Effect of Reduction Methods on the Properties of Composite Films of Bacterial Cellulose-Silver Nanoparticles

Composite films of bacterial cellulose-silver nanoparticles (BC-Ag) were prepared by different methods of in situ reduction of silver ions, using sodium hydroxide, ascorbic acid, chitosan, and UV irradiation. The effects of the reduction methods on their properties were investigated. The chitosan-reduced composite exhibited dispersed silver nanoparticles (AgNPs) within the nanocellulose matrix with the smallest size, while the ascorbic-reduced composite displayed the largest size. The incorporation of AgNPs tended to reduce the crystallinity of the composites, except for the ascorbic-reduced composite, which exhibited an increase in crystallinity. Mechanical testing revealed that the ascorbic-reduced composite had the highest Young's modulus of 8960 MPa, whereas the UV-reduced composite had the highest tensile strength and elongation at break. Thermal analysis of BC-Ag composites indicated similar glass transition temperature and decomposition profiles to BC, with additional weight-loss steps at high temperatures. The sodium hydroxide-reduced composite demonstrated the highest electrical conductivity of 1.1 × 10^-7 S/cm. Water absorption capacity was reduced by the incorporation of AgNPs, except for the chitosan-reduced composite, which showed an enhanced water absorption capacity of 344%. All BC-Ag composites displayed very strong antibacterial activities against Staphylococcus aureus and Escherichia coli. These results also highlight the potential uses of BC-Ag composites for various applications.

Enhancing the Performance of Triboelectric Generator: A Novel Approach Using Solid-Liquid Interface-Treated Foam and Metal Contacts

This work introduces a novel approach for enhancing the performance of a triboelectric generator (TEG) by using a solid-liquid interface-treated foam (SLITF) as its active layer, combined with two metal contacts of different work functions. SLITF is made by absorbing water into a cellulose foam, which enables charges generated by friction energy during the sliding motion to be separated and transferred through the conductive path formed by the hydrogen-bonded network of water molecules. Unlike traditional TEGs, the SLITF-TEG demonstrates an impressive current density of 3.57 A/m² and can harvest electric power up to 0.174 W/m² with an induced voltage of approximately 0.55 V. The device generates a direct current in the external circuit, eliminating the limitations of low current density and alternating current found in traditional TEGs. By connecting six-unit cells of SLITF-TEG in series and parallel, the peak voltage and current can be increased up to 3.2 V and 12.5 mA, respectively. Furthermore, the SLITF-TEG has the potential to serve as a self-powered vibration sensor with high accuracy (R² = 0.99). The findings demonstrate the significant potential of the SLITF-TEG approach for efficiently harvesting low-frequency mechanical energy from the natural environment, with broad implications for a range of applications.

Research progress of the biosynthetic strains and pathways of bacterial cellulose

Bacterial cellulose is a glucose biopolymer produced by microorganisms and widely used as a natural renewable and sustainable resource in the world. However, few bacterial cellulose-producing strains and low yield of cellulose greatly limited the development of bacterial cellulose. In this review, we summarized the 30 cellulose-producing bacteria reported so far, including the physiological functions and the metabolic synthesis mechanism of bacterial cellulose, and the involved three kinds of cellulose synthases (type I, type II, and type III), which are expected to provide a reference for the exploration of new cellulose-producing microbes.

Removal of fluoride in aqueous medium under the optimum conditions through intracellular accumulation in Bacillus flexus (PN4)

The removal of fluoride is essential for water contaminated with fluoride before being utilized since the unsafe concentration of fluoride with respect to the permissible limits. In the present study, there are 61 bacterial strains belonging to fluoride tolerance were isolated from the contaminated soil of Dharmapuri District, Tamil Nadu, India and they were evaluated for different characterization. Among the strains isolated, the strain PN4 showed a high tolerance to fluoride ranging from 500 to 2500 ppm under different stress conditions. The strain PN4 was selected as a possible organism for the degradation and removal of fluoride in an aqueous medium. Based on the morphology, biochemical characteristics and the 16S rRNA sequencing, the bacterium PN4 was identified as Bacillus flexus. In batch mode studies, the glucose was showed the maximum removal of fluoride (86%) followed by beef extract (82%) and a significant level of defluoridation was observed at pH 7.0 and the temperature at 35°C. In the antibiotic-resistance pattern, the strain Bacillus flexus PN4 was shown sensitive to three different antibiotics. Intracellular accumulation of fluoride by the bacterial cell was characterized by SEM- EDAX, TEM and FTIR analysis.

Improved Hydrophobicity of a Bacterial Cellulose Surface: Click Chemistry in Action

The vast application potentials of bacterial cellulose (BC)-based materials for developing leather-like materials, wound-healing materials and electronic materials have been realized very recently. Surface functionalization of these materials can help in improvement of certain properties such as water repellency, mechanical strength, and so forth. In this paper, we reported functionalization of BC surfaces using "click" polymerization for the first time. By this methodology, dense aromatic groups have been incorporated for the improvement of hydrophobicity. For comparative studies, various fluorine-based compounds have been introduced using conventional click reactions. The surface-modified BC materials have been confirmed by various spectroscopic methods. Particularly, the chemical structures of the materials were studied by solid-state ¹³C NMR spectroscopy and attenuated total reflection-infrared spectroscopy. X-ray photoelectron spectroscopy was used to study the elemental composition of the materials. Moreover, the crystallite changes of modified BC surfaces were investigated by X-ray diffraction. Further, the changes in the morphology of the material after functionalization were evaluated by scanning electron microscopy and atomic force microscopy. Finally, water contact angle measurement revealed manyfold increase in hydrophobicity after click polymerization. A video is also provided in the Supporting Information to show the application potential of this material for developing leather-like materials.