Temperature Sensing Properties of Biocompatible Yb/Er-Doped GdF3 and YF3 Mesocrystals

Y0.8-xGdxF3:Yb/Er mesocrystals with a biocompatible surface and diverse morphological characteristics were successfully synthesized using chitosan-assisted solvothermal processing. Their structural properties, studied using X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning and transmission electron microscopy and energy dispersive X-ray analysis, were further correlated with the up-conversion emission (λexc = 976 nm) recorded in function of temperature. Based on the change in the visible green emissions originating from the thermally coupled 2H11/2 and 4S3/2 levels of Er3+, the corresponding LIR was acquired in the physiologically relevant range of temperatures (25-50 °C). The detected absolute sensitivity of about 0.0042 °C-1, along with the low cytotoxicity toward both normal human lung fibroblasts (MRC-5) and cancerous lung epithelial (A549) cells, indicate a potential for use in temperature sensing in biomedicine. Additionally, their enhanced internalization in cells, without suppression of cell viability, enabled in vitro labeling of cancer and healthy cells upon 976 nm laser irradiation.

Development of an Fe2+ sensing system based on the inner filter effect between upconverting nanoparticles and ferrozine

The ferrozine (FZ) assay is a vital oxidation state-specific colorimetric assay for the quantification of Fe2+ ions in environmental samples due to its sharp increase in absorbance at 562 nm upon addition of Fe2+. However, it has yet to be applied to corresponding fluoresence assays which typically offer higher sensitivites and lower detection limits. In this article we present for the first time its pairing with upconverting luminescent nanomaterials to enable detection of Fe2+via the inner filter effect using a low-power continuous wave diode laser (45 mW). Upon near infra-red excitation at 980 nm, the overlap of the upconversion emission of Er3+ at approximately 545 nm and the absorbance of the FZ:Fe2+ complex at 562 nm enabled measurement in the change of UCNP emission response as a function of Fe2+ concentration in a ratiometric manner. We first applied large, ultra-bright poly(acrylic acid) (PAA)-capped Gd2O2S:Yb3+,Er3+ UCNPs upconverting nanoparticles (UCNPs) for the detection of Fe2+ using FZ as the acceptor. The probe displayed good selectivity and sensitivity for Fe2+, with a low limit of detection (LoD) of 2.74 μM. Analogous results employing smaller (31 nm) PAA-capped hexagonal-phase NaYF4:Yb3+,Er3+ UCNPs synthesised in our lab were achieved, with a lower LoD towards Fe2+ of 1.43 μM. These results illustrate how the ratiometric nature of the system means it is applicable over a range of particle sizes, brightnesses and nanoparticle host matrices. Preliminary investigations also found the probes capable of detecting micromolar concentrations of Fe2+ in turbid solutions.

Intraoperative diagnosis of early lymphatic metastasis using neodymium-based rare-earth NIR-II fluorescence nanoprobe

The high mortality of breast cancer is closely related to lymph node (LN) metastasis. Sentinel LNs (SLNs) are the first station where tumor cells metastasize through the lymphatic system. As such, achieving precise diagnosis of the early metastatic status of SLNs during surgery is of paramount importance for precision therapy of breast cancer. While invasive SLNs biopsy is the gold standard for evaluating the status of SLNs, its use is often time-consuming and may increase the risk of operation. It is still challenging to develop a means for rapid SLN metastasis diagnosis. Herein, NaGdF4:5%Nd@NaLuF4 rare earth nanoparticles (Gd:Nd-RENPs) with near-infrared-II (NIR-II) fluorescence and magnetic resonance imaging (MRI) properties were fabricated. With the nanoprobe, metastatic SLNs and lymph vessels (LVs) rapidly brighten and can be observed by the NIR-II imaging system, which is totally different from normal LNs and LVs. The remarkable contrast observed via NIR-II imaging serves to swiftly delineate metastatic SLNs from normal ones, subsequently guiding precise surgical resection of metastatic LNs in just 10 minutes. Furthermore, the consistency between the results obtained via MRI and NIR-II imaging further validates the dependability of this nanoprobe as a diagnostic tool for metastatic SLNs. Additionally, the Gd:Nd-RENPs exhibited good biocompatibility in vitro and in vivo. In this study, we demonstrated the advantages and prospects of NIR-II imaging for intraoperative early SLN metastasis assessment and shed light on the potential of the dual-modal Gd:Nd-RENPs as a nanoprobe.

Recent advances in lanthanide-doped up-conversion probes for theranostics

Up-conversion (or anti-Stokes) luminescence refers to the phenomenon whereby materials emit high energy, short-wavelength light upon excitation at longer wavelengths. Lanthanide-doped up-conversion nanoparticles (Ln-UCNPs) are widely used in biomedicine due to their excellent physical and chemical properties such as high penetration depth, low damage threshold and light conversion ability. Here, the latest developments in the synthesis and application of Ln-UCNPs are reviewed. First, methods used to synthesize Ln-UCNPs are introduced, and four strategies for enhancing up-conversion luminescence are analyzed, followed by an overview of the applications in phototherapy, bioimaging and biosensing. Finally, the challenges and future prospects of Ln-UCNPs are summarized.

