Engineering cobalt oxide by interfaces and pore architectures for enhanced electrocatalytic performance for overall water splitting

Zinc oxide nanoflakes supported copper oxide nanosheets as a bifunctional electrocatalyst for OER and HER in an alkaline medium

Bifunctional electrocatalysts are the attractive research in the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) in the overall water-splitting reactions. The design and development of the cost-effective OER/HER bifunctional electrocatalysts with superior catalytic activity are still remaining as the big challenges. Herein, we have developed the CuO-ZnO nanocomposite as a bifunctional OER/HER electrocatalyst via simple chemical precipitation method. The nanocomposite was investigated for its crystalline structure, surface morphology and the functions of elements using XRD, FT-IR, SEM, TEM and XPS characterization techniques, respectively. The nanocomposite exhibited the excellent activity for the overall water-splitting in an alkaline medium. The CuO-ZnO nanocomposite showed the less onset potential of 1.4 and 0.15 V versus RHE in 1M KOH (Tafel slopes value of 0.180 and 0.400 V dec-1) for OER and HER, respectively. Hence, the as-prepared bifunctional electrocatalyst displayed the high stability for 10 h in the water electrolysis processes.

A stable N-doped NiMoO4/NiO2 electrocatalyst for efficient oxygen evolution reaction

Recently, there has been a significant interest in the study of highly active and stable transition metal-based electrocatalysts for the oxygen evolution reaction (OER). Non-noble metal nanocatalysts with excellent inherent activity, many exposed active centers, rapid electron transfer, and excellent structural stability are especially promising for the displacement of precious-metal catalysts for the production of sustainable and "clean" hydrogen gas through water-splitting. Herein, efficient electrocatalyst N-doped nickel molybdate nanorods were synthesized on Ni foam by a hydrothermal process and effortless chemical vapor deposition. The heterostructure interface of N-NiMoO4/NiO2 led to strong electronic interactions, which were beneficial for enhancing the OER activity of the catalyst. Excellent OER catalytic activity in 1.0 M KOH was shown, which offered a small overpotential of 185.6 mV to acquire a current density of 10 mA cm-2 (superior to the commercial benchmark material RuO2 under the same condition). This excellent electrocatalyst was stable for 90 h at a constant current density of 10 mA cm-2. We created an extremely reliable and effective OER electrocatalyst without the use of noble metals by doping a nonmetal element with nanostructured heterojunctions of various active components.

Novel mixed heterovalent (Mo/Co)Ox-zerovalent Cu system as bi-functional electrocatalyst for overall water splitting

A novel hybrid ternary metallic electrocatalyst of amorphous Mo/Co oxides and crystallized Cu metal was deposited over Ni foam using a one-pot, simple, and scalable solvothermal technique. The chemical structure of the prepared ternary electrocatalyst was systematically characterized and confirmed via XRD, FTIR, EDS, and XPS analysis techniques. FESEM images of (Mo/Co)Ox-Cu@NF display the formation of 3D hierarchical structure with a particle size range of 3-5 µm. The developed (Mo/Co)Ox-Cu@NF ternary electrocatalyst exhibits the maximum activity with 188 mV and 410 mV overpotentials at 50 mA cm-2 for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER), respectively. Electrochemical impedance spectroscopy (EIS) results for the (Mo/Co)Ox-Cu@NF sample demonstrate the minimum charge transfer resistance (Rct) and maximum constant phase element (CPE) values. A two-electrode cell based on the ternary electrocatalyst just needs a voltage of about 1.86 V at 50 mA cm-2 for overall water splitting (OWS). The electrocatalyst shows satisfactory durability during the OWS for 24 h at 10 mA cm-2 with an increase of only 33 mV in the cell potential.

