Self-Assembled Preparation of Porous Nickel Phosphide Superparticles with Tunable Phase and Porosity for Efficient Hydrogen Evolution

Self-assembly of colloidal nanoparticles enables the easy building of assembly units into higher-order structures and the bottom-up preparation of functional materials. Nickel phosphides represent an important group of catalysts for hydrogen evolution reaction (HER) from water splitting. In this paper, the preparation of porous nickel phosphide superparticles and their HER efficiencies are reported. Ni and Ni2P nanoparticles are self-assembled into binary superparticles via an oil-in-water emulsion method. After annealing and acid etching, the as-prepared Ni-Ni2P binary superparticles change into porous nickel phosphide superparticles. The porosity and crystalline phase of the superparticles can be tuned by adjusting the ratio of Ni and Ni2P nanoparticles. The resulting porous superparticles are effective in driving HER under acidic conditions, and the modulation of porosity and phase further optimize the electrochemical performance. The prepared Ni3P porous superparticles not only possess a significantly enhanced specific surface area compared to solid Ni-Ni2P superparticles but also exhibit an excellent HER efficiency. The calculations based on the density functional theories show that the (110) crystal facet exhibits a relatively lower Gibbs free energy of hydrogen adsorption. This work provides a self-assembly approach for the construction of porous metal phosphide nanomaterials with tunable crystalline phase and porosity.

Structural interactions in polymer-stabilized magnetic nanocomposites

Superparamagnetic iron oxide nanoparticles (SPIONs) have attracted significant attention because of their nanoscale magnetic properties. SPION aggregates may afford emergent properties, resulting from dipole-dipole interactions between neighbors. Such aggregates can display internal order, with high packing fractions (>20%), and can be stabilized with block co-polymers (BCPs), permitting design of tunable composites for potential nanomedicine, data storage, and electronic sensing applications. Despite the routine use of magnetic fields for aggregate actuation, the impact of those fields on polymer structure, SPION ordering, and magnetic properties is not fully understood. Here, we report that external magnetic fields can induce ordering in SPION aggregates that affect their structure, inter-SPION distance, magnetic properties, and composite Tg. SPION aggregates were synthesized in the presence or absence of magnetic fields or exposed to magnetic fields post-synthesis. They were characterized using transmission electron microscopy (TEM), small angle X-ray scattering (SAXS), superconducting quantum interference device (SQUID) analysis, and differential scanning calorimetry (DSC). SPION aggregate properties depended on the timing of field application. Magnetic field application during synthesis encouraged preservation of SPION chain aggregates stabilized by polymer coatings even after removal of the field, whereas post synthesis application triggered subtle internal reordering, as indicated by increased blocking temperature (TB), that was not observed via SAXS or TEM. These results suggest that magnetic fields are a simple, yet powerful tool to tailor the structure, ordering, and magnetic properties of polymer-stabilized SPION nanocomposites.

Versatile Mesoporous Microblocks Prepared by Pattern-Induced Cracking of Colloidal Films

Mesoporous microparticles have the potential to be used in various fields, such as energy generation, sensing, and the environmental field. Recently, the process of making homogeneous microparticles in an economical and environmentally friendly way has gained much attention. Herein, rectangular mesoporous microblocks of various designs are produced by manipulating the fragmentation of colloidal films consisting of micropyramids while controlling the notch angles of pyramidal edges. During calcination of the colloidal films, cracks are generated in the valleys of micropyramids acting as notches, and the angle of notches can be controlled by the prepattern underneath the micropyramids. By changing the location of notches with sharp angles, the shape of microblocks can be controlled with excellent uniformity. After detaching the microblocks from substrates, mesoporous microparticles of various sizes with multiple functions are easily produced. This study demonstrates anti-counterfeiting functions by encoding the rotation angles of rectangular microblocks of various sizes. In addition, the mesoporous microparticles can be utilized for separating desired chemicals mixed with chemicals of different charges. The method of fabricating size-tunable functionalized mesoporous microblocks can be a platform technology to prepare special films and catalysts and for environmental applications.

Radioluminescent Cu-Au Metal Nanoclusters: Synthesis and Self-Assembly for Efficient X-ray Scintillation and Imaging

Zero-dimensional (0D) scintillation materials have drawn tremendous attention due to their inherent advantages in the fabrication of flexible high-energy radiation scintillation screens by solution processes. Although considerable progress has been made in the development of 0D scintillators, such as the current leading lead-halide perovskite nanocrystals and quantum dots, challenges still persist, including potential issues with self-absorption, air stability, and eco-friendliness. Here, we present a strategy to overcome those limitations by synthesis and self-assembly of a new class of scintillators based on metal nanoclusters. We demonstrate the gram-scale synthesis of an atomically precise nanocluster with a Cu-Au alloy core exhibiting high phosphorescence quantum yield, aggregation-induced emission enhancement (AIEE) behavior, and intense radioluminescence. By controlling solvent interactions, the AIEE-active nanoclusters were self-assembled into submicron spherical superparticles in solution, which we exploited as a novel building block for flexible particle-deposited scintillation films with high-resolution X-ray imaging performance. This work reveals metal nanoclusters and their self-assembled superstructures as a promising class of scintillators for practical applications in high-energy radiation detection and imaging.

