Droplet-based nanogenerators for energy harvesting and self-powered sensing

Triboelectric nanogenerators with groove textures and carbon fillers for self-powered cathodic protection

Contact-separation mode triboelectric nanogenerators (CS-TENG) have received widespread attention in self-powered cathodic corrosion protection, but their relatively low output limits the application. This paper introduced both groove textures and carbon-fillers into CS-TENG and investigated the influences and mechanism of textures and filler parameters on the output of CS-TENG. Through the external connection to the protected metal, the CS-TENG with optimal textures and fillers established the power supply of the self-powered cathodic protection. It is shown that for CS-TENG with groove textures, a texture size of 10 μm-10 μm exhibits the maximum lateral deformation, which generates the largest contact area and lateral deformation, and thus outputs the highest voltage. Among the three selected carbon-fillers (carbon fibers, hard carbon particles, graphene oxide), carbon fibers with 0.5 wt% mass fraction provide the highest charge storage capacity and thus the largest electrical output. Compared to the CS-TENG without textures and fillers, the open-circuit voltage of CS-TENG with optimal textures and fillers increased by 165.08%. Cathode anti-corrosion experiments and EIS (electrochemical impedance spectroscopy) tests indicate that CS-TENG with optimal textures and fillers significantly reduce the electron transfer rate on the metal surface, exhibiting excellent anti-corrosion performance.

Electrochemical kinetic energy harvesting mediated by ion solvation switching in two-immiscible liquid electrolyte

Kinetic energy harvesting has significant potential, but current methods, such as friction and deformation-based systems, require high-frequency inputs and highly durable materials. We report an electrochemical system using a two-phase immiscible liquid electrolyte and Prussian blue analogue electrodes for harvesting low-frequency kinetic energy. This system converts translational kinetic energy from the displacement of electrodes between electrolyte phases into electrical energy, achieving a peak power of 6.4 ± 0.08 μW cm-2, with a peak voltage of 96 mV and peak current density of 183 μA cm-2 using a 300 Ω load. This load is several thousand times smaller than those typically employed in conventional methods. The charge density reaches 2.73 mC cm-2, while the energy density is 116 μJ cm-2 during a harvesting cycle. Also, the system provides a continuous current flow of approximately 5 μA cm-2 at 0.005 Hz for 23 cycles without performance decay. The driving force behind voltage generation is the difference in solvation Gibbs free energy between the two electrolyte phases. Additionally, we demonstrate the system's functionality in a microfluidic harvester, generating a maximum power density of 200 nW cm-2 by converting the kinetic energy to propel the electrolyte through the microfluidic channel into electricity.

Optimizing Droplet-Based Electricity Generator via a Low Sticky Hydrophobic Droplet-Impacted Surface

Droplet-based electricity generators (DEGs) are increasingly recognized for their potential in converting renewable energy sources. This study explores the interplay of surface hydrophobicity and stickiness in improving DEG efficiency. It find that the high-performance C-WaxDEGs leverage both these properties. Specifically, DEGs incorporating polydimethylsiloxane (PDMS) with carnauba wax (C-wax) exhibit increased output as surface stickiness decreases. Through experimental comparisons, PDMS with 1wt.% C-wax demonstrated a significant power output increase from 0.07 to 1.2 W m- 2, which attribute to the minimized adhesion between water molecules and the polymer surface, achieved by embedding C-wax into PDMS surface to form microstructures. This improvement in DEG performance is notable even among samples with similar surface potentials and contact angles, suggesting that C-wax's primary contribution is in reducing surface stickiness rather than altering other surface properties. The further investigations into the C-WaxDEG variant with 1wt.% C-wax PDMS uncover its potential as a sensor for water quality parameters such as temperature, pH, and heavy metal ion concentration. These findings open avenues for the integration of C-WaxDEGs into flexible electronic devices aimed at environmental monitoring.

Piezoelectric nanogenerators from sustainable biowaste source: Power harvesting and respiratory monitoring with electrospun crab shell powder-poly(vinylidene fluoride) composite nanofibers

Wearable piezoelectric nanogenerators (PENGs) are increasingly significant in healthcare and energy harvesting applications due to their ability to convert mechanical energy into electrical signals. In this study, we developed PENGs by incorporating crab shell powder (CS-NFs) into electrospun polyvinylidene fluoride (PVDF) nanofibers to enhance their piezoelectric properties. The PVDF-CS-NFs (PC-NFs) composites were evaluated for structural, thermal, and piezoelectric performance. The 1.5 wt% CS-NFs composite exhibited a notable improvement, with a maximum output voltage of 19 V under mechanical deformation, significantly higher than pristine PVDF NFs. Furthermore, the device demonstrated excellent sensitivity in real-time respiratory monitoring when applied to various body locations, including the chest, throat, and mask. Additionally, the PC-NFs-based PENGs were capable of charging a 2.2 µF capacitor to 2 V within 180 s and powering 56 LEDs. These results underscore the potential of using sustainable crab shell waste in biocompatible, eco-friendly piezoelectric devices for wearable sensors and energy harvesting applications.

