Shell thickness effects on quantum dot brightness and energy transfer

Coherent InP/ZnS core@shell quantum dots with narrow-band green emissions

We report, for the first time, that the coherent growth of zinc sulfide (ZnS) on a colloidal indium phosphide (InP) quantum dot (QD) yields a InP/ZnS core/shell structure with a single lattice constant of 0.563 nm. Compared to the bulk crystal of zinc-blend (cubic) InP, the lattice of the core QD is compressed by 4.1%. In contrast, the lattice of the shell expands by 4.1% relative to the bulky ZnS crystal throughout the core/shell QD if the shell is thinner than or equal to 0.81 nm and the diameter of the core QD is smaller than 2.64 nm. Under these conditions, the bandgap of the core QD increases, resulting in a blueshift of absorption and photoluminescence (PL) spectra. The PL peak is centered at 523 nm. Furthermore, the PL quantum yield is enhanced up to 70% and the PL bandwidth narrows to 36 nm based on the strengthened quantum confinement effect. The temperature dependence of the PL properties is investigated to discuss the effect of the core/shell lattice coherency on the improved PL performances.

The quantum dot vs. organic dye conundrum for ratiometric FRET-based biosensors: which one would you chose?

Förster resonance energy transfer (FRET) is a widely used and ideal transduction modality for fluorescent based biosensors as it offers high signal to noise with a visibly detectable signal. While intense efforts are ongoing to improve the limit of detection and dynamic range of biosensors based on biomolecule optimization, the selection of and relative location of the dye remains understudied. Herein, we describe a combined experimental and computational study to systematically compare the nature of the dye, i.e., organic fluorophore (Cy5 or Texas Red) vs. inorganic nanoparticle (QD), and the position of the FRET donor or acceptor on the biomolecular components. Using a recently discovered transcription factor (TF)-deoxyribonucleic acid (DNA) biosensor for progesterone, we examine four different biosensor configurations and report the quantum yield, lifetime, FRET efficiency, IC50, and limit of detection. Fitting the computational models to the empirical data identifies key molecular parameters driving sensor performance in each biosensor configuration. Finally, we provide a set of design parameters to enable one to select the fluorophore system for future intermolecular biosensors using FRET-based conformational regulation in in vitro assays and new diagnostic devices.

The Rise and Future of Discrete Organic-Inorganic Hybrid Nanomaterials

Hybrid nanomaterials (HNs), the combination of organic semiconductor ligands attached to nanocrystal semiconductor quantum dots, have applications that span a range of practical fields, including biology, chemistry, medical imaging, and optoelectronics. Specifically, HNs operate as discrete, tunable systems that can perform prompt fluorescence, energy transfer, singlet fission, upconversion, and/or thermally activated delayed fluorescence. Interest in HNs has naturally grown over the years due to their tunability and broad spectrum of applications. This Review presents a brief introduction to the components of HNs, before expanding on the characterization and applications of HNs. Finally, the future of HN applications is discussed.

Influence of particle architecture on the photoluminescence properties of silica-coated CdSe core/shell quantum dots

Light-emitting nanoparticles like semiconductor nanocrystals (termed quantum dots, QDs) are promising candidates for biosensing and bioimaging applications based on their bright and stable photoluminescent properties. As high-quality QDs are often synthesized in organic solvents, strategies needed to be developed to render them water-dispersible without affecting their optical properties and prevent changes in postmodification steps like the biofunctionalization with antibodies or DNA. Despite a large number of studies on suitable surface modification procedures, the preparation of water-soluble QDs for nanobiotechnology applications still presents a challenge. To highlight the advantages of surface silanization, we systematically explored the influence of the core/multishell architecture of CdSe/CdS/ZnS QDs and the silanization conditions on the optical properties of the resulting silanized QDs. Our results show that the optical properties of silica-coated CdSe/CdS/ZnS QDs are best preserved in the presence of a thick CdS (6 monolayers (ML)) intermediate shell, providing a high photoluminescence quantum yield (PL QY), and a relatively thick ZnS (4.5 ML) external shell, effectively shielding the QDs from the chemical changes during silica coating. In addition to the QD core/shell architecture, other critical parameters of the silica-coating process, that can have an influence on the optical properties of the QD, include the choice of the surfactant and its concentration used for silica coating. The highest PL QY of about 46% was obtained by a microemulsion silica-coating procedure with the surfactant Brij L4, making these water-dispersible QDs to well-suited optical reporters in future applications like fluorescence immunoassays, biomedicine, and bioimaging.

