Meso-Macroporous Hydroxyapatite Powders Synthesized in Polyvinyl Alcohol or Polyvinylpyrrolidone Media

Mesoporous hydroxyapatite (HA) is widely used in various applications, such as the biomedical field, as a catalytic, as a sensor, and many others. The aim of this work was to obtain HA powders by means of chemical precipitation in a medium containing a polymer-polyvinyl alcohol or polyvinylpyrrolidone (PVP)-with concentrations ranging from 0 to 10%. The HA powders were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, atomic emission spectroscopy with inductively coupled plasma, electron paramagnetic resonance, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The specific surface area (SSA), pore volume, and pore size distributions were determined by low-temperature nitrogen adsorption measurements, and the zeta potential was established. The formation of macropores in powder agglomerates was determined using SEM and TEM. The synthesis in 10% PVP increased the SSA from 101.3 to 158.0 m2/g, while the ripening for 7 days led to an increase from 112.3 to 195.8 m2/g, with the total pore volume rising from 0.37 to 0.71 cm3/g. These materials could be classified as meso-macroporous HA. Such materials can serve as the basis for various applications requiring improved textural properties and may lay the foundation for the creation of bulk 3D materials using a technique that allows for the preservation of their unique pore structure.

Sol-Gel-Controlled Size and Morphology of Mesoporous Silica Microspheres Using Hard Templates

Mesoporous silica microspheres (MPSMs) represent a promising material as a stationary phase for HPLC separations. The use of hard templates provides a preparation strategy for producing such monodisperse silica microspheres. Here, 15 MPSMs were systematically synthesized by varying the sol-gel reaction parameters of water-to-precursor ratio and ammonia concentration in the presence of a porous p(GMA-co-EDMA) polymeric hard template. Changing the sol-gel process factors resulted in a wide range of MPSMs with varying particle sizes from smaller than one to several micrometers. The application of response surface methodology allowed to derive quantitative predictive models based on the process factor effects on particle size, pore size, pore volume, and specific surface area of the MPSMs. A narrow size distribution of the silica particles was maintained over the entire experimental space. Two larger-scale batches of MPSMs were prepared, and the particles were functionalized with trimethoxy(octadecyl) silane for the application as stationary phase in reversed-phases liquid chromatography. The separation of proteins and amino acids was successfully accomplished, and the effect of the pore properties of the silica particles on separation was demonstrated.

Circular Design and Functionalized Upcycling of Waste Commodity Polystyrene via C-H Activation Using Microwave-Assisted Multicomponent Synthesis

The inefficient reuse and recycling of plastics-and the current surge of medical and take-out food packaging use during the pandemic-have exacerbated the environmental burden. This impels the development of alternative recycling/upcycling methods to pivot toward circularity. We report the use of the Mannich three-component coupling reaction for the modification of polystyrene (PS) recovered with a 99.1% yield from waste food containers to form functionalized nitrogen and oxygen-rich PS derivatives. A series of functionalized PS with increasing moles of formaldehyde (F) and morpholine (M) (0.5 × 10^-2, 1.0 × 10^-2, and 2.0 × 10^-2 mol) was achieved using a sol-gel-derived Fe-TiO₂ catalyst in a solvent-free, microwave-assisted synthesis. Modified polymers were characterized with viscometry, ¹H NMR, ¹³CNMR (DEPT) FTIR, XPS, UV, and TGA. Functionalization scaled with an increasing ratio, validating the 3CR approach. Further functionalization was constrained by a competing oxidative degradation; however, the varying hydrogen bond density due to nitrogen and oxygen-rich species at higher ratios was shown to compensate for molecular weight loss. The integration of the N-cyclic quaternary ammonium cations exhibited the potential of functionalized polymers for ion-exchange membrane applications.

Semiconducting MOFs on ultraviolet laser-induced graphene with a hierarchical pore architecture for NO2 monitoring

Due to rapid urbanization worldwide, monitoring the concentration of nitrogen dioxide (NO₂), which causes cardiovascular and respiratory diseases, has attracted considerable attention. Developing real-time sensors to detect parts-per-billion (ppb)-level NO₂ remains challenging due to limited sensitivity, response, and recovery characteristics. Herein, we report a hybrid structure of Cu₃HHTP₂, 2D semiconducting metal-organic frameworks (MOFs), and laser-induced graphene (LIG) for high-performance NO₂ sensing. The unique hierarchical pore architecture of LIG@Cu₃HHTP₂ promotes mass transport of gas molecules and takes full advantage of the large surface area and porosity of MOFs, enabling highly rapid and sensitive responses to NO₂. Consequently, LIG@Cu₃HHTP₂ shows one of the fastest responses and lowest limit of detection at room temperature compared with state-of-the-art NO₂ sensors. Additionally, by employing LIG as a growth platform, flexibility and patterning strategies are achieved, which are the main challenges for MOF-based electronic devices. These results provide key insight into applying MOFtronics as high-performance healthcare devices.

