A low-temperature active and selective bimetallic Cu-In catalysts for hydrogenation of methyl 3-hydroxypropionate to 1,3-propanediol

The pathway for producing 1,3-propanediol (1,3-PDO) from methyl 3-hydroxypropionate (3-HPM) has great application potential. However, the reaction is sensitive to temperature and results in reduced product selectivity at high temperatures. This study explores the use of low-temperature active Cu-In bimetallic catalysts for the 3-HPM reaction. The Cu-1In/SiO2 catalyst exhibits superior catalytic performance with a 91.5 % yield of 1,3-PDO, surpassing that of the Cu/SiO2 catalyst by 264 % under identical conditions. Multiple characterization methods reveal the textural and physiochemical properties of the catalysts. The excellent catalytic performance of Cu-1In/SiO2 can be attributed to the introduction of CuIn alloy and highly dispersed In2O3. The interaction between copper and Indium species on the catalyst surface facilitates the dispersion of Cu species, while simultaneously highly dispersed In2O3 introducing new adsorption sites for reactants, thereby greatly improving its catalytic performance.

Integrated In Situ Fabrication of CuO Nanorod-Decorated Polymer Membranes for the Catalytic Flow-Through Reduction of p-Nitrophenol

We developed a novel method to fabricate copper nanorods in situ in a poly(ether sulfone) (15 wt %) casting solution by a sonochemical reduction of Cu2+ ions with NaBH4. The main twist is the addition of ethanol to remove excess NaBH4 through Cu(0) catalyzed ethanolysis. This enabled the direct use of the resulting copper-containing casting dispersions for membrane preparation by liquid nonsolvent-induced phase separation and led to full utilization of the copper source, generating zero metal waste. We characterized the copper nanorods as presented in the membranes via scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and UV/vis spectroscopy. We could demonstrate that the rapid immobilization from reducing conditions led to the membrane incorporation of copper nanorods in a state of high reactivity, which also promoted the complete oxidation to CuO after fabrication. We further observed a large aspect ratio and crystal straining of the nanorods, likely resulting from growth around the matrix polymer. The entanglement with poly(ether sulfone) further facilitated a selective presentation at the pore surface of the final CuO-decorated membranes. The membranes also exhibit high water permeances of up to 2800 L/m2hbar. Our catalytic membranes achieved exceptionally high activities in the aqueous flow-through reduction of p-nitrophenol (p-NP), with turnover frequencies of up to 115 h-1, even surpassing those of other state-of-the-art catalytic membranes that incorporate Pd or Ag. Additionally, we demonstrated that catalytic hydrolysis of the reducing agent in water can lead to hydrogen gas formation and blocking of active sites during continuous catalytic p-NP hydrogenation. We illustrated that the accompanying conversion loss can be mitigated by facilitated gas transport in the water-filled pores, which is dependent on the orientation of the pore size gradient and the flow direction.

Cu/SiO2 synthesized with HKUST-1 as precursor: high ratio of Cu+/(Cu+ + Cu0) and rich oxygen defects for efficient catalytic hydrogenation of furfural to 2-methyl furan

Cu/SiO2 is one of the most promising catalysts for the furfural (FF) hydrogenation reaction but suffers from the difficulty of tailoring the microstructure and surface properties. Herein, we developed a MOF-derived Cu/SiO2 catalyst (Cu/SiO2-MOF) for FF hydrogenation to 2-methyl furan (2-MF). In comparison with Cu/SiO2 catalysts prepared from ammonia evaporation (Cu/SiO2-AE) and traditional impregnation (Cu/SiO2-TI), the copper species in Cu/SiO2-MOF could not only be anchored on the silica surface via forming Cu-O-Si bonds but also exposed many more active sites. In this way, a higher ratio of Cu+/(Cu+ + Cu0) and richer oxygen defects were constructed via strong metal-support interactions, which were responsible for the superior catalytic performance. In addition, it was found that the solvent effect on product distribution played an important role in adjusting the selectivity to 2-MF and cyclopentanone (CPO). The present work not only provides a deep insight into the catalytic mechanism of Cu/SiO2-MOF for the FF hydrogenation reaction but also sheds light on the design and synthesis of highly efficient catalysts for other heterogeneous catalysis fields.