Size effect of DyF3 nanoparticles on Curie temperature

A series of DyF₃ nanoparticles samples were synthesized by a hydrothermal treatment in an autoclave at 140 °C, 160 °C, 200 °C, and 230 °C for 24 h. The samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and temperature dependence of magnetic susceptibility. It was found that DyF₃ particles possessed an ellipsoidal shape and size varying from 16 to 225 nm. Moroever, the Curie temperature T_C shifts to lower temperatures when the particle size decreases. For the first ime, the critical exponent of the correlation length (ν = 1.51 ± 0.25) and critical size (d₀ = 1.2 ± 0.6 nm) for the dipole ferromagnet DyF₃ has been determined experimentally by the finite-size-scaling theory.

Special Issue: Surface Modification of Engineering and Functional Materials

The ongoing development of both engineering and functional materials is leading to new requirements in terms of their surface properties [...]

Achieving Effective Multimodal Imaging with Rare-Earth Ion-Doped CaF2 Nanoparticles

Nowadays, cancer poses a significant hazard to humans. Limitations in early diagnosis techniques not only result in a waste of healthcare resources but can even lead to delays in diagnosis and treatment, consequently reducing cure rates. Therefore, it is crucial to develop an imaging probe that can provide diagnostic information precisely and rapidly. Here, we used a simple hydrothermal method to design a multimodal imaging probe based on the excellent properties of rare-earth ions. Calcium fluoride co-doped with ytterbium, gadolinium, and neodymium (CaF2:Y,Gd,Nd) nanoparticles (NPs) is highly crystalline, homogeneous in morphology, and displays a high biosafety profile. In addition, in vitro and ex vivo experiments explored the multimodal imaging capability of CaF2:Y,Gd,Nd and demonstrated the efficient performance of CaF2:Y,Gd,Nd during NIR-II fluorescence/photoacoustic/magnetic resonance imaging. Collectively, our novel diagnosis nanoparticle will generate new ideas for the development of multifunctional nanoplatforms for disease diagnosis and treatment.

Near-infrared-emitting upconverting BiVO4 nanoprobes for in vivo fluorescent imaging

Near-infrared (NIR) emitting BiVO₄:Yb³⁺,Tm³⁺ nanoparticles are synthesized by a new solvothermal strategy using solvents of oleic acid and methanol. The obtained BiVO₄:Yb³⁺,Tm³⁺ samples show an average particle size of ≈164 nm and exhibit an asymmetry monoclinic crystal structure of BiVO₄. At NIR excitation of 980 nm, the BiVO₄:Yb³⁺,Tm³⁺ sample exhibits a nearly single NIR emission at ≈796 nm with extremely weak blue emissions from Tm³⁺ ions. These high-energy visible emissions are absorbed by the semiconducting host of BiVO₄ that possesses a bandgap of ≈2.2 eV. Therefore, the NIR excitation to a single intense NIR emission fluorescent BiVO₄ materials could be a potential ideal probe for deep-tissue high-resolution bioimaging. To validate the ability of BiVO₄ materials for bio-applications, we conduct the cytotoxicity experiments. The results show that the cytotoxicity of HeLa cells is negligible at a concentration of 0.2 mg/ml of BiVO₄:Yb³⁺,Tm³⁺ , and the cell viability approaches 90% at a high dosage of 0.5 mg/ml. The Daphnia magna and Zebrafish treated with nanoparticles (0.5 mg/ml) display bright NIR emission without any background, indicating the excellent in vivo fluorescent imaging capacity of BiVO₄:Yb³⁺,Tm³⁺ nanoparticles. Our findings offer an environment-friendly strategy to synthesize BiVO₄ UCL nanophosphors and provide a promising new class of fluorescent probes for biological applications.

Hybrid photoluminescent material from lanthanide fluoride and graphene oxide with strong luminescence intensity as a chemical sensor for mercury ions

In this work, we employed NaxLiyGdF4:Tb3+@PMA@Phen@GO nanocomposite as chemical sensor for selective and sensitive luminescence sensing of toxic Hg2+ metal ion.

