Optical properties and radiative forcing of carbonaceous aerosols in a valley city under persistent high temperature

Carbonaceous aerosols were collected in the valley city of Baoji city in Northern China in August 2022. The light absorption characteristics and influencing factors of black carbon (BC) and brown carbon (BrC) were analyzed, and their radiative forcing was estimated. The results showed that the light absorption of secondary brown carbon [AbsBrC,sec (370)] was 7.5 ± 2.4 Mm-1, which was 2.5 times that of primary brown carbon [AbsBrC,pri (370), 3.0 ± 1.2 Mm-1]. During the study period, the absorption Ångström exponent (AAE) of aerosol was 1.6, indicating that there was obvious secondary aerosol formation or carbonaceous aerosol aging in the valley city of Baoji. Except for secondary BrC (BrCsec), the light absorption coefficient (Abs) and mass absorption efficiency (MAE) of BC and primary BrC (BrCpri) during the persistent high temperature period (PHT) were higher than those during the normal temperature period (NT) and the precipitation period (PP), which indicated that the light absorption capacity of black carbon and primary brown carbon increased, while the light absorption capacity of secondary brown carbon decreased under persistent high temperature period. Secondary aerosols sulfide (SO42-), nitrate (NO3-) and secondary organic carbon (SOC) are important factors for promoting the light absorption enhancemen of BC and BrCpri and photobleaching of BrCsec during persistent high temperature period. The Principal Component Analysis-Multiple Linear Regression (PCA-MLR) model showed that traffic emissions was the most important source of pollution in Baoji City. Based on this, the secondary source accelerates the aging of BC and BrC, causing changes in light absorption. During PHT, the radiative forcing of BC and BrCpri were enhanced, while the radiative forcing of BrCsec was weakened, but the positive radiative forcing generated by them may aggravate the high-temperature disaster.

Enhanced Light Absorption and Elevated Viscosity of Atmospheric Brown Carbon through Evaporation of Volatile Components

Samples of brown carbon (BrC) material were collected from smoke emissions originating from wood pyrolysis experiments, serving as a proxy for BrC representative of biomass burning emissions. The acquired samples, referred to as "pyrolysis oil (PO1)," underwent subsequent processing by thermal evaporation of their volatile compounds, resulting in a set of three additional samples with volume reduction factors of 1.33, 2, and 3, denoted as PO1.33, PO2, and PO3. The chemical compositions of these POx samples and their BrC chromophore features were analyzed using a high-performance liquid chromatography instrument coupled with a photodiode array detector and a high-resolution mass spectrometer. The investigation revealed a noteworthy twofold enhancement of BrC light absorption observed for the progression of PO1 to PO3 samples, assessed across the spectral range of 300-500 nm. Concurrently, a decrease in the absorption Ångstrom exponent (AAE) from 11 to 7 was observed, indicating a weaker spectral dependence. The relative enhancement of BrC absorption at longer wavelengths was more significant, as exemplified by the increased mass absorption coefficient (MAC) measured at 405 nm from 0.1 to 0.5 m2/g. Molecular characterization further supports this darkening trend, manifesting as a depletion of small oxygenated, less absorbing monoaromatic compounds and the retention of relatively large, less polar, more absorbing constituents. Noteworthy alterations of the PO1 to PO3 mixtures included a reduction in the saturation vapor pressure of their components and an increase in viscosity. These changes were quantified by the mean values shifting from approximately 1.8 × 103 μg/m3 to 2.3 μg/m3 and from ∼103 Pa·s to ∼106 Pa·s, respectively. These results provide quantitative insights into the extent of BrC aerosol darkening during atmospheric aging through nonreactive evaporation. This new understanding will inform the refinement of atmospheric and chemical transport models.