Monodisperse Porous Silica/Polymer Nanocomposite Microspheres with Tunable Silica Loading, Morphology and Porosity

Hybrid organic/inorganic nanocomposites combine the distinct properties of the organic polymer and the inorganic filler, resulting in overall improved system properties. Monodisperse porous hybrid beads consisting of tetraethylene pentamine functionalized poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) particles and silica nanoparticles (SNPs) were synthesized under Stoeber sol-gel process conditions. A wide range of hybrid organic/silica nanocomposite materials with different material properties was generated. The effects of n(H₂O)/n(TEOS) and c(NH₃) on the hybrid bead properties particle size, SiO₂ content, median pore size, specific surface area, pore volume and size of the SNPs were studied. Quantitative models with a high robustness and predictive power were established using a statistical and systematic approach based on response surface methodology. It was shown that the material properties depend in a complex way on the process factor settings and exhibit non-linear behaviors as well as partly synergistic interactions between the process factors. Thus, the silica content, median pore size, specific surface area, pore volume and size of the SNPs are non-linearly dependent on the water-to-precursor ratio. This is attributed to the effect of the water-to-precursor ratio on the hydrolysis and condensation rates of TEOS. A possible mechanism of SNP incorporation into the porous polymer network is discussed.

Catalytic ozonation of dichloromethane at low temperature and even room temperature on Mn-loaded catalysts

Five Mn-loaded catalysts were synthesized on γ-Al2O3, TiO2, ZrO2, nano γ-Al2O3 and nanoZrO2 supports. The catalytic ozonation of DCM (dichloromethane) was evaluated under industrial conditions (i.e., temperature, O3 input, H2O and SO2 content). According to results, >90% DCM conversion without O3 residue was achieved for all samples at 120 °C and an O3/DCM ratio of 6. At 20-120 °C, the highest Mn3+ content, abundant surface oxygen species and more weak acid sites led to the best performance of Mn/nanoAl2O3 (M/A-II). At 20 °C and 120 °C, 80% and 95% DCM can be degraded respectively on M/A-II at 20 °C with matched surface oxygen species and acidity. An O3/DCM ratio of 6 was optimal for performance and economy. For the effects of complex exhaust, both H2O and SO2 deactivated M/A-II. The H2O-induced deactivation was recoverable and also removed surface-deposited chlorine-containing species, enhancing the HCl selectivity. Finally, the Cl equilibrium of the reaction was comprehensively analyzed.

Hierarchically porous and mechanically stable monoliths from ordered mesoporous silica and their water filtration potential

Mechanically stable structures with interconnected hierarchical porosity combine the benefits of both small and large pores, such as high surface area, pore volume, and good mass transport capabilities. Hence, lightweight micro-/meso-/macroporous monoliths are prepared from ordered mesoporous silica COK-12 by means of spark plasma sintering (SPS, S-sintering) and compared to conventionally (C-) sintered monoliths. A multi-scale model is developed to fit the small angle X-ray scattering data and obtain information on the hexagonal lattice parameters, pore sizes from the macro to the micro range, as well as the dimensions of the silica population. For both sintering techniques, the overall mesoporosity, hexagonal pore ordering, and amorphous character are preserved. The monoliths' porosity (77-49%), mesopore size (6.2-5.2 nm), pore volume (0.50-0.22 g cm-3), and specific surface area (451-180 m2 g-1) decrease with increasing processing temperature and pressure. While the difference in porosity is enhanced, the structural parameters between the C-and S-sintered monoliths are largely converging at 900 °C, except for the mesopore size and lattice parameter, whose dimensions are more extensively preserved in the S-sintered monoliths, however, coming along with larger deviations from the theoretical lattice. Their higher mechanical properties (biaxial strength up to 49 MPa, 724 MPa HV 9.807 N) at comparable porosities and ability to withstand ultrasonic treatment and dead-end filtration up to 7 bar allow S-sintered monoliths to reach a high permeance (2634 L m-2 h-1 bar-1), permeability (1.25 × 10-14 m2), and ability to reduce the chemical oxygen demand by 90% during filtration of a surfactant-stabilized oil in water emulsion, while indicating reasonable resistance towards fouling.

