Schottky Diode Leakage Current Fluctuations: Electrostatically Induced Flexoelectricity in Silicon

Nearly four decades have passed since IBM scientists pioneered atomic force microscopy (AFM) by merging the principles of a scanning tunneling microscope with the features of a stylus profilometer. Today, electrical AFM modes are an indispensable asset within the semiconductor and nanotechnology industries, enabling the characterization and manipulation of electrical properties at the nanoscale. However, electrical AFM measurements suffer from reproducibility issues caused, for example, by surface contaminations, Joule heating, and hard-to-minimize tip drift and tilt. Using as experimental system nanoscale Schottky diodes assembled on oxide-free silicon crystals of precisely defined surface chemistry, it is revealed that voltage-dependent adhesion forces lead to significant rotation of the AFM platinum tip. The electrostatics-driven tip rotation causes a strain gradient on the silicon surface, which induces a flexoelectric reverse bias term. This directional flexoelectric internal-bias term adds to the external (instrumental) bias, causing both an increased diode leakage as well as a shift of the diode knee voltage to larger forward biases. These findings will aid the design and characterization of silicon-based devices, especially those that are deliberately operated under large strain or shear, such as in emerging energy harvesting technologies including Schottky-based triboelectric nanogenerators (TENGs).

Solid-State Surface-Anchoring Strategy to Prepare Anti-Sintering Supported Metal Cluster Catalysts

Due to the unique geometric and electronic structures, supported metal clusters with sizes below 3 nm have appealed to great interest in heterogeneous catalysis. However, these supported ultrasmall metal clusters would endure severe particle coalescences under high reaction temperatures. Herein, based on the technology of ball-milling processing, we propose a solid-state "surface-anchoring" strategy to synthesize thermally stabilized Al2O3-supported Ni nanoclusters. Interestingly, when the theoretical Ni loading weight was 1 wt %, highly dispersed Ni species were found where no Ni nanoparticles would be seen after 500 °C calcination. Until the Ni loading weight increased to 5 wt % and the calcination temperature increased to 750 °C, the Ni nanoparticles became significant but still with a size of only about 6.8 nm. With the small Ni nanoparticles, the final 5-Ni-Al2O3-OAm-750 sample worked well as methane dry reforming catalysts with excellent anticoking performance during a 500 h stability test.

Porous silicon-based sensing and delivery platforms for wound management applications

Wound management remains a great challenge for clinicians due to the complex physiological process of wound healing. Porous silicon (PSi) with controlled pore morphology, abundant surface chemistry, unique photonic properties, good biocompatibility, easy biodegradation and potential bioactivity represent an exciting class of materials for various biomedical applications. In this review, we focus on the recent progress of PSi in the design of advanced sensing and delivery systems for wound management applications. Firstly, we comprehensively introduce the common type, normal healing process, delaying factors and therapeutic drugs of wound healing. Subsequently, the typical fabrication, functionalization and key characteristics of PSi have been summarized because they provide the basis for further use as biosensing and delivery materials in wound management. Depending on these properties, the rise of PSi materials is evidenced by the examples in literature in recent years, which has emphasized the robust potential of PSi for wound monitoring, treatment and theranostics. Finally, challenges and opportunities for the future development of PSi-based sensors and delivery systems for wound management applications are proposed and summarized. We hope that this review will help readers to better understand current achievements and future prospects on PSi-based sensing and delivery systems for advanced wound management.

Galinstan Liquid Metal Electrical Contacts for Monolayer-Modified Silicon Surfaces

Galinstan is the brand name for a low-melting gallium-based alloy, which is a promising nontoxic alternative to mercury, the only elemental metal found in the liquid state at room temperature. Liquid alloys such as Galinstan have found applications as electromechanical actuators, sensors, and soft contacts for molecular electronics. In this work, we validate the scope of Galinstan top contacts to probe the electrical characteristics of Schottky junctions made on Si(111) and Si(211) crystals modified with Si-C-bound organic monolayers. We show that the surface-to-volume ratio of the Galinstan drop used as a macroscopic contact defines the junction stability. Further, we explore chemical strategies to increase Galinstan surface tension to obtain control over the junction area, hence improving the repeatability and reproducibility of current-voltage (I-V) measurements. We explore Galinstan top contacts as a means to monitor changes in rectification ratios caused by surface reactions and use these data, most notably the static junction leakage, toward making qualitative predictions on the DC outputs recorded when these semiconductor systems are incorporated in Schottky-based triboelectric nanogenerators. We found that the introduction of iron particles leads to poor data repeatability for capacitance-voltage (C-V) measurements but has only a small negative impact in a dynamic current measurement (I-V).

Recent Advances in Field Effect Transistor Biosensors: Designing Strategies and Applications for Sensitive Assay

In comparison with traditional clinical diagnosis methods, field-effect transistor (FET)-based biosensors have the advantages of fast response, easy miniaturization and integration for high-throughput screening, which demonstrates their great technical potential in the biomarker detection platform. This mini review mainly summarizes recent advances in FET biosensors. Firstly, the review gives an overview of the design strategies of biosensors for sensitive assay, including the structures of devices, functionalization methods and semiconductor materials used. Having established this background, the review then focuses on the following aspects: immunoassay based on a single biosensor for disease diagnosis; the efficient integration of FET biosensors into a large-area array, where multiplexing provides valuable insights for high-throughput testing options; and the integration of FET biosensors into microfluidics, which contributes to the rapid development of lab-on-chip (LOC) sensing platforms and the integration of biosensors with other types of sensors for multifunctional applications. Finally, we summarize the long-term prospects for the commercialization of FET sensing systems.

