Polyethylene Glycol-b-poly(trialkylsilyl methacrylate-co-methyl methacrylate) Hydrolyzable Block Copolymers for Eco-Friendly Self-Polishing Marine Coatings

Hydrolyzable block copolymers consisting of a polyethylene glycol (PEG) first block and a random poly(trialkylsilyl methacrylate (TRSiMA, R = butyl, isopropyl)-co-methyl methacrylate (MMA)) second block were synthesized by RAFT polymerization. Two PEGs with different molar masses (M_n = 750 g/mol (PEG1) and 2200 g/mol (PEG2)) were used as macro-chain transfer agents and the polymerization conditions were set in order to obtain copolymers with a comparable mole content of trialkylsilyl methacrylate (~30 mole%) and two different PEG mole percentages of 10 and 30 mole%. The hydrolysis rates of PEG-b-(TRSiMA-co-MMA) in a THF/basic (pH = 10) water solution were shown to drastically depend on the nature of the trialkylsilyl groups and the mole content of the PEG block. Films of selected copolymers were also found to undergo hydrolysis in artificial seawater (ASW), with tunable erosion kinetics that were modulated by varying the copolymer design. Measurements of the advancing and receding contact angles of water as a function of the immersion time in the ASW confirmed the ability of the copolymer film surfaces to respond to the water environment as a result of two different mechanisms: (i) the hydrolysis of the silylester groups that prevailed in TBSiMA-based copolymers; and (ii) a major surface exposure of hydrophilic PEG chains that was predominant for TPSiMA-based copolymers. AFM analysis revealed that the surface nano-roughness increased upon immersion in ASW. The erosion of copolymer film surfaces resulted in a self-polishing, antifouling behavior against the diatom Navicula salinicola. The amount of settled diatoms depended on the hydrolysis rate of the copolymers.

Degradable hyaluronic acid/chitosan polyelectrolyte multilayers with marine fouling-release properties

Polysaccharide multilayers consisting of hyaluronic acid and chitosan were prepared by layer-by-layer assembly. To be used in seawater, the multilayers were crosslinked to a different degree using thermal or chemical methods. ATR-FTIR revealed different amide densities as a result of the crosslinking conditions. AFM showed that the crosslinking affected the roughness and swelling behavior of the coatings. The stability and degradability of the multilayers in aqueous environments were monitored with spectroscopic ellipsometry. The resistance of the coatings against non-specific protein adsorption was characterized by SPR spectroscopy. Settlement assays using Ulva linza zoospores and removal assays using the diatom Navicula incerta showed that the slowly degradable coatings were less prone to fouling than the strongly crosslinked ones. Thus, the coatings were a suitable model system to show that crosslinking the multilayers under mild conditions and equipping the coatings with controlled degradation rates enhances their antifouling and fouling-release properties against marine fouling organisms.

Latest research progress of marine microbiological corrosion and bio-fouling, and new approaches of marine anti-corrosion and anti-fouling

Marine resources and industry have become one of the most important pillars in economic development all over the world. However, corrosion of materials is always the most serious problem to the infrastructure and equipment served in marine environment. Researchers have found that microbiologically influenced corrosion (MIC) and marine bio-fouling are two main mechanisms of marine corrosions due to the complicated marine environment and marine organisms. This article summarized the latest research progress about these two mechanisms and indicated that both MIC and marine bio-fouling are closely related to the biofilms on material surfaces formed by the marine microorganisms and their metabolites. As a result, to prevent the occurrence of MIC and bio-fouling, it is important to control the microorganisms in biofilms or prevent the adhesion and formation of biofilms. The traditional method of using chemical bactericide or antifoulant faces the problems of pollution and microorganism resistance. This article introduced four research approaches about the new tendency of applying new materials and technologies to cooperate with traditional chemicals to achieve better and longer effects with lower environment pollution through synergistic actions. Finally, some future research tendencies were proposed for whole marine anti-corrosion and anti-fouling areas.

Self-Generating and Self-Renewing Zwitterionic Polymer Surfaces for Marine Anti-Biofouling

Regeneration of antifouling polymer surfaces after contamination or damage is an important issue, especially in complex marine environments. Here, inspired by the self-renewal of silyl acrylate polymers and the protein resistance of zwitterionic polymers, we prepared a novel hydrolysis-induced zwitterionic monomer, tertiary carboxybetaine triisopropylsilyl ester ethyl acrylate (TCBSA), and copolymerized it with methyl methacrylate (MMA). Such a copolymer rapidly self-generates a zwitterionic surface and provides fouling resistance in marine environments. Furthermore, TCBSA was copolymerized with MMA and 2-methylene-1,3-dioxepane (MDO), where MDO causes degradation of the polymers. Our study demonstrates that the degradation of the polymer is controlled, and the degradation rate increases with the external enzyme concentration in the seawater, leading to a self-renewing dynamic surface. Quartz crystal microbalance with dissipation measurements show that the polymeric coating with self-generating zwitterions has excellent protein resistance in seawater. Bioassays demonstrate that the coating can effectively inhibit the adhesion of marine bacteria (Pseudomonas sp.) and diatoms (Navicula incerta). The coating with a self-generating and self-renewing zwitterionic surface is potential to find applications in marine anti-biofouling.