From Meso to Macro: Controlling Hierarchical Porosity in Supraparticle Powders

A drying droplet containing colloidal particles can consolidate into a spherical assembly called a supraparticle. Such supraparticles are inherently porous due to the spaces between the constituent primary particles. Here, the emergent, hierarchical porosity in spray-dried supraparticles is tailored via three distinct strategies acting at different length scales. First, mesopores (<10 nm) are introduced via the primary particles. Second, the interstitial pores are tuned from the meso- (35 nm) to the macro scale (250 nm) by controlling the primary particle size. Third, defined macropores (>100 nm) are introduced via templating polymer particles, which can be selectively removed by calcination. Combining all three strategies creates hierarchical supraparticles with fully tailored pore size distributions. Moreover, another level of the hierarchy is added by fabricating supra-supraparticles, using the supraparticles themselves as building blocks, which provide additional pores with micrometer dimensions. The interconnectivity of the pore networks within all supraparticle types is investigated via detailed textural and tomographic analysis. This work provides a versatile toolbox for designing porous materials with precisely tunable, hierarchical porosity from the meso- (3 nm) to the macroscale (≈10 µm) that can be utilized for applications in catalysis, chromatography, or adsorption.

Rapid controllable synthesis of branched Au superparticles: formation mechanism of toggling the growth mode and their applications in optical broadband absorption

We develop a tunable, ultrafast (5 seconds), and mass-producible seed-mediated synthesis method to prepare branched Au superparticles consisting of multiple small Au island-like nanoparticles by a wet chemical route. We reveal and confirm the toggling formation mechanism of Au superparticles between the Frank-van der Merwe (FM) growth mode and the Volmer-Weber (VW) growth mode. The key factor of this special structure is the frequent toggling between the FM (layer by layer) growth mode and the VW (island) growth mode induced by 3-aminophenol, which is continuously absorbed on the surface of newborn Au nanoparticles, leading to a relatively high surface energy during the overall synthesis process, thus achieving an island on island growth. Such Au superparticles demonstrate broadband absorption from visible to near-infrared regions due to their multiple plasmonic coupling and hence they have important applications in sensors, photothermal conversion and therapy, etc. We also exhibit the excellent properties of Au superparticles with different morphologies, such as NIR-II photothermal conversion and therapy and SERS detection. The photothermal conversion efficiency under 1064 nm laser irradiation was calculated to be as high as 62.6% and they exhibit robust photothermal therapy efficiency. This work provides insight into the growth mechanism of plasmonic superparticles and develops a broadband absorption material for highly efficient optical applications.

Density functional theory computation of the intermolecular interactions of Al2@C24 and Al2@Mg12O12 semiconducting quantum dots conjugated with the glycine tripeptide

The nature of intermolecular forces within semiconductor quantum dot systems can determine various physicochemical properties, as well as their functions, in nanomedical applications. The purpose of this study has been to investigate the nature of the intermolecular forces operating between Al₂@C₂₄ and A_l2@Mg₁₂O₁₂ semiconducting quantum dots and the glycine tripeptide (GlyGlyGly), and also consider whether permanent electric dipole–dipole interactions play a significant role vis-à-vis these molecular systems. The energy computations, including the Keesom and the total electronic interactions and the energy decomposition, together with the quantum topology analyses were performed. Our results demonstrate that no significant correlation is found between the magnitude and orientation of the electrical dipole moments, and the interaction energy of the Al₂@C₂₄ and A_l2@Mg₁₂O₁₂ with GlyGlyGly tripeptide. The Pearson correlation coefficient test revealed a very weak correlation between the quantum and the Keesom interaction energies. Apart from the quantum topology analyses, the energy decomposition consideration confirmed that the dominant share of the interaction energies was associated with the electrostatic interactions, yet both the steric and the quantum effects also made appreciable contributions. We conclude that, beside the electrical dipole–dipole interactions, other prominent intermolecular forces, such as the polarization attraction, the hydrogen bond, and the van der Waals interactions can also influence the interaction energy of the system. The findings of this study can be utilized in several areas in the field of nanobiomedicine, including the rational design of cell-penetrating and intracellular drug delivery systems using semiconducting quantum dots functionalized with a peptide.

The nature of intermolecular forces within semiconducting quantum dot systems can determine various physicochemical properties, as well as their functions, in nanomedical applications.

Structural diversity in three-dimensional self-assembly of nanoplatelets by spherical confinement

Nanoplatelets offer many possibilities to construct advanced materials due to new properties associated with their (semi)two-dimensional shapes. However, precise control of both positional and orientational order of the nanoplatelets in three dimensions, which is required to achieve emerging and collective properties, is challenging to realize. Here, we combine experiments, advanced electron tomography and computer simulations to explore the structure of supraparticles self-assembled from nanoplatelets in slowly drying emulsion droplets. We demonstrate that the rich phase behaviour of nanoplatelets, and its sensitivity to subtle changes in shape and interaction potential can be used to guide the self-assembly into a wide range of different structures, offering precise control over both orientation and position order of the nanoplatelets. Our research is expected to shed light on the design of hierarchically structured metamaterials with distinct shape- and orientation- dependent properties.

Nanoplatelets can be used as anisotropic building blocks for constructing novel optoelectronic materials. Here, Wang et al. show a route of assembling nanoplatelets with controllable positional and orientational order in three dimensions facilitated by the surface tension of drying emulsion droplets.