Pseudomorphic synthesis of bimodal porous silica microspheres for size-exclusion chromatography of small molecules

In this work, mesoporous silica microspheres with bimodal porous structures for size exclusion chromatography (SEC) supports were synthesized via a pseudomorphic transformation method by using 3.5 and 5 μm commercial silica particles as sources and cetyltrimethylammonium bromide (CTAB) as a template. The effects of the synthetic conditions on the pore size distribution were examined, including the temperature, reaction time and the molar ratio of SiO₂:NaOH. Bimodal porous silicas (BPSs) with pore sizes of 3.01 and 12.80 nm were obtained with SiO₂:NaOH:CTAB:H₂O=1:0.1:0.1:20 at 80 °C for 24 h. The BPSs were bonded with diol groups to produce a stationary phase for SEC. The column performance was evaluated with three types of samples, namely, dextran (70 KDa-62 Da), polyethene glycol (PEG) (20 KDa-32 Da) and three biomolecules (36 KDa-1.36 KDa). The column that was packed with a 3.5 μm stationary phase showed excellent resolution for molecular weights of less than 1 KDa with high column efficiency. Carbohydrate samples (dextran (MW=1296), dextran (MW=972), sucrose (MW=342), glucose (MW=180) and glycerol (MW=92)) were separated. Heptaethylene glycol, hexaethylene glycol, pentaethylene glycol, tetraethylene glycol, triethylene glycol, and diethylene glycol were resolved in a PEG200 sample. In summary, this work shows the advantages of bimodal mesopores in SEC for small molecules less than 1 kDa. In the pseudomorphic synthesis, the pore size can be regulated by template micelles. Thus, the development SEC supports with high accuracy for a specified molecular weight range is expected since the pore size can be regulated by the surfactant template.

Mesostructuring layered materials: self-supported mesoporous layered double hydroxide nanotubes

Synthesis of layered materials exhibiting hierarchical porosity remains challenging, but nevertheless worthwhile because it turns such solids into functional materials with high specific surface area. Using a soft-templating strategy in combination with the incorporation of 8-fold coordinated Eu3+, self-assembly of self-supported layered double hydroxide (LDH) nanotubes has been achieved. Heteromorphic equimolar substitution of Al3+ by Eu3+ in Zn2+/Al3+ LDH solids intercalated with 1,3,5-benzenetricarboxylate anions (BTC) assists precipitation of the double hydroxide layers onto the convex surface of Pluronic® P-123 worm-like micelles, yielding multilayer cylinders of BTC-intercalated LDHs. Removal of the micellar template is easily achieved by liquid extraction with methanol, yielding a network of interconnected, well-defined, self-supported, multi-walled, hollow cylindrical nanotubes. Removal of Eu3+ from the synthesis disables formation of the nanotubular morphology, but still yields LDHs containing a network of embedded mesopores, resulting in a specific surface area that is 5-fold higher as compared to standard LDHs.

ZIF-8 calcination derived Cu2O–ZnO* material for enhanced visible-light photocatalytic performance

The mechanism of TC degradation over Cu₂O–ZnO* rich in oxygen vacancies.

Hierarchically structured porous materials: synthesis strategies and applications in energy storage

To address the growing energy demands of sustainable development, it is crucial to develop new materials that can improve the efficiency of energy storage systems. Hierarchically structured porous materials have shown their great potential for energy storage applications owing to their large accessible space, high surface area, low density, excellent accommodation capability with volume and thermal variation, variable chemical compositions and well controlled and interconnected hierarchical porosity at different length scales. Porous hierarchy benefits electron and ion transport, and mass diffusion and exchange. The electrochemical behavior of hierarchically structured porous materials varies with different pore parameters. Understanding their relationship can lead to the defined and accurate design of highly efficient hierarchically structured porous materials to enhance further their energy storage performance. In this review, we take the characteristic parameters of the hierarchical pores as the survey object to summarize the recent progress on hierarchically structured porous materials for energy storage. This is the first of this kind exclusively to survey the performance of hierarchically structured porous materials from different porous characteristics. For those who are not familiar with hierarchically structured porous materials, a series of very significant synthesis strategies of hierarchically structured porous materials are firstly and briefly reviewed. This will be beneficial for those who want to quickly obtain useful reference information about the synthesis strategies of new hierarchically structured porous materials to improve their performance in energy storage. The effect of different organizational, structural and geometric parameters of porous hierarchy on their electrochemical behavior is then deeply discussed. We outline the existing problems and development challenges of hierarchically structured porous materials that need to be addressed in renewable energy applications. We hope that this review can stimulate strong intuition into the design and application of new hierarchically structured porous materials in energy storage and other fields.

