Fluorinated TiO2 Hollow Spheres for Detecting Formaldehyde under UV Irradiation

The fluorinated titanium dioxide (F-TiO2) hollow spheres with varying F to Ti molar ratios were prepared by a simple one-step hydrothermal method followed by thermal processing. The diameter of the F-TiO2-0.3 hollow spheres with a nominal ratio of F:Ti = 0.3:1 was about 200-400 nm. Compared with the sensor based on pristine TiO2 sensing materials, the F-TiO2-0.3 sensor displayed an enhanced sensing performance toward gaseous formaldehyde (HCHO) vapor at room temperature under ultraviolet (UV) light irradiation. The F-TiO2-0.3 sensor demonstrated an approximately 18-fold enhanced response (1.56) compared to the pristine TiO2 sensor (0.085). The response and recovery times of the F-TiO2-0.3 sensor to 10 ppm HCHO were about 56 s and 64 s, respectively, and a limit-of-detection value of 0.5 ppm HCHO was estimated. The F-TiO2-0.3 sensor also demonstrated good repeatability and selectivity to HCHO gas under UV light irradiation. The outstanding HCHO gas-sensing properties of the F-TiO2-0.3 sensor were related to the following factors: the excitation effect caused by the UV light facilitated surface chemical reactions with analyte gas species; the hollow sphere structure provided sufficient active sites; and the surface fluoride (≡Ti-F) created additional chemisorption sites on the surface of the TiO2 material.

Few-Layer Fullerene Network for Photocatalytic Pure Water Splitting into H2 and H2 O2

A few-layer fullerene network possesses several advantageous characteristics, including a large surface area, abundant active sites, high charge mobility, and an appropriate band gap and band edge for solar water splitting. Herein, we report for the first time that the few-layer fullerene network shows interesting photocatalytic performance in pure water splitting into H2 and H2 O2 in the absence of any sacrificial reagents. Under optimal conditions, the H2 and H2 O2 evolution rates can reach 91 and 116 μmol g-1  h-1 , respectively, with good stability. This work demonstrates the novel application of the few-layer fullerene network in the field of energy conversion.

Photocatalytic treatment of real liquid effluent from hydrothermal carbonization of agricultural waste using metal doped TiO2/UV system

This study investigated treatment of real liquid effluent generated from hydrothermal carbonization (HTC) of macadamia nut shell by employing transition metals Cu, Ni, and Fe doped titanium dioxide (TiO₂) photocatalysts. The anatase TiO₂ based photocatalysts were prepared via sol-gel method, and calcined at 400 °C. The modification with metal dopants was performed via ultrasonic assisted incipient wetness impregnation method. The prepared photocatalysts were characterized using XRD, UV-Vis DRS, SEM-EDX, and N₂ physisorption. The influence of metal dopants, types of TiO₂ support, and initial pH of the wastewater on the photocatalytic degradation performance of total organic carbon (TOC) and chemical oxygen demand (COD) in the wastewater were investigated. The results revealed that Fe doped TiO₂ exhibited the highest photocatalytic activity followed by Cu and Ni, respectively. Among all, Fe doped anatase TiO₂ were the most promising catalyst as it performed the highest removal of 75.1% for TOC and 94.1% for COD after 1 h irradiation at pH 4, achieving the lowest TOC and COD concentration of 405.62 mg/L and 91.26 mg/L, respectively. The findings suggested that photocatalytic degradation of HTC liquid effluent could be a potential treatment before releasing the wastewater to the environment.

