Graphene Oxide Surface Modification of Reverse Osmosis (RO) Membrane via Langmuir-Blodgett Technique: Balancing Performance and Antifouling Properties

The reverse osmosis water treatment process is prone to fouling issues, prompting the exploration of various membrane modification techniques to address this challenge. The primary objective of this study was to develop a precise method for modifying the surface of reverse osmosis membranes to enhance their antifouling properties. The Langmuir-Blodgett technique was employed to transfer aminated graphene oxide films assembled at the air-liquid interface, under specific surface pressure conditions, to the polyamide surface with pre-activated carboxylic groups. The microstructure and distribution of graphene oxide along the modified membrane were characterized using SEM, AFM, and Raman mapping techniques. Modification carried out at the optimal surface pressure value improved the membrane hydrophilicity and reduced the surface roughness, thereby enhancing the antifouling properties against colloidal fouling. The flux recovery ratio after modification increased from 65% to 87%, maintaining high permeability. The modified membranes exhibited superior performance compared to the unmodified membranes during long-term fouling tests. This membrane modification technique can be easily scaled using the roll-to-roll approach and requires minimal consumption of the modifier used.

Layer-by-layer Assembly of Nanosheets with Matching Size and Shape for More Stable Membrane Structure than Nanosheet-Polymer Assembly

Layer-by-layer (LbL) assembly of oppositely charged materials has been widely used as an approach to make two-dimensional (2D) nanosheet-based membranes, which often involves 2D nanosheets being alternately deposited with polymer-based polyelectrolytes to obtain an electrostabilized nanosheet-polymer structure. In this study, we hypothesized that using 2D nanosheets with matching physical properties as both polyanions and polycations may result in a more ordered nanostructure with better stability than a nanosheet-polymer structure. To compare the differences between nanosheet-nanosheet vs nanosheet-polymer structures, we assembled negatively charged molybdenum disulfide nanosheets (MoS2) with either positively charged graphene oxide (PrGO) nanosheets or positively charged polymer (PDDA). Using combined measurements by ellipsometer and quartz crystal microbalance with dissipation, we discovered that the swelling of MoS2-PrGO in ionic solutions was 60% lower than that of MoS2-PDDA membranes. Meanwhile, the MoS2-PrGO membrane retained its permeability upon drying, whereas the permeability of MoS2-PDDA decreased by 40% due to the restacking of MoS2. Overall, the MoS2-PrGO membrane demonstrated a better filtration performance. Additionally, our X-ray photoelectron spectroscopy results and analysis on layer density revealed a clearer transition in material composition during the LbL synthesis of MoS2-PrGO membranes, and the X-ray diffraction pattern suggested its resemblance to an ordered, layer-stacked structure. In conclusion, the MoS2-PrGO membrane made with nanosheets with matching size, shape, and charge density exhibited a much more aligned stacking structure, resulting in reduced membrane swelling under high salinity solutions, controlled restacking, and improved separation performance.

Antimicrobial coatings based on amine-terminated graphene oxide and Nafion with remarkable thermal resistance

We present a novel type of layer-by-layer (LbL) waterborne coating based on Nafion and amine-terminated graphene oxide (GO-NH2) that inhibits the growth of Escherichia coli and Staphylococcus aureus by more than 99% and this performance is not compromised upon extensive thermal annealing at 200 °C. Quartz crystal microbalance (QCM) sensorgrams allow the real time monitoring of the build-up of the LbL assemblies, a process that relies on the strong electrostatic interactions between Nafion (pH = 2.7, ζ = -54.8 mV) and GO-NH2 (pH = 2, ζ = 26.7 mV). Atomic force microscopy (AFM), contact angle and zeta potential measurements were used to characterise the multilayer assemblies. We demonstrate here that Nafion/GO-NH2 advanced coatings can offer drug-free and long-lasting solutions to microbial colonization and can withstand dry heat sterilization, without any decline in their performance.

Conductive Nanofilms with Oppositely Charged Reduced Graphene Oxides as a Base for Electroactive Coatings and Sensors

We demonstrate a method for the formation of multilayers composed of reduced graphene oxide (rGO), which can be used for transparent, conducting thin films. Using the layer-by-layer (LbL) assembly of positively and negatively charged GO sheets, we could obtain thin films with highly controllable sheet resistance. The natural negative charge of graphene oxide was turned to positive by the amidation reaction. After forming the multilayer films, the graphene oxide underwent thermal reduction at temperatures above 150 °C. The (rGO+/rGO−) films were characterized by UV-Vis and scanning electron microscopy (SEM), and their conductivity was measured by the four-point method. We found that after deposition of five (rGO+/rGO−), the coating structure reached the percolation limit, and the film resistance decreased more gradually to around 20 kΩ/sq for the films obtained by eleven deposition cycles with graphene oxide reduced at 250 °C. The formation of thin films on polyimide allows the forming of new flexible conductive materials, which can find applications, e.g., in biomedicine as new electroactive, low-cost, disposable sensors.

