Enhanced photocatalytic performances of n-TiO₂ nanotubes by uniform creation of p-n heterojunctions with p-Bi₂O₃ quantum dots

Electrostatic Repulsive Features of Free-Standing Titanium Dioxide Nanotube-Based Membranes in Biofiltration Applications

This study presents the electrostatic repulsive features of electrochemically fabricated titanium dioxide nanotube (NT)-based membranes with different surface nanomorphologies in cross-flow biofiltration applications while maintaining a creatinine clearance above 90%. Although membranes exhibit antifouling behavior, their blood protein rejection can still be improved. Due to the electrostatically negative charge of the hexafluorotitanate moiety, the fabricated biocompatible, superhydrophilic, free-standing, and amorphous ceramic nanomembranes showed that about 20% of negatively charged 66 kDa blood albumin was rejected by the membrane with ∼100 nm pores. As the nanomorphology of the membrane was shifted from NTs to nanowires by varying fabrication parameters, pure water flux and bovine serum albumin (BSA) rejection performance were reduced, and the membrane did not lose its antifouling behavior. Herein, nanomembranes with different surface nanomorphologies were fabricated by a multi-step anodic oxidation process and characterized by scanning electron microscopy, atomic force microscopy, water contact angle analysis, X-ray diffraction, and energy-dispersive X-ray spectroscopy. The membrane performance of samples was measured in 3D printed polyethylene terephthalate glycol flow cells replicating implantable artificial kidney models to determine their blood toxin removal and protein loss features. In collected urine mimicking samples, creatinine clearances and BSA rejections were measured by the spectrophotometric Jaffe method and high-performance liquid chromatography.

One-Step Hydrothermal Synthesis of Anatase TiO2 Nanotubes for Efficient Photocatalytic CO2 Reduction

The hydrothermal dissolution-recrystallization process is a key step in the crystal structure of titania-based nanotubes and their composition. This work systematically studies the hydrothermal conditions for directly synthesizing anatase TiO₂ nanotubes (ATNTs), which have not been deeply discussed elsewhere. It has been well-known that ATNTs can be synthesized by the calcination of titanate nanotubes. Herein, we found the ATNTs can be directly synthesized by optimizing the reaction temperature and time rather than calcination of titanate nanotubes, where at each temperature, there is a range of reaction times in which ATNTs can be prepared. The effect of NaOH/TiO₂ ratio and starting materials was explored, and it was found that ATNTs can be prepared only if the precursor is anatase TiO₂, using rutile TiO₂ leads to forming titanate nanotubes. As a result, ATNTs produced directly without calcination have excellent photocatalytic CO₂ reduction than titanate nanotubes and ATNTs prepared by titanate calcination.

Sputtering-Assisted Synthesis of Copper Oxide–Titanium Oxide Nanorods and Their Photoactive Performances

A TiO₂ nanorod template was successfully decorated with a copper oxide layer with various crystallographic phases using sputtering and postannealing procedures. The crystallographic phase of the layer attached to the TiO₂ was adjusted from a single Cu₂O phase or dual Cu₂O–CuO phase to a single CuO phase by changing the postannealing temperature from 200 °C to 400 °C. The decoration of the TiO₂ (TC) with a copper oxide layer improved the light absorption and photoinduced charge separation abilities. These factors resulted in the composite nanorods demonstrating enhanced photoactivity compared to that of the pristine TiO₂. The ternary phase composition of TC350 allowed it to achieve superior photoactive performance compared to the other composite nanorods. The possible Z-scheme carrier movement mechanism and the larger granular size of the attached layer of TC350 under irradiation accounted for the superior photocatalytic activity in the degradation of RhB dyes.

