Green-Solvent-Processable Composite Micro/Nanofiber Membrane with Gradient Asymmetric Structure for Efficient Microfiltration

Electrospinning technology has attracted extensive attention in recent decades and is widely used to prepare nanofiber membranes from hundreds of polymers. Polyvinyl formal acetal (PVFA), as a polymer with excellent properties such as high strength and heat resistance, is not reported on the electrospun water treatment membrane. In this paper, the preparation process of electrospun PVFA nanofiber membrane is optimized, and the effect of sodium chloride (NaCl) addition on the physical and mechanical properties and microfiltration performance of nanofiber membrane is also explored. And the hydrophobic PVFA nanofiber filter layer is then combined with a hydrophilic nonwoven support layer to construct a composite micro/nanofiber membrane with a pore-size gradient structure and a hydrophilic/hydrophobic asymmetric structure. Finally, unidirectional water transport and water treatment performance are further investigated. The results show that the tensile breaking strength of the composite membrane can reach up to 37.8 MPa, the retention rate for particles with the size of 0.1-0.3 µm is 99.7%, and the water flux is 513.4 L m-2 h-1 under the hydrostatic pressure. Moreover, it still has a retention of more than 98% after three repeated uses. Therefore, the electrospun PVFA composite membrane has a great potential in microfiltration.

Research Progress of Water Treatment Technology Based on Nanofiber Membranes

In the field of water purification, membrane separation technology plays a significant role. Electrospinning has emerged as a primary method to produce nanofiber membranes due to its straightforward, low cost, functional diversity, and process controllability. It is possible to flexibly control the structural characteristics of electrospun nanofiber membranes as well as carry out various membrane material combinations to make full use of their various properties, including high porosity, high selectivity, and microporous permeability to obtain high-performance water treatment membranes. These water separation membranes can satisfy the fast and efficient purification requirements in different water purification applications due to their high filtration efficiency. The current research on water treatment membranes is still focused on creating high-permeability membranes with outstanding selectivity, remarkable antifouling performance, superior physical and chemical performance, and long-term stability. This paper reviewed the preparation methods and properties of electrospun nanofiber membranes for water treatment in various fields, including microfiltration, ultrafiltration, nanofiltration, reverse osmosis, forward osmosis, and other special applications. Lastly, various antifouling technologies and research progress of water treatment membranes were discussed, and the future development direction of electrospun nanofiber membranes for water treatment was also presented.

Porous Cellulose Acetate/Block Copolymer Membranes for the Recovery of Polyphenolic Compounds from Aquatic Environments

Polyphenols are natural compounds with strong antioxidant properties synthesized by plants and widely distributed in plant tissues. They compose a broad class of compounds that are commonly employed for multiple applications such as food, pharmaceutical, adhesives, biomedical, agricultural, and industrial purposes. Runoffs from these sources result in the introduction of polyphenols into aquatic environments where they further transform into highly toxic pollutants that can negatively affect aquatic ecosystems and humans. Therefore, the development of extraction and remediation methods for such compounds must be addressed. This study describes the identification and operation of a method to recover polyphenolic compounds from water environments by utilizing membrane-based separation. Composite membranes derived from electrospun cellulose acetate (CA) fibers and diblock copolymer (DiBCP) PEO-b-P4VP were prepared to evaluate the adsorption of polyphenolic compounds from aqueous environments. The highly porous CA fibers were developed using the electrospinning technique, and the fabricated DiBCP/CA membranes were characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared (FT-IR) spectroscopy, and tensile testing. Finally, the ability of the composite membranes to adsorb the soluble polyphenolic compounds catechol (CAT) and gallic acid (GA), from a wetland environment, was studied via batch adsorption experiments and by solid-phase extraction (SPE). Results revealed a successful recovery of both polyphenols, at concentrations within the parts per million (ppm) range, from the aqueous media. This suggests a novel approach to recover these compounds to prevent their transformation into toxic pollutants upon entrance to water environments.

Recent Progress of Layer-by-layer Assembly, Free-Standing Film and Hydrogel Based on Polyelectrolytes

Nowadays, polyelectrolytes play an essential role in the development of new materials. Their use allows creating new properties of materials and surfaces and vary them in a wide range. Basically, modern methods are divided into three areas-the process of layer-by-layer deposition, free-standing films, and hydrogels based on polyelectrolytes. Layer-by-layer assembly of polyelectrolytes on various surfaces is a powerful technique. It allows giving surfaces new properties, for example, protect them from corrosion. Free-standing films are essential tools for the design of membranes and sensors. Hydrogels based on polyelectrolytes have recently shown their applicability in electrical and materials science. The creation of new materials and components with controlled properties can be achieved using polyelectrolytes. This review focuses on new technologies that have been developed with polyelectrolytes over the last five years.

Porous polymeric membranes: fabrication techniques and biomedical applications

Porous polymeric membranes have shown great potential in biological and biomedical applications such as tissue engineering, bioseparation, and biosensing, due to their structural flexibility, versatile surface chemistry, and biocompatibility. This review outlines the advantages and limitations of the fabrication techniques commonly used to produce porous polymeric membranes, with especial focus on those featuring nano/submicron scale pores, which include track etching, nanoimprinting, block-copolymer self-assembly, and electrospinning. Recent advances in membrane technology have been key to facilitate precise control of pore size, shape, density and surface properties. The review provides a critical overview of the main biological and biomedical applications of these porous polymeric membranes, especially focusing on drug delivery, tissue engineering, biosensing, and bioseparation. The effect of the membrane material and pore morphology on the role of the membranes for each specific application as well as the specific fabrication challenges, and future prospects of these membranes are thoroughly discussed.

A thin film nanocomposite membrane with pre-immobilized UiO-66-NH2 toward enhanced nanofiltration performance

A facile controlled interfacial polymerization strategy was proposed for the synthesis of novel thin film nanocomposite (TFN) membranes for enhanced nanofiltration performance. UiO-66 nanoparticles were aminated and pre-immobilized onto a polymer substrate via polydopamine (PDA) coating to achieve a continuous and defect-free polyamide dense layer. The mediation of the PDA coating could not only enhance the structural stability of TFN nanofiltration membranes, but also improve the dispersion and anchorage of UiO-66-NH2, thus closely fixing the position of UiO-66-NH2 nanoparticles on the polymer substrate. Moreover, since the amino group (-NH2) further reacted with PDA via Michael addition or Schiff base reaction, the in situ mutual reaction reduced the nanoparticle losses significantly during the draining off of the monomer solution in the fabrication process, which effectively cut down the actual dosage. The results showed that the PDA interlayer could induce the tight attachment of the PA layer to the support, enhancing the structural stability of TFN membranes. Furthermore, the dosage of UiO-66-NH2 in the as-prepared TFN membranes could also be decreased to as low as 0.01 w/v%, which was nearly a 10-20-fold reduction in the required amount of UiO-66-NH2 for the synthesis. The fabricated TFN/UiO-66-NH2 membranes exhibited very high water permeance and competitive salt rejections in cross-flow nanofiltration, which shows the huge potential for the application of novel TFN membranes with controlled nanoparticle incorporation in industrial separation.