Manganese oxides with hierarchical structures derived from coordination polymers and their enhanced catalytic activity at low temperature for selective catalytic reduction of NOx

Hierarchical manganese oxides with enhanced catalytic performance have been successfully synthesized via simple thermal annealing of manganese coordination polymer precursors, which is a facile, cost-effective, and environmentally benign preparation method. The resultant manganese oxide particles formed hierarchical structures with a starfish-like morphology and exhibited enhanced low-temperature SCR performance below 200 °C without dopants or supporting materials. In addition, the morphology, chemical states, crystal structure and acidity of manganese oxide catalysts prepared at different calcination temperatures were investigated. It is elucidated that enhanced SCR catalytic performance was strongly dependent on the hierarchical morphology of the catalysts.

A Critical Review of Solid Materials for Low-Temperature Thermochemical Storage of Solar Energy Based on Solid-Vapour Adsorption in View of Space Heating Uses

The present report deals with low-temperature thermochemical storage for space heating, which is based on the principles of vapour adsorption onto solid adsorbents. With the aim of obtaining comprehensive information on the rationalized selection of adsorbents for heat storage in open sorption systems operating in the moist-air flow mode, various materials reported up to now in the literature are reviewed by referring strictly to the possible mechanisms of water vapour adsorption, as well as practical aspects of their preparation or their application under particular operating conditions. It seems reasonable to suggest that, on the basis of the current state-of-the-art, the adsorption phenomenon may be rather exploited in the auxiliary heating systems, which provide additional heat during winter's coldest days.

Independent Tailoring of Macropore and Mesopore Space in TiO2 Monoliths

TiO₂ monoliths were synthesized by a partially hindered sol-gel process. Various synthesis parameters like precursor concentrations and gelation temperature were varied to investigate changes in the macroporosity (being in the range of micrometers) and to determine influences on the macropore formation mechanism. Ionic liquids (ILs) were used as templates to vary the mesopore size independently from the macropore size. Depending on the synthesis parameters, TiO₂ monoliths with exclusive mesoporosity or with hierarchical meso-/macropore structure were received, and the range of macropores can be shifted between 100 nm and 10 μm without influencing the mesopore diameter. Pore volumes up to 880 mm³/g were achieved, as determined by mercury intrusion porosimetry. The mesopores' diameter can be adjusted between 6 and 25 nm by adding different amounts of IL, and surface areas up to 260 m²/g and mesopore volumes of 0.5 cm³/g were obtained, based on N₂-physisorption measurements. The monoliths were cladded by polymer, allowing for studying the flow-through properties depending on the macropore size. This precise control for tailored macropores enables the design of optimized TiO₂ monoliths with respect to the desired application requirements.

Electrostatic attraction of nanoobjects – a versatile strategy towards mesostructured transition metal compounds

This highlight summarizes current challenges of mesostructuring and focuses on the scope and the potential of the ELAN – (electrostatic attraction of nanoobjects) strategy in mesostructuring of transition metal compounds.

Waxberry-like hierarchically porous ethyl-bridged hybrid silica microsphere: A substrate for enzyme catalysis and high-performance liquid chromatography

In this study, the ethyl-bridged hybrid silica microsphere with hierarchically meso-macroporous structure was initially synthesized through a method combining dispersion polymerization with sol-gel transition and phase separation. The flow-through macropores rendered the microsphere a rough surface like a waxberry, and thus the material was named as waxberry-like ethyl-bridged hybrid silica sphere (WEHS). WEHS was characteristic of appropriate alkali-stability, which was highly difficult for the pure silica. Additionally, WEHS possessed hierarchical meso- and macropores, which added additional value for faster mass transfer than the conventional fully porous silica materials. Taking the advantages of WEHS, it was successfully applied as the substrate to immobilize lipase; the prepared immobilized lipase exhibited high catalytic activity and favorable reusability under alkaline conditions, which was significant in pitch control of neutral-alkaline papermaking industry. Moreover, as the high-performance liquid chromatographic stationary phase matrix, WEHS made the separation under alkaline mobile phase into a reality for the silica-based materials. Besides, an ultra-fast and efficient separation in minutes was achieved with lower consumption of solvents and saving analytical time, which is highly desired in modern analysis. In general, WEHS was a novel and promising candidate in the myriads of silica-based materials.