Wafer-Scale Lateral Self-Assembly of Mosaic Ti3C2Tx MXene Monolayer Films

Bottom-up assembly of two-dimensional (2D) materials into macroscale morphologies with emergent properties requires control of the material surroundings, so that energetically favorable conditions direct the assembly process. MXenes, a class of recently developed 2D materials, have found new applications in areas such as electrochemical energy storage, nanoscale electronics, sensors, and biosensors. In this paper, we present a lateral self-assembly method for wafer-scale deposition of a mosaic-type 2D MXene flake monolayer that spontaneously orders at the interface between two immiscible solvents. ReaxFF molecular dynamics simulations elucidate the interactions of a MXene flake with the solvents and its stability at the liquid/liquid interface, the prerequisite for MXene flakes self-assembly at the interface. Moreover, facile transfer of this monolayer onto a flat substrate (Si, glass) results in high-coverage monolayer films with uniform thickness and homogeneous optical properties. Multiscale characterization of the resulting films reveals the mosaic structure and sheds light on the electronic properties of the films, which exhibit good electrical conductivity over cm-scale areas.

Interfacial control and design of conductive nanomaterials for transparent nanocomposite electrodes

A few critical issues in preparing transparent conductive electrodes (TCEs) based on solution-processable conductive nanomaterials are their low electrical conductivity and the unfavorable trade-off between electrical conductivity and optical transparency, which are closely related to the organic ligands bound to the nanomaterial surface. In particular, bulky/insulating organic ligands bound to the surface of conductive nanomaterials unavoidably act as high contact resistance sites at the interfaces between neighboring nanomaterials, which adversely affects the charge transfer kinetics of the resultant TCEs. This article reviews the latest research status of various interfacial control approaches for solution-processable TCEs. We describe how these approaches can be effectively applied to conductive nanomaterials and how interface-controlled conductive nanomaterials can be employed to improve the electrical and/or electrochemical performance of various transparent nanocomposite electrodes, including TCEs, energy storage electrodes, and electrochromic electrodes. Last, we provide perspectives on the development direction for next-generation transparent nanocomposite electrodes and breakthroughs for significantly mitigating the complex trade-off between their electrical/electrochemical performance and optical transparency.

Nanoscale Assembly of 2D Materials for Energy and Environmental Applications

Rational design of 2D materials is crucial for the realization of their profound implications in energy and environmental fields. The past decade has witnessed significant developments in 2D material research, yet a number of critical challenges remain for real-world applications. Nanoscale assembly, precise control over the orientational and positional ordering, and complex interfaces among 2D layers are essential for the continued progress of 2D materials, especially for energy storage and conversion and environmental remediation. Herein, recent progress, the status, future prospects, and challenges associated with nanoscopic assembly of 2D materials are highlighted, specifically targeting energy and environmental applications. Geometric dimensional diversity of 2D material assembly is focused on, based on novel assembly mechanisms, including 1D fibers from the colloidal liquid crystalline phase, 2D films by interfacial tension (Marangoni effect), and 3D nanoarchitecture assembly by electrochemical processes. Relevant critical advantages of 2D material assembly are highlighted for application fields, including secondary batteries, supercapacitors, catalysts, gas sensors, desalination, and water decontamination.

Starch-Mediated Immobilization, Photochemical Reduction, and Gas Sensitivity of Graphene Oxide Films

This work unveils the roles played by potato starch (ST) in the immobilization, photochemical reduction, and gas sensitivity of graphene oxide (GO) films. The ST/GO films are assembled layer by layer (LbL) onto quartz substrates by establishing mutual hydrogen bonds that drive a stepwise film growth, with equal amounts of materials being adsorbed in each deposition cycle. Afterward, the films are photochemically reduced with UV irradiation (254 nm), following a first-order kinetics that proceeds much faster when GO is assembled along with ST instead of a nonoxygenated polyelectrolyte, namely, poly(diallyl dimethylammonium) hydrochloride (PDAC). Finally, the gas-sensing performance of ST/reduced graphene oxide (RGO) and PDAC/RGO sensors fabricated via LbL atop of gold interdigitated microelectrodes is evaluated at different relative humidity levels and in different concentrations of ammonia, ethanol, and acetone. In comparison to the PDAC/RGO sensor, the ones containing ST are much more sensitive, especially when operating in a high-relative-humidity environment. An array comprising these chemical sensors provides unique electrical fingerprints for each of the investigated analytes and is capable of discriminating and quantifying them in a wide range of concentrations, from 10 to 1000 ppm.