Selective Photoelectrocatalytic Glycerol Oxidation to Dihydroxyacetone via Enhanced Middle Hydroxyl Adsorption over a Bi2O3-Incorporated Catalyst

Photoelectrocatalytic (PEC) glycerol oxidation offers a sustainable approach to produce dihydroxyacetone (DHA) as a valuable chemical, which can find use in cosmetic, pharmaceutical industries, etc. However, it still suffers from the low selectivity (≤60%) that substantially limits the application. Here, we report the PEC oxidation of glycerol to DHA with a selectivity of 75.4% over a heterogeneous photoanode of Bi₂O₃ nanoparticles on TiO₂ nanorod arrays (Bi₂O₃/TiO₂). The selectivity of DHA can be maintained at ∼65% under a relatively high conversion of glycerol (∼50%). The existing p-n junction between Bi₂O₃ and TiO₂ promotes charge transfer and thus guarantees high photocurrent density. Experimental combined with theoretical studies reveal that Bi₂O₃ prefers to interact with the middle hydroxyl of glycerol that facilitates the selective oxidation of glycerol to DHA. Comprehensive reaction mechanism studies suggest that the reaction follows two parallel pathways, including electrophilic OH* (major) and lattice oxygen (minor) oxidations. Finally, we designed a self-powered PEC system, achieving a DHA productivity of 1.04 mg cm^-2 h^-1 with >70% selectivity and a H₂ productivity of 0.32 mL cm^-2 h^-1. This work may shed light on the potential of PEC strategy for biomass valorization toward value-added products via PEC anode surface engineering.

Stepwise assembly and reversible structural transformation of ligated titanium coated bismuth-oxo cores: shell morphology engineering for enhanced chemical fixation of CO2

Herein, we report the stepwise assembly and reversible transformation of atomically precise ligated titanium coated bismuth-oxide core nanostructures. The soluble and stable Bi38O45@Ti6-oxo clusters with weakly coordinated surface salicylate ligands were first prepared as precursors. Owing to the high surface reactivity of the Bi38O45 inner core, its shell composition and morphology could be systemically modified by assembly with various Ti ions and auxiliary ligands (L), especially those with different flexibility, bridging ability and steric hindrance. As a result, a series of new core-shell Bi38O44/45@Ti x L-oxo (x = 14, 16, 18 or 20) clusters containing gradually increasing shell Ti atoms were successfully synthesized. Among them, the Bi38Ti20-oxo cluster is the largest one in the family of heterometallic Bi/Ti-oxo clusters to date. In addition, the sensitized titanium outer shell can effectively improve the photocurrent response under visible light irradiation. More remarkably, the obtained core-shell Bi38O44/45@Ti x L-oxo clusters can serve as stable and efficient catalysts for CO2 cycloaddition with epoxides under ambient conditions, whose activity was significantly influenced by the outer ligated titanium shell structure. This work provides a new insight into the construction of atomically precise heterometallic core-shell nanostructures and also an interesting shell engineering strategy for tuning their physicochemical properties.

Oxygen Vacancy-Enhanced Ultrathin Bi2O3-Bi2WO6 Nanosheets' Photocatalytic Performances under Visible Light Irradiation

The oxygen vacancy caused by ultrathin structures would be introduced into the semiconductor photocatalyst to boost its photocatalytic activity. Herein, ultrathin Bi₂O₃-Bi₂WO₆ nanosheet composites have been successfully synthesized via a facile hydrothermal method. Compared to pure Bi₂WO₆ nanosheets, the Bi₂O₃-Bi₂WO₆ nanosheet composites possess abundant oxygen vacancies, which was confirmed by the positron annihilation spectra. The ultrathin Bi₂O₃-Bi₂WO₆ nanosheet composites exhibited remarkable photocatalytic degradation performance for oxytetracycline compared with that of pure Bi₂WO₆ nanosheets. The excellent photocatalytic activities of Bi₂O₃-Bi₂WO₆ composites could be attributed to the heterojunction structure and the oxygen vacancies caused by ultrathin structures.

Bi2O3-Sensitized TiO2 Hollow Photocatalyst Drives the Efficient Removal of Tetracyclines under Visible Light

The complete removal of tetracycline residuals under visible light still is a challenging task because of their robust ring structure. To tackle this issue, we explore a novel Bi₂O₃-sensitized TiO₂ visible-light photocatalyst by combining p-n heterojunction with hollow structure. The hollow TiO₂/Bi₂O₃ photocatalyst manifests excellent photocatalytic performance and recyclability toward the complete degradation (100%) of antibiotics under visible light (λ > 420 nm) because of the synergistic effect of p-n heterojunction and hollow structure, successfully overcoming the challenge of the incomplete removal of antibiotics over almost all of the reported visible-light photocatalysts. Additionally, the effects of inorganic ions, pH value, water matrix, and outdoor light on the degradation of tetracyclines were investigated with many details. Notably, the degradation pathways and mechanism of tetracycline were revealed according to trapping experiments, HPLC-MS, and photoelectrochemical characterizations. Therefore, this work provides a new insight into developing visible-light photocatalysts with excellent photocatalytic performances for the complete removal of other refractory contaminants.