Laser-Ironing Induced Capping Layer on Co-ZIF-L Promoting In Situ Surface Modification to High-Spin Oxide-Carbon Hybrids on the "Real Catalyst" for High OER Activity and Stability

Enhancing electrocatalytic performance through structural and compositional engineering attracts considerable attention. However, most materials only function as pre-catalysts and convert into "real catalysts" during electrochemical reactions. Such transition involves dramatic structural and compositional changes and disrupts their designed properties. Herein, for the first time, a laser-ironing (LI) approach capable of in-situ forming a laser-ironing capping layer (LICL) on the Co-ZIF-L flakes is developed. During the oxygen evolution reaction (OER) process, the LICL sustains the leaf-like morphology and promotes the formation of OER-active Co3 O4 nanoclusters with the highest activity and stability. In contrast, the pristine and conventional heat-treated Co-ZIF-Ls both collapse and transform to less active CoOOH. The density functional theory (DFT) calculations pinpoint the importance of the high spin (HS) states of Co ions and the narrowed band gap in Co3 O4 nanoclusters. They enhance the OER activity by promoting spin-selected electron transport, effectively lowering the energy barrier and realizing a spontaneous O2 -releasing step that is the potential determining step (pds) in CoOOH. This study presents an innovative approach for modulating both structural and compositional evolutions of electrocatalysts during the reaction, sustaining stability with high performance during dynamic electrochemical reactions, and providing new pathways for facile and high-precision surface microstructure control.

Insights on MOF-derived metal-carbon nanostructures for oxygen evolution

Electrochemical water splitting has been regarded a promising method for the production of green hydrogen, addressing the need for efficient energy conversion and storage. However, it is severely hindered by the oxygen evolution reaction (OER) because of its multi-step four-electron transfer pathway with sluggish reaction kinetics. Microporous metal-organic-frameworks (MOFs), by virtue of large specific surface area, high porosity, tunable composition and morphology, find widespread use as precursors of metal-carbon nanostructures. The resulting carbon nanomaterials can well inherit the characteristics and advantages of the crystalline MOF precursors, and exhibit versatile application prospects in the fields of environment and energy, particularly in OER. Herein, a meticulous overview of the synthesis strategy for MOF-derived metal-carbon nanostructures and the origins of their enhanced OER properties has been demonstrated. We comprehensively illustrate these aspects across three dimensions: MOF selection, metal introduction, and carbon structures. Finally, the challenges and future prospects for this emerging field will be presented.

Regulating the electronic structure of metal-organic frameworks via ion-exchanged Ir dispersion for robust overall water splitting

A facile ion exchange strategy to fabricate CoIrx-BDC with atomically dispersed Ir is developed towards overall water splitting. The optimized CoIr3-BDC requires only 12 and 81 mV to deliver 10 and 100 mA cm-2 alkaline HER, respectively, and only 245 mV to reach 100 mA cm-2 alkaline OER.

Rapid construction of Co/CoO/CoCH nanowire core/shell arrays for highly efficient hydrogen evolution reaction

The Co/CoO/CoCH (P-CoCH) nanowire core/shell arrays were prepared by a one step hydrothermal method and rapid reduction of cobalt carbonate hydroxide (CoCH) in Ar/H2 plasma for the first time. The rapid reduction process endows the P-CoCH with a unique porous structure, larger electrochemical active surface area and abundant activity sites. Therefore, the as-prepared P-CoCH nanowire core/shell arrays show superior HER performance with a low overpotential of 69 mV and a small Tafel slope of 47 mV dec-1 at a current density of 10 mA cm-2. In addition, the P-CoCH electrocatalyst demonstrates an excellent cycling stability without any obvious decay after 24 h continuous operation at 100 mA cm-2 current density. This study might provide a new insight into the rapidly construction of efficient HER Co-based electrocatalysts and beyond.

Controllable fabrication of iron-nickel alloy embedded in nitrogen-doped carbon for oxygen evolution

Nickel-based electrocatalysts for the oxygen evolution reaction (OER) show the disadvantages of low activity and poor stability. In this paper, an FeNi alloy is wrapped by an amino-modified MOF-5-derived N-doped carbon layer to address these problems. Additionally, the improvement resulting from Fe doping of NiOOH catalysts is theoretically supported.

POM@ZIF Derived Mixed Metal Oxide Catalysts for Sustained Electrocatalytic Oxygen Evolution

The design of efficient and stable oxygen evolution reaction (OER) catalysts based on noble-metal-free materials is crucial for energy conversion and storage. In this work, it was demonstrated how polyoxometalate (POM)-doped ZIF-67 can be converted into a stable oxygen evolution electrocatalyst by chemical etching, cation exchange, and thermal annealing steps. Characterization by X-ray photoelectron spectroscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy and Raman spectroscopy indicate that POM-doped ZIF-67 derived carbon-supported metal oxides were synthesized. The resulting composite shows structural and compositional advantages which lead to low overpotential (306 mV at j=10 mA ⋅ cm^-2 ) and long-term stability under harsh OER conditions (1.0 M aqueous KOH).