Hydrogenation of different carbon substrates into light hydrocarbons by ball milling

The conversion of carbon-based solids, like non-recyclable plastics, biomass, and coal, into small molecules appears attractive from different points of view. However, the strong carbon-carbon bonds in these substances pose a severe obstacle, and thus-if such reactions are possible at all-high temperatures are required1-5. The Bergius process for coal conversion to hydrocarbons requires temperatures above 450 °C6, pyrolysis of different polymers to pyrolysis oil is also typically carried out at similar temperatures7,8. We have now discovered that efficient hydrogenation of different solid substrates with the carbon-based backbone to light hydrocarbons can be achieved at room temperature by ball milling. This mechanocatalytic method is surprisingly effective for a broad range of different carbon substrates, including even diamond. The reaction is found to proceed via a radical mechanism, as demonstrated by reactions in the presence of radical scavengers. This finding also adds to the currently limited knowledge in understanding mechanisms of reactions induced by ball milling. The results, guided by the insight into the mechanism, could induce more extended exploration to broaden the application scope and help to address the problem of plastic waste by a mechanocatalytic approach.

The Effect of Lithium Ion Leaching from Calcined Li-Al Hydrotalcite on the Rapid Removal of Ni2+/Cu2+ from Contaminated Aqueous Solutions

A layered double hydroxide (LDH) calcined-framework adsorbent was investigated for the rapid removal of heavy metal cations from plating wastewater. Li-Al-CO₃ LDH was synthesized on an aluminum lathe waste frame surface to prepare the sorbent. The calcination treatment modified the LDH surface properties, such as the hydrophilicity and the surface pH. The change in surface functional groups and the leaching of lithium ions affected the surface properties and the adsorption capacity of the heavy metal cations. A zeta potential analysis confirmed that the 400 °C calcination changed the LDH surface from positively charged (+10 mV) to negatively charged (-17 mV). This negatively charged surface contributed to the sorbent instantly bonding with heavy metal cations in large quantities, as occurs during contact with wastewater. The adsorption isotherms could be fitted using the Freundlich model. The pseudo-second-order model and the rate-controlled liquid-film diffusion model successfully simulated the adsorption kinetics, suggesting that the critical adsorption step was a heterogeneous surface reaction. This study also confirmed that the recovered nickel and/or copper species could be converted into supported metal nanoparticles with a high-temperature hydrogen reduction treatment, which could be reused as catalysts.

Production of Butane from Methyl Ethyl Ketone over Pt/Al2O3

Methyl ethyl ketone (MEK) was catalytically converted to butane directly in one step over platinum (Pt) supported on alumina (Al2O3). The reaction was performed in the gas phase in a fixed bed reactor. Conversion of MEK to butane was achieved by hydrogenation of MEK to 2-butanol, dehydration of 2-butanol to butene, and further hydrogenation of butene to butane. The results showed that butane can be produced with selectivity reaching 95% depending on the operating conditions. The highest selectivity for butane was obtained at 220 °C and a H2/MEK molar ratio of 15. Copyright © 2023 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Emerging catalysts for the ambient synthesis of ethylene glycol from CO2 and its derivatives