One-Pot Synthesis of Anatase, Rutile-Decorated Hydrogen Titanate Nanorods by Yttrium Doping for Solar H2 Production

We have prepared yttrium (Y)-doped hydrogen titanate nanorods (HTN) by a microwave-assisted hydrothermal method. Y-doped HTN showed much improved photocatalytic activities for both H₂ evolution and dye decomposition. H₂ production from a methanol-water solution under UV-visible light for 7 h was enhanced by a factor of 5.5 with 1 wt % Y-doping. Doping with Y³⁺ ions reduced the band gap of HTN by ∼0.28 eV and induced new phases of anatase and rutile. High photocatalysis by Y-doping was attributed to enhanced light absorption (smaller band gap) and effective charge separation (heterojunction). To optimize H₂ production, a series of experiments examining effects of doping concentrations and non-noble surface metal (e.g., Ni, Cu, Co) loading were carefully performed. Y-doping in this work is a new and promising approach for synthesizing highly active HTN by producing the HTN/rutile/anatase heterostructure within the one-pot method.

Coverage Layer Phase Composition-Dependent Photoactivity of One-Dimensional TiO2-Bi2O3 Composites

TiO₂–Bi₂O₃ composite rods were synthesized by combining hydrothermal growth of rutile TiO₂ rod templates and sputtering deposition of Bi₂O₃ thin films. The TiO₂–Bi₂O₃ composite rods with β-Bi₂O₃ phase and α/β-Bi₂O₃ dual-phase decoration layers were designed, respectively, via in situ radio-frequency magnetron sputtering growth and post-annealing procedures in ambient air. The crystal structure, surface morphology, and photo-absorption performances of the pristine TiO₂ rods decorated with various Bi₂O₃ phases were investigated. The crystal structure analysis reveals that the crystalline TiO₂–Bi₂O₃ rods contained β-Bi₂O₃ and α/β-Bi₂O₃ crystallites were separately formed on the TiO₂ rod templates with different synthesis approaches. The morphology analysis demonstrates that the β-Bi₂O₃ coverage layer on the crystalline rutile TiO₂ rods showed flat layer morphology; however, the surface morphology of the α/β-Bi₂O₃ dual-phase coverage layer on the TiO₂ rods exhibited a sheet-like feature. The results of photocatalytic decomposition towards methyl orange dyes show that the substantially improved photoactivity of the rutile TiO₂ rods was achieved by decorating a thin sheet-like α/β-Bi₂O₃ coverage layer. The effectively photoinduced charge separation efficiency in the stepped energy band configuration in the composite rods made from the TiO₂ and α/β-Bi₂O₃ explained their markedly improved photoactivity. The TiO₂-α/β-Bi₂O₃ composite rods are promising for use as photocatalysts and photoelectrodes.

An all-in-one strategy for the adsorption of heavy metal ions and photodegradation of organic pollutants using steel slag-derived calcium silicate hydrate

Low-cost and high-performance materials or techniques that could synergistically remove inorganic heavy metals and organic pollutants in a simple manner are highly desired. Herein, we report a simple and facile strategy by converting poisonous heavy metals into photocatalyst for the in-situ photodegradation of organic pollutants employing steel slag-derived calcium silicate hydrate (CSH). The CSH was synthesized by alkali activation method and showed hierarchical structure and amorphous phase. And, the material exhibited excellent adsorption performance towards all selected heavy metals. After adsorption, the heavy metals were converted into the corresponding amorphous metal hydroxides on the surface of CSH. The resulting CSH-supported amorphous metal hydroxides can act as visible-light photocatalysts for the photodegradation of organic pollutants. The optimal results for the whole water purification route using CSH are > 100 mg/g adsorption capacity for Cu²⁺ and ˜63% / 8 h photodegradation efficiency for methylene blue under visible light. The total cost for the whole route is < 0.1 $/g pollutants, much lower than traditional technologies. The strategy using steel slag derived-CSH not only meets the requirements for high-performance and low-cost materials, but also resolves the challenging issues of developing an all-in-one treatment for heavy metal ions and organic pollutants, which will be of great significance to wastewater purification.

