Behavior of the water/vapor interface of chitosan solutions with an anionic surfactant: effect of polymer-surfactant interactions

Preparation of a Chitosan/Coal Gasification Slag Composite Membrane and Its Adsorption and Removal of Cr (VI) and RhB in Water

At present, there are many kinds of pollutants, including dyes and heavy metal ions, in wastewater. It is very important to develop adsorbents that can simultaneously remove heavy metal ions and dyes. In this study, a renewable composite membrane material was synthesized using chitosan and treated coal gasification slag. The Cr (VI) maximum adsorption capacity of the composite membrane was 50.0 mg/L, which was 4.3~8.8% higher than that of the chitosan membrane. For the adsorption of RhB, the removal rate of the chitosan membrane was only approximately 5.0%, but this value could be improved to 95.3% by introducing coal gasification slag. The specific surface area of the chitosan membrane could also be increased 16.2 times by the introduction of coal gasification slag. This is because coal gasification slag could open the nanopores of the chitosan membrane (from 80 μm to 110 μm). Based on the adsorption kinetics and adsorption mechanism analysis, it was found that the adsorption of Cr (VI) occurred mainly through the formation of coordination bonds with the amino groups on the molecular chains of chitosan. Meanwhile, RhB adsorption occurred through the formation of hydrogen bonds with the surface of coal gasification slag. Additionally, coal gasification slag can improve the mechanical properties of the chitosan membrane by 2.2 times, which may facilitate the practical application of the composite membrane. This study provides new insight into the adsorbent design and the resource utilization of coal gasification slag.

Chitosan: A Promising Multifunctional Cosmetic Ingredient for Skin and Hair Care

The cosmetic industry has an undeniable need to design and develop new ecosustainable products to respond to the demands of consumers and international regulations. This requires substituting some traditional ingredients derived from petrochemical sources with new ones with more ecofriendly profiles. However, this transition towards the use of green ingredients in the cosmetic industry cannot compromise the effectiveness of the obtained products. Emerging ingredients in this new direction of the cosmetic industry are chitosan and its derivatives, which combine many interesting physicochemical and biological properties for the fabrication of cosmetic products. Thus, the use of chitosan opens a promising future path to the design of cosmetic formulations. In particular, chitosan’s ability for interacting electrostatically with negatively charged substrates (e.g., skin or damaged hair), resulting in the formation of polymeric films which contribute to the conditioning and moisturizing of cosmetic substrates, makes this polymer an excellent candidate for the design of skin and hair care formulations. This review tries to provide an updated perspective on the potential interest of chitosan and its derivatives as ingredients of cosmetics for skin and hair care.

Studies on Intermolecular Interaction of N-Glycidyltrimethyl Ammonium Chloride Modified Chitosan/N,N-Dimethyl-N-dodecyl-N-(2,3-epoxy propyl) Ammonium Chloride and Curcumin Delivery

Chitosan has potential applications in many fields, due to its biocompatibility, biodegradability and reproducibility. However, the insolubility in water restricts its wide application. In order to expand the application of chitosan in the delivery of oil-soluble drugs and improve the efficacy of oil-soluble drugs, N-Glycidyltrimethyl ammonium chloride-modified chitosan (GTA-m-CS) and N,N-Dimethyl-N-dodecyl-N-(1,2-epoxy propyl) ammonium chloride (DDEAC), a kind of reactive surfactant, were synthesized and characterized by FTIR, NMR and XRD methods. The interactions between GTA-m-CS and DDEAC was studied by surface tension, viscosity, conductivity and fluorescence methods. The parameters, including equilibrium surface tension, critical micelle concentrations of DDEAC with different GTA-m-CS concentration, critical aggregation concentration of DDEAC, the amount of DDEAC adsorbed on GTA-m-CS, pc₂₀ and π_cmc were obtained from the surface tension curves. The influence of temperature on the above parameters were evaluated. The degree of counterion binding to micelle and the thermodynamic parameters of the system were calculated from the conductivity curves. According to the change of conductivity with temperature, the thermodynamic parameters of micellar formation were calculated. The aggregation number of DDEAC molecules in GTA-m-CS/DDEAC aggregates were calculated from steady-state fluorescence data. Based on the experimental results, the interaction models between GTA-m-CS and DDEAC were proposed. The GTA-m-CS/DDEAC aggregates could be used as curcumin carries, and achieved sustained release.

Layer-by-Layer Materials for the Fabrication of Devices with Electrochemical Applications

The construction of nanostructured materials for their application in electrochemical processes, e.g., energy storage and conversion, or sensing, has undergone a spectacular development over the last decades as a consequence of their unique properties in comparison to those of their bulk counterparts, e.g., large surface area and facilitated charge/mass transport pathways. This has driven strong research on the optimization of nanostructured materials for the fabrication of electrochemical devices, which demands techniques allowing the assembly of hybrid materials with well-controlled structures and properties. The Layer-by-Layer (LbL) method is well suited for fulfilling the requirements associated with the fabrication of devices for electrochemical applications, enabling the fabrication of nanomaterials with tunable properties that can be exploited as candidates for their application in fuel cells, batteries, electrochromic devices, solar cells, and sensors. This review provides an updated discussion of some of the most recent advances on the application of the LbL method for the fabrication of nanomaterials that can be exploited in the design of novel electrochemical devices.

