Curable, biodegradable elastomers: emerging biomaterials for drug delivery and tissue engineering

Degradable Cell-Adhesive Hybrid Hydrogels by Cross-Linking of Gelatin with Poly(2-isopropenyl-2-oxazoline)

This study focused on the cross-linking of poly(2-isopropenyl-2-oxazoline) (PiPOx) with gelatin to obtain strong, degradable hybrid hydrogels with good cell adhesion. The molecular weight and concentration of PiPOx and the PiPOx-to-gelatin ratio were varied to adjust the mechanical and swelling properties of the hybrid hydrogels. The swelling degree of PiPOx-gelatin hydrogels in water ranged between 1260 and 810%, with the corresponding Young's compressive moduli ranging from 77 to 215 kPa. Rheological measurements demonstrated the mechanical stability of the hydrogels. The hydrogels exhibited substantial degradation in Dulbecco's phosphate-buffered saline (DPBS) and cell culture medium within several weeks, indicating their degradability and responsiveness. The cell adhesion assay with primary human foreskin fibroblasts revealed the hybrid hydrogels are noncytotoxic and support cell attachment and proliferation. These strong hydrogels thus show excellent potential as biomedical cell scaffolds, combining the tunability and strength of PiPOx hydrogels with gelatin's cell-interactive properties while the ester-containing cross-links provide tunable degradability.

In Vitro and In Vivo Degradation of Photo-Crosslinked Poly(Trimethylene Carbonate-co-ε-Caprolactone) Networks

Three-armed poly(trimethylene carbonate) (PTMC) and poly(trimethylene carbonate-co-Ɛ-caprolactone) (P(TMC-co-ε-CL)) macromers with molecular weights of approximately 30 kg mol-1 are synthesized by ring-opening polymerization and subsequent functionalization with methacrylic anhydride. Networks are then prepared by photo-crosslinking. To investigate the in vitro and in vivo degradation properties of these photo-crosslinked networks and assess the effect of ε-caprolactone content on the degradation properties, PTMC networks, and copolymer networks with two different TMC:ε-CL ratios are prepared. PTMC networks degraded slowly, via an enzymatic surface erosion process, both in vitro and in vivo. Networks prepared from P(TMC-co-ε-CL) macromers with a 74:26 ratio are found to degrade slowly as well, via a surface erosion process, albeit at a higher rate compared to PTMC networks. Increasing the ε-CL content to a ratio of 52:48, resulted in a faster degradation. These networks lost their mechanical properties much sooner than the other networks. Thus, PTMC and P(TMC-co-ε-CL) networks are interesting networks for tissue engineering purposes and the exact degradation properties can be tuned by varying the TMC:ε-CL ratio, providing researchers with a tool to obtain copolymer networks with the desired degradation rate depending on the intended application.

Strategies for Development of Synthetic Heart Valve Tissue Engineering Scaffolds

The current clinical solutions, including mechanical and bioprosthetic valves for valvular heart diseases, are plagued by coagulation, calcification, nondurability, and the inability to grow with patients. The tissue engineering approach attempts to resolve these shortcomings by producing heart valve scaffolds that may deliver patients a life-long solution. Heart valve scaffolds serve as a three-dimensional support structure made of biocompatible materials that provide adequate porosity for cell infiltration, and nutrient and waste transport, sponsor cell adhesion, proliferation, and differentiation, and allow for extracellular matrix production that together contributes to the generation of functional neotissue. The foundation of successful heart valve tissue engineering is replicating native heart valve architecture, mechanics, and cellular attributes through appropriate biomaterials and scaffold designs. This article reviews biomaterials, the fabrication of heart valve scaffolds, and their in-vitro and in-vivo evaluations applied for heart valve tissue engineering.