Chemical and Light-Absorption Properties of Water-Soluble Organic Aerosols in Northern California and Photooxidant Production by Brown Carbon Components

Atmospheric brown carbon (BrC) can impact the radiative balance of the earth and form photooxidants. However, the light absorption and photochemical properties of BrC from different sources remain poorly understood. To address this gap, dilute water extracts of particulate matter (PM) samples collected at Davis, CA over one year were analyzed using high resolution aerosol mass spectrometry (HR-AMS) and UV-vis spectroscopy. Positive matrix factorization (PMF) on combined AMS and UV-vis data resolved five water-soluble organic aerosol (WSOA) factors with distinct mass spectra and UV-vis spectra: a fresh and an aged water-soluble biomass burning OA (_WSBBOA_fresh and _WSBBOA_aged) and three oxygenated OA (_WSOOAs). _WSBBOA_fresh is the most light-absorbing, with a mass absorption coefficient (MAC_365 nm) of 1.1 m² g^-1, while the _WSOOAs are the least (MAC_365 nm = 0.01-0.1 m² g^-1). These results, together with the high abundance of _WSBBOAs (∼52% of the WSOA mass), indicate that biomass burning activities such as residential wood burning and wildfires are an important source of BrC in northern California. The concentrations of aqueous-phase photooxidants, i.e., hydroxyl radical (·OH), singlet molecular oxygen (¹O₂*), and oxidizing triplet excited states of organic carbon (³C*), were also measured in the PM extracts during illumination. Oxidant production potentials (PP_OX) of the five WSOA factors were explored. The photoexcitation of BrC chromophores from BB emissions and in OOAs is a significant source of ¹O₂* and ³C*. By applying our PP_OX values to archived AMS data at dozens of sites, we found that oxygenated organic species play an important role in photooxidant formation in atmospheric waters.

Global brown carbon emissions from combustion sources

Light-absorbing organic carbon (OC), sometimes known as Brown Carbon (BrC), has been recognized as an important fraction of carbonaceous aerosols substantially affecting radiative forcing. This study firstly developed a bottom-up estimate of global primary BrC, and discussed its spatiotemporal distribution and source contributions from 1960 to 2010. The global total primary BrC emission from both natural and anthropogenic sources in 2010 was 7.26 (5.98-8.93 as an interquartile range) Tg, with 43.5% from anthropogenic sources. High primary BrC emissions were in regions such as Africa, South America, South and East Asia with natural sources (wild fires and deforestation) contributing over 70% in the former two regions, while in East Asia, anthropogenic sources, especially residential solid fuel combustion, accounted for over 80% of the regional total BrC emissions. Globally, the historical trend was mainly driven by anthropogenic sources, which increased from 1960 to 1990 and then started to decline. Residential emissions significantly impacted on emissions and temporal trends that varied by region. In South and Southeast Asia, the emissions increased obviously due to population growth and a slow transition from solid fuels to clean modern energies in the residential sector. It is estimated that in primary OC, the global average was about 20% BrC, but this ratio varied from 13% to 47%, depending on sector and region. In areas with high residential solid fuel combustion emissions, the ratio was generally twice the value in other areas. Uncertainties in the work are associated with the concept of BrC and measurement technologies, pointing to the need for more studies on BrC analysis and quantification in both emissions and the air.

The reaction of acetaldehyde, glyoxal, and ammonia to yield 2-methylimidazole: thermodynamic and kinetic analyses of the mechanism

The most thermodynamically and kinetically favorable pathways for the formation of 2-methylimidazole (2MI) in the reaction of glyoxal and acetaldehyde with ammonia in aqueous solution have been determined. The formation of 2MI proceeds through a number of successive intermediates of acyclic and cyclic structures, and the most favorable route (thermodynamically and kinetically) for the formation of the imidazole ring is the condensation of amine intermediates, in contrast to the existing concepts of imine structures. The limiting stage is the stage of cyclization involving the intramolecular attack by the amino group of the precyclic intermediate on the carbon atom bound to the hydroxyl group with the simultaneous release of a water molecule according to the S_N2 mechanism. Further stages of stepwise dehydration lead to the formation of a cyclic diazine, the intramolecular migration of the proton of the tertiary carbon atom to the nitrogen atom of which completes the formation of 2MI. Experimental studies on the effect of the order of mixing of initial reagents on the 2MI yield confirmed the quantum-chemically substantiated favorable pathway for the formation of 2MI during the interaction of amine intermediates, and also revealed that the selectivity of the 2MI formation is achieved by successive mixing of acetaldehyde with ammonia until the formation of hydroxyamine products and their further interaction with glyoxal.