Porous silicon surface modification via a microwave-induced in situ cyclic disulfide (S-S) cleavage and Si-S bond formation

Porous silicon (pSi) materials have gained a great deal of attention from various research fields, and their surface-functionalization is one of the critical points for their applications. In this study, a new surface modification method of Si-H-terminated pSi materials via microwave-induced Si-S bond formation is disclosed. The silicon hydride (Si-H) functionality on the pSi surface could react with the 5-membered cyclic disulfide (S-S) compound (DL-α-lipoic acid in this study) by microwave-induced in situ S-S bond cleavage and Si-S bond formation. This surface chemistry is fast responsive (<10 min) and more efficient than other methods such as vortexing, heating stirring, or ultrasonication. The reaction maintains the primary porous structure of pSi materials including pSi wafer, pSi rugate filer, and pSi nanoparticles. An additional functional group such as carboxylic acid is demonstrated to be readily introducible on the pSi surface for further applications. Overall, this study has successfully demonstrated the porous silicon surface modification via a microwave-induced in situ cyclic disulfide (S-S) cleavage and Si-S bond formation.

Hosseini I, Lu Y, Yedire SG, Mahshid SS, Tabatabaiefar MA, Liang C, Mahshid S. A Versatile Biomimic Nanotemplating Fluidic Assay for Multiplex Quantitative Monitoring of Viral Respiratory Infections and Immune Responses in Saliva and Blood

The last pandemic exposed critical gaps in monitoring and mitigating the spread of viral respiratory infections at the point-of-need. A cost-effective multiplexed fluidic device (NFluidEX), as a home-test kit analogous to a glucometer, that uses saliva and blood for parallel quantitative detection of viral infection and body's immune response in an automated manner within 11 min is proposed. The technology integrates a versatile biomimetic receptor based on molecularly imprinted polymers in a core-shell structure with nano gold electrodes, a multiplexed fluidic-impedimetric readout, built-in saliva collection/preparation, and smartphone-enabled data acquisition and interpretation. NFluidEX is validated with Influenza A H1N1 and SARS-CoV-2 (original strain and variants of concern), and achieves low detection limit in saliva and blood for the viral proteins and the anti-receptor binding domain (RBD) Immunoglobulin G (IgG) and Immunoglobulin M (IgM), respectively. It is demonstrated that nanoprotrusions of gold electrodes are essential for the fine templating of antibodies and spike proteins during molecular imprinting, and differentiation of IgG and IgM in whole blood. In the clinical setting, NFluidEX achieves 100% sensitivity and 100% specificity by testing 44 COVID-positive and 25 COVID-negative saliva and blood samples on par with the real-time quantitative polymerase chain reaction (p < 0.001, 95% confidence) and the enzyme-linked immunosorbent assay.

Advances of Various Heterogeneous Structure Types in Molecular Junction Systems and Their Charge Transport Properties

Molecular electronics that can produce functional electronic circuits using a single molecule or molecular ensemble remains an attractive research field because it not only represents an essential step toward realizing ultimate electronic device scaling but may also expand our understanding of the intrinsic quantum transports at the molecular level. Recently, in order to overcome the difficulties inherent in the conventional approach to studying molecular electronics and developing functional device applications, this field has attempted to diversify the electrical characteristics and device architectures using various types of heterogeneous structures in molecular junctions. This review summarizes recent efforts devoted to functional devices with molecular heterostructures. Diverse molecules and materials can be combined and incorporated in such two- and three-terminal heterojunction structures, to achieve desirable electronic functionalities. The heterojunction structures, charge transport mechanisms, and possible strategies for implementing electronic functions using various hetero unit materials are presented sequentially. In addition, the applicability and merits of molecular heterojunction structures, as well as the anticipated challenges associated with their implementation in device applications are discussed and summarized. This review will contribute to a deeper understanding of charge transport through molecular heterojunction, and it may pave the way toward desirable electronic functionalities in molecular electronics applications.

Modulating the Conduction Band Energies of Si Electrode Interfaces Functionalized with Monolayers of a Bay-Substituted Perylene Bisimide

The confinement of π-conjugated chromophores on silicon (Si) electrode surfaces is a powerful approach to engineer electroresponsive monolayers relevant to microelectronics, electrocatalysis, and information storage and processing. While common strategies to functionalize Si interfaces exploit molecularly dissolved building blocks, only a handful number of studies have leveraged the structure-function relationships of π-aggregates to tune the electronic structures of hybrid monolayers at Si interfaces. Herein, we show that the semiconducting properties of n-type monolayers constructed on Si electrodes are intimately correlated to the initial aggregation state of π-conjugated chromophore precursors derived from bay-substituted perylene bisimide (PBI) units. Specifically, our study unravels that for n-type monolayers engineered using PBI π-aggregates, the cathodic reduction potentials required to inject negative charge carriers into the conduction bands can be stabilized by 295 mV through reversible switching of the maximum anodic potential (MAP) that is applied during the oxidative cycles (+0.5 or +1.5 V vs Ag/AgCl). This redox-assisted stabilization effect is not observed with n-type monolayers derived from molecularly dissolved PBI cores and monolayers featuring a low surface density of the redox-active probes. These findings unequivocally point to the crucial role played by PBI π-aggregates in modulating the conduction band energies of n-type monolayers where a high MAP of +1.5 V enables the formation of electronic trap states that facilitate electron injection when sweeping back to cathodic potentials. Because the structure-function relationships of PBI π-aggregates are shown to modulate the semiconducting properties of hybrid n-type monolayers constructed at Si interfaces, our results hold promising opportunities to develop redox-switchable monolayers for engineering nonvolatile electronic memory devices.

Organic building blocks at inorganic nanomaterial interfaces

This tutorial review presents our perspective on designing organic molecules for the functionalization of inorganic nanomaterial surfaces, through the model of an "anchor-functionality" paradigm. This "anchor-functionality" paradigm is a streamlined design strategy developed from a comprehensive range of materials (e.g., lead halide perovskites, II-VI semiconductors, III-V semiconductors, metal oxides, diamonds, carbon dots, silicon, etc.) and applications (e.g., light-emitting diodes, photovoltaics, lasers, photonic cavities, photocatalysis, fluorescence imaging, photo dynamic therapy, drug delivery, etc.). The structure of this organic interface modifier comprises two key components: anchor groups binding to inorganic surfaces and functional groups that optimize their performance in specific applications. To help readers better understand and utilize this approach, the roles of different anchor groups and different functional groups are discussed and explained through their interactions with inorganic materials and external environments.