Sustainable Elastomers for Actuators: "Green" Synthetic Approaches and Material Properties

Elastomeric materials have great application potential in actuator design and soft robot development. The most common elastomers used for these purposes are polyurethanes, silicones, and acrylic elastomers due to their outstanding physical, mechanical, and electrical properties. Currently, these types of polymers are produced by traditional synthetic methods, which may be harmful to the environment and hazardous to human health. The development of new synthetic routes using green chemistry principles is an important step to reduce the ecological footprint and create more sustainable biocompatible materials. Another promising trend is the synthesis of other types of elastomers from renewable bioresources, such as terpenes, lignin, chitin, various bio-oils, etc. The aim of this review is to address existing approaches to the synthesis of elastomers using "green" chemistry methods, compare the properties of sustainable elastomers with the properties of materials produced by traditional methods, and analyze the feasibility of said sustainable elastomers for the development of actuators. Finally, the advantages and challenges of existing "green" methods of elastomer synthesis will be summarized, along with an estimation of future development prospects.

Elastomer-Hydrogel Systems: From Bio-Inspired Interfaces to Medical Applications

Novel advanced biomaterials have recently gained great attention, especially in minimally invasive surgical techniques. By applying sophisticated design and engineering methods, various elastomer-hydrogel systems (EHS) with outstanding performance have been developed in the last decades. These systems composed of elastomers and hydrogels are very attractive due to their high biocompatibility, injectability, controlled porosity and often antimicrobial properties. Moreover, their elastomeric properties and bioadhesiveness are making them suitable for soft tissue engineering. Herein, we present the advances in the current state-of-the-art design principles and strategies for strong interface formation inspired by nature (bio-inspiration), the diverse properties and applications of elastomer-hydrogel systems in different medical fields, in particular, in tissue engineering. The functionalities of these systems, including adhesive properties, injectability, antimicrobial properties and degradability, applicable to tissue engineering will be discussed in a context of future efforts towards the development of advanced biomaterials.

Implantable and Degradable Thermoplastic Elastomer

Biodegradable and implantable materials having elastomeric properties are highly desirable for many biomedical applications. Here, we report that poly(lactide)-co-poly(β-methyl-δ-valerolactone)-co-poly(lactide) (PLA-PβMδVL-PLA), a thermoplastic triblock poly(α-ester), has combined favorable properties of elasticity, biodegradability, and biocompatibility. This material exhibits excellent elastomeric properties in both dry and aqueous environments. The elongation at break is approximately 1000%, and stretched specimens completely recover to their original shape after force is removed. The material is degradable both in vitro and in vivo; it degrades more slowly than poly(glycerol sebacate) and more rapidly than poly(caprolactone) in vivo. Both the polymer and its degradation product show high cytocompatibility in vitro. The histopathological analysis of PLA-PβMδVL-PLA specimens implanted in the gluteal muscle of rats for 1, 4, and 8 weeks revealed similar tissue responses as compared with poly(glycerol sebacate) and poly(caprolactone) controls, two widely accepted implantable polymers, suggesting that PLA-PβMδVL-PLA can potentially be used as an implantable material with favorable in vivo biocompatibility. The thermoplastic nature allows this elastomer to be readily processed, as demonstrated by the facile fabrication of the substrates with topographical cues to enhance muscle cell alignment. These properties collectively make this polymer potentially highly valuable for applications such as medical devices and tissue engineering scaffolds.

Introducing a flexible drug delivery system based on poly(glycerol sebacate)-urethane and its nanocomposite: potential application in the prevention and treatment of oral diseases

