Green Phytic Acid-Assisted Synthesis of LiMn1-xFexPO4/C Cathodes for High-Performance Lithium-Ion Batteries

As a promising cathode material, olivine-structured LiMnPO4 holds enormous potential for lithium-ion batteries. Herein, we demonstrate a green biomass-derived phytic-acid-assisted method to synthesize a series of LiMn1-xFexPO4/C composites. The effect of Fe doping on the crystal structure and morphology of LiMnPO4 particles is investigated. It is revealed that the optimal Fe doping amount of x = 0.2 enables a substantial enhancement of interfacial charge transfer ability and Li+ ion diffusion kinetics. Consequently, a large reversible capacity output of 146 mAh g-1 at 0.05 C and a high rate capacity of 77 mAh g-1 at 2 C were acquired by the as-optimized LiMn0.8Fe0.2PO4/C cathode. Moreover, the LiMn0.8Fe0.2PO4/C delivered a specific capacity of 68 mAh g-1 at 2 C after 500 cycles, with a capacity retention of 88.4%. This work will unveil a green synthesis route for advancing phosphate cathode materials toward practical implementation.

Preparation and Evaluation of Co-Doped Fe7S8/C Composites for Lithium Storage

Fe₇S₈ has a high theoretical capacity (663 mAh g^-1) and can be prepared at a low cost, making it advantageous for production. However, Fe₇S₈ has two disadvantages as a lithium-ion battery anode material. The first is that the conductivity of Fe₇S₈ is not good. The second is that when the lithium ion is embedded, the volume expansion of the Fe₇S₈ electrode is serious. That is why Fe₇S₈ has not been used in real life yet. In this paper, Co-Fe₇S₈/C composites were prepared by doping Co into Fe₇S₈ through a one-pot simple hydrothermal method. In situ Co is doped into Fe₇S₈ to produce a more disordered microstructure to improve ion and electron transport performance, thereby reducing the activation barrier of the main material. The Co-Fe₇S₈/C electrode presents a high specific discharge capacity of 1586 mAh g^-1 and a Coulombic efficiency (CE) of 71.34% at an initial cycle at 0.1 A g^-1. After 1500 cycles, the specific discharge capacity remains at 436 mAh g^-1 (5 A g^-1). When the current density returns to 0.1 A g^-1, the capacity almost returns to the initial level, showing excellent rate performance.

Self-templating hydrothermal synthesis of carbon-confined double-shelled Ni/NiO hollow microspheres for diphenylamine detection in fruit samples

Toxic substances, such as heavy metals, toxins, pesticides, pathogens, and veterinary drug residues in food are hazardous to consumer health. The variety and quantity of food consumption have increased owing to developments in the agricultural and food industries. Food safety has a substantial socioeconomic impact, and an increasing number of consumers have become aware of its importance. Therefore, simple and cost-effective analytical methods are required to quantify the safety of preservatives. Herein, we report an electrochemical method using double-shelled carbon-confined Ni/NiO (C@Ni/NiO) hollow microspheres to detect diphenylamine (DPA). The microspheres were synthesized by a self-templating hydrothermal method followed by calcination. The hydrothermal temperature and precursor ratio were optimized systematically to prepare double-shelled C@Ni/NiO hollow microspheres. The excellent electrocatalytic activity and electron transport properties of a C@Ni/NiO-modified glassy carbon electrode (GCE) were exploited in the electrochemical oxidation of DPA. Interestingly, the engineered C@Ni/NiO/GCE has a wide dynamic linear range (0.02-473 μM) and a DPA detection limit of 0.007 μM. In addition, the DPA sensor exhibited good selectivity, reproducibility, repeatability, and stability. The practical feasibility of the DPA sensor was evaluated in fruit samples (sweet tomatoes, apples, and red grapes), with considerable recovery.