Hydrolyzable Additive-Based Silicone Elastomers: A New Approach for Antifouling Coatings

Fouling Release Coatings are marine antifouling coatings based on silicone elastomers. Contrary to commonly used biocide-based antifouling coatings, they do not release biocides into the marine environment, however, they suffer from poor antifouling efficacy during idle periods. To improve their antifouling performances in static conditions, various amounts of hydrolyzable polymers were incorporated within a silicone matrix. These hydrolyzable polymers were chosen for the well-known hydrolytic degradation mechanism of their main chain, e.g. poly(ε-caprolactone) (PCL), or of their ester pending groups, e.g. poly(bis(trimethylsilyloxy)methylsilyl methacrylate) (PMATM2). The degradation kinetics of such hydrolyzable silicone coatings were assessed by mass loss measurements during immersion in deionized water. Coatings containing PMATM2 exhibited a maximum mass loss after 12 weeks, whereas PCL-based coatings showed no significant mass loss after 24 weeks. Dynamic contact angle measurements revealed the modifications of the coatings surface chemistry with an amphiphilic behavior after water exposure. The attachment of macrofoulers on these coatings were evaluated by field tests in the Mediterranean Sea, demonstrating the short or long-term antifouling effect of these hydrolyzable polymers embedded in the silicone matrix. The settlement of A. amphitrite barnacles on the different coatings indicated inhospitable behaviors towards larval barnacles for coatings with at least 15 wt % of additives.

Dynamic surface antifouling: mechanism and systems

Marine biofouling is a global problem today. High efficiency and eco-friendly antifouling systems are in pressing need. In recent years, we have proposed the concept of dynamic surface antifouling (DSA). That is, a continuously changing surface can effectively prevent marine fouling organisms from landing and adhesion. Based on this strategy, we developed coatings with dynamic surfaces by using degradable polymers including polyester-polyurethane, modified polyester and poly(ester-co-acrylate). They exhibit tunable renewability, and excellent antifouling and mechanical performance. Moreover, the polymers can serve as carrier and controlled release systems of antifoulants so that they have long service life. This paper reviews the progress and trends in marine anti-biofouling, and presents the mechanism and systems of DSA.

Poly(ester)–poly(silyl methacrylate) copolymers: synthesis and hydrolytic degradation kinetics

Poly(MDO-silyl methacrylate) copolymers synthesized by RROP as promising degradable self-polishing copolymers (DSPC) for antifouling coatings.

Phenotypic Heterogeneity in Attachment of Marine Bacteria toward Antifouling Copolymers Unraveled by AFM

Up to recent years, bacterial adhesion has mostly been evaluated at the population level. Single cell level has improved in the past few years allowing a better comprehension of the implication of individual behaviors as compared to the one of a whole community. A new approach using atomic force microscopy (AFM) to measure adhesion forces between a live bacterium attached via a silica microbead to the AFM tipless cantilever and the surface has been recently developed. The objectives of this study is to examine the bacterial adhesion to a surface dedicated to ship hulls at the population and the cellular level to understand to what extent these two levels could be correlated. Adhesion of marine bacteria on inert surfaces are poorly studied in particular when substrata are dedicated to ship hulls. Studying these interactions in this context are worthwhile as they may involve different adhesion behaviors, taking place in salty conditions, using different surfaces than the ones usually utilized in the literacy. FRC (fouling release coatings)-SPC (self-polishing coatings) hybrids antifouling coatings have been used as substrata and are of particular interest for designing environmentally friendly surfaces, combining progressive surface erosion and low adhesion properties. In this study, a hybrid coating has been synthetized and used to study the adhesion of three marine bacteria, displaying different surface characteristics, using microplate assays associated with confocal scanning laser microscopy (CSLM) and AFM. This study shows that the bacterial strain that appeared to have the weakest adhesion and biofilm formation abilities when evaluated at the population level using microplates assays and CSLM, displayed stronger adhesion forces on the same surfaces at the single cell level using AFM. In addition, one of the strains tested which presented a strong ability to adhere and to form biofilm at the population level, displayed a heterogeneous phenotypic behavior at the single cell level. Therefore, these results suggest that the evaluation of adhesion at the population level cannot always be correlated with adhesion forces measured individually by AFM and that some bacteria are prone to phenotypic heterogeneity among their population.

Facile synthesis of graft copolymers of controlled architecture. Copolymerization of fluorinated and non-fluorinated poly(dimethylsiloxane) macromonomers with trialkylsilyl methacrylates using RAFT polymerization

The synthesis and spectroscopic characterization of a new family of statistical and diblock graft copolymers is described.

Poly(dimethylsiloxane)-Based Polyurethane with Chemically Attached Antifoulants for Durable Marine Antibiofouling

Marine biofouling is a problem for marine industry and maritime activities. We have prepared polyurethane with poly(dimethylsiloxane) (PDMS) main chains and N-(2,4,6-trichlorophenyl) maleimide (TCM) pendant groups via a combination of a thiol-ene click reaction and a condensation reaction and studied its properties. The polymer has low surface energy and a high water contact angle. When TCM content in bulk is high enough, sufficient antifoulant groups can be exposed on the surface. Our study reveals that such polymeric surface can effectively inhibit the adhesion and colonization of marine organisms such as bacteria (Micrococcus luteus), diatom Navicula, and barnacle cyprids. Particularly, marine field tests demonstrate that the polymer has excellent antibiofouling performance in 110 days.