Photoactive silicon surfaces functionalized with high-quality and redox-active platinum diimine complex monolayers

Platinum diimine complexes can covalently be grafted onto oxide-free, hydrogen-terminated silicon(111) surfaces into clean and high-quality monolayers. The so modified surfaces offer great prospects as photocathodes for solar-driven electrocatalysis.

Sonochemical Reaction of Bifunctional Molecules on Silicon (111) Hydride Surface

While the sonochemical grafting of molecules on silicon hydride surface to form stable Si-C bond via hydrosilylation has been previously described, the susceptibility towards nucleophilic functional groups during the sonochemical reaction process remains unclear. In this work, a competitive study between a well-established thermal reaction and sonochemical reaction of nucleophilic molecules (cyclopropylamine and 3-Butyn-1-ol) was performed on p-type silicon hydride (111) surfaces. The nature of surface grafting from these reactions was examined through contact angle measurements, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Cyclopropylamine, being a sensitive radical clock, did not experience any ring-opening events. This suggested that either the Si-H may not have undergone homolysis as reported previously under sonochemical reaction or that the interaction to the surface hydride via a lone-pair electron coordination bond was reversible during the process. On the other hand, silicon back-bond breakage and subsequent surface roughening were observed for 3-Butyn-1-ol at high-temperature grafting (≈150 °C). Interestingly, the sonochemical reaction did not produce appreciable topographical changes to surfaces at the nano scale and the further XPS analysis may suggest Si-C formation. This indicated that while a sonochemical reaction may be indifferent towards nucleophilic groups, the surface was more reactive towards unsaturated carbons. To the best of the author's knowledge, this is the first attempt at elucidating the underlying reactivity mechanisms of nucleophilic groups and unsaturated carbon bonds during sonochemical reaction of silicon hydride surfaces.

Developing Longer-Lived Single Molecule Junctions with a Functional Flexible Electrode

Creating single-molecule junctions with a long-lived lifetime at room temperature is an open challenge. Finding simple and efficient approaches to increase the durability of single-molecule junction is also of practical value in molecular electronics. Here it is shown that a flexible gold-coated nanopipette electrode can be utilized in scanning tunneling microscope (STM) break-junction measurements to efficiently enhance the stability of molecular junctions by comparing with the measurements using conventional solid gold probes. The stabilizing effect of the flexible electrode displays anchor group dependence, which increases with the binding energy between the anchor group and gold. An empirical model is proposed and shows that the flexible electrode could promote stable binding geometries at the gold-molecule interface and slow down the junction breakage caused by the external perturbations, thereby extending the junction lifetime. Finally, it is demonstrated for the first time that the internal conduit of the flexible STM tip can be utilized for the controlled molecule delivery and molecular junction formation.

Impermeable Graphene Oxide Protects Silicon from Oxidation

The presence of a natural silicon oxide (SiO_x) layer over the surface of silicon (Si) has been a roadblock for hybrid semiconductor and organic electronics technology. The presence of an insulating oxide layer is a limiting operational factor, which blocks charge transfer and therefore electrical signals for a range of applications. Etching the SiO_x layer by fluoride solutions leaves a reactive Si-H surface that is only stable for few hours before it starts reoxidizing under ambient conditions. Controlled passivation of silicon is also of key importance for improving Si photovoltaic efficiency. Here, we show that a thin layer of graphene oxide (GO_x) prevents Si surfaces from oxidation under ambient conditions for more than 30 days. In addition, we show that the protective GO_x layer can be modified with molecules enabling a functional surface that allows for further chemical conjugation or connections with upper electrodes, while preserving the underneath Si in a nonoxidized form. The GO_x layer can be switched electrochemically to reduced graphene oxide, allowing the development of a dynamic material for molecular electronics technologies. These findings demonstrate that 2D materials are alternatives to organic self-assembled monolayers that are typically used to protect and tune the properties of Si and open a realm of possibilities that combine Si and 2D materials technologies.

Functionalized Silicon Electrodes Toward Electrostatic Catalysis

Oriented external electric fields are now emerging as "smart effectors" of chemical changes. The key challenges in experimentally studying electrostatic catalysis are (i) controlling the orientation of fields along the reaction axis and (ii) finely adjusting the magnitudes of electrostatic stimuli. Surface models provide a versatile platform for addressing the direction of electric fields with respect to reactants and balancing the trade-off between the solubility of charged species and the intensity of electric fields. In this mini-review, we present the recent advances that have been investigated of the electrostatic effect on the chemical reaction on the monolayer-functionalized silicon surfaces. We mainly focus on elucidating the mediator/catalysis role of static electric fields induced from either solid/liquid electric double layers at electrode/electrolyte interfaces or space charges in the semiconductors, indicating the electrostatic aspects is of great significance in the semiconductor electrochemistry, redox electroactivity, and chemical bonding. Herein, the functionalization of silicon surfaces allows scientists to explore electrostatic catalysis from nanoscale to mesoscale; most importantly, it provides glimpses of the wide-ranging potentials of oriented electric fields for switching on/off the macroscale synthetic organic electrochemistry and living radical polymerization.