In this study, a novel biopolymer based on poly(glycerol sebacic)-urethane (PGS-U) and its nanocomposites containing Cloisite@30B were synthesized by facile approach in which the crosslinking was created by aliphatic hexamethylene diisocyanate (HDI) at room temperature and 80 °C. Moreover, metronidazole and tetracycline drugs were selected as target drugs and loaded into PGSU based nanocomposites. A uniform and continuous microstructure with smooth surface is observed in the case of pristine PGS-U sample. The continuity of microstructure is observed in the case of all bionanocomposites. XRD result confirmed an intercalated morphology for PGSU containing 5 wt% of clay nanoparticles with a d-spacing 3.4 nm. The increment of nanoclay content up to 5%, the ultimate tensile stress and elastic modulus were obtained nearly 0.32 and 0.83 MPa, which the latter was more than eight-fold than that of pristine PGS-U. A sustained release for both dugs was observed by 200 h. The slowest and controlled drug release rate was determined in the case of PGSU containing 5 wt% clay and cured at 80 °C. A non-Fickian diffusion can be concluded in the case of tetracycline release via PGS-U/nanoclay bionanocomposites, while a Fickian process was detected in the case of metronidazole release by PGS-U/nanoclay bionanocomposites. As a result, the designed scaffold showed high flexibility, which makes it an appropriate option for utilization in the treatment of periodontal disease.

Fast photocurable thiol-ene elastomers with tunable biodegradability, mechanical and surface properties enhance myoblast differentiation and contractile function

Biodegradable elastomers are important emerging biomaterials for biomedical applications, particularly in the area of soft-tissue engineering in which scaffolds need to match the physicochemical properties of native tissues. Here, we report novel fast photocurable elastomers with readily tunable mechanical properties, surface wettability, and degradability. These elastomers are prepared by a 5-min UV-irradiation of thiol-ene reaction systems of glycerol tripentenoate (GTP; a triene) or the combination of GTP and 4-pentenyl 4-pentenoate (PP; a diene) with a carefully chosen series of di- or tri-thiols. In the subsequent application study, these elastomers were found to be capable of overcoming delamination of myotubes, a technical bottleneck limiting the in vitro growth of mature functional myofibers. The glycerol-based elastomers supported the proliferation of mouse and human myoblasts, as well as myogenic differentiation into contractile myotubes. More notably, while beating mouse myotubes detached from conventional tissue culture plates, they remain adherent on the elastomer surface. The results suggest that these elastomers as novel biomaterials may provide a promising platform for engineering functional soft tissues with potential applications in regenerative medicine or pharmacological testing.

Highly tough and ultrafast self-healable dual physically crosslinked sulfated alginate-based polyurethane elastomers for vascular tissue engineering

Since vascular diseases are regarded as a major cause of death worldwide, developing engineered biomimetic elastomers with physicochemical and biological properties resembling those of the natural vascular tissues, is vital for vascular tissue engineering (VTE). This study reports synthesis of highly tough supramolecular biologically active alginate-based supramolecular polyurethane (BASPU) elastomers that benefit from the presence of two physical networks with different strength of soft tertiary ammonium-soft sulfate pairs, as strong ionic bonds, and soft tertiary ammonium-hard carboxylate groups, as the weak bonds. The presence of sulfate groups resulted in low Young's modulus, high toughness and stretchability, proper energy dissipation, ultrafast self-healing and complete healing efficiency of BASPU. In vitro studies showed higher endothelial cells attachment, higher anticoagulation ability and significantly less platelet adhesion for BASPUs compared to the commercial vascular prosthesis. The histological studies of subcutaneously implanted scaffolds confirmed their low fibrosis and gradual biodegradation during 2 months of following.

Chitin nanocrystals assisted 3D printing of polycitrate thermoset bioelastomers

Citrate-based thermoset bioelastomer has numerous tissue engineering applications. However, its insoluble and unmeltable features restricted processing techniques for fabricating complex scaffolds. Herein, direct ink writing (DIW) was explored for 3D printing of poly(1, 8-octanediol-co-Pluronic F127 citrate) (POFC) bioelastomer scaffolds considering that POFC prepolymer (pre-POFC) was waterborne and could form a stable emulsion. The pre-POFC emulsion couldn't be printed, however, chitin nanocrystal (ChiNC) could be as a rheological modifier to tune the flow behavior of pre-POFC emulsion, and thus DIW printing of POFC scaffolds was successfully realized; moreover, ChiNC was also as a supporting agent to prevent collapse of filaments during thermocuring, and simultaneously as a biobased nanofiller to reinforce scaffolds. The rheological analyses showed the pre-POFC/ChiNC inks fulfilled the requirements for DIW printing. The printed scaffolds exhibited low swelling, and good performances in strength and resilence. Furthermore, the entire process was easily performed and eco-friendly.