Electric field induced macroscopic cellular phase of nanoparticles

A suspension of nanoparticles with very low volume fraction is found to assemble into a macroscopic cellular phase that is composed of particle-rich walls and particle-free voids under the collective influence of AC and DC voltages. Systematic study of this phase transition shows that it was the result of electrophoretic assembly into a two-dimensional configuration followed by spinodal decomposition into particle-rich walls and particle-poor cells mediated principally by electrohydrodynamic flow. This mechanistic understanding reveals two characteristics needed for a cellular phase to form, namely (1) a system that is considered two dimensional and (2) short-range attractive, long-range repulsive interparticle interactions. In addition to determining the mechanism underpinning the formation of the cellular phase, this work presents a method to reversibly assemble microscale continuous structures out of nanoscale particles in a manner that may enable the creation of materials that impact diverse fields including energy storage and filtration.

Ultrafast separation of multiexcitons within core/shell quantum dot hybrid systems

We investigated the electron transfer processes in methylene blue-CdTe and methylene blue-CdTe/CdSe complexes by steady state and femtosecond transient absorption spectroscopy by selective excitation of the quantum dot (QD) moiety. The ultrafast electron transfer is accelerated by the shell growth due to the separation of the charge carriers and the resulting increase of electron density in the shell. Transmission electron microscope images show that the successive addition of shell material deforms the spherical QDs until they adopt a tetrapodal shape. The increased donor-acceptor distance in the tetrapodal CdTe/CdSe QDs leads to a slower electron transfer. Photon flux dependent transient absorption measurements indicate the separation of two electrons for the QDs with a thin shell and thus demonstrate that charge carrier multiplication can be directly utilized for increased charge transfer in this type of QD hybrid system.

Tuning Hot Carrier Dynamics of InP/ZnSe/ZnS Quantum Dots by Shell Morphology Control

Isotropic InP/ZnSe/ZnS quantum dots (QDs) are prepared at a high reaction temperature, which facilitates ZnSe shell growth on random facets of the InP core. Fast crystal growth enables stacking faults elimination, which induces anisotropic growth, and as a result, improves the photoluminescence (PL) quantum yield by nearly 20%. Herein, the effect of the QD morphology on photophysical properties is investigated by observing the PL blinking and ultrafast charge carrier dynamics. It is found that hot hole trapping is considerably suppressed in isotropic InP QDs, indicating that the stacking faults in the anisotropic InP/ZnSe structures act as defects for luminescence. These results highlight the importance of understanding the correlation between QD shapes and hot carrier dynamics, and present a way to design highly luminescent QDs for further promising display applications.

Mapping the effect of geometry on the radiative rate in core/shell QDs: core size dictates the conduction band offset

Computational models have been developed that can accurately predict the electronic structure and thus optical properties of a variety of quantum dot (QD) materials. However, the application of these models to core/shell and other heterostructured QDs has received less experimental corroboration owing to the difficulty in systematically synthesizing and characterizing large ranges of geometries. In the current work, we synthesized a library of core/shell CdSe/CdS QDs with varying core sizes and shell thicknesses, and have characterized their radiative recombination rates. We find that the core size has only a modest effect on the radiative recombination rates, far less than is predicted by conventional effective mass models. In order to theoretically describe the experimental data, we performed an empirical modification of an effective mass model. We find that the conduction band offset between CdSe and CdS must be empirically altered based on QD core size in order to match our experimental data. This is hypothesized to be a result of reduced interfacial strain in core/shell QDs with smaller cores. The resultant relationship between conduction band offset and core size is used to create a predictive map of radiative lifetime as a function of core size and shell thickness. This map will be useful to researchers implementing CdSe/CdS core/shell QDs for a variety of applications since it can provide geometry specific excited state lifetimes.

