Natural mineral colloids facilitated transport of EE2 in saturated porous media: Effects of humic acid and conjugate form

Steroid estrogens have posed significant ecological risks to aquatic organisms due to their potent endocrine-disrupting effects. The role of natural mineral colloids in facilitating the transport of hydrophobic organic pollutants in the environment has been confirmed, but the control mechanisms of colloids on 17α-Ethinylestradiol (EE2) migration in the subsurface environment are often still not well understood. This study combined the batch sorption equilibrium experiments and dynamic transport simulations to reveal the interface interactions and co-transport characteristics between illite colloids and EE2 at both macroscopic and microscopic levels. The existing form changes of EE2 and the influence of coexisting humic acid (HA) during transport in porous media were also specifically investigated. The batch experiments demonstrated that the primary mechanisms governing EE2 sorption onto illite colloids involved surface sorption and hydrogen bonding. The coexistence of HA could load onto the surface of illite colloids, thereby enhancing the colloidal sorption capacity for EE2. Transport experiments demonstrated that the migratory ability of EE2 in silty clay was limited, but illite colloids could significantly promote its penetration, with the peak penetration content (Ct/C0) increasing from 0.64 to 0.77. In the absence of HA, EE2 primarily transported in a dissolved form, accounting for 62.86% of the total concentrations. When HA concentrations were increased to 10 mg/L and 20 mg/L, the proportion of colloidal conjugate EE2 in the effluents reached 52.13% and 54.49%, respectively. The enhanced transport of EE2 by HA was primarily attributed to the improved migration ability of illite colloids and the increased proportion of illite-EE2 conjugate, resulting in a maximum Ct/C0 value of 0.94. The validity of these results was further confirmed by employing calculations based on the Derjaguin-Landau-Verwey-Overbeek and Colloidal Filtration Theory. This study provides new insights of understanding the transport of EE2 in subsurface environment.

Estrogen adsorption from an aqueous solution on the chitosan nanoparticles

In this research, chitosan nanoparticles as an efficient and reusable adsorbent with adsorption capacity of 5.79 mg/g, surface area of 62 m²/g and pH_pzc of 8.07 were applied to remove the ethinylestradiol (as a sample of estrogen) from an aqueous wastewater. The chitosan nanoparticles were characterized by SEM, XRD and FT-IR analyses. Four independent variables involving contact time, adsorbent dosage, pH, and initial concentration of estrogen were applied to design the experiments by Design Expert software (CCD under RSM). In fact, number of experiments was minimized and the operating conditions were optimized for the maximum estrogen removal. The results indicated that three independent variables (contact time, adsorbent dosage, and pH) increment increased the estrogen removal while the estrogen initial concentration enhancement decreased the removal due to the concentration polarization phenomenon. The optimum conditions for the estrogen removal (92.50 %) on the chitosan nanoparticles were found at contact time of 220 min, adsorbent dosage of 1.45 g/l, pH of 7.3 and estrogen initial concentration of 5.7 mg/l. Moreover, the Langmuir isotherm and pseudo-second order models could properly legitimize estrogen adsorption process on the chitosan nanoparticles.

The role of MnO2 crystal morphological scale and crystal structure in selective catalytic degradation of azo dye

MnO₂, as a representative manganese-based catalyst with many kinds of crystal forms, has been widely used to activate PMS. However, the role of morphological scale and crystal structures on the catalytic capability of MnO₂ still lacks further study. In this study, four different crystal forms of MnO₂ (α-MnO₂, β-MnO₂, γ-MnO₂, and δ-MnO₂) are succeeded in being fabricated via hydrothermal processes and evaluated by activating PMS for the removal of Reactive Yellow X-RG, typical azo dye. Experiment results indicate that α-MnO₂ with a one-dimensional structure exhibits the best catalytic performance among the four as-prepared MnO₂, which can be attributed to its broadest crystal interplanar distance (0.692), the highest portion of Mn (III)/Mn (IV) (4.194), and lowest value of average oxidation state AOS (2.696). Correlation analysis confirms that interplanar distance is the most relative factor with the catalytic activity of MnO₂ among the three studied factors (R² = 0.99715). Meanwhile, the morphological scale structure of α-MnO₂ can also account for its highest catalytic ability among the four as-prepared MnO₂, including its large specific area and advantageous one-dimensional nanostructure. Furthermore, according to the response surface methodology, when the dosage of PMS is 2.369 g/L, the dosage of α-MnO₂ is 0.991 g/L, and the initial dye concentration is 1025 mg/L, the maximum removal rate of Reactive Yellow X-RG is up to 97.38%.