From binary AB to ternary ABC supraparticles

Control over the assembly and morphology of nanoscale functional building blocks is of great importance to hybrid and porous nanomaterials. In this paper, by combining different types of spherical nanoparticles with different size ratios in a hierarchical assembly process which allows us to control the final structure of multi-component assemblies, we discuss self-assembly of an extensive range of supraparticles, labelled as AB particles, and an extension to novel ternary particles, labelled as ABC particles. For supraparticles, the organization of small nanoparticles is known to be inherently related to the size ratio of building blocks. Therefore, we studied the formation of supraparticles prepared by colloidal self-assembly using small silica nanoparticles (SiO₂ NPs) attached on the surface of large polystyrene latex nanoparticles (PSL NPs) with a wide size ratio range for complete and partial coverage, by controlling the electrostatic interactions between the organic and inorganic nanoparticles and their concentrations. In this way hierarchically ordered, stable supraparticles, either fully covered or partially covered, were realized. The partially covered, stable AB supraparticles offer the option to create ABC supraparticles of which the fully covered shell contains two different types of nanoparticles. This has been experimentally confirmed using iron oxide (Fe₃O₄) nanoparticles together with silica nanoparticles as shell particles on polystyrene core particles. Cryo-electron tomography was used to visualize the AB binary and ABC ternary supraparticles and to determine the three-dimensional structural characteristics of supraparticles formed under different conditions.

Self-Assembled Supercrystals Enhance the Photothermal Conversion for Solar Evaporation and Water Purification

Photothermal materials can convert renewable solar energy into thermal energy and have great potential for solar water evaporation. Copper sulfide (Cu_{2- x} S) is an easily available and inexpensive plasmonic material with a high photothermal conversion efficiency and can be applied to solar evaporation and water purification. Monodispersed Cu₇ S₄ nanoparticles (NPs) and supercrystalline self-assembled superparticles are obtained via wet chemical synthesis and micelle self-assembly. The photothermal properties of the superstructures are investigated using the finite difference time domain method and laser radiation photothermography. The results show that the electromagnetic field intensity and photothermal efficiency of the self-assembly are significantly higher than those of isolated NPs, which is due to the plasmonic coupling of the NPs. The evaporation efficiency of the superstructure is significantly higher than that of isolated NPs, the metal salt ion and total organic carbon concentrations in the waterbody significantly decrease after evaporation, and the water polluted by high salt and organic dye concentrations is purified. The water quality significantly improves after the lake water from Fuxian Lake in the Yunnan-Guizhou Plateau of China is used for solar evaporation. The color changes from pale yellow to colorless and the ion and total organic carbon contents significantly decrease.

Structural Reconstruction of Cu2 O Superparticles toward Electrocatalytic CO2 Reduction with High C2+ Products Selectivity

Structural reconstruction is a process commonly observed for Cu-based catalysts in electrochemical CO₂ reduction. The Cu-based precatalysts with structural complexity often undergo sophisticated structural reconstruction processes, which may offer opportunities for enhancing the electrosynthesis of multicarbon products (C₂₊ products) but remain largely uncertain due to various new structural features possibly arising during the processes. In this work, the Cu₂ O superparticles with an assembly structure are demonstrated to undergo complicated structure evolution under electrochemical reduction condition, enabling highly selective CO₂ -to-C₂₊ products conversion in electrocatalysis. As revealed by electron microscopic characterization together with in situ X-ray absorption spectroscopy and Raman spectroscopy, the building blocks inside the superparticle fuse to generate numerous grain boundaries while those in the outer shell detach to form nanogap structures that can efficiently confine OH^- to induce high local pH. Such a combination of unique structural features with local reaction environment offers two important factors for facilitating C-C coupling. Consequently, the Cu₂ O superparticle-derived catalyst achieves high faradaic efficiencies of 53.2% for C₂ H₄ and 74.2% for C₂₊ products, surpassing the performance of geometrically simpler Cu₂ O cube-derived catalyst and most reported Cu electrocatalysts under comparable conditions. This work provides insights for rationally designing highly selective CO₂ reduction electrocatalysts by controlling structural reconstruction.

Coloration in Supraparticles Assembled from Polyhedral Metal-Organic Framework Particles

Supraparticles are spherical colloidal crystals prepared by confined self‐assembly processes. A particularly appealing property of these microscale structures is the structural color arising from interference of light with their building blocks. Here, we assemble supraparticles with high structural order that exhibit coloration from uniform, polyhedral metal–organic framework (MOF) particles. We analyse the structural coloration as a function of the size of these anisotropic building blocks and their internal structure. We attribute the angle‐dependent coloration of the MOF supraparticles to the presence of ordered, onion‐like layers at the outermost regions. Surprisingly, even though different shapes of the MOF particles have different propensities to form these onion layers, all supraparticle dispersions show well‐visible macroscopic coloration, indicating that local ordering is sufficient to generate interference effects.

Self-Assembly of Upconversion Nanoparticles Based Materials and Their Emerging Applications

In the past few decades, significant progress of the conventional upconversion nanoparticles (UCNPs) based nanoplatform has been achieved in many fields, and with the development of nanoscience and nanotechnology, more and more complex situations need a UCNPs based nanoplatform having multifunctions for specific multimodal or multiplexed applications. Through self-assembly, different UCNPs or UCNPs with other materials could be combined together within an entity. It is more like an ideal UCNPs nanoplatform, a unique system with the properties defined by its individual components as well as by the morphology of the composite. Various designs can show their different desired properties depending on the application situation. This review provides a complete summary on the optimization of the synthesis method for the recently designed UCNPs assemblies and summarizes various applications, including dual-modality cell imaging, molecular delivery, detection, and programmed control therapy. The challenges and limitations the UCNPs assembly faces and the potential solutions in this field are also presented.