Ethylene glycol (EG), a useful chemical raw material, has been widely applied in many aspects of modern society. The conventional preparation of ethylene glycol mainly uses the petroleum route at high temperatures and pressure. More and more approaches have been developed to synthesize EG from CO₂ and its derivatives under mild conditions. In this review, the ambient synthesis of EG from thermocatalysis, photocatalysis, and electrocatalysis is highlighted. The coal-to-ethylene glycol technology, one of the typical thermal catalysis routes for EG preparation, is relatively mature. However, it still faces some problems to be solved in industrialization. The recent progress in the development of coal-to-ethylene glycol technology is introduced. The main focus is on how to realize the preparation of EG under mild conditions. The strategies include doping promoters, modification of supports, design of catalysts with special structures, etc. Furthermore, the emerging technological progress of photocatalytic and electrocatalytic ethylene glycol synthesis under ambient conditions is introduced. Compared with the thermal catalytic reaction, the reaction conditions are milder. However, there are still many problems in large-scale production. Finally, we propose future development issues and related prospects for the ambient synthesis of EG using different catalytic routes.

Effect of Reducing Agent on Characteristics and Antibacterial Activity of Copper-Containing Particles in Textile Materials

Textile materials modified with copper-containing particles have antibacterial and antiviral properties that have prospects for use in healthcare. In the study, textile materials were saturated with copper-containing particles in their entire material volume by the absorption/diffusion method. The antibacterial properties of modified textile materials were confirmed by their inhibitory effect on Staphylococcus aureus, a Gram-positive bacterium that spreads predominantly through the respiratory tract. For the modification, ordinary textile materials of various origins and fiber structures were used. Technological conditions and compositions of modifying solutions were established, as well as the most suitable textile materials for modification. To assess the morphological and physical characteristics of copper-containing particles and the textile materials themselves, X-ray diffraction, a scanning electron microscope, and an energy-dispersive X-ray spectrum were used. In modified textile samples, XRD data showed the presence of crystalline phases of copper (Cu) and copper (I) oxide (Cu2O). On the grounds of the SEM/EDS analysis, the saturation of textile materials with copper-containing particles depends on the structure of the textile materials and the origins of the fibers included in their composition, as well as the modification conditions and the copper precursor.

Electronic Metal-Support Interactions Between CuxO and ZnO for CuxO/ZnO Catalysts With Enhanced CO Oxidation Activity

Metal-support interaction has been one of the main topics of research on supported catalysts all the time. However, many other factors including the particle size, shape and chemical composition can have significant influences on the catalytic performance when considering the role of metal-support interaction. Herein, we have designed a series of CuxO/ZnO catalysts as examples to quantitatively investigate how the metal-support interaction influences the catalytic performance. The electronic metal-support interactions between CuxO and ZnO were regulated successfully without altering the structure of CuxO/ZnO catalyst. Due to the lower work function of ZnO, electrons would transfer from ZnO to CuO, which is favorable for the formation of higher active Cu species. Combined experimental and theoretical calculations revealed that electron-rich interface result from interaction was favorable for the adsorption of oxygen and CO oxidation reaction. Such strategy represents a new direction to boost the catalytic activity of supported catalysts in various applications.

Copper Supported on Ceria Mesocellular Foam Silica as an Effective Catalyst for Reductive Condensation of Acetone to Methyl Isobutyl Ketone

Copper-containing materials based on Ce- and Ca-Nb-mesocellular foam (MCF) silica supports are prepared, characterized and applied as catalysts for gas-phase reductive condensation of acetone to produce methyl isobutyl ketone (MIBK). The properties of the materials, the interaction of metal species, and their role in the catalytic process are examined by nitrogen physisorption, XRD, XPS, CO₂ -TPD, H₂ -TPR, and chemisorption of NO and pyridine combined with FTIR spectroscopy. A synergistic interaction of Cu²⁺ , Cu⁰ , and CeO₂ species incorporated in the MCF support enable the Cu/Ce-MCF catalyst to yield 34 % of acetone conversion with over 90 % MIBK selectivity at 250 °C. Moreover, this high catalyst selectivity is maintained during operation for 24 h despite a decline in catalyst activity. The catalytic performance is superior to that of hydroxyapatite-supported Cu and similar previously reported Pd-containing catalysts.