Solution Chemistry to Control Boron-Containing Monolayers on Silicon: Reactions of Boric Acid and 4-Fluorophenylboronic Acid with H- and Cl-terminated Si(100)

The reactions of boric acid and 4-fluorophenylboronic acid with H- and Cl-terminated Si(100) surfaces in solution were investigated. X-ray photoelectron spectroscopy (XPS) studies reveal that both molecules react preferentially with Cl-Si(100) and not with H-Si(100) at identical conditions. On Cl-Si(100), the reactions introduce boron onto the surface, forming a Si-O-B structure. The quantification of boron surface coverage demonstrates that the 4-fluorophenylboronic acid leads to ∼2.8 times higher boron coverage compared to that of boric acid on Cl-Si(100). Consistent with these observations, density functional theory studies show that the reaction of boric acid and 4-fluorophenylboronic acid is more favorable with the Cl- versus H-terminated surface and that on Cl-Si(100) the reaction with 4-fluorophenylboronic acid is ∼55.3 kJ/mol more thermodynamically favorable than the reaction with boric acid. The computational studies were also used to demonstrate the propensity of the overall approach to form high-coverage monolayers on these surfaces, with implications for selective-area boron-based monolayer doping.

Magneto-fluorescent nanocomposites: experimental and theoretical linkage for the optimization of magnetic hyperthermia

Magneto-fluorescent nanocomposites have been recognized as an emerging class of materials displaying great potential for improved magnetic hyperthermia assisted by optical imaging. In this study, we have designed a series of hybrid composites that consist of zinc doped Zn_xFe_3-xO₄ ferrites functionalized by polyethylene-glycol (PEG8000) and an orange-emitting platinum complex [Pt(phen)Cl₂]. Experimental and theoretical studies on the optimization of their magnetically-mediated heating properties were conducted. PEG was assembled around particles' surface by two different approaches; in situ and post-PEGylation. PEGylation ensured the optimal distance between the magnetic core and Pt(ii)-complex to maintain significant luminescence in the composite. The successful inclusion of the complex to the organic matrix was confirmed by a variety of spectroscopic techniques. A theoretical model was developed, based on linear response theory, in order to examine the composites' power losses dependence on their properties. Within this model, inter-particle interactions were quantified by inserting a mean dipolar energy term in the estimation of Néel relaxation time, and consequently, the size and concentration that maximize power loss were derived (20 nm and 4 mg mL^-1). Moreover, a decrease in the anisotropy of nanoparticles resulted in an increase in specific loss power values. Theoretical estimations are validated by experimental data when heating aqueous dispersions of composites in 24 kA m^-1, 765 kHz AMF for various values of concentration and size. Magnetic hyperthermia results showed that the theory-predicted values of optimum concentration and size delivered the maximum-specific loss power which was found equal to 545 W g^-1. By the present approach, a quantitative link between the particles' dipolar interactions and their heating properties is established, while opening new perspectives to nanotheranostic applications.

Spontaneous Grafting of OH-Terminated Molecules on Si−H Surfaces via Si–O–C Covalent Bonding

The surface functionalization of oxide-free hydrogen-terminated silicon (Si−H) enables predictably tuning its electronic properties, by incorporating tailored functionality for applications such as photovoltaics, biosensing and molecular electronics devices. Most of the available chemical functionalization approaches require an external radical initiator, such as UV light, heat or chemical reagents. Here, we report forming organic monolayers on Si–H surfaces using molecules comprising terminal alcohol (–OH) groups. Self-assembled monolayer (SAM) formation is spontaneous, requires no external stimuli–and yields Si–O–C covalently bound monolayers. The SAMs were characterized by X-ray photoelectron spectroscopy (XPS) to determine the chemical bonding, by X-ray reflectometry (XRR) to determine the monolayers thicknesses on the surface and by atomic force microscopy (AFM) to probe surface topography and surface roughness. The redox activity and the electrochemical properties of the SAMs were studied using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The availability and the ease of incorporating OH groups in organic molecules, makes this spontaneous grafting as a reliable method to attach molecules to Si surfaces in applications ranging from sensing to molecular electronics where incorporating radical initiator setups is not accessible.

Ultrasonic Generation of Thiyl Radicals: A General Method of Rapidly Connecting Molecules to a Range of Electrodes for Electrochemical and Molecular Electronics Applications

Herein, we report ultrasonic generation of thiyl radicals as a general method for functionalizing a range of surfaces with organic molecules. The method is simple, rapid, can be utilized at ambient conditions and involves sonicating a solution of disulfide molecules, homolytically cleaving S-S bonds and generating thiyl radicals that react with the surfaces by forming covalently bound monolayers. Full molecular coverages on conducting oxides (ITO), semiconductors (Si-H), and carbon (GC) electrode surfaces can be achieved within a time scale of 15-90 min. The suitability of this method to connect the same molecule to different electrodes enabled comparing the conductivity of single molecules and the electrochemical electron transfer kinetics of redox active monolayers as a function of the molecule-electrode contact. We demonstrate, using STM break-junction technique, single-molecule heterojunction comprising Au-molecule-ITO and Au-molecule-carbon circuits. We found that despite using the same molecule, the single-molecule conductivity of Au-molecule-carbon circuits is about an order of magnitude higher than that of Au-molecule-ITO circuits. The same trend was observed for electron transfer kinetics, measured using electrochemical impedance spectroscopy for ferrocene-terminated monolayers on carbon and ITO. This suggests that the interfacial bond between different electrodes and the same molecule can be used to tune the conductivity of single-molecule devices and to control the rate of charge transport in redox active monolayers, opening prospects for relating various types of interfacial charge-transfer rate processes.

Common Background Signals in Voltammograms of Crystalline Silicon Electrodes are Reversible Silica-Silicon Redox Chemistry at Highly Conductive Surface Sites

The electrochemical reduction of bulk silica, due to its high electrical resistance, is of limited viability, namely, requiring temperatures in excess of 850 °C. By means of electrochemical and electrical measurements in atomic force microscopy, we demonstrate that at a buried interface, where silica has grown on highly conductive Si(110) crystal facets, the silica-silicon conversion becomes reversible at room temperature and accessible within a narrow potential window. We conclude that parasitic signals commonly observed in voltammograms of silicon electrodes originate from silica-silicon redox chemistry. While these findings do not remove the requirement of high temperature toward bulk silica electrochemical reduction, they redefine for silicon the potential window free from parasitic signals and, as such, significantly restrict the conditions where electroanalytical methods can be applied to the study of silicon surface reactivity.