Self-assembled inorganic chiral superstructures

Controlled assembly of inorganic nanoparticles with different compositions, sizes and shapes into higher-order structures of collective functionalities is a central pursued objective in chemistry, physics, materials science and nanotechnology. The emerging chiral superstructures, which break spatial symmetries at the nanoscale, have attracted particular attention, owing to their unique chiroptical properties and potential applications in optics, catalysis, biology and so on. Various bottom-up strategies have been developed to build inorganic chiral superstructures based on the intrinsic configurational preference of the building blocks, external fields or chiral templates. Self-assembled inorganic chiral superstructures have demonstrated significant superior optical activity from the strong electric/magnetic coupling between the building blocks, as compared with the organic counterparts. In this Review, we discuss recent progress in preparing self-assembled inorganic chiral superstructures, with an emphasis on the driving forces that enable symmetry breaking during the assembly process. The chiroptical properties and applications are highlighted and a forward-looking trajectory of where research efforts should be focused is discussed.

Dynamic nanoassembly-based drug delivery systems on the horizon

Self-assembly in nature creates matter with complex structures and unpredictable designs; disordered building blocks spontaneously organize into ordered structures to achieve specific functions. Self-assembly begins to play an important role in the design of advanced drug delivery as well. Though, the behavior of 'dynamic nanoassembly-based drug delivery systems' (DNDDS) in biological media and cells remains poorly understood, while this is highly critical for controlling spatiotemporal drug release from DNDDS in vivo. To deepen the understanding of tailor-made DNDDS, this contribution in the Oration - New Horizons section of the Journal of controlled Release aims to highlight nature-inspired designs, construction principles, and controllable functionalities of DNDDS and how they are triggered by endogenous and exogenous stimuli. Furthermore, biomedical applications of tailor-made DNDDS for accurate diagnosis and precise treatment of diseases, including tumors, neurological diseases, injuries and infections are discussed. Finally, current challenges and future perspectives of DNDDS are briefly outlined.

3D Printing-Enabled Nanoparticle Alignment: A Review of Mechanisms and Applications

3D printing (additive manufacturing (AM)) has enormous potential for rapid tooling and mass production due to its design flexibility and significant reduction of the timeline from design to manufacturing. The current state-of-the-art in 3D printing focuses on material manufacturability and engineering applications. However, there still exists the bottleneck of low printing resolution and processing rates, especially when nanomaterials need tailorable orders at different scales. An interesting phenomenon is the preferential alignment of nanoparticles that enhance material properties. Therefore, this review emphasizes the landscape of nanoparticle alignment in the context of 3D printing. Herein, a brief overview of 3D printing is provided, followed by a comprehensive summary of the 3D printing-enabled nanoparticle alignment in well-established and in-house customized 3D printing mechanisms that can lead to selective deposition and preferential orientation of nanoparticles. Subsequently, it is listed that typical applications that utilized the properties of ordered nanoparticles (e.g., structural composites, heat conductors, chemo-resistive sensors, engineered surfaces, tissue scaffolds, and actuators based on structural and functional property improvement). This review's emphasis is on the particle alignment methodology and the performance of composites incorporating aligned nanoparticles. In the end, significant limitations of current 3D printing techniques are identified together with future perspectives.

Controlling supraparticle shape and structure by tuning colloidal interactions

HYPOTHESIS

Assembly of colloids in drying colloidal suspensions on superhydrophobic surface is influenced by the colloidal interactions, which determine the shape and interior structure of the assembled supraparticle. The introduction of salt (electrolyte) into the assembly system is expected to influence the colloid interactions and packing during the evaporation process. Hence, both the outer shape and internal structure of supraparticles should be controlled by varying salt concentrations.

EXPERIMENTS

Suspensions of electrostatically stabilized polystyrene particles with specified salt concentrations were chosen as model systems to conduct the evaporation on a superhydrophobic surface. A systematic study was performed by regulating the concentration and valency of salt. The morphology and interior of supraparticles were carefully characterized with electron scanning microscopy, while the colloidal interaction was established using colloidal probe atomic force microscopy.

FINDINGS

Supraparticles displayed a spherical-to-nonspherical shape change due to the addition of salts. The extent of crystallization depended on salt concentration. These changes in shape and structure were correlated with salt-dependent single colloid interaction forces, which were not previously investigated in detail in radially symmetric evaporation geometry. Our findings are crucial for understanding assembly behavior during the drying process and offer guidance for preparing complex supraparticles to meet specific applications requirement.

Mesocrystals from Platinum Nanocubes

Platinum nanoparticles are widely known for their numerous electrochemical and catalytic applications. Enhanced or novel properties that may arise when ordering such particles in a highly defined manner, however, are still subject to ongoing research, as superstructure formation on the mesoscale is still a major challenge to be overcome. In this work, we therefore established a reproducible method to fabricate micrometer-sized superstructures from platinum nanocubes. Through small-angle X-ray scattering and electron diffraction methods we demonstrate that the obtained superstructures have a high degree of ordering up to the atomic scale and, therefore, fulfill all criteria of a mesocrystal. By changing the solvent and stabilizer in which the platinum nanocubes were dispersed, we were able to control the resulting crystal habit of the mesocrystals. Aside from mesocrystal fabrication, this method can be further utilized to purify nanoparticle dispersions by recrystallization with respect to narrowing down the particle size distribution and removing contaminations.

