Surface functionality analysis by Boehm titration of graphene nanoplatelets functionalized via a solvent-free cycloaddition reaction

Pyrene-functionalized poly(methacrylic acid) acts as an efficient stabilizer for graphene nanoplatelets and facilitates their use in waterborne latex formulations

HYPOTHESIS

Pyrene derivatives are effective motifs when designing graphene-philic surfactants, enabling the use of hydrophobic graphene-based nanomaterials in waterborne formulations. Hence, novel pyrene end-functionalized polymeric stabilizers show promise for stabilizing aqueous graphene nanomaterial dispersions, and offer benefits over traditional small molecule surfactants.

EXPERIMENTS

Pyrene end-functionalized poly(methacrylic acid) (Py-PMAAn, where n = 68 to 128) was synthesized by reversible addition-fragmentation chain-transfer (RAFT) polymerization of MAA using a pyrene-containing RAFT chain-transfer agent. These polymers were evaluated as aqueous graphene nanoplatelet (GNP) stabilizers. Subsequently, polymer-stabilized GNPs were formulated into film-forming polymer latex dispersions and the properties of the resulting GNP-containing films measured.

FINDINGS

Py-PMAAn homopolymers with well-defined molecular weights were prepared via RAFT solution polymerization. They served as efficient stabilizers for aqueous GNP dispersions and performed better than a traditional small molecule surfactant and non-functionalized PMAA, especially at higher pH and with higher molecular weight polymers. The use of Py-PMAAn allowed GNPs to be readily formulated into waterborne latex coatings. When compared to controls, the resulting films were significantly reinforced due to the improved homogeneity of dried nanocomposite films and chain entanglement between the polymer matrix and stabilizers. Thus, the ability to readily incorporate GNPs into aqueous formulations and enhance GNP/polymer matrix interfaces was demonstrated for these novel amphiphilic stabilizers.

Adsorption dynamics of Cd2+(aq) on microwave-synthetized pristine biochar from cocoa pod husk: Green, experimental, and DFT approaches

Biochar obtained via microwave-assisted pyrolysis (MAP) at 720 W and 15 min from cocoa pod husk (CPH) is an efficient adsorbent of Cd2+(aq). Biochar of residual biomass of CPH (BCCPH) possesses favorable physicochemical and morphological properties, featuring a modest surface area yet a suitable porous structure. Adsorption, predominantly governed by physisorption, is influenced by the oxygen-containing active sites (-COOR, -C(R)O, and -CH2OR; R = H, alkyl). CdCO3 formation occurs during adsorption. Experimental data were well-fitted into various kinetic models for a broad understanding of the sorption process. Langmuir model indicates a maximum adsorption capacity of 14.694 mg/g. The thermodynamic study confirms the spontaneous and endothermic sorption. Studies at the molecular level have revealed that the Cd2+ ion tends to bind to surface aromatic carbon atoms. This sustainable approach produces BCCPH via MAP as a solution for waste transformation into water-cleaning materials.

Effects of different modifying agents on the preparation and properties of coagulants derived from excess sludge

The contents and kinds of oxygen-containing functional groups are very significant when preparing cationic hydrochar coagulants via graft copolymerization. Herein, the hydrothermal conditions to produce sludge-based hydrochar (SBC) precursors were optimized by introducing different kinds and amounts of modifying agents (i.e., HCOOH, citric acid (CA), H2SO4, and H2O2), then the surface properties and flocculation performance of derived cationic coagulants (SBC-g-DMC) were studied. Results showed that the utilization of four modifiers raised the acidic groups on the SBC surface; thereinto, the presence of CA could evidently increase the content of phenolic hydroxyl groups. After DMC monomer grafting, the formed coagulants possess positive zeta potentials over a wide pH range (i.e., 3.0 ~ 11.0), showing a typical cationic property. The grafting ratio and efficiency, as well as the cationic degree of coagulants prepared with different SBC precursors follow a descending order of SBCCA-g-DMC > [Formula: see text]-g-DMC > SBCHCOOH-g-DMC > [Formula: see text]-g-DMC; thus, SBCCA-g-DMC coagulant with the best grafting result shows a superior flocculation performance. When a dosage of 4 mg/L was adopted, the average turbidity removal rate of SBCCA-g-DMC could reach up to 94.44%. Meanwhile, due to the possible and robust oxidation with the initiator, H2O2 seems not a perfect modifier for SBC preparation. This study could provide an essential reference for the optimal synthesis of SBC and its based coagulants for organic matter recovery and pollutant removal.

