Mechanical power driven SPME-SERS ultra-fast detection of illegal additives in aquaculture water

A dual-function (extraction and detection) porous silver fiber with high enhancement effect was constructed based on a convenient electrochemical etching method. The prepared silver fiber not only had high enrichment capacity and good Surface Enhanced Raman Spectroscopy (SERS) performance but also had good laser stability and uniformity. A strategy combining mechanical power and integration of solid phase extraction (SPME) and SERS detection was used. Driven by mechanical power, the analyte malachite green (MG) was enriched on the prepared silver fiber after 40 seconds, which can realize an ultra-fast and sensitive detection with a detection limit of 8.48 × 10-9 M. At the same time, this fiber can be regenerated after being treated with NaBH4. The silver fiber can be used for the detection of MG and CV after being immersed in NaBH4 solution for a few minutes. After 5 cycles of processing, the measurement signals of the silver fiber can reach 70% of the initial signals. The mechanical power driven SPME-SERS (MPD-SPME-SERS) integrated detection method can be used to analyse aquaculture water within 1 minute with a good linear relationship.

SERS-Based Molecularly Imprinted Plasmonic Sensor for Highly Sensitive PAH Detection

A novel hybrid plasmonic platform based on the synergetic combination of a molecularly imprinted polymer (MIP) thin film with Au nanoparticle (NPs) assemblies, noted as Au@MIP, was developed for surface-enhanced Raman scattering (SERS) spectroscopy recognition of polycyclic aromatic hydrocarbons (PAHs). While the MIP trapped the PAH close to the Au surface, the plasmonic NPs enhanced the molecule's Raman signal. The Au@MIP fabrication comprises a two-step procedure, first, the layer-by-layer deposition of Au NPs on glass and their further coating with a uniform MIP thin film. Profilometry analysis demonstrated that the thickness and homogeneity of the MIP film could be finely tailored by tuning different parameters such as prepolymerization time or spin-coating rate. Two different PAH molecules, pyrene or fluoranthene, were used as templates for the fabrication of pyrene- or fluoranthene-based Au@MIP substrates. The use of pyrene or fluoranthene, as the template molecule to fabricate the Au@MIP thin films, enabled its ultradetection in the nM regime with a 100-fold improvement compared with the nonimprinted plasmonic sensors (Au@NIPs). The SERS data analysis allowed to estimate the binding constant of the template molecule to the MIP. The selectivity of both pyrene- and fluoranthene-based Au@MIPs was analyzed against three PAHs of different sizes. The results displayed the important role of the template molecule used for the Au@MIPs fabrication in the selectivity of the system. Finally, the practical applicability of pyrene-based Au@MIPs was shown by performing the detection of pyrene in two real samples: creek water and seawater. The design and optimization of this type of plasmonic platform will pave the way for the detection of other relevant (bio)molecules in a broad range of fields such as environmental control, food safety, or biomedicine.

A Review of Chinese Raman Spectroscopy Research Over the Past Twenty Years

This paper introduces the major Chinese research groups in the fields of biomedicine, food safety, environmental testing, material research, archaeological and cultural relics, gem identification, forensic science, and other research areas of Raman spectroscopy and combined methods spanning the two decades from 1997 to 2017. Briefly summarized are the research directions and contents of the major Chinese Raman spectroscopy research groups, giving researchers engaged in Raman spectroscopy research a more comprehensive understanding of the state of Chinese Raman spectroscopy research and future development trends to further develop Raman spectroscopy and its applications.

Combining microextraction methods with surface-enhanced Raman spectroscopy towards more selective and sensitive analyte detection by plasmonic metal nanoparticles

Raman signals of analytes can be enhanced on the surface of noble nanoparticles by generating SERS signals, which can be further enhanced using microextraction (ME) techniques.

Solid-phase microextraction: An appealing alternative for the determination of endogenous substances - A review

The determination of endogenous substances is of great significance for obtaining important biotic information such as biological components, metabolic pathways and disease biomarkers in different living organisms (e.g. plants, insects, animals and humans). However, due to the complex matrix and the trace concentrations of target analytes, the sample preparation procedure is an essential step before the analytes of interest are introduced into a detection instrument. Solid-phase microextraction (SPME), an emerging sample preparation technique that integrates sampling, extraction, concentration, and sample introduction into one step, has gained wide acceptance in various research fields, including in the determination of endogenous compounds. In this review, recent developments and applications of SPME for the determination of endogenous substances over the past five years are summarized. Several aspects, including the design of SPME devices (sampling configuration and coating), applications (in vitro and in vivo sampling), and coupling with emerging instruments (comprehensive two-dimensional gas chromatography (GC × GC), ambient mass spectrometry (AMS) and surface enhanced Raman scattering (SERS)) are involved. Finally, the challenges and opportunities of SPME methods in endogenous substances analysis are also discussed.