Chem-inspired hollow ceria nanozymes with lysosome-targeting for tumor synergistic phototherapy

The precise operation of the hypoxic tumor microenvironment presents a promising way to improve treatment efficacy, in particular in tumor synergistic phototherapy. This work reports an innovative approach to build adenosine triphosphate-modified hollow ceria nanozymes (ATP-HCNPs@Ce6) that manipulate tumor hypoxia to effectively achieve drug delivery. Hollow ceria nanoparticles (HCNPs) exhibit a controllable hollow structure through varying nitric acid concentrations in the nanocomposites. Specifically, ATP modification makes HCNPs exceptionally biocompatible and stable and acts as a regulator of HCNP enzymatic activity. In the stage of drug loading, newly prepared ATP-HCNPs@Ce6 serves as an in situ oxygen-generating agent because of its ability to simulate catalase. Therefore, ATP-HCNPs@Ce6 has adjustable enzymatic properties that act like a "switch" to selectively supply oxygen in response to high levels of hydrogen peroxide expression and the slightly acidic lysosomal environment of the tumor to enhance lysosome-targeted photodynamic therapy. Moreover, the obvious anticancer effects of ATP-HCNPs@Ce6 are demonstrated in vitro and in vivo. Overall, a simple and rapid self-assembly strategy to form and modify multifunctional HCNPs is reported, which may further propel their application in the field of precision tumor treatment.

Unlocking the power of optical imaging in the second biological window: Structuring near-infrared II materials from organic molecules to nanoparticles

Biomedical imaging techniques play a crucial role in clinical diagnosis, surgical intervention, and prognosis. Fluorescence imaging in the second biological window (second near-infrared [NIR-II]; 1000-1700 nm) has attracted attention recently. NIR-II fluorescence imaging offers unique advantages in terms of reduced photon scattering, deep tissue penetration, high sensitivity, and many others. A host of materials, including small organic molecules, single-walled carbon nanotubes, polymeric and rare-earth-doped nanoparticles, have been explored as NIR-II emitting fluorescent probes. Efficient and viable approaches to design and develop fluorescence probes with tunable photophysical properties without compromising other key features are of paramount importance. Various chemical strategies are explored to increase the quantum yield of these imaging agents without compromising their spatiotemporal resolution, specificity, and tissue penetration capabilities. This review summarizes the strategies implemented to design and synthesize NIR-II emitting nanoparticles and small organic molecule-based fluorescent probes for applications in the biomedical field. This article is categorized under: Diagnostic Tools > In Vivo Nanodiagnostics and Imaging Implantable Materials and Surgical Technologies > Nanoscale Tools and Techniques in Surgery.

Fluorine-Induced Surface Metallization for Ammonia Synthesis under Photoexcitation up to 1550 nm

The first observation of surface metallization of TiO_2-x induced by fluoride ions is presented. The emerging metallic states are contributed by the 3d orbital of surface Ti and the 2p orbital of surface bridging F, which are intrinsically originated from the strong electron repulsion between F^- and adjacent Ti³⁺ . The metalized TiO_2-x with reduced work function and downward band bending possesses high electron-donating power to supported Ru species via atomic-scale ohmic contacts, exhibiting unprecedented photocatalytic performances for ammonia synthesis across the entire solar spectrum region (200-1550 nm) at room temperature. Mechanism and kinetic analysis revealed that the loaded Ru could behave as efficient electron sinks to accumulate photogenerated electrons and that the metallic surface markedly enhanced the dissociation of H₂ and N₂ by the hot electrons generated by the visible or even infrared light irradiation.

Upconversion Nanoparticles Encapsulated with Amorphous Silica and Their Emission Quenching by FRET: A Nanosensor Excited by NIR for Mercury Detection

Near-infrared (NIR) region has been considered as a diagnostic window since it avoids sample autofluorescence and light scattering. Upconversion nanoparticles (UCNPs) convert NIR light into high energy excitation light, making them a suitable excitation source for nanoprobes with deep penetration depth and high signal-to-noise ratio. The current work reported a rhodamine-derived probe for the detection of Hg(II). Corresponding absorption and emission responses for Hg(II) and detailed recognizing mechanism were discussed. An absorption titration experiment was performed. It was found that Hg(II) directly bonded with probe with chemical stoichiometry of 1:1, its association constant was calculated as 2.59 × 105 M−1. Such a high value indicated a direct coordination affinity between Hg(II) and this rhodamine-derived probe. Most metal cations exerted no increasing effect on the probe emission or absorption, exhibiting good sensing selectivity of probe towards Hg(II). Upconversion nanoparticles (UCNPs) were firstly encapsulated with silica (SiO2) and then bonded with the probe via a covalent bond. Given a near-infrared (NIR) laser excitation with wavelength of 980 nm, this probe, (E)-2-((3′,6′-bis(diethylamino)-2′,7′-dimethyl-3-oxospiro[isoindoline-1,9′-xanthen]-2-yl)imino)acetaldehyde (denoted as RHO), captured the energy of UCNPs via a FRET (fluorescence resonance energy transfer) path, resulting in the emission quenching of UCNPs. This composite system showed linear sensing behavior towards Hg(II) with high selectivity, which was similar to the case of pure probe. No probe emission, however, was observed from the composite system, which was different from the case of most literature reports. The self-quenching between probe molecules was claimed responsible for the probe emission, which was confirmed by experiment result and analysis. To the best of our knowledge, this is the first demonstration of covalently integrating SiO2-coated UCNPs with a rhodamine-derived probe for Hg(II) sensing.