Role of Curing Temperature of Poly(Glycerol Sebacate) Substrates on Protein-Cell Interaction and Early Cell Adhesion

A novel procedure to obtain smooth, continuous polymeric surfaces from poly(glycerol sebacate) (PGS) has been developed with the spin-coating technique. This method proves useful for separating the effect of the chemistry and morphology of the networks (that can be obtained by varying the synthesis parameters) on cell-protein-substrate interactions from that of structural variables. Solutions of the PGS pre-polymer can be spin-coated, to then be cured. Curing under variable temperatures has been shown to lead to PGS networks with different chemical properties and topographies, conditioning their use as a biomaterial. Particularly, higher synthesis temperatures yield denser networks with fewer polar terminal groups available on the surface. Material-protein interactions were characterised by using extracellular matrix proteins such as fibronectin (Fn) and collagen type I (Col I), to unveil the biological interface profile of PGS substrates. To that end, atomic force microscopy (AFM) images and quantification of protein adsorbed in single, sequential and competitive protein incubations were used. Results reveal that Fn is adsorbed in the form of clusters, while Col I forms a characteristic fibrillar network. Fn has an inhibitory effect when incubated prior to Col I. Human umbilical endothelial cells (HUVECs) were also cultured on PGS surfaces to reveal the effect of synthesis temperature on cell behaviour. To this effect, early focal adhesions (FAs) were analysed using immunofluorescence techniques. In light of the results, 130 °C seems to be the optimal curing temperature since a preliminary treatment with Col I or a Fn:Col I solution facilitates the formation of early focal adhesions and growth of HUVECs.

Bio-Based Thermo-Reversible Aliphatic Polycarbonate Network

Aliphatic polycarbonates represent an important class of materials with notable applications in the biomedical field. In this work, low Tg furan-functionalized bio-based aliphatic polycarbonates were cross-linked thanks to the Diels-Alder (DA) reaction with a bis-maleimide as the cross-linking agent. The thermo-reversible DA reaction allowed for the preparation of reversible cross-linked polycarbonate materials with tuneable properties as a function of the pendent furan content that was grafted on the polycarbonate backbone. The possibility to decrosslink the network around 70 °C could be an advantage for biomedical applications, despite the rather poor thermal stability of the furan-functionalized cross-linked polycarbonates.

Full biodegradable elastomeric nanocomposites fabricated by chitin nanocrystal and poly(caprolactone-diol citrate) elastomer

Chitin nanocrystal is a biocompatible and biodegradable nanofiller, with great potential in enhancing the mechanical and biological properties of polymers. Poly(caprolactone-diol citrate) is a kind of citrate-based biodegradable elastomer prepared by an additive-free melt polycondensation of polycaprolactone-diol and citric acid coupled with subsequent thermocuring. Here, a facile casting/evaporation method was utilized to prepare full biodegradable poly(caprolactone-diol citrate)/chitin nanocrystal nanocomposites, and their structure and properties were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, uniaxial tensile test, dynamic mechanical analysis, surface wettability and swelling analysis, thermogravimetric analysis, in vitro degradation, and cytocompatibility test. The results showed the chitin nanocrystals were uniformly distributed in the poly(caprolactone-diol citrate) matrix; with increasing chitin nanocrystal loading, the tensile modulus and strength significantly increased; furthermore, the incorporation of chitin nanocrystals endowed the poly(caprolactone-diol citrate) with more hydrophilicity, lower swelling in phosphate buffered saline solution, slow degradation rate, and greatly improved cytocompatibility. Thus, the chitin nanocrystal was a good bio-based nanofiller that could be used to tune the properties of poly(caprolactone-diol citrate) degradable bioelastomer.