Tube-Sponge-Inspired Hierarchical Electrocatalysts with Boosted Mass and Electron Transfer for Efficient Oxygen Evolution

Hindered gas bubble release and limited electron conducting process represent the major bottlenecks for large-scale electrochemical water splitting. Both the desorption of bubbles and continuous electron transport are achievable on the surfaces of biomimetic catalytic materials by designing multiscale structural hierarchy. Inspired by the tubular structures of the deep-sea sponges, an exceptionally active and binder-free porous nickel tube arrays (PNTA) decorated with NiFe-Zn²⁺ -pore nanosheets (NiFe-P_Zn ) are fabricated. The PNTA facilitate removal of bubbles and electron transfer in the oxygen evolution reaction by reproducing trunks of the sponges, and simultaneously, the NiFe-P_Zn increase the number of catalytic active sites by simulating the sponge epidermis. With improved external mass transfer and interior electron transfer, the hierarchical NiFe-P_Zn @PNTA electrode exhibits superior oxygen evolution reaction performance with an overpotential of 172 mV at 10 mA cm^-2 (with a Tafel slope of 50 mV dec^-1 ). Furthermore, this electrocatalytic system recorded excellent reaction stability over 360 h with a constant current density of 100 mA cm^-2 at the potential of 1.52 V (versus RHE). This work provides a new strategy of designing hierarchical electrocatalysts for highly efficient water splitting.

MOF-Derived Cobalt@Mesoporous Carbon as Electrocatalysts for Oxygen Evolution Reaction: Impact of Organic Linker

Water electrolysis has attracted scientists' attention as a green route for energy generation. However, the sluggish kinetics of oxygen evolution reaction (OER) remarkably increases the reaction overpotential. In this work, we developed Co-based nanomaterials as cost-effective, highly efficient catalysts for OER. In this regard, different Co-based metal-organic frameworks (MOFs) were synthesized using different organic linkers. After annealing under inert atmosphere, the corresponding Co-embedded mesoporous carbon (Co/MC) materials were produced. Among them, Co/MC synthesized using 2-methyl imidazole (Co/NMC-2MeIM) expressed the highest surface area (412 m2/g) compared to its counterparts. Furthermore, it expressed a higher degree of defects as depicted by Raman spectra. Co/NMC-2MeIM exhibited the best catalytic performance toward OER in alkaline medium. It afforded an overpotential of 292 mV at a current density of 10 mA cm-2 and a Tafel slope of 99.2 mV dec-1. The superior electrocatalytic performance of Co/NMC-2MeIM is attributed to its high content of Co3+ on the surface, high surface area, and enhanced electrical conductivity induced by nitrogen doping. Furthermore, its high content of pyridinic-N and high degree of defects remarkably enhance the charge transfer between the adsorbed oxygen species and the active sites. These results may pave the avenue toward further investigation of metal/carbon materials in a wide range of electrocatalytic applications.

Layered Porous Graphitic Carbon Nitride Stabilized Effective Co2SnO4 Inverse Spinel as a Bifunctional Electrocatalyst for Overall Water Splitting

