxic gases from atmospheric environment. Additionally, the catalytic performance of these nanocomposites for photocatalysis and Fenton-like oxidation of water pollutants is discussed in details. Meanwhile, the significant roles of nanocarbons and in-depth mechanisms for improved adsorption or catalysis are summarized. Finally, future perspectives on the development and application of MOFs-C composites for pollution remediation are presented at the end of this paper.

ZIF-8 derived ZnO/Zn6Al2O9/Al2O3 nanocomposite with excellent photocatalytic performance under simulated sunlight irradiation

The ZIF-8 derived ZnO/Zn₆Al₂O₉/Al₂O₃ nanocomposite exhibits an unprecedented photocatalytic degradation activity toward MO of high concentration.

Visible-light-driven CQDs@MIL-125(Ti) nanocomposite photocatalyst with enhanced photocatalytic activity for the degradation of tetracycline

In the present study, a novel photocatalyst, CQDs@MIL-125(Ti) (CQDs = carbon quantum dots), was prepared via a solvothermal procedure. The photocatalytic properties were tested by the degradation of tetracycline (TC) with a 250 W Xe lamp (λ > 420 nm). Compared with pure MIL-125(Ti), the 10 wt% CQDs@MIL-125(Ti) photocatalyst can significantly improve the degradation process of TC, and the degradation efficiency can reach 90% within 4 h. The enhancement in the photocatalytic performance is due to the CQDs, which can promote the absorption of visible light and also efficiently accelerate the separation of photogenerated electron–hole pairs. We have also demonstrated that superoxide radicals (·O₂⁻) and holes (h⁺) play crucial roles in the photocatalytic degradation of TC through capture experiments. The current work provides a new idea for constructing high-efficiency photocatalysts based on MIL-125(Ti).

A novel CQDs@MIL-125(Ti) photocatalyst had been synthesized by a facile solvothermal process for the degradation of TC. The possible degradation mechanism was proposed based on the active species trapping experiments.