Transport of functional group modified polystyrene nanoplastics in binary metal oxide saturated porous media

Metal oxides exist in porous media in the form of composite metal oxides, which can significantly affect the transport and transformation of pollutants in the soil environment. In this study, binary metal oxide porous media were prepared to explore the effects of solution chemistry, and the presence of binary metal oxides on the transport of functional group modified polystyrene nanoplastics (PSNPs) in saturated porous media. The results show that the existence of binary metal oxides significantly affects the migration ability of PSNPs in saturated porous media. The increase of ionic strength and the presence of multivalent cations affect the transport capacity of PSNPs in porous media. The types of binary metal oxides affect the migration of PSNPs in saturated porous media. The surface roughness and electrostatic interaction are important factors affecting the retention of PSNPs on the surface of binary metal oxide saturated porous media. The surface morphology has a more far-reaching impact. In addition, DLVO theory cannot fully explain the interaction between PSNPs and saturated porous media in the presence of Al3+. This study's results help provide some theoretical support for the migration of microplastics in the soil environment.

Removal effects and potential mechanisms of bisphenol A and 17α-ethynylestradiol by Biogenic Mn oxides generated by Bacillus sp. WH4

Endocrine disrupting compounds (EDCs), such as bisphenol A (BPA) and 17α-ethynylestradiol (EE2), have increasingly negative effects on human and wildlife health. In this study, the biogenic Mn oxides (BMOs) generated by Bacillus sp. WH4 were characterized, and the removal effects and reaction kinetics of BPA and EE2 by BMOs under different pH values, initial organic concentrations, and dosages of BMOs were discussed. The results showed that the formation of BMOs was extracellular process, and Mn(II) was oxidized to Mn(III) and Mn(IV) with 23.56% and 76.44%, respectively. The degradation processes of BPA and EE2 by BMOs followed first-order reaction kinetics, and the removal effect decreased with increasing initial BPA/EE2 concentrations and increased with increasing dosages of BMOs. However, the removal effect of BPA by BMOs decreased and then increased with increasing pH, while the removal effect of EE2 by BMOs decreased with increasing pH. Under optimal conditions, the removal efficiency of BPA and EE2 exceeded 98.2% and 94.3%, respectively. Additionally, this study showed that BMOs degraded BPA by coupling, oxidative condensation, substitution, and elimination reactions to obtain sixteen intermediate products and EE2 by substitution and elimination reactions to obtain seven intermediate products.

Silica-catalyzed ozonation of 17α -ethinyl-estradiol in aqueous media-to better understand the role of silica in soils

A promising route for thorough removal of 17α-ethinyl estradiol (EE2) from aqueous media was achieved through ozonation using mesoporous silicas such SBA-15, SBA-16, MCM-41 and MCM-48 as catalysts. Comparison with aluminosilicates along with Zeta potential and particle size measurements allowed demonstrating that EE2 interaction with silanols and hydrophobic -Si-O-Si- groups are essential requirements for the catalytic activity. Acid-base interactions, if any, should have minor contribution. EE2 hydroxylation appears to be an early step in the ozonation on all catalysts, but MCM-41 showed increased activity in phenolic ring cleavage. Confrontation of HPLC-UV and UV-Vis and HPLC-UV measurements revealed highest catalytic activity for MCM-41 and to a lesser extend of MCM-48 due to their higher specific surface area and weaker acid character. These results provide valuable findings for judiciously tailoring optimum [EE2-Silica:Water] interactions for thorough oxidative degradation of endocrine disrupting compounds (EDC).

Removal of 17α-ethinylestradiol and caffeine from wastewater by UASB-Fenton coupled system

In aquatic systems, some substances considered as endocrine disruptors have been detected, which can be due to their incomplete elimination in wastewater treatment plants (WWTPs) and inadequate disposal of pharmaceuticals. Among these contaminants are 17α-ethinylestradiol (EE2) and caffeine (CAF). Moreover, it has been reported that this kind of contaminants may provoke different adverse effects in many aquatic organisms. Because of that, in the present study, up-flow anaerobic sludge blanket reactors (UASB) coupled with the Fenton process was evaluated for EE2 and CAF removal spiked in wastewater samples. First, the best reaction conditions were established in each process. For UASB reactor, two hydraulic retention times (HRT 8 and 24 h) were evaluated, achieving the highest chemical organic demand (COD) removal (70 %) and drug elimination (84 %-86 %) with HRT 24 h. Subsequently, Fenton process was conducted at pH 3 with different levels of Fe²⁺ (0.05-0.5 mmol/L) and molar ratios Fe²⁺:H₂O₂ (1:1-1:10). Better results were obtained with 0.5 mmol Fe²⁺/L, and 1:10 ratio molar Fe²⁺:H₂O₂. Finally, UASB-Fenton coupled system allowed 80 % of COD decrease, almost complete removal of drugs and the toxicity of samples on Vibrio fischeri was reduced from 73 % to 30 %, demonstrating that this coupled system is a promising and efficient system for pharmaceutical compounds removal from wastewater.