Developing an efficient, low-cost, and non-noble metal oxide-based nanohybrid material for overall water splitting is a highly desirable approach to promote clean energy harnessing and to minimize environmental issues. Accordingly, we proposed an interfacial engineering approach to construct layered porous graphitic carbon nitride (g-C₃N₄)-stabilized Co₂SnO₄ inverse spinel nanohybrid materials as highly active bifunctional electrocatalysts for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in an alkaline medium. Here, a Co₂SnO₄/g-C₃N₄ nanohybrid with a layered porous g-C₃N₄ stabilized cubelike inverse spinel has been synthesized with an enhanced surface area via a simple one-pot hydrothermal method. Besides, detailed structural and morphological characterizations were carried out using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission-scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HR-TEM), Fourier transform infrared (FT-IR), and Brunauer-Emmett-Teller (BET) analysis. Briefly, XPS analysis has revealed the existence of a strong coupling bond at the interface between a definite proportion of g-C₃N₄ nanosheets and the inverse spinel, which act as an electron transport channel to explore the exceptional performances for HER and OER. Compared to the Co₂SnO₄ inverse spinel lattice or g-C₃N₄ nanosheets, the prepared Co₂SnO₄/g-C₃N₄ nanohybrid-loaded 316 SSL mesh electrode showed excellent and stable electrocatalytic performances with very low overpotentials of 41 mV for HER and 260 mV for OER to reach the current density of 10 mA cm^-2. To understand the electrocatalytic phenomena, the faradic efficiency was calculated for the prepared bifunctional electrocatalyst as 96%, which effectively would favor water electrolysis. Accordingly, the Co₂SnO₄/g-C₃N₄ nanohybrid-loaded electrodes were constructed, and the minimum cell voltage was found to be 1.52 V to reach the current density of 10 mA cm^-2, which is comparable to the standard RuO₂∥Pt/C in two-electrode systems. Thus, the developed nanohybrid-based electrocatalyst could be an alternative to noble metal-centered systems for highly efficient overall water splitting.

MOF-Derived Ultrathin Cobalt Molybdenum Phosphide Nanosheets for Efficient Electrochemical Overall Water Splitting

The development of high-performance and cost-effective earth-abundant transition metal-based electrocatalysts is of major interest for several key energy technologies, including water splitting. Herein, we report the synthesis of ultrathin CoMoP nanosheets through a simple ion etching and phosphorization method. The obtained catalyst exhibits outstanding electrocatalytic activity and stability towards oxygen and hydrogen evolution reactions (OER and HER), with overpotentials down to 273 and 89 mV at 10 mA cm⁻², respectively. The produced CoMoP nanosheets are also characterized by very small Tafel slopes, 54.9 and 69.7 mV dec⁻¹ for OER and HER, respectively. When used as both cathode and anode electrocatalyst in the overall water splitting reaction, CoMoP-based cells require just 1.56 V to reach 10 mA cm⁻² in alkaline media. This outstanding performance is attributed to the proper composition, weak crystallinity and two-dimensional nanosheet structure of the electrocatalyst.

A Mild CO2 Etching Method To Tailor the Pore Structure of Platinum-Free Oxygen Reduction Catalysts in Proton Exchange Membrane Fuel Cells

The structural tailoring of pores is essential to high-performance Fe/N/C electrocatalysts for the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells. Current strategies for pore structure engineering are usually accompanied with a drastic change of the intrinsic activity-related surface, which may mask the real effects of the porous structure on ORR activity. Herein, a mild carbon dioxide (CO₂) etching method was used to flexibly tailor the pore structure of Fe/N/C electrocatalysts without drastic changes in their surface structure and property. In this way, via employing the Fe/N/C electrocatalysts as a model, the intrinsic impact of the pore structure on ORR activity was revealed. In addition, the CO₂ etching method developed a high-quality electrocatalyst (sample Fe/N/C-5% CO₂) with polarization performance exceeding that of the commercial Pt/C catalyst in the fuel cell working voltage region (>0.65 V). This work will promote the ongoing intensive studies on the rational design of the pore structures in the Fe/N/C electrocatalysts.

Designing of Highly Efficient Oxygen Evolution Reaction Electrocatalysts Utilizing A Correlation Factor: Theory and Experiment

The theoretical prediction of the catalytic activity is very beneficial for the design of highly efficient catalysts. At present, most theoretical descriptors focus on estimating the catalytic activity and understanding the enhancement mechanism of catalysts, while it is also quite important to find a factor to correlate the descriptors with preparation methods. In this work, a correlation factor, the d electron density of transition metal ions, was developed to correlate the d band center values of transition metal ions with the preparation methods of amorphization and Al introduction. According to the results of theoretical simulations, the correlation factor not only exhibited favorable linear relationships with the theoretical overpotentials of (CoFeAl_x)₃O₄ and (CoFeAl_x)₃O₄ + (CoFeAl_x)OOH systems but also correlated with two preparation methods by altering the volume of systems. Based on theoretical guidance, the electrocatalytic activities of the prepared (CoFeAl_x)₃O₄ specimens were gradually improved by the preparation methods of amorphization and Al introduction, and the Am-CoFeAl-2-10h specimen exhibited a low kinetic barrier of 268 mV, fast charge transfer rate, and stable electrocatalytic activity. This strategy could be applied to design highly efficient catalysts by adjusting the correlation factor of the active site with suitable preparation methods.