Hydrothermal/solvothermal synthesis and treatment of TiO2 for photocatalytic degradation of air pollutants: Preparation, characterization, properties, and performance

Photocatalytic oxidation (PCO) is a well-known technology for air purification and has been extensively studied for removal of many air pollutants. Titanium dioxide (TiO₂) is the most investigated photocatalyst in the field of environmental remediation owed to its chemical stability, non-toxicity, and suitable positions of valence and conduction bands. Various preparation techniques including sol-gel, flame hydrolysis, water-in-oil microemulsion, chemical vapour deposition, solvothermal, and hydrothermal have been employed to obtain TiO₂ materials. Hydro-/Solvothermal (HST) synthesis, focus of the present work, can be defined as a preparation method in which crystal growth occurs in a solvent at relatively low temperature (<200 °C) and above atmospheric pressure. This paper aims to provide a comprehensive and critical review of current knowledge regarding the application of HST synthesis for fabrication of TiO₂ nanostructures for indoor air purification. TiO₂ nanostructures are categorized from the morphological standpoint (e.g. nanoparticles, nanotubes, nanosheets, and hierarchically porous) and discussed in detail. The influence of preparation parameters including hydrothermal time, temperature, pH of the reaction medium, solvent, and calcination temperature on physical, chemical, and optical properties of TiO₂ is reviewed. Considering the complex interplay among catalyst properties, a special emphasis is placed on elucidating the interconnection between various photocatalyst features and their impacts on photocatalytic activity.

Enhanced photocatalytic degradation of sulfamethoxazole by zinc oxide photocatalyst in the presence of fluoride ions: Optimization of parameters and toxicological evaluation

The presence of antibiotics in water bodies has received increasing attention since they are continuously introduced and detected in the environment and may cause unpredictable environmental hazards and risks. The photocatalytic degradation of sulfamethoxazole (SMX) by ZnO in the presence of fluoride ions (F-ZnO) was evaluated. The effects of operating parameters on the efficiency of SMX removal were investigated by using response surface methodology (RSM). Under the optimum condition, i.e. photocatalyst dosage = 1.48 g/L, pH 4.7, airflow rate = 2.5 L/min and the concentration of fluoride ions = 2.505 mM, about 97% SMX removal was achieved by F-ZnO after 30 min of reaction. The mechanism of reactions, COD removal efficiency and reaction kinetics were also investigated under optimum operating conditions. In addition, about 85% COD reduction was obtained after 90 min photocatalytic reaction. The pseudo-first-order kinetics rate constants for the photodegradation of SMX were found to be 0.099, 0.058 and 0.048 min^-1 by F-ZnO, ZnO and TiO₂ (P25), respectively. The figure-of-merit electrical energy per order (E_EO) was used for estimating the electrical energy efficiency, which was shown to be considerably lower than the energy consumption for the reported research on removal of SMX by photocatalytic degradation under UV irradiation. Toxicity assays were conducted by measuring the inhibition percentage (PI) towards E. coli bacteria strain and by agar well diffusion method. The results showed that after 30 min of reaction, the toxicity of the treated solutions by all photocatalysts fell within the non-toxic range; however, the reduction in toxicity by F-ZnO was faster than those by ZnO and P25. Despite the positive effects of surface fluorination of ZnO on the SMX and COD removal and reaction kinetics, its lower stability compared to ZnO and P25 in the repeated experiments gave rise to some doubts about its performance from a practical point of view.

Formic acid enhanced effective degradation of methyl orange dye in aqueous solutions under UV-Vis irradiation

Developing efficient technologies to treat recalcitrant organic dye wastewater has long been of great research and practical interest. In this study, a small molecule, formic acid (FA), was applied as a process enhancer for the degradation of methyl orange (MO) dye as a model recalcitrant organic pollutant in aqueous solutions under the condition of UV-Vis light irradiation and air aeration at the ambient temperature of 25 °C. It was found that the decolouration of the dye solutions can be rapidly achieved, reducing the time, for example, from around 17.6 h without FA to mostly about less than 2 h with the presence of FA. The mineralization rate of MO dye reached as high as 81.8% in 1.5 h in the case of initial MO dye concentration at 25 mg L(-1), which is in contrast to nearly no mineralization of the MO dye for a similar system without the FA added. The study revealed that the generation of the H2O2 species in the system was enhanced and the produced OH radicals effectively contributed to the degradation of the MO dye. Process parameters such as the initial concentration of MO dye, FA dosage and solution pH were all found to have some effect on the degradation efficiency under the same condition of UV-Vis light irradiation and air aeration. The MO dye degradation performance was found to follow a first-order reaction rate to the MO dye concentration in most cases and there existed a positive correlation between the reaction rate constant and the initial FA concentration. Compared to the traditional H2O2/UV-Vis oxidation system, the use of FA as a process-enhancing agent can have the advantages of low cost, easy availability, and safe to use. The study hence demonstrates a promising approach to use a readily available small molecule of FA to enhance the degradation of recalcitrant organic pollutants, such as MO dye, especially for their pre-treatment.

