Eco-friendly and sustainable process for recovery of sulfate from paper mill mixed salt: Recycling of sulfate for dye fixation process

Paper mill Electrostatic Precipitator (ESP) ash contains a mixture of alkali metal chloride (34.2 %) and sulfate (84.2 %) which has serious negative effects on the environment and makes it more expensive and constrained to dispose ESP ash. Therefore, handling and recycling ESP ash demands extra thought when disposing of it. Present study, aimed to separate chloride and sulfate from ESP ash using electrochemical membrane technology. Three different concentrations of ESP ash solution such as 200 g L-1, 320 g L-1 and 450 g L-1 were used as the electrolyte. Ti/TiO2-IrO2-RuO2 and titanium (Ti) are used as anode and cathode respectively. Caustic and sulfate solutions were recovered at the respective compartments. The collected sulfate solution was dried by solar light to convert 99 % sulfate salts as confirmed by Energy-dispersive X-ray analysis (EDAX) analysis. Recovered sulfate salt was used for the dye fixing process, in which the colour fixing difference of ΔE value was about 2.10 and the strength of the dye was about 86.72 %. Therefore, the textile industry can repurpose the recovered sulfate salt for the dye fixing process.

Degradation of phenol using Fe(II)-activated CaO2: effect of ball-milled activated carbon (ACBM) addition

In-situ chemical oxidation (ISCO) based on peroxide activation is one of the most promising technologies for removing organic contaminants from natural groundwater (NGW). However, use of the most common form of hydrogen peroxide (H₂O₂) is limited owing to its significantly rapid reaction rate and heat generation. Therefore, in the present study, the activation of calcium peroxide (CaO₂), a slow H₂O₂ releasing agent, by Fe(II) was proposed (CaO₂/Fe(II)), and the phenol degradation mechanisms and feasibility of NGW remediation were investigated. The optimum molar ratio of [phenol]/[CaO₂]/[Fe(II)] (phenol = 0.5 mM) was 1/10/10, resulting in 87.0-92.5% phenol removal within 120 min under a broad initial pH range of 3-9. HCO₃^-, PO₄^3-, and humic acid significantly inhibited degradation, whereas the effects of Cl^-, NO₃^-, and SO₄^2- were negligible. Reactive oxygen species (ROS) were identified based on the results of phenol degradation in the presence of scavengers and electron spin resonance (ESR) spectroscopy, which demonstrated that ¹O₂ played the dominant role, supported by ^•OH, in CaO₂/Fe(II). Phenol removal in NGW (67.81%) was less than that in distilled and deionized water (DIW, 92.5%) at a [phenol]/[CaO₂]/[Fe(II)] ratio of 1/10/10. However, phenol removal was significantly improved (∼100%) by increasing the CaO₂ and Fe(II) doses to 1/20/20-40. Furthermore, when 125-250 mg L^-1 of ball-milled activated carbon (AC_BM) was added (CaO₂/Fe(II)-AC_BM), phenol removal was enhanced from 67.81% to 90.94-100% in the NGW. CaO₂/Fe(II)-AC_BM exhibited higher total organic carbon (TOC) removal than CaO₂/Fe(II). In addition, no notable by-products were detected using CaO₂/Fe(II)-AC_BM, whereas the polymerisation products of hydroxylated and/or ring-cleaved compounds, that is, aconitic acid, gallocatechin, and 10-hydroxyaloin, were found in the reaction with CaO₂/Fe(II). These results strongly suggest that CaO₂/Fe(II)-AC_BM is highly promising for groundwater remediation, minimizing degradation byproducts and the adverse effects caused by the NGW components.

Beyond dumping: New strategies in the separation of preservative salt from tannery waste mixed salt and its reuse for tannery industrial application

The tannery effluent treatment plants produce tonnes of waste in the form of mixed salts containing sodium chloride, sulfate, calcium, and magnesium salts. Disposal of these mixed salts may create an environmental problem. The proposed method broadly consists of the separation of sodium chloride from reverse osmosis (RO) reject and raw-hide waste salt (preservative salt) of the tannery. This study used the physicochemical method to treat waste salt from tannery industrial waste. The addition of sodium hydroxide and sodium carbonate improved calcium and magnesium removal efficiency in the RO reject and preservative waste salts. The optimization of the sodium salt of hydroxide and carbonate is very important to remove an unwanted substance from waste salt. The sodium chloride was recovered, and the purity was about >98% which was successfully reused as preservative salt as well as in the pickling process in the tannery industry.