International Interlaboratory Comparison of Thermogravimetric Analysis of Graphene-Related Two-Dimensional Materials

Research on graphene-related two-dimensional (2D) materials (GR2Ms) in recent years is strongly moving from academia to industrial sectors with many new developed products and devices on the market. Characterization and quality control of the GR2Ms and their properties are critical for growing industrial translation, which requires the development of appropriate and reliable analytical methods. These challenges are recognized by International Organization for Standardization (ISO 229) and International Electrotechnical Commission (IEC 113) committees to facilitate the development of these methods and standards which are currently in progress. Toward these efforts, the aim of this study was to perform an international interlaboratory comparison (ILC), conducted under Versailles Project on Advanced Materials and Standards (VAMAS) Technical Working Area (TWA) 41 "Graphene and Related 2D Materials" to evaluate the performance (reproducibility and confidence) of the thermogravimetric analysis (TGA) method as a potential new method for chemical characterization of GR2Ms. Three different types of representative and industrially manufactured GR2Ms samples, namely, pristine few-layer graphene (FLG), graphene oxide (GO), and reduced graphene oxide (rGO), were used and supplied to ILC participants to complete the study. The TGA method performance was evaluated by a series of measurements of selected parameters of the chemical and physical properties of these GR2Ms including the number of mass loss steps, thermal stability, temperature of maximum mass change rate (T_p) for each decomposition step, and the mass contents (%) of moisture, oxygen groups, carbon, and impurities (organic and non-combustible residue). TGA measurements determining these parameters were performed using the provided optimized TGA protocol on the same GR2Ms by 12 participants across academia, industry stakeholders, and national metrology institutes. This paper presents these results with corresponding statistical analysis showing low standard deviation and statistical conformity across all participants that confirm that the TGA method can be satisfactorily used for characterization of these parameters and the chemical characterization and quality control of GR2Ms. The common measurement uncertainty for each parameter, key contribution factors were identified with explanations and recommendations for their elimination and improvements toward their implementation for the development of the ISO/IEC standard for chemical characterization of GR2Ms.

Sulfonate-modified calixarene-based porous organic polymers for electrostatic enhancement and efficient rapid removal of cationic dyes in water

Developing of fast and efficient adsorbents for removal of low concentration refractory organics in water is significant. Herein, a novel calix[4]arene-based porous organic polymer CaPy is constructed through Sonogashira-Hagihara cross-coupling polycondensation. The strong polar sulfonate is further anchored onto the polymer skeleton of CaPy and three sulfonate-modified anionic polymers CaPy-S1, CaPy-S2, and CaPy-S3 were obtained and fully characterized. The adsorption isotherms showed that the maximum adsorption capacities of CaPy, CaPy-S1, CaPy-S2, and CaPy-S3 toward methylene blue (MB) were 270, 1454, 558 and 1381 mg g^-1, whereas those for Rhodamine B (RhB) were 183, 2653, 1132, and 1796 mg g^-1, respectively. The maximum adsorption capacity toward RhB was the highest reported vale among the currently used synthetic adsorbents. In addition, the pseudo-second-order rate constants of CaPy, CaPy-S1, CaPy-S2, and CaPy-S3 toward MB were 0.00572, 0.488, 2.24, and 0.192 g mg^-1 min^-1, respectively, and those toward RhB were 0.000234, 0.138, 0.0819, and 0.203 g mg^-1 min^-1, respectively. The pseudo-second-order rate constant of CaPy-S2 toward MB was 2.24 g mg^-1 min^-1 indicating one of the highest adsorption speeds. The activation energy of CaPy-S1 for RhB and MB were 121 and 109 kJ mol^-1, respectively, demonstrating that the adsorption of both dyes on CaPy-S1 was chemisorption process. Further, the obtained values of Gibbs free energy were negative, revealing that the adsorption process was spontaneous. This work provides an effective approach for improving adsorption performance via post-modification.

Physical-Chemical Characterization of Different Carbon-Based Sorbents for Environmental Applications