Influence of Host-Guest Interaction between Chiral Selectors and Probes on the Enantioseparation Properties of Graphene Oxide Membranes

Graphene oxide (GO)-based membranes have displayed superior performances in the chiral resolution compared with conventional polymer-based and inorganic membranes. However, the effect of the host-guest interaction between chiral selectors and probes on the enantioseparation properties of GO-based membranes remains to be established. In this work, l-phenylalanine (l-Phe, as the chiral selector)-modified GO-based (l-Phe-GO) membranes were fabricated, and their enantioseparation performances toward various enantiomers, that is, d- and l-phenylalanine (d- and l-Phe), d- and l-methionine (d- and l-Met), N-acyl-d-phenylalanine (N-acyl-d-Phe) and N-acyl-l-phenylalanine (N-acyl-l-Phe), and N-acyl-d-methionine (N-acyl-d-Met) and N-acyl-l-methionine (N-acyl-l-Met), were detected. Results show that (i) l-Phe is preferential to transport d-enantiomers relative to l-enantiomers; (ii) as far as d-enantiomers are concerned, the d-Phe-like enantiomers move faster than d-Met-like ones through the l-Phe-GO membrane owing to their different host-guest interactions. The strength of interactions between chiral selectors and probes was further confirmed from both experimental and theoretical standpoints. In the former case, the enantioselective adsorption of l-Phe-GO nanosheets toward the aforementioned enantiomers demonstrates that l-Phe delivers a higher adsorption capacity to d-enantiomers relative to l-enantiomers, and meanwhile, d-Phe-like enantiomers are better than d-Met-like enantiomers in the adsorption capacity. In the latter case, the chiral separation mechanism is clarified using the periodical density functional theory (DFT) calculation, indicating that l-Phe interacts with d-enantiomers more strongly than l-enantiomers. Especially, our calculations unveil that the difference in the interaction strength is principally dominated by the nonstereoselective interactions between chiral probes and the GO surface. Therefore, our findings suggest that the nonstereoselective weak interaction can be employed to improve the enantioselectivity of GO-based membranes.

Mechanically strong and electrically conductive multilayer MXene nanocomposites

Polymer nanocomposites offer the opportunity to bridge properties of nanomaterials to the macroscale. In this work, layer-by-layer (LbL) assembly is used to demonstrate nanocomposites of 2D titanium carbide nanosheets (MXene) and clay nanoplatelets (montmorillonite) to fabricate freestanding thin films with unique multifunctional properties. These thin films can be tuned by adjusting the thickness to exhibit a tensile strength of 138 MPa-225 MPa, EMI specific shielding effectiveness normalized to thickness and density up to 24 550 dB cm² g^-1, and sheet resistance from 855 Ω sq^-1-3.27 kΩ sq^-1 (corresponding to a range of conductivity from 53 S m^-1 to 125 S m^-1). This composite is the strongest MXene-based LbL film prepared to date, in part due to the nacre-like brick-and-mortar structure. Ultra-strong, multifunctional films of this nature are desirable for many applications ranging from membranes, to structural and multifunctional composites, energy harvesting and storage, and materials for aerospace.

Layer-by-Layer Assembly: Recent Progress from Layered Assemblies to Layered Nanoarchitectonics

As an emerging concept for the development of new materials with nanoscale features, nanoarchitectonics has received significant recent attention. Among the various approaches that have been developed in this area, the fixed-direction construction of functional materials, such as layered fabrication, offers a helpful starting point to demonstrate the huge potential of nanoarchitectonics. In particular, the combination of nanoarchitectonics with layer-by-layer (LbL) assembly and a large degree of freedom in component availability and technical applicability would offer significant benefits to the fabrication of functional materials. In this Minireview, recent progress in LbL assembly is briefly summarized. After introducing the basics of LbL assembly, recent advances in LbL research are discussed, categorized according to physical, chemical, and biological innovations, along with the fabrication of hierarchical structures. Examples of LbL assemblies with graphene oxide are also described to demonstrate the broad applicability of LbL assembly, even with a fixed material.

Bio-interfactants as double-sided tapes for graphene oxide

We present a versatile and highly substrate-independent approach for preparing multisandwich layers based on thermally reduced Graphene Oxide (rGO) which gets strongly attached by bio-interfactants using a layer-by-layer (LBL) aqueous dipping and rinsing process. The process allows for the deposition of homogeneous ultra-thin films (∼5.5 nm) in distinct surface topographies, thicknesses and compositions by varying the bio-interfactant layer(s). The layers formed on quartz or other semi conductive material are electrically conductive, flexible, and transparent. The here-developed approach could be applied for the fabrication of wearables, sensors, and antistatic transparent films.

Interface Engineering of Hematite with Nacre-like Catalytic Multilayers for Solar Water Oxidation

An efficient water oxidation photoanode based on hematite has been designed and fabricated by tailored assembly of graphene oxide (GO) nanosheets and cobalt polyoxometalate (Co-POM) water oxidation catalysts into a nacre-like multilayer architecture on a hematite photoanode. The deposition of catalytic multilayers provides a high photocatalytic efficiency and photoelectrochemical stability to underlying hematite photoanodes. Compared to the bare counterpart, the catalytic multilayer electrode exhibits a significantly higher photocurrent density and large cathodic shift in onset potential (∼369 mV) even at neutral pH conditions due to the improved charge transport and catalytic efficiency from the rational and precise assembly of GO and Co-POM. Unexpectedly, the polymeric base layer deposited prior to the catalytic multilayers improves the performance even more by facilitating the transfer of photogenerated holes for water oxidation through modification of the flat band potential of the underlying photoelectrode. This approach utilizing polymeric base and catalytic multilayers provides an insight into the design of highly efficient photoelectrodes and devices for artificial photosynthesis.