High-Resolution Fluorescence Spectra of Airborne Biogenic Secondary Organic Aerosols: Comparisons to Primary Biological Aerosol Particles and Implications for Single-Particle Measurements

Aqueous extracts of biogenic secondary organic aerosols (BSOAs) have been found to exhibit fluorescence that may interfere with the laser/light-induced fluorescence (LIF) detection of primary biological aerosol particles (PBAPs). In this study, we quantified the interference of BSOAs to PBAPs by directly measuring airborne BSOA particles, rather than aqueous extracts. BSOAs were generated by the reaction of d-limonene (LIM) or α-pinene (PIN) and ozone (O₃) with or without ammonia in a chamber under controlled conditions. With an excitation wavelength of 355 nm, BSOAs exhibited peak emissions at 464-475 nm, while fungal spores exhibited peak emissions at 460-483 nm; the fluorescence intensity of BSOAs with diameters of 0.7 μm was in the same order of magnitude as that of fungal spores with diameters of 3 μm. The number fraction of 0.7 μm BSOAs that exhibited fluorescence above the threshold was in the range of 1.9-15.9%, depending on the species of precursors, relative humidity (RH), and ammonia. Similarly, the number fraction of 3 μm fungal spores that exhibited fluorescence above the threshold was 4.9-36.2%, depending on the species of fungal spores. Normalized fluorescence by particle volumes suggests that BSOAs exhibited fluorescence in the same order of magnitude as pollen and 10-100 times higher than that of fungal spores. A comparison with ambient particles suggests that BSOAs caused significant interference to ambient fine particles (15 of 16 ambient fine particle measurements likely detected BSOAs) and the interference was smaller for ambient coarse particles (4 of 16 ambient coarse particle measurements likely detected BSOAs) when using LIF instruments.

Optical Properties of Secondary Organic Aerosol Produced by Nitrate Radical Oxidation of Biogenic Volatile Organic Compounds

Nighttime oxidation of biogenic volatile organic compounds (BVOCs) by nitrate radicals (NO₃·) represents one of the most important interactions between anthropogenic and natural emissions, leading to substantial secondary organic aerosol (SOA) formation. The direct climatic effect of such SOA cannot be quantified because its optical properties and atmospheric fate are poorly understood. In this study, we generated SOA from the NO₃· oxidation of a series BVOCs including isoprene, monoterpenes, and sesquiterpenes. The SOA were subjected to comprehensive online and offline chemical composition analysis using high-resolution mass spectrometry and optical properties measurements using a novel broadband (315-650 nm) cavity-enhanced spectrometer, which covers the wavelength range needed to understand the potential contribution of the SOA to direct radiative forcing. The SOA contained a significant fraction of oxygenated organic nitrates (ONs), consisting of monomers and oligomers that are responsible for the detected light absorption in the 315-400 nm range. The SOA created from β-pinene and α-humulene was further photochemically aged in an oxidation flow reactor. The SOA has an atmospheric photochemical bleaching lifetime of >6.2 h, indicating that some of the ONs in the SOA may serve as atmosphere-stable nitrogen oxide sinks or reservoirs and will absorb and scatter incoming solar radiation during the daytime.

Chemical Composition and Molecular-Specific Optical Properties of Atmospheric Brown Carbon Associated with Biomass Burning

This study provides molecular insights into the light absorption properties of biomass burning (BB) brown carbon (BrC) through the chemical characterization of tar condensates generated from heated wood pellets at oxidative and pyrolysis conditions. Both liquid tar condensates separated into "darker oily" and "lighter aqueous" immiscible phases. The molecular composition of these samples was investigated using reversed-phase liquid chromatography coupled with a photodiode array detector and a high-resolution mass spectrometer. The results revealed two sets of BrC chromophores: (1) common to all four samples and (2) specific to the "oily" fractions. The common BrC chromophores consist of polar, monoaromatic species. The oil-specific BrC chromophores include less-polar and nonpolar polyaromatic compounds. The most-light-absorbing pyrolysis oily phase (PO) was aerosolized and size-separated using a cascade impactor to compare the composition and optical properties of the bulk versus the aerosolized BrC. The mass absorption coefficient (MAC_300-500 nm) of aerosolized PO increased compared to that of the bulk, due to gas-phase partitioning of more volatile and less absorbing chromophores. The optical properties of the aerosolized PO were consistent with previously reported ambient BB BrC measurements. These results suggest the darkening of atmospheric BrC following non-reactive evaporation that transforms the optical properties and composition of aged BrC aerosols.