A biological nanofoam: The wall of coniferous bisaccate pollen

The outer layer of the pollen grain, the exine, plays a key role in the survival of terrestrial plant life. However, the exine structure in different groups of plants remains enigmatic. Here, modern and fossil coniferous bisaccate pollen were examined to investigate the detailed three-dimensional structure and properties of the pollen wall. X-ray nanotomography and volume electron microscopy are used to provide high-resolution imagery, revealing a solid nanofoam structure. Atomic force microscopy measurements were used to compare the pollen wall with other natural and synthetic foams and to demonstrate that the mechanical properties of the wall in this type of pollen are retained for millions of years in fossil specimens. The microscopic structure of this robust biological material has potential applications in materials sciences and also contributes to our understanding of the evolutionary success of conifers and other plants over geological time.

Bio-Templating: An Emerging Synthetic Technique for Catalysts. A Review

In the last few years, researchers have focused their attention on the synthesis of new catalyst structures based on or inspired by nature. Biotemplating involves the transfer of biological structures to inorganic materials through artificial mineralization processes. This approach offers the main advantage of allowing morphological control of the product, as a template with the desired morphology can be pre-determined, as long as it is found in nature. This way, natural evolution through millions of years can provide us with new synthetic pathways to develop some novel functional materials with advantageous properties, such as sophistication, miniaturization, hybridization, hierarchical organization, resistance, and adaptability to the required need. The field of application of these materials is very wide, covering nanomedicine, energy capture and storage, sensors, biocompatible materials, adsorbents, and catalysis. In the latter case, bio-inspired materials can be applied as catalysts requiring different types of active sites (i.e., redox, acidic, basic sites, or a combination of them) to a wide range of processes, including conventional thermal catalysis, photocatalysis, or electrocatalysis, among others. This review aims to cover current experimental studies in the field of biotemplating materials synthesis and their characterization, focusing on their application in heterogeneous catalysis.

Sustainable Carbon Materials toward Emerging Applications

It is desirable for a sustainable society that the production and utilization of renewable materials are net-zero in terms of carbon emissions. Carbon materials with emerging applications in CO₂ utilization, renewable energy storage and conversion, and biomedicine have attracted much attention both academically and industrially. However, the preparation process of some new carbon materials suffers from energy consumption and environmental pollution issues. Therefore, the development of low-cost, scalable, industrially and economically attractive, sustainable carbon material preparation methods are required. In this regard, the use of biomass and its derivatives as a precursor of carbon materials is a major feature of sustainability. Recent advances in the synthetic strategy of sustainable carbon materials and their emerging applications are summarized in this short review. Emphasis is made on the discussion of the original intentions and various sustainable strategies for producing sustainable carbon materials. This review provides basic insights and significant guidelines for the further design of sustainable carbon materials and their emerging applications in catalysis and the biomedical field.

Nickel-Iron Nitride-Nickel Sulfide Composites for Oxygen Evolution Electrocatalysis

Advance applications like water splitting system and rechargeable metal-air battery are highly dependent on efficient electrocatalyst for the oxygen evolution reaction (OER). Heterostructured materials, with a high active surface area and electron effect, accomplish enhanced catalytic performance. Here, a nitride-sulfide composite (FeNi₃N-Ni₃S₂) has been prepared by a simple hydrothermal process coupled with nitridation. The prepared composite electrocatalyst FeNi₃N-Ni₃S₂ possesses lower electron densities compared to those of FeNi₃N and Ni₃S₂, lessening the activation energy (E_a) toward the OER. Consequently, the prepared FeNi₃N-Ni₃S₂ exhibits excellent OER performance with a low overpotential (230 mV) and a small Tafel slope (38 mV dec^-1). Highly stable FeNi₃N-Ni₃S₂ composite delivers lower charging voltage and extended lifetime in rechargeable Zn-air battery, compared with IrO₂.