Leveraging the Assembly of a Rylene Dye to Tune the Semiconducting Properties of Functionalized n-Type, Hybrid Si Interfaces

The functionalization of silicon electrodes with π-conjugated chromophores opens new avenues to engineer hybrid semiconducting interfaces relevant to information storage and processing. Notably, molecularly dissolved π-conjugated units, such as ferrocene derivatives, are traditionally exploited as building blocks to construct well-defined interfaces that establish electrochemically addressable platforms with which to investigate electron transfer properties and charge storage capabilities. In contrast, planar π-conjugated building blocks such as naphthalene diimide (NDI) cores enable the formation of solvated aggregates equipped with emergent electronic structures not manifested by the parent, molecularly dissolved building blocks. To interrogate the extent to which the aggregated states of π-conjugated chromophores can be leveraged to regulate the n-type semiconducting properties of functionalized electrodes, we have devised an amphiphilic rylene core (NDI) that demonstrates a non-negligible degree of aggregation in an aqueous medium. Characterization of the electronic structures of the NDI-derived aggregates using a combination of electrochemistry, reductive titration experiments, and spectroelectrochemistry unveils the existence of π-anion stacks, the formation of which is contingent on the initial concentration of NDI building blocks. We show that grafting n-doped NDI aggregates on silicon electrode precursors equipped with a high density of anchoring groups by means of "click" reaction enables the formation of the hybrid Si-NDI electrode (Si-NDI-15@1) that facilitates electron injection by more than 400 mV when compared to Si interfaces constructed from molecularly dissolved NDI units. Furthermore, the engineering of a Si precursor surface characterized by a low density of anchoring groups provides additional proof to highlight that the potentiometric properties recorded for Si-NDI-15@1 originate from NDI units, evidencing a non-negligible degree of aggregation. The present work delivers tools to manipulate the potentiometric properties of functionalized electrodes by leveraging on the electronic structures of aggregated, π-conjugated precursors.

Stimulus-cleavable chemistry in the field of controlled drug delivery

This review comprehensively summarises stimulus-cleavable linkers from various research areas and their cleavage mechanisms, thus provides an insightful guideline to extend their potential applications to controlled drug release from nanomaterials.

Effect of Covalent Surface Functionalization of Si on the Activity of Trifluoromethanesulfonic Anhydride for Suppressing Surface Recombination

An examination of the efficacy of combining physisorbed and chemisorbed passivation strategies on crystalline Si has been performed. This report compares the influence of a linear alkyl adsorbate tethered by either a Si-C or Si-Si linkage, prepared by reaction of Si(111) with organometallic Grignard reagents or organosilanes, respectively. These modified surfaces are first analyzed and compared by IR and X-ray photoelectron spectroscopies. Their behavior toward a known potent physisorbate, trifluoromethanesulfonic anhydride (Tf₂O), is then examined. Microwave photoconductivity measurements were obtained which indicate that, while Tf₂O shows a beneficial lowering of surface recombination on both surface types initially, only surfaces featuring Si-C linkages exhibit long-lasting suppressed surface recombination. The data for Grignard-treated Si after exposure to Tf₂O in fact represent the longest known report of surface recombination suppression by a physisorbate. Conversely, the data for the Si surfaces prepared by dehydrogenative coupling suggest that these passivating groups themselves introduce defect states that cannot be ameliorated by Tf₂O physisorption.

Covalent Linkages of Molecules and Proteins to Si-H Surfaces Formed by Disulfide Reduction

Thiols and disulfide contacts have been, for decades, key for connecting organic molecules to surfaces and nanoclusters as they form self-assembled monolayers (SAMs) on metals such as gold (Au) under mild conditions. In contrast, they have not been similarly deployed on Si owing to the harsh conditions required for monolayer formation. Here, we show that SAMs can be simply formed by dipping Si-H surfaces into dilute solutions of organic molecules or proteins comprising disulfide bonds. We demonstrate that S-S bonds can be spontaneously reduced on Si-H, forming covalent Si-S bonds in the presence of traces of water, and that this grafting can be catalyzed by electrochemical potential. Cyclic disulfide can be spontaneously reduced to form complete monolayers in 1 h, and the reduction can be catalyzed electrochemically to form full surface coverages within 15 min. In contrast, the kinetics of SAM formation of the cyclic disulfide molecule on Au was found to be three-fold slower than that on Si. It is also demonstrated that dilute thiol solutions can form monolayers on Si-H following oxidation to disulfides under ambient conditions; the supply of too much oxygen, however, inhibits SAM formation. The electron transfer kinetics of the Si-S-enabled SAMs on Si-H is comparable to that on Au, suggesting that Si-S contacts are electrically transmissive. We further demonstrate the prospect of this spontaneous disulfide reduction by forming a monolayer of protein azurin on a Si-H surface within 1 h. The direct reduction of disulfides on Si electrodes presents new capabilities for a range of fields, including molecular electronics, for which highly conducting SAM-electrode contacts are necessary and for emerging fields such as biomolecular electronics as disulfide linkages could be exploited to wire proteins between Si electrodes, within the context of the current Si-based technologies.

Functionalized Silicon Electrodes in Electrochemistry

Avoiding the growth of SiO_x has been an enduring task for the use of silicon as an electrode material in dynamic electrochemistry. This is because electrochemical assays become unstable when the SiO_x levels change during measurements. Moreover, the silicon electrode can be completely passivated for electron transfer if a thick layer of insulating SiO_x grows on the surface. As such, the field of silicon electrochemistry was mainly developed by electron-transfer studies in nonaqueous electrolytes and by applications employing SiO_x-passivated silicon-electrodes where no DC currents are required to cross the electrode/electrolyte interface. A solution to this challenge began by functionalizing Si-H electrodes with monolayers based on Si-O-Si linkages. These monolayers have proven very efficient to avoid SiO_x formation but are not stable for a long-term operation in aqueous electrolytes due to hydrolysis. It was only with the development of self-assembled monolayers based on Si-C linkages that a reliable protection against SiO_x formation was achieved, particularly with monolayers based on α,ω-dialkynes. This review discusses in detail how this surface chemistry achieves such protection, the electron-transfer behavior of these monolayer-modified silicon surfaces, and the new opportunities for electrochemical applications in aqueous solution.