Effect of chemical structure on optical properties of secondary organic aerosols derived from C12 alkanes

With the development of the economy, anthropogenic emissions in the atmospheric environment increases, and air pollution has caused wide public concern. Vehicle exhaust is an important emission source in the atmosphere, and alkanes are the representative components in it. In this study, the optical properties of secondary organic aerosol (SOA) derived from several C₁₂ alkanes (2-methylundecane, hexylcyclohexane, and cyclododecane) in the absence of NO_X were determined. Absorption (imaginary part of the refractive index (RI), k) at 532 nm was negligible for all the derived SOA, and the scattering (real part of RI, n) of the SOA at 532 nm followed the order of cyclododecane SOA < hexylcyclohexane SOA < 2-methylundecane SOA, at both room- (25 °C) and low- (5 °C) temperature. The chemical compositions of the SOA formed were analyzed with an electrospray ionization time-of-flight mass spectrometer (ESI-TOF-MS). The mass spectra showed that the oligomers were generated in the reactions. It was shown that the different reaction pathways (due to various alkane structures) leaded to the difference in SOA chemical composition, which changed the RI values. The low-temperature condition promoted the progress of the oligomerization reaction so that the final RI values also changed. This work suggested that when estimating the radiative forcing of SOA using regional or global models, the structure of the precursors and reaction conditions should be taken into account.

Investigation of Primary and Secondary Particulate Brown Carbon in Two Chinese Cities of Xi'an and Hong Kong in Wintertime

Brown carbon (BrC), an aerosol carbonaceous matter component, impacts atmospheric radiation and global climate because of its absorption in the near-ultraviolet-visible region. Simultaneous air sampling was conducted in two megacities of Xi'an (northern) and Hong Kong (southern) in China in winter of 2016-2017. The aim of this study is to determine and characterize the BrC compounds in collected filter samples. Characteristic absorption peaks corresponding to aromatic C-C stretching bands, organo-nitrates, and C═O functional groups were seen in spectra of Xi'an samples, suggesting that the BrC was derived from freshly smoldering biomass and coal combustion as well as aqueous formation of anthropogenic secondary organic carbon. In Hong Kong, the light absorption of secondary BrC accounted for 76% of the total absorbances of BrC. The high abundance of strong C═O groups, biogenic volatile organic compounds (BVOCs) and atmospheric oxidants suggest secondary BrC was likely formed from photochemical oxidation of BVOCs in Hong Kong. Several representative BrC molecular markers were detected using Fourier transform ion cyclotron resonance mass spectrometry and their absorption properties were simulated by quantum chemistry. The results demonstrate that light absorption capacities of secondary anthropogenic BrC with nitro-functional groups were stronger than those of biogenic secondary BrC and anthropogenic primary BrC.

Improving the accuracy and precision of broadband optical cavity measurements

Most extinction measurements require a stable light source to attain high precision and accuracy. Here, we present a convenient approach to normalize light source intensity in broadband optical cavity measurements. In the absence of sample extinction, we show that the in-band signal - the high finesse spectral region of the optical cavity in which sample extinction is measured with high sensitivity - is strongly correlated with the out-of-band signal. The out-of-band signal is insensitive to sample extinction and can act as a proxy for light source intensity. This normalization approach strongly suppressed in-band intensity changes in two incoherent broadband cavity-enhanced absorption spectroscopy (IBBCEAS) instruments with dissimilar light sources and optical cavity properties. Intensity fluctuations in an arc lamp system were suppressed by a factor of 7 to 16 and in the LED spectrometer by a factor of 10. This approach therefore improves the accuracy and precision of extinction measurements where either property is limited by the light source stability.