Continuous Langmuir-Blodgett Deposition and Transfer by Controlled Edge-to-Edge Assembly of Floating 2D Materials

The Langmuir-Blodgett technique is one of the most controlled methods to deposit monomolecular layers of floating or surface active materials but has lacked the ability to coat truly large-area substrates. In this work, by manipulating single-layer dispersions of graphene oxide (GO) and thermally exfoliated GO into water-immiscible spreading solvents, unlike traditional Langmuir-Blodgett deposition which requires densification achieved by compressing barriers, we demonstrate the ability to control the 2D aggregation and densification behavior of these floating materials using a barrier-free method. This is done by controlling the edge-to-edge interactions through modified subphase conditions and by utilizing the distance-dependent spreading pressure of the deposition solvent. These phenomena allow substrates to be coated by continuous deposition and substrate withdrawal-enabling roll-to-roll deposition and patterning of large-area substrates such as flexible polyethylene terephthalate. The aggregation and solvent-driven densification phenomena are examined by in situ Brewster angle video microscopy and by measuring the local spreading pressure induced by the spreading solvent acting on the floating materials using a Langmuir-Adam balance. As an example, the performance of films deposited in this way is assessed as passivation layers for Ag nanowire-based transparent conductors.

Controllable Bipolar Doping of Graphene with 2D Molecular Dopants

The fine control of graphene doping levels over a wide energy range remains a challenging issue for the electronic applications of graphene. Here, the controllable doping of chemical vapor deposited graphene, which provides a wide range of energy levels (shifts up to ± 0.5 eV), is demonstrated through physical contact with chemically versatile graphene oxide (GO) sheets, a 2D dopant that can be solution-processed. GO sheets are a p-type dopant due to their abundance of electron-withdrawing functional groups. To expand the energy window of GO-doped graphene, the GO surface is chemically modified with electron-donating ethylene diamine molecules. The amine-functionalized GO sheets exhibit strong n-type doping behaviors. In addition, the particular physicochemical characteristics of the GO sheets, namely their sheet sizes, number of layers, and degree of oxidation and amine functionality, are systematically varied to finely tune their energy levels. Finally, the tailor-made GO sheet dopants are applied into graphene-based electronic devices, which are found to exhibit improved device performances. These results demonstrate the potential of GO sheet dopants in many graphene-based electronics applications.

Fabrication of high-performance graphene nanoplatelet-based transparent electrodes via self-interlayer-exfoliation control

Graphene nanoplatelets (GNP) have attracted considerable attention due to their high yield and fabrication route that is scalable to enable graphene production. However, the absence of a means of fabricating a transparent and conductive GNP film has been the biggest obstacle to the replacement of pristine graphene. Here, we report on a novel means of fabricating uniform and thin GNP-based high-performance transparent electrodes for flexible and stretchable optoelectronic devices involving the use of an adhesive polymer layer (PMMA) as a GNP layer controller and by forming a hybrid GNP/AgNW electrode embedded on PET or PDMS. Relative to the commercially available indium tin oxide (ITO) film on a PET substrate, a GNP-based electrode composed of hybrid GNP/AgNW on PET exhibits superb optical, physical, and electrical properties: a sheet resistance of 12 Ω sq^-1 with 87.4% transmittance, a variable work function from 4.16 to 5.26 eV, an ultra-smooth surface, a rate of resistance increase of only 4.0% after 100 000 bending cycles, stretchability to 50% of tensile strain, and robust stability against oxidation. Moreover, the GNP-based electrode composed of hybrid Cl-doped GNP/AgNW shows outstanding performance in actual organic light-emitting diodes (OLEDs) by exhibiting an increased current efficiency of 29.5% and an increased luminous efficiency of 36.2%, relative to the commercial ITO electrode on PET.

Self-Assembled Graphene-Based Architectures and Their Applications

Due to unique planar structures and remarkable thermal, electronic, and mechanical properties, chemically modified graphenes (CMGs) such as graphene oxides, reduced graphene oxides, and the related derivatives are recognized as the attractive building blocks for "bottom-up" nanotechnology, while self-assembly of CMGs has emerged as one of the most promising approaches to construct advanced functional materials/systems based on graphene. By virtue of a variety of noncovalent forces like hydrogen bonding, van der Waals interaction, metal-to-ligand bonds, electrostatic attraction, hydrophobic-hydrophilic interactions, and π-π interactions, the CMGs bearing various functional groups are highly desirable for the assemblies with themselves and a variety of organic and/or inorganic species which can yield various hierarchical nanostructures and macroscopic composites endowed with unique structures, properties, and functions for widespread technological applications such as electronics, optoelectronics, electrocatalysis/photocatalysis, environment, and energy storage and conversion. In this review, significant recent advances concerning the self-assembly of CMGs are summarized, and the broad applications of self-assembled graphene-based materials as well as some future opportunities and challenges in this vibrant area are elucidated.