High-resolution light-activated electrochemistry on amorphous silicon-based photoelectrodes

Light-activated electrochemistry (LAE) consists of employing a focused light beam to illuminate a semiconducting area and make it electrochemically active. Here, we show how to reduce the electrochemical spatial resolution to submicron by exploiting the short lateral diffusion of charge carriers in amorphous silicon to improve the resolution of LAE by 60 times.

Diverse Surface Chemistry of Cobalt Ferrite Nanoparticles to Optimize Copper(II) Removal from Aqueous Media

Water pollution by heavy metals is one of the most serious worldwide environmental issues. With a focus on copper(II) ions and copper complex removal, in the present study, ultra-small primary CoFe₂O₄ magnetic nanoparticles (MNPs) coated with octadecylamine (ODA) of adequate magnetization were solvothermally prepared. The surface modification of the initial MNPs was adapted via three different chemical approaches based on amine and/or carboxylate functional groups: (i) the deposition of polyethylimide (PEI), (ii) covalent binding with diethylenetriaminepentaacetic acid (DTPA), and (iii) conjugation with both PEI and DTPA, respectively. FT-IR, TGA, and DLS measurements confirmed that PEI or/and DTPA were successfully functionalized. The percentage of the free amine (−NH₂) groups was also estimated. Increased magnetization values were found in case of PEI and DTPA-modified MNPs that stemmed from the adsorbed amine or oxygen ligands. Comparative UV–Vis studies for copper(II) ion removal from aqueous solutions were conducted, and the effect of time on the adsorption capacity was analyzed. The PEI-modified particles exhibited the highest adsorption capacity (164.2 mg/g) for copper(II) ions and followed the pseudo-second-order kinetics, while the polynuclear copper(II) complex Cu_x(DTPA)_y was also able to be immobilized. The nanoadsorbents were quickly isolated from the solution by magnetic separation and regenerated easily by acidic treatment.

Monolayers of an organosilane on magnetite nanoparticles for the fast removal of Cr(VI) from water

Monolayers of N-(2-aminoethyl)-3-aminopropyltrimethoxysilane have been established on magnetite nanoparticles to develop a novel magnetic adsorbent for fast decontamination of hexavalent chromium (Cr(VI)) from water. Results indicated that monolayer adsorption of the silane from water took place at low concentrations (<300 mg/L) and around 100% surface coverage was obtained at temperatures ≥90°C. The hydrolysed silane was anchored to the magnetite surface through condensation reactions between its silanol groups and the surface hydroxyl groups of magnetite. The functional amine groups were protonated by acid treatment for adsorbing Cr(VI). The monolayer of the silane on magnetite (MSM) with approximately 100% surface coverage showed extremely rapid adsorption kinetics for Cr(VI), such that the process was complete within 1 min. This enables the treatment of large amounts of sewage per unit time. The adsorption capacity for Cr(VI) was 8.0 mg/g, as estimated from the Langmuir isotherm model. The saturation magnetization of the MSM reached 64.16 emu/g, allowing easy magnetic recovery from water. In the presence of up to 50-fold molar excesses of chloride and nitrate anions, little effect on Cr(VI) removal was seen, but moderate and large impacts were observed with sulphate and hydroxyl anions, respectively. Desorption of adsorbed Cr(VI) and regeneration of the MSM were successfully achieved by NaOH and HCl treatments to deprotonate and protonate the amine groups, respectively. By selecting a silane with suitable functional groups, the surface properties may be tailored for a particular pollutant.

Exploiting the versatile alkyne-based chemistry for expanding the applications of a stable triphenylmethyl organic radical on surfaces

The incorporation of terminal alkynes into the chemical structure of persistent organic perchlorotriphenylmethyl (PTM) radicals provides new chemical tools to expand their potential applications. In this work, this is demonstrated by the chemical functionalization of two types of substrates, hydrogenated SiO₂-free silicon (Si-H) and gold, and, by exploiting the click chemistry, scarcely used with organic radicals, to synthesise multifunctional systems. On one hand, the one-step functionalization of Si-H allows a light-triggered capacitance switch to be successfully achieved under electrochemical conditions. On the other hand, the click reaction between the alkyne-terminated PTM radical and a ferrocene azide derivative, used here as a model azide system, leads to a multistate electrochemical switch. The successful post-surface modification makes the self-assembled monolayers reported here an appealing platform to synthesise multifunctional systems grafted on surfaces.

Metal-Single-Molecule-Semiconductor Junctions Formed by a Radical Reaction Bridging Gold and Silicon Electrodes

Here we report molecular films terminated with diazonium salts moieties at both ends which enables single-molecule contacts between gold and silicon electrodes at open circuit via a radical reaction. We show that the kinetics of film grafting is crystal-facet dependent, being more favorable on ⟨111⟩ than on ⟨100⟩, a finding that adds control over surface chemistry during the device fabrication. The impact of this spontaneous chemistry in single-molecule electronics is demonstrated using STM-break junction approaches by forming metal-single-molecule-semiconductor junctions between silicon and gold source and drain, electrodes. Au-C and Si-C molecule-electrode contacts result in single-molecule wires that are mechanically stable, with an average lifetime at room temperature of 1.1 s, which is 30-400% higher than that reported for conventional molecular junctions formed between gold electrodes using thiol and amine contact groups. The high stability enabled measuring current-voltage properties during the lifetime of the molecular junction. We show that current rectification, which is intrinsic to metal-semiconductor junctions, can be controlled when a single-molecule bridges the gap in the junction. The system changes from being a current rectifier in the absence of a molecular bridge to an ohmic contact when a single molecule is covalently bonded to both silicon and gold electrodes. This study paves the way for the merging of the fields of single-molecule and silicon electronics.