A comparative study of persulfate activation by iron-modified diatomite and traditional processes for the treatment of 17α-ethinylestradiol in water

Emerging pollutants have been the subject of worldwide study because their continuous entry into the environment presents a risk to ecosystems and human health. Advanced oxidation processes show promise for eliminating or reducing the concentrations of emerging pollutants in water. This study aimed to investigate the treatment of aqueous systems containing the synthetic hormone 17α-ethinylestradiol. An innovative method for persulfate activation catalysed by iron-modified diatomite (heterogeneous system) was compared to conventional homogeneous activation methods (iron activation, alkaline activation, and heat activation). Iron-modified diatomite was more efficient in activating persulfate than traditional processes, achieving 98% of pollutant removal. Experimental results indicated that the catalyst can be reused without loss of removal efficiency, with potential environmental and economic benefits.

Seaweeds fast EDC bioremediation: Supporting evidence of EE2 and BPA degradation by the red seaweed Gracilaria sp., and a proposed model for the remedy of marine-borne phenol pollutants

In the last few decades, Endocrine Disrupting Chemicals (EDCs) have taken significant roles in creating harmful effects to aquatic organisms. Many proposed treatment applications are time consuming, expensive and focus mainly on waste water treatment plants (WWTP), which are indeed a major aquatic polluting source. Nonetheless, the marine environment is the ultimate sink of many pollutants, e.g. EDCs, and has been largely neglected mainly due to the challenge in treating such salty and immense open natural ecosystems. In this study we describe the bromination and the yet unpresented degradation process of high concentrations (5 mg/L) of phenolic EDCs, by the marine red macroalgaeGracilaria sp. As shown, 17α-Ethinylestradiol (EE2), a well-known contraceptive drug, and one of the most persistent phenol EDCs in the environment, was eliminated from both the medium and tissues of the macroalga, in addition to the degradation of all metabolites as verified by the nil estrogenic activity recorded in the medium. Validation of the proposed bromination-degradation route was reinforced by identifying Bisphenol A (BPA) brominated degradation products only, following 168H of incubation in the presence of Gracilaria sp. As demonstrated in this assay for EE2, BPA and finally for paracetamol, it is likely that the phenol scavenging activity is nonspecific and, thus, possibly even a wider scope of various other phenol-based pollutants might be treated in coastal waters. As far as we know, Gracilaria sp. is the only marine sessile organism able of degrading various phenol based pollutants. The worldwide distribution of many Gracilaria species and their wide aquaculture knowhow, suggest that bioremediation based on these seaweeds is a possible cost effective progressive solution to the treatment of a wide scope of phenols at the marine environment.

Synthesis a graphene-like magnetic biochar by potassium ferrate for 17β-estradiol removal: Effects of Al2O3 nanoparticles and microplastics

A graphene-like magnetic biochar (GLMB) was synthesized using lotus seedpod and potassium ferrate with simple step and applied for E2 adsorption. GLMB was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscope (AFM), X-ray photoelectron spectroscopy (XPS), Raman, X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and BET surface area. Several common (solution pH, ionic strength, humic acid and foreign ions) and new (Al₂O₃ nanoparticles and microplastics (MPs)) water experiment conditions were investigated. Characterization results demonstrated that the sample was fabricated successfully and it possessed some graphene-like properties and a large surface area (828.37 m²/g). Adsorption results revealed that the pseudo-second-order kinetics and Langmuir isotherm models could provide a better description for E2 uptake behavior. The E2 adsorption capacity could be influenced by solution pH, ionic strength and SO₄^2- ions, and the effect of humic acid and background electrolyte (Na⁺, K⁺, Ca²⁺, Mg²⁺, Cl^-, NO₃^-, PO₄^3-) could be neglected. The presences of Al₂O₃/MPs significantly decreased the time to reach adsorption equilibrium for E2 adsorption on GLMB, but had no obvious improvement or inhibiting effects on E2 removal when the adsorption reached equilibrium. The adsorption mechanism for E2 adsorption on GLMB was multiple, which involving π-π interactions, micropore filling effects, electrostatic interaction. The regeneration experiments showed that GLMB possessed a good regeneration performance. Based on the experimental results and comparative analysis with other adsorbents, GLMB was an economical, high-efficiency, green and recyclable adsorbent for E2 removal from aqueous solution.