Theoretical analysis of glyoxal condensation with ammonia in aqueous solution

The reactions of glyoxal with ammonia, ammonium salts, and amines cause the formation of the secondary organic aerosol (SOA) components (imidazole and its derivatives) in the atmosphere. The interaction of glyoxal and ammonia in aqueous solution is a primary reaction for these processes, and the explanation of its mechanism will allow developing the methods to control the formation of the SOA components. A detailed mechanism for the formation of key intermediates, namely, ethanediimine, diaminoethanediol, and aminoethanetriol, required for the imidazole ring cyclization, is proposed, and its potential energy surface (PES) has been constructed. This mechanism includes the experimentally identified intermediate compounds and takes into account the conformational and hydration equilibria of glyoxal. The schemes are proposed for further conversion of the key intermediates to the products of condensation between glyoxal and ammonia in the aqueous solution, C-N cyclic oligomers, that were identified. The products are shown to correspond to low positions on the PES in terms of Gibbs free energy, from -30.8 to -68.3 kcal mol-1, which confirms the high probability of their formation. The preferable thermodynamic pathway for formation of the imidazole products does not comprise the conversion of the diimine intermediate with the participation of the proton, but rather the interaction of either the diaminoalcohol with glyoxal monohydrate or two monoamine derivatives between themeselves (aminoethantriol and aminohydroxyacetaldehyde).

Formation and Optical Properties of Brown Carbon from Small α-Dicarbonyls and Amines

Brown Carbon (BrC) aerosols scatter and absorb solar radiation, directly affecting the Earth's radiative budget. However, considerable uncertainty exists concerning the chemical mechanism leading to BrC formation and their optical properties. In this work, BrC particles were prepared from mixtures of small α-dicarbonyls (glyoxal and methylglyoxal) and amines (methylamine, dimethylamine, and trimethylamine). The absorption and scattering of BrC particles were measured using a photoacoustic extinctometer (405 and 532 nm), and the chemical composition of the α-dicarbonyl-amine mixtures was analyzed using orbitrap-mass spectrometry and thermal desorption-ion drift-chemical ionization mass spectrometry. The single scattering albedo for methylglyoxal-amine mixtures is smaller than that of glyoxal-amine mixtures and increases with the methyl substitution of amines. The mass absorption cross-section for methylglyoxal-amine mixtures is two times higher at 405 nm wavelength than that at 532 nm wavelength. The derived refractive indexes at the 405 nm wavelength are 1.40-1.64 for the real part and 0.002-0.195 for the imaginary part. Composition analysis in the α-dicarbonyl-amine mixtures reveals N-heterocycles as the dominant products, which are formed via multiple steps involving nucleophilic attack, steric hindrance, and dipole-dipole interaction between α-dicarbonyls and amines. BrC aerosols, if formed from the particle-phase reaction of methylglyoxal with methylamine, likely contribute to atmospheric warming.

Three-wavelength cavity-enhanced albedometer for measuring wavelength-dependent optical properties and single-scattering albedo of aerosols

The spectral dependence of aerosol light absorption (α_abs) and single-scattering albedo-[ω, defined as the ratio of the scattering (α_scat) and extinction coefficients (α_ext = α_abs + α_scat)]-has proven effective in classifying dominant aerosol types. It is also helpful in understanding aerosol sources, transformation, climate and environmental effects, testing aerosol models, and improving the retrieval accuracy of satellite and remote sensing data. Despite the significant progress that has been made with measurement of light absorption and ω, many of the reported instruments either operate at a fixed wavelength or can only measure a single optical parameter. Quantitative multi-parameter wavelength-dependent measurement remains a challenge. In this work, a three-wavelength cavity-enhanced albedometer was developed. The albedometer can measure multiple optical parameters, α_ext, α_scat, α_abs, and ω, at λ = 365, 532, and 660 nm, in real time. The instrument's performance was evaluated using four different type laboratory generated aerosols, including polystyrene latex spheres (PSL, non-absorbing); ammonium sulfate (AS, non-absorbing); suwannee river fulvic acid (SRFA, slightly absorbing; a proxy for light absorbing organic aerosol); and nigrosin (strongly absorbing).

