Visible light- and dark-driven degradation of palm oil mill effluent (POME) over g-C3N4 and photo-rechargeable WO3

The investigations of real industrial wastewater, such as palm oil mill effluent (POME), as a recalcitrant pollutant remain a subject of global water pollution concern. Thus, this work introduced the preparation and modification of g-C3N4 and WO3 at optimum calcination temperature, where they were used as potent visible light-driven photocatalysts in the degradation of POME under visible light irradiation. Herein, g-C3N4-derived melamine and WO3 photocatalyst were obtained at different calcination temperatures in order to tune their light absorption ability and optoelectronics properties. Both photocatalysts were proven to have their distinct phases, crystallinity levels, and elements with increasing temperature, as demonstrated by the ultraviolet-visible spectroscopy (UV-Vis), X-ray diffraction analysis (XRD), thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) results. Significantly, g-C3N4 (580 °C) and WO3 (450 °C) unitary photocatalysts exhibited the highest removal efficiency of POME without dilution due to good crystallinity, extended light absorption, high separation, and less recombination efficiency of electron-hole pairs. Furthermore, surprisingly, the superior energy storage photocatalytic performance with outstanding stability by WO3 achieved an approximately 10% increment during darkness, compared with g-C3N4 under visible light irradiation. Moreover, it has been proven that the WO3 and g-C3N4 photocatalysts are desirable photocatalysts for various pollutant degradations, with excellent visible-light utilization and favorable energy storage application.

Heterostructured WO3-TiVO4 thin-film photocatalyst for efficient photoelectrochemical water splitting

Photoelectrochemical water splitting via solar irradiation has garnered significant interest due to its potential in large-scale renewable hydrogen production. Heterostructure materials have emerged as an effective strategy, demonstrating enhanced performance in photoelectrochemical water-splitting applications compared to individual photocatalysts. In this study, to augment the performance of sprayed TiVO4 thin films, a hydrothermally prepared WO3 underlayer was integrated beneath the spray pyrolised TiVO4 film. The consequent heterostructure demonstrated notable enhancements in optical, structural, microstructural attributes, and photocurrent properties. This improvement is attributed to the strategic deposition of WO3 underlayer, forming a heterostructure composite electrode. This led to a marked increase in photocurrent density for the WO3/TiVO4 photoanode, reaching a peak of 740 μA/cm2 at an applied potential of 1.23 V vs RHE, about nine-fold that of standalone TiVO4. Electrochemical impedance spectroscopy revealed a reduced semicircle for the heterostructure, indicating improved charge transfer compared to bare TiVO4. The heterostructure photoelectrode exhibited enhanced charge carrier conductivity at the interface and sustained stability over 3 h. The distinct attributes of heterostructure photoelectrode present significant opportunities for devising highly efficient sunlight-driven water-splitting systems.

Morphology-Controlled ZnO@ZnWO4 Hetero-Nanostructures for Efficient Photooxidation of Water in Near-Neutral pH

One-dimensional ZnO nanorods (NRs) have been extensively studied as photoanodes because of their unique optical properties, high electron mobility, and suitable band positions for water oxidation. However, their practical efficiency is often compromised by chemical instability during water oxidation and high carrier recombination rates. To overcome this issue, precise morphological control of ZnO@ZnWO4 core-shell structured photoanodes, featuring a ZnO core and a ZnWO4 shell was used. This was accomplished by depositing WO3 onto hydrothermally grown ZnO NRs using the thermal chemical vapor deposition process. The photoelectrochemical performance of ZnO@ZnWO4 with an optimized morphology outperforms that of pristine ZnO NRs. Systematic optical and electrochemical analyses of ZnO@ZnWO4 demonstrated that the enhancement is attributed to the enhanced charge transfer efficiency facilitated by the optimized ZnWO4 shells.

Minimizing CO2 emissions by photocatalytic CO2 reduction to CH3OH over Li2MnO3/WO3 heterostructures under visible illumination

Photocatalytic CO2 reduction to valuable fuels has proved to be a favourable process to produce renewable energy and reduce CO2 emissions, which mostly depends on designing effective photocatalysts with the rapid separation rate of charge carriers. In this contribution, mesoporous n-n heterojunction Li2MnO3/WO3 nanocomposites were designed via a simplistic sol-gel process for CO2 reduction utilizing visible illumination (λ > 420 nm). XRD and TEM measurements confirmed the synthesized Li2MnO3/WO3 nanocomposite is a monoclinic structure, and its particle size is 25 ± 5 nm. The obtained Li2MnO3/WO3 exhibited narrower bandgap energy (1.74 eV), larger surface area (212 m2g-1), exceedingly visible absorbing, and lower recombination of electron and hole. The yield of CH3OH was determined about 198, 871, 1140, 1550 and 1570 mmolg-1 for bare WO3 and 5%, 10%, 15% and 20% Li2MnO3/WO3 nanocomposites, respectively. These results evidenced that the 15% Li2MnO3/WO3 photocatalyst exhibited the best reduction ability compared to other nanocomposites. The CO2 reduction over 15% Li2MnO3/WO3 photocatalyst achieved a maximal CO2 conversion with the substantially boosted CH3OH, i.e., 1550 mmolg-1 after 9 h, which was enhanced 7.8 folds great than of WO3 NPs. Mesoporous Li2MnO3/WO3 nanocomposites, in comparison with bare WO3 NPs, created more active sites for facilitating CO2 and had a specific electric field to more effectively separate charge carriers. The Li2MnO3/WO3 photocatalyst has superior photostability during the continuous reduction of CO2 for 45 h with no remarkable decrease. The possible direct S-scheme mechanism for electron transfer over Li2MnO3/WO3 photocatalyst with the enhanced CO2 reduction ability was discussed. The present work demonstrates an avenue for building highly effective heterostructure photocatalysts in solar-energy-induced potential applications.