Structure of Mixed Acid/Decyl Monolayers Grafted on Oxide-Free Si(111) Surfaces

The structure of mixed acid/decyl monolayers (MLs) grafted on oxide-free Si(111) surfaces by photochemical hydrosilylation in a mixture of neat undecylenic acid and 1-decene is studied in detail. After appropriate surface cleaning of the as-grafted surfaces, atomic force microscopy (AFM) (topography and phase imaging) and calibrated FTIR analysis demonstrate that a mixed monolayer is formed, free of residue. When the acid-molecule fraction (Γ_SOL) is >0.1, mixed MLs are homogeneous on the scale of observations and they are only slightly enriched in acid chains with respect to the solution. Conversely, when Γ_SOL < 0.1, the acid chain fraction within the ML becomes quasi-independent of the solution composition and may become much larger than Γ_SOL. In addition, dark domains are observed in AFM phase images. Correlations between the characteristic parameters of νCO IR bands and AFM phase images suggest a strong phase separation of acid and alkyl chains at various length scales. A model involving a structuration of the grafting solution is proposed to explain observations.

Differential functionalisation of the internal and external surfaces of carbon-stabilised nanoporous silicon

A versatile strategy to differentiate the surface chemistry of the internal and external pore walls of highly-stable nanoporous silicon.

A Mini Review: Recent Advances in Surface Modification of Porous Silicon

Porous silicon has been utilized within a wide spectrum of industries, as well as being used in basic research for engineering and biomedical fields. Recently, surface modification methods have been constantly coming under the spotlight, mostly in regard to maximizing its purpose of use. Within this review, we will introduce porous silicon, the experimentation preparatory methods, the properties of the surface of porous silicon, and both more conventional as well as newly developed surface modification methods that have assisted in attempting to overcome the many drawbacks we see in the existing methods. The main aim of this review is to highlight and give useful insight into improving the properties of porous silicon, and create a focused description of the surface modification methods.

Functionalized Self-Assembled Monolayers Bearing Diiminate Complexes Immobilized through Covalently Anchored Ligands

The application of synthetic organic chemistry to the surface chemistry of monolayer arrays adds a novel dimension to the power of these systems for surface modification. This paper describes the elaboration of simple functionalized monolayers into dialdimine and dialdiminate ligands tethered to the monolayer surface. These ligands are then used to coordinate metal ions in an effort to form diiminate complexes with control over their environment and orientation. Ligand anchoring is best achieved through either thiol-ene photochemistry or azide-acetylene "click" chemistry. There is an influence of ligand bulk on some surface transformations, and in some cases reactions that have been reported to be effective on simple, homogeneous monolayer surfaces are not applicable to a more complex monolayer environment. The large excess of solution reagents relative to monolayer surface functionality adds another measure of difficulty to the control of interfacial reactions. In instances where the anchoring chain includes functional groups that can directly interact with metal ions, the metalation of ligand-bearing surfaces resulted in a higher metal ion content than would have been expected from binding only to the diimine ligands.

1,2-Epoxyalkane: Another Precursor for Fabricating Alkoxy Self-Assembled Monolayers on Hydrogen-Terminated Si(111)

This work describes the UV alkoxylation of a series of 1,2-epoxyalkanes on the hydrogen-terminated silicon (H-Si) substrate. The formation of alkoxy self-assembled monolayers (SAMs) and the nature of bonding at the surface of H-Si were examined using water contact angle goniometer, spectroscopic ellipsometer, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy. UV exposure to 1,2-epoxyalkane mesitylene solution for 60 min formed alkoxy-SAMs onto H-Si with hydrophobic properties. The local molecular environment of the alkyl chains transitioned from a disordered, liquid-like state to an ordered, crystalline-like structure with increasing the chain length. XPS and FTIR indicated that the reaction of H-Si with 1,2-epoxyalkane produced Si-O-C linkages. The Si-H bond homolysis and electron/hole were the plausible mechanistic routes for the grafting of 1,2-epoxyalkanes.

Point of Anchor: Impacts on Interfacial Charge Transfer of Metal Oxide Nanoparticles

Photoinduced charge transfer across the metal oxide-organic ligand interface plays a key role in the diverse applications of metal oxide nanomaterials/nanostructures, such as photovoltaics, photocatalysis, and optoelectronics. Thus far, most studies are focused on molecular engineering of the organic chromophores, where the charge-transfer properties have been found to dictate the photo absorption efficiency and eventual device performance. Yet, as the chromophores are mostly bound onto the metal oxide surfaces by hydroxyl or carboxyl anchors, the impacts of the bonding interactions at the metal oxide-ligand interface on interfacial charge transfer have remained largely unexplored. Herein, acetylene derivatives are demonstrated as effective surface capping ligands for metal oxide nanoparticles, as exemplified with TiO₂, RuO₂, and ZnO. Experimental studies and first-principles calculations suggest the formation of M-O-C≡C- core-ligand linkages that lead to effective interfacial charge delocalization, in contrast to hopping/tunneling by the conventional M-O-CO- interfacial bonds in the carboxyl-capped counterparts. This leads to the generation of an interfacial state within the oxide bandgap and much enhanced sensitization of the nanoparticle photoluminescence emissions as well as photocatalytic activity, as manifested in the comparative studies with TiO₂ nanoparticles functionalized with ethynylpyrene and pyrenecarboxylic acid. These results highlight the significance of the unique interfacial bonding chemistry by acetylene anchoring group in facilitating efficient charge transfer through the oxide-ligand interfacial linkage and hence the fundamental implication in their practical applications.