Self-assembly of colloidal inorganic nanocrystals: nanoscale forces, emergent properties and applications

The self-assembly of colloidal nanoparticles has made it possible to bridge the nanoscopic and macroscopic worlds and to make complex nanostructures. The nanoparticle-mediated assembly enables many potential applications, from biodetection and nanomedicine to optoelectronic devices. Properties of assembled materials are determined not only by the nature of nanoparticle building blocks, but also by spatial positions of nanoparticles within the assemblies. A deep understanding of nanoscale interactions between nanoparticles is a prerequisite to controlling nanoparticle arrangement during assembly. In this review, we present an overview of interparticle interactions governing their assembly in a liquid phase. Considerable attention is devoted to examples that illustrate nanoparticle assembly into ordered superstructures using different types of building blocks, including plasmonic nanoparticles, magnetic nanoparticles, lanthanide-doped nanophosphors, and quantum dots. We also cover the physicochemical properties of nanoparticle ensembles, especially those arising from particle coupling effects. We further discuss future research directions and challenges in controlling self-assembly at a level of precision that is most crucial to technology development.

Self-limiting self-assembly of supraparticles for potential biological applications

Nanotechnology has largely spurred the development of biological systems by taking advantage of the unique chemical, physical, optical, magnetic, and electrical properties of nanostructures. Self-limiting self-assembly of supraparticles produce new nanostructures and display great potential to create biomimicking nanostructures with desired functionalities. In this minireview, we summarize the recent developments and outstanding achievements of colloidal supraparticles, such as the driving forces for self-limiting self-assembly of supraparticles and properties of constructed supraparticles. Their application values in biological systems have also been illustrated.

Highly Stable CsPbBr3 Colloidal Nanocrystal Clusters as Photocatalysts in Polar Solvents

One of the main challenges of all-inorganic cesium lead halide (CsPbX₃) perovskite nanocrystals (NCs) in photocatalysis is their poor stability in hostile environments such as polar solvents. Herein, we report highly stable CsPbBr₃ colloidal nanocrystal clusters (CNCs) with uniform morphology and size prepared by using a PVP-assisted reprecipitation method. A possible formation process through a self-assembly avenue is proposed. These CsPbBr₃ CNCs exhibit much enhanced resistance against a variety of polar solvents in comparison with CsPbBr₃ NCs obtained from the commonly used hot-injection method. In addition, this method can be generalized to the synthesis of lead-free perovskites CNCs. The as-prepared CsPbBr₃ CNCs display good reactivity and high durability in photocatalytic degradation of methylene blue in alcoholic systems. This work will shed some light on the stabilization of perovskite NCs in polar solvents and perovskite NC-based photocatalysts.

Facile fabrication of self-assembled nanostructures of vertically aligned gold nanorods by using inkjet printing

We demonstrated that the vertically aligned gold nanorods (AuNRs) were quickly and easily formed by using inkjet printing when aqueous dispersion of AuNRs containing a small amount of ethylene glycol (EG) was employed as an ink. It was observed that the content of EG in water suppressed rapid drying and convection in the droplets, which is favorable for the formation of the nanostructures.

Slow evaporation of a droplet of water/ethylene glycol (EG) mixture allows the fabrication of vertically aligned gold nanorods using inkjet printing.

Confined space design by nanoparticle self-assembly

Nanoparticle (NP) self-assembly has led to the fabrication of an array of functional nanoscale systems, having diverse architectures and functionalities. In this perspective, we discuss the design and application of NP suprastructures (SPs) characterized by nanoconfined compartments in their self-assembled framework, providing an overview about SP synthetic strategies reported to date and the role of their confined nanocavities in applications in several high-end fields. We also set to give our contribution towards the formation of more advanced nanocompartmentalized SPs able to work in dynamic manners, discussing the opportunities of further advances in NP self-assembly and SP research.

Noble Metal Aerogels

Noble metal-based nanomaterials have been a hot research topic during the past few decades. Particularly, self-assembled porous architectures have triggered tremendous interest. At the forefront of porous nanostructures, there exists a research endeavor of noble metal aerogels (NMAs), which are unique in terms of macroscopic assembly systems and three-dimensional (3D) porous network nanostructures. Combining excellent features of noble metals and the unique structural traits of porous nanostructures, NMAs are of high interest in diverse fields, such as catalysis, sensors, and self-propulsion devices. Regardless of these achievements, it is still challenging to rationally design well-tailored NMAs in terms of ligament sizes, morphologies, and compositions and profoundly investigate the underlying gelation mechanisms. Herein, an elaborate overview of the recent progress on NMAs is given. First, a simple description of typical synthetic methods and some advanced design engineering are provided, and then, the gelation mechanism models of NMAs are discussed in detail. Furthermore, promising applications particularly focusing on electrocatalysis and biosensors are highlighted. In the final section, brief conclusions and an outlook on the existing challenges and future chances of NMAs are also proposed.