Separation and purification using GO and r-GO membranes

Many materials with varied characteristics have been used for water purification and separation applications. Recently discovered graphene oxide (GO), a two-dimensional derivative of graphene has been considered as a promising membrane material for water purification due to its excellent hydrophilicity, high water permeability, and excellent ionic/molecular separation properties. This review is focussed on the possible versatile applicability of GO membranes. It is also known that selective reduction of GO results in membranes with a pore size of ∼0.35 nm, ideally suited for desalination applications. This article presents the applicability of graphene-based membranes for multiple separation applications. This is indeed the first review article outlining a comparison of GO and r-GO membranes and discussing the suitability for applications based on the porosity of the membranes.

This review article outlines a comparison of GO and r-GO membranes for separation and purification applications.

Bio-inspired layered chitosan/graphene oxide nanocomposite hydrogels with high strength and pH-driven shape memory effect

The layered nanocomposite hydrogel films containing chitosan (CS) and graphene oxide (GO) have been prepared by water evaporation induced self-assembly and subsequent physical cross-linking in alkaline solution. The layered CS/GO hydrogel films obtained have a nacre-like brick-and-mortar microstructure, which contributes to their excellent mechanical properties. The tensile strength and elongation at break of the hydrogel films with 5wt% GO are 5.35MPa and 193.5%, respectively, which are comparable to natural costal cartilage. Furthermore, the CS/GO hydrogel films exhibited pH-driven shape memory effect, and this unique phenomenon is mainly attributed to the reversible transition of partial physically cross-linking corresponding to hydrogen bondings and hydrophobic interactions between CS polymer chains due to pH changing.

Three-Dimensional Printed Graphene Foams

An automated metal powder three-dimensional (3D) printing method for in situ synthesis of free-standing 3D graphene foams (GFs) was successfully modeled by manually placing a mixture of Ni and sucrose onto a platform and then using a commercial CO₂ laser to convert the Ni/sucrose mixture into 3D GFs. The sucrose acted as the solid carbon source for graphene, and the sintered Ni metal acted as the catalyst and template for graphene growth. This simple and efficient method combines powder metallurgy templating with 3D printing techniques and enables direct in situ 3D printing of GFs with no high-temperature furnace or lengthy growth process required. The 3D printed GFs show high-porosity (∼99.3%), low-density (∼0.015g cm^-3), high-quality, and multilayered graphene features. The GFs have an electrical conductivity of ∼8.7 S cm^-1, a remarkable storage modulus of ∼11 kPa, and a high damping capacity of ∼0.06. These excellent physical properties of 3D printed GFs indicate potential applications in fields requiring rapid design and manufacturing of 3D carbon materials, for example, energy storage devices, damping materials, and sound absorption.

Layer-by-layer assembly of versatile nanoarchitectures with diverse dimensionality: a new perspective for rational construction of multilayer assemblies

Over the past few decades, layer-by-layer (LbL) assembly of multilayer thin films has garnered considerable interest on account of its ability to modulate nanometer control over film thickness and its extensive choice of usable materials for coating planar and particulate substrates, thus allowing for the fabrication of responsive and functional thin films for their potential applications in a myriad of fields. Herein, we provide elaborate information on the current developments of LbL assembly techniques including different properties, molecular interactions, and assembly methods associated with this promising bottom-up strategy. In particular, we highlight the principle for rational design and fabrication of a large variety of multilayer thin film systems including multi-dimensional capsules or spatially hierarchical nanostructures based on the LbL assembly technique. Moreover, we discuss how to judiciously choose the building block pairs when exerting the LbL assembly buildup which enables the engineering of multilayer thin films with tailor-made physicochemical properties. Furthermore, versatile applications of the diverse LbL-assembled nanomaterials are itemized and elucidated in light of specific technological fields. Finally, we provide a brief perspective and potential future challenges of the LbL assembly technology. It is anticipated that our current review could provide a wealth of guided information on the LbL assembly technique and furnish firm grounds for rational design of LbL assembled multilayer assemblies toward tangible applications.