Rapid aqueous-phase synthesis of highly stable K0.3Bi0.7F2.4 upconversion nanocrystalline particles at low temperature

Lanthanide-doped K_0.3Bi_0.7F_2.4 nanocrystalline particles are synthesized through an ultrafast (only 1 min) and aqueous-phase chemical method at low temperature (room temperature ∼ 90 °C), which can be used as pigments for anti-counterfeiting.

Energy transfer designing in lanthanide-doped upconversion nanoparticles

Lanthanide (Ln3+)-doped upconversion nanoparticles (UCNPs), exhibiting excellent optical properties such as long photoluminescence lifetime, narrow emission bandwidth, and low autofluorescence background, have been applied in many fields, especially in biological analysis and medical diagnostics. Despite the exciting progress, the applications of Ln3+-doped UCNPs are hindered by the small absorption cross-section and low upconversion luminescence efficiency of Ln3+. To this regard, several effective strategies associated with energy transfer designing have been proposed to modulate the upconversion luminescence properties of Ln3+ in the past few decades. In this feature article, we focus on the most recent development of optical property designing in Ln3+-doped UCNPs on the basis of energy transfer between Ln3+-Ln3+, Ln3+-dyes, and Ln3+-quantum dots. Some future efforts towards the energy transfer designing in Ln3+-doped UCNPs are also proposed.

Synthesis, Optical Properties, and Sensing Applications of LaF3:Yb3+/Er3+/Ho3+/Tm3+ Upconversion Nanoparticles

Herein, we successfully synthesized a series of LaF₃:Yb³⁺/Er³⁺/Ho³⁺/Tm³⁺ upconversion nanoparticles (UCNPs) and LaF₃:Yb³⁺_0.20, Er³⁺_0.02@LaF₃:Yb³⁺_0.20 core/shell UCNPs by modifying the amount of NaOH and the reaction time. Hexagonal LaF₃ nanocrystals with uniform particle sizes and bright UC emissions were obtained. The crystal structures of the lanthanide-doped LaF₃ UCNPs were investigated using wide-angle X-ray diffraction. The morphologies and particle sizes of the nanocrystals were determined using transmission electron microscopy. The photoluminescence (PL) spectra of the LaF₃ nanocrystals could be tuned by altering the doping ratio of Er³⁺, Ho³⁺, and Tm³⁺. In addition, the PL intensities increased after coating the UCNP cores with an active shell. The fluorescence intensities of the UCNPs synthesized via a one-hour reaction with the addition of 2.5 or 5 mmol NaOH increased by up to 17 times compared with the sample prepared without the addition of NaOH. By modifying the doping ratio of Yb/Tm, UV-emissive LaF₃ nanocrystals were obtained. After surface modification by ligand exchange, the hydrophobic LaF₃:Yb³⁺_0.20, Er³⁺_0.02@LaF₃:Yb³⁺_0.20 core/shell UCNPs became water-dispersible. These colloid UCNPs could be utilized as a fluorescent probe for the detection of Hg²⁺ ions under 980 nm near-infrared irradiation.

Multifunctional Transferrin Encapsulated GdF3 Nanoparticles for Sentinel Lymph Node and Tumor Imaging

The transferrin encapsulated GdF₃ nanoparticles have been fabricated via biomineralization method. The obtained GdF₃@Tf NPs show an attractive T2MRI and CT enhancement effect. Furthermore, PET and NIR imaging capacity are integrated into nanoparticles through conjugating with radionuclide ⁶⁴Cu and fluorescent dye Cy7. ⁶⁴Cu-GdF₃@Tf-Cy7 NPs are developed and applied in small animal multimodal imaging in vivo. Compared with the previous multimodal imaging agents, ⁶⁴Cu-GdF₃@Tf-Cy7 NPs enable not only precise sentinel lymph node (SLN) identification, but specific imaging for transferrin receptor overexpressed colorectal tumor in vivo. The results reveal that ⁶⁴Cu-GdF₃@Tf-Cy7 NPs are potential and efficient multimodal imaging agents for SLN and tumor preclinical imaging.