Catalytic Hydrogenation of CO2 to Methanol: A Review

High-efficiency utilization of CO2 facilitates the reduction of CO2 concentration in the global atmosphere and hence the alleviation of the greenhouse effect. The catalytic hydrogenation of CO2 to produce value-added chemicals exhibits attractive prospects by potentially building energy recycling loops. Particularly, methanol is one of the practically important objective products, and the catalytic hydrogenation of CO2 to synthesize methanol has been extensively studied. In this review, we focus on some basic concepts on CO2 activation, the recent research advances in the catalytic hydrogenation of CO2 to methanol, the development of high-performance catalysts, and microscopic insight into the reaction mechanisms. Finally, some thinking on the present research and possible future trend is presented.

Insights into a New Formation Mechanism of Robust Cu/SiO2 Catalysts for Low-Temperature Dimethyl Oxalate Hydrogenation Induced by a Chelating Ligand of EDTA

The Cu/SiO2 catalyst has been widely used in dimethyl oxalate (DMO) hydrogenation due to its low cost and high efficiency. However, the reaction temperature of DMO hydrogenation is higher than the Hüttig temperature of Cu, and the smaller Cu particles are easier to agglomerate. Therefore, there is much interest in constructing a catalyst with a small particle size and strong stability. In the present work, the effect of introducing EDTA on Cu/SiO2 catalysts is systematically investigated. It not only was beneficial to form smaller copper nanoparticles (CuNPs) but also to enhance the stability of Cu species by introducing a suitable amount of EDTA. Furthermore, the surface Cu species were more evenly dispersed, and the number of active sites was increased with the introduction of EDTA; subsequently, the synergistic effect between Cu+ and Cu0 was enhanced. The best performance of 0.08E-Cu/SiO2 had been achieved in the DMO hydrogenation to ethylene glycol (EG), and the DMO conversion and EG selectivity reached 99.9% and 97.7%, respectively. Above all, the 0.08E-Cu/SiO2 catalyst exhibited a high level of stability during the 1200 h life test at 180 °C.

CuZnAl-Oxide Nanopyramidal Mesoporous Materials for the Electrocatalytic CO2 Reduction to Syngas: Tuning of H2/CO Ratio

Inspired by the knowledge of the thermocatalytic CO₂ reduction process, novel nanocrystalline CuZnAl-oxide based catalysts with pyramidal mesoporous structures are here proposed for the CO₂ electrochemical reduction under ambient conditions. The XPS analyses revealed that the co-presence of ZnO and Al₂O₃ into the Cu-based catalyst stabilize the CuO crystalline structure and introduce basic sites on the ternary as-synthesized catalyst. In contrast, the as-prepared CuZn- and Cu-based materials contain a higher amount of superficial Cu⁰ and Cu¹⁺ species. The CuZnAl-catalyst exhibited enhanced catalytic performance for the CO and H₂ production, reaching a Faradaic efficiency (FE) towards syngas of almost 95% at −0.89 V vs. RHE and a remarkable current density of up to 90 mA cm⁻² for the CO₂ reduction at −2.4 V vs. RHE. The physico-chemical characterizations confirmed that the pyramidal mesoporous structure of this material, which is constituted by a high pore volume and small CuO crystals, plays a fundamental role in its low diffusional mass-transfer resistance. The CO-productivity on the CuZnAl-catalyst increased at more negative applied potentials, leading to the production of syngas with a tunable H₂/CO ratio (from 2 to 7), depending on the applied potential. These results pave the way to substitute state-of-the-art noble metals (e.g., Ag, Au) with this abundant and cost-effective catalyst to produce syngas. Moreover, the post-reaction analyses demonstrated the stabilization of Cu₂O species, avoiding its complete reduction to Cu⁰ under the CO₂ electroreduction conditions.