Braid solid-phase microextraction of polycyclic aromatic hydrocarbons by using fibers coated with silver-based nanomaterials in combination with HPLC with fluorometric detection

Authors propose a novel braid support configuration for use in solid-phase microextraction (SPME) fibers. Two different braided supports (double and triple) were prepared and compared with the conventional single support configuration. Three kinds of silver-based nanomaterials that serve as coatings on these supports are described. They included silver dendrites, silver nanoparticles (AgNPs), and silver dendrites decorated with AgNPs (Ag-dendrites@AgNPs). They were prepared by electrodeposition, a layer-by-layer (LBL) method, and a hybrid strategy, respectively. Fibers were used in the direct-immersion (DI) mode of SPME. Five polycyclic aromatic hydrocarbons (PAHs) were studied as model analytes by DI-SPME when analyzing (spiked) underground waters. PAHs were further determined with high-performance liquid chromatography (HPLC) and fluorescence detection. The analytical performance of the fibers was compared to that of the commercial polydimethylsiloxane (PDMS) fiber of 100 μm thickness. AgNPs obtained by LBL was the best coating and the double braid was the best support configuration. The configuration of the SPME support always played an important role independently on the coating material, being always beneficial the use of double-braids. Despite the low coatings volumes of the silver-based fibers compared to that of PDMS, the analytical features of the method were adequate. Figures of merit include: (a) limits of detection down to 20 ng·L^-1; (b) intra-day, inter-day, and inter-fiber precisions (expressed as RSDs) of <13%, <12%, and < 13%, respectively; and (c) adequate operational lifetime (>60 extractions). Graphical abstract Schematic presentation of braided solid-phase microextraction support configurations together with different silver-based nanomaterials as coatings.

Miniaturized array gas membrane separation strategy for rapid analysis of complex samples by surface-enhanced Raman scattering

It remains a significant challenge for fast and high-throughput detection of trace analytes in complex samples with surface-enhanced Raman scattering (SERS) strategy due to the severe interference from matrices. In this work, a miniaturized array gas membrane separation (AGMS) device coupled with SERS was designed and drew up to eliminate matrix influence and improve the reproducibility of SERS signal during real sample analysis. The design of miniaturized AGMS tube was optimized based on quantitative calculation of its air permeability by computational fluid dynamics simulation. A 10 mm height tube was selected as an optimized design with a recovery of 98.3% for acetaldehyde. The practical feasibility of miniaturized AGMS was validated based on the applications in biochemical analysis and food analysis, such as albuminuria and acetaldehyde in urine sample and metaldehyde and thiram in food samples. The results showed that SERS responses of all analytes dramatically increased by eliminating sample matrices after miniaturized AGMS process. Acetaldehyde, albuminuria, metaldehyde and thiram in real samples could be accurately quantified with recoveries of 82.0-123.3%, and the analytical results were validated by corresponding standard methods with relative error ranging from -4.8% to 5.3%. Time consumption of miniaturized AGMS-SERS for one real sample analysis including sample preparation and determination was less than 20 min and could treat 96 samples with 45 min in one run. It is potential that the miniaturized AGMS technique automated by implementation with a robotic arm could greatly expand the range and accelerate the speed of SERS analysis.

Three-dimensional Pd/Pt bimetallic nanodendrites on a highly porous copper foam fiber for headspace solid-phase microextraction of BTEX prior to their quantification by GC-FID

The preparation of bimetallic Pd/Pt nanofoam for use in fiber based solid-phase microextraction (SPME) is described. First, a highly porous copper foam was prepared on the surface of an unbreakable copper wire by an electrochemical method. Then, the substrate was covered with metallic Pd and Pt using galvanic replacement of the Cu nanofoam substrate by applying a mixture of Pd(II) and Pt(IV) ions. The procedure provided an efficient route to modify Pd/Pt nanofoams with large specific surface and low loading with expensive noble metals. The fiber was applied to headspace SPME of benzene, toluene, ethylbenzene and xylene (BTEX) (as the model compounds) in various spiked water and wastewater samples. It was followed by gas chromatography-flame ionization detection (GC-FID). A Plackett-Burman design was performed for screening the experimental factors prior to Box-Behnken design. Compared with the commercial PDMS SPME fiber (100 μm), it had higher extraction efficiency for BTEX. Under the optimum conditions, the method has low limits of detection (0.16-0.35 μg L^-1), a wide linear range (1-200 μg L^-1), relative standard deviations between 5.8 and 10.5%, and good recoveries (>85% from spiked samples). Graphical abstract Schematic presentation of a three-dimensional Pd/Pt bimetallic nanodendrites supported on a highly porous copper foam fiber for use in headspace solid phase microextraction of BTEX. They were then quantified by gas chromatography-flame ionization detector.