Nanomedicine and Early Cancer Diagnosis: Molecular Imaging using Fluorescence Nanoparticles

Incorporating nanotechnology into fluorescent imaging and magnetic resonance imaging (MRI) has shown promising potential for accurate diagnosis of cancer at an earlier stage than the conventional imaging modalities. Molecular imaging (MI) aims to quantitatively characterize, visualize, and measure the biological processes or living cells at molecular and genetic levels. MI modalities have been exploited in different applications including noninvasive determination and visualization of diseased tissues, cell trafficking visualization, early detection, treatment response monitoring, and in vivo visualization of living cells. High-affinity molecular probe and imaging modality to detect the probe are the two main requirements of MI. Recent advances in nanotechnology and allied modalities have facilitated the use of nanoparticles (NPs) as MI probes. Within the extensive group of NPs, fluorescent NPs play a prominent role in optical molecular imaging. The fluorescent NPs used in molecular and cellular imaging can be categorized into three main groups including quantum dots (QDs), upconversion, and dyedoped NPs. Fluorescent NPs have great potential in targeted theranostics including cancer imaging, immunoassay- based cells, proteins and bacteria detections, imaging-guided surgery, and therapy. Fluorescent NPs have shown promising potentials for drug and gene delivery, detection of the chromosomal abnormalities, labeling of DNA, and visualizing DNA replication dynamics. Multifunctional NPs have been successfully used in a single theranostic modality integrating diagnosis and therapy. The unique characteristics of multifunctional NPs make them potential theranostic agents that can be utilized concurrently for diagnosis and therapy. This review provides the state of the art of the applications of nanotechnologies in early cancer diagnosis focusing on fluorescent NPs, their synthesis methods, and perspectives in clinical theranostics.

Binary Nanoparticle Superlattices for Plasmonically Modulating Upconversion Luminescence

Engineering a facile and controllable approach to modulate the spectral properties of lanthanide-doped upconversion nanoparticles (UCNPs) is always an ongoing challenge. Herein, long-range ordered, distinct two-dimensional (2D) binary nanoparticle superlattices (BNSLs) composed of NaREF₄ :Yb/Er (RE = Y and Gd) UCNPs and plasmonic metallic nanoparticles (Au NPs), including AB, AB₃ , and AB₁₃ lattices, are fabricated via a slow evaporation-driven self-assembly to achieve plasmonic modulation of upconversion luminescence (UCL). Optical measurements reveal that typical red-green UCL from UCNPs can be effectively modulated into reddish output in BNSLs, with a drastically shortened lifetime. Notably, for AB₃ - and AB₁₃ -type BNSLs with more proximal Au NPs around each UCNP, modified UCL with fine-structured spectral lineshape is observed. These differences could be interpreted by the interplay of collective plasmon resonance introduced by 2D periodic Au arrays and spectrally selective energy transfer between UCNPs and Au. Thus, fabricating UCNP-Au BNSLs with desired lattice parameters and NP configurations could be a promising way to tailor the UCL through controlled plasmonic modulation.

Up-converting nanoparticles synthesis using hydroxyl-carboxyl chelating agents: Fluoride source effect

The synthesis of lanthanide doped up-converting nanoparticles (UCNPs), whose morphological, structural, and luminescence properties are well suited for applications in optoelectronics, forensics, security, or biomedicine, is of tremendous significance. The most commonly used synthesis method comprises decomposition of organometallic compounds in an oxygen-free environment and subsequent infliction of a biocompatible layer on the particle surface. In this work, hydroxyl-carboxyl (-OH/-COOH) type of chelating agents (citric acid and sodium citrate) are used in situ for the solvothermal synthesis of hydrophilic NaY_0.5Gd_0.3F₄:Yb,Er UCNPs from rare earth nitrate salts and different fluoride sources (NaF, NH₄F, and NH₄HF₂). X-ray powder diffraction showed crystallization of cubic and hexagonal NaY_0.5Gd_0.3F₄:Yb,Er phases in nano- and micro-sized particles, respectively. The content of the hexagonal phase prevails in the samples obtained when Na-citrate is used, while the size and shape of the synthesized mesocrystals are affected by the choice of fluoride source used for precipitation. All particles are functionalized with citrate ligands and emit intense green light at 519 nm and 539 nm (²H_11/2, ⁴S_3/2 → ⁴I_15/2) under near infrared light. The intensity of this emission is distressed by the change in the origin of phonon energy of the host matrix revealed by the change in the number of the excitation photons absorbed per emitted photon.

Recent Advances in Rare-Earth-Doped Nanoparticles for NIR-II Imaging and Cancer Theranostics

Fluorescence imaging in the second near infrared window (NIR-II, 1,000-1,700 nm) has been widely used in cancer diagnosis and treatment due to its high spatial resolution and deep tissue penetration depths. In this work, recent advances in rare-earth-doped nanoparticles (RENPs)-a novel kind of NIR-II nanoprobes-are presented. The main focus of this study is on the modification of RENPs and their applications in NIR-II in vitro and in vivo imaging and cancer theranostics. Finally, the perspectives and challenges of NIR-II RENPs are discussed.