Predicting the radiative rate in CdSe/CdS core/shell quantum dots is made possible by using a core-size-dependent conduction band offset.

Extending the Near-Infrared Emission Range of Indium Phosphide Quantum Dots for Multiplexed In Vivo Imaging

This report of the reddest emitting indium phosphide quantum dots (InP QDs) to date demonstrates tunable, near-infrared (NIR) photoluminescence (PL) as well as PL multiplexing in the first optical tissue window while avoiding toxic constituents. This synthesis overcomes the InP "growth bottleneck" and extends the emission peak of InP QDs deeper into the first optical tissue window using an inverted QD heterostructure, specifically ZnSe/InP/ZnS core/shell/shell nanoparticles. The QDs exhibit InP shell thickness-dependent tunable emission with peaks ranging from 515-845 nm. The high absorptivity of InP yields effective photoexcitation of the QDs with UV, visible, and NIR wavelengths. These nanoparticles extend the range of tunable direct-bandgap emission from InP-based nanostructures, effectively overcoming a synthetic barrier that has prevented InP-based QDs from reaching their full potential as NIR imaging agents. Multiplexed lymph node imaging in a mouse model demonstrates the potential of the NIR-emitting InP particles for in vivo imaging.

Engineering Brightness Matched Indium Phosphide Quantum Dots

The size-dependent optoelectronic properties of semiconductor nanocrystals quantum dots (QDs) are hugely beneficial for color tunability but induce an inherent relative PL brightness mismatch in QDs emitting different colors, as larger emitters absorb more incident photons than smaller particles. Here, we examine the effect of core composition, shell composition, and shell thickness on optical properties including high energy absorption, quantum yield (QY), and the relative brightness of InP/ZnS and InP/ZnSe core/shell and InP/ZnSe/ZnS core/shell/shell QDs at different excitation wavelengths. Our analysis reveals that the presence of an intermediate ZnSe shell changes the wavelength of enhanced absorption onset and leads to highly excitation wavelength dependent QYs. Switching from commercial CdSe/ZnS to InP/ZnS reduces the brightness-mismatch between green and red emitters from 33- to 5-fold. Incorporating a 4-monolayer thick optically absorbing ZnSe shell into the QD heterostructure and heating the QDs in a solution of zinc oleate and trioctylphosphine produces InP/ZnSe/ZnS QDs that are ~10-fold brighter than their InP/ZnS counterparts. In contrast to CdSe/CdS/ZnS core/shell/shell QDs, which only photoluminesce at red wavelengths with thicker CdS shells due to their Quasi-Type II bandstructure, Type I InP/ZnSe/ZnS QDs are uniquely suited to creating a rainbow of visible-emitting, brightness matched emitters. By tailoring the thickness of the intermediate ZnSe shell, heavy metal-free, brightness-matched green and red emitters are produced. This study highlights the ability to overcome the inherent brightness mismatch seen in QDs through concerted materials design of heterostructured core/shell InP-based QDs.

Phase Transfer and DNA Functionalization of Quantum Dots Using an Easy-to-Prepare, Low-Cost Zwitterionic Polymer

Small, stable, and bright quantum dots (QDs) are of interest in many biosensing and biomedical imaging applications, but current methodologies for obtaining these characteristics can be highly specialized or expensive. We describe a straightforward, low-cost protocol for functionalizing poly(isobutylene-alt-maleic anhydride) (PIMA) with moieties that anchor to the QD surface (histamine), impart hydrophilicity [(2-aminoethyl)trimethylammonium chloride (Me₃N⁺-NH₂)], and provide a platform for biofunctionalization via click chemistry (dibenzocyclooctyne (DBCO)). Guidelines to successfully use this polymer for QD ligand exchange are presented, and an example of biofunctionalization with DNA is shown. Stable QD-DNA conjugates are obtained with high yield and without requiring additional purification steps.