Unraveling the Multiple Effects Originating the Increased Oxidative Photoactivity of {001}-Facet Enriched Anatase TiO2

Crystal shape control on a series of anatase photocatalysts was achieved by varying the amount of HF employed as a capping agent in their hydrothermal synthesis. A systematic comparison between their physicochemical properties, determined by several complementary surface and bulk techniques before and after thermal treatment at 500 °C, allowed one to discern the influence of the relative amount of exposed {001} crystal facets among a series of effects simultaneously affecting their oxidative photocatalytic activity. The results of both formic acid and terephthalic acid photo-oxidation test reactions point to the primary role played by calcination in making {001} facets effectively photoactive. Annealing not only removes most of the residual fluorine capping agent from the photocatalyst surface, thus favoring substrate adsorption, but also produces morphological modifications to a crystal packing that makes accessible a larger portion of surface {001} facets due to the unpiling of platelike crystals. The photocatalyst bearing the highest amount of exposed {001} facets (60%) shows the highest photoactivity in both the direct and the (•)OH-radical-mediated photocatalytic test reaction.

Brookite TiO2 photocatalyzed degradation of phenol in presence of phosphate, fluoride, sulfate and borate anions

A significant enhancement of phenol degradation over brookite TiO₂ in presence of phosphate, fluoride, sulfate and borate anions is reported.

Facile fabrication of 3D flower-like heterostructured g-C3N4/SnS2 composite with efficient photocatalytic activity under visible light

The formation of heterojunction between g-C₃N₄ and SnS₂ greatly enhanced the photocatalytic activity of g-C₃N₄/SnS₂ compared with the mechanical mixed g-C₃N₄/SnS₂.

Different recycle behavior of Cu2+ and Fe3+ ions for phenol photodegradation over TiO2 and WO3

Photocatalytic degradation of organic pollutants on TiO2 and WO3 have been widely studied, but the effects of Cu(2+) and Fe(3+) ions still remain unclear. In this work, we have found that the recycle behavior of Cu(2+) and Fe(3+) are greatly dependent on the photocatalytic activity of metal oxide used. With TiO2 (P25, anatase, and rutile), all the time profiles of phenol degradation in water under UV light well fitted to the apparent first-order rate equation. On the addition of Cu(2+), phenol degradation on anatase, rutile and WO3 also followed the first-order kinetics. On the addition of Fe(3+), the initial rate of phenol degradation on each oxide was increased, but only the reactions on three TiO2 became to follow the first order kinetics after half an hour. The relevant rate constants for phenol degradation in the presence of Cu(2+) or Fe(3+) were larger than those in the absence of metal ions. Under visible light, phenol degradation on WO3 was also accelerated on the addition of Fe(3+) or Cu(2+). Moreover, several influencing factors were examined, including the metal ion photolysis in solution. It becomes clear that as electron scavengers of TiO2 and WO3, Fe(3+) is better than Cu(2+), while they are better than O2. We propose that Fe(3+) recycle occurs through H2O2, photogenerated from TiO2, not from WO3, while Cu(2+) regeneration on a moderate photocatalyst is through the dissolved O2 in water.

