Dual amplification for PEC ultrasensitive aptasensing of biomarker HER-2 based on Z-scheme UiO-66/CdIn2S4 heterojunction and flower-like PtPdCu nanozyme

As an important prognostic indicator in breast cancer, human epithelial growth factor receptor-2 (HER-2) is of importance for assessing prognosis of breast cancer patients, whose accurate and facile analysis are imperative in clinical diagnosis and treatment. Herein, photoactive Z-scheme UiO-66/CdIn2S4 heterojunction was constructed by a hydrothermal method, whose optical property and photoactivity were critically investigated by a range of techniques, combined by elucidating the interfacial charge transfer mechanism. Meanwhile, PtPdCu nanoflowers (NFs) were fabricated by a simple aqueous wet-chemical method, whose peroxidase (POD)-mimicking catalytic activity was scrutinized by representative tetramethylbenzidine (TMB) oxidation in H2O2 system. Taken together, the UiO-66/CdIn2S4 based photoelectrochemical (PEC) aptasensor was established for quantitative analysis of HER-2, where the detection signals were further magnified through catalytic precipitation reaction towards 4-chloro-1-naphthol (4-CN) oxidation (assisted by the PtPdCu NFs nanozyme). The PEC aptasensor presented a broader linear range within 0.1 pg mL-1-0.1 μg mL-1 and a lower limit of detection of 0.07 pg mL-1. This work developed a new PEC aptasensor for ultrasensitive determination of HER-2, holding substantial promise for clinical diagnostics.

Ultrafast synthesis of efficient TS-PtCoCu/CNTs composite with high feed-to-product conversion rate by Joule heating for electrocatalytic oxidation of ethanol

Due to the challenges involved in achieving high metal load, uniform metal dispersion and nanosized metal particles simultaneously, it is difficult to develop a simple protocol for the rapid and efficient synthesis of Pt-based composites for electrocatalytic ethanol oxidation reaction (EOR). In this study, a facile ultrafast thermal shock strategy via Joule heating was applied to fabricate a series of PtCoCu ternary nanoalloys decorated carbon nanotube composites (TS-PtCoCu/CNTs), without the need for a reducing agent or surfactant. The TS-PtCoCu/CNTs with optimal Pt content (∼15 %) exhibited excellent EOR activity, with mass and specific activity of 3.58 A mgPt-1 and 5.79 mA cm-2, respectively, which are 3.8 and 13.5 times higher than those of Pt/C. Compared with the control prepared through the traditional furnace annealing, the catalyst also showed excellent activity and stability. DFT calculations revealed that the TS-PtCoCu/CNTs possesses a downshifted d-band center, weakened CO adsorption and higher OH affinity compared with monometallic Pt, all of which lead to the preferred C1 pathway for EOR. This study demonstrates an ultrafast construction of a highly efficient Pt-Co-Cu ternary catalyst for EOR. Additionally, it provides insights into the reaction mechanism based on structural characterization, electrochemical characterization, and theoretical calculations.

One-pot synthesis of ultrafine trimetallic PtPdCu alloy nanoparticles decorated on carbon nanotubes for bifunctional catalysis of ethanol oxidation and oxygen reduction

Bifunctional catalysts for ethanol oxidation reaction (EOR) and oxygen reduction reaction (ORR) with high noble-metal utilization are highly beneficial to direct ethanol fuel cells (DEFCs). This study developed a ternary bifunctional catalyst composed of ultrafine PtPdCu alloy nanoparticles and carbon nanotubes (CNTs) support through a facile surfactant-free solvothermal route. The carboxyl terminal groups on CNTs ensure the confined growth of PtPdCu alloys (∼5 nm) and suppress Ostwald ripening of metallic active sites during electrochemical cycling. Consequently, PtPdCu/CNTs exhibits high mass activity (1.95 A mg^-1) and specific activity (4.08 mA cm^-2) toward EOR, which are 7.8 and 8.9 times higher, respectively, than those of commercial Pt/C. Furthermore, PtPdCu/CNTs displays superior stability toward EOR compared with its bimetallic counterparts (PtPd/CNTs and PtCu/CNTs). In addition, PtPdCu/CNTs exhibits the highest half-wave potential of 0.888 V among all electrocatalysts, indicating high ORR activity. Density functional theory calculations reveal that Pd and Cu mediate the electronic structure of Pt, leading to enhanced catalytic activity of PtPdCu/CNTs. The excellent catalytic property of PtPdCu/CNTs can also be attributed to the bifunctional effects of Pd/Cu and the interaction between metal and the carbon support. The proposed material is a contribution to the family of efficient ternary-alloy electrocatalysts for fuel cells.

Modification of multi-walled carbon nanotubes with platinum-osmium to develop stable catalysts for direct methanol fuel cells

In the study, a new bimetallic catalyst was synthesized for methanol oxidation using multi-walled carbon nanotube (MWCNT)-supported platinum-osmium (PtOs) nanoparticles (PtOs@MWCNT NPs). The morphological structures of the prepared NPs were examined using different techniques, such as scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrochemical characterization of the synthesized PtOs@MWCNT catalysts, such as chronoamperometry (CA), cyclic voltammetry (CV), scan rate (SR) analysis, cyclic catalytic test, and electrochemical surface area (ECSA) evaluation, were performed in an alkaline medium. From the results obtained, the size of the NPs was found to be 3.12 nm according to the Debye-Schrrer equation, and the MWCNTs were clearly observed by SEM imaging. After the characterization of the prepared nanomaterials, the PtOs@MWCNT catalysts were employed in the methanol oxidation reaction, and a high oxidation current value of 220.86 mA cm^-2 was observed. Besides, according to the CA results, the catalyst exhibited high stability for 4000 s, and it was seen that Os metal improved the catalytic activity of the main catalyst. These results show that the PtOs@MWCNT catalyst is highly stable and reusable, and provides high electrocatalytic activity in the methanol oxidation reaction. Moreover, the obtained catalyst gave ideal results in terms of CO tolerance and activity. These data show that the obtained catalyst will provide significant improvement and superior efficiency in fuel-cell applications.