One-Pot Synthesis of Unsaturated Polyester Bioelastomer with Controllable Material Curing for Microscale Designs

Synthetic polyester elastomeric constructs have become increasingly important for a range of healthcare applications, due to tunable soft elastic properties that mimic those of human tissues. A number of these constructs require intricate mechanical design to achieve a tunable material with controllable curing. Here, the synthesis and characterization of poly(itaconate-co-citrate-co-octanediol) (PICO) is presented, which exhibits tunable formation of elastomeric networks through radical crosslinking of itaconate in the polymer backbone of viscous polyester gels. Through variation of reaction times and monomer molar composition, materials with modulation of a wide range of elasticity (36-1476 kPa) are generated, indicating the tunability of materials to specific elastomeric constructs. This correlated with measured rapid and controllable gelation times. As a proof of principle, scaffold support for cardiac tissue patches is developed, which presents visible tissue organization and viability with appropriate elastomeric support from PICO materials. These formulations present potential application in a range of healthcare applications with requirement for elastomeric support with controllable, rapid gelation under mild conditions.

Versatile cross-linked fatty acid-based polycarbonate networks obtained by thiol–ene coupling reaction

Bio-sourced polycarbonate networks have been synthesized from an alkene-functional fatty-acid based polycarbonate precursor. Cross-linked networks were created using the radical thiol–ene coupling reaction. The resulting polycarbonate materials exhibited versatile properties either influenced by the structure of the cross-linker or the cross-linker/olefin unit ratio. Indeed, the storage modulus above the glass transition temperature could be modulated from 0.9 to 8.9 MPa only by changing the type of cross-linker, i.e. 1,9-nonanedithiol vs. 1,4-benzenedimethanethiol. The cross-linker/olefin unit ratio was also shown to largely impact the polycarbonate networks properties. An elongation at break of nearly 200% was reached when a low cross-linker/olefin ratio was applied. Moreover, functional polycarbonate networks bearing pendant thiol groups were obtained when an excess of dithiol was used with respect to olefin groups.

Bio-sourced polycarbonate networks have been synthesized from an alkene-functional fatty-acid based polycarbonate precursor.

Biodegradable Polymeric Materials in Degradable Electronic Devices

Biodegradable electronics have great potential to reduce the environmental footprint of devices and enable advanced health monitoring and therapeutic technologies. Complex biodegradable electronics require biodegradable substrates, insulators, conductors, and semiconductors, all of which comprise the fundamental building blocks of devices. This review will survey recent trends in the strategies used to fabricate biodegradable forms of each of these components. Polymers that can disintegrate without full chemical breakdown (type I), as well as those that can be recycled into monomeric and oligomeric building blocks (type II), will be discussed. Type I degradation is typically achieved with engineering and material science based strategies, whereas type II degradation often requires deliberate synthetic approaches. Notably, unconventional degradable linkages capable of maintaining long-range conjugation have been relatively unexplored, yet may enable fully biodegradable conductors and semiconductors with uncompromised electrical properties. While substantial progress has been made in developing degradable device components, the electrical and mechanical properties of these materials must be improved before fully degradable complex electronics can be realized.

Simple and Efficient Approach toward Photosensitive Biobased Aliphatic Polycarbonate Materials

Fatty acids were used as precursors for the synthesis of photosensitive polycarbonate materials. In order to avoid multistep reactions, a simple and straightforward methodology toward the synthesis of photosensitive monomers has been developed. Hence, a fatty acid-based cyclic carbonate bearing an unsaturation was synthesized and subsequently polymerized in a controlled manner (Đ = 1.07) by organo-catalyzed ring-opening polymerization (ROP). A thio-cinnamate derivative was then readily synthesized via a one-pot reaction and grafted onto the polycarbonate backbone by thiol-ene reaction. The content of photoresponsive cinnamoyl moiety grafted on the polycarbonate was tunable with the reaction time. Such functionalized polycarbonates could be crosslinked (by UV irradiation at 365 nm) and partially decrosslinked (irradiated at 254 nm) and exhibit versatile properties ranging from rather tough materials to elastomeric networks with respect to the content of the photosensitive cinnamoyl moiety grafted on the polymer.