π-π stacking-directed self-assembly of nanoplatelets into diversified three-dimensional superparticles for high surface-enhanced Raman scattering

Ordered, hierarchical structures formed from nanoparticle (NP) self-assembly are of interest as they display the synergistic properties of the individual NP. Herein we report a one-pot approach to form and self-assemble gold (Au) nanoplatelets into brick-wall like (BWL) Au superparticles (AuSPs). We employ an aniline (ANI) derivative, N-(3-amidino)-aniline (NAAN) to reduce the Au precursor into Au nanoplatelets in the presence of Br^-1. The corresponding oxidation product, poly (N-(3-amidino)-aniline) (PNAAN) functions as the capping agent and enables the face-to-face self-assembly of Au nanoplatelets into BWL AuSPs via the π-π stacking interaction. Systematically tuning the reaction conditions leads to spherical, mushroom- or cauliflower-like AuSPs. The significant electromagnetic enhancement of AuSPs via the formation of the nanogaps produces high-density hotspots for excellent surface-enhanced Raman scattering (SERS) enhancement, enabling the ultrasensitive SERS assay with detection limit of pM. Moreover, the as-prepared AuSPs exhibited the intense SERS signals under laser excitation with different wavelength and the excellent reproducibility after long-duration exposure in different media. The developed SERS sensor has a great potential for a wide application of bioanalysis, clinic assays and environmental monitoring.

Crystallization in Confinement

Many crystallization processes of great importance, including frost heave, biomineralization, the synthesis of nanomaterials, and scale formation, occur in small volumes rather than bulk solution. Here, the influence of confinement on crystallization processes is described, drawing together information from fields as diverse as bioinspired mineralization, templating, pharmaceuticals, colloidal crystallization, and geochemistry. Experiments are principally conducted within confining systems that offer well-defined environments, varying from droplets in microfluidic devices, to cylindrical pores in filtration membranes, to nanoporous glasses and carbon nanotubes. Dramatic effects are observed, including a stabilization of metastable polymorphs, a depression of freezing points, and the formation of crystals with preferred orientations, modified morphologies, and even structures not seen in bulk. Confinement is also shown to influence crystallization processes over length scales ranging from the atomic to hundreds of micrometers, and to originate from a wide range of mechanisms. The development of an enhanced understanding of the influence of confinement on crystal nucleation and growth will not only provide superior insight into crystallization processes in many real-world environments, but will also enable this phenomenon to be used to control crystallization in applications including nanomaterial synthesis, heavy metal remediation, and the prevention of weathering.

Self-assembly of anisotropic nanoparticles into functional superstructures

Self-assembly of colloidal nanoparticles (NPs) into superstructures offers a flexible and promising pathway to manipulate the nanometer-sized particles and thus make full use of their unique properties. This bottom-up strategy builds a bridge between the NP regime and a new class of transformative materials across multiple length scales for technological applications. In this field, anisotropic NPs with size- and shape-dependent physical properties as self-assembly building blocks have long fascinated scientists. Self-assembly of anisotropic NPs not only opens up exciting opportunities to engineer a variety of intriguing and complex superlattice architectures, but also provides access to discover emergent collective properties that stem from their ordered arrangement. Thus, this has stimulated enormous research interests in both fundamental science and technological applications. This present review comprehensively summarizes the latest advances in this area, and highlights their rich packing behaviors from the viewpoint of NP shape. We provide the basics of the experimental techniques to produce NP superstructures and structural characterization tools, and detail the delicate assembled structures. Then the current understanding of the assembly dynamics is discussed with the assistance of in situ studies, followed by emergent collective properties from these NP assemblies. Finally, we end this article with the remaining challenges and outlook, hoping to encourage further research in this field.

Direct conjugation of distinct carbon dots as Lego-like building blocks for the assembly of versatile drug nanocarriers

As a promising drug nanocarrier, carbon dots (CDs) have exhibited many excellent properties. However, some properties such as bone targeting and crossing the blood-brain barrier (BBB) only apply to a certain CD preparation with limited drug loading capacity. Therefore, it is significant to conjugate distinct CDs to centralize many unique properties on the novel drug nanocarrier. Considering that CDs have abundant and tunable surface functionalities, in this study, a direct conjugation was initiated between two distinct CD models, black CDs (B-CDs) and gel-like CDs (G-CDs) via an amidation reaction. As a result of conjugation at a mass ratio of 5:3 (B-CDs to G-CDs) and a two-step purification process, the conjugate, black-gel CDs (B-G CDs) (5:3) inherited functionalities from both CDs and obtained an enhanced thermostability, aqueous stability, red-shifted photoluminescence (PL) emission, and a figure-eight shape with a width and length of 3 and 6 nm, respectively. In addition, the necessity of high surface primary amine (NH₂) content in the CD conjugation was highlighted by replacing G-CDs with other CDs with lower surface NH₂ content. Meanwhile, the carboxyl groups (COOH) on G-CDs were not enough to trigger self-conjugation between G-CDs. Moreover, the drug loading capacity was enhanced by 54.5% from B-CDs to B-G CDs (5:3). Furthermore, when the mass ratio of B-CDs to G-CDs was decreased from 5:30, 5:100 to 5:300, the obtained nanostructures revealed a great potential of CDs as Lego-like building blocks. Also, bioimaging of zebrafish demonstrated that various B-G CDs exhibited properties of both bone targeting and crossing the BBB, which are specific properties of B-CDs and G-CDs, respectively.