Intermediate Cu-O-Si Phase in the Cu-SiO2/Si(111) System: Growth, Elemental, and Electrical Studies

We investigate here the strain-induced growth of Cu at 600 °C and its interactions with a thermally grown, 270 nm-thick SiO₂ layer on the Si(111) substrate. Our results show clear evidence of triangular voids and formation of triangular islands on the surface via a void-filling mechanism upon Cu deposition, even on a 270 nm-thick dielectric. Different coordination states, oxidation numbers, and chemical compositions of the Cu-grown film are estimated from the core level X-ray photoelectron spectroscopy (XPS) measurements. We find evidence of different compound phases including an intermediate mixed-state of Cu-O-Si at the interface. Emergence of a mixed Cu-O-Si intermediate state is attributed to the new chemical states of Cu ^x+, O ^x , and Si ^x+ observed in the high-resolution XPS spectra. This intermediate state, which is supposed to be highly catalytic, is found in the sample with a concentration as high as ∼41%. Within the Cu-O-Si phase, the atomic percentages of Cu, O, and Si are ∼1, ∼86, and ∼13%, respectively. The electrical measurements carried out on the sample reveal different resistive channels across the film and an overall n-type semiconducting nature with a sheet resistance of the order of 10⁶ Ω.

Bimetallic Co/Zn zeolitic imidazolate framework ZIF-67 supported Cu nanoparticles: An excellent catalyst for reduction of synthetic dyes and nitroarenes

In this study, a sub-class of microporous crystalline metal organic frameworks (MOFs) with zeolite-like configurations, i.e., zeolitic imidazolate frameworks of single node ZIF-67 and binary nodes ZIF-Co/Zn are used as the supports to develop Cu nanoparticles based nanocatalysts. Their catalytic activities are comparatively evaluated where Cu(x)@ZIF-Co/Zn exhibits better performances than Cu(x)@ZIF-67 in the reduction of synthetic dyes and nitroarenes. For instance, the Cu(0.25)@ZIF-Co/Zn catalyst shows an excellent reaction rate of 2.088 × 10^-2 s^-1 and an outstanding activity of 104.4 s^-1g_cat^-1 for the reduction of methyl orange. The same catalyst also performs an exceptional catalytic activity in the hydrogenation of p-nitrophenol to p-aminophenol with the activity of 216.5 s^-1g_cat^-1. A synergistic role of unique electronic properties rising from the direct contact of Cu NPs with the bimetallic nodes ZIF-Co/Zn, higher surface area of support, appropriate Cu loading and maintainable microporous frameworks with higher thermal and hydrolytic stability collectively enhances the catalytic activity of Cu(x)@ZIF-Co/Zn. Moreover, this catalyst shows excellent stability and recyclability, which can retain high conversion after reuse for 10 cycles.

Elucidation of copper environment in a Cu-Cr-Fe oxide catalyst through in situ high-resolution XANES investigation

Copper containing materials are widely used in a range of catalytic applications. Here, we report the use of Cu K-edge high resolution XANES to determine the local site symmetry of copper ions during the thermal treatment of a Cu-Cr-Fe oxide catalyst. We exploited the Cu K-edge XANES spectral features, in particular the correlation between area under the pre-edge peak and its position to determine the local environment of Cu2+ ions. The information gained from this investigation rules out the presence of Cu2+ ions in a tetrahedral or square planar geometry, a mixture of these sites, or in a reduced oxidation state. Evidence is presented that the Cu2+ ions in the Cu-Cr-Fe oxide system are present in a distorted octahedral environment.

Engineering of Yolk/Core-Shell Structured Nanoreactors for Thermal Hydrogenations

Heterogeneous hydrogenation reactions are of great importance for chemical upgrading and synthesis, but still face the challenges of controlling selectivity and long-term stability. To improve the catalytic performance, many hydrogenation reactions utilize special yolk/core-shell nanoreactors (YCSNs) with unique architectures and advantageous properties. This work presents the developmental and technological challenges in the preparation of YCSNs that are potentially useful for hydrogenation reactions, and provides a summary of the properties of these materials. The work also addresses the scientific challenges in applications of these YCSNs in various gas and liquid-phase hydrogenation reactions. The catalyst structures, catalytic performance, structure-performance relationships, reaction mechanisms, and unsolved problems are discussed too. Also, a brief outlook and opportunities for future research in this field are presented. This work on the advancements in YCSNs might inspire the creation of new materials with desired structures for achieving maximal hydrogenation performances.

