Magnetic nanocellulose-based adsorbent for highly selective removal of malachite green from mixed dye solution

Herein, a novel magnetic adsorbent (BC/AA/MN@Fe3O4) was successfully prepared from waste bamboo fiber tissue and montmorillonite, and subsequently applied for the highly selective removal of malachite green (MG, removal efficiency = 97.3 %) from the mixed dye solution of MG with methyl orange (MO, removal efficiency = 4.5 %). The magnetic adsorbent has a high porosity with abundant mesopores. In the single dye MG solution, the adsorbent could effectively remove MG over a wide pH range from 4 to 10, and the maximum adsorption capacity (qmax) was 2282.3 mg/g. Moreover, the magnetic adsorbent could remove MG from various solutions including mixed dye solution, high salinity solution, and real river water dye solution. The thermodynamic results proved that the adsorption process of MG was spontaneous and endothermic. The adsorption of MG was due to the comprehensive effects of electrostatic attraction, hydrogen bonding interactions and ions exchange, between the adsorbent and MG. Furthermore, the BC/AA/MN@Fe3O4 exhibited an excellent reusability with adsorption efficiency above 53.4 % after five consecutive cycles. Therefore, the prepared magnetic nanocellulose-based adsorbent was expected to be a promising material for highly selective adsorption and separation of MG from mixed dye solution.

Removal of cationic dye pollutants from wastewater with HS loaded semi-IPN composites: kinetic and thermodynamic studies

In this study, methylene blue (MB) pollutant in water was removed using produced hazelnut shell loaded semi-interpenetrating polymer networks (HS loaded semi-IPN) adsorbent. The physical and chemical characterizations of the adsorbents were investigated using TGA, DSC, FT-IR, BET, FE-SEM, and EDX. Experimental parameters such as temperature, swelling, dye concentration, contact time, pH solution, and adsorbent dosage for MB adsorption were thoroughly investigated. It was determined that the HS loaded semi-IPN adsorbent removed 92.1% of MB dye. Subsequently, the adsorption properties between the adsorbent and dye were investigated in detail using several different kinetic, isotherm, and thermodynamic models. As a result of the obtained data, the interaction between adsorbent and dye molecules is discussed. Moreover, studies on the industrial usability of the adsorbent have been carried out, and it has been observed that the adsorbent can be employed even after four cycles.

Banana Peel Derived Chitosan-Grafted Biocomposite for Recovery of NH4+ and PO43

Biomass-derived adsorbents afford accessible and inexpensive harvesting of nitrogen and phosphorus from wastewater sources. Human urine is widely accepted as a rich source of nitrogen and phosphorus. However, direct use of urine in agriculture is untenable because of its unpleasant smell, pathogen contamination, and pharmaceutical residues. In this work, we have grafted chitosan onto dried and crushed banana peel (DCBP) to generate the biocomposite DCBP/Ch. A combination of FTIR, TGA, XRD, FESEM, EDX, and NMR analyses were used to characterize DCBP/Ch and reveal condensation-aided covalent conjugation between O-H functionalities of DCBP and chitosan. The adsorption performance of DCBP/Ch toward NH4+ and PO43- is in sync with its attractive surface porosity, elevated crystallinity, and thermostability. The maximum adsorption capacity of DCBP/Ch toward NH4+/PO43- was estimated as 42.16/15.91 mg g-1 at an operating pH of 7/4, respectively, and ranks highly when compared to previously reported bioadsorbents. DCBP/Ch performs admirably when tested on artificial urine. While nitrogen and phosphorus harvesting from human urine using single techniques has been reported previously, this is the first report of a single adsorbent for recovery of NH4+ and PO43-. The environmental compatibility, ease of preparation, and economic viability of DCBP/Ch present it as an attractive candidate for deployment in waste channels.

An MXene-Grafted Terpolymer Hydrogel for Adsorptive Immobilization of Toxic Pb(II) and Post-Adsorption Application of Metal Ion Hydrogel

Toxic metal ions present in industrial waste, such as Pb(II), introduce deleterious effects on the environment. Though the adsorptive removal of Pb(II) is widely reported, there is a dearth of research on the suitable utilization and disposal of the Pb(II)-adsorbed adsorbent. In this work, an MXene-grafted terpolymer (MXTP) hydrogel has been designed for the adsorption of Pb(II) under ambient conditions of pH and temperature. The hydrogel MXTP was synthesized by facile one-pot polymerization in aqueous solvent, and the detailed structural characterization of terpolymer (TP), MXTP, and Pb(II)-loaded MXTP, i.e., Pb(II)-MXTP, was carried out by a combination of proton nuclear magnetic resonance (1H NMR), Fourier-transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffractometric (XRD), thermogravimetric/differential thermogravimetric (TG/ DTG), and field emission scanning electron microscopic (FESEM) analyses. The specific capacitance and conductivities of Pb(II)-MXTP were studied with cyclic voltammetry (CV) and electrical impedance spectroscopy (EIS), which unambiguously indicate successful post-adsorption application. The specific capacitance of MXTP decreased after Pb(II) adsorption, whereas the conductivity increased significantly after Pb(II) adsorption, showing that MXTP can be successfully deployed as a solid electrolyte/anode after Pb(II) adsorption. This study covers the synthesis of a novel MXene-grafted terpolymer hydrogel for adsorptive exclusion of Pb(II) and assessment of the as-adsorbed Pb(II)-loaded hydrogel as a solid electrolyte/anode material and is the first demonstration of such post-adsorptive application.