3D hierarchical self-supported NiO/Co3O4@C/CoS2 nanocomposites as electrode materials for high-performance supercapacitors

Multi-dimensional nanomaterials have drawn great interest for application in supercapacitors due to their large accessible surface area. However, the achievements of superior rate capability and cycle stability are hindered by their intrinsic poor electronic/ionic conductivity and the erratic structure. Herein, we develop a three-dimensional hierarchical self-supported NiO/Co₃O₄@C/CoS₂ hybrid electrode, in which NiO/Co₃O₄ nanosheets are in situ grown on a nickel foam substrate and combined with CoS₂ nanospheres through a carbon medium. The hybrid electrode has a high specific capacity of ∼1025 C g^-1 at 1 A g^-1 with a superior rate performance of ∼74% capacity retention even at a current density of 30 A g^-1. Moreover, the assembled NiO/Co₃O₄@C/CoS₂//AC hybrid supercapacitor achieves excellent performance with a maximum voltage of 1.64 V and a high energy density of 62.83 W h kg^-1 at a power density of 824.99 W kg^-1 and excellent cycle stability performance with a capacity retention of ∼92% after 5000 cycles. The high electrochemical performance of the hybrid supercapacitor is mainly attributed to the porous structure of the NiO/Co₃O₄@C nanosheets and CoS₂ nanospheres and intimate integration of active species. The rational strategy for the combination of various earth-abundant nanomaterials paves a new way for energy storage materials.

Plasma modified BiOCl/sulfonated graphene microspheres as efficient photo-compensated electrocatalysts for the oxygen evolution reaction

Plasma regulation of oxygen vacancies in BiOCl/sulfonated graphene composites enables light energy compensation for the electrocatalytic OER process.

MOF-Derived CuS@Cu-BTC Composites as High-Performance Anodes for Lithium-Ion Batteries

The CuS(x wt%)@Cu-BTC (BTC = 1,3,5-benzenetricarboxylate; x = 3, 10, 33, 58, 70, 99.9) materials are synthesized by a facile sulfidation reaction. The composites are composed of octahedral Cu₃ (BTC)₂ ·(H₂ O)₃ (Cu-BTC) with a large specific surface area and CuS with a high conductivity. The as-prepared CuS@Cu-BTC products are first applied as the anodes of lithium-ion batteries (LIBs). The synergistic effect between Cu-BTC and CuS components can not only accommodate the volume change and stress relaxation of electrodes but also facilitate the fast transport of Li ions. Thus, it can greatly suppress the transformation process from Li₂ S to polysulfides by improving the reversibility of the conversion reaction. Benefiting from the unique structural features, the optimal CuS(70 wt%)@Cu-BTC sample exhibits a remarkably improved electrochemical performance, showing an over-theoretical capacity up to 1609 mAh g^-1 after 200 cycles (100 mA g^-1 ) with an excellent rate-capability of ≈490 mAh g^-1 at 1000 mA g^-1 . The outstanding LIB properties indicate that the CuS(70 wt%)@Cu-BTC sample is a highly desirable electrode material candidate for high-performance LIBs.

Synthesis of Diverse Green Carbon Nanomaterials through Fully Utilizing Biomass Carbon Source Assisted by KOH

With multiple properties, green carbon nanomaterials with high specific surface area have become extensively attractive as energy storage devices with environmental-friendly features. The primary synthesis attempts were based on alkalis activation, which, however, faced the dilemma of low utilization rate of carbon sources. Herein, the green carbon with ultrahigh surface area (up to 3560 m²/g) was prepared by the KOH-assisted biomass carbonization. Moreover, the redundant K₂O steam and C_xH_y flow were further utilized; as a result, the carbon materials with a wide range of morphological diversity were collected on the Cu foam. Accordingly, we carried out density functional theory simulations to reveal the mechanism of O-adatom-promoted CH₄ dissociation over the Cu surface for carbon formation. The electrodes of electrochemical capacitor fabricated by carbon synthesis possess a 170% higher specific capacitance compared with commercial carbon electrodes. As such, this strategy might be promising in developing hierarchical carbons along with sufficient carbon sources for broadening their potential applications.

Importing Tin Nanoparticles into Biomass-Derived Silicon Oxycarbides with High-Rate Cycling Capability Based on Supercritical Fluid Technology

Silicon oxycarbides (SiOC) are regarded as potential anode materials for lithium-ion batteries, although inferior cycling stability and rate performance greatly limit their practical applications. Herein, amorphous SiOC is synthesized from Chlorella by means of a biotemplate method based on supercritical fluid technology. On this basis, tin particles with sizes of several nanometers are introduced into the SiOC matrix through the biosorption feature of Chlorella. As lithium-ion battery anodes, SiOC and Sn@SiOC can deliver reversible capacities of 440 and 502 mAh g^-1 after 300 cycles at 100 mA g^-1 with great cycling stability. Furthermore, as-synthesized Sn@SiOC presents an excellent high-rate cycling capability, which exhibits a reversible capacity of 209 mAh g^-1 after 800 cycles at 5000 mA g^-1 ; this is 1.6 times higher than that of SiOC. Such a novel approach has significance for the preparation of high-performance SiOC-based anodes.