Copper Phyllosilicates-Derived Catalysts in the Production of Alcohols from Hydrogenation of Carboxylates, Carboxylic Acids, Carbonates, Formyls, and CO2: A Review

Copper phyllosilicates-derived catalysts (CuPS-cats) have been intensively explored in the past two decades due to their promising activity in carbonyls hydrogenation. However, CuPS-cats have not been completely reviewed. This paper focuses on the aspects concerning CuPS-cats from synthesis methods, effects of preparation conditions, and dopant to catalytic applications of CuPS-cats. The applications of CuPS-cats include the hydrogenation of carboxylates, carboxylic acids, carbonates, formyls, and CO2 to their respective alcohols. Besides, important factors such as the Cu dispersion, Cu+ and Cu0 surface areas, particles size, interaction between Cu and supports and dopants, morphologies, and spatial effect on catalytic performance of CuPS-cats are discussed. The deactivation and remedial actions to improve the stability of CuPS-cats are summarized. It ends up with the challenges and prospective by using this type of catalyst.

Positive effects of a halloysite-supported Cu/Co catalyst fabricated by a urea-driven deposition precipitation method on the CO-SCR reaction and SO2 poisoning

Cu/Co catalysts were prepared on halloysite nanotube supports by a urea-driven deposition–precipitation method for CO oxidation and the selective catalytic reduction of NO (CO-SCR).

Promotional effect of indium on Cu/SiO2 catalysts for the hydrogenation of dimethyl oxalate to ethylene glycol

CuIn/SiO2 with 1.0 wt% indium shows the best catalytic performance for DMO hydrogenation to EG. The synergistic effect of Cu0–Cu+–CuIn alloy in activating H2 molecules and carbonyl bonds is elucidated.

Hydrophobic Copper Catalysts Derived from Copper Phyllosilicates in the Hydrogenation of Levulinic Acid to γ-Valerolactone

A reduction-silylation-reduction method was developed to synthesize hydrophobic Cu catalysts derived from Cu phyllosilicates (CuPS). Triethoxy(octyl)silane (OTS) was used as the coupling agent. The OTS-grafted, reduced CuPS catalysts were applied in the hydrogenation of levulinic acid (LA) to γ-valerolactone (GVL). The most promising catalyst was synthesized by reducing CuPS at a high temperature (350 °C for 3 h), followed by OTS grafting, and then by repeating the previous reduction step. High LA conversion (95.7%), GVL yield (85.2%), and stability (3 cycles with a 7.5% loss of initial activity) were obtained at a mild reaction condition (130 °C with a H₂ pressure of 12 bar). A high reduction temperature not only leads to a low oxidation state of Cu species but also suppresses the formation of silylation-induced acids. Moreover, the intrinsic activity of a reduced CuPS catalyst was nearly intact after subjecting to silylation and the second reduction treatment.

Development of a Simple Reversible-Flow Method for Preparation of Micron-Size Chitosan-Cu(II) Catalyst Particles and Their Testing of Activity

A simple flow system employing a reversible-flow syringe pump was employed to synthesize uniform micron-size particles of chitosan-Cu(II) (CS-Cu(II)) catalyst. A solution of chitosan and Cu(II) salt was drawn into a holding coil via a 3-way switching valve and then slowly pumped to drip into an alkaline solution to form of hydrogel droplets. The droplets were washed and dried to obtain the catalyst particles. Manual addition into the alkaline solution or employment of flow system with a vibrating rod, through which the end of the flow line is inserted, was investigated for comparison. A sampling method was selected to obtain representative samples of the population of the synthesized particles for size measurement using optical microscopy. The mean sizes of the particles were 880 ± 70 µm, 780 ± 20 µm, and 180 ± 30 µm for the manual and flow methods, without and with the vibrating rod, respectively. Performance of the flow methods, in terms of rate of droplet production and particle size distribution, are discussed. Samples of 180 µm size CS-Cu(II) particles were tested for catalytic reduction of 0.5 mM p-nitrophenol to p-aminophenol by 100-fold excess borohydride. The conversion was 98% after 20 min, whereas without the catalyst there was only 14% conversion.