Advances in gum-based hydrogels and their environmental applications

Gum-based hydrogels (GBHs) have been widely employed in diverse water purification processes due to their environmental properties, and high absorption capacity. More desired properties of GBHs such as biodegradability, biocompatibility, material cost, simplicity of manufacture, and wide range of uses have converted them into promising materials in water treatment processes. In this review, we explored the application of GBHs to remove pollutants from contaminated waters. Water resources are constantly being contaminated by a variety of harmful effluents such as heavy metals, dyes, and other dangerous substances. A practical way to remove chemical waste from water as a vital component is surface adsorption. Currently, hydrogels, three-dimensional polymeric networks, are quite popular for adsorption. They have more extensive uses in several industries, including biomedicine, water purification, agriculture, sanitary products, and biosensors. This review will help the researcher to understand the research gaps and drawbacks in this field, which will lead to further developments in the future.

Production of novel hazelnut shell-based semi-IPN biocomposite absorbents and their use in removing heavy metal ions from water

In this study, a hazelnut shell (HS) filled semi-interpenetrating polymer networks (semi-IPN) biocomposite adsorbent with novel and different compositions was developed that will enable the removal of lead ions, which are commonly found in water, by adsorption reactions. The structural and morphological properties of the produced adsorbents were characterized by FT-IR, XRD, TGA, DSC, BET, FE-SEM, EDX, and zeta potential measurements, and the production mechanism of these adsorbents was discussed. The effects of parameters such as different adsorbent dosages, different heavy metal concentrations, type of adsorbent, contact time, pH, and temperature on the swelling abilities and adsorption properties of adsorbents were investigated in detail. It has been determined that the adsorbent, which exhibits optimum adsorption and swelling properties, is a biocomposite containing 5% by weight HS filler, and it has been observed that it can remove up to 85% of lead ions under different parameters and conditions. In addition, the adsorption behaviors of the produced biocomposites are discussed using isothermal, kinetic, and thermodynamic models. Moreover, studies have been carried out on the reusability of the adsorbent, and it has been observed that the adsorbent produced within the scope of the study is still usable even after four cycles.

Interpenetrating polymer networks for desalination and water remediation: a comprehensive review of research trends and prospects

Interpenetrating polymer network (IPN) architectures have gained a lot of interest in recent decades, mainly due to their wide range of applications including water treatment and environmental remediation. IPNs are composed of two or more crosslinked polymeric matrices that are physically entangled but not chemically connected. In polymer science, the interpenetrating network structure with its high polymer chain entanglement is commonly used to generate materials with many functional properties, such as mechanical robustness and adaptable structure. In order to remove a targeted pollutant from contaminated water, it is feasible to modify the network architectures to increase the selectivity by choosing the monomer appropriately. This review aims to give a critical overview of the recent design concepts of IPNs and their applications in desalination and water treatment and their future prospects. This article also discusses the inclusion of inorganic nanoparticles into traditional polymeric membrane networks and its advantages. In the first part, the current scenario for desalination, water pollution and conventional desalination technologies along with their challenges is discussed. Subsequently, the main strategies for the synthesis of semi-IPNs and full-IPNs, and their relevant properties in water remediation are presented based on the nature of the networks and mechanism, with an emphasis on the IPN membrane. This review article has thoroughly investigated and critically assessed published works that describe the latest study on developing IPN membranes, hydrogels and composite materials in water purification and desalination. The goal of this critical analysis is to elicit fresh perspectives regarding the application and advantages of IPNs in desalination and water treatment. This article will also provide a glimpse into future areas of research to address the challenges relating to advanced water treatment as well as its emerging sustainable approaches. The study has put forward a convincing justification and establishes the relevance of IPNs being one of the most intriguing and important areas for achieving a sustainable generation of advanced materials that could benefit mankind.