Combining HR-TEM and XPS to elucidate the core-shell structure of ultrabright CdSe/CdS semiconductor quantum dots

Controlling thickness and tightness of surface passivation shells is crucial for many applications of core–shell nanoparticles (NP). Usually, to determine shell thickness, core and core/shell particle are measured individually requiring the availability of both nanoobjects. This is often not fulfilled for functional nanomaterials such as many photoluminescent semiconductor quantum dots (QD) used for bioimaging, solid state lighting, and display technologies as the core does not show the application-relevant functionality like a high photoluminescence (PL) quantum yield, calling for a whole nanoobject approach. By combining high-resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS), a novel whole nanoobject approach is developed representatively for an ultrabright oleic acid-stabilized, thick shell CdSe/CdS QD with a PL quantum yield close to unity. The size of this spectroscopically assessed QD, is in the range of the information depth of usual laboratory XPS. Information on particle size and monodispersity were validated with dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) and compared to data derived from optical measurements. In addition to demonstrating the potential of this novel whole nanoobject approach for determining architectures of small nanoparticles, the presented results also highlight challenges faced by different sizing and structural analysis methods and method-inherent uncertainties.

Transcription Factor Based Small-Molecule Sensing with a Rapid Cell Phone Enabled Fluorescent Bead Assay

Recently, allosteric transcription factors (TFs) were identified as a novel class of biorecognition elements for in vitro sensing, whereby an indicator of the differential binding affinity between a TF and its cognate DNA exhibits dose-dependent responsivity to an analyte. Described is a modular bead-based biosensor design that can be applied to such TF-DNA-analyte systems. DNA-functionalized beads enable efficient mixing and spatial separation, while TF-labeled semiconductor quantum dots serve as bright fluorescent indicators of the TF-DNA bound (on bead) and unbound states. The prototype sensor for derivatives of the antibiotic tetracycline exhibits nanomolar sensitivity with visual detection of bead fluorescence. Facile changes to the sensor enable sensor response tuning without necessitating changes to the biomolecular affinities. Assay components self-assemble, and readout by eye or digital camera is possible within 5 minutes of analyte addition, making sensor use facile, rapid, and instrument-free.

Surface Immobilized Nucleic Acid-Transcription Factor Quantum Dots for Biosensing

Immobilization of biosensors on surfaces is a key step toward development of devices for real-world applications. Here the preparation, characterization, and evaluation of a surface-bound transcription factor-nucleic acid complex for analyte detection as an alternative to conventional systems employing aptamers or antibodies are described. The sensor consists of a gold surface modified with thiolated Cy5 fluorophore-labeled DNA and an allosteric transcription factor (TetR) linked to a quantum dot (QD). Upon addition of anhydrotetracycline (aTc)-the analyte-the TetR-QDs release from the surface-bound DNA, resulting in loss of the Förster resonance energy transfer signal. The sensor responds in a dose-dependent manner over the relevant range of 0-200 µm aTc with a limit of detection of 80 nm. The fabrication of the sensor and the subsequent real-time quantitative measurements establish a framework for the design of future surface-bound, affinity-based biosensors using allosteric transcription factors for molecular recognition.