Biochar has been used in various applications, e.g., as a soil conditioner and in remediation of contaminated water, wastewater, and gaseous emissions. In the latter application, biochar was shown to be a suitable alternative to activated carbon, providing high treatment efficiency. Since biochar is a by-product of waste pyrolysis, its use allows for compliance with circular economics. Thus, this research aims to obtain a detailed characterization of three carbonaceous materials: an activated carbon (CARBOSORB NC 1240^®) and two biochars (RE-CHAR^® and AMBIOTON^®). In particular, the objective of this work is to compare the properties of three carbonaceous materials to evaluate whether the application of the two biochars is the same as that of activated carbon. The characterization included, among others, particle size distribution, elemental analysis, pH, scanning electron microscope, pore volume, specific surface area, and ionic exchange capacity. The results showed that CARBOSORB NC 1240^® presented a higher specific surface (1126.64 m²/g) than AMBIOTON^® (256.23 m²/g) and RE-CHAR^® (280.25 m²/g). Both biochar and activated carbon belong to the category of mesoporous media, showing a pore size between 2 and 50 nm (20-500 Å). Moreover, the chemical composition analysis shows similar C, H, and N composition in the three carbonaceous materials while a higher O composition in RE-CHAR^® (9.9%) than in CARBOSORB NC 1240 ^® (2.67%) and AMBIOTON^® (1.10%). Differences in physical and chemical properties are determined by the feedstock and pyrolysis or gasification temperature. The results obtained allowed to compare the selected materials among each other and with other carbonaceous adsorbents.

Adsorptive separation using self-assembly on graphite: from nanoscale to bulk processes

Adsorptive separation is a promising lower-energy alternative for traditional industrial separation processes. While carbon-based materials have a long history in adsorptive removal of organic contaminants from solution or gas mixtures, separation using an adsorption/desorption protocol is rarely considered. The main drawbacks are the limited control in bulk adsorption experiments, as often all organic molecules are adsorbed, and lack of desorption methods to retrieve the adsorbed molecules. Using high-resolution on-surface characterization with scanning tunneling microscopy (STM), an increased understanding of the on-surface adsorption behavior under different conditions was obtained. The insight obtained from the nanoscale experiments was used to develop a highly selective separation method using adsorption and desorption on graphite, which was tested for the separation of quinonoid zwitterions. These experiments on adsorptive separation using self-assembly on graphite show its potential and demonstrate the advantage of combining surface characterization techniques with bulk experiments to exploit different possible applications of carbon-based materials.

Low Temperature One-Pot Hydrothermal Carbonization of Corn Straw into Hydrochar for Adsorbing Cadmium (II) in Wastewater

Corn straw, a typical agricultural waste, was directly converted into hydrochar with a yield of 77.56% by hydrothermal carbonization at 140–230 °C for 2 h with a solid–liquid ratio of 1:20. The morphology and surface properties were characterized by elemental analysis, specific surface area and pore size analysis and Fourier transform infrared spectroscopy. The results showed that with the increase of hydrothermal reaction temperature, some physical and chemical properties such as the increase of hydrocarbon content, crystallinity, and specific surface area of hydrochar changed significantly. A series of chemical reactions such as dehydration, decarboxylation, and aromatization occurred in the hydrothermal carbonization process so that the prepared hydrochar had rich oxygen-containing functional groups (-HO, C-O-C, C=O) and unique porous structure made the hydrochar prepared at 170 °C had the best removal effect on Cd2+ in solution (5.84 mg/g). These specific conditions could remove Cd2+ and greatly improve the adsorption performance. The pseudo-second-order kinetic model and Freundlich isotherm model could better describe the adsorption behavior of Cd2+. Therefore, corn straw hydrochar as a potential adsorbent for removing Cd2+ from water.

Mechanistic insights into the adsorption of methylene blue by particulate durian peel waste in water

This study aims to investigate the adsorption of methylene blue (MB) over particulate durian peel waste, which is chemically activated with hydrogen peroxide. The equilibrium data are well described by the Freundlich isotherm model, which indicates that the MB adsorption takes place predominantly on multilayers and heterogeneous surfaces of the biosorbent. The Freundlich adsorption constants, K_F and n, are 11.06 L/g and 2.94, respectively. Thermodynamic data suggest that the MB adsorption occurs spontaneously and endothermically. The enthalpy and entropy for the MB adsorption are obtained as 10.26 kJ/mol and 0.058 kJ/mol K, respectively, in the temperature range of 303-323 K. Based on the stepwise desorption method, the adsorption of MB is dominated by physical interactions, particularly hydrogen bonding.

Preparation, characterization, and application of a homemade graphene for the removal of Congo red from aqueous solutions