Bi2O3 and g-C3N4 quantum dot modified anatase TiO2 heterojunction system for degradation of dyes under sunlight irradiation

A facile and feasible method was successfully utilized to incorporate Bi₂O₃ and g-C₃N₄ quantum dots on TiO₂ surface to synthesize a novel composite g-C₃N₄/TiO₂/Bi₂O₃. The photocatalytic activity of the composite g-C₃N₄/TiO₂/Bi₂O₃ for degradation of dyes under sunlight and UV light irradiation was evaluated. It possessed the higher photocatalytic performance than that of pristine TiO₂ or g-C₃N₄ under the same conditions. Under sunlight irradiation, the reaction rate constants of the g-C₃N₄/TiO₂/Bi₂O₃ was about 4.2 times and 3.3 times higher than that of TiO₂ and g-C₃N₄, respectively. The promising photocatalytic performance was attributed to the broader light absorption range and efficient separation of photoinduced carriers. Moreover, based on the TEM, XPS, XRD, UV-vis spectrum, radicals scavenging test and Mott–Schottky analysis systematic mechanism for photodegradation process was proposed. This work provides a promising strategy for the modification of TiO₂-based semiconductors by incorporating different quantum dots and promoting the efficiency of the photocatalysts in practical application.

A facile and feasible method was successfully utilized to incorporate Bi₂O₃ and g-C₃N₄ quantum dots on TiO₂ surface to synthesize a novel composite g-C₃N₄/TiO₂/Bi₂O₃.

Reusability and photocatalytic activity of bismuth-TiO2 nanocomposites for industrial wastewater treatment

In this study, bismuth-TiO₂ nanotube (Bi-TNT) composites were used for the treatment of industrial wastewater. Bi-TNT were synthesized using two- and one-step anodization methods. The obtained composites were analyzed using X-ray diffraction, field emission scanning electron microscopy, UV-visible diffuse reflectance spectroscopy, Energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. For the two-step Bi-TNT composites, we investigated the effect of different Bi deposition times, Bi concentrations, and Bi deposition voltages on photodegradation efficiency. For the one-step Bi-TNT composites, we investigated the effect of different anodization voltages, anodization times, and Bi concentrations. Initially, the optimal synthesis conditions for two- and one-step Bi-TNT catalysts were identified and then these optimized conditions were used for industrial wastewater treatment that was collected from Banwol Sihwa Industrial Complex Republic of Korea. The Bi-TNT two- and one-step composites showed 2.0 and 2.5 times higher photocatalytic activity, respectively, for industrial wastewater treatment than that of TNT in visible-light. Recycling of Bi-TNT composites showed that the one-step composite method was more efficient and stable than the two-step method because Bi coupling and nanotube formation simultaneously occurred.

Construction of noble-metal-free TiO2 nanobelt/ZnIn2S4 nanosheet heterojunction nanocomposite for highly efficient photocatalytic hydrogen evolution

A binary nanocomposite composed of two-dimensional (2D) ultrathin ZnIn₂S₄ nanosheets and one-dimension (1D) TiO₂ nanobelts was prepared and applied as a noble-metal-free photocatalyst for hydrogen evolution under solar-light irradiation. The TiO₂ nanobelt/ZnIn₂S₄ nanosheet heterojunction nanocomposites show higher light absorption capacity, larger surface area and higher separation of charge carriers in comparison to pristine TiO₂ and ZnIn₂S₄. As a result, the hydrogen production over the TiO₂/ZnIn₂S₄ nanocomposite with 15 wt% TiO₂ can reach up to 348.21 μmol · g^-1 · h^-1, even without noble metals, which is about 26 and 2.3 times higher than the pristine TiO₂ and ZnIn₂S₄, respectively. Meanwhile, a possible photocatalytic mechanism of TiO₂/ZnIn₂S₄ heterojunction nanocomposites was proposed and corroborated by photoluminescence (PL) spectroscopy and photoelectrochemical (PEC) results. This work paves a way for developing low-cost and high-efficiency noble-metal-free photocatalytic systems for solar-to-hydrogen evolution.