Lysine-derived, pH-sensitive and biodegradable poly(beta-aminoester urethane) networks and their local drug delivery behaviour

In this study, a series of covalently crosslinked, l-lysine based poly(beta-aminoester urethane) (LPBAEU) networks with good biodegradability and pH sensitivity was reported. The effect of hydrophilic/hydrophobic characteristics and diacrylate/amine molar ratio on the structure, swelling and degradation behaviour of the networks was investigated. The water transport mechanism and dynamic swelling behavior of the LPBAEU networks were strongly affected by medium pH, and swelling amounts up to 252.2% and 148.7% were observed at pH 5.6 and pH 7.4, respectively. It was found that water diffusion within the networks followed a non-Fickian mechanism. The LPBAEU network with the highest diacrylate/amine molar ratio exhibited the highest tensile strength and Young's modulus. In vitro mass losses of networks showed that the degradation rate of LPBAEU networks can be adjusted from 4 to 14 days. LPBAEU networks also supported loading of doxycycline hyclate (DH) and in vitro release studies demonstrated that release of DH from the networks was substantially hindered in the neutral pH environment, with 20.9-56.2% DH release, whereas DH release was accelerated under mild acidic conditions, with a release percentage of 36.6-99.6%. The release data were fitted to different mathematical models and the obtained results confirmed that these networks released DH in a non-Fickian mechanism. The results of this research support the idea that pH-responsive LPBAEU networks may find potential applications in local drug delivery.

A tough and self-healing poly(l-glutamic acid)-based composite hydrogel for tissue engineering

Developing a tough, self-healing, and biodegradable composite hydrogel based on poly(l-glutamic acid) leads to great potential in tissue engineering applications.

Stereocomplexation, Thermal and Mechanical Properties of Conetworks Composed of Star-Shaped l-Lactide, d-Lactide and ε-Caprolactone Oligomers Utilizing Sugar Alcohols as Core Molecules

It is important to develop tailor-made biodegradable/biocompatible polymer networks usable for biomaterials whose thermal and mechanical properties are easily controlled by changing the composition. We synthesized sugar-alcohol-based polymer networks (SPN-mscLAO/3CLO, m = 4, 5 or 6) by the crosslinking reactions of erythritol, xylitol or sorbitol-based m-armed star-shaped l-lactide and d-lactide oligomers (HmSLLAO and HmSDLAO), a glycerol-based 3-armed star-shaped ε-caprolactone oligomer (H3SCLO) and hexamethylene diisocyanate (HDI) at the weight ratios of HmSLLAO/HmSDLAO = 1/1 and (HmSLLAO + HmSDLAO)/H3CLO = 100/0, 75/25, 50/50, 25/75 or 0/100). The influence of the arm number on the crystallization behavior, thermal and mechanical properties of SPN-mscLAO/3CLOs were systematically investigated by comparing with those of sugar-alcohol-based homochiral polymer network (SPN-mLLAO, m = 4, 5 or 6) prepared by the reaction of HmSLLAO and HDI. Stereocomplex (sc) crystallites are dominantly formed for SPN-mscLAO/3CLOs 100/0⁻25/75, whereas SPN-mLLAOs were amorphous. The higher order of melting temperature of sc-crystals for SPN-mscLAO/3CLOs 100/0⁻25/75 was m = 5 > m = 6 > m = 4. The sc-crystallinities of SPN-4scLAO/3CLOs 100/0⁻50/50 were significantly lower than those of SPN-mscLAO/3CLOs 100/0⁻50/50 (m = 5 and 6). The larger order of the sc-spherulite size at crystallization temperature of 110 °C was m = 5 > m = 6 > m = 4 for SPN-mscLAO/3CLO 100/0. The size and number of sc-spherulites decreased with increasing crystallization temperature over the range of 110⁻140 °C and with increasing CLO fraction. Among all the networks, SPN-5scLAO/3CLOs 75/25 and 50/50 exhibited the highest and second highest tensile toughnesses (21.4 and 20.3 MJ·m-3), respectively.