Quantum dot to quantum dot Förster resonance energy transfer: engineering materials for visual color change sensing

In this work, quantum dots (QDs) of various heterostructured compositions and shell thicknesses are used as Förster or fluorescence resonance energy transfer (FRET) donors and acceptors to optimize QD-QD FRET sensing through materials design. While several reports have highlighted the advantages of using QD-dye, rather than dye-dye, FRET in sensing applications, QD-QD FRET has lagged behind in development as a result of high background signal from direct acceptor excitation. However, in designing sensors for longitudinal studies, QD-dye sensors are limited by the photostability of the fluorescent dye. While fluorescence generally affords higher sensitivity than absorbance-based readouts, the instrumentation needed for detecting fluorescence can be expensive, motivating the development of sensors bright enough to be seen by eye or imaged with cheap consumer electronics. Harnessing the exceptional brightness of QDs, our study focuses on the development of QD-QD FRET pairs where color change is achieved for visual readout and instrument-free sensing. We demonstrate that bulk semiconductor material characteristics can be used to a priori predict and tailor the behavior of QD-QD FRET systems, and our findings show that it is possible to create QD donors that are brighter than their acceptors through concerted compositional and morphological choices in heterostructured QDs. This is significant for developing visual sensors, as we show that the most profound color change occurs when the direct acceptor emission is lower than that of the donor. Finally, the use of an optimal cadmium-free QD-QD FRET pair is presented in a pH sensor that shows a large range of pH-dependent color change with bright, instrument-free readout.

A Förster Resonance Energy Transfer-Based Ratiometric Sensor with the Allosteric Transcription Factor TetR

A recent description of an antibody-free assay is significantly extended for small molecule analytes using allosteric transcription factors (aTFs) and Förster resonance energy transfer (FRET). The FRET signal indicates the differential binding of an aTF-DNA pair with a dose-dependent response to its effector molecule, i.e., the analyte. The new sensors described here, based on the well-characterized aTF TetR, demonstrate several new features of the assay approach: 1) the generalizability of the sensors to additional aTF-DNA-analyte systems, 2) sensitivity modulation through the choice of donor fluorophore (quantum dots or fluorescent proteins, FPs), and 3) sensor tuning using aTF variants with differing aTF-DNA binding affinities. While all of these modular sensors self-assemble, the design reported here based on a recombinant aTF-FP chimera with commercially available dye-labeled DNA uses readily accessible sensor components to facilitate easy adoption of the sensing approach by the broader community.

A progesterone biosensor derived from microbial screening

Bacteria are an enormous and largely untapped reservoir of biosensing proteins. We describe an approach to identify and isolate bacterial allosteric transcription factors (aTFs) that recognize a target analyte and to develop these TFs into biosensor devices. Our approach utilizes a combination of genomic screens and functional assays to identify and isolate biosensing TFs, and a quantum-dot Förster Resonance Energy Transfer (FRET) strategy for transducing analyte recognition into real-time quantitative measurements. We use this approach to identify a progesterone-sensing bacterial aTF and to develop this TF into an optical sensor for progesterone. The sensor detects progesterone in artificial urine with sufficient sensitivity and specificity for clinical use, while being compatible with an inexpensive and portable electronic reader for point-of-care applications. Our results provide proof-of-concept for a paradigm of microbially-derived biosensors adaptable to inexpensive, real-time sensor devices.

Efficient and Stable CdSe/CdS/ZnS Quantum Rods-in-Matrix Assembly for White LED Application

CdSe/CdS core-shell quantum rods (QRs) are a promising prospect in optoelectronic applications but usually have a relatively low quantum efficiency and stability. Here, we report on an efficient and stable CdSe/CdS/ZnS QRs-in-matrix assembly (QRAs) by growing and embedding CdSe/CdS QRs in ZnS matrices. Structural characterizations show that the CdSe/CdS QRs are encapsulated and interconnected by ZnS in the QRAs structure. The stable ZnS encapsulation renders the CdSe/CdS QRs high quantum efficiency (QE) up to 85%. The QRAs also present high photo- and thermal-stability and can preserve 93% of the initial QE at 100 °C. The QRAs powder presents a light degradation of only 2% under continuous excitation for 100 h, displaying profound potential in optoelectronic applications. White light-emitting diodes (WLEDs) are fabricated by packaging the QRAs powder as phosphor on top of blue GaN chip. The WLED shows high optical performance and light quality.