Bismuth(III)-Doped NaYbF4:Tm3+ Fluorides with Highly Efficient Upconversion Emission under Low Irradiance

Concentration quenching of upconversion (UC) luminescence (UCL) is a common phenomenon in rare-earth-doped materials that seriously restricts the concentration of the activator and sensitizer and withholds their UC emissions and quantum yields. In particular, it remains a tremendous challenge to develop one novel strategy based on the introduction of trivalent bismuth (Bi³⁺) ions to exceed the typical thulium (Tm³⁺) ion concentration and reach high-efficiency UC under low illumination. In this work, the Tm³⁺ accommodation capacity can be increased from 2.0 to 8.0 mol % in NaYbF₄:Tm³⁺ materials with the assistance of Bi³⁺ ions, which maintains strong UC emissions with large absolute UC quantum yields under low illumination. Specifically, the total upconversion quantum yield (UCQY) of the as-obtained Na(Tm_0.08Yb_0.60Bi_0.32)F₄ (8Tm60Yb32Bi) sample can reach as high as 1.45% upon continuous-wave (CW) laser excitation at 40 W cm^-2. Strikingly, the total UCQY still remains at a high level (0.41%) even though the CW power density decreases to 1.5 W cm^-2. Moreover, the intrinsic mechanism of the breakthrough in the threshold of concentration quenching of UCL by Bi³⁺ ions was also fully explored. These advances in enhancing UC emissions and UCQYs under a low pump power density offer exciting opportunities for important photonic applications.

A lanthanide ion-doped Ba3Sc2F12 phosphor: hydrothermal synthesis, morphological control, energy transfer, and temperature-sensing performance

Ba₃Sc₂F₁₂ crystals were synthesized by a facile one-step hydrothermal method with Ba/Sc raw material in a ratio of 3 : 2. With the F/Sc ratio increasing from 4 to 8, the obtained crystal's morphology evolved gradually from a strip to a chocolate shape; further, the use of the additives, such as CTAB and EDTA, the obtained crystal's morphology changed from strip to cubic. The energy transfer of Ce³⁺→ Tb³⁺ in the Ba₃Sc₂F₁₂ host was also explored, and it was found to belong to a dipole-dipole interaction mechanism; the color of the light could be adjusted from blue-violet to green due to the different energy transfer efficiencies at different Ce³⁺ and Tb³⁺ ion-doping concentrations. Because of the thermal coupling level of Er³⁺ (²H_11/2→⁴I_15/2 and ⁴S_3/2→⁴I_15/2), Ba₃Sc₂F₁₂:14%Yb³⁺,2%Er³⁺ phosphors showed an excellent temperature-sensing ability with S_A(max) = 0.0043 K^-1 and T_max = 523 K, which are much better than the previously reported values for Yb³⁺/Er³⁺ co-doped systems. The as-prepared lanthanide ion-doped phosphors might have potential to serve as color light/displays and temperature control/sensors.

Uniform Spheres of α-NaYF4:RE3+ (RE=Eu, Tb, Ce, Er, and Tm): Template-Free Synthesis, Multi-Color Photoluminescence, and Their Application in Cellular Imaging

Uniformly dispersed luminescent probes with a high brightness and high resolution are desired in bio imaging fields. Here, ~100 nm sized and well-dispersed spheres of RE3+ doped α-NaYF4 (rare earth (RE) = Eu, Tb, Ce, Er, and Tm) have been facile synthesized through hydrothermal processing in the absence of a template, followed by a proper annealing. The processing window of the cubic structured spheres is wide, because the hydrothermal products are independent of the processing conditions, including reaction time and temperature. The original morphology and crystal structure can be well retained with a calcination temperature up to 600 °C. However, calcination gives rise to a reduction of particle sizes, as a result of the crystallite growth and densification. Under ultraviolet radiation, α-NaYF4:RE3+ spheres show characteristic f-f emissions of RE3+ (RE = Eu, Tb, Ce, Er, and Tm), and exhibit orange red, green, ultraviolet (UV), blue green, and blue emissions, respectively. Mainly because of the near-infrared emission at ~697 nm (5D0→7F4 transitions of Eu3+), the successful imaging of macrophages was achieved by NH2-NaYF4:Eu3+ probes, indicating their excellent imaging capacity for cells in vitro.

Morphology control, spectrum modification and extended optical applications of rare earth ion doped phosphors

This review summarizes the morphology control strategy, phase transfer theory, spectrum modulation, and extended optical applications of RE³⁺-doped phosphors.