Single-atomic cobalt sites embedded in hierarchically ordered porous nitrogen-doped carbon as a superior bifunctional electrocatalyst

Exploring efficient and cost-effective catalysts to replace precious metal catalysts, such as Pt, for electrocatalytic oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) holds great promise for renewable energy technologies. Herein, we prepare a type of Co catalyst with single-atomic Co sites embedded in hierarchically ordered porous N-doped carbon (Co-SAS/HOPNC) through a facile dual-template cooperative pyrolysis approach. The desirable combination of highly dispersed isolated atomic Co-N₄ active sites, large surface area, high porosity, and good conductivity gives rise to an excellent catalytic performance. The catalyst exhibits outstanding performance for ORR in alkaline medium with a half-wave potential (E _1/2) of 0.892 V, which is 53 mV more positive than that of Pt/C, as well as a high tolerance of methanol and great stability. The catalyst also shows a remarkable catalytic performance for HER with distinctly high turnover frequencies of 0.41 and 3.8 s^-1 at an overpotential of 100 and 200 mV, respectively, together with a long-term durability in acidic condition. Experiments and density functional theory (DFT) calculations reveal that the atomically isolated single Co sites and the structural advantages of the unique 3D hierarchical porous architecture synergistically contribute to the high catalytic activity.

Under Diffusion Control: from Structuring Matter to Directional Motion

Self-organization in synthetic chemical systems is quickly developing into a powerful strategy for designing new functional materials. As self-organization requires the system to exist far from thermodynamic equilibrium, chemists have begun to go beyond the classical equilibrium self-assembly that is often applied in bottom-up supramolecular synthesis, and to learn about the surprising and unpredicted emergent properties of chemical systems that are characterized by a higher level of complexity and extended reactivity networks. The present review focuses on self-organization in reaction-diffusion systems. Selected examples show how the emergence of complex morphogenesis is feasible in synthetic systems leading to hierarchically and nanostructured matter. Starting from well-investigated oscillating reactions, recent developments extend diffusion-limited reactivity to supramolecular systems. The concept of dynamic instability is introduced and illustrated as an additional tool for the design of smart materials and actuators, with emphasis on the realization of motion even at the macroscopic scale. The formation of spatio-temporal patterns along diffusive chemical gradients is exploited as the main channel to realize symmetry breaking and therefore anisotropic and directional mechanical transformations. Finally, the interaction between external perturbations and chemical gradients is explored to give mechanistic insights in the design of materials responsive to external stimuli.

Hierarchically organized honeycomb films through block copolymer directed self-assembly in "breath figure" templating and soft microwave-triggered annealing

Hierarchically organized polymer films are produced with a high level of order from the combination of block copolymer nanophase segregation, "breath figure" methodology and microwave irradiation. A block copolymer based on poly(methyl methacrylate) and poly(n-butylacrylate) featuring cylindrical nanopatterns is involved in the "breath figure" process to create a microporous honeycomb structure. These films are submitted to microwave annealing to enhance the degree of ordering of the nano-segregation without the destruction of the honeycomb microstructure, which is not possible by classical thermal or solvent annealing. Ellipsometry, optical and atomic force microscopy are used to study three key parameters; the substrate nature, the film thickness and the microwave irradiation power. The silicon wafer is the substrate of choice to efficiently act as the heating transfer element and 60 seconds at 10 watts are enough to nicely order the 1 μm thick copolymer films. These conditions are eventually applied on hierarchically organized polymer films to obtain a hexagonal array of 100 nm deep holes within a matrix of perpendicularly aligned nano-cylinders.