The preparation of a novel iron/manganese binary oxide for the efficient removal of hexavalent chromium [Cr(vi)] from aqueous solutions

To remove hexavalent chromium Cr(vi) efficiently, a novel Fe–Mn binary oxide adsorbent was prepared via a “two-step method” combined with a co-precipitation method and hydrothermal method. The as-prepared Fe–Mn binary oxide absorbent was characterized via transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectra (FTIR), thermogravimetric analysis (TGA), zeta potential, BET and X-ray photoelectron spectroscopy (XPS). The results indicated that the morphology of the adsorbent was rod-like with length of about 100 nm and width of about 50–60 nm, specific surface area was 63.297 m² g⁻¹, has the composition of α-Fe₂O₃, β-MnO₂ and MnFe₂O₄ and isoelectric point was observed at pH value of 4.81. The removal of Cr(vi) was chosen as a model reaction to evaluate the adsorption capacity of the Fe–Mn binary oxide adsorbent, indicating that the Fe–Mn binary oxide adsorbent showed high adsorption performance (removal rate = 99%) and excellent adsorption stability (removal rate > 90% after six rounds of adsorption). The adsorption behavior of the Fe–Mn binary oxide was better represented by the Freundlich model (adsorption isotherm) and the pseudo-second-order model (adsorption kinetic), suggesting that the adsorption process was multi-molecular layer chemical adsorption. The possible adsorption mechanism of the Fe–Mn binary oxide for the removal of Cr(vi) included the protonation process and the electrostatic attraction interactions.

A novel Fe–Mn binary oxide adsorbent prepared via “co-precipitation and hydrothermal” method, for the efficient and fast removal of Cr(vi).

Adsorption studies of 17β-estradiol from aqueous solution using a novel stabilized Fe-Mn binary oxide nanocomposite

The removal of 17β-estradiol (E2) from contaminated water on nanoscale Fe-Mn binary oxide-loaded multiwalled carbon nanotubes (MWCNTs/FMBO) was evaluated in this work. The characterizations of the mesoporous adsorbent were analyzed by using SEM, TEM, VSM, XRD, XPS, and FTIR measurements. The effects of experimental conditions in E2 removal, including stabilizer additional level, adsorption time, initial E2 concentration, solution pH, reaction temperature, and foreign ions, were examined. The maximum monolayer adsorption capacity (q_m) of MWCNTs/FMBO for E2 in the experiment was 47.25 mg/g as verified by the Langmuir sorption isotherm study. The adsorption process was pH-sensitive with an optimum pH of 7.0. On the kinetics study, the adsorption data could be satisfactorily fitted by the pseudo-second-order kinetics. Thermodynamic parameters indicated that the adsorption process was spontaneous and exothermal. In addition, the foreign ions did not show any noticeable inhibition for E2 removal from the water solution except for PO₄^3- that was adversely affected for E2 uptake than other anions in a certain concentration. The adsorption capacities of the mesoporous adsorbent remained at 86.16% even after five adsorption-desorption cycles without significant loss of capacity, which demonstrated the stability and reusability for further removal of E2. Moreover, both hydrogen bond and π-π interaction might be the dominating adsorption mechanisms for E2 adsorption onto MWCNTs/FMBO.

Synergistic effects of biogenic manganese oxide and Mn(II)-oxidizing bacterium Pseudomonas putida strain MnB1 on the degradation of 17 α-ethinylestradiol

While biogenic manganese oxide (BMO) generated via the oxidation of Mn(II) by the Mn-oxidizing bacteria (MOB) have received attention, the relative roles of biological activity by MOB themselves were not clearly investigated. In this study, the synergistic effects of BMO and MOB Pseudomonas putida strain MnB1 on the degradation of 17α-ethinylestradiol (EE2) was investigated. Experiments with BMO in the presence of P. putida MnB1 showed 15-fold higher removal than that with BMO alone, suggesting that EE2 degradation was mediated by the biological activity of MOB as well as abiotic reaction by BMO. Trapping experiments with pyrophosphate (PP) proved that Mn(III) intermediate formed during the biological process from Mn (II) to Mn (IV) contribute much to the EE2 removal. Also, sharp decreases in EE2 removal were observed when microbial activity was inactivated by heat treatment or sodium azide. From this study, the EE2 removal mechanisms by BMO in the presence P. putida MnB1 are described as follows: (1) abiotic oxidation of EE2 by BMO occurs. (2) P. putida MnB1 indirectly oxidizes EE2 by transferring electrons from the Mn (III) intermediate. (3) P. putida MnB1 continuously re-oxidizes the Mn(II) released from the oxidative degradation of EE2 by BMO, generating new Mn(III)-intermediates or BMO.