A pH responsive and superporous biocomposite hydrogel of Salvia spinosa polysaccharide-co-methacrylic acid for intelligent drug delivery

Herein, a drug delivery system (SSH-co-MAA) based on the mucilage from seeds of Salvia spinosa (SSH; polymer) and methacrylic acid (MAA; monomer) is introduced for the controlled delivery of venlafaxine HCl using a sustainable chemical approach. The optimized conditions for the designing of the ideal formulation (M4) of SSH-co-MAA were found to be 2.5% (w/w) of SSH, 30.0% (w/w) of MAA, 0.4% (w/w) of both N,N'-methylene-bis-acrylamide (MBA; cross-linker) and potassium persulfate (KPS; initiator). The structure characterization of SSH-co-MAA by Fourier transform infrared and solid-state CP/MAS ¹³C-NMR spectroscopy has confirmed the grafting of MAA onto SSH. The thermogravimetric analysis revealed that SSH-co-MAA is a stable entity before and after loading of the venlafaxine HCl-loaded SSH-co-MAA (VSSH-co-MAA). Scanning electron microscopy images of SSH-co-MAA after swelling then freeze drying showed the superporous nature of the hydrogel. The gel fraction (%) of SSH-co-MAA depended upon concentration of SSH, MAA, and MBA. The porosity (%) was increased with the increase in the concentration of SSH and decreased with the decrease in the concentration of MAA and MBA. The swelling indices, venlafaxine HCl loading, and release (24 h at the pH of the gastrointestinal tract) from VSSH-co-MAA were found to be dependent on the pH of the swelling media and the concentration of SSH, MAA, and MBA. The release of venlafaxine HCl followed non-Fickian diffusion mechanism. Conclusively, SSH-co-MAA is a novel material for potential application in targeted drug delivery applications.

On the Sorbent Ability and Reusability of Graphene-Oxide-Chitosan Aerogels for the Removal of Dyes from Wastewater

One of the most persistent issues affecting people worldwide is water contamination due to the indiscriminate disposal of pollutants, causing severe environmental problems. Dyes are among the most harmful contaminants because of their high chemical stability and consequently difficult degradation. To remove contaminants from water, adsorption is the most widely used and effective method. In this work, we recall the results already published about the synthesis, the characterization and the use of porous graphene-oxide-chitosan aerogels as a sorbent material. Those systems, prepared by mixing GO sheets and CS chains, using APS as a cross-linking agent, and by further lyophilization, were further characterized using nano-computed tomography, supplying more understanding about their micro and nano-structure. Their sorbent ability has been investigated also by the study of their isotherm of adsorption of two different anionic dyes: Indigo Carmine and Cibacron Brilliant Yellow. Those analyses confirmed the potentialities of the aerogels and their affinity for those anionic dyes. Moreover, the possibility of regenerating and reusing the material was evaluated as a key aspect for applications of this kind. The treatment with NaOH, to promote the desorption of adsorbed dyes, and subsequent washing with HCl, to re-protonate the system, ensured the regeneration of the gels and their use in multiple cycles of adsorption with the selected water contaminants.

Bamboo Nanocellulose/Montmorillonite Nanosheets/Polyethyleneimine Gel Adsorbent for Methylene Blue and Cu(II) Removal from Aqueous Solutions

In recent years, the scarcity of pure water resources has received a lot of attention from society because of the increasing amount of pollution from industrial waste. It is very important to use low-cost adsorbents with high-adsorption performance to reduce water pollution. In this work, a gel adsorbent with a high-adsorption performance on methylene blue (MB) and Cu(II) was prepared from bamboo nanocellulose (BCNF) (derived from waste bamboo paper) and montmorillonite nanosheet (MMTNS) cross-linked by polyethyleneimine (PEI). The resulting gel adsorbent was characterized by Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (SEM), X-ray photoelectron spectroscopic (XPS), etc. The results indicated that the MB and Cu(II) adsorption capacities of the resulting gel adsorbent increased with the solution pH, contact time, initial concentration, and temperature before equilibrium. The adsorption processes of MB and Cu(II) fitted well with the fractal-like pseudo-second-order model. The maximal adsorption capacities on MB and Cu(II) calculated by the Sips model were 361.9 and 254.6 mg/g, respectively. The removal of MB and Cu(II) from aqueous solutions mainly included electrostatic attraction, ion exchange, hydrogen bonding interaction, etc. These results suggest that the resulting gel adsorbent is an ideal material for the removal of MB and Cu(II) from aqueous solutions.

Interpenetrating polymeric network (IPNs) in ophthalmic drug delivery: Breaking the barriers

To maintain the therapeutic drug concentration for a prolonged period of time in aqueous and vitreous humor is primary challenge for ophthalmic drug delivery. Majority of the locally administered drug into the eye is lost as to natural reflexes like blinking and lacrimation resulting in the short span of drug residence. Consequently, less than 5% of the applied drug penetrate through the cornea and reaches the intraocular tissues. The major targets for optimal ophthalmic drug delivery are increasing drug residence time in cul-de-sac of the eye, prolonging intraocular exposure, modulating drug release from the delivery system, and minimizing pre-corneal drug loss. Development of in situ gel, contact lens, intraocular lens, inserts, artificial cornea, scaffold, etc., for ophthalmic drug delivery are few approaches to achieve these major targeted objectives for delivering the drug optimally. Interpenetrating polymeric network (IPN) or smart hydrogels or stimuli sensitive hydrogels are the class of polymers that can help to achieve the targets in ophthalmic drug delivery due to their versatility, biocompatibility and biodegradability. These novel ''smart" materials can alter their molecular configuration and result in volume phase transition in response to environmental stimuli, such as temperature, pH, ionic strength, electric and magnetic field. Hydrogel and tissue interaction, mechanical/tensile properties, pore size and surface chemistry of IPNs can also be modulated for tuning the drug release kinetics. Stimuli sensitive IPNs has been widely exploited to prepare in situ gelling formulations for ophthalmic drug delivery. Low refractive index hydrogel biomaterials with high water content, soft tissue-like physical properties, wettability, oxygen, glucose permeability and desired biocompatibility makes IPNs versatile candidate for contact lenses and corneal implants. This review article focuses on the exploration of these smart polymeric networks/IPNs for therapeutically improved ophthalmic drug delivery that has unfastened novel arenas in ophthalmic drug delivery.