Encapsulating Quantum Dots in Lipid-PEG Micelles and Subsequent Copper-Free Click Chemistry Bioconjugation

The utility of quantum dots (QDs) for biological applications is predicated on stably dispersing the particles in aqueous media. During transfer from apolar organic solvents to water, the optical properties of the fluorescent nanoparticles must be maintained; additionally, the resulting colloid should be monodisperse and stable against aggregation. Furthermore, the hydrophilic coating should confer functional groups or conjugation handles to the QDs, as biofunctionalization is often critical to biosensing and bioimaging applications. Micelle encapsulation is an excellent technique for conferring hydrophilicity and conjugation handles to QDs. One interesting conjugation handle that can easily be added to the QDs is an azide group, which conjugates to strained alkynes via strain promoted azide-alkyne cycloaddition (SPAAC) reactions. SPAAC, or copper-free click chemistry, utilizes very mild reaction conditions, involves reactive groups that are bio-orthogonal, and is nearly quantitative. Micelle encapsulation is also very mild and preserves the optical properties of the QDs nearly perfectly. The combination of these approaches comprises a mild, effective, and straightforward approach to preparing functionalized QDs for biological applications.

Order-of-Magnitude, Broadband-Enhanced Light Emission from Quantum Dots Assembled in Multiscale Phase-Separated Block Copolymers

Achieving high emission efficiency in solid-state quantum dots (QDs) is an essential requirement for high-performance QD optoelectronics. However, most QD films suffer from insufficient excitation and light extraction efficiencies, along with nonradiative energy transfer between closely adjacent QDs. Herein, we suggest a highly effective strategy to enhance the photoluminescence (PL) of QD composite films through an assembly of QDs and poly(styrene-b-4-vinylpyridine)) (PS-b-P4VP) block copolymer (BCP). A BCP matrix casted under controlled humidity provides multiscale phase-separation features based on (1) submicrometer-scale spinodal decomposition between polymer-rich and water-rich phases and (2) sub-10 nm-scale microphase separation between polymer blocks. The BCP-QD composite containing bicontinuous random pores achieves significant enhancement of both light absorption and extraction efficiencies via effective random light scattering. Moreover, the microphase-separated morphology substantially reduces the Förster resonance energy transfer efficiency from 53% (pure QD film) to 22% (BCP-QD composite), collectively achieving an unprecedented 21-fold enhanced PL over a broad spectral range.

A versatile and accessible polymer coating for functionalizable zwitterionic quantum dots with high DNA grafting efficiency

Efficient and versatile functionalization of poly(anhydride maleic-alt-isobutylene) (PIMA), with economical commercial reagents, results in the one-step/one-day production of a copper-free click chemistry-ready carboxybetaine-like coating for quantum dots (QDs). The QDs are bright and stable in aqueous media and easily grafted with DNA with >95% efficiency.

Measuring Nanoparticle Polarizability Using Fluorescence Microscopy

Using a novel method developed to quantify the polarizability of photoluminescent nanoparticles in water, we present experimental observations of the extraordinary polarizability exhibited by nanoparticles of commensurate size with the Debye screening length, confirming previously reported theory. Semiconductor quantum dots (QDs) are ideal model nanoparticles to demonstrate this assay, due to their tunable size and bright photoluminescence. This assay is based upon microfluidic chambers with microelectrodes that generate trapping potentials that are weaker than thermal energy. By comparing the local electric field strength and variations in QD concentration, their polarizability was computed and found to agree with estimates based upon the hydrodynamic diameter found using light scattering. Strikingly, the polarizability of the nanoparticles increased 30-fold in low salt conditions compared to high salt conditions due to the increased thickness of the Debye layer relative to the particle radius. In addition to providing evidence that corroborates theoretical work studying direct solutions to the Poisson-Nernst-Planck equations, these observations provide an explanation for the previously observed conductivity dependence of biomolecule polarizability. As the polarizability of nanoparticles is of high importance to the electrically directed assembly of particles, as well as their interactions with other materials in complex environments, we anticipate that these results will be highly relevant to ongoing efforts in materials by design and nanomedicine.