Key Strategies on Cu2O Photocathodes toward Practical Photoelectrochemical Water Splitting

Cuprous oxide (Cu2O) has been intensively in the limelight as a promising photocathode material for photoelectrochemical (PEC) water splitting. The state-of-the-art Cu2O photocathode consists of a back contact layer for transporting the holes, an overlayer for accelerating charge separation, a protection layer for prohibiting the photocorrosion, and a hydrogen evolution reaction (HER) catalyst for reducing the overpotential of HER, as well as a Cu2O layer for absorbing sunlight. In this review, the fundamentals and recent research progress on these components of efficient and durable Cu2O photocathodes are analyzed in detail. Furthermore, key strategies on the development of Cu2O photocathodes for the practical PEC water-splitting system are suggested. It provides the specific guidelines on the future research direction for the practical application of a PEC water-splitting system based on Cu2O photocathodes.

Improved Photoelectrochemical Performance of WO3/BiVO4 Heterojunction Photoanodes via WO3 Nanostructuring

WO3/BiVO4 heterojunction photoanodes can be efficiently employed in photoelectrochemical (PEC) cells for the conversion of water into molecular oxygen, the kinetic bottleneck of water splitting. Composite WO3/BiVO4 photoelectrodes possessing a nanoflake-like morphology have been synthesized through a multistep process and their PEC performance was investigated in comparison to that of WO3/BiVO4 photoelectrodes displaying a planar surface morphology and similar absorption properties and thickness. PEC tests, also in the presence of a sacrificial hole scavenger, electrochemical impedance analysis under simulated solar irradiation, and incident photon to current efficiency measurements highlighted that charge transport and charge recombination issues affecting the performance of the planar composite can be successfully overcome by nanostructuring the WO3 underlayer in nanoflake-like WO3/BiVO4 heterojunction electrodes.

Fabrication of Hematite Photoanode Consisting of (110)-Oriented Single Crystals

In this work, α-Fe2 O3 photoanode consisted of (110)-oriented α-Fe2 O3 single crystals were synthesized by a facile hydrothermal method. By using particular additive (C4 MimBF4 ) and regulation of hydrothermal reaction time, the Fe-25 consisted of a single-layer of highly crystalline (110)-oriented crystals with fewer grain boundaries, which was vertically grown on the substrate. As a result, the charge separation efficiency and photoelectrochemical (PEC) performance of Fe-25A (Fe-25 after dehydration treatment) have been greatly improved. Fe-25A yields a photocurrent of 1.34 mA cm-2 (1.23 V vs RHE) and an incident photon-to-current conversion efficiency (IPCE) of 31.95 % (380 nm). With the assistance of cobalt-phosphate water oxidation catalyst (Co-Pi), the PEC performance could be further improved by enhancing the holes transfer at electrode/electrolyte interface and inhibiting surface recombination. Fe-25A/Co-Pi yields a photocurrent of 2.67 mA cm-2 (1.23 V vs RHE) and IPCE value of 50.8 % (380 nm), which is 3.67 times and 2.39 times as that of Fe-2A/Co-Pi. Our work provides a simple method to fabricate highly efficient Fe2 O3 photoanodes consist of characteristic (110)-oriented single crystals with high crystallinity and high quality interface contact to enhance charge separation efficiencies.

Characterization and Comparison of WO3/WO3-MoO3 and TiO2/TiO2-ZnO Nanostructures for Photoelectrocatalytic Degradation of the Pesticide Imazalil

Tungsten oxide (WO3) and zinc oxide (ZnO) are n-type semiconductors with numerous applications in photocatalysis. The objective of this study was to synthesize and characterize different types of nanostructures (WO3, WO3-Mo, TiO2, and TiO2-ZnO) for a comparison of hybrid and pure nanostructures to use them as a photoanodes for photoelectrocatalytic degradation of emerging contaminants. With the aim of comparing the properties of both samples, field emission scanning electron microscopy (FE-SEM) and confocal laser-Raman spectroscopy were used to study the morphology, composition, and crystallinity, respectively. Electrochemical impedances, Mott-Schottky, and water splitting measurements were performed to compare the photoelectrochemical properties of photoanodes. Finally, the photoelectrocatalytic degradation of the pesticide Imazalil was carried out with the best optimized nanostructure (TiO2-ZnO).

Tandem cells for unbiased photoelectrochemical water splitting

Hydrogen is an essential energy carrier which will address the challenges posed by the energy crisis and climate change. Photoelectrochemical water splitting (PEC) is an important method for producing solar-powered hydrogen. The PEC tandem configuration harnesses sunlight as the exclusive energy source to drive both the hydrogen (HER) and oxygen evolution reactions (OER), simultaneously. Therefore, PEC tandem cells have been developed and gained tremendous interest in recent decades. This review describes the current status of the development of tandem cells for unbiased photoelectrochemical water splitting. The basic principles and prerequisites for constructing PEC tandem cells are introduced first. We then review various single photoelectrodes for use in water reduction or oxidation, and highlight the current state-of-the-art discoveries. Second, a close look into recent developments of PEC tandem cells in water splitting is provided. Finally, a perspective on the key challenges and prospects for the development of tandem cells for unbiased PEC water splitting are given.