Mechanistic evaluation of metformin drug confiscation from liquid phase on itaconic acid/kaolin hydrogel nanocomposite

Herein, kaolin (K) was amended by a novel gemini surfactant to attain nano-kaolin (nK), which was subsequently employed as a cross-linker in the preparation of itaconic acid/kaolin hydrogel nanocomposite (IA/nK) via free radical polymerization route employing the sonochemical technique, which has been used for the first time to extract metformin (MF) from water solution. The aspects which affect sorption behavior of IA/nK on metformin (MF) were systematically investigated via batch experiments, in harmony with effect of sorbent dosage, contact time, pH, MF concentration, equilibrium curves, kinetic behavior, and thermodynamic parameters. BET studies of IA/nK exhibited S_BET of 106.42 m²g^-1, pore volume 0.281 cm³ g^-1, and a pore radius of 16.627 Å. Kinetic and isotherm modelling portrayed that pseudo-second order and Freundlich model appropriated adsorption data with maximum sorption capacity of 278.35 mg g^-1. Thermodynamic parameters ΔH^O (13.67 kJmol^-1) and ΔG^O (-7.648 kJmol^-1) revealed that sequestration of MF on IA/nK was endothermic, spontaneous, and dominated by physisorption. Molecular docking study along with X-ray photoelectron spectroscopy inferred electrostatic interaction and hydrogen bonding as main mechanism of MF removal. IA/nK demonstrated dose-reliant inhibition of both gram-positive and gram-negative bacterial strains. IA/nK demonstrated good regeneration properties, up to four cycles without considerable decrease in its efficacy. The admirable sorption capacity coupled with good reusability, and low toxicity substantiates IA/nK as promising adsorbent for MF confiscation.

One-pot synthesis of sodium alginate-grafted-terpolymer hydrogel for As(III) and V(V) removal: In situ anchored comonomer and DFT studies on structures

In this work, an optimum sodium alginate (NaAlg)-grafted-[sodium 2-methylenesuccinate-co-sodium 2-((2-(isobutyryloxy)ethoxy)methyl)succinate-co-ethylene glycol methacrylate, i.e., SMS-co-SIBEMS-co-EGMA, i.e., P1], i.e., P2, was selected among twelve hydrogels synthesized by employing variable amounts of synthesis parameters through a facile polymerization of SMS and EGMA monomers. In P1 and P2, SIBEMS third comonomer was strategically anchored in situ. The formation of terpolymer, i.e., P1, rather than generally expected copolymer, i.e., SMS-co-EGMA/ CoP1, was explored via closeness of experimental and simulated excitation energies of P1 and CoP1, measured by using density functional theory (DFT). The grafting of NaAlg into synthetic P1 elevated swelling, crosslink density (CD), network stability, reusability, and adsorption capacity (AC) of semisynthetic hydrogel, i.e., P2. The reusable P2 presenting optimum result among swelling, CD, and mean molar mass was chosen selectively for removals of As(III) and V(V). The structures of P1, P2, and adsorbed P2, i.e., As(III)-P2 and V(V)-P2; NaAlg-grafting; in situ anchored SIBEMS comonomer; reusability; thermostability; and surface properties were explored through XPS-NMR-FTIR-UV-vis, DFT, TG, DLS, XRD, SEM, pH_PZC, and network and thermodynamic energies. The ACs of 0.025 g P2 for As(III) and V(V) were 112.24 and 88.89 mg g^-1, respectively, at 308 K and within 5-100 mg L^-1. The ACs reduced to 67.26, 75.49, 71.42, and 98.25 mg g^-1 for As(III) and 40.25, 50.49, 45.37, and 67.88 mg g^-1 for V(V) in the presence of Mn(II), Cu(II), Ni(II), and Zn(II), respectively.