Carboxyl functionalized carbon incorporation of stacked ultrathin NiO nanosheets: topological construction and superior lithium storage

Two-dimensional (2D) nanostructure engineering and surface modification with functional groups are of great importance to anode materials for rechargeable lithium-ion batteries. Herein, stacked NiO nanosheets@carbon (denoted as NiO@C) and 3 nm-ultrathin NiO nanosheets@functionalized carbon with surface functional groups NO3-, CO32-, OH-, and COOH- (denoted as NiO@FC) were prepared via a facile one-pot reaction and topotactic conversion. Specifically, NiO@FC exhibits excellent lithium storage performance: the capacity of NiO@FC is 489.2 mA h g-1, higher than that of NiO@C (1018.7 mA h g-1 at 0.2 A g-1), and maintains a capacity of 1133 mA h g-1 after 800 cycles, which exceed that of all previously reported NiO anodes. The enhanced lithium storage performance is attributed to the sufficient void space, which offers buffer space for volume change and speeds up the diffusion of Li+ ions. In addition, the surface functional groups were proved to not only hinder the agglomeration of nanosheets but also further donate active sites and improve storage capacity. These advantageous features achieved by designing such a stacked structure with functionalized carbon modification provide a promising strategy for the preparation of high-performance anode materials and other 2D functional materials.

Konjac glucomannan-templated synthesis of three-dimensional NiO nanostructures assembled from porous NiO nanoplates for gas sensors

Biopolymer template synthesis has attracted extensive interest for fabricating highly porous metal oxide nanostructures. In this report, a green template-based approach for the synthesis of three-dimensional (3D) NiO nanostructures assembled from porous NiO nanoplates is introduced using a konjac glucomannan (KGM) template. The Ni–KGM composites, which were formed by the immersion of KGM nanofibrils in nickel nitrate solution, were annealed in air at 600 °C to obtain the highly porous NiO nanoplates. The KGM nanofibrils were used as a sacrificial template, which was combusted at a high temperature for the formation of the porous nanostructures. The gas sensor properties of the porous NiO architecture were systematically investigated with four reduced gases including hydrogen sulfide, ammonia, carbon monoxide and hydrogen. The results indicate that the porous NiO nanoplates show a good detection of hydrogen sulfide with a rapid response and recovery speed at low concentrations.

Biopolymer template synthesis has attracted extensive interest for fabricating highly porous metal oxide nanostructures.

Three-Dimensional Biocarbon Framework Coupled with Uniformly Distributed FeSe Nanoparticles Derived from Pollen as Bifunctional Electrocatalysts for Oxygen Electrode Reactions

The development of carbon-based catalysts with satisfactory performance for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) is critical but challenging to achieve sustainable energy conversion and storage. Herein, a pollen biomass-derived carbon electrocatalyst with a three-dimensional porous framework, coupled with uniform distribution of FeSe nanoparticles, has been prepared by pyrolysis of the pollen precursor, followed by selenylation. The optimal catalyst FeSe/NC-PoFeSe exhibits a superb ORR activity with a half-wave potential of 0.86 V versus a reversible hydrogen electrode and OER activity with a low overpotential (330 mV at 10 mA cm^-2) in alkaline media, compared with commercial Pt/C and IrO₂/C catalysts, respectively. On the basis of the characterization results, we ascribe the enhanced ORR performance to sufficient Fe-N _x, pyridinic N, and graphitic N and the excellent OER performance in the presence of FeSe nanoparticles uniformly mounted on the N-doped carbon materials. In addition, we believe that the coupling effect between the FeSe nanoparticles and biocarbon led to a further improvement in the electrochemical performance. Significantly, the prominent ORR and OER stability of FeSe/NC-PoFeSe shows great promise in renewable energy devices.