Controllable Synthesis of N2-Intercalated WO3 Nanorod Photoanode Harvesting a Wide Range of Visible Light for Photoelectrochemical Water Oxidation

A highly efficient visible-light-driven photoanode, N2-intercalated tungsten trioxide (WO3) nanorod, has been controllably synthesized by using the dual role of hydrazine (N2H4), which functioned simultaneously as a structure directing agent and as a nitrogen source for N2 intercalation. The SEM results indicated that the controllable formation of WO3 nanorod by changing the amount of N2H4. The β values of lattice parameters of the monoclinic phase and the lattice volume changed significantly with the nW: nN2H4 ratio. This is consistent with the addition of N2H4 dependence of the N content, clarifying the intercalation of N2 in the WO3 lattice. The UV-visible diffuse reflectance spectra (DRS) of N2-intercalated exhibited a significant redshift in the absorption edge with new shoulders appearing at 470–600 nm, which became more intense as the nW:nN2H4 ratio increased from 1:1.2 and then decreased up to 1:5 through the maximum at 1:2.5. This addition of N2H4 dependence is consistent with the case of the N contents. This suggests that N2 intercalating into the WO3 lattice is responsible for the considerable red shift in the absorption edge, with a new shoulder appearing at 470−600 nm owing to formation of an intra-bandgap above the VB edges and a dopant energy level below the CB of WO3. The N2 intercalated WO3 photoanode generated a photoanodic current under visible light irradiation below 530 nm due to the photoelectrochemical (PEC) water oxidation, compared with pure WO3 doing so below 470 nm. The high incident photon-to-current conversion efficiency (IPCE) of the WO3-2.5 photoanode is due to efficient electron transport through the WO3 nanorod film.

Recent Advances in Self-Supported Semiconductor Heterojunction Nanoarrays as Efficient Photoanodes for Photoelectrochemical Water Splitting

Growth of semiconductor heterojunction nanoarrays directly on conductive substrates represents a promising strategy toward high-performance photoelectrodes for photoelectrochemical (PEC) water splitting. By controlling the growth conditions, heterojunction nanoarrays with different morphologies and semiconductor components can be fabricated, resulting in greatly enhanced light-absorption properties, stabilities, and PEC activities. Herein, recent progress in the development of self-supported heterostructured semiconductor nanoarrays as efficient photoanode catalysts for water oxidation is reviewed. Synthetic methods for the fabrication of heterojunction nanoarrays with specific compositions and structures are first discussed, including templating methods, wet chemical syntheses, electrochemical approaches and chemical vapor deposition (CVD) methods. Then, various heterojunction nanoarrays that have been reported in recent years based on particular core semiconductor scaffolds (e.g., TiO₂ , ZnO, WO₃ , Fe₂ O₃ , etc.) are summarized, placing strong emphasis on the synergies generated at the interface between the semiconductor components that can favorably boost PEC water oxidation. Whilst strong progress has been made in recent years to enhance the visible-light responsiveness, photon-to-O₂ conversion efficiency and stability of photoanodes based on heterojunction nanoarrays, further advancements in all these areas are needed for PEC water splitting to gain any traction alongside photovoltaic-electrochemical (PV-EC) systems as a viable and cost-effective route toward the hydrogen economy.

High-throughput exploration of activity and stability for identifying photoelectrochemical water splitting materials

The experimental high-throughput (HT) exploration for a suitable solar water splitting photoanode has greatly relied on photoactivity as the sole descriptor to identify a promising region within the searched composition space. Although activity is essential, it is not sufficient for describing the overall performance and excludes other pertinent criteria for photoelectrochemical (PEC) water splitting. Photostability in the form of (photo)electrocatalyst dissolution must be tracked to illustrate the intricate relation between activity and stability for multinary photoelectrocatalysts. To access these two important metrics simultaneously, an automated PEC scanning flow cell coupled to an inductively coupled plasma mass spectrometer (PEC-ICP-MS) was used to study an Fe-Ti-W-O thin film materials library. The results reveal an interrelation between composition, photocurrent density, and element-specific dissolution. These structure-activity-stability correlations can be represented using data science tools like principal component analysis (PCA) in addition to common data visualization approaches. This study demonstrates the importance of addressing two of the most important catalyst metrics (activity and stability) in a rapid and parallel fashion during HT experiments to adequately discover high-performing compositions in the multidimensional search space.

Increase in Photocurrent Density of WO3 Photoanode by Placing a Layer of an Ordered Array of Mesoporous WO3 Micropillars on Top of a WO3 Sheet Layer

A facile stamping method was developed to assemble ordered arrays of mesoporous WO₃ micropillars with uniform sizes, shapes, and lengths on F-doped tin oxide glass. Using this method, a series of WO₃ heterostructural bilayer photoanodes consisting of an array of m-μm long ordered mesoporous WO₃ micropillars at the top and the n-μm thick mesoporous WO₃ plain sheet layer at the bottom (denoted as m/n) were prepared. Among them 2.5/7.5 displayed a steady state photocurrent density of 3.6 mA cm^-2 at 1.23 V (vs RHE) under AM 1.5 (1 Sun), which is much higher than that of the plain 10-μm thick WO₃ sheet (2.5 mA cm^-2). This phenomenon occurs owing to the following six benefits: increases in charge carrier density, number of photogenerated electron, charge collection rate, thermodynamic feasibility for the vectorial charge transport from the outermost layer of the photoanode to the inner layer, the surface hydrophilicity, and the decrease in charge transfer resistance.

Properties, optimized morphologies, and advanced strategies for photocatalytic applications of WO3 based photocatalysts

The development of WO₃ based photocatalysts has gained considerable attention across the world, especially in the realm of environmental remediation and energy production. WO₃ has a band gap of 2.5- 2.7 eV that falls under the visible region and is thus a potential candidate to utilize in various photocatalytic processes. As an earth-abundant metal oxide, WO₃ discovered in 1976 displayed excellent electronic and morphological properties, good stability, and enhanced photoactivity with diverse crystal phases. Also, it unveils non-toxicity, high stability in drastic conditions, biocompatibility, low cost, excellent hole mobility (10 cm² V^-1s^-1), and tunable band gap. This review provides a comprehensive overview of the different properties of WO₃ inclusive of crystallographic, electrical, optical, thermoelectrical, and ferroelectric properties. The different morphologies of WO₃ based on dimensions were obtained by adopting different fabrication methods including inspecting their effects on the efficiency of WO₃. Numerous strategies to construct an ideal photocatalyst such as engineering crystal facets, surface defects, doping, heterojunction formation explaining specifically type-II, Z-scheme, and S-scheme mechanisms with addition to carbonaceous based WO₃ nanocomposites are summed up to explore the photocatalytic performance. The typical application of WO₃ is deliberated in detail involving the role and efficiency of WO₃ in pollutant degradation, CO₂ photoreduction, and water splitting. Besides, other applications of WO₃ as gas-sensor, bio-sensor, decomposition of VOCs, heavy metals ions adsorption, and antimicrobial property are also included. Moreover, the numerous aspects responsible for the high efficiency of WO₃-based nanocomposites with their challenges, opportunities, and future aspects are summarized. Hopefully, this review may inspire researchers to explore new ideas to boost the production of clean energy for the next generation.