Combining Headspace Solid-Phase Microextraction and Surface-Enhanced Raman Spectroscopy To Detect the Pesticide Fonofos in Apple Juice

We developed an innovative approach that couples headspace solid-phase microextraction (SPME) with surface-enhanced Raman spectroscopy (SERS) to detect a volatile pesticide (i.e., fonofos) in a liquid complex matrix (i.e., apple juice). A gold nanoparticles-coated fiber was fabricated by reducing gold(III) on a chemically etched stainless steel wire to extract pesticide, using SPME. The fabricated fibers were then tested by a headspace-SPME method and a dip-SPME method, followed by SERS detection of fonofos in water and apple juice samples. Using the headspace-SPME method, we can detect as low as 5 ppb of fonofos in water and apple juice, compared with the dip-SPME method, which cannot detect lower than 10 ppb in water and 50 ppb in apple juice. This study demonstrated the potential capability of the headspace-SPME-SERS method for rapid (within 30 min) and sensitive detection of volatile and vaporizable compounds in complex matrices. The developed method could be a potential alternative approach to the gas chromatography method. Future work is needed to optimize the fiber by minimizing signal variation, and it should be tested in a variety of targeted compounds and matrices.

Silver nanoparticles supported onto a stainless steel wire for direct-immersion solid-phase microextraction of polycyclic aromatic hydrocarbons prior to their determination by GC-FID

The authors describe a new coating for use in solid-phase microextraction (SPME). Silver nanoparticles (AgNPs) were prepared by using gallic acid or glucose as the reducing agents, and then supported onto a stainless steel wire that was previously coated with a silver mirror. Coating with AgNPs was performed by a layer-by-layer approach of up to eight cycles of consecutive deposition of AgNPs and the thiol linker 1,8-octanedithiol. This procedure allows proper control of the coating thickness. Thicknesses are 3.2 μm and 3.5 μm with AgNPs obtained with gallic acid and glucose, respectively. This is in agreement with theoretical estimations (3.8 μm). The fibers were used in the direct-immersion SPME-GC-FID determination of 16 polycyclic aromatic hydrocarbons (PAHs) from different waters. The performance of the method was compared to the one using polydimethylsiloxane fibers (100 μm), which is the most suitable commercial SPME fiber for PAHs. Despite the low thickness of the AgNP coatings (compared to PDMS), the analytical features of the method using the most adequate coating (AgNPs prepared with gallic acid) include: (a) limits of detection down to 0.6 ng·mL^-1; (b) intra-day, inter-day, and inter-fiber precisions (expressed as RSDs) lower than 22, 26 and 25%, respectively; and (c) an operational lifetime of ~150 extractions/desorption cycles. The analysis of various spiked environmental waters using these fibers resulted in adequate analytical performance. Graphical abstract Silver nanoparticle based coatings for solid-phase microextraction fibers were prepared by a layer-by-layer approach. They were used for determination of 16 PAHs in waters by gas chromatography. Limits of detection are < 14 μg·L^-1 and intra-day, inter-day, and inter-fiber precisions are <26%.

Combination of a graphene SERS substrate and magnetic solid phase micro-extraction used for the rapid detection of trace illegal additives

Surface enhanced Raman scattering (SERS) is an ultra-sensitive spectroscopy technique, which can provide rich structural information for a great number of molecules, while solid phase micro-extraction (SPME) is an efficient method for sample pretreatment in analytical chemistry, particularly in a micro-system.

Au@Ag core–shell nanoparticles with a hidden internal reference promoted quantitative solid phase microextraction-surface enhanced Raman spectroscopy detection

Structural representation of the SPME-SERS fiber with an internal reference and the SERS detection.

Porous silver coating fiber for rapidly screening organotin compounds by solid phase microextraction coupled with surface enhanced Raman spectroscopy

Rapidly screening organotin by solid phase microextraction coupled with surface enhanced Raman spectroscopy.

In situ dispersion of oil-based Ag nanocolloids by microdroplet coalescence and their applications in SERS detection

Monodispersity and size uniformity of the nanoparticles coated on film-like nanosensors are critical for detection efficiency.

Pollutant capturing SERS substrate: porous boron nitride microfibers with uniform silver nanoparticle decoration

How to concentrate target molecules on the surface of a SERS substrate is a key problem in the practical application of SERS. Herein, we designed for the first time a pollutant capturing surface enhanced Raman spectroscopy (SERS) substrate, namely porous BN microfibers uniformly decorated with Ag nanoparticles, in which the BN microfibers adsorb pollutants, while the Ag nanoparticles provide SERS activity. This SERS substrate captures pollutants from an aqueous solution completely and accumulates them all on its surface without introducing noise signals. The pores of BN protect the silver particles from aggregation which makes BN/Ag a stable and recyclable SERS substrate. What's more, while the dyes are thoroughly concentrated from a diluted solution, the SERS detection limit is easily enhanced, from 10(-6) M to 10(-9) M.