A converged approach of electro-biological process for decolorization and degradation of toxic synthetic dyes

Being one of the leading industries worldwide, the textile industry has been consuming large quantities of groundwater and discharging huge volumes of dye-contaminated effluents into our aquatic environment. Augmentation of water sources via reuse of treated effluents is therefore highly necessary. In the present study, the decolorization and degradation of synthetic toxic dye from an aqueous solution were investigated through an electro-biological route. Initially, decolorization of synthetic dye solutions (100, 500, and 1000 mg L^-1) was carried out by electrooxidation process using mixed metal oxide and titanium as anode and cathode, respectively. The electrooxidation solutions were further treated using bacteria (Pseudomonas aeruginosa) that were isolated from petroleum-transporting pipelines. UV-Vis, TOC, chemical oxygen demand, and NMR analyses revealed that the biodegradation process with electrooxidation enhanced the mineralization of the synthetic dye solutions. An optimum NaCl electrolyte concentration of 3 g L^-1 was sufficient to produce reactive species viz., free chlorine and hypochlorite, which are responsible for the Reactive Blue 19 (RB-19) decolorization. Among the three RB-19 concentrations, the highest removal percentage was noticed at 100 mg L^-1 (100%) with energy consumption and energy costs equal to 5.44 kWh m^-3 and 0.65 USD m^-3, respectively.

Electrochemical Disinfection of Simulated Ballast Water Using RuO2-TiO2/Ti Electrode

The present work investigated the treatment of ballast water via electrochemical disinfection using a RuO₂-TiO₂/Ti electrode. Batch tests were conducted with simulated ballast water containing Escherichia coli as an indicator organism. The effect of varying NaCl concentrations (1%, 2%, and 3%; w/v) and current densities (0.3, 1.0, 2.0, and 3.0 mA/cm²) on the inactivation of E. coli was examined. Results showed higher disinfection efficiency of E. coli was obtained at higher NaCl concentration and current density. Complete inactivation of E. coli was attained within 2 and 1 min at 0.3 and 1 mA/cm², respectively, under 3% NaCl concentration. Meanwhile, complete disinfection at 1 and 2% NaCl concentrations was observed in 6 and 2 min, respectively, using a current density of 0.3 mA/cm². The 100% inactivation of E. coli was achieved with an energy consumption in the range of 2.8 to 2.9 Wh/m³ under the NaCl concentrations at 1 mA/cm² and 1 min of electrolysis time. The complete disinfection attained within 1 min meets the D-2 standard (<250 CFU E. coli/100 mL) of ballast water under the International Maritime Organization. The values of energy consumption of the present work are lower than previous reports on the inactivation of E. coli from simulated ballast water.

High throughput techniques for the rapid identification of electroactive microorganisms

Electroactive microorganisms (EAM), capable of executing extracellular electron transfer (EET) in/out of a cell, are employed in microbial electrochemical technologies (MET) and bioelectronics for harnessing electricity from wastewater, bioremediation and as biosensors. Thus, investigation on EAM is becoming a topic of interest for multidisciplinary areas, such as environmental science, energy and health sectors. Though, EAM are widespread in three domains of life, nevertheless, only a few hundred EAM have been identified so far and hence, the rapid identification of EAM is imperative. In this review, the techniques that are developed for the direct identification of EAM, such as azo dye and WO₃ based techniques, dielectrophoresis, potentiostatic/galvanometric techniques, and other indirect methods, such as spectroscopy and molecular biology techniques, are highlighted with a special focus on time required for the detection of these EAM. The bottlenecks for identifying EAM and the knowledge gaps based on the present investigations are also discussed. Thus, this review is intended to encourage researchers for devolving high-throughput techniques for identifying EAM with more accuracy, while consuming less time.

Efficient Fluoride Removal and Dye Degradation of Contaminated Water Using Fe/Al/Ti Oxide Nanocomposite

The trimetallic Fe/Al/Ti (1:1:1) nanocomposite (FAT), synthesized by an adaptable tuned chemical route, offers a new approach for water treatment, for example, the de-fluoridation and photodegradation soluble dye methylene blue (MB) at pH 7. FAT acted as a good fluoride scavenger in the presence of other co-ions and within a widespread pH range (pH 2-11). The photodegradation efficiencies were >90% for different concentrations of MB solutions. The characterization of FAT includes thermogravimetric analysis, X-ray diffraction, Fourier transform-infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and ζ-potential analysis. Furthermore, the regeneration efficiencies of both the water treatments were checked, where the removal efficiency was not hampered significantly even after five batches. Spectroscopic techniques were adopted to perform the kinetic studies and to propose the probable mechanistic paths.

"Green technology": Bio-stimulation by an electric field for textile reactive dye contaminated agricultural soil

The aim of the study is to degrade pollutants as well as to increase the fertility of agricultural soil by starch enhancing electrokinetic (EKA) and electro-bio-stimulation (EBS) processes. Starch solution was used as an anolyte and voltage gradient was about 0.5V/cm. The influence of bacterial mediated process was evaluated in real contaminated farming soil followed by pilot scale experiment. The in-situ formation of β-cyclodextrin from starch in the treatments had also influence on the significant removal of the pollutants from the farming soil. The conductivity of the soil was effectively reduced from 15.5dS/m to 1.5dS/m which corroborates well with the agricultural norms. The bio-stimulation was confirmed by the increase of the phosphorus content in the treated soil. Finally, phytotoxicity assays demonstrated the viability of the developed technique for soil remediation because plant germination percentage was higher in the treated soil in comparison to untreated soil.

Optimizing electroosmotic flow in an annulus from Debye Hückel approximation to Poisson–Boltzmann equation

Optimal EO pumping rates on the plane of zeta potentials with distribution of the inner radius of annular tube.