Tungsten and molybdenum oxide nanostructures: two-dimensional layers and nanoclusters

W- and Mo-oxides form an interesting class of materials, featuring structural complexities, stoichiometric flexibility, and versatile physical and chemical properties that render them attractive for many applications in diverse fields of nanotechnologies. In nanostructured form, novel properties and functionalities emerge as a result of quantum size and confinement effects. In this topical review, W- and Mo-oxide nanosystems are examined with particular emphasis on two-dimensional (2D) layers and small molecular-type clusters. We focus on the epitaxial growth of 2D layers on metal single crystal surfaces and investigate their novel geometries and structures by a surface science approach. The coupling between the oxide overlayer and the metal substrate surface is a decisive element in the formation of the oxide structures and interfacial strain and charge transfer are shown to determine the lowest energy structures. Atomic structure models as determined by density functional theory (DFT) simulations are reported and discussed for various interface situations, with strong and weak coupling. Free-standing (quasi-)2D oxide layers, so-called oxide nanosheets, are attracting a growing interest recently in the applied research community because of their easy synthesis via wet-chemical routes. Although they consist typically of several atomic layers thick-not always homogeneous-platelet systems, their quasi-2D character induces a number of features that make them attractive for optoelectronic, sensor or biotechnological device applications. A brief account of recently published preparation procedures of W- and Mo-oxide nanosheets and some prototypical examples of proof of concept applications are reported here. (MO₃)₃(M = W, Mo) clusters can be generated in the gas phase in nearly monodisperse form by a simple vacuum sublimation technique. These clusters, interesting molecular-type structures by their own account, can be deposited on a solid surface in a controlled way and be condensed into 2D W- and Mo-oxide layers; solid-state chemical reactions with pre-deposited surface oxide layers to form 2D ternary oxide compounds (tungstates, molybdates) have also been reported. The clusters have been proposed as model systems for molecular studies of reactive centres in catalytic reactions. Studies of the catalysis of (MO₃)₃clusters in unsupported and supported forms, using the conversion of alcohols as model reactions, are discussed. Finally, we close with a brief outlook of future perspectives.

Exceptional Photocatalytic Activities of rGO Modified (B,N) Co-Doped WO3 , Coupled with CdSe QDs for One Photon Z-Scheme System: A Joint Experimental and DFT Study

Artificial Z-scheme, a tandem structure with two-step excitation process, has gained significant attention in energy production and environmental remediation. By effectively connecting and matching the band-gaps of two different photosystems, it is significant to utilize more photons for excellent photoactivity. Herein, a novel one-photon (same energy-two-photon) Z-scheme system is constructed between rGO modified boron-nitrogen co-doped-WO₃ , and coupled CdSe quantum dots-(QDs). The coctalyst-0.5%Rh_x Cr₂ O₃ (0.5RCr) modified amount-optimized sample 6%CdSe/1%rGO3%BN-WO₃ revealed an unprecedented visible-light driven overall-water-splitting to produce ≈51 µmol h^-1 g^-1 H₂ and 25.5 µmol h^-1 g^-1 O₂ , and it remained unchanged for 5 runs in 30 h. This superior performance is ascribed to the one-photon Z-scheme, which simultaneously stimulates a two photocatalysts system, and enhanced charge separation as revealed by various spectroscopy techniques. The density-functional theory is further utilized to understand the origin of this performance enhancement. This work provides a feasible strategy for constructing an efficient one-photon Z-scheme for practical applications.

Molecular design of heterogeneous electrocatalysts using tannic acid-derived metal-phenolic networks

Electrochemistry could play a critical role in the transition to a more sustainable society by enabling the carbon-neutral production and use of various chemicals as well as efficient use of renewable energy resources. A prerequisite for the practical application of various electrochemical energy conversion and storage technologies is the development of efficient and robust electrocatalysts. Recently, molecularly designed heterogeneous catalysts have drawn great attention because they combine the advantages of both heterogeneous solid and homogeneous molecular catalysts. In particular, recently emerged metal-phenolic networks (MPNs) show promise as electrocatalysts for various electrochemical reactions owing to their unique features. They can be easily synthesized under mild conditions, making them eco-friendly, form uniform and conformal thin films on various kinds of substrates, accommodate various metal ions in a single-atom manner, and have excellent charge-transfer ability. In this minireview, we summarize the development of various MPN-based electrocatalysts for diverse electrochemical reactions, such as the hydrogen evolution reaction, the oxygen evolution reaction, the CO₂ reduction reaction, and the N₂ reduction reaction. We believe that this article provides insight into molecularly designable heterogeneous electrocatalysts based on MPNs and guidelines for broadening the applications of MPNs as electrocatalysts.