Effect of structure: A new insight into nanoparticle assemblies from inanimate to animate

Nanoparticle (NP) assemblies are among the foremost achievements of nanoscience and nanotechnology because their interparticle interactions overcome the weaknesses displayed by individual NPs. However, previous studies have considered NP assemblies as inanimate, which had led to their dynamic properties being overlooked. Animate properties, i.e., those mimicking biological properties, endow NP ensembles with unique and unexpected functionalities for practical applications. In this critical review, we highlight recent advances in our understanding of the properties of NP assemblies, particularly their animate properties. Key examples are used to illustrate critical concepts, and special emphasis is placed on animate property-dependent applications. Last, we discuss the barriers to further advances in this field.

Melanin-based nanomaterials: The promising nanoplatforms for cancer diagnosis and therapy

Melanin-based nanoplatforms are biocompatible nanomaterials with a variety of unique physicochemical properties such as strong photothermal conversion ability, excellent drug binding capacity, strong metal chelation capacity, high chemical reactivity and versatile adhesion ability. These innate talents not only make melanin-based nanoplatforms be an inborn theranostic nanoagent for photoacoustic imaging-guided photothermal therapy of cancers, but also enable them to be conveniently transferred into cancer-targeting drug delivery systems and multimodality imaging nanoprobes. Due to the intriguing properties, melanin-based nanoplatforms have attracted much attention in investigations of cancer diagnosis and therapy. This review provides an overview of recent research advances in applications of melanin-based nanoplatforms in the fields of cancer diagnosis and therapy including cancer photothermal therapy, anticancer drug delivery, cancer-specific multimodal imaging and theranostics, etc. The remaining challenges and prospects of melanin-based nanoplatforms in biomedical applications are discussed at the end of this review.

Self-assembled colloidal gold superparticles to enhance the sensitivity of lateral flow immunoassays with sandwich format

Background: Traditional lateral flow immunoassay (LFIA) based on 20-40 nm gold nanoparticles (AuNPs) as signal reporter always suffers from relatively low detection sensitivity due to its insufficient brightness, severely restricting its wide-ranging application in the detection of target analytes with trace concentration.

Methods: To address this problem, the self-assembled colloidal gold superparticles (GSPs) were synthesized as an improved absorption-dominated labeling probe for improving the sensitivity of sandwich LFIA. Five kinds of GSPs with the size ranging from 100 nm to 400 nm were synthesized by embedding hydrophobic AuNPs of size 12 nm as building blocks into the polymer nanobeads. The as-prepared GSPs were suggested as novel labeling probes of LFIA. The effects of the size of assembled GSPs on the sensitivity of sandwich LFIA was assessed, and the detection performance of GSPs-LFIA was further compared with traditional AuNPs-LFIA.

Results: The resultant GSPs showed extremely high light absorption but very low light scattering, which favor the absorption-dominated signal output in LFIA. Among them, the GSP₂₇₀-LFIA (size 270 nm) exhibits the highest sensitivity for human chorionic gonadotropin and hepatitis B surface antigen detection in real serum sample, which are approximate 39.79- and 13.8-fold higher than that of traditional AuNP₄₀-LFIA.

Conclusions: The proposed research demonstrated that the current GSPs can provide an ultrasensitive and quantitative detection for disease biomarkers in real serum samples as promising reporters of sandwich LFIA platform.

Structural changes in colloid solutions of nanodiamond

Segregation of particles in a nanodiamond aqueous colloid due to Stokes’ law leads to re-ordering of the lattice of particles.

Linker-assisted structuration of tunable uranium-based hybrid lamellar nanomaterials

Linker-assisted formation of tunable uranium-based hybrid lamellar nano-sheets through a non-hydrolytic condensation process.

Dynamic supraparticles for the treatment of age-related diseases

Age-related diseases (ARDs) are arising as a major threat to public health in our fast-aging society. Current development of nanomedicine has sparked much optimism toward ARDs management by improving drug delivery and controlled drug release. However, effective treatments for ARDs, such as cancer and Alzheimer's diseases (AD), are still lacking, due to the complicated pathological features of ARDs including multifactorial pathogenesis, intricate disease microenvironment, and dynamic symptom manifestation. Recently, dynamic supraparticles (DS), which are reversibly self-assembled functional nanoparticles, have provided a novel strategy for combating ARDs. Besides the intrinsic advantages of nanomedicine including multifunctional and multitarget, DS are capable of dynamic structural reconfiguration upon certain stimulation, creating another layer of maneuverability that allows programmed response to the spatiotemporal alterations of ARDs during progression and treatment. In this review, we will overview the challenges faced by ARDs management, and discuss the unique opportunities brought by DS. Then, we will summarize the designed synthesis of DS for ARDs treatment. Finally, we will dissect the therapeutic targets in ARDs that can be exploited by DS, and present the encouraging advances in this field. Hopefully, this review will bridge our knowledge of the design principle of DS and ARDs management, which may inspire the future development of potent theranostic agents to improve the healthcare.