Tumor self-responsive upconversion nanomedicines for theranostic applications

To date, malignant tumors continue to be the most lethal disease, causing more than 8.2 million deaths worldwide each year. In recent years, nanostructures based on rare-earth upconversion luminescent nanoparticles have shown significant advantages in the integration of multimodal imaging and therapy. Compared with normal tissues, the tumor microenvironment (TME) exhibits unique characteristics including high interstitial fluid pressure, abnormal blood vessels, a hypoxic and slightly acidic environment, and high levels of glutathione (GSH) and hydrogen peroxide (H2O2). According to these characteristics, increasing attention in the antitumor field has been given to designing nanomedicines with specific responses to the TME based on rare-earth upconversion nanoparticles (UCNPs) and to achieving efficient tumor diagnosis and treatment under the premise of reducing side effects. Nevertheless, a review that systematically summarizes TME-responsive upconversion nanomedicines (UCNMs) for realizing tumor self-enhanced theranostics has not been published to date. In this review, we summarize the recent progress made in UCNP-based nanotherapeutics by highlighting the increasingly developing trend of TME-responsive UCNMs. The general characteristics of the TME are introduced in detail and their utilization in designing TME-responsive UCNMs is systematically discussed. Based on NIR light-excited optical imaging, we discuss the superiority of UCNMs when applied in tumor theranostics with an emphasis on how to use them to realize TME-mediated multimodal imaging-guided therapy.

Novel nanotechnology and near-infrared photodynamic therapy to kill periodontitis-related biofilm pathogens and protect the periodontium

OBJECTIVE

Periodontal tissue destruction and tooth loss are increasingly a worldwide problem as the population ages. Periodontitis is caused by bacterial infection and biofilm plaque buildup. Therefore, the objectives of this study were to: (1) develop a near-infrared light (NIR)-triggered core-shell nanostructure of upconversion nanoparticles and TiO₂ (UCNPs@TiO₂), and (2) investigate its inhibitory effects via antibacterial photodynamic therapy (aPDT) against periodontitis-related pathogens.

METHODS

The core β-NaYF₄:Yb³⁺,Tm³⁺ were synthesized via thermal decomposition and further modified with the TiO₂ shell via a hydrothermal method. The core-shell structure and the upconversion fluorescence-induced aPDT treatment via 980nm laser were studied. Three periodontitis-related pathogens Streptococcus sanguinis (S. sanguinis), Porphyromonas gingivalis (P. gingivalis) and Fusobacterium nucleatum (F. nucleatum) were investigated. The killing activity against planktonic bacteria was detected by a time-kill assay. Single species 4-day biofilms on dentin were tested by live/dead staining, colony-forming units (CFU), and metabolic activity.

RESULTS

The hexagonal shaped UCNPs@TiO₂ had an average diameter of 39.7nm. UCNPs@TiO₂ nanoparticles had positively charged (+12.4mV) surface and were biocompatible and non-cytotoxic. Under the excitation of NIR light (980nm), the core NaYF₄:Yb³⁺,Tm³⁺ UCNPs could emit intense ultraviolet (UV) light, which further triggered the aPDT function of the shell TiO₂ via energy transfer, thereby realizing the remarkable antibacterial effects against planktons and biofilms of periodontitis-associated pathogens. NIR-triggered UCNPs@TiO₂ achieved much greater reduction in biofilms than control (p<0.05). Biofilm CFU was reduced by 3-4 orders of magnitude via NIR-triggered aPDT, which is significantly greater than that of negative control and commercial aPDT control groups. The killing efficacy of UCNPs@TiO₂-based aPDT against the three species was ranked to be: S. sanguinis<F. nucleatum=P. gingivalis. Metabolic activities of biofilms were also greatly reduced via NIR-triggered aPDT (p<0.05).

SIGNIFICANCE

Upconversion fluorescence-based aPDT achieved strong inhibiting effects against all three species of periodontitis-related pathogens. This novel nanotechnology demonstrated a high promise to inhibit periodontitis, with exciting potential to combat other oral infectious diseases such as deep endodontic infections.

Improved Red Emission and Short-Wavelength Infrared Luminescence under 808 nm Laser for Tumor Theranostics

In this research, a multimodal imaging platform guided photodynamic theranostics under 808 nm was designed using a NaErF₄:Tm@NaYF₄:Yb@NaLuF₄:Nd,Yb-ZnPc structure. Unlike conventional codoped Yb³⁺/Er³⁺ system, Er³⁺ ions as activator and sensitizer were used to improve the up-conversion energy transfer processes. Furthermore, higher energy transfer processes between Er³⁺ ions could be obtained through doped 1% Tm³⁺ ions as an energy trapping center in the NaErF₄. This platform could emit much brighter upconversion luminescence (UCL) (124-fold enhancement for red emission) and short wavelength infrared (SWIR) emission under single 808 nm laser excitation. Importantly, the SWIR imaging with higher resolution and better signal-to-noise ratio can pass the blood-brain barrier to see the brain vessels. Because of the enhanced red emission, the UCL nanoparticles were combined with ZnPc agent to exhibit photodynamic therapy (PDT) effect, and its distribution and excretion could be detected by the photoacoustic (PA) imaging under single near-infrared (NIR) laser. Thus, this platform could be used as multimodal imaging (SWIR, PA, CT, and UCL) guided PDT agent under single 808 nm laser.