Edge-Rich Quasi-Mesoporous Nitrogen-Doped Carbon Framework Derived from Palm Tree Bark Hair for Electrochemical Applications

Biomass with abundant resources and low price is regarded as potential sources of functionalized carbon-based energy storage and conversion electrode materials. Rational construction and development of biomass-derived carbon equipped with proper morphology, structure, and composition prove the key to highly efficient utilization of advanced energy storage systems. Herein, we use palm tree bark hair as a biomass source and prepare edge/defect-rich quasi-mesoporous carbon (QMC) by a direct pyrolysis followed by NaOH etching strategy. Then, the edge-rich quasi-mesoporous nitrogen-doped carbon (QMNC) is successfully fabricated through the hydrothermal method by making use of edge/defect-rich QMC and urea as carbon precursor and nitrogen source, respectively. The microstructure and composition of the resultant carbon materials are all detected by a series of techniques. In the meantime, the influence of the etching process on the preparation and electrochemical performance of edge-rich QMNC is systematically explored. The relevant results manifest that the as-prepared edge/defect-rich QMC not only possesses edge-rich plane, much increased specific surface area (SSA), and special quasi-mesopores but also reverses good conductivity and gains sufficient defects for subsequent N doping. After introducing N atoms, the obtained edge-rich QMNC exhibits outstanding capacitive property and oxygen reduction reaction performance, which are mainly attributed to the co-effect of edge-rich plane, large SSA, suitable pore structures, and effective N doping (including high doping amount and optimized N configurations). Clearly, our work not only offers an excellent biomass-derived carbon-based electrode material but also opens a fresh avenue for the development of advanced biomass-derived carbon-based electrode materials.

Wood Nanotechnology for Strong, Mesoporous, and Hydrophobic Biocomposites for Selective Separation of Oil/Water Mixtures

Tremendous efforts have been dedicated to developing effective and eco-friendly approaches for separation of oil-water mixtures. Challenges remain in terms of complex processing, high material cost, low efficiency, and scale-up problems. Inspired by the tubular porosity and hierarchical organization of wood, a strong, mesoporous, and hydrophobic three-dimensional wood structure is created for selective oil/water separation. A delignified wood template with hydrophilic characteristics is obtained by removal of lignin. The delignified wood template is further functionalized by a reactive epoxy-amine system. This wood/epoxy biocomposite reveals hydrophobic/oleophilic functionality and shows oil absorption as high as 15 g/g. The wood/epoxy biocomposite has a compression yield strength and modulus up to 18 and 263 MPa, respectively, at a solid volume fraction of only 12%. This is more than 20 times that of cellulose-based foams/aerogels reconstructed from cellulose nanofibrils. The favorable performance is ascribed to the natural hierarchical honeycomb structure of wood. Oil can be selectively absorbed not only from below but also from above the water surface. High oil/water absorption capacity of both types of wood structures (delignified template and polymer-modified biocomposite) allows for applications in oil/water separation.

In situ template synthesis of hierarchical porous carbon used for high performance lithium-sulfur batteries

Hierarchical porous carbon (HPC) consists of micropores, mesopores and macrospores which are synthesized by in situ formation of template followed by acid etching. The obtained pores are three-dimensional and interconnected, and evenly distributed in the carbon matrix. By adjusting the ratio of the raw materials, the high specific surface area and large pore volume is afforded. The obtained HPC-3 samples possess graphite flakes and locally graphited-carbon walls, which provide good electrical conductivity. These unique characteristics make these materials suitable cathode scaffolds for Li-S batteries. After encapsulating 61% sulfur into HPC-3 host, the S/HPC-3 composite exhibits excellent cycling stability, high columbic efficiency, and superior rate cycling as a cathode material. The S/HPC-3 composite cathode displays an initial discharge capacity of 1059 mA h g-1, and a reversible capacity of 797 mA h g-1 after 200 cycles at 0.2C. The discharge capacities of the S/HPC-3 composite cathode after every 10 cycles at 0.1, 0.2, 0.5, 1, and 2C are 1119, 1056, 982, 921, and 829 mA h g-1, respectively.