Rational Design of Co(II) Dominant and Oxygen Vacancy Defective CuCo2O4@CQDs Hollow Spheres for Enhanced Overall Water Splitting and Supercapacitor Performance

The hierarchical CuCo₂O₄@carbon quantum dots (CQDs) hollow microspheres constructed by 1D porous nanowires have been successfully prepared through a simple CQDs-induced hydrothermal self-assembly technique. XPS analysis shows the CuCo₂O₄@CQDs possesses the Co(II)-rich surface associated with the oxygen vacancies, which can effectively boost the Faradaic reactions and oxygen evolution reaction (OER) activity. For example, the as-synthesized 3D porous CuCo₂O₄@CQDs electrode exhibits high activity toward overall electrochemical water splitting, for example, an overpotential of 290 mV for OER and 331 mV for hydrogen evolution reaction (HER) in alkaline media have been achieved at 10 mA cm^-2, respectively. Furthermore, an asymmetric supercapacitor (ASC) (CuCo₂O₄@CQDs//CNTs) delivers a high energy density of 45.9 Wh kg^-1 at 763.4 W kg^-1, as well as good cycling ability. The synergy of Co(II)-rich surface, oxygen vacancies, and well-defined 3D hollow structures facilitates the subsequent surface electrochemical reactions. This work presents a facile method to fabricate energetic nanocomposites with highly reactive, durable, and universal functionalities.

Volatile Organic Compound Gas-Sensing Properties of Bimodal Porous α-Fe2O3 with Ultrahigh Sensitivity and Fast Response

Porous solid with multimodal pore size distribution provides plenty of advantages including large specific surface area and superior mass transportation to achieve high gas-sensing performances. In this study, α-Fe₂O₃ nanoparticles with bimodal porous structures were prepared successfully through a nanocasting pathway, adopting the bicontinuous 3D cubic symmetry mesoporous silica KIT-6 as the hard template. Its structure and morphology were characterized by X-ray diffraction, nitrogen adsorption-desorption, transmission electron microscopy, and so on. Furthermore, the gas sensor fabricated from this material exhibited excellent gas-sensing performance to several volatile organic compounds (acetone, ethyl acetate, isopropyl alcohol, n-butanol, ethanol, and methanol), such as ultrahigh sensitivity, rapid response speed (less than 10 s) and recovery time, good reproducibility, as well as stability. These would be associated with the desirable pore structure of the material, facilitating the molecules diffusion toward the entire sensing surface, and providing more active sensing sites for analytical gas.

Long chain ionic liquid-assisted synthesis of PS/Pd beads and hierarchical porous Pd–SiO2

Long-chain ionic liquid, 1-hexadecyl-3-methylimidazolium chloride (C₁₆mimCl), was firstly used as a linking agent to construct polystyrene (PS)/C₁₆mimCl/palladium (Pd) beads. Subsequently, the PS/C₁₆mimCl/Pd beads were used as a macroporous templating agent and C₁₆mimCl was used as a mesoporous templating agent to prepare Pd-loaded hierarchical porous silica. A systematic study was carried out addressing the influence of the amount of C₁₆mimCl and the mass ratios of m(Pd)/m(PS) on the PS/C₁₆mimCl/Pd beads and the Pd-loaded hierarchical porous structures. The samples were characterized by electrophoresis experiments, SEM, TEM, small-angle XRD, and N₂ adsorption–desorption experiments. It was found that the coverage of citrate-coated Pd nanoparticles (Pd NPs) onto the PS beads can be simply tailored by changing the amount of C₁₆mimCl and the mass ratios of m(Pd)/m(PS). The resultant Pd-loaded hierarchical porous silica possessed a 3D ordered macroporous skeleton with a specific surface area of up to 967 m² g⁻¹, ordered mesoporous silica walls (SBA-3 type) and well-dispersed Pd NPs anchored on the inner walls of the spherical macroporous hollow. Importantly, the obtained Pd-loaded hierarchical porous silica exhibited an enhanced catalytic activity for the oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) by H₂O₂.

1-Hexadecyl-3-methylimidazolium chloride (C₁₆mimCl) can be used as “bridges” to prepare PS/C₁₆mimCl/Pd beads, and Pd-loaded hierarchical porous silica was synthesized using dual templates of the PS/C₁₆mimCl/Pd beads and C₁₆mimCl.

Preparation of macroporous scaffolds with holes in pore walls and pressure driven flows through them

Controlling the pore architecture in macroporous scaffolds has important implications for their use as reactor packings and as catalyst supports.