Maskless Spatioselective Functionalization of Silicon Nanowires

Spatioselective functionalization of silicon nanowires was achieved without using a masking material. The designed process combines metal-assisted chemical etching (MACE) to fabricate silicon nanowires and hydrosilylation to form molecular monolayers. After MACE, a monolayer was formed on the exposed nanowire surfaces. A second MACE step was expected to elongate the nanowires, thus creating two different segments. When monolayers of 1-undecene or 1-tetradecyne were formed on the upper segment, however, the second MACE step did not extend the nanowires. In contrast, nanowires functionalized with 1,8-nonadiyne were elongated, but at an approximately 8 times slower etching rate. The elongation resulted in a contrast difference in high-resolution scanning electron microscopy (HR-SEM) images, which indicated the formation of nanowires that were covered with a monolayer only at the top parts. Click chemistry was successfully used for secondary functionalization of the monolayer with azide-functionalized nanoparticles. The spatioselective presence of 1,8-nonadiyne gave a threefold higher particle density on the upper segment functionalized with 1,8-nonadiyne than on the lower segment without monolayer. These results indicate the successful spatioselective functionalization of silicon nanowires fabricated by MACE.

Switchable Interfaces: Redox Monolayers on Si(100) by Electrochemical Trapping of Alcohol Nucleophiles

Organic electrosynthesis is going through its renaissance but its scope in surface science as a tool to introduce specific molecular signatures at an electrode/electrolyte interface is under explored. Here, we have investigated an electrochemical approach to generate in situ surface-tethered and highly-reactive carbocations. We have covalently attached an alkoxyamine derivative on an Si(100) electrode and used an anodic bias stimulus to trigger its fragmentation into a diffusive nitroxide (TEMPO) and a surface-confined carbocation. As a proof-of-principle we have used this reactive intermediate to trap a nucleophile dissolved in the electrolyte. The nucleophile was ferrocenemethanol and its presence and surface concentration after its reaction with the carbocation were assessed by cyclic voltammetry. The work expands the repertoire of available electrosynthetic methods and could in principle lay the foundation for a new form of electrochemical lithography.

Design, Synthesis, and Isomerization Studies of Light-Driven Molecular Motors for Single Molecular Imaging

The design of a multicomponent system that aims at the direct visualization of a synthetic rotary motor at the single molecule level on surfaces is presented. The synthesis of two functional motors enabling photochemical rotation and fluorescent detection is described. The light-driven molecular motor is found to operate in the presence of a fluorescent tag if a rigid long rod (32 Å) is installed between both photoactive moieties. The photochemical isomerization and subsequent thermal helix inversion steps are confirmed by ¹H NMR and UV–vis absorption spectroscopies. In addition, the tetra-acid functioned motor can be successfully grafted onto amine-coated quartz and it is shown that the light responsive rotary motion on surfaces is preserved.

Vacuum Ultraviolet Treatment of Acid- and Ester-Terminated Self-Assembled Monolayers: Chemical Conversions and Friction Reduction

We have prepared COOH- and COOCH₃-terminated self-assembled monolayers (SAMs) from undec-10-enoic acid (UDA) and methyl undec-10-enoate (MUDO) molecules on hydrogen-terminated silicon (H-Si) substrates through ultraviolet (UV) irradiation. The as-prepared UDA- and MUDO-SAMs were exposed to 172 nm vacuum-UV (VUV) light in a high vacuum environment (HV, <10^-3 Pa) for different periods. The presence of COO components at the surfaces of these SAMs without prior oxidation would simplify the understanding of the origin of the chemical conversions and the changes of surface properties, as the prior oxidation would change the surface properties and generate different oxygenated groups. After the HV-VUV treatment, the abundance of COOH and COOCH₃ components of these SAMs decreased without significant dissociation of their C-C backbones. Degradation of these components occurred through dissociating their C-O bonds, resulting in different C═O components. Also, the occurrence of Norrish type pathways resulted in a slight decrease of carbon content and produced CH₃ components. We have applied the HV-VUV lithography to control the abundance of COOH and COOCH₃ components in well-defined areas and to investigate the friction differences between the irradiated and masked areas. The irradiated areas exhibited lower friction than the masked areas without observing significant height contrasts between these areas. The reduction in friction was attributed to the conversion of the COOH and COOCH₃ components to less adhesive components such as C═O and CH₃. These experiments suggest the HV-VUV treatments as an approach for low damage dry surface modifications and reductive lithographic techniques at surfaces terminated by acid and ester groups.

The critical role of wavelength in the UV-activated grafting of 1-alkene onto silicon and silicon nitride SixN4 surfaces

The wavelength used during photochemical grafting of alkene onto silicon related surfaces influences molecular surface coverage.

Reproducible flaws unveil electrostatic aspects of semiconductor electrochemistry

Predicting or manipulating charge-transfer at semiconductor interfaces, from molecular electronics to energy conversion, relies on knowledge generated from a kinetic analysis of the electrode process, as provided by cyclic voltammetry. Scientists and engineers encountering non-ideal shapes and positions in voltammograms are inclined to reject these as flaws. Here we show that non-idealities of redox probes confined at silicon electrodes, namely full width at half maximum <90.6 mV and anti-thermodynamic inverted peak positions, can be reproduced and are not flawed data. These are the manifestation of electrostatic interactions between dynamic molecular charges and the semiconductor’s space-charge barrier. We highlight the interplay between dynamic charges and semiconductor by developing a model to decouple effects on barrier from changes to activities of surface-bound molecules. These findings have immediate general implications for a correct kinetic analysis of charge-transfer at semiconductors as well as aiding the study of electrostatics on chemical reactivity.

Most electrical devices must pass charges across semiconductor interfaces, yet redox-active molecular behavior obscures comprehension of these processes. Here, the authors develop a model to describe redox processes on semiconductor surfaces and gauge these interactions electrochemically.