Synthesis of pH-sensitive crosslinked guar gum-g-poly(acrylic acid-co-acrylonitrile) for the delivery of thymoquinone against inflammation

The present work aims to synthesize the pH-sensitive crosslinked guar gum-g-poly(acrylic acid-co-acrylonitrile) [guar-g-(AA-co-ACN)] via microwave-assisted technique for the sustained release of thymoquinone. The synthesized material [guar-g-(AA-co-ACN)] was optimized by varying synthetic parameters viz. monomer concentration, reaction time, and microwave power to obtain the maximum yield of the crosslinked guar gum grafted product as well as maximum encapsulation of thymoquinone. The synthesized material [guar-g-poly(AA-co-ACN)] was characterized by FT-IR, SEM, XRD, NMR, zeta potential, and thermal techniques. This synthesized material was used to encapsulate thymoquinone (TQ) for effective nanotherapeutic delivery. In-vitro thymoquinone release behavior of guar-g-poly(AA-co-ACN) based nanoparticles (NpTGG) was investigated. The maximum thymoquinone release (78%) was achieved at pH 7.4 and time (6 h). The NpTGG also exhibited better antioxidant activity and hemocompatibility as compared to thymoquinone. Cytotoxicity of uar-g-(AA-co-ACN) and NpTGG was also evaluated against the human kidney VERO cell line and found to be nontoxic. Current research provides a cost-effective and green approach for the synthesis of guar-g-(AA-co-ACN) and NpTGG for sustained release of thymoquinone.

Phosphorylation of Guar Gum/Magnetite/Chitosan Nanocomposites for Uranium (VI) Sorption and Antibacterial Applications

The development of new materials is needed to address the environmental challenges of wastewater treatment. The phosphorylation of guar gum combined with its association to chitosan allows preparing an efficient sorbent for the removal of U(VI) from slightly acidic solutions. The incorporation of magnetite nanoparticles enhances solid/liquid. Functional groups are characterized by FTIR spectroscopy while textural properties are qualified by N2 adsorption. The optimum pH is close to 4 (deprotonation of amine and phosphonate groups). Uptake kinetics are fast (60 min of contact), fitted by a pseudo-first order rate equation. Maximum sorption capacities are close to 1.28 and 1.16 mmol U g-1 (non-magnetic and magnetic, respectively), while the sorption isotherms are fitted by Langmuir equation. Uranyl desorption (using 0.2 M HCl solutions) is achieved within 20-30 min; the sorbents can be recycled for at least five cycles (5-6% loss in sorption performance, complete desorption). In multi-component solutions, the sorbents show marked preference for U(VI) and Nd(III) over alkali-earth metals and Si(IV). The zone of exclusion method shows that magnetic sorbent has antibacterial effects against both Gram+ and Gram- bacteria, contrary to non-magnetic material (only Gram+ bacteria). The magnetic composite is highly promising as antimicrobial support and for recovery of valuable metals.

Eco-Friendly and Economic, Adsorptive Removal of Cationic and Anionic Dyes by Bio-Based Karaya Gum-Chitosan Sponge

A novel, lightweight (8 mg/cm³), conjugate sponge of karaya gum (Kg) and chitosan (Ch) has been synthesized with very high porosity (~98%) and chemical stability, as a pH-responsive adsorbent material for the removal of anionic and cationic dyes from aqueous solutions. Experimental results showed that Kg-Ch conjugate sponge has good adsorption capacity for anionic dye methyl orange (MO: 32.81 mg/g) and cationic dye methylene blue (MB: 32.62 mg/g). The optimized Kg:Ch composition grants access to the free and pH-dependent ionizable functional groups on the surface of the sponge for the adsorption of dyes. The studies on the adsorption process as a function of pH, adsorbate concentration, adsorbent dose, and contact time indicated that the adsorption capacity of MB was decreased with increasing pH from 5 to 10 and external mass transfer together with intra-particle diffusion. The adsorption isotherm of the anionic dye MO was found to correlate with the Langmuir model (R² = 0.99) while the adsorption of the cationic MB onto the sponge was better described by the Freundlich model (R² = 0.99). Kinetic regression results specified that the adsorption kinetics were well represented by the pseudo-second-order model. The H-bonding, as well as electrostatic interaction between the polymers and the adsorption interactions of dyes onto Kg-Ch sponge from aqueous solutions, were investigated using attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy, and the highly wrinkled porous morphology was visualized in depth by field-emission scanning electron microscopy (FE-SEM) analysis. Moreover, the samples could be reused without loss of contaminant removal capacity over six successive adsorption-desorption cycles. The hierarchical three-dimensional sponge-like structure of Kg has not been reported yet and this novel Kg-Ch sponge functions as a promising candidate for the uninterrupted application of organic pollutant removal from water.