Biodegradable and biomimetic elastomeric scaffolds for tissue-engineered heart valves

Valvular heart diseases are the third leading cause of cardiovascular disease, resulting in more than 25,000 deaths annually in the United States. Heart valve tissue engineering (HVTE) has emerged as a putative treatment strategy such that the designed construct would ideally withstand native dynamic mechanical environment, guide regeneration of the diseased tissue and more importantly, have the ability to grow with the patient. These desired functions could be achieved by biomimetic design of tissue-engineered constructs that recapitulate in vivo heart valve microenvironment with biomimetic architecture, optimal mechanical properties and possess suitable biodegradability and biocompatibility. Synthetic biodegradable elastomers have gained interest in HVTE due to their excellent mechanical compliance, controllable chemical structure and tunable degradability. This review focuses on the state-of-art strategies to engineer biomimetic elastomeric scaffolds for HVTE. We first discuss the various types of biodegradable synthetic elastomers and their key properties. We then highlight tissue engineering approaches to recreate some of the features in the heart valve microenvironment such as anisotropic and hierarchical tri-layered architecture, mechanical anisotropy and biocompatibility.

STATEMENT OF SIGNIFICANCE

Heart valve tissue engineering (HVTE) is of special significance to overcome the drawbacks of current valve replacements. Although biodegradable synthetic elastomers have emerged as promising materials for HVTE, a mature HVTE construct made from synthetic elastomers for clinical use remains to be developed. Hence, this review summarized various types of biodegradable synthetic elastomers and their key properties. The major focus that distinguishes this review from the current literature is the thorough discussion on the key features of native valve microenvironments and various up-and-coming approaches to engineer synthetic elastomers to recreate these features such as anisotropic tri-layered architecture, mechanical anisotropy, biodegradability and biocompatibility. This review is envisioned to inspire and instruct the design of functional HVTE constructs and facilitate their clinical translation.

A highly stretchable bioelastomer prepared by UV curing of liquid-like poly(4-methyl-ε-caprolactone) precursors

UV curing of PMCL precursors in the absence of any solvent or heating led to highly stretchable bioelastomers.

A comparative study of the mechanical, shape-memory, and degradation properties of poly(lactic acid) nanofiber and cellulose nanocrystal reinforced poly(mannitol sebacate) nanocomposites

Composites based on elastomeric matrices and with enhanced mechanical behaviour at physiological temperatures useful for shape memory biodegradable implantable devices.

Biodegradable star-shaped polycyclic ester elastomers: Preparation, degradability, protein release, and biocompatibility in vitro

Effective local delivery methods for sustained and stable release of protein drugs are urgently needed. Biodegradable elastomers based on star-shaped polycyclic esters have received attention for their drug-loading and drug-release kinetics. However, the long degradation periods resulting from their strong lipophilicity greatly hinder their application. In this study, we synthesized new cross-linked elastomers based on methyl-acrylic-star-poly(ϵ-caprolactone- co-d,l-lactide) cyclic ester and methyl-bi-acrylic-poly(ϵ-caprolactone-b-poly(ethylene glycol)-b-ϵ-caprolactone) with different molecular weights; determined their physical, thermal, and morphological characteristics; and studied their in vitro degradation and release of bovine serum albumin and recombinant human interleukin 2. Elastomer hydrophilicity improved with the introduction of methyl-bi-acrylic-poly(ϵ-caprolactone-b-poly(ethylene glycol)-b-ϵ-caprolactone), and a shorter degradation period (~25 weeks) was achieved. Additionally, the degradation rate could be adjusted by varying the composition of methyl-bi-acrylic-poly(ϵ-caprolactone-b-poly(ethylene glycol)-b-ϵ-caprolactone) to directly influence the degree of swelling, cross-linking density, and sol content of the elastomer. The controlled rate of bovine serum albumin and recombinant human interleukin 2 release increased with a larger degree of swelling, higher sol content, and lower cross-link density of the elastomers. 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide analysis showed good biocompatibility. These results suggest that these new elastomers are potential candidates for carrier materials in controlled, implantable delivery systems for protein drugs and other biomedical applications.