Graphitic carbon-wrapped NiO embedded three dimensional nitrogen doped aligned carbon nanotube arrays with long cycle life for lithium ion batteries

In this work, a three-dimensional nitrogen doped aligned carbon nanotube array (NACNTs)@NiO@graphitic carbon composite was fabricated by an effective strategy involving nebulized ethanol assisted infiltration, In this structure, the NiO nanoparticles were wrapped by graphitic carbon layers and NiO@graphitic carbon core–shell nanoparticles adhered strictly to the surface of NACNTs to form a highly ordered 3D structure. When this composite was used as an anode for lithium ion batteries, the well-ordered pore of its NACNTs can facilitate the electrolyte to penetrate and improve electronic conductivity. At the same time, the graphitic layers can promote the stability of a solid electrolyte interface film. Therefore, the NACNTs@NiO@graphitic carbon composite containing 68.1 wt% NiO delivers excellent capacity retention of 91.6% after 200 cycles at 0.2C.

NACNTs@NiO@graphitic carbon composites were synthesized with the help of nebulizing. The outstanding performances are attributed to the original structure of NACNTs@NiO@graphitic carbon.

Hierarchical NiO nanobelt film array as an anode for lithium-ion batteries with enhanced electrochemical performance

In this study, an ultrathin 2-dimensional hierarchical nickel oxide nanobelt film array was successfully assembled and grown on a Ni substrate as a binder-free electrode material for lithium ion batteries.

Tunable multimodal adhesion of 3D, nanocrystalline CoFe2O4 pollen replicas

3D replicas of sunflower pollen microparticles, comprised of a multicomponent magnetic spinel ferrite (CoFe₂O₄) with tailorable adhesive properties, have been synthesized for the first time via a conformal layer-by-layer (LbL) surface sol-gel (SSG) deposition process followed by organic pyrolysis and oxide compound formation at a peak temperature of 600 °C-900 °C. These high-fidelity ferrite pollen replicas exhibited multimodal (van der Waals, vdW, and magnetic) adhesion that could be tuned via control of the CoFe₂O₄ nanoparticle and crystal sizes. The CoFe₂O₄ pollen replicas exhibited a non-monotonic change in short-range (~10 nm) vdW adhesion with an increase in the peak firing temperature, which was consistent with the counteracting effects of particle coarsening on the size and number of nanoparticles present on the sharp tips of the echini (spines) on the pollen replica surfaces. The longer-range (up to ~1 mm) magnetic force of adhesion increased monotonically with an increase in firing temperature, which was consistent with the observed increases in the values of the saturation and remanent magnetization of CoFe₂O₄ with an increase in average nanocrystal size. By adjusting the nanocrystal/nanoparticle sizes of the CoFe₂O₄ pollen replicas, the total force of adhesion (vdW  +  magnetic) to a magnetic substrate could be increased by a factor of ~3 relative to native pollen grains.

Confining Sulfur in N-Doped Porous Carbon Microspheres Derived from Microalgaes for Advanced Lithium-Sulfur Batteries

Lithium-sulfur (Li-S) battery is one of the most attractive candidates for the next-generation energy storage system. However, the intrinsic insulating nature of sulfur and the notorious polysulfide shuttle are the major obstacles, which hinder the commercial application of Li-S battery. Confining sulfur into conductive porous carbon matrices with designed polarized surfaces is regarded as a promising and effective strategy to overcome above issues. Herein, we propose to use microalgaes (Schizochytrium sp.) as low-cost, renewable carbon/nitrogen precursors and biological templates to synthesize N-doped porous carbon microspheres (NPCMs). These rational designed NPCMs can not only render the sulfur-loaded NPCMs (NPCSMs) composites with high electronic conductivity and sulfur content, but also greatly suppress the diffusion of polysulfides by strongly physical and chemical adsorptions. As a result, NPCSMs cathode demonstrates a superior reversible capacity (1030.7 mA h g^-1) and remarkable capacity retention (91%) at 0.1 A g^-1 after 100 cycles. Even at an extremely high current density of 5 A g^-1, NPCSMs still can deliver a satisfactory discharge capacity of 692.3 mAh g^-1. This work reveals a sustainable and effective biosynthetic strategy to fabricate N-doped porous carbon matrices for high performance sulfur cathode in Li-S battery, as well as offers a fascinating possibility to rationally design and synthesize novel carbon-based composites.