Fabrication and Characterization of Polysaccharide Metallohydrogel Obtained from Succinoglycan and Trivalent Chromium

In the present study, a polysaccharide metallohydrogel was successfully fabricated using succinoglycan and trivalent chromium and was verified via Fourier transform infrared spectroscopy, differential scanning calorimetry analysis, thermogravimetric analysis (TGA), field emission scanning electron microscopy, and rheological measurements. Thermal behavior analysis via TGA indicated that the final mass loss of pure succinoglycan was 87.8% although it was reduced to 65.8% by forming a hydrogel with trivalent chromium cations. Moreover, succinoglycan-based metallohydrogels exhibited improved mechanical properties based on the added concentration of Cr³⁺ and displayed a 10 times higher compressive stress and enhanced storage modulus (G′) of 230% at the same strain. In addition, the pore size of the obtained SCx could be adjusted by changing the concentration of Cr³⁺. Gelation can also be adjusted based on the initial pH of the metallohydrogel formulation. This was attributed to crosslinking between chromium trivalent ions and hydroxyl/carboxyl groups of succinoglycan, each of which exhibits a specific pH-dependent behavior in aqueous solutions. It could be used as a soft sensor to detect Cr³⁺ in certain biological systems, or as a soft matrix for bioseparation that allows control of pore size and mechanical strength by tuning the Cr³⁺ concentration.

Nonconjugated Biocompatible Macromolecular Luminogens for Sensing and Removals of Fe(III) and Cu(II): DFT Studies on Selective Coordination(s) and On-Off Sensing

This work reports the design and synthesis of two nonaromatic biocompatible macromolecular luminogens, i.e., 2-(dimethylamino)ethyl methacrylate-co-2-(dimethylamino)ethyl 3-(N-(methylol)acrylamido)-2-methylpropanoate-co-N-(methylol)acrylamide/DMAEMA-co-DMAENMAMP-co-NMA (P1) and methacrylic acid-co-3-(N-(methylol)acrylamido)-2-methylpropanoic acid-co-N-(methylol)acrylamide/MEA-co-NMAMPA-co-NMA (P2), prepared through in situ anchored acrylamido-ester/DMAENMAMP and acrylamido-acid/NMAMPA third comonomers, respectively, in a facile polymerization of two non-luminous monomers in water medium to circumvent the drawbacks related to aggregation-caused quenching of aromatic luminogens. The structures of P1/P2, in situ anchored comonomers, fluorophores, N-branching associated n-π* interactions, and hydrogen bonding assisted aggregation-enhanced emissions are comprehended by nuclear magnetic resonance, Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), ultraviolet-visible, thermogravimetric analysis (TGA), dynamic light scattering (DLS), transmission electron microscopy (TEM), fluorescence lifetime, and fluorescence imaging. P1 and P2 are appropriate for sensitive detections/exclusions of Fe(III)/Cu(II) and cell-imaging. The intrinsic fluorescence, on-off sensing, selective coordinations of Fe(III) and Cu(II) with fluorophores, emission quenching mechanisms, and removals of Fe(III) and Cu(II) are investigated by DFT/NTO analyses of P1/P2 and Fe(III)-P1 and Cu(II)-P2 complexes, XPS, and isotherms and kinetics parameters. The excellent biocompatibilities, comparable limit of detections, i.e., 1.70 × 10^-7 and 1.59 × 10^-7 [m], and higher adsorption capacities, i.e., 77.25 and 154.13 mg g^-1 , at low ppm; 303 K; and pH = 7 compel P1/P2 to be acceptable for multipurpose applications.

Synthesis of a novel arginine-modified starch resin and its adsorption of dye wastewater

In this work, corn starch (St) was firstly grafted with polyacrylamide (PAM) to obtain StAM, which was subsequently immobilized with arginine to obtain a guanidine-containing starch-based resin, StAM–Arg. The synthesized products were characterized via Fourier transform infrared spectroscopy (FT-IR), ¹³C-NMR nuclear magnetic resonance (¹³C-NMR), scanning electron microscopy (SEM), X-ray diffraction (XRD), gel permeation chromatography (GPC), X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA). StAM–Arg exhibited a significantly enhanced adsorption capacity for acid fuchsin (AF), acid orange G (AOG), and acid blue 80 (AB80) compared with zeolite, diatomite, St and StAM, and it also exhibited broad-spectrum adsorption for different dyes. Weak acidic conditions were favorable for the resin to adsorb acid dyes. The decolorization rate (DR) by StAM–Arg for mixed wastewater reached 82.49%, which was higher than that of activated carbon (DR = 58.09%). StAM–Arg showed high resistance to microbial degradation, resulting in significantly improved structural stability for the resin. Its antibacterial rate (AR) for E. coli was up to 99.73%. After 7 days in simulated natural water, the weight loss ratio (WR) of StAM–Arg was 14.5%, which was much lower than that of St (WR = 66.53%). The introduced guanidine groups were considered to be the major reason for the observed improvements. Furthermore, the cationic guanidine could trap the acid dyes via ion-exchange reactions, while effectively inhibiting or eliminating the growth of bacteria on the adsorbent surface. The above advantages, including good dyestuff adsorption properties, high structural stability and prolonged service life, make StAM–Arg overcome the inherent drawbacks of the existing natural polymer adsorbents and have good application prospect in the treatment of textile wastewater.