Tough biodegradable mixed-macromer networks and hydrogels by photo-crosslinking in solution

The preparation of polymeric networks that are both tough and biodegradable remains a challenge. Here we show a very straightforward method to produce tough biodegradable networks from low molecular weight macromers for applications such as tissue engineering. Photo-crosslinking combinatorial mixtures of methacrylate-functionalized poly(1,3-trimethylene carbonate) (PTMC), poly(d,l-lactide) (PDLLA), poly(ε-caprolactone) (PCL) and poly(ethylene glycol) (PEG) oligomers in propylene carbonate (PC) allowed the preparation of network films with excellent tensile characteristics and resistance to tearing. This method enabled the production of both very tough mixed-macromer elastomers as well as mixed-macromer hydrogels. A mixed-macromer hydrogel prepared from 33wt.% PTMC, 33wt.% PCL and 33wt.% PEG had a very high tearing energy of 0.81kJ/m(2), which is comparable to tearing energies determined for articular cartilage.

Polyol-based biodegradable polyesters: a short review

Catalyst-free thermal polyesterification has recently emerged as a potential strategy for designing biodegradable thermoset polymers, particularly polyol-based polyesters for biomedical applications. These thermoset polyesters are synthesized through polycondensation of polyol and polyacid without the presence of catalyst or solvents. The mechanical properties, degradation rates, crystallinity, hydrophilicity, and biocompatibility can be controlled by adjusting the monomer feed ratios and curing conditions. These polyesters often degrade via surface erosion that allows the polymers to maintain structural integrity throughout hydrolysis. Additionally, polyol-based polyesters demonstrated good biocompatibility as non-toxic catalysts and/or solvents involved in the reaction, and the monomers used are endogenous to human metabolism which can be resorbed and metabolized in various physiological pathways. This review summarizes the polyol-based biodegradable polyesters that were synthesized by catalyst-free polyesterification.

Localized delivery and enhanced osteogenic differentiation with biodegradable galactitol polyester elastomers

Cytocompatible galactitol based polyesters showed variations in physical properties, degradation, dye release and ability to direct cells towards bone lineage.

Synthesis and characterization of poly(glycerol sebacate)-based elastomeric copolyesters for tissue engineering applications

A poly(glycerol sebacate)-based elastomeric copolyesters with improved mechanical properties and higher water uptake capacity.

Barrier properties of nano silicon carbide designed chitosan nanocomposites

Nano silicon carbide (SiC) designed chitosan nanocomposites were prepared by solution technique. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) were used for studying structural interaction of nano silicon carbide (SiC) with chitosan. The morphology of chitosan/SiC nanocomposites was investigated by field emission scanning electron microscope (FESEM), and high resolution transmission electron microscope (HRTEM). The thermal stability of chitosan was substantially increased due to incorporation of stable silicon carbide nanopowder. The oxygen permeability of chitosan/SiC nanocomposites was reduced by three folds as compared to the virgin chitosan. The chemical resistance properties of chitosan were enhanced due to the incorporation of nano SiC. The biodegradability was investigated using sludge water. The tensile strength of chitosan/SiC nanocomposites was increased with increasing percentage of SiC. The substantial reduction in oxygen barrier properties in combination with increased thermal stability, tensile strength and chemical resistance properties; the synthesized nanocomposite may be suitable for packaging applications.