Tuning the Porosity of Supraparticles

Supraparticles consisting of nano- or microparticles have potential applications as, for example, photonic crystals, drug carriers, or heterogeneous catalysts. To avoid the use of solvent or processing liquid, one can make supraparticles by evaporating droplets of aqueous suspensions from super-liquid-repellent surfaces. Herein, a method to adjust the porosity of supraparticles is described; a high porosity is desired, for example, in catalysis. To prepare highly porous TiO₂ supraparticles, polymer nanoparticles are co-dispersed in the suspension. Supraparticles are formed through evaporation of aqueous suspension droplets on superamphiphobic surfaces followed by calcination of the sacrificial polymer particles. The increase of porosity of up to 92% resulted in enhanced photocatalytic activity while maintaining sufficient mechanical stability.

Seeded-Growth of Silica Rods from Silica-Coated Particles

Seeded growth of silica rods from colloidal particles has emerged as a facile method to develop novel complex particle structures with hybrid compositions and asymmetrical shapes. However, this seeded-growth technique has been so far limited to colloidal particles of only a few materials. Here, we first develop a general synthesis for the seeded-growth of silica rods from silica particles. We then demonstrate the growth of silica rods from silica-coated particles with three different cores which highlight the generality of this synthesis: fluorescently labeled organo-silica (fluorescein), metallic (Ag), and organic (PS latex). We also demonstrate the assembly of these particles into supraparticles. This general synthesis method can be extended to the growth of silica rods from any colloidal particle which can be coated with silica.

Oxygen-catalysed sequential singlet fission

Singlet fission is the photoinduced conversion of a singlet exciton into two triplet states of half-energy. This multiplication mechanism has been successfully applied to improve the efficiency of single-junction solar cells in the visible spectral range. Here we show that singlet fission may also occur via a sequential mechanism, where the two triplet states are generated consecutively by exploiting oxygen as a catalyst. This sequential formation of carriers is demonstrated for two acene-like molecules in solution. First, energy transfer from the excited acene to triplet oxygen yields one triplet acene and singlet oxygen. In the second stage, singlet oxygen combines with a ground-state acene to complete singlet fission. This yields a second triplet molecule. The sequential mechanism accounts for approximately 40% of the triplet quantum yield in the studied molecules; this process occurs in dilute solutions and under atmospheric conditions, where the single-step SF mechanism is inactive.

Halogen bond-assisted self-assembly of gold nanoparticles in solution and on a planar surface

Halogen bonding (XB) has been shown to be a powerful tool for promoting molecular self-assembly in different fields. The use of XB for noncovalent assembly of inorganic nanoparticles (NP) is, instead, quite limited, considering how extensively other interactions (i.e., electrostatic forces, hydrophobic effect, hydrogen bonding, etc.) have been exploited to modulate and program NP self-assembly. Here, we designed and synthesized XB-capable organic ligands that were efficiently used to functionalize the surface of gold NPs (AuNPs). XB-assisted AuNP self-assembly was attained in solution mixing AuNPs bearing XB-donor ligands with ditopic XB-acceptor molecules and AuNPs functionalized with XB-acceptor moieties. Likewise, a preliminary study of XB-driven adsorption of these AuNPs on surface was performed via Quartz Crystal Microbalance with Dissipation Monitoring (QCM-D), used as an in situ tool for measuring mass changes upon XB-driven self-assembly.

Directed Nanoparticle Assembly through Polymer Crystallization

Nanoparticles can be assembled into complex structures and architectures by using a variety of methods. In this review, we discuss recent progress of using polymer crystallization (particularly polymer single crystals, PSCs) to direct nanoparticle assembly. PSCs have been extensively studied since 1957. Mainly appearing as quasi-two-dimensional (2D) lamellae, PSCs are typically used as model systems to determine polymer crystalline structures, or as markers to investigate the crystallization process. Recent research has demonstrated that they can also be used as nanoscale functional materials. Herein, we show that nanoparticles can be directed to assemble into complex shapes by using in situ or ex situ polymer crystal growth. End-functionalized polymers can crystallize into 2D nanosheet PSCs, which are used to conjugate with complementary nanoparticles, leading to a nanosandwich structure. These nanosandwiches can find interesting applications for catalysis, surface-enhanced Raman spectroscopy, and nanomotors. Dissolution of the nanosandwich leads to the formation of Janus nanoparticles, providing a unique method for asymmetric nanoparticle synthesis.

Simple Preparation of Hierarchically Porous Ce/TiO2/Graphitic Carbon Microspheres for the Reduction of CO2 with H2O under Simulated Solar Irradiation

Hierarchically porous Ce/TiO2/graphitic carbon microsphere composites (xCe/TiO2/GCM, where x = 0.2, 1.0, 2.0, 5.0 mmol·L-1) were prepared for the first time by using a simple colloidal crystal template and characterized by X-ray diffraction, nitrogen adsorption and desorption, scanning electron microscopy, and ultraviolet-visible diffuse reflectance spectra. In addition, the photocatalytic activity of CO2 reduction by H2O under simulated solar irradiation was studied. The results showed that the Ce/TiO2/GCM composite material was characterized by large porosity, high concentration of metal compounds and graphitized carbon matrix, and the content of acetone solvent having a great impact on its form. In terms of the photocatalytic CO2 reaction, the CH4 and CO productions were 4.587 and 357.851 μmol·g-1, respectively. The 2Ce/TiO2/GCM photocatalyst gave the highest production rate for three products. Under simulated solar irradiation, the Ce/TiO2/GCM has excellent photocatalytic activity in the photoreduction of CO2 from H2O, which was related to the special composition and the Ce/TiO2/GCM structure.