In Vivo Biosensing Using Resonance Energy Transfer

Solution-phase and intracellular biosensing has substantially enhanced our understanding of molecular processes foundational to biology and pathology. Optical methods are favored because of the low cost of probes and instrumentation. While chromatographic methods are helpful, fluorescent biosensing further increases sensitivity and can be more effective in complex media. Resonance energy transfer (RET)-based sensors have been developed to use fluorescence, bioluminescence, or chemiluminescence (FRET, BRET, or CRET, respectively) as an energy donor, yielding changes in emission spectra, lifetime, or intensity in response to a molecular or environmental change. These methods hold great promise for expanding our understanding of molecular processes not just in solution and in vitro studies, but also in vivo, generating information about complex activities in a natural, organismal setting. In this review, we focus on dyes, fluorescent proteins, and nanoparticles used as energy transfer-based optical transducers in vivo in mice; there are examples of optical sensing using FRET, BRET, and in this mammalian model system. After a description of the energy transfer mechanisms and their contribution to in vivo imaging, we give a short perspective of RET-based in vivo sensors and the importance of imaging in the infrared for reduced tissue autofluorescence and improved sensitivity.

Heuristics from Modeling of Spectral Overlap in Förster Resonance Energy Transfer (FRET)

Among the photophysical parameters that underpin Förster resonance energy transfer (FRET), perhaps the least explored is the spectral overlap term ( J). While by definition J increases linearly with acceptor molar absorption coefficient (ε_(A) in M^-1 cm^-1), is proportional to wavelength (λ⁴), and depends on the degree of overlap of the donor fluorescence and acceptor absorption spectra, the question arose as to the value of J for the case of perfect spectral overlap versus that for representative fluorophores with incomplete spectral overlap. Here, Gaussian distributions of absorption and fluorescent spectra have been modeled that encompass varying degrees of overlap, full-width-at-half-maximum (fwhm), and Stokes shift. For ε_(A) = 10⁵ M^-1 cm^-1 and perfect overlap, the J value (in M^-1 cm^-1 nm⁴) ranges from 1.15 × 10¹⁴ (200 nm) to 7.07 × 10¹⁶ (1000 nm), is almost linear with λ⁴ (average of λ_abs and λ_flu), and is nearly independent of fwhm. For visible-region fluorophores with perfectly overlapped Gaussian spectra, the resulting value of J ( J_G-0) is ∼0.71 ε_(A)λ⁴ (M^-1 cm^-1 nm⁴). The experimental J values for homotransfer, as occurs in light-harvesting antennas, were calculated with spectra from a static database of 60 representative compounds (12 groups, 5 compounds each) and found to range from 4.2 × 10¹⁰ ( o-xylene) to 5.3 × 10¹⁶ M^-1 cm^-1 nm⁴ (a naphthalocyanine). The degree of overlap, defined by the ratio of the experimental J to the model J_G-0 for perfectly overlapped spectra, ranges from ∼0.5% (coumarin 151) to 77% (bacteriochlorophyll a). The results provide insights into how a variety of factors affect the resulting J values. The high degree of spectral overlap for (bacterio)chlorophylls prompts brief conjecture concerning the relevance of energy transfer to the question "why chlorophyll".