Multidimensional Thin Film Hybrid Electrodes with MoS2 Multilayer for Electrocatalytic Hydrogen Evolution Reaction

Hybrid electrodes are widely used in various energy storage and conversion devices. However, conventional fabrication methods like simple mixing allow only limited control over the internal electrode structure, and it is often difficult to elucidate the structure-property relationship among the electrode components. Taking advantage of the versatile layer-by-layer (LbL) assembly method, herein we report the preparation of electrocatalytic thin film electrodes for hydrogen evolution reaction (HER), highlighting the importance of nanoscale composition in multidimensional hybrid electrodes. The fabrication utilized the electrostatic interaction between the two components: catalytically active two-dimensional MoS₂ nanosheets and conductive, one-dimensional multiwalled carbon nanotube (MWNT) support. The electrocatalytic activity was found to be highly tunable by adjusting the thickness of the electrode, suggesting structural dependence of electron transfer and mass transport between the electrolyte and electrode, which is otherwise difficult to investigate in electrodes fabricated by simple conventional methods. Furthermore, the detailed mechanism of HER on the hybrid electrode was also investigated, revealing the fine balance between the catalytic activity of MoS₂ and conductivity of MWNT. We anticipate that this unique approach will offer new insights into the nanoscale control of electrode architecture and the development of novel electroactive catalysts.

Three-Dimensional Rebar Graphene

Free-standing robust three-dimensional (3D) rebar graphene foams (GFs) were developed by a powder metallurgy template method with multiwalled carbon nanotubes (MWCNTs) as a reinforcing bar, sintered Ni skeletons as a template and catalyst, and sucrose as a solid carbon source. As a reinforcement and bridge between different graphene sheets and carbon shells, MWCNTs improved the thermostability, storage modulus (290.1 kPa) and conductivity (21.82 S cm^-1) of 3D GF resulting in a high porosity and structurally stable 3D rebar GF. The 3D rebar GF can support >3150× the foam's weight with no irreversible height change, and shows only a ∼25% irreversible height change after loading >8500× the foam's weight. The 3D rebar GF also shows stable performance as a highly porous electrode in lithium ion capacitors (LICs) with an energy density of 32 Wh kg^-1. After 500 cycles of testing at a high current density of 6.50 mA cm^-2, the LIC shows 78% energy density retention. These properties indicate promising applications with 3D rebar GFs in devices requiring stable mechanical and electrochemical properties.

Functional Graphene Nanomaterials Based Architectures: Biointeractions, Fabrications, and Emerging Biological Applications

Functional graphene nanomaterials (FGNs) are fast emerging materials with extremely unique physical and chemical properties and physiological ability to interfere and/or interact with bioorganisms; as a result, FGNs present manifold possibilities for diverse biological applications. Beyond their use in drug/gene delivery, phototherapy, and bioimaging, recent studies have revealed that FGNs can significantly promote interfacial biointeractions, in particular, with proteins, mammalian cells/stem cells, and microbials. FGNs can adsorb and concentrate nutrition factors including proteins from physiological media. This accelerates the formation of extracellular matrix, which eventually promotes cell colonization by providing a more beneficial microenvironment for cell adhesion and growth. Furthermore, FGNs can also interact with cocultured cells by physical or chemical stimulation, which significantly mediate their cellular signaling and biological performance. In this review, we elucidate FGNs-bioorganism interactions and summarize recent advancements on designing FGN-based two-dimensional and three-dimensional architectures as multifunctional biological platforms. We have also discussed the representative biological applications regarding these FGN-based bioactive architectures. Furthermore, the future perspectives and emerging challenges will also be highlighted. Due to the lack of comprehensive reviews in this emerging field, this review may catch great interest and inspire many new opportunities across a broad range of disciplines.

Interface-induced terahertz persistent photoconductance in rGO-gelatin flexible films

Light-induced difference terahertz (THz) spectroscopy is used to investigate the dielectric characteristics of reduced graphene oxide-gelatin (rGO-Gel) flexible films. RGO-Gel films are observed to exhibit positive photoconductance under 800 nm laser illumination, resulting in the modulation depth of the THz transmission up to 33.5%. Moreover, persistent photoconductance (PPC), which is a prolonged light-induced conducting behavior, has been observed to last as long as tens of seconds in rGO-Gel films. The PPC phenomenon is due to the electrons trapped in the defects of rGO and in the interface between rGO and gelatin, and is enhanced by the strong interaction between rGO (a p-type semiconductor) and gelatin (electron donors). This work holds potential for creating optoelectronic devices based on rGO-Gel films, such as optical modulators, switches, photodetectors, photosensors, and persistent photonic memory devices in the THz region.

A facile and viable approach to fabricate polyamide membranes functionalized with graphene oxide nanosheets

The covalent binding of GO nanosheets to a PA RO membrane was successfully achieved by reacting the primary amine functional groups of aminated GO (AGO) nanosheets with the unreacted acid chloride groups of the nascent PA membrane.

Tailoring Graphene Nanosheets for Highly Improved Dispersion Stability and Quantitative Assessment in Nonaqueous Solvent

Aggregation is a critical limitation for the practical application of graphene-based materials. Herein, we report that graphene oxide (GO) nanosheets chemically modified with ethanolamine (EA), ethylene glycol (EG), and sulfanilic acid (SA) demonstrate superior dispersion stability in organic solvents, specifically EG, based on the differences in their covalent chemistries. Functionalized GO was successfully dispersed in EG at a concentration of 9.0 mg mL(-1) (0.50 vol %), the highest dispersion concentration reported to date. Moreover, our study introduces a unique analytical method for the assessment of dispersion stability and successfully quantifies the instability index based on transmission profiles under centrifugation cycles. Interestingly, GO-EG and GO-EA exhibited highly improved dispersion stabilities approximately 96 and 48 times greater than that of GO in EG solvent, respectively. This finding highlights the critical role of surface functional groups in the enhancement of chemical affinity and miscibility in the surrounding media. We anticipate that the novel structural designs and unique tools presented in this study will further the understanding and application of chemically functionalized carbon materials.