Improved Photocatalytic Water Splitting Activity of Highly Porous WO3 Photoanodes by Electrochemical H+ Intercalation

WO3 photoanodes are widely used in photoelectrochemical catalysis, but typically the as-synthesized material is annealed before application. It is therefore desirable to explore less energy-intensive treatments. In this study, WO3 films of up to 3.9 μm thickness were obtained by galvanostatic anodization of tungsten foil in a neutral-pH Na2SO4 and NaF electrolyte, also containing a NaH2PO2 additive (to suppress O2 accumulation on the pore walls). Additionally, the WO3 photoanodes were modified by applying a cathodic reduction (H+ intercalation) and anodic activation treatment in-situ. XPS spectra revealed that intercalation modifies WO3 films; the amount of W5+-O and O-vacancy bonds was increased. Furthermore, subsequent activation leads to a decrease of the W5+ signal, but the amount of O-vacancy bonds remains elevated. The as-prepared and reduced (intercalated & activated) films were tested as OER photoanodes in acidic 0.1 M Na2SO4 media, under illumination with a 365 nm wavelength LED. It was observed that thinner films generated larger photocurrents. The peculiarities detected by XPS for reduced films correlate well with their improved photocatalytic activity. Photo-electrochemical impedance and intensity modulated photocurrent spectroscopies were combined with steady-state measurements in order to elucidate the effects of H+ intercalation on photoelectrochemical performance. The reduction results in films with enhanced photoexcited charge carrier generation/separation, improved conductivity, and possibly even suppressed bulk recombination. Thus, the intercalation & activation adopted in this study can be reliably used to improve the overall activity of as-synthesized WO3 photoanodes, and particularly of those that are initially poorly photoactive.

BiVO4 Ceramic Photoanode with Enhanced Photoelectrochemical Stability

Monoclinic bismuth vanadate (BiVO₄) is an attractive material with which to fabricate photoanodes due to its suitable band structure and excellent photoelectrochemical (PEC) performance. However, the poor PEC stability originating from its severe photo-corrosion greatly restricts its practical applications. In this paper, pristine and Mo doped BiVO₄ ceramics were prepared using the spark plasma sintering (SPS) method, and their photoelectrochemical properties as photoanodes were investigated. The as-prepared 1% Mo doped BiVO₄ ceramic (Mo-BVO (C)) photoanode exhibited enhanced PEC stability compared to 1% Mo doped BiVO₄ films on fluorine doped Tin Oxide (FTO) coated glass substrates (Mo-BVO). Mo-BVO (C) exhibited a photocurrent density of 0.54 mA/cm² and remained stable for 10 h at 1.23 V vs. reversible hydrogen electrode (RHE), while the photocurrent density of the Mo-BVO decreased from 0.66 mA/cm² to 0.11 mA/cm² at 1.23 V vs. RHE in 4 h. The experimental results indicated that the enhanced PEC stability of the Mo-BVO (C) could be attributed to its higher crystallinity, which could effectively inhibit the dissociation of vanadium in BiVO₄ during the PEC process. This work may illustrate a novel ceramic design for the improvement of the stability of BiVO₄ photoanodes, and might provide a general strategy for the improvement of the PEC stability of metal oxide photoanodes.

Effect of morphology on the photoelectrochemical performance of nanostructured Cu2O photocathodes

Cu₂O is a promising earth-abundant semiconductor photocathode for sunlight-driven water splitting. Characterization results are presented to show how the photocurrent density (J_ph), onset potential (E_onset), band edges, carrier density (N_A), and interfacial charge transfer resistance (R_ct) are affected by the morphology and method used to deposit Cu₂O on a copper foil. Mesoscopic and planar morphologies exhibit large differences in the values ofN_AandR_ct. However, these differences are not observed to translate to other photocatalytic properties of Cu₂O. Mesoscopic and planar morphologies exhibit similar bandgap (e.g.) and flat band potential (E_fb) values of 1.93 ± 0.04 eV and 0.48 ± 0.06 eV respectively.E_onsetof 0.48 ± 0.04 eV obtained for these systems is close to theE_fbindicating negligible water reduction overpotential. Electrochemically deposited planar Cu₂O provides the highest photocurrent density of 5.0 mA cm^-2at 0 V vs reversible hydrogen electrode (RHE) of all the morphologies studied. The photocurrent densities observed in this study are among the highest reported values for bare Cu₂O photocathodes.

The design of high performance photoanode of CQDs/TiO2/WO3 based on DFT alignment of lattice parameter and energy band, and charge distribution

Photoanode is the key issue for photoelectrocatalytic (PEC) water splitting and organics degradation. However, it always faces several restrictions including severe photocorrosion, low charge separation and transfer efficiencies, poor visible light harvesting, and sluggish interfacial reaction kinetics, which often required a variety of modifications with only low improvements achieved. Herein, a high performance CQDs/TiO₂/WO₃ photoanode was designed on the basis of density function theory (DFT) alignment of lattice parameters and energy band, and charge distribution. The TiO₂/WO₃ heterojunction can abate photocorrosion through the hetero-epitaxial growth of TiO₂ (001) on WO₃ (002) for the lattice mismatch <3% eliminating dangling bonds, with high corrosion resistance and photostability of TiO₂. As the built-in field constructed by a staggered band alignment structure with the valence band offset (VBO) of 0.51 eV, the photogenerated carriers transfer and separation are promoted dramatically. Through the DFT calculations, the sunlight absorption wavelength can be extended, and the interfacial reaction kinetics can be expedited with the modification of carbon quantum dots (CQDs) on TiO₂/WO₃, due to the narrower bandgap (E_g) and the accumulation of electrons at TiO₂ side. The DFT designed CQDs/TiO₂/WO₃ photoanode significantly increase photocurrent density from 0.90 to 2.03 mA cm^-2 at 1.23 V, charge separation efficiency from 56.3 to 79.2% and charge injection efficiency from 51.2 to 70.4%, and extend light absorption edge from 455 to 463 nm over pristine WO₃, with better photostability and lower holes-to-water resistance.