Sensing with photoluminescent semiconductor quantum dots

Fluorescent sensors benefit from high signal-to-noise and multiple measurement modalities, enabling a multitude of applications and flexibility of design. Semiconductor nanocrystal quantum dots (QDs) are excellent fluorophores for sensors because of their extraordinary optical properties. They have high thermal and photochemical stability compared to organic dyes or fluorescent proteins and are extremely bright due to their large molar cross-sections. In contrast to organic dyes, QD emission profiles are symmetric, with relatively narrow bandwidths. In addition, the size tunability of their emission color, which is a result of quantum confinement, make QDs exceptional emitters with high color purity from the ultra-violet to near infrared wavelength range. The role of QDs in sensors ranges from simple fluorescent tags, as used in immunoassays, to intrinsic sensors that utilize the inherent photophysical response of QDs to fluctuations in temperature, electric field, or ion concentration. In more complex configurations, QDs and biomolecular recognition moieties like antibodies are combined with a third component to modulate the optical signal via energy transfer. QDs can act as donors, acceptors, or both in energy transfer-based sensors using Förster resonance energy transfer (FRET), nanometal surface energy transfer (NSET), or charge or electron transfer. The changes in both spectral response and photoluminescent lifetimes have been successfully harnessed to produce sensitive sensors and multiplexed devices. While technical challenges related to biofunctionalization and the high cost of laboratory-grade fluorimeters have thus far prevented broad implementation of QD-based sensing in clinical or commercial settings, improvements in bioconjugation methods and detection schemes, including using simple consumer devices like cell phone cameras, are lowering the barrier to broad use of more sensitive QD-based devices.

Intracellular targeted delivery of quantum dots with extraordinary performance enabled by a novel nanomaterial design

Quantum dots (QDs) have emerged as a major class of fluorescent probes with unique optical properties, but applying QDs for imaging specific intracellular entities in live cells has been hindered by the poor performance of targeted intracellular delivery of QDs due to various cellular transport barriers. We describe a novel QD nanoprobe design, which is termed a cosolvent-bare hydrophobic QD-biomolecule (cS-bQD-BM, or 'SDot' for short), combining a cosolvent, a bare hydrophobic nanoparticle surface, ultrasmall size and biomolecular function. SDots show extraordinary intracellular targeting performance with the nucleus as the model target, including near-perfect specificity, excellent efficiency and reproducibility, high-throughput ability, minimal toxicity, and ease of operation, as well as superb optical properties and colloidal stability. We introduce integrated single-particle tracking and pair-correlation function analysis of a spinning-disk confocal microscope platform (iSPT-pCF-SDCM) to study SDot's cellular transport. Endocytosed SDots can undergo a highly potent and noninvasive process of vesicle escape, yielding complete vesicle escape with no serious vesicle disruption. We exploit SDots' unprecedented ability to overcome cellular transport barriers to enhance drug and macromolecule delivery.

Ligands and media impact interactions between engineered nanomaterials and clay minerals

The exponential growth in technologies incorporating engineered nanomaterials (ENMs) requires plans to handle waste ENM disposal and accidental environmental release throughout the material life cycle. These scenarios motivate efforts to quantify and model ENM interactions with diverse background particles and solubilized chemical species in a variety of environmental systems. In this study, quantum dot (QD) nanoparticles and clay minerals were mixed in a range of water chemistries in order to develop simple assays to predict aggregation trends. CdSe QDs were used as a model ENM functionalized with either negatively charged or zwitterionic small molecule ligand coatings, while clays were chosen as an environmentally relevant sorbent given their potential as an economical water treatment technology and ubiquitous presence in nature. In our unbuffered experimental systems, clay type impacted pH, which resulted in a change in zwitterionic ligand speciation that favored aggregation with kaolinite more than with montmorillonite. With kaolinite, the zwitterionic ligand-coated QD exhibited greater than ten times the relative attachment efficiency for QD-clay heteroaggregation compared to the negatively charged ligand coated QD. Under some conditions, particle oxidative dissolution and dynamic sorption of ions and QDs to surfaces complicated the interpretation of the removal kinetics. This work demonstrates that QDs stabilized by small molecule ligands and electrostatic surface charges are highly sensitive to changes in water chemistry in complex media. Natural environments enable rapid dynamic physicochemical changes that will influence the fate and mobility of ENMs, as seen by the differential adsorption of water-soluble QDs to our clay media.