In the side reaction, the two aldehyde groups in the glutaraldehyde molecules should undergo an aldol condensation reaction with the hydroxyl group in the starch molecule, which has been corrected.

Fabrication of Hydrogels via Host-Guest Polymers as Highly Efficient Organic Dye Adsorbents for Wastewater Treatment

New self-assembled hydrogel materials of poly(vinyl alcohol)/cyclodextrin-modified poly(acrylic acid)/azobenzene-modified poly(acrylic acid) (PVA/PAA-CD/PAA-Azo) were successfully prepared via host-guest interactions and hydrogen bonds. The as-prepared hydrogel materials were characterized by various techniques, including Fourier transform infrared spectroscopy, X-ray diffraction analysis, scanning electron microscopy, ultraviolet spectroscopy, and specific surface area tests. The prepared hydrogels with different concentrations of PVA exhibited different network structures. In addition, ultraviolet (UV) light irradiation and temperature change induce a gel-sol phase transition in the hydrogel materials. The obtained hydrogel materials could be used as good adsorbents for two model organic dye molecules, which was mainly due to electrostatic interactions between methylene blue/rhodamine B (MB/RhB) and the gels in the adsorption process. In particular, the adsorption processes of the as-prepared hydrogel materials conformed to the pseudo-first-order model with a high correlation coefficient, which indicates that gel has a potential application in the field of wastewater purification.

Light-Emitting Multifunctional Maleic Acid-co-2-(N-(hydroxymethyl)acrylamido)succinic Acid-co-N-(hydroxymethyl)acrylamide for Fe(III) Sensing, Removal, and Cell Imaging

The intrinsically fluorescent highly hydrophilic multifunctional aliphatic terpolymer, maleic acid (MA)-co-2-(N-(hydroxymethyl)acrylamido)succinic acid (NHASA)-co-N-(hydroxymethyl)acrylamide (NHMA), that is, 1, was designed and synthesized via C-C/N-C-coupled in situ allocation of a fluorophore monomer, that is, NHASA, composed of amido and carboxylic acid functionalities in the polymerization of two nonemissive MA and NHMA. The scalable and reusable intrinsically fluorescent biocompatible 1 was suitable for sensing and high-performance adsorptive exclusion of Fe(III), along with the imaging of Madin-Darby canine kidney cells. The structure of 1, in situ fluorophore monomer, aggregation-induced enhanced emission, cell-imaging ability, and superadsorption mechanism were studied via microstructural analyses using 1H/13C NMR, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, atomic absorption spectroscopy, ultraviolet-visible spectroscopy, thermogravimetric analysis, dynamic light scattering, high-resolution transmission electron microscopy, solid-state fluorescence, fluorescence lifetime, and fluorescence imaging, along with measuring kinetics, isotherms, and thermodynamic parameters. The location, electronic structures, and geometries of the fluorophore and absorption and emission properties of 1 were investigated using density functional theory and natural transition orbital analyses. The limit of detection and the maximum adsorption capacity were 2.45 × 10-7 M and 542.81 mg g-1, respectively.

An elastic semi IPN polymer hybrid for enhanced adsorption of heavy metals

An elastic semi IPN from guar gum (GG), xanthan gum (XG) and poly(acrylic acid) (PAA) was developed and used as a bioadsorbent for soluble Pb(II) and Hg(II) from water. The IPNs were developed using a photo-initiated crosslinking cum polymerization approach (benzophenone was used as an initiator) with a variable composition of the biopolymers (GG:XG fixed at 20:80 by mass) to PAA by mass (Biopolymers: PAA as 90:10, 80:20, 70:30 and 50:50, respectively). The hybrids were extensively characterized for microstructure, morphology, swelling, porosity and rheological behavior, both in dry and swelled conditions. Three grades of biosorbents namely 90:10, 80:20 and 70:30 showed an enhanced adsorption efficiency compared to the remaining ternary grades as well as the crosslinked binary grade of GG:XG (20:80 mass composition, used as a control), respectively. It was primarily due to high network strength (elasticity) cum flexibility (more liquid like behavior) of those three ternary grades under swollen condition followed by their higher swelling capacity and strongly negative zeta potential to attract the positively charged Pb(II) and Hg(II), respectively. The 80:20 grade (80 parts was the mass composed of XG:GG in 80:20 mass ratio and 20 parts was the mass of PAA) exhibited the maximum molecular effect and thus recorded the highest adsorption efficiency (93 % for Pb(II) with an adsorption capacity of 111.6 and 72 % of Hg(II) with an adsorption capacity of 86.4). Nevertheless, all the hybrids showed a strong pH dependant adsorption as the -COOH unit present in the network displayed a pH sensitive ionization. The adsorption was lower below the pH level of 4.0 (pKa of PAA at 4.5) while drastically improved beyond that. On additional note, the adsorbate dose was also found to affect the adsorption efficiency whereby a maximum dose of 300 ppm of both Pb(II) and Hg(II) was found to be most effective for adsorption.