Continuous production of propylene glycol (1,2-propanediol) by the hydrogenolysis of glycerol over a bi-functional Cu–Ru/MgO catalyst

A series of Cu–Ru/MgO catalysts were developed for the continuous production of propylene glycol from glycerol in a sectionally packed downflow tubular reactor in the vapor phase.

Effect of Aging Methods on CuZnAl Catalysts for Methyl Acetate Hydrogenation

A series of CuZnAl catalysts derived from layered double hydroxide precursors with different Cu/Zn molar ratios were synthesised by a co-precipitation method for methyl acetate hydrogenation. The best catalytic performance was obtained when the Cu/Zn molar ratio reached 0.25:1. After fixing the Cu/Zn molar ratio at 0.25:1, the effect of aging methods, including ultrasound, high shear mixer stirring, and magnetic stirring, were investigated, which showed that 0.25CuZnAl-u and 0.25CuZnAl-h exhibited a higher conversion and selectivity than that of 0.25CuZnAl-m, especially under low reaction temperatures. The physicochemical properties of the CuZnAl catalysts were characterised by X-ray diffraction, inductively coupled plasma–atomic emission spectroscopy, N2 physisorption, N2O chemisorption, transmission electron microscopy, H2-temperature-programmed reduction, X-ray photoelectron spectroscopy, and H2-temperature-programmed desorption. It was found that compared with 0.25CuZnAl-m, 0.25CuZnAl-u and 0.25CuZnAl-h possessed a stronger interaction between Cu and the support, smaller copper particle size, and higher copper dispersion, which improved the catalytic performance.

Production of propylene glycol (1,2-propanediol) by the hydrogenolysis of glycerol in a fixed-bed downflow tubular reactor over a highly effective Cu–Zn bifunctional catalyst: effect of an acidic/basic support

Very high glycerol conversion of 98.5% with ∼89% selectivity to propylene glycol was achieved at a very low pressure (0.72 MPa) over Cu–Zn/MgO catalyst for vapor phase hydrogenolysis of glycerol. Uniformly distributed partially reduced copper species (Cu₂O, CuO, and Cu⁰) and higher basicity of the catalyst were the governing factors for higher selectivity to propylene glycol.

Importance of the Initial Oxidation State of Copper for the Catalytic Hydrogenation of Dimethyl Oxalate to Ethylene Glycol

Exposing a Cu‐based catalyst to a suitable temperature is of great importance to optimize its hydrogenation performance, as copper is sensitive to temperature. Herein, we investigated the effect of the initial oxidation state of copper, tuned by the reduction temperature, on its catalytic performance in the hydrogenation of dimethyl oxalate (DMO) to ethylene glycol (EG) through designing a series of catalysts with different reduction temperatures (200–350 °C). Among these catalysts, the Cu/SiO₂ catalyst prepared by ammonia evaporation with a hydrogen reduction process at 250 °C showed the best performance in the hydrogenation of DMO with a conversion of 100 % and a selectivity to EG higher than 95 %. The relationship between the initial oxidation state of copper and catalytic performance was well established by characterizing the physicochemical properties of the Cu/SiO₂ catalysts by XRD, TEM, H₂ temperature‐programmed reduction, N₂O adsorption, and in situ reduction Auger electron spectroscopy. The initial oxidation state of copper determined the conversion of DMO and the distribution of the products, and it could be balanced by reducing the temperature to improve the activity of the catalyst. This work provides a reference for further exploration of the mechanism and guidance for the design of catalysts for the hydrogenation of esters.