Sol-gel derived nitric oxide-releasing oxygen sensors

Enhancing analytical accuracy of intravascular electrochemical oxygen sensors via nitric oxide release using S-nitroso-N-acetyl-penicillamine (SNAP) impregnated catheter tubing

Implantable medical devices are an integral part of primary/critical care. However, these devices carry a high risk for blood clots, caused by platelet aggregation on a foreign body surface. This study focuses on the development of a simplified approach to create nitric oxide (NO) releasing intravascular electrochemical oxygen (O₂) sensors with increased biocompatibility and analytical accuracy. The implantable sensors are prepared by embedding S-nitroso-N-acetylpenacillamine (SNAP) as the NO donor molecule in the walls of the catheter type sensors. The SNAP-impregnated catheters were prepared by swelling silicone rubber tubing in a tetrahydrofuran solution containing SNAP. Control and SNAP-impregnated catheters were used to fabricate the Clark-style amperometric PO₂ sensors. The SNAP-impregnated sensors release NO under physiological conditions for 18 d as measured by chemiluminescence. The analytical response of the SNAP-impregnated sensors was evaluated in vitro and in vivo. Rabbit and swine models (with sensors placed in both veins and arteries) were used to evaluate the effects on thrombus formation and analytical in vivo PO₂ sensing performance. The SNAP-impregnated PO₂ sensors were found to more accurately measure PO₂ levels in blood continuously (over 7 and 20 h animal experiments) with significantly reduced thrombus formation (as compared to controls) on their surfaces.

Nitric Oxide Release for Improving Performance of Implantable Chemical Sensors - A Review

Over the last three decades, there has been extensive interest in developing in vivo chemical sensors that can provide real-time measurements of blood gases (oxygen, carbon dioxide, and pH), glucose/lactate, and potentially other critical care analytes in the blood of hospitalized patients. However, clot formation with intravascular sensors and foreign body response toward sensors implanted subcutaneously can cause inaccurate analytical results. Further, the risk of bacterial infection from any sensor implanted in the human body is another major concern. To solve these issues, the release of an endogenous gas molecule, nitric oxide (NO), from the surface of such sensors has been investigated owing to NO's ability to inhibit platelet activation/adhesion, foreign body response and bacterial growth. This paper summarizes the importance of NO's therapeutic potential for this application and reviews the publications to date that report on the analytical performance of NO release sensors in laboratory testing and/or during in vivo testing.

Recent advances in thromboresistant and antimicrobial polymers for biomedical applications: just say yes to nitric oxide (NO)

Biomedical devices are essential for patient diagnosis and treatment; however, when blood comes in contact with foreign surfaces or homeostasis is disrupted, complications including thrombus formation and bacterial infections can interrupt device functionality, causing false readings and/or shorten device lifetime. Here, we review some of the current approaches for developing antithrombotic and antibacterial materials for biomedical applications. Special emphasis is given to materials that release or generate low levels of nitric oxide (NO). Nitric oxide is an endogenous gas molecule that can inhibit platelet activation as well as bacterial proliferation and adhesion. Various NO delivery vehicles have been developed to improve NO's therapeutic potential. In this review, we provide a summary of the NO releasing and NO generating polymeric materials developed to date, with a focus on the chemistry of different NO donors, the polymer preparation processes, and in vitro and in vivo applications of the two most promising types of NO donors studied thus far, N-diazeniumdiolates (NONOates) and S-nitrosothiols (RSNOs).

Improved in vivo performance of amperometric oxygen (PO2) sensing catheters via electrochemical nitric oxide generation/release

A novel electrochemically controlled release method for nitric oxide (NO) (based on electrochemical reduction of nitrite ions) is combined with an amperometric oxygen sensor within a dual lumen catheter configuration for the continuous in vivo sensing of the partial pressure of oxygen (PO2) in blood. The on-demand electrochemical NO generation/release method is shown to be fully compatible with amperometric PO2 sensing. The performance of the sensors is evaluated in rabbit veins and pig arteries for 7 and 21 h, respectively. Overall, the NO releasing sensors measure both venous and arterial PO2 values more accurately with an average deviation of -2 ± 11% and good correlation (R(2) = 0.97) with in vitro blood measurements, whereas the corresponding control sensors without NO release show an average deviation of -31 ± 28% and poor correlation (R(2) = 0.43) at time points >4 h after implantation in veins and >6 h in arteries. The NO releasing sensors induce less thrombus formation on the catheter surface in both veins and arteries (p < 0.05). This electrochemical NO generation/release method could offer a new and attractive means to improve the biocompatibility and performance of implantable chemical sensors.