High-performance two-dimensional montmorillonite supported-poly(acrylamide-co-acrylic acid) hydrogel for dye removal

High-performance two-dimensional montmorillonite supported-poly (acrylamide-co-acrylic acid) hydrogel for dye removal was investigated. Montmorillonite cooperated with acrylamide and acrylic acid via polymerization, hydrogen-bond, amidation and electrostatic interactions to form the three-dimensional reticular-structured hydrogel with the free entrance for macromolecules. Adsorption tests revealed that the efficient removal (97%) for methylene blue at high concentration (200 mg/L) could be achieved via a small dose of hydrogel (0.5 g/L) within a short time (20 min). The excellent adsorption performance was profited from the electronegative surface and fully exposed reaction sites of two-dimensional montmorillonite, which could save the treatment cost and promote the removal effect compared with the conventional adsorbents. The adsorption process of methylene blue onto hydrogel could be fitted by both the pseudo-first-order and pseudo-second-order kinetics models, and the adsorption isotherm corresponded to the Sips model. The mechanism analysis based on Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy measurements illustrated that the reaction between carboxyl groups and methylene blue molecules as well as the cation-exchange enabled the hydrogel performing extraordinary adsorption efficiency.

Facile design of a dextran derived polyurethane hydrogel and metallopolymer: a sustainable approach for elimination of organic dyes and reduction of nitrophenols

This work reports a sustainable approach for fabrication of a highly cost-effective and operation-convenient adsorbent derived from dextran and its valorization to a metallopolymer photocatalyst.

Chitosan-grafted tetrapolymer using two monomers: pH-responsive high-performance removals of Cu(II), Cd(II), Pb(II), dichromate, and biphosphate and analyses of adsorbed microstructures

For circumventing the cumbersome and expensive multifunctional and multipolymer adsorbents for high-performance removals of hazardous water-contaminant(s), chitosan-g-[2-acrylamido-2-methyl-1-propanoic acid (AMPS)-co-2-(3-acrylamidopropanamido)-2-methylpropane-1-sulfonic acid (APAMPS)-co-2-(N-(3-amino-3-oxopropyl)acrylamido)-2-methylpropane-1-sulfonic acid (NAOPAMPS)-co-acrylamide (AM)] (i.e., chitosan-g-tetrapolymer), a multifunctional scalable and reusable hydrogel, was synthesized by grafting of chitosan and in situ attachments of N-H functionalized NAOPAMPS and APAMPS hydrophilic acrylamido-monomers during free-radical solution-polymerization of the two ex situ added AMPS and AM monomers in water. The response surface methodology was employed to synthesize one hydrogel envisaging the optimum balance between swelling and stability for the superadsorption of Cu(II), Cd(II), Pb(II), Cr₂O₇^2-, and HPO₄^2-. The in situ attachments of NAOPAMPS and APAMPS, grafting of chitosan into tetrapolymer, structures and properties, pH-responsive abilities, superadsorption mechanism, and reusability were understood via in depth microstructural analyses of adsorbed and/or unadsorbed chitosan-g-tetrapolymer(s) through ¹H/¹³C NMR, FTIR, XPS, TGA, XRD, DLS, and pH_PZC. The maximum adsorption capacities of Cd(II), Cu(II), Pb(II), Cr₂O₇^2-, and HPO₄^2- were 1374.41, 1521.08, 1554.08, 47.76, and 32.76 mg g^-1, respectively.

Bentonite-Acrylamide Hydrogels Prepared by the Nonmixing Method: Characterization and Properties

A significant amount of research has been conducted on bentonite-acrylamide hydrogels. These gels are usually prepared by uniformly mixing bentonite with reactive monomers. Herein, a new preparation method of bentonite-acrylamide hydrogels has been proposed to cater to one novel application of bentonite-acrylamide hydrogels. In this method, bentonite-acrylamide hydrogel was obtained by pressing bentonite into a thin mud cake and extruding a mixed liquor of acrylamide, a cross-linking agent, an initiator, and water into the thin mud cake and then subjecting the system to water-bath curing. The effects of extrusion pressure, extrusion time, and acrylamide concentration on the tensile strength and elemental composition of bentonite-acrylamide hydrogel were investigated. The results show that the tensile strength of the bentonite-acrylamide hydrogel first increased and then tended to be stable with the further increase in extrusion pressure and extrusion time. As the concentration of acrylamide increased, the tensile strength of the bentonite-acrylamide hydrogel increased first and then decreased slightly. With the increase in extrusion pressure, extrusion time, and acrylamide concentration, the contents of C and N elements in the thin mud cake gradually increased and then tended to be stable, which reflects the state of the monomer entering the thin mud cake. In addition, the elemental composition of the bentonite-acrylamide hydrogel was analyzed via the scanning electron microscopy-energy dispersive X-ray spectrometry method, and it was found that the composition of the hydrogel was relatively uniform in the direction of mixed liquor extrusion.