Bionic e-skin with precise multi-directional droplet sliding sensing for enhanced robotic perception

Electronic skins with deep and comprehensive liquid information detection are desired to endow intelligent robotic devices with augmented perception and autonomous regulation in common droplet environments. At present, one technical limitation of electronic skins is the inability to perceive the liquid sliding information as realistically as humans and give feedback in time. To this critical challenge, in this work, a self-powered bionic droplet electronic skin is proposed by constructing an ingenious co-layer interlaced electrode network and using an overpass connection method. The bionic skin is used for droplet environment reconnaissance and converts various dynamic droplet sliding behaviors into electrical signals based on triboelectricity. More importantly, the two-dimensional sliding behavior of liquid droplets is comprehensively perceived by the e-skin and visually fed back in real-time on an indicator. Furthermore, the flow direction warning and intelligent closed-loop control of water leakage are also achieved by this e-skin, achieving the effect of human neuromodulation. This strategy compensates for the limitations of e-skin sensing droplets and greatly narrows the gap between artificial e-skins and human skins in perceiving functions.

Elastic Droplet-Based Magnetoelectric Generator for High-performance Energy Collection

Conventional magnetoelectric generators are regarded as effective devices for harvesting concentrated hydraulic power but are ineffective for dispersed hydropower (e.g., raindrops) due to their bulkiness and immobility. Here, we propose a superhydrophobic magnetoelectric generator (MSMEG) based on an elastic magnetic film that can efficiently convert the energy of lightweight water droplets into electricity. The MSMEG consists of five parts: a superhydrophobic magnetic material-based film (SMMF), a coil, a NdFeB magnet, an acrylic housing, and an expandable polystyrene (EPS) base. The SMMF with coil can deform/recover when droplets impact/leave the MSMEG, resulting in a peak current, peak charge density, and peak power density of ∼13.02 mA, ∼1826.5 mC/m2, and ∼1413.0 mW/m2, respectively, with a load resistance of 47 Ω. Related working mechanism is analyzed through Maxwell numerical simulation, which is used for further guidance on increasing the electrical output of the MSMEG. Furthermore, the MSMEG can quickly charge a commercial capacitor with 2.7 V/1 F to 1.18 V within 200 s and power diverse electronic devices (e.g., light emitting diodes (LEDs), fans) with constant excitation by water droplets. We believe that such an MSMEG is expected to provide a promising strategy for efficiently harvesting dispersed raindrop energy.

PVDF-HFP encapsulated WS2nanosheets in droplet-based triboelectric nanogenerators for possible detection of human Na+/K+ion concentration

Here we report the liquid-solid interaction in droplet-based triboelectric nanogenerators (TENG) for estimation of human Na+/K+levels. The exploitation of PVDF-HFP encapsulated WS2as active layer in the droplet-based TENG (DTENG) leads to the generation of electrical signal during the impact of water droplet. Comparison over the control devices indicates that surface quality and dielectric nature of the PVDF-HFP/WS2composite largely dictates the performance of the DTENG. The demonstration of excellent sensitivity of the DTENG towards water quality indicates its promising application towards water testing. In addition, the alteration in output signal with slightest variation in ionic concentration (Na+or K+) in water has been witnessed and is interpreted with charge transfer and ion transfer processes during liquid-solid interaction. The study reveals that the ion mobility largely affects the ion adsorption process on the active layer of PVDF-HFP/WS2and thus generates distinct output profiles for diverse ions like Na+and K+. Following that, the DTENG characteristics have been exploited to artificial urine where the varying output signals have been recorded for variation in urinary Na+ion concentration. Therefore, the deployment of PVDF-HFP/WS2in DTENG holds promising application towards the analyse of ionic characteristics of body fluids.

A robust thin-film droplet-induced electricity generator

The pursuit of cost-effective, high-voltage electricity generators activated by droplets represents a new frontier in hydropower technology. This study presents an economical method for crafting droplet generators using common materials such as solid polytetrafluoroethylene (PTFE) films and readily available tapes, eliminating the need for specialized cleanroom facilities. A thorough investigation into voltage-limiting factors, encompassing device capacitance and induced electrode charges, reveals specific areas with potential for optimization. A substantial enhancement in the open-circuit voltage (Voc) was achieved, reaching approximately 282.2 ± 27.9 V-an impressive increase of around 60 V compared to earlier benchmarks. One device showcased its capability to power 100 LEDs concurrently, underscoring its efficacy. Ten such devices created diverse luminous patterns with uniform light intensity for each LED, showcasing the practical potential of the approach. The methodology's cost-effectiveness results in a remarkable cost reduction compared to solution-based materials, paving the way for the widespread adoption of large-scale water droplet energy harvesting.