Nitric oxide release from polydimethylsiloxane-based polyurethanes

Localized nitric oxide (NO) release from polymeric materials holds much promise for the prevention of coagulation often associated with implantable and extracorporeal blood-contacting devices. Films of polyurethane (PU) containing incorporated polyethyleneimine were thus exposed to NO gas to form diazeniumdiolates (NONOates) in situ. Donor incorporation and NO gas exposure did not affect the mechanical properties of the films. The NO release capacity increased with increasing polydimethylsiloxane (PDMS) content in the soft segment of the PU: total capacity could be more than doubled (P<0.05) from 0.093 ± 0.028 to 0.225 ± 0.004 mmol/g when the PDMS content was increased from 0 to 100%. Release kinetics were best approximated using a modified Korsemeyer-Peppas power law (R²=0.95-0.99). Despite the resultant rapid initial decrease in NO release rates, values above that observed for quiescent endothelial cells (0.83 pmol·cm⁻²·s⁻¹) were maintained for extended periods of 5-10 days, while rates above that of a stimulated endothelium (2.7-6.8 pmol·cm⁻²·s⁻¹) were achieved for the first 24 hours. This method of NONOate formation may be advantageous, as potential premature NO release by exposure of diazeniumdiolated donors during incorporation, processing and storage, can be avoided by in situ diazoniumdiolation closer to the time of implantation.

Nitric oxide releasing Tygon materials: studies in donor leaching and localized nitric oxide release at a polymer-buffer interface

Tygon is a proprietary plasticized poly(vinyl chloride) polymer that is used widely in bioapplications, specifically as extracorporeal circuits. To overcome issues with blood clot formation and infection associated with the failure of these medical devices upon blood contact, we consider a Tygon coating with the ability to release the natural anticlotting and antibiotic agent, nitric oxide (NO), under simulated physiological conditions. These coatings are prepared by incorporating 20 w/w% S-nitrosoglutathione (GSNO) donor into a Tygon matrix. These films release NO on the order of 0.64 ± 0.5 × 10(-10) mol NO cm(-2) min(-1), which mimics the lower end of natural endothelium NO flux. We use a combination of assays to quantify the amount of GSNO that is found intact at different time points throughout the film soak, as well as monitor the total thiol content in the soaking solution due to any analyte that has leached from the polymer film. We find that a burst of GSNO is released from the material surface within 5 min to 1 h of soaking, which only represents 0.25% of the total GSNO contained in the film. After 1 h of film soak, no additional GSNO is detected in the soaking solution. By further considering the total thiol content in solution relative to the intact GSNO, we demonstrate that the amount of GSNO leached from the material into the buffer soaking solution does not contribute significantly to the total NO released from the GSNO-incorporated Tygon film (<10% total NO). Further surface analysis using SEM-EDS traces the elemental S on the material surface, demonstrating that within 5 min -1 h soaking time, 90% of the surface S is removed from the material. Surface wettability and roughness measurements indicate no changes between the GSNO-incorporated films pre- to postsoak that will be significant toward the adsorption of biological components, such as proteins, relative to the presoaked donor-incorporated film. Overall, we demonstrate that, for a 20 w/w% GSNO-incorporated Tygon film, relatively minimal GSNO leaching is experienced, and the lost GSNO is from the material surface. Varying the donor concentration from 5 to 30 w/w% GSNO within the film does not result in significantly different NO release profiles. Additionally, the steady NO flux associated with the system is predominantly due to localized release from the material, and not donor lost to soaking solution. The surface properties of these materials generally imply that they are useful for blood-contacting applications.

Nitric oxide release: part II. Therapeutic applications

A wide range of nitric oxide (NO)-releasing materials has emerged as potential therapeutics that exploit NO's vast biological roles. Macromolecular NO-releasing scaffolds are particularly promising due to their ability to store and deliver larger NO payloads in a more controlled and effective manner compared to low molecular weight NO donors. While a variety of scaffolds (e.g., particles, dendrimers, and polymers/films) have been cleverly designed, the ultimate clinical utility of most NO-releasing macromolecules remains unrealized. Although not wholly predictive of clinical success, in vitro and in vivo investigations have enabled a preliminary evaluation of the therapeutic potential of such materials. In this tutorial review, we review the application of macromolecular NO therapies for cardiovascular disease, cancer, bacterial infections, and wound healing.