Tuning the Shell Number of Multishelled Metal Oxide Hollow Fibers for Optimized Lithium-Ion Storage

Searching the long-life transition-metal oxide (TMO)-based materials for future lithium-ion batteries (LIBs) is still a great challenge because of the mechanical strain resulting from volume change of TMO anodes during the lithiation/delithiation process. To well address this challenging issue, we demonstrate a controlled method for making the multishelled TMO hollow microfibers with tunable shell numbers to achieve the optimal void for efficient lithium-ion storage. Such a particularly designed void can lead to a short diffusion distance for fast diffusion of Li⁺ ions and also withstand a large volume variation upon cycling, both of which are the key for high-performance LIBs. Triple-shelled TMO hollow microfibers are a quite stable anode material for LIBs with high reversible capacities (NiO: 698.1 mA h g^-1 at 1 A g^-1; Co₃O₄: 940.2 mA h g^-1 at 1 A g^-1; Fe₂O₃: 997.8 mA h g^-1 at 1 A g^-1), excellent rate capability, and stability. The present work opens a way for rational design of the void of multiple shells in achieving the stable lithium-ion storage through the biomass conversion strategy.

Cost-effective synthesis of bamboo-structure carbon nanotubes from coal for reversible lithium storage

Carbon nanotubes (CNTs) with special structures offers great benefits for energy storage applications.

Inflated Sporopollenin Exine Capsules Obtained from Thin-Walled Pollen

Sporopollenin is a physically robust and chemically resilient biopolymer that comprises the outermost layer of pollen walls and is the first line of defense against harsh environmental conditions. The unique physicochemical properties of sporopollenin increasingly motivate the extraction of sporopollenin exine capsules (SECs) from pollen walls as a renewable source of organic microcapsules for encapsulation applications. Despite the wide range of different pollen species with varying sizes and wall thicknesses, faithful extraction of pollen-mimetic SECs has been limited to thick-walled pollen capsules with rigid mechanical properties. There is an unmet need to develop methods for producing SECs from thin-walled pollen capsules which constitute a large fraction of all pollen species and have attractive materials properties such as greater aerosol dispersion. Herein, we report the first successful extraction of inflated SEC microcapsules from a thin-walled pollen species (Zea mays), thereby overcoming traditional challenges with mechanical stability and loss of microstructure. Morphological and compositional characterization of the SECs obtained by the newly developed extraction protocol confirms successful protein removal along with preservation of nanoscale architectural features. Looking forward, there is excellent potential to apply similar strategies across a wide range of unexplored thin-walled pollen species.

Flexible NiO-Graphene-Carbon Fiber Mats Containing Multifunctional Graphene for High Stability and High Specific Capacity Lithium-Ion Storage

An electrode's conductivity, ion diffusion rate, and flexibility are critical factors in determining its performance in a lithium-ion battery. In this study, NiO-carbon fibers were modified with multifunctional graphene sheets, resulting in flexible mats. These mats displayed high conductivities, and the transformation of active NiO to inert Ni(0) was effectively prevented at relatively low annealing temperatures in the presence of graphene. The mats were also highly flexible and contained large gaps for the rapid diffusion of ions, because of the addition of graphene sheets. The flexible NiO-graphene-carbon fiber mats achieved a reversible capacity of 750 mA h/g after 350 cycles at a current density of 500 mA/g as the binder-free anodes of lithium-ion batteries. The mats' rate capacities were also higher than those of either the NiO-carbon fibers or the graphene-carbon fibers. This work should provide a new route toward improving the mechanical properties, conductivities, and stabilities of mats using multifunctional graphene.