How does the Zn-precursor nature impact carrier transfer in ZnO/Zn-TiO2 nanostructures? organic vs. inorganic anions

The carrier transport capability of ZnO/Zn-TiO₂ nanostructures is affected by Zn-precursor anions, generating donor, acceptor and interfacial energy states.

Visible-light-assisted photocatalytic activity of bismuth-TiO2 nanotube composites for chromium reduction and dye degradation

TiO₂ nanotubes (TNTs) were synthesized on a Ti sheet using the electrochemical anodization method. Bismuth (Bi) was coupled on the anodized TNTs via hydrothermal process. We verified the effect of different Bi concentrations on the photocatalytic properties of Bi-TNT composites. The obtained samples were characterized using field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, UV-Vis diffuse reflectance spectra, and photoluminescence spectra. The Bi-TNT photocatalysts exhibited higher activities by factors of 6.6 and 3.6 toward chromium reduction and methylene blue degradation, respectively, under visible light than the pure TNTs. The Bi-TNT material was recycled to examine the stability of the catalyst. The quantum efficiency of the photocatalytic system was calculated, and the synergistic effects of bismuth modification were discussed. The Bi-TNT composites were observed to be promising for separation of photoinduced e^- and h⁺ by decreasing charge recombination, and helped the formation of the hydroxyl radicals, h⁺, and superoxides used in the photocatalytic process.

A Facile Method for Preparation of Cu2O-TiO2 NTA Heterojunction with Visible-Photocatalytic Activity

Based on highly ordered TiO2 nanotube arrays (NTAs), we successfully fabricated the Cu2O-TiO2 NTA heterojunction by a simple thermal decomposition process for the first time. The anodic TiO2 NTAs were functioned as both "nano-container" and "nano-reactors" to load and synthesize the narrow band Cu2O nanoparticles. The loaded Cu2O expanded absorption spectrum of the TiO2 NTAs from ultraviolent range to visible light range. We found that the Cu2O-TiO2 NTA heterojunction films had visible activity towards photocatalytic degrading methyl orange (MO). The photocatalytic abilities of the Cu2O-TiO2 NTA heterojunction films were found increased with the Cu2O content from 0.05 to 0.3 mol/L. This could be explained by more electron-hole pairs generated and less recombination, when the Cu2O-TiO2 heterojunction got formed. Here, we put forward this promising method, hoping it can facilitate the mass production and applications of Cu2O-TiO2 NTA heterojunction.

Quantum dot-decorated semiconductor micro- and nanoparticles: A review of their synthesis, characterization and application in photocatalysis

Quantum dot (QD)-decorated semiconductor micro- and nanoparticles are a new class of functional nanomaterials that have attracted considerable interest for their unique structural, optical and electronic properties that result from the large surface-to-volume ratio and the quantum confinement effect. In addition, because of QDs' excellent light-harvesting capacity, unique photoinduced electron transfer, and up-conversion behaviour, semiconductor nanoparticles decorated with quantum dots have been used widely in photocatalytic applications for the degradation of organic pollutants in both the gas and aqueous phases. This review is a comprehensive overview of the recent progress in synthesis methods for quantum dots and quantum dot-decorated semiconductor composites with an emphasis on their composition, morphology and optical behaviour. Furthermore, various approaches used for the preparation of QD-based composites are discussed in detail with respect to visible and UV light-induced photoactivity. Finally, an outlook on future development is proposed with the goal of overcoming challenges and stimulating further research into this promising field.

High-efficiency SrTiO3/TiO2 hetero-photoanode for visible-light water splitting by charge transport design and optical absorption management

Herein, a two-pronged approach to obtain excellent visible-light performance of SrTiO₃/TiO₂ photoelectrodes for water oxidation is presented. More specifically, the combination of hetero-constructing SrTiO₃ nanocubes and Cr³⁺/Ti³⁺ dual-doping has been demonstrated for achieving high efficiency of charge separation and extending photoresponse of TiO₂ nanotube arrays from the UV to visible light region. As expected, this unique Cr-SrTiO_3-x/Cr-TiO_2-x photoanode exhibited remarkably improved PEC performance for water splitting (4.05 mA cm^-2) under visible light irradiation, which is more than 100 times higher than that of pristine TiO₂ nanotube arrays. Additionally, the photocurrent intensity as well as water splitting behavior remain constant even after long time irradiation, revealing its high PEC as well as structure stability. Thereby, the rational design of the interface charge transport and precise management of optical absorption endow the TiO₂-based PEC system with excellent and stable visible-light performance for water splitting.