Ethylene diaminetetraacetic acid (EDTA)-functionalized graphene was synthesized from Nigerian coal using a chemical exfoliation method and the graphene was applied for the removal of Congo red dye from aqueous solutions. The synthesized coal graphene and the raw coal were characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM)-energy-dispersive X-ray (EDX) spectroscopy, measurement of pHpzc (pH of point of zero charge), and Boehm titrations. The SEM data revealed surface roughness which is enhanced in the prepared graphene while the EDX revealed an increase in carbon content, the main constituent of graphene, from about 26% in the raw coal to about 80% in the prepared graphene. Various adsorption variables, such as pH, contact time, concentration of Congo red, and temperature, were varied for the removal of the dye using raw coal and the synthesized coal graphene. The Liu isotherm gave the best fit of the equilibrium data than the Langmuir, Freundlich, and Dubinin-Radushkevich models. The maximum adsorption capacities of the raw coal and synthesized coal graphene at 25°C are 109.1 mg/g and 129.0 mg/g, respectively. The Avrami fractional-order kinetic model was the best model for description of the kinetic data. The model had the lowest values of standard deviation than the pseudo-first-order and pseudo-second-order models. The adsorption process of the two materials occurred via two stages as proved by intraparticle diffusion model. The adsorption process of the Congo red removal was spontaneous, feasible, and endothermic. The study conclusively revealed the graphene nanomaterial to be a viable adsorbent for textile wastewater treatment.

Shedding Light on the Chemistry and the Properties of Münchnone Functionalized Graphene

Münchnones are mesoionic oxazolium 5-oxides with azomethine ylide characteristics that provide pyrrole derivatives by a 1,3-dipolar cycloaddition (1,3-DC) reaction with acetylenic dipolarophiles. Their reactivity was widely exploited for the synthesis of small molecules, but it was not yet investigated for the functionalization of graphene-based materials. Herein, we report our results on the preparation of münchnone functionalized graphene via cycloaddition reactions, followed by the spontaneous loss of carbon dioxide and its further chemical modification to silver/nisin nanocomposites to confer biological properties. A direct functionalization of graphite flakes into few-layers graphene decorated with pyrrole rings on the layer edge was achieved. The success of functionalization was confirmed by micro-Raman and X-ray photoelectron spectroscopies, scanning transmission electron microscopy, and thermogravimetric analysis. The 1,3-DC reactions of münchnone dipole with graphene have been investigated using density functional theory to model graphene. Finally, we explored the reactivity and the processability of münchnone functionalized graphene to produce enriched nano biomaterials endowed with antimicrobial properties.

Enhanced adsorption of Cd (II) from aqueous solution by a shrimp bran modified Typha orientalis biochar

The biochar which was characterized with well-developed facial structure and O-/N-containing functional groups could effectively remove Cd (II) from water. In this paper, Typha orientalis-based biochar (BCS) with well-developed N containing functional groups was modified with shrimp bran which was rich in crude protein for the first time. There are more well-developed O-/N-containing functional groups in the structure of BCS than that of pure Typha orientalis-based biochar without any modification (BC), and this conclusion was depended on their comparisons of Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), elemental analysis (EA), Boehm titration, Fourier transform infrared (FTIR), and other characterization techniques. Moreover, according to the experiment, the phenomenon that the adsorption capacity of Cd(II) on these two adsorbents (BCs) decreased with the increase of solution ionic strength could be carried out. The Cd(II) adsorption studies combined with X-ray photoelectron spectroscopy (XPS) analysis revealed that the adsorption mechanism was mainly attributed to physical microporous filtration and chemical interaction between Cd(II) and the surface functional groups (surface complexation, ion exchange, and electrostatic attraction).

Evaluation of Removal Efficiency of Ni(II) and 2,4-DCP Using in Situ Nitrogen-Doped Biochar Modified with Aquatic Animal Waste

Currently, biochar (BC) has shown promising potential in groundwater and surface-water remediation. In this work, Trapa natans husks based biochar (TBC) was prepared and modified with aquatic animal waste (shrimp and crab) to produce shrimp-modified biochar (SBC) and crab-modified biochar (CBC), respectively. The as-prepared BCs (TBC, SBC, and CBC) were characterized by X-ray diffraction, scanning electron microscopy, elemental analysis, Boehm titration, Fourier transform infrared, and X-ray photoelectron spectroscopy. SBC and CBC had more developed nitrogen-containing functional groups than TBC, which indicates that the crude proteins in shrimp and crab have successfully achieved in situ nitrogen doping. Results of batch experiments showed that SBC and CBC had larger groundwater pollutants (2,4-dichlorophenol (2,4-DCP) and Ni(II)) adsorption capacities than TBC. According to batch adsorption experiment and characterization analysis results, the proposed adsorption mechanism of 2,4-DCP includes hydrogen bonding and π-π electron-donor-acceptor interaction, while the mechanism for Ni(II) adsorption are proposed to be surface complexation, ion exchange, and electrostatic attraction.

Cycloaddition reactions on epitaxial graphene

By means of first principles calculations we studied the occurrence of cycloaddition reactions on the buffer layer of silicon carbide. Interestingly, the presence of the substrate favors the 1,3 cycloaddition instead of the [2+2] or [4+2] ones.