Acid-Resistant BiVO4 Photoanodes: Insolubility Control by Solvents and Weak W Diffusion in the Lattice

We have revealed for the first time that BiVO₄ photoanodes can be used even in strong acid media by mixing organic solvents into the electrolyte and depositing multilayers with a WO₃ bottom layer. In general, the BiVO₄ photoanodes are photocorrosive, especially in acid solutions. However, this shortcoming has been overcome using a combination of the two aforementioned modifications. We deduced that the contribution of each mixing organic solvent for the anti-photocorrosion of BiVO₄ in sulfuric acid solutions can be evaluated on the basis of a new empirical indicator that incorporates molecular density, the Hansen solubility parameter, and molecular polarizability. Acetone and tert-butyl alcohol were especially promising solvents for stabilizing BiVO₄ in acid media. We confirmed that the mixed organic solvents stabilized surface-emergent Bi oxide species as a passivation layer, which was generated via multilayering with a WO₃ bottom layer. During heat treatment in the fabrication process, W weakly diffused into the BiVO₄ layer and a Bi oxide layer was formed on the outermost surface because of the Bi segregation that arose from the charge compensation between W⁶⁺ and V⁵⁺ in the BiVO₄ lattice. The surface Bi oxide layer, which was protected by the mixed organic solvents, steadily served as a passivation layer for anti-photocorrosion of the underlying BiVO₄ layer. We have confirmed that the BiVO₄/WO₃ photoanodes in acetone-mixed aqueous sulfuric acid solution reliably functioned for a photoelectrochemical reaction under simulated sunlight illumination, and photoelectrochemical production of S₂O₈^2- ions was confirmed under light irradiation at λ > 480 nm. These results suggest that the BiVO₄-based photoanodes have significant potential for use in acid media in conjunction with very straightforward modifications.

Advanced materials and technologies for supercapacitors used in energy conversion and storage: a review

Supercapacitors are increasingly used for energy conversion and storage systems in sustainable nanotechnologies. Graphite is a conventional electrode utilized in Li-ion-based batteries, yet its specific capacitance of 372 mA h g−1 is not adequate for supercapacitor applications. Interest in supercapacitors is due to their high-energy capacity, storage for a shorter period and longer lifetime. This review compares the following materials used to fabricate supercapacitors: spinel ferrites, e.g., MFe2O4, MMoO4 and MCo2O4 where M denotes a transition metal ion; perovskite oxides; transition metals sulfides; carbon materials; and conducting polymers. The application window of perovskite can be controlled by cations in sublattice sites. Cations increase the specific capacitance because cations possess large orbital valence electrons which grow the oxygen vacancies. Electrodes made of transition metal sulfides, e.g., ZnCo2S4, display a high specific capacitance of 1269 F g−1, which is four times higher than those of transition metals oxides, e.g., Zn–Co ferrite, of 296 F g−1. This is explained by the low charge-transfer resistance and the high ion diffusion rate of transition metals sulfides. Composites made of magnetic oxides or transition metal sulfides with conducting polymers or carbon materials have the highest capacitance activity and cyclic stability. This is attributed to oxygen and sulfur active sites which foster electrolyte penetration during cycling, and, in turn, create new active sites.

The effect of nanoparticulate PdO co-catalysts on the faradaic and light conversion efficiency of WO3 photoanodes for water oxidation

WO3 photoanodes offer rare stability in acidic media, but are limited by their selectivity for oxygen evolution over parasitic side reactions, when employed in photoelectrochemical (PEC) water splitting. Herein, this is remedied via the modification of nanostructured WO3 photoanodes with surface decorated PdO as an oxygen evolution co-catalyst (OEC). The photoanodes and co-catalyst particles are grown using an up-scalable aerosol assisted chemical vapour deposition (AA-CVD) route, and their physical properties characterised by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HR-TEM) and UV-vis absorption spectroscopy. Subsequent PEC and transient photocurrent (TPC) measurements showed that the use of a PdO co-catalyst dramatically increases the faradaic efficiency (FE) of water oxidation from 52% to 92%, whilst simultaneously enhancing the photocurrent generation and charge extraction rate. The Pd oxidation state was found to be critical in achieving these notable improvements to the photoanode performance, which is primarily attributed to the higher selectivity towards oxygen evolution when PdO is used as an OEC and the formation of a favourable junction between WO3 and PdO, that drives band bending and charge separation.

Rapid and Low-Temperature Molecular Precursor Approach toward Ternary Layered Metal Chalcogenides and Oxides: Mo1-x W x S2 and Mo1-x W x O3 Alloys (0 ≤ x ≤ 1)

Metal sulfide and metal oxide alloys of the form Mo_1-x W _x S₂ and Mo_1-x W _x O₃ (0 ≤ x ≤ 1) are synthesized with varying nominal stoichiometries (x = 0, 0.25, 0.50, 0.75, and 1.0) by thermolysis of the molecular precursors MoL₄ and WS(S₂)L₂ (where L = S₂CNEt₂) in tandem and in various ratios. Either transition-metal dichalcogenides or transition-metal oxides can be produced from the same pair of precursors by the choice of reaction conditions; metal sulfide alloys of the form Mo_1-x W _x S₂ are produced in an argon atmosphere, while the corresponding metal oxide alloys Mo_1-x W _x O₃ are produced in air, both under atmospheric pressure at 450 °C and for only 1 h. Changes in Raman spectra and in powder X-ray diffraction patterns are observed across the series of alloys, which confirm that alloying is successful in the bulk materials. For the oxide materials, we show that the relatively complicated diffraction patterns are a result of differences in the tilt angle of MO₆ octahedra within three closely related unit cell types. Alloying of Mo and W in the products is characterized at the microscale and nanoscale by scanning electron microscopy-energy-dispersive X-ray spectroscopy (EDX) and scanning transmission electron microscopy-EDX spectroscopy, respectively.

Photodesorption mechanism of water on WO3(001) - a combined embedded cluster, computational intelligence and wave packet approach

In this work we investigate the mechanism of photodesorption of water from a WO3(001) surface by theoretical calculations, applying an embedded cluster model. Using the CASSCF method, we have calculated both the ground state as well as the energetically preferred charge-transfer state in three degrees of freedom of the water molecule on the surface. The calculated potential energy surfaces were afterwards fitted with a neural network optimized by a genetic algorithm. A final quantum dynamic wave packet study provided insight into the photodesorption mechanism.