Chitosan/Sodium Dodecyl Sulfate Complexes for Microencapsulation of Vitamin E and Its Release Profile-Understanding the Effect of Anionic Surfactant

Microencapsulation of bioactive substances is a common strategy for their protection and release rate control. The use of chitosan (Ch) is particularly promising due to its abundance, biocompatibility, and interaction with anionic surfactants to form complexes of different characteristics with relevance for use in microcapsule wall design. In this study, Ch/sodium dodecyl sulfate (SDS) microcapsules, without and with cross-linking agent (formaldehyde (FA) or glutaraldehyde (GA)), were obtained by the spray drying of vitamin E loaded oil-in-water emulsion. All of the microcapsules had good stability during the drying process. Depending on the composition, their product yield, moisture content, and encapsulation efficiency varied between 11-34%, 1.14-1.62%, and 94-126%, respectively. SEM and FTIR analysis results indicate that SDS as well as cross-linkers significantly affected the microcapsule wall properties. The profiles of in vitro vitamin E release from the investigated microcapsules fit with the Korsmeyer-Peppas model (r² > 0.9). The chemical structure of the anionic surfactant was found to have a significant effect on the vitamin E release mechanism. Ch/SDS coacervates may build a microcapsule wall without toxic crosslinkers. This enabled the combined diffusion/swelling based release mechanism of the encapsulated lipophilic substance, which can be considered favorable for utilization in food and pharmaceutical products.

Particle-laden fluid/fluid interfaces: physico-chemical foundations

Particle-laden fluid/fluid interfaces are ubiquitous in academia and industry, which has fostered extensive research efforts trying to disentangle the physico-chemical bases underlying the trapping of particles to fluid/fluid interfaces as well as the properties of the obtained layers. The understanding of such aspects is essential for exploiting the ability of particles on the stabilization of fluid/fluid interface for the fabrication of novel interface-dominated devices, ranging from traditional Pickering emulsions to more advanced reconfigurable devices. This review tries to provide a general perspective of the physico-chemical aspects associated with the stabilization of interfaces by colloidal particles, mainly chemical isotropic spherical colloids. Furthermore, some aspects related to the exploitation of particle-laden fluid/fluid interfaces on the stabilization of emulsions and foams will be also highlighted. It is expected that this review can be used for researchers and technologist as an initial approach to the study of particle-laden fluid layers.

Polyelectrolyte Multilayers on Soft Colloidal Nanosurfaces: A New Life for the Layer-By-Layer Method

The Layer-by-Layer (LbL) method is a well-established method for the assembly of nanomaterials with controlled structure and functionality through the alternate deposition onto a template of two mutual interacting molecules, e.g., polyelectrolytes bearing opposite charge. The current development of this methodology has allowed the fabrication of a broad range of systems by assembling different types of molecules onto substrates with different chemical nature, size, or shape, resulting in numerous applications for LbL systems. In particular, the use of soft colloidal nanosurfaces, including nanogels, vesicles, liposomes, micelles, and emulsion droplets as a template for the assembly of LbL materials has undergone a significant growth in recent years due to their potential impact on the design of platforms for the encapsulation and controlled release of active molecules. This review proposes an analysis of some of the current trends on the fabrication of LbL materials using soft colloidal nanosurfaces, including liposomes, emulsion droplets, or even cells, as templates. Furthermore, some fundamental aspects related to deposition methodologies commonly used for fabricating LbL materials on colloidal templates together with the most fundamental physicochemical aspects involved in the assembly of LbL materials will also be discussed.

Evaporation of Sessile Droplets of Polyelectrolyte/Surfactant Mixtures on Silicon Wafers

The wetting and evaporation behavior of droplets of aqueous solutions of mixtures of poly(diallyldimethylammonium chloride) solution, PDADMAC, with two different anionic surfactants, sodium laureth sulfate, SLES, and sodium N-lauroyl N-methyl taurate, SLMT, were studied in terms of the changes of the contact angle θ and contact length L of sessile droplets of the mixtures on silicon wafers at a temperature of 25 °C and different relative humidities in the range of 30–90%. The advancing contact angle θa was found to depend on the surfactant concentration, independent of the relative humidity, with the mixtures containing SLES presenting improved wetting behaviors. Furthermore, a constant droplet contact angle was not observed during evaporation due to pinning of the droplet at the coffee-ring that was formed. The kinetics for the first evaporation stage of the mixture were independent of the relative humidity, with the evaporation behavior being well described in terms of the universal law for evaporation.