The emerging chemistry of self-electrified water interfaces

Water is known for dissipating electrostatic charges, but it is also a universal agent of matter electrification, creating charged domains in any material contacting or containing it. This new role of water was discovered during the current century. It is proven in a fast-growing number of publications reporting direct experimental measurements of excess charge and electric potential. It is indirectly verified by its success in explaining surprising phenomena in chemical synthesis, electric power generation, metastability, and phase transition kinetics. Additionally, electrification by water is opening the way for developing green technologies that are fully compatible with the environment and have great potential to contribute to sustainability. Electrification by water shows that polyphasic matter is a charge mosaic, converging with the Maxwell-Wagner-Sillars effect, which was discovered one century ago but is still often ignored. Electrified sites in a real system are niches showing various local electrochemical potentials for the charged species. Thus, the electrified mosaics display variable chemical reactivity and mass transfer patterns. Water contributes to interfacial electrification from its singular structural, electric, mixing, adsorption, and absorption properties. A long list of previously unexpected consequences of interfacial electrification includes: "on-water" reactions of chemicals dispersed in water that defy current chemical wisdom; reactions in electrified water microdroplets that do not occur in bulk water, transforming the droplets in microreactors; and lowered surface tension of water, modifying wetting, spreading, adhesion, cohesion, and other properties of matter. Asymmetric capacitors charged by moisture and water are now promising alternative equipment for simultaneously producing electric power and green hydrogen, requiring only ambient thermal energy. Changing surface tension by interfacial electrification also modifies phase-change kinetics, eliminating metastability that is the root of catastrophic electric discharges and destructive explosions. It also changes crystal habits, producing needles and dendrites that shorten battery life. These recent findings derive from a single factor, water's ability to electrify matter, touching on the most relevant aspects of chemistry. They create tremendous scientific opportunities to understand the matter better, and a new chemistry based on electrified interfaces is now emerging.

A shadow enabled non-invasive probe for multi-feature intelligent liquid surveillance system

Liquid detection probes used to identify the features of liquids show great promise in a variety of important applications. However, some challenges, such as sample contamination by direct contact with the liquid, the requirement of additional signal emitters, and complex fabrication, hindered the development of liquid detection probes. Here, we developed a non-invasive shadow probe (SP) for a multi-feature intelligent liquid surveillance system (ILSS). The self-powered SP with the working mechanism of the shadow effect can detect the features of liquids by analyzing the variations of liquid shadows such as the area, wavelength, and brightness. The exact resolution (5 different colors, 6 different concentrations, 6 different levels, 100% accuracy) and fast response time (0.2 ms) are shown by the SP under ambient light conditions (even in 0.003 sun). The ILSS, which integrated the SPs with signal processing circuits and applied the artificial intelligence (AI) technique, successfully detects and synoptically learns about liquids simultaneously. The in-real time ILSS reaches a test accuracy of 99.3% for 10 types of liquids with multiple features. This work showcases a promising solution for non-invasive multi-feature liquid detection, displaying great potential for future applications.

Recent Advances in Triboelectric Nanogenerators: From Technological Progress to Commercial Applications

Serious climate changes and energy-related environmental problems are currently critical issues in the world. In order to reduce carbon emissions and save our environment, renewable energy harvesting technologies will serve as a key solution in the near future. Among them, triboelectric nanogenerators (TENGs), which is one of the most promising mechanical energy harvesters by means of contact electrification phenomenon, are explosively developing due to abundant wasting mechanical energy sources and a number of superior advantages in a wide availability and selection of materials, relatively simple device configurations, and low-cost processing. Significant experimental and theoretical efforts have been achieved toward understanding fundamental behaviors and a wide range of demonstrations since its report in 2012. As a result, considerable technological advancement has been exhibited and it advances the timeline of achievement in the proposed roadmap. Now, the technology has reached the stage of prototype development with verification of performance beyond the lab scale environment toward its commercialization. In this review, distinguished authors in the world worked together to summarize the state of the art in theory, materials, devices, systems, circuits, and applications in TENG fields. The great research achievements of researchers in this field around the world over the past decade are expected to play a major role in coming to fruition of unexpectedly accelerated technological advances over the next decade.

A self-powered wearable brain-machine-interface system for ceasing action

A self-powered wearable brain-machine-interface system with pulse detection and brain stimulation for ceasing action has been realized. The system is composed of (1) a power supply unit that employs a piezoelectric generator and converts the mechanical energy of human daily activities into electricity; (2) a neck pulse biosensor that allows continuous measurements of carotid pulse by using a piezoelectric polyvinylidene fluoride film; (3) a data analysis module that enables a coordinated brain-machine-interface system to output brain stimulation signals; and (4) brain stimulating electrodes linked to the brain that implement behavioral intervention. Demonstration of the system with stimulating electrodes implanted in the periaqueductal gray (PAG) in running mice reveals the great effect of forced ceasing action. The mice stop their running within several seconds when the stimulation signals are sent into the PAG brain region (inducing fear). This self-powered scheme for neural stimulation realizes specific behavioral intervention without any external power supply, thus providing a new concept for future behavior intervention.