Hierarchically ordered macro–mesoporous anatase TiO2 prepared by pearl oyster shell and triblock copolymer dual templates for high photocatalytic activity

Hierarchically ordered macro–mesoporous anatase TiO₂ is prepared by combining the supramolecular-templating self-assembly of amphiphilic triblock copolymer P123 with a natural pearl oyster shell in a hard-templating process by a facile sol–gel reaction. The obtained materials are characterized by Raman spectroscopy, X-ray diffraction, N₂ adsorption–desorption analysis, scanning electron microscopy, and transmission electron microscopy. The results demonstrate that all TiO₂ materials obtained after calcination at various temperatures are in the anatase phase, and interestingly the resultant ordered structure of both macropores and mesopores are well-preserved after calcination at 350 °C or 450 °C, with the walls of macropores composed of ordered mesopores. However, upon calcination at 550 °C or 650 °C, while the ordered macroporous structures remain well-preserved, the mesoporous structures collapse. The photocatalytic activities of the resulting TiO₂ materials are also evaluated by photodegradation of rhodamine B under UV light irradiation. The prepared TiO₂ calcined at 450 °C shows the highest photocatalytic activity.

Hierarchically ordered macro–mesoporous anatase TiO₂ with photocatalytic activity was prepared using triblock copolymer P123 and natural pearl oyster shell as dual templates.

Nano-engineered hierarchical porous silicas for enhanced catalytic efficiency in the liquid phase

By tailoring the pore properties (size, morphology and orientation) of hierarchical catalysts, we show experimentally the importance of active phase accessibility on catalytic efficiency.

Effect of a Swelling Agent on the Performance of Ni/Porous Silica Catalyst for CH4-CO2 Reforming

Hierarchical porous materials are of great interest in various industrial applications because of their potential to overcome the mass transport limitations typically encountered for single-mode porous materials. This report describes the synthesis of a hierarchical trimodal porous silica-based material using a 7.5 molar ratio of a relatively inexpensive nonionic surfactant template, triblock copolymer P123, EO₂₀PO₇₀EO₂₀. The pore size distribution curve shows the presence of three types of pores with average diameters of ∼8, 25, and 89 nm. Electron microscope images confirm the existence of smaller ordered mesopores (first mode), larger ordered mesopores (second mode), and macropores (third mode). Ni nanoparticles dispersed on this trimodal porous silica produce a material that exhibited excellent catalytic performance for the CO₂ reforming of CH₄. This research provides new insights that will facilitate the development of trimodal porous silica (TMS) materials for a variety of applications. The results demonstrated that the presence of large pores (second and third mode pores) in TMS material increased the number of accessible active Ni sites, which led to the high activity observed for Ni/TMS catalyst.

Impact of Macroporosity on Catalytic Upgrading of Fast Pyrolysis Bio-Oil by Esterification over Silica Sulfonic Acids

Fast pyrolysis bio-oils possess unfavorable physicochemical properties and poor stability, in large part, owing to the presence of carboxylic acids, which hinders their use as biofuels. Catalytic esterification offers an atom- and energy-efficient route to upgrade pyrolysis bio-oils. Propyl sulfonic acid (PrSO₃ H) silicas are active for carboxylic acid esterification but suffer mass-transport limitations for bulky substrates. The incorporation of macropores (200 nm) enhances the activity of mesoporous SBA-15 architectures (post-functionalized by hydrothermal saline-promoted grafting) for the esterification of linear carboxylic acids, with the magnitude of the turnover frequency (TOF) enhancement increasing with carboxylic acid chain length from 5 % (C₃ ) to 110 % (C₁₂ ). Macroporous-mesoporous PrSO₃ H/SBA-15 also provides a two-fold TOF enhancement over its mesoporous analogue for the esterification of a real, thermal fast-pyrolysis bio-oil derived from woodchips. The total acid number was reduced by 57 %, as determined by GC×GC-time-of-flight mass spectrometry (GC×GC-ToFMS), which indicated ester and ether formation accompanying the loss of acid, phenolic, aldehyde, and ketone components.

Sol-gel synthesis of monolithic materials with hierarchical porosity

The development of synthetic routes to hierarchically organized porous materials containing multiple, discrete sets of pores having disparate length scales is of high interest for a wide range of applications. One possible route towards the formation of multilevel porous architectures relies on the processing of condensable, network forming precursors (sol-gel processes) in the presence of molecular porogens, lyotropic mesophases, supramolecular architectures, emulsions, organic polymers, or ice. In this review the focus is on sol-gel processing of inorganic and organic precursors with concurrently occurring microscopic and/or macroscopic phase separation for the formation of self-supporting monoliths. The potential and the limitations of the solution-based approaches is presented with special emphasis to recent examples of hierarchically organized silica, metal oxides and phosphates as well as carbon monoliths.