Recent developments in the layer-by-layer assembly of polyaniline and carbon nanomaterials for energy storage and sensing applications. From synthetic aspects to structural and functional characterization

The construction of hybrid polymer-inorganic nanoarchitectures for electrochemical purposes based on the layer-by-layer assembly of conducting polymers and carbon nanomaterials has become increasingly popular over the last decade. This explosion of interest is primarily related to the increasing mastery in the design of supramolecular constructs using simple wet chemical approaches. Concomitantly, this continuous research activity paved the way to the rapid development of nanocomposites or "nanoblends" readily integrable into energy storage and sensing devices. In this sense, the layer-by-layer (LbL) assembly technique has allowed us to access three-dimensional (3D) multicomponent carbon-based network nanoarchitectures displaying addressable electrical, electrochemical and transport properties in which conducting polymers, such as polyaniline, and carbon nanomaterials, such as carbon nanotubes or nanographene, play unique roles without disrupting their inherent functions - complementary entities coexisting in harmony. Over the last few years the level of functional sophistication reached by LbL-assembled carbon-based 3D network nanoarchitectures, and the level of knowledge related to how to design, fabricate and optimize the properties of these 3D nanoconstructs have advanced enormously. This feature article presents and discusses not only the recent advances but also the emerging challenges in complex hybrid nanoarchitectures that result from the layer-by-layer assembly of polyaniline, a quintessential conducting polymer, and diverse carbon nanomaterials. This is a rapidly developing research area, and this work attempts to provide an overview of the diverse 3D network nanoarchitectures prepared up to now. The importance of materials processing and LbL integration is explored within each section and while the overall emphasis is on energy storage and sensing applications, the most widely-used synthetic strategies and characterization methods for "nanoblend" formation and performance evaluation are also presented.

Layer-by-Layer Self-Assembled Graphene Multilayers as Pt-Free Alternative Counter Electrodes in Dye-Sensitized Solar Cells

Low cost, charged, and large scale graphene multilayers fabricated from nitrogen-doped reduced graphene oxide N-rGO(+), nitrogen and sulfur codoped reduced graphene oxide NS-rGO(+), and undoped reduced graphene oxide rGO(-) were applied as alternative counter electrodes in dye-sensitized solar cells (DSSCs). The neat rGO-based counter electrodes were developed via two types of layer-by-layer (LBL) self-assembly (SA) methods: spin coating and spray coating methods. In the spin coating method, two sets of multilayer films were fabricated on poly(diallyldimethylammonium chloride) (PDDA)-coated fluorine-doped tin oxide (FTO) substrates using GO(-) combined with N-GO(+) followed by annealing and denoted as [rGO(-)/N-rGO(+)]n or with NS-GO(+) and denoted as [rGO(-)/NS-rGO(+)]n for counter electrodes in DSSCs. The DSSCs employing new types of counter electrodes exhibited ∼7.0% and ∼6.2% power conversion efficiency (PCE) based on ten bilayers of [rGO(-)/N-rGO(+)]10 and [rGO(-)/NS-rGO(+)]10, respectively. The DSSCs equipped with a blend of one bilayer of [rGO(-):N-rGO(+)] and [rGO(-):NS-rGO(+)] on PDDA-coated FTO substrates were prepared from a spray coating and showed ∼6.4% and ∼5.6% PCE, respectively. Thus, it was demonstrated that a combination of undoped, nitrogen-doped, and nitrogen and sulfur codoped reduced graphene oxides can be considered as potentially powerful Pt-free electrocatalysts and alternative electrodes in conventional photovoltaic devices.

Effect of pH on the structure and drug release profiles of layer-by-layer assembled films containing polyelectrolyte, micelles, and graphene oxide

Layer by layer (lbl) assembled multilayer thin films are used in drug delivery systems with attractive advantages such as unlimited selection of building blocks and free modification of the film structure. In this paper, we report the fundamental properties of lbl films constructed from different substances such as PS-b-PAA amphiphilic block copolymer micelles (BCM) as nano-sized drug vehicles, 2D-shaped graphene oxide (GO), and branched polyethylenimine (bPEI). These films were fabricated by successive lbl assembly as a result of electrostatic interactions between the carboxyl group of BCM and amine group of functionalized GO or bPEI under various pH conditions. We also compared the thickness, roughness, morphology and degree of adsorption of the (bPEI/BCM) films to those in the (GO/BCM) films. The results showed significant difference because of the distinct pH dependence of each material. In addition, drug release rates of the GO/BCM film were more rapid those of the (bPEI/BCM) film in pH 7.4 and pH 2 PBS buffer solutions. In (bPEI/BCM/GO/BCM) film, the inserted GO layers into bPEI/BCM multilayer induced rapid drug release. We believe that these materials &pH dependent film properties allow developments in the control of coating techniques for biological and biomedical applications.