Transition Metal Carbides and Nitrides in Energy Storage and Conversion

High-performance electrode materials are the key to advances in the areas of energy conversion and storage (e.g., fuel cells and batteries). In this Review, recent progress in the synthesis and electrochemical application of transition metal carbides (TMCs) and nitrides (TMNs) for energy storage and conversion is summarized. Their electrochemical properties in Li-ion and Na-ion batteries as well as in supercapacitors, and electrocatalytic reactions (oxygen evolution and reduction reactions, and hydrogen evolution reaction) are discussed in association with their crystal structure/morphology/composition. Advantages and benefits of nanostructuring (e.g., 2D MXenes) are highlighted. Prospects of future research trends in rational design of high-performance TMCs and TMNs electrodes are provided at the end.

Biomimetic and Bioinspired Synthesis of Nanomaterials/Nanostructures

In recent years, due to its unparalleled advantages, the biomimetic and bioinspired synthesis of nanomaterials/nanostructures has drawn increasing interest and attention. Generally, biomimetic synthesis can be conducted either by mimicking the functions of natural materials/structures or by mimicking the biological processes that organisms employ to produce substances or materials. Biomimetic synthesis is therefore divided here into "functional biomimetic synthesis" and "process biomimetic synthesis". Process biomimetic synthesis is the focus of this review. First, the above two terms are defined and their relationship is discussed. Next different levels of biological processes that can be used for process biomimetic synthesis are compiled. Then the current progress of process biomimetic synthesis is systematically summarized and reviewed from the following five perspectives: i) elementary biomimetic system via biomass templates, ii) high-level biomimetic system via soft/hard-combined films, iii) intelligent biomimetic systems via liquid membranes, iv) living-organism biomimetic systems, and v) macromolecular bioinspired systems. Moreover, for these five biomimetic systems, the synthesis procedures, basic principles, and relationships are discussed, and the challenges that are encountered and directions for further development are considered.

From Allergens to Battery Anodes: Nature-Inspired, Pollen Derived Carbon Architectures for Room- and Elevated-Temperature Li-ion Storage

The conversion of allergic pollen grains into carbon microstructures was carried out through a facile, one-step, solid-state pyrolysis process in an inert atmosphere. The as-prepared carbonaceous particles were further air activated at 300 °C and then evaluated as lithium ion battery anodes at room (25 °C) and elevated (50 °C) temperatures. The distinct morphologies of bee pollens and cattail pollens are resembled on the final architecture of produced carbons. Scanning Electron Microscopy images shows that activated bee pollen carbon (ABP) is comprised of spiky, brain-like, and tiny spheres; while activated cattail pollen carbon (ACP) resembles deflated spheres. Structural analysis through X-ray diffraction and Raman spectroscopy confirmed their amorphous nature. X-ray photoelectron spectroscopy analysis of ABP and ACP confirmed that both samples contain high levels of oxygen and small amount of nitrogen contents. At C/10 rate, ACP electrode delivered high specific lithium storage reversible capacities (590 mAh/g at 50 °C and 382 mAh/g at 25 °C) and also exhibited excellent high rate capabilities. Through electrochemical impedance spectroscopy studies, improved performance of ACP is attributed to its lower charge transfer resistance than ABP. Current studies demonstrate that morphologically distinct renewable pollens could produce carbon architectures for anode applications in energy storage devices.

Fabricating three-dimensional mesoporous carbon network-coated LiFePO4/Fe nanospheres using thermal conversion of alginate-biomass

Three-dimensional mesoporous carbon network-coated LiFePO₄/Fe nanospheres with high-rate capability.

Supercritical fluid assisted biotemplating synthesis of Si–O–C microspheres from microalgae for advanced Li-ion batteries

Si–O–C microspheres were synthesized from microalgaes served as biological templates and carbon sources with the assistance of supercritical CO₂ fluid. As anodic materials, Si–O–C microspheres exhibited remarkable electrochemical performance.

Engineered nanomembranes for smart energy storage devices

This review presents recent progress in engineered tubular and planar nanomembranes for smart energy storage applications, especially related to the investigation of fundamental electrochemical kinetics.

Applications of hierarchically structured porous materials from energy storage and conversion, catalysis, photocatalysis, adsorption, separation, and sensing to biomedicine

A comprehensive review of the recent progress in the applications of hierarchically structured porous materials is given.