Evolution of the Complex Refractive Index of Secondary Organic Aerosols during Atmospheric Aging

The wavelength-dependence of the complex refractive indices (RI) in the visible spectral range of secondary organic aerosols (SOA) are rarely studied, and the evolution of the RI with atmospheric aging is largely unknown. In this study, we applied a novel white light-broadband cavity enhanced spectroscopy to measure the changes in the RI (400-650 nm) of β-pinene and p-xylene SOA produced and aged in an oxidation flow reactor, simulating daytime aging under NO _x-free conditions. It was found that these SOA are not absorbing in the visible range, and that the real part of the RI, n, shows a slight spectral dependence in the visible range. With increased OH exposure, n first increased and then decreased, possibly due to an increase in aerosol density and chemical mean polarizability for SOA produced at low OH exposures, and a decrease in chemical mean polarizability for SOA produced at high OH exposures, respectively. A simple radiative forcing calculation suggests that atmospheric aging can introduce more than 40% uncertainty due to the changes in the RI for aged SOA.

Comparing Aerosol Refractive Indices Retrieved from Full Distribution and Size- and Mass-Selected Measurements

Refractive index retrievals (also termed inverse Mie methods or optical closure) have seen considerable use as a method to extract the refractive index of aerosol particles from measured optical properties. Retrievals of an aerosol refractive index use one of two primary methods: 1) measurements of the extinction, absorption and/or scattering cross-sections or efficiencies of size- (and mass-) selected particles for mass-mobility refractive index retrievals (MM-RIR) or 2) measurements of aerosol size distributions and a combination of the extinction, absorption and/or scattering coefficients for full distribution refractive index retrievals (FD-RIR). These two methods were compared in this study using pure and mixtures of ammonium sulfate (AS) and nigrosin aerosol, which constitute a non-absorbing and absorbing material, respectively. The results indicate that the retrieved complex refractive index values are correlated to the amount of nigrosin in the aerosol but can be highly variable with differences in the real and imaginary components that range between -0.002 and 0.216 and -0.013 and 0.086; the average and standard deviation of the differences are 0.046 ± 0.046 and 0.023 ± 0.033, respectively. Forward calculation of the optical properties yielded average absolute values of the relative deviation of ≈ 15 % and ≈ 26 % for FD-RIR data using the MM-RIR values and contrariwise. The range of retrieved refractive indices were used to calculate the normalized global average aerosol radiative forcing of a model accumulation mode remote continental aerosol. Deviations using the refractive indices of the pure materials range from 9 % to 32 % for AS and 27 % to 45 % for nigrosin. For mixtures of nigrosin and AS, deviations were all > 100 % and not always able to capture the correct direction of the forcing; i.e., positive versus negative.

A Role for 2-Methyl Pyrrole in the Browning of 4-Oxopentanal and Limonene Secondary Organic Aerosol

Reactions of ammonia or ammonium sulfate (AS) with carbonyls in secondary organic aerosol (SOA) produced from limonene are known to form brown carbon (BrC) with a distinctive absorption band at 505 nm. This study examined the browning processes in aqueous solutions of AS and 4-oxopentanal (4-OPA), which has a 1,4-dicarbonyl structural motif present in many limonene SOA compounds. Aqueous reactions of 4-OPA with AS were found to produce 2-methyl pyrrole (2-MP), which was detected by gas chromatography. While 2-MP does not absorb visible radiation, it can further react with 4-OPA eventually forming BrC compounds. This was demonstrated by reacting 2-MP with 4-OPA or limonene SOA, both of which produced BrC with absorption bands at 475 and 505 nm, respectively. The formation of BrC in the reaction of 4-OPA with AS and ammonium nitrate was greatly accelerated by evaporation of the solution suggesting an important role of the dehydration processes in BrC formation. 4-OPA was also found to produce BrC in aqueous reactions with a broad spectrum of amino acids and amines. These results suggest that 4-OPA may be the smallest atmospherically relevant compound capable of browning by the same mechanism as limonene SOA.