Sheet Size-Induced Evaporation Behaviors of Inkjet-Printed Graphene Oxide for Printed Electronics

The size of chemically modified graphene nanosheets is a critical parameter that affects their performance and applications. Here, we show that the lateral size of graphene oxide (GO) nanosheets is strongly correlated with the concentration of graphite oxide present in the suspension as graphite oxide is exfoliated by sonication. The size of the GO nanosheets increased from less than 100 nm to several micrometers as the concentration of graphite oxide in the suspension was increased up to a critical concentration. An investigation of the evaporation behavior of the GO nanosheet solution using inkjet printing revealed that the critical temperature of formation of a uniform film, T(c), was lower for the large GO nanosheets than for the small GO nanosheets. This difference was attributed to the interactions between the two-dimensional structures of GO nanosheets and the substrate as well as the interactions among the GO nanosheets. Furthermore, we fabricated organic thin film transistors (OTFTs) using line-patterned reduced GO as electrodes. The OTFTs displayed different electrical performances, depending on the graphene sheet size. We believe that our new strategy to control the size of GO nanosheets and our findings about the colloidal and electrical properties of size-controlled GO nanosheets will be very effective to fabricate graphene based printed electronics.

Moving beyond flexible to stretchable conductive electrodes using metal nanowires and graphenes

Stretchable and/or flexible electrodes and their associated electronic devices have attracted great interest because of their possible applications in high-end technologies such as lightweight, large area, wearable, and biointegrated devices. In particular, metal nanowires and graphene derivatives are chosen for electrodes because they show low resistance and high mechanical stability. Here, we review stretchable and flexible soft electrodes by discussing in depth the intrinsic properties of metal NWs and graphenes that are driven by their dimensionality. We investigate these properties with respect to electronics, optics, and mechanics from a chemistry perspective and discuss currently unsolved issues, such as how to maintain high conductivity and simultaneous high mechanical stability. Possible applications of stretchable and/or flexible electrodes using these nanodimensional materials are summarized at the end of this review.

Preparation of Three-Dimensional Graphene Foams Using Powder Metallurgy Templates

A simple and scalable method which combines traditional powder metallurgy and chemical vapor deposition is developed for the synthesis of mesoporous free-standing 3D graphene foams. The powder metallurgy templates for 3D graphene foams (PMT-GFs) consist of particle-like carbon shells which are connected by multilayered graphene that shows high specific surface area (1080 m(2) g(-1)), good crystallization, good electrical conductivity (13.8 S cm(-1)), and a mechanically robust structure. The PMT-GFs did not break under direct flushing with DI water, and they were able to recover after being compressed. These properties indicate promising applications of PMT-GFs for fields requiring 3D carbon frameworks such as in energy-based electrodes and mechanical dampening.

Graphene-enhanced intermolecular interaction at interface between copper- and cobalt-phthalocyanines

Interfacial electronic structures of copper-phthalocyanine (CuPc), cobalt-phthalocyanine (CoPc), and graphene were investigated experimentally by using photoelectron spectroscopy. While the CuPc/graphene interface shows flat band structure and negligible interfacial dipole indicating quite weak molecule-substrate interaction, the CuPc/CoPc/graphene interface shows a large interfacial dipole and obvious energy level bending. Controlled experiments ruled out possible influences from the change in film structure of CuPc and pure π-π interaction between CoPc and CuPc. Analysis based on X-ray photoelectron spectroscopy and density functional theory reveals that the decrease in the work function for the CuPc/CoPc/graphene system is induced by the intermolecular interaction between CuPc and CoPc which is enhanced owning to the peculiar electronic properties at the CoPc-graphene interface.

Efficient Direct Reduction of Graphene Oxide by Silicon Substrate

Graphene has been studied for various applications due to its excellent properties. Graphene film fabrication from solutions of graphene oxide (GO) have attracted considerable attention because these procedures are suitable for mass production. GO, however, is an insulator, and therefore a reduction process is required to make the GO film conductive. These reduction procedures require chemical reducing agents or high temperature annealing. Herein, we report a novel direct and simple reduction procedure of GO by silicon, which is the most widely used material in the electronics industry. In this study, we also used silicon nanosheets (SiNSs) as reducing agents for GO. The reducing effect of silicon was confirmed by various characterization methods. Furthermore, the silicon wafer was also used as a reducing template to create a reduced GO (rGO) film on a silicon substrate. By this process, a pure rGO film can be formed without the impurities that normally come from chemical reducing agents. This is an easy and environmentally friendly method to prepare large scale graphene films on Si substrates.