Sequential ionic layer adsorption and reaction (SILAR) deposition of Bi4Ti3O12 on TiO2: an enhanced and stable photocatalytic system for water purification

A new method to produce bismuth titanate – titanium dioxide composites by modification of a TiO₂ film deposited on a variety of different glass substrates is reported.

Uniform carbon dots@TiO2 nanotube arrays with full spectrum wavelength light activation for efficient dye degradation and overall water splitting

This work presents a novel approach for preparing photocatalysts based on TiO₂ nanotube arrays (TiO₂ NTAs) anchored with carbon dots (CDs) by a facile two-step method which includes an electrochemical anodization technique followed by electrochemical deposition. The synthesized high quality graphitic carbon dots can act as sensitizers to extend the spectral range of light absorption towards the full solar spectrum. It is confirmed that TiO₂ NTAs anchored with CDs (CDs/TiO₂ NTAs) display greatly improved photocatalytic activity and excellent photocatalytic stability. By tuning the light absorption of the TiO₂ NTAs, the utilization of light in charge generation and separation is well synergized with the CDs for enhanced photocatalytic pollutant degradation and water splitting, achieving significantly improved rates of photocatalytic degradation and H₂ production in the visible and full spectra, respectively.

Shape-Controlled Metal-Free Catalysts: Facet-Sensitive Catalytic Activity Induced by the Arrangement Pattern of Noncovalent Supramolecular Chains

Metal-free catalytic materials have recently received broad attention as promising alternatives to metal-involved catalysts. This is owing to their inherent capability to overcome the inevitable limitations of metal-involved catalysts, such as high sensitivity to poisoning, the limited reserves, high cost and scarcity of metals (especially noble metals), etc. However, the lack of shape-controlled metal-free catalysts with well-defined facets is a formidable bottleneck limiting our understandings on the underlying structure-activity relationship at atomic/molecular level, which thereby restrains their rational design. Here, we report that catalytically active crystals of a porphyrin, 5,10,15,20-tetrakis(pentafluorophenyl)porphyrin, could be shaped into well-defined cubes and sheet-like tetradecahedrons (TDHD), which are exclusively and predominantly enclosed by {101} and {001} facets, respectively. Fascinatingly, compared to the cubes, the TDHDs display substantially enhanced catalytic activity toward water decontamination under visible-light irradiation, although both the architectures have identical crystalline structure. We disclose that such interesting shape-sensitive catalytic activity is ascribed to the distinct spatial separation efficiency of photogenerated electrons and holes induced by single-channel and multichannel charge transport pathways along noncovalent supramolecular chains, which are arranged as parallel-aligned and 2D network patterns, respectively. Our findings provide an ideal scientific platform to guide the rational design of next-generation metal-free catalysts of desired catalytic performances.

Understanding the Role of Dynamic Wettability for Condensate Microdrop Self-Propelling Based on Designed Superhydrophobic TiO2 Nanostructures

The ability to release the adhered drops on superhydrophobic surfaces is very important for self-cleaning, antifrosting/icing, microfluidic device, and heat transfer applications. In this paper, three types of in situ electrochemical anodizing TiO₂ nanostructure films are rationally designed and fabricated on titanium substrates with special superwettability, viz., TiO₂ nanotube arrays, irregular TiO₂ nanotube arrays, and hierarchical TiO₂ particle arrays (HTPA), and their corresponding behavior in condensate microdrop self-propelling (CMDSP) is investigated. Compared to the flat titanium counterpart, all three types of rough TiO₂ samples demonstrate a uniform distribution of smaller microscale droplets. Among the treated surfaces, the HTPA possesses the highest condensate density, and more than 80% of the droplets possess a diameter below 10 μm. Theoretical analysis indicates that the feature is mainly due to the morphology and structure induced extremely low droplet adhesion on super-antiwetting TiO₂ hierarchical surfaces, where the excess surface energy released from the migration leads to the self-propelling of merged microdrop. This work offers a way to rationally construct CMDSP surfaces with excellent self-cleaning, antifrosting/icing ability, and enhanced condensation heat transfer efficiency.