Development of an incoherent broad-band cavity-enhanced aerosol extinction spectrometer and its application to measurement of aerosol optical hygroscopicity

We report on the development of a blue light-emitting-diode-based incoherent broad-band cavity-enhanced absorption spectroscopy (IBBCEAS) instrument for the measurement of the aerosol extinction coefficient at λ=461  nm. With an effective absorption path length of 2.8 km, an optimum detection limit of 0.05  Mm^-1 (5×10^-10  cm^-1) was achieved with an averaging time of 84 s. The baseline drift of the developed spectrometer was about ±0.3  Mm^-1 over 2.5 h (1σ standard deviation). The performance of the system was evaluated with laboratory-generated monodispersed polystyrene latex (PSL) spheres. The retrieved complex refractive index of PSL agreed well with previously reported values. The relative humidity (RH) dependence of the aerosol extinction coefficient was measured using IBBCEAS. The measured extinction enhancement factor values for 200 nm dry ammonium sulphate particles at different RH were in good agreement with the modeled values. Field performance of the aerosol extinction spectrometer was demonstrated at the Hefei Radiation Observatory site.

Enhanced Light Scattering of Secondary Organic Aerosols by Multiphase Reactions

Secondary organic aerosol (SOA) plays a pivotal role in visibility and radiative forcing, both of which are intrinsically linked to the refractive index (RI). While previous studies have focused on the RI of SOA from traditional formation processes, the effect of multiphase reactions on the RI has not been considered. Here, we investigate the effects of multiphase processes on the RI and light-extinction of m-xylene-derived SOA, a common type of anthropogenic SOA. We find that multiphase reactions in the presence of liquid water lead to the formation of oligomers from intermediate products such as glyoxal and methylglyoxal, resulting in a large enhancement in the RI and light-scattering of this SOA. These reactions will result in increases in light-scattering efficiency and direct radiative forcing of approximately 20%-90%. These findings improve our understanding of SOA optical properties and have significant implications for evaluating the impacts of SOA on the rapid formation of regional haze, global radiative balance, and climate change.

Martin S, Zelenyuk A. The properties and behavior of α-pinene secondary organic aerosol particles exposed to ammonia under dry conditions

Chemical transformations and aging of secondary organic aerosol (SOA) particles can alter their physical and chemical properties, including particle morphology.

Optical Properties of Secondary Organic Aerosol from cis-3-Hexenol and cis-3-Hexenyl Acetate: Effect of Chemical Composition, Humidity, and Phase

Atmospheric aerosols play an important role in Earth's radiative balance directly, by scattering and absorbing radiation, and indirectly, by acting as cloud condensation nuclei (CCN). Atmospheric aerosol is dominated by secondary organic aerosol (SOA) formed by the oxidation of biogenic volatile organic compounds (BVOCs). Green leaf volatiles (GLVs) are a class of BVOCs that contribute to SOA, yet their role in the Earth's radiative budget is poorly understood. In this work we measured the scattering efficiency (at 450, 525, and 635 nm), absorption efficiency (between 190 and 900 nm), particle phase, bulk chemical properties (O:C, H:C), and molecular-level composition of SOA formed from the ozonolysis of two GLVs: cis-3-hexenol (HXL) and cis-3-hexenyl acetate (CHA). Both HXL and CHA produced SOA that was weakly absorbing, yet CHA-SOA was a more efficient absorber than HXL-SOA. The scatter efficiency of SOA from both systems was wavelength-dependent, with the stronger dependence exhibited by HXL-SOA, likely due to differences in particle size. HXL-SOA formed under both dry (10% RH) and wet (70% RH) conditions had the same bulk chemical properties (O:C), yet significantly different optical properties, which was attributed to differences in molecular-level composition. We have found that SOA derived from green leaf volatiles has the potential to affect the Earth's radiative budget, and also that bulk chemical properties can be insufficient to predict SOA optical properties.

Secondary brown carbon formation via the dicarbonyl imine pathway: nitrogen heterocycle formation and synergistic effects

We observe nitrogen heterocycles to be common secondary brown carbon chromophores formed by dicarbonylsviathe imine pathway, and synergistic effects in mixed dicarbonyl reaction systems.