Tracking Single DNA Nanodevices in Hierarchically Meso-Macroporous Antimony-Doped Tin Oxide Demonstrates Finite Confinement

Housing bio-nano guest devices based on DNA nanostructures within porous, conducting, inorganic host materials promise valuable applications in solar energy conversion, chemical catalysis, and analyte sensing. Herein, we report a single-template synthetic development of hierarchically porous, transparent conductive metal oxide coatings whose pores are freely accessible by large biomacromolecules. Their hierarchal pore structure is bimodal with a larger number of closely packed open macropores (∼200 nm) at the higher rank and with the remaining space being filled with a gel network of antimony-doped tin oxide (ATO) nanoparticles that is highly porous with a broad size range of textual pores mainly from 20-100 nm at the lower rank. The employed carbon black template not only creates the large open macropores but also retains the highly structured gel network as holey pore walls. Single molecule fluorescence microscopic studies with fluorophore-labeled DNA nanotweezers reveal a detailed view of multimodal diffusion dynamics of the biomacromolecules inside the hierarchically porous structure. Two diffusion constants were parsed from trajectory analyses that were attributed to free diffusion (diffusion constant D = 2.2 μm²/s) and to diffusion within an average confinement length of 210 nm (D = 0.12 μm²/s), consistent with the average macropore size of the coating. Despite its holey nature, the ATO gel network acts as an efficient barrier to the diffusion of the DNA nanostructures, which is strongly indicative of physical interactions between the molecules and the pore nanostructure.

Adsorptive removal of phosphate from water using mesoporous materials: A review

Mesoporous materials have significant potential for use as adsorbents for removal of phosphate from water. The chemical and structural properties of materials greatly affect their capacity and rate in the phosphate adsorption process. This paper reviews recent activities in the development of mesoporous materials as phosphate adsorbents. In particular, it mainly focuses on the synthesis, properties and phosphate removal efficiency of various materials with mesoporosity, including metal-coordinated amino-functionalized silicas, ammonium-functionalized silicas, metal-doped mesoporous silicas, metal oxides, metal sulfate and carbon.

In Situ Synthesis Strategy for Hierarchically Porous Ni2P Polyhedrons from MOFs Templates with Enhanced Electrochemical Properties for Hydrogen Evolution

The development of highly active and stable noble metal-free electrocatalysts of hydrogen evolution reaction (HER) under both acidic and basic conditions for renewable-energy conversion techniques is of great significance. Herein, a practical in situ synthesis strategy for a three-dimensional Ni₂P polyhedron with a hierarchically porous structure was presented, which was efficiently obtained from a nickel centered metal-organic frameworks (MOF-74-Ni) by direct low-temperature phosphorization. The as-prepared Ni₂P polyhedron showed a high BET surface area (175.0 m²·g^-1), hierarchically porous property, and outstanding metal dispersion, which well inherited the morphology and porosity of its MOF precursor. Compared with Ni₂P particles obtained from a nonporous precursor, the as-prepared Ni₂P polyhedron used as electrocatalyst exhibited excellent electrocatalytic performance toward the HER, with a low overpotential of 158 mV to produce the cathodic current density of 10 mA cm^-2. A small Tafel slope of 73 mV per decade is obtained for Ni₂P polyhedron, which revealed a Volmer-Heyrovsky mechanism during the HER. In addition, benefiting from the structural stability, the porous Ni₂P polyhedron used as a electrocatalyst showed satisfactory long-term durability for the HER in acidic media.

A facile template route to periodic mesoporous organosilicas nanospheres with tubular structure by using compressed CO2

Periodic mesoporous organosilicas (PMOs) nanospheres with tubular structure were prepared with compressed CO₂ using cationic and anionic mixed surfactant (CTAB/SDS) and triblock copolymer Pluronic P123 as bi-templates. TEM, N₂ adsorption-desorption, solid NMR, and FTIR were employed to characterize the obtained materials. Compressed CO₂ severed as acidic reagent to promote the hydrolysis of organosilicas, and could tune the morphology and structure of the obtained PMOs nanomaterials simple by adjusting the CO₂ pressure during the synthesis process. Rhodamine B (RB) and Ibuprofen (IBU), as the model dye and drug, were loaded into the prepared nanomaterials to reveal its adsorption and desorption ability. Furthermore, different molars of the surfactant (CTAB/SDS) and organosilane precursor (BTEB) were investigated to show the effect of the surfactant concentration on the morphology and structure of the PMOs prepared with compressed CO₂, and some different structures were obtained. A possible mechanism for the synthesis of PMOs with tubular structure using compressed CO₂ was proposed based on the experimental results.