Boosting the Activity and Stability of Copper Tungsten Nanoflakes toward Solar Water Oxidation by Iridium-Cobalt Phosphates Modification

Severe interfacial electron–hole recombination greatly limits the performance of CuWO4 photoanode towards the photoelectrochemical (PEC) oxygen evolution reaction (OER). Surface modification with an OER cocatalyst can reduce electron–hole recombination and thus improve the PEC OER performance of CuWO4. Herein, we coupled CuWO4 nanoflakes (NFs) with Iridium–cobalt phosphates (IrCo-Pi) and greatly improved the photoactivity of CuWO4. The optimized photocurrent density for CuWO4/IrCo-Pi at 1.23 V vs. reversible hydrogen electrode (RHE) rose to 0.54 mA∙cm−2, a ca. 70% increase over that of bare CuWO4 (0.32 mA∙cm−2). Such improved photoactivity was attributed to the enhanced hole collection efficiency, which resulted from the reduced charge-transfer resistance via IrCo-Pi modification. Moreover, the as-deposited IrCo-Pi layer well coated the inner CuWO4 NFs and effectively prevented the photoinduced corrosion of CuWO4 in neutral potassium phosphate (KPi) buffer solution, eventually leading to a superior stability over the bare CuWO4. The facile preparation of IrCo-Pi and its great improvement in the photoactivity make it possible to design an efficient CuWO4/cocatalyst system towards PEC water oxidation.

Type-II Heterostructure of ZnO and Carbon Dots Demonstrates Enhanced Photoanodic Performance in Photoelectrochemical Water Splitting

Hydrogen evolution through ecofriendly photoelectrochemical (PEC) water splitting is considered to be one of the most cost-effective and desirable methods for meeting ever-growing energy demands. However, the low photoconversion efficiency limits the practical applicability of PEC water splitting. To develop an efficient photoelectrode, here the morphology of ZnO is tuned from 0D to 3D. It is observed that vertically grown 2D nanosheets outperform other morphologies in PEC water splitting by generating nearly 0.414 mA cm^-2 at 0 V vs Ag/AgCl. Furthermore, these perpendicularly developed 2D nanosheets of ZnO are sensitized by metal-free carbon (C) dots to improve the photoconversion efficiency of ZnO. The prepared ZnO/C dots work as an effective photoanode, which can produce a 0.831 mA cm^-2 photocurrent density upon application of 0 V vs Ag/AgCl under constant illumination, which is 2 times higher than that of bare ZnO. The enhanced PEC performance of ZnO/C dots is confirmed by the photoconversion efficiency (η). The ZnO/C dots exhibit a 2-fold-higher photoconversion efficiency (η) compared to that of ZnO. Additionally, the enhancement in PEC activity of ZnO/C dots is attributed to the higher carrier concentrations in the heterostructure. Bare ZnO has a 1.77 × 10²⁰ cm^-3 carrier density, which becomes 3.70 × 10²⁰ cm^-3 after sensitization with C dots. Enhanced carrier density successively leads to higher PEC water splitting efficiency. Band alignments of ZnO and C dots indicate the creation of the type-II heterostructure, which facilitates successful charge transportation among C dots and ZnO, producing a charge-carrier separation. Two-dimensional sheets of ZnO and ZnO/C dots exhibit appreciable stability under continuous illumination for 1 and 2 h, respectively.

Photoinduced anisotropic distortion as the electron trapping site of tungsten trioxide by ultrafast W L1-edge X-ray absorption spectroscopy with full potential multiple scattering calculations

Understanding the excited state of photocatalysts is significant to improve their activity for water splitting reaction. X-ray absorption fine structure (XAFS) spectroscopy in X-ray free electron lasers (XFEL) is a powerful method to address dynamic changes in electronic states and structures of photocatalysts in the excited state in ultrafast short time scales. The ultrafast atomic-scale local structural change in photoexcited WO₃ was observed by W L₁ edge XAFS spectroscopy using an XFEL. An anisotropic local distortion around the W atom could reproduce well the spectral features at a delay time of 100 ps after photoexcitation based on full potential multiple scattering calculations. The distortion involved the movement of W to shrink the shortest W-O bonds and elongate the longest one. The movement of the W atom could be explained by the filling of the d_xy and d_zx orbitals, which were originally located at the bottom of the conduction band with photoexcited electrons.

Designing of WO3@Co3O4 Heterostructures to Enhance Photoelectrochemical Performances

Heterostructured photocatalysts are superior to single photocatalysts because they offer better charge separation and broaden light harnessing abilities. Although WO₃ is considered an oxygen-evolving photocatalyst with decent stability and proper band gap, its lower photocatalytic efficiency is ascribed to high charge recombination. In this research, a WO₃@Co₃O₄ heterostructure reduced the recombination of photocatalytic charges and extended light absorption abilities, resulting in improved photocatalytic activity. The presence of Co₃O₄ nanoparticles improved light absorption and charge transfer of tungsten oxide films for photoelectrochemical reactions. For photoelectrochemical water oxidation, WO₃@Co₃O₄ nanostructures generated a photocurrent 20 times higher than that of pure WO₃. Both electrodeposition and sol gel techniques were utilized to synthesize the WO₃@Co₃O₄ photoelectrode. Scanning electron microscopy and X-ray diffraction were used to characterize the formation of the above photocatalyst. A photocurrent study was done to investigate the charge separation mechanism to explain the enhanced photocatalytic activity.