Direct Analysis of Pharmaceutical Drugs Using Nano-DESI MS

Counterfeit pharmaceutical drugs imply an increasing threat to the global public health. It is necessary to have systems to control the products that reach the market and to detect falsified medicines. In this work, molecules in several pharmaceutical tablets were directly analyzed using nanospray desorption electrospray ionization mass spectrometry (nano-DESI MS). Nano-DESI is an ambient surface sampling technique which enables sampling of molecules directly from the surface of the tablets without any sample pretreatment. Both the active pharmaceutical ingredients (APIs) and some excipients were detected in all analyzed tablets. Principal component analysis was used to analyze mass spectral features from different tablets showing strong clustering between tablets with different APIs. The obtained results suggest nano-DESI MS as future tool for forensic analysis to discern APIs present in unknown tablet samples.

Molecular selectivity of brown carbon chromophores

Complementary methods of high-resolution mass spectrometry and microspectroscopy were utilized for molecular analysis of secondary organic aerosol (SOA) generated from ozonolysis of two structural monoterpene isomers: D-limonene SOA (LSOA) and α-pinene SOA (PSOA). The LSOA compounds readily formed adducts with Na(+) under electrospray ionization conditions, with only a small fraction of compounds detected in the protonated form. In contrast, a significant fraction of PSOA compounds appeared in the protonated form because of their increased molecular rigidity. Laboratory simulated aging of LSOA and PSOA, through conversion of carbonyls into imines mediated by NH3 vapors in humid air, resulted in selective browning of the LSOA sample, while the PSOA sample remained white. Comparative analysis of the reaction products in the aged LSOA and PSOA samples provided insights into chemistry relevant to formation of brown carbon chromophores. A significant fraction of carbonyl-imine conversion products with identical molecular formulas was detected in both samples. This reflects the high level of similarity in the molecular composition of these two closely related SOA materials. Several highly conjugated products were detected exclusively in the brown LSOA sample and were identified as potential chromophores responsible for the observed color change. The majority of the unique products in the aged LSOA sample with the highest number of double bonds contain two nitrogen atoms. We conclude that chromophores characteristic of the carbonyl-imine chemistry in LSOA are highly conjugated oligomers of secondary imines (Schiff bases) present at relatively low concentrations. Formation of this type of conjugated compounds in PSOA is hindered by the structural rigidity of the α-pinene oxidation products. Our results suggest that the overall light-absorbing properties of SOA may be determined by trace amounts of strong brown carbon chromophores.

Effect of solar radiation on the optical properties and molecular composition of laboratory proxies of atmospheric brown carbon

Sources, optical properties, and chemical composition of atmospheric brown carbon (BrC) aerosol are uncertain, making it challenging to estimate its contribution to radiative forcing. Furthermore, optical properties of BrC may change significantly during its atmospheric aging. We examined the effect of photolysis on the molecular composition, mass absorption coefficient, and fluorescence of secondary organic aerosol (SOA) prepared by high-NOx photooxidation of naphthalene (NAP SOA). Our experiments were designed to model photolysis processes of NAP SOA compounds dissolved in cloud or fog droplets. Aqueous solutions of NAP SOA were observed to photobleach (i.e., lose their ability to absorb visible radiation) with an effective half-life of ∼15 h (with sun in its zenith) for the loss of near-UV (300-400 nm) absorbance. The molecular composition of NAP SOA was significantly modified by photolysis, with the average SOA formula changing from C14.1H14.5O5.1N0.085 to C11.8H14.9O4.5N0.023 after 4 h of irradiation. However, the average O/C ratio did not change significantly, suggesting that it is not a good metric for assessing the extent of photolysis-driven aging in NAP SOA (and in BrC in general). In contrast to NAP SOA, the photobleaching of BrC material produced by the reaction of limonene + ozone SOA with ammonia vapor (aged LIM/O3 SOA) was much faster, but it did not result in a significant change in average molecular composition. The characteristic absorbance of the aged LIM/O3 SOA in the 450-600 nm range decayed with an effective half-life of <0.5 h. These results emphasize the highly variable and dynamic nature of different types of atmospheric BrC.