Fluorinated semiconductor photocatalysts: tunable synthesis and unique properties

Semiconductor photocatalysts are of great significance in solar energy conversion and environmental remediation. To overcome serious drawbacks of these materials with respect to narrow light-response range and low quantum efficiency, a variety of strategies have been developed in the past decades to enhance the light harvesting and excitation as well as the charge transfer against recombination. In particular, fluorination of semiconductor photocatalysts can be employed to modify their surface and bulk properties, and consequently, to enhance their photocatalytic performance. This review presents a comprehensive description of the F-mediated synthesis and unique properties of fluorinated semiconductor photocatalysts, in particular titanium dioxide (TiO(2)). The available strategies for the synthesis of fluorinated photocatalysts include post-synthesis fluorination and in-situ fluorination. Depending on the synthesis route and conditions, it is possible to control the chemical nature of incorporated fluorine (such as adsorbed fluoride and lattice-doped fluorine) and the fluoride-mediated crystal modification and organization, which often results in exceptional surface and bulk physicochemical properties, giving rise to unique photocatalytic properties. Significantly, the surface fluorination induces unusual adsorption behavior and interfacial charge transfer dynamics, directly affecting photocatalytic redox properties of the surface-fluorinated photocatalysts. The lattice fluorine-doping, sole or cooperative with other complementary co-dopants, introduces special localized electronic structures and surface defect states, accounting for the exceptional visible-light photoactivity of the fluorine-doped photocatalysts. Finally, recent advances in the synthesis and properties of fluorinated photocatalysts are summarized along with perspectives on further developments in this area of research.

Photocatalytic degradation of aromatic pollutants: a pivotal role of conduction band electron in distribution of hydroxylated intermediates

The modulation of the yield distribution of intermediates formed in the photocatalytic degradation of organic pollutants is of extreme importance for the application of photocatalysis in environmental cleanup, as different intermediates usually exhibit distinct biological toxicity and secondary reactivity. In this paper, we report that the distribution of monohydroxylated intermediates (m-, p- and o-) formed during the photocatalytic oxidation of aromatic compounds changes with the variation of reaction conditions, such as O(2) partial pressure and substrate concentration. By detailed product analysis, theoretical calculation, and oxygen isotope labeling experiments, we show that these changes are due to the selective reduction of HO-adduct radicals (the precursors of hydroxylated intermediates) by conduction band electrons (e(cb)(-)) back to the original substrate, that is, p- and o-HO-adduct radicals are more susceptible to e(cb)(-) than the m- one. Our experiments give an example that, even under oxidative conditions, the yield distribution of isomeric intermediates can be modulated by e(cb)(-)-initiated reduction. This study also illustrates that the unique redox characteristics of photocatalysis, that is, both oxidation and reduction reactions take place on or near the surface of a single nanoparticle, can provide opportunities for the reaction control.

Cr(VI) photocatalytic reduction: effects of simultaneous organics oxidation and of gold nanoparticles photodeposition on TiO2

Commercial TiO(2) samples with different phase composition and surface area were tested as photocatalysts in the photoinduced reduction of Cr(VI) in aqueous suspensions at pH 3.7 under UV-visible light irradiation. This reaction was also coupled with the simultaneous photocatalytic oxidation of the pollutant azo dye Acid Orange 8 (AO8) and of formic acid, acting as hole scavengers. The co-presence of oxidizable and reducible species ensured better separation of photogenerated charge carriers, resulting in a higher rate of both organics' oxidation and Cr(VI) reduction, especially in the case of high surface area anatase TiO(2), having the strongest affinity for Cr(VI) and AO8, as demonstrated by competitive adsorption tests. The effects on Cr(VI) photocatalytic reduction of gold nanoparticles photodeposited on TiO(2) and of the Au loading were also investigated, aiming at ascertaining if this noble metal plays a role in the electron transfer processes involved in Cr(VI) reduction.