Basic science review: nitric oxide--releasing prosthetic materials

Prosthetic devices that come into contact with blood ultimately fail secondary to thrombus formation. This limits the utility of a variety of materials used to surgically treat cardiovascular disease, including vascular grafts and stents, as well as sensors and catheters placed within the circulatory system. Moreover, systemic anticoagulation that is used to prevent malfunction of these devices has potential for serious complications. It is known that nitric oxide (NO) produced via the endothelium imparts thromboresistant properties to native blood vessels. Thus, if NO were delivered locally to the site of the prosthetic material, it has the potential to halt thrombus formation while limiting life-threatening side effects. This review serves to examine the variety of NO-releasing materials that have been created with the two different classes of NO donors, the diazeniumdiolates and S-nitrosothiols, and the clinical applications of these prosthetics for potential future use.

Xerogel optical sensor films for quantitative detection of nitroxyl

Xerogel sensing films were synthesized via sol-gel chemistry were used to fabricate optical nitroxyl (HNO) sensors [corrected] Selective detection of HNO in solution was achieved by monitoring the rates of manganese(III) meso-tetrakis(4-sulfonatophenyl) porphyrinate (MnIIITPPS) reductive nitrosylation in the anaerobic interior of aminoalkoxysilane-derived xerogel films. Nitroxyl permeability in sensor films deposited in round-bottom 96-well plates was enhanced via incorporation of trimethoxysilyl-terminated poly(amidoamine-organosilicon) dendrimers in the xerogel network. The selectivity of MnIIITPPS for HNO, the overall sensitivity, and the working dynamic range of the resulting sensors were characterized. The HNO-sensing microtiter plates were used to quantify pH-dependent HNO generation by the recently described HNO-donor sodium 1-(isopropylamino)diazene-1-ium-1,2-diolate (IPA/NO), and compare HNO production efficiency between IPA/NO and Angeli's salt, a traditional HNO-donor.

Nitric oxide-releasing xerogel-based fiber-optic pH sensors

A xerogel-based optical pH sensor capable of releasing low levels of nitric oxide (NO) and measuring changes in solution pH is reported. Through simple dip-coating procedures, aminoalkoxysilane-based xerogel films modified with N-diazeniumdiolate NO donor precursors and the fluorescent pH indicator seminaphthorhodamine-1 carboxylate (SNARF-1) were sequentially deposited onto optical fibers. The resulting sensors were characterized by fast and linear response to pH throughout the physiological range (pH 7.0-7.8). Real-time chemiluminescence measurements confirmed that the presence of the overlying SNARF-1-containing TMOS layer did not have an inhibitory effect on N-diazeniumdiolate formation or NO release, and the NO-releasing coatings were capable of maintaining NO fluxes >0.4 pmol/cm(2) s up to 16 h. In vitro blood compatibility studies using porcine platelets confirmed the expected thromboresistivity of the NO-releasing xerogel coatings.

Poly(vinylpyrrolidone)-doped nitric oxide-releasing xerogels as glucose biosensor membranes

Nitric oxide (NO)-releasing xerogel membranes were prepared as coatings for an electrochemical glucose biosensor to allow for enhanced biocompatibility while maintaining adequate response times and sensitivity. Formation of the NO-donor species was found to drastically decrease the permeability of the aminosilane-based xerogels to both hydrogen peroxide and glucose. The addition of poly(vinylpyrrolidone) (PVP) polymer enhanced the membrane permeability even after exposure to high pressures of NO (necessary for NO-donor synthesis). The analytical response and NO release of PVP-doped NO-releasing xerogels as glucose sensor membranes were further investigated and found to be enhanced via polymer doping. Doping of the polymer into the xerogel did not compromise the stability of the xerogel as evaluated by silicon leaching studies. Despite the addition of PVP, the NO-releasing xerogels maintained reduced bacterial adhesion characteristics analogous to previous reports for NO-releasing xerogels.

Improving the biocompatibility of in vivo sensors via nitric oxide release

The continuous, real-time monitoring of clinically important analytes (e.g., PO2, PCO2, pH, K+, Na+, glucose, and lactate) is of great importance to human health care. Despite considerable efforts spanning several decades, the use of in vivo sensors clinically remains limited due to inadequate biocompatibility. The discovery of nitric oxide (NO) as an effective inhibitor of platelet and bacterial adhesion has opened a new direction of research related to designing the next generation of in vivo sensors. In this Highlight article, recent progress in designing more biocompatible in vivo sensors is described, with a particular focus on preparing interfaces that resist biofouling via controlled NO release.

Recent advances in analytical chemistry--a material approach

Advancements of materials research have profound direct impacts on developments in analytical chemistry and may hold the key to improvement of existing or new techniques at present times and near future. Applications of materials in analytical chemistry are reviewed, with focus on sensors, separations and extraction techniques. This review aims to survey examples of interesting works carried out in the last five years over a broad spectrum of materials classified as hybrids, nanomaterials and biomolecular materials.