Rare earth nanofluorides: synthesis using ionic liquids

This review presents a comprehensive summary of the research progress on the synthesis of rare earth fluoride nanomaterials using the most common methods of synthesis. Special focus is on syntheses utilising ionic liquids, which is a new and promising way of preparing nanomaterials without the use of dangerous organic solvents (toxic, flammable, or combustive). Rare earth fluoride nanoparticles can be obtained with a high yield, purity, and crystallinity, and with different morphologies and luminescent properties depending on the selected method of synthesis.

Comparative investigation of the optical spectroscopic and thermal effect in Nd3+-doped nanoparticles

Nd3+-doped nanoparticles involving 808 nm excitation hold great promise in various biomedical applications, such as bioimaging, biodetection, theranostics and optogenetics. Here we present the synthesis and characterization of core-multishell Nd3+-doped nanoparticles displaying excellent optical properties. We systematically studied the influence of doping concentration, nanostructure design, excitation wavelength and size effect on the upconversion luminescence of Nd3+-doped nanoparticles. Remarkably, the emission intensity of optimized nanoparticles with 808 nm excitation is three times higher than the emission intensity of those with 980 nm excitation. Surprisingly, the optical profiles of Nd3+-doped nanoparticles strongly depend on the excitation wavelengths. The dominant effect responsible for the emission intensity difference and the energy transfer mechanism upon different excitation wavelengths are investigated. Interestingly, the heavily Nd3+-doped nanoparticles not only display efficient upconversion luminescence, but also are able to convert the excitation source to heat under a single 808 nm excitation source. Importantly, these efforts will lead to Nd3+-doped nanoparticles with unprecedented optical and thermal properties that will have broad utility in fundamental research and technological applications.

In situ reversible color variation of a ready-made upconversion material using the designed component of a three-state fluorescence switching system

In recent years, upconversion materials have attracted considerable attention because of their unique physicochemical features. Numerous studies have focused on the synthesis of upconversion materials with different colors. However, an easier way to vary the upconversion colors without changing the materials' components has not been extensively studied. In this study, we realized the in situ color variation of the designed upconversion material with the help of a three-state fluorescence switching hybrid device. The device was composed of Prussian blue and upconversion materials; the former element functioned as a fluorescence resonance energy transfer acceptor and the latter acted as a donor. Smartly applying the RGB color model guaranteed multicolor of the device. Moreover, the highest fluorescence contrast of the three-state fluorescence switching system was 86% (larger than the result of a previous study), and the three-state reversibility was remarkable; this was probably owing to the unique layer-by-layer dripping/electrodepositing assembly method. To the best of our knowledge, the in situ reversible color variation of the ready-made upconversion material has been demonstrated for the first time.

Dye-Assembled Upconversion Nanocomposite for Luminescence Ratiometric in Vivo Bioimaging of Copper Ions

Overdose of Cu²⁺ is associated with multiple diseases, such as Wilson disease, Parkinson disease, and Alzheimer disease. Therefore, detections of Cu²⁺ in vivo and in vitro are meaningful. Near-infrared fluorescent probes are commonly applied for the detection of Cu²⁺ in real time. With mono detection signal provided, these probes are not persuasive when applied to complicated biological environments, such as cells and animals. In this report, we conjugated the organic fluorescent probe CYDAC₁₆ with the UCNPs (lanthanide-doped upconversion nanoparticles) to develop a ratiometric luminescent probe for Cu²⁺. The composite material UCNPs-CYDAC₁₆ provides a ratiometric signal based on an upconversion luminescence 660 and 800 nm. With good sensitivity and selectivity for Cu²⁺, it works well in vivo and in vitro for the detection of Cu²⁺. We believe it is promising in further biological applications.

A facile aqueous synthesis strategy for hexagonal phase NaGdF4 nanorods

A facile aqueous synthesis method is explored to synthesize hydrophilic β-NaGdF₄ nanorods at 60 °C.

Fluorolytic Sol–Gel Synthesis of Nanometal Fluorides: Accessing New Materials for Optical Applications

The potential of fluorolytic sol–gel synthesis for a wide variety of applications in the field of optical materials is reviewed. Based on the fluorolytic sol–gel synthesis of nanometal fluorides, sols of complex fluorometalates have become available that exhibit superior optical properties over known classical binary metal fluorides as, for instance, magnesium fluoride, calcium fluoride, or strontium fluoride, respectively. The synthesis of transparent sols of magnesium fluoroaluminates of the general composition MgxAlFy, and fluoroperovskites, [K1−xNax]MgF3, is reported. Antireflective coatings fabricated from MgF2, CaF2, MgxAlFy, and [K1−xNax]MgF3 sols and their relevant properties are comprehensively described. Especially the heavier alkaline earth metal fluorides and the fluorperovskites crystallizing in a cubic crystal structure are excellent hosts for rare earth (RE) metals. Thus, the second chapter reflects the synthesis approach and the properties of luminescent systems based on RE-doped alkaline earth metal fluorides and [K1−xNax]MgF3 phases.