Effect of surface fluorination on the electrochemical and photoelectrocatalytic properties of nanoporous titanium dioxide electrodes

Titanium dioxide is a widely used photocatalyst whose properties can be modified by fluoride adsorption. This work is focused on the effect of surface fluorination on the electrochemical and photoelectrocatalytic properties of TiO(2) nanoporous thin films. Surface fluorination was achieved by simple addition of HF to the working solution (pH 3.5). Open circuit potential as well as ex situ XPS measurements verify that surface modification takes place. Fluorination triggers a significant capacitance increase in the accumulation potential region, as revealed by dark voltammetric measurements for all the TiO(2) samples studied. The photoelectrocatalytic properties (measured as photocurrents under white light illumination) depend on the substrate being oxidized and, in some cases, on the nature of the TiO(2) sample. In particular, the results obtained for electrodes prepared with a mixed phase (rutile + anatase) commercial nanopowder (PI-KEM) indicate that the processes mediated by surface trapped holes, such as the photooxidation of water or methanol, are accelerated while those occurring by direct hole capture from the adsorbed state (formic acid) are retarded. The photooxidation of catechol and phenol is also enhanced upon fluorination. In such a case, the effect can be rationalized on the basis of a diminished recombination and a surface displacement of both the oxidizable organic substrates and the poisoning species formed as a result of the organics oxidation. Photoelectrochemical and in situ infrared spectroscopic measurements support these ideas. In a more general vein, the results pave the way toward a better understanding of the photocatalysis phenomena, unravelling the importance of the reactant adsorption processes.

Absorption and action spectra analysis of ammonium fluoride-doped titania photocatalysts

The photocatalytic behaviour of a series of ammonium fluoride (NH(4)F)-doped titania (TiO(2)) photocatalysts was investigated in the decomposition of acetic acid in aqueous suspensions and in the gas phase mineralization of acetaldehyde. Very similar photocatalytic activity trends, usually increasing with increasing the calcination temperature for a given nominal dopant amount, were obtained for the two test reactions. Moderately doped TiO(2) calcined at 700 °C, consisting of pure anatase, was the best performing photocatalyst in both reactions. The photocatalytic oxidation of acetic acid was investigated systematically as a function of irradiation wavelength, by collecting so-called action spectra. By comparing the shapes of the action spectra with those of the absorption spectra of the investigated photocatalysts a model is proposed, based on spectral features deconvolution, which allows a clear distinction between inactive light absorption and effective photoactivity in acetic acid decomposition.

Enhanced sorption and photodegradation of chlorophenol over fluoride-loaded TiO2

The presence of NaF in the aqueous suspension of TiO(2) can accelerate the photocatalytic degradation of organic pollutants. However, disposal of such a fluoride-containing wastewater is not allowed by environmental regulation. In the present work, we report on surface modification of TiO(2) with a hardly water soluble salt, fluorite and fluorapatite. The modified catalysts at low loading displayed a higher activity than bare TiO(2) for the sorption and photocatalytic degradation of phenol and 2,4-dichlorophenol in water. A kinetic study using butanol as hydroxyl radical scavenger revealed that the fluoride-modified catalysts produced more hydroxyl radicals than bare TiO(2). Five repeated experiments showed that the fluorapatite-modified TiO(2) was very stable, and could be re-used without significant loss in activity.

Effect of fluorination on the surface properties of titania P25 powder: an FTIR study

A study was carried out on the consequences of the -OH(surf)/F(-) exchange occurring at the surface of TiO(2) P25 when suspended in HF/F(-) solutions. The maximum extent of fluorination was reached at pH 3.0, resulting in the fixation on the surface of ca. 2.5 F(-)/nm(2). The surface features of fluorinated samples under two selected conditions were investigated by IR spectroscopy, in comparison with pristine TiO(2). The collected data suggested that bridged -OH(surf), likely located on regular facets, was more resistant to exchange with F(-). Combined high resolution transmission electron microscopy (HRTEM), inductively coupled plasma mass spectrometry (ICP-MS) and IR measurements indicated that the fluorination performed in the adopted condition did not induce any etching of TiO(2) particles, and the -OH(surf)/F(-) exchange appeared reversible by treatment in concentrated basic solutions. Furthermore, fluorination resulted in an increase of the Lewis acid strength of surface Ti(4+) sites, which, as a consequence, retained adsorbed water molecules even after outgassing at 423 K. Such an effect involved the overwhelming majority of cations exposed on regular facets.