Hierarchical porous Ni, Fe-codoped Co-hydroxide arrays derived from metal–organic-frameworks for enhanced oxygen evolution

The multi metal organic frameworks can be successfully transformed into hierarchical porous Ni,Fe-codoped Co-hydroxide nanowire array catalysts with excellent electrocatalytic performance for the OER in alkaline media.

Selective Synthesis of Monodisperse CoO Nanooctahedra as Catalysts for Electrochemical Water Oxidation

Thermal decomposition is a promising route for the synthesis of metal oxide nanoparticles because size and morphology can be tuned by minute control of the reaction variables. We synthesized CoO nanooctahedra with diameters of ∼48 nm and a narrow size distribution. Full control over nanoparticle size and morphology could be obtained by controlling the reaction time, surfactant ratio, and reactant concentrations. We show that the particle size does not increase monotonically with time or surfactant concentration but passes through minima or maxima. We unravel the critical role of the surfactants in nucleation and growth and rationalize the observed experimental trends in accordance with simulation experiments. The as-synthesized CoO nanooctahedra exhibit superior electrocatalytic activity with long-term stability during oxygen evolution. The morphology of the CoO particles controls the electrocatalytic reaction through the distinct surface sites involved in the oxygen evolution reaction.

Boosting the electrocatalytic performance of NiFe layered double hydroxides for the oxygen evolution reaction by exposing the highly active edge plane (012)

The intrinsic activity of NiFe layer double hydroxides (LDHs) for the oxygen evolution reaction (OER) suffers from its predominantly exposed (003) basal plane, which is thought to have poor activity. Herein, we construct a hierarchal structure of NiFe LDH nanosheet-arrays-on-microplates (NiFe NSAs-MPs) to elevate the electrocatalytic activity of NiFe LDHs for the OER by exposing a high-activity plane, such as the (012) edge plane. It is surprising that the NiFe NSAs-MPs show activity of 100 mA cm-2 at an overpotential (η) of 250 mV, which is five times higher than that of (003) plane-dominated NiFe LDH microsheet arrays (NiFe MSAs) at the same η, representing the excellent electrocatalytic activity for the OER in alkaline media. Besides, we analyzed the OER activities of the (003) basal plane and the (012) and (110) edge planes of NiFe LDHs by density functional theory with on-site Coulomb interactions (DFT+U), and the calculation results indicated that the (012) edge plane exhibits the best catalytic performance among the various crystal planes because of the oxygen coordination of the Fe site, which is responsible for the high catalytic activity of NiFe NSAs-MPs.

Boosting Lattice Oxygen Oxidation of Perovskite to Efficiently Catalyze Oxygen Evolution Reaction by FeOOH Decoration

In the process of oxygen evolution reaction (OER) on perovskite, it is of great significance to accelerate the hindered lattice oxygen oxidation process to promote the slow kinetics of water oxidation. In this paper, a facile surface modification strategy of nanometer-scale iron oxyhydroxide (FeOOH) clusters depositing on the surface of LaNiO₃ (LNO) perovskite is reported, and it can obviously promote hydroxyl adsorption and weaken Ni-O bond of LNO. The above relevant evidences are well demonstrated by the experimental results and DFT calculations. The excellent hydroxyl adsorption ability of FeOOH-LaNiO₃ (Fe-LNO) can obviously optimize OH⁻ filling barriers to promote lattice oxygen-participated OER (LOER), and the weakened Ni-O bond of LNO perovskite can obviously reduce the reaction barrier of the lattice oxygen participation mechanism (LOM). Based on the above synergistic catalysis effect, the Fe-LNO catalyst exhibits a maximum factor of 5 catalytic activity increases for OER relative to the pristine perovskite and demonstrates the fast reaction kinetics (low Tafel slope of 42 mV dec⁻¹) and superior intrinsic activity (TOFs of ~40 O₂ S⁻¹ at 1.60 V vs. RHE).

Structural evolution from a fence-like to pillared-layer metal–organic framework for the stable oxygen evolution reaction

A porous fence-like MOF transforms into a dense pillared-layer coordination polymer, improving its chemical stability and exhibiting an excellent electrolytic OER performance.