One-dimensional TiO2 Nanotube Photocatalysts for Solar Water Splitting

Hydrogen production from water splitting by photo/photoelectron-catalytic process is a promising route to solve both fossil fuel depletion and environmental pollution at the same time. Titanium dioxide (TiO2) nanotubes have attracted much interest due to their large specific surface area and highly ordered structure, which has led to promising potential applications in photocatalytic degradation, photoreduction of CO2, water splitting, supercapacitors, dye-sensitized solar cells, lithium-ion batteries and biomedical devices. Nanotubes can be fabricated via facile hydrothermal method, solvothermal method, template technique and electrochemical anodic oxidation. In this report, we provide a comprehensive review on recent progress of the synthesis and modification of TiO2 nanotubes to be used for photo/photoelectro-catalytic water splitting. The future development of TiO2 nanotubes is also discussed.

Recent advances on smart TiO2 nanotube platforms for sustainable drug delivery applications

To address the limitations of traditional drug delivery, TiO2 nanotubes (TNTs) are recognized as a promising material for localized drug delivery systems. With regard to the excellent biocompatibility and physicochemical properties, TNTs prepared by a facile electrochemical anodizing process have been used to fabricate new drug-releasing implants for localized drug delivery. This review discusses the development of TNTs applied in localized drug delivery systems, focusing on several approaches to control drug release, including the regulation of the dimensions of TNTs, modification of internal chemical characteristics, adjusting pore openings by biopolymer coatings, and employing polymeric micelles as drug nanocarriers. Furthermore, rational strategies on external conditions-triggered stimuli-responsive drug release for localized drug delivery systems are highlighted. Finally, the review concludes with the recent advances on TNTs for controlled drug delivery and corresponding prospects in the future.

TiO2 nanotube platforms for smart drug delivery: a review

Titania nanotube (TNT) arrays are recognized as promising materials for localized drug delivery implants because of their excellent properties and facile preparation process. This review highlights the concept of localized drug delivery systems based on TNTs, considering their outstanding biocompatibility in a series of ex vivo and in vivo studies. Considering the safety of TNT implants in the host body, studies of the biocompatibility present significant importance for the clinical application of TNT implants. Toward smart TNT platforms for sustainable drug delivery, several advanced approaches were presented in this review, including controlled release triggered by temperature, light, radiofrequency magnetism, and ultrasonic stimulation. Moreover, TNT implants used in medical therapy have been demonstrated by various examples including dentistry, orthopedic implants, cardiovascular stents, and so on. Finally, a future perspective of TNTs for clinical applications is provided.

Facile fabrication of organic/inorganic nanotube heterojunction arrays for enhanced photoelectrochemical water splitting

Organic/inorganic heterojunction photoanodes are appealing for making concurrent use of the highly photoactive organic semiconductors, and the efficient dielectric screening provided by their inorganic counterparts. In the present work, organic/inorganic nanotube heterojunction arrays composed of TiO2 nanotube arrays and a semiconducting N,N-(dicyclohexyl) perylene-3,4,9,10-tetracarboxylic diimide (PDi) layer were fabricated for photoelectrochemical water splitting. In this arrayed architecture, a PDi layer with a tunable thickness was coated on anodic TiO2 nanotube arrays by physical vapor deposition, which is advantageous for the formation of a uniform layer and an adequate interface contact between PDi and TiO2. The obtained PDi/TiO2 junction exhibited broadened visible light absorption, and an effective interface for enhanced photogenerated electron-hole separation, which is supported by the reduced charge transfer resistance and prolonged excitation lifetime via impedance spectroscopy analysis and fluorescence emission decay investigations. Consequently, such a heterojunction photoanode was photoresponsive to a wide visible light region of 400-600 nm, and thus demonstrated a highly enhanced photocurrent density at 1.23 V vs. a reversible hydrogen electrode. Additionally, the durability of such a photoanode can be guaranteed after long-time illumination because of the geometrical restraint imposed by the PDi aggregates. These results pave the way to discover new organic/inorganic assemblies for high-performance photoelectric applications and device integration.