Photoelectrocatalytic Hydrogen Production Using a TiO2/WO3 Bilayer Photocatalyst in the Presence of Ethanol as a Fuel

Photoelectrocatalytic hydrogen production was studied by using a photoelectrochemical cell where the photoanode was made by depositing on FTO electrodes either a nanoparticulate WO3 film alone or a bilayer film made of nanoparticulate WO3 at the bottom covered with a nanoparticulate TiO2 film on the top. Both the electric current and the hydrogen produced by the photoelectrocatalysis cell substantially increased by adding the top titania layer. The presence of this layer did not affect the current-voltage characteristics of the cell (besides the increase of the current density). This was an indication that the flow of electrons in the combined semiconductor photoanode was through the WO3 layer. The increase of the current was mainly attributed to the passivation of the surface recombination sites on WO3 contributing to the limitation of charge recombination mechanisms. In addition, the top titania layer may have contributed to photon absorption by back scattering of light and thus by enhancement of light absorption by WO3. Relatively high charge densities were recorded, owing both to the improvement of the photoanode by the combined photocatalyst and to the presence of ethanol as the sacrificial agent (fuel), which affected the recorded current by “current doubling” phenomena. Hydrogen was produced under electric bias using a simple cathode electrode made of carbon paper carrying carbon black as the electrocatalyst. This electrode gave a Faradaic efficiency of 58% for hydrogen production.

Cooperative Catalytic Behavior of SnO2 and NiWO4 over BiVO4 Photoanodes for Enhanced Photoelectrochemical Water Splitting Performance

n-BiVO4 is a favorable photoelectrode candidate for a photoelectrochemical (PEC) water splitting reaction owing to its suitable energy level edge locations for an oxygen evolution reaction. On the other hand, the sluggish water oxidation kinetics of BiVO4 photoanodes when used individually make it necessary to use a hole blocking layer as well as water oxidation catalysts to overcome the high kinetic barrier for the PEC water oxidation reaction. Here, we describe a very simple synthetic strategy to fabricate nanocomposite photoanodes that synergistically address both of these critical limitations. In particular, we examine the effect of a SnO2 buffer layer over BiVO4 films and further modify the photoanode surface with a crystalline nickel tungstate (NiWO4) nanoparticle film to boost PEC water oxidation. When NiWO4 is incorporated over BiVO4/SnO2 films, the PEC performance of the resultant triple-layer NiWO4/BiVO4/SnO2 films for the oxygen evolution reaction (OER) is further improved. The enhanced performance for the PEC OER is credited to the synergetic effect of the individual layers and the introduction of a SnO2 buffer layer over the BiVO4 film. The optimized NiWO4/BiVO4/SnO2 electrode demonstrated both enriched visible light absorption and achieves charge separation and transfer efficiencies of 23% and 30%, respectively. The photoanodic current density for the OER on optimized NiWO4/BiVO4/SnO2 photoanode shows a maximum photocurrent of 0.93 mA/cm2 at 1.23 V vs. RHE in a phosphate buffer solution (pH~7.5) under an AM1.5G solar simulator, which is an incredible five-fold and two-fold enhancement compared to its parent BiVO4 photoanode and BiVO4/SnO2 photoanodes, respectively. Further, the incorporation of the NiWO4 co-catalyst over the BiVO4/SnO2 film increases the interfacial electron transfer rate across the composite/solution interface.

Enhanced Photoelectrochemical Performance of WO3 -Based Composite Photoanode Coupled with Carbon Quantum Dots and NiFe Layered Double Hydroxide

An attractive photoanode material, WO₃ , has suffered from its limited visible-light absorption and sluggish surface reaction kinetics, as well as poor stability in neutral electrolytes. Herein, a NiFe/CQD/WO₃ composite photoanode was designed and fabricated, with loading of carbon quantum dots (CQDs) and electrodeposition of NiFe layered double hydroxide. The NiFe/CQD/WO₃ photoanode obtained a photocurrent density of 1.43 mA cm^-2 at 1.23 V vs. reversible hydrogen electrode, which is approximately three times higher than that of bare WO₃ . During the test period of 3 h, the stability of WO₃ was improved substantially after the loading of cocatalysts. Furthermore, mechanistic insights of the favored band structure and beneficial charge-transfer pathway elucidate the high photoelectrochemical performance of the NiFe/CQD/WO₃ composite photoanode.

Insight into the Kinetic Influence of Oxygen Vacancies on the WO3 Photoanodes for Solar Water Oxidation

Improvements to solar water oxidation performance for WO₃ photoanodes due to oxygen vacancies have in general been ascribed to thermodynamic effects. Detailed insights into the water oxidation kinetics for WO₃ photoanodes with oxygen vacancies are still lacking. Here, our experimental and computational investigations revealed that the water oxidation pathway on WO₃ photoanodes with oxygen vacancies is more inclined to follow the four-hole pathway. This finding reasonably explained the common observations of higher faradaic efficiency for oxygen evolution, better stability, and faster kinetics for water oxidation usually achieved on the WO₃ photoanodes with oxygen vacancies.

All-Solution-Processed WO3/BiVO4 Core-Shell Nanorod Arrays for Highly Stable Photoanodes

Tungsten oxide (WO₃) and bismuth vanadate (BiVO₄) are one of the most attractive combinations to construct an efficient heterojunction for photoelectrochemical (PEC) applications. Here, we report an all-solution-processed WO₃/BiVO₄ heteronanostructure photoanode with highly enhanced photoactivity and stability for sustainable energy production. The vertically aligned WO₃ nanorods were synthesized on a fluorine-doped tin oxide/glass substrate by the hydrothermal method without a seed layer and BiVO₄ was deposited by pulsed electrodeposition for conformal coating. Owing to the long diffusion lengths of charge carriers in the WO₃ nanorods, the ability to absorb the wider range of wavelengths, and appropriate band-edge positions of the WO₃/BiVO₄ heterojunction for spontaneous PEC reaction, the optimum WO₃/BiVO₄ photoanode has a photocurrent density of 4.15 mA/cm² at 1.23 V versus RHE and an incident-photon-to-current efficiency of 75.9% at 430 nm under front illumination, which are a double and quadruple those of pristine WO₃ nanorod arrays, respectively. Our work suggests an environment-friendly and low-cost all-solution process route to synthesize high-quality photoelectrodes.