In situ plasmonic Ag nanoparticle anchored TiO2 nanotube arrays as visible-light-driven photocatalysts for enhanced water splitting

An ultrasonication-assisted in situ deposition strategy was utilised to uniformly decorate plasmonic Ag nanoparticles on vertically aligned TiO2 nanotube arrays (NTAs) to construct a Ag@TiO2 NTA composite. The Ag nanoparticles act as efficient surface plasmon resonance (SPR) photosensitizers to drive photocatalytic water splitting under visible light irradiation. The Ag nanoparticles were uniformly deposited on the surface and inside the highly oriented TiO2 nanotubes. The visible-light-driven hydrogen production activities of silver nanoparticle anchored TiO2 nanotube array photocatalysts were evaluated using methanol as a sacrificial reagent in water under a 500 W Xe lamp with a UV light cutoff filter (λ ≥ 420 nm). It was found that the hydrogen production rate of the Ag@TiO2 NTAs prepared with ultrasonication-assisted deposition for 5 min was approximately 15 times higher than that of its pristine TiO2 NTAs counterpart. The highly efficient photocatalytic hydrogen evolution is attributed to the SPR effect of Ag for enhanced visible light absorption and boosting the photogenerated electron-hole separation/transfer. This strategy is promising for the design and construction of high efficiency TiO2 based photocatalysts for solar energy conversion.

Size-controllable synthesis of Bi/Bi2O3 heterojunction nanoparticles using pulsed Nd:YAG laser deposition and metal-semiconductor-heterojunction-assisted photoluminescence

We synthesized Bi/Bi2O3 heterojunction nanoparticles at various substrate temperatures using the pulsed laser deposition (PLD) technique with a pulsed Nd:YAG laser. The Bi/Bi2O3 heterojunction nanoparticles consisted of Bi nanoparticles and Bi2O3 surface layers. The average diameter of the Bi nanoparticles and the thickness of the Bi2O3 surface layer are linearly proportional to the substrate temperature. The heterojunctions between the Bi nanoparticles and Bi2O3 surface layers, which are the metal-semiconductor heterojunctions, can strongly enhance the photoluminescence (PL) of the Bi/Bi2O3 nanoparticles, because the metallic Bi nanoparticles can provide massive free Fermi-level electrons for the electron transitions in the Bi2O3 surface layers. The enhancement of PL emission at room temperature by metal-semiconductor-heterojunctions make the Bi/Bi2O3 heterojunction nanoparticles potential candidates for use in optoelectronic nanodevices, such as light-emitting diodes (LEDs) and laser diodes (LDs).

Enhanced photocatalytic activity of hierarchical three dimensional metal oxide@CuO nanostructures towards the degradation of Congo red dye under solar radiation

In the present study, we report a two step method for the synthesis of metal oxide (ZnO and Fe₃O₄) deposited on CuO nanowire arrays over 3D copper foam using thermal oxidation followed by microwave-assisted deposition.

Near-IR responsive nanostructures for nanobiophotonics: emerging impacts on nanomedicine

Nanobiophotonics is an emerging field at the intersection of nanoscience, photonics, and biotechnology. Harnessing interactions of light with nanostructures enables new types of bioimaging, sensing, and light-activated therapy which can make a major impact on nanomedicine. Low penetration through tissue limits the use of visible light in nanomedicine. Near infrared (NIR) light (~780-1100 nm) can penetrate significantly further, enabling free-space delivery into deep tissues. This review focuses on interactions of NIR light with nanostructures to produce three effects: direct photoactivation, photothermal effects, and photochemical effects. Applications of direct photoactivation include bioimaging and biosensing using NIR-emitting quantum dots, materials with localized surface plasmon resonance (LSPR) in the NIR, and upconverting nanoparticles. Two key nanomedicine applications using photothermal effects are photothermal therapy (PTT), and photoacoustic (PA) imaging. For photochemical effects, we present the latest advances in in-situ upconversion and upconverting nanostructures for NIR activation of photodynamic therapy (PDT).

FROM THE CLINICAL EDITOR

Nanobiophotonics is a relatively new field applying light for the interactions with nanostructures, which can be used in bioimaging, sensing, and therapy. As near infrared (NIR) light (~780-1100 nm) can have better tissue penetration, its clinical potential is far greater. In this review, the authors discussed the latest research on the applications of NIR light in imaging and therapeutics.