Understanding 3D TSE Sequences: Advantages, Disadvantages, and Application in MSK Imaging

Feasibility of deep learning-reconstructed thin-slice single-breath-hold HASTE for detecting pancreatic lesions: A comparison with two conventional T2-weighted imaging sequences

Objective

The objective of this study was to evaluate the clinical feasibility of deep learning reconstruction-accelerated thin-slice single-breath-hold half-Fourier single-shot turbo spin echo imaging (HASTEDL) for detecting pancreatic lesions, in comparison with two conventional T2-weighted imaging sequences: compressed-sensing HASTE (HASTECS) and BLADE.

Methods

From March 2022 to January 2023, a total of 63 patients with suspected pancreatic-related disease underwent the HASTEDL, HASTECS, and BLADE sequences were enrolled in this retrospectively study. The acquisition time, the pancreatic lesion conspicuity (LCP), respiratory motion artifact (RMA), main pancreatic duct conspicuity (MPDC), overall image quality (OIQ), signal-to-noise ratio (SNR), and contrast-noise-ratio (CNR) of the pancreatic lesions were compared among the three sequences by two readers.

Results

The acquisition time of both HASTEDL and HASTECS was 16 s, which was significantly shorter than that of 102 s for BLADE. In terms of qualitative parameters, Reader 1 and Reader 2 assigned significantly higher scores to the LCP, RMA, MPDC, and OIQ for HASTEDL compared to HASTECS and BLADE sequences; As for the quantitative parameters, the SNR values of the pancreatic head, body, tail, and lesions, the CNR of the pancreatic lesion measured by the two readers were also significantly higher for HASTEDL than for HASTECS and BLADE sequences.

Conclusions

Compared to conventional T2WI sequences (HASTECS and BLADE), deep-learning reconstructed HASTE enables thin slice and single-breath-hold acquisition with clinical acceptable image quality for detection of pancreatic lesions.

Morphological assessment of cartilage and osteoarthritis in clinical practice and research: Intermediate-weighted fat-suppressed sequences and beyond

Magnetic resonance imaging (MRI) is widely regarded as the primary modality for the morphological assessment of cartilage and all other joint tissues involved in osteoarthritis. 2D fast spin echo fat-suppressed intermediate-weighted (FSE FS IW) sequences with a TE between 30 and 40ms have stood the test of time and are considered the cornerstone of MRI protocols for clinical practice and trials. These sequences offer a good balance between sensitivity and specificity and provide appropriate contrast and signal within the cartilage as well as between cartilage, articular fluid, and subchondral bone. Additionally, FS IW sequences enable the evaluation of menisci, ligaments, synovitis/effusion, and bone marrow edema-like signal changes. This review article provides a rationale for the use of FSE FS IW sequences in the morphological assessment of cartilage and osteoarthritis, along with a brief overview of other clinically available sequences for this indication. Additionally, the article highlights ongoing research efforts aimed at improving FSE FS IW sequences through 3D acquisitions with enhanced resolution, shortened examination times, and exploring the potential benefits of different magnetic field strengths. While most of the literature on cartilage imaging focuses on the knee, the concepts presented here are applicable to all joints. KEY POINTS: 1. MRI is currently considered the modality of reference for a "whole-joint" morphological assessment of osteoarthritis. 2. Fat-suppressed intermediate-weighted sequences remain the keystone of MRI protocols for the assessment of cartilage morphology, as well as other structures involved in osteoarthritis. 3. Trends for further development in the field of cartilage and joint imaging include 3D FSE imaging, faster acquisition including AI-based acceleration, and synthetic imaging providing multi-contrast sequences.

Usefulness of T2-Weighted Images with Deep-Learning-Based Reconstruction in Nasal Cartilage

OBJECTIVE

This study aims to evaluate the feasibility of visualizing nasal cartilage using deep-learning-based reconstruction (DLR) fast spin-echo (FSE) imaging in comparison to three-dimensional fast spoiled gradient-echo (3D FSPGR) images.

MATERIALS AND METHODS

This retrospective study included 190 set images of 38 participants, including axial T1- and T2-weighted FSE images using DLR (T1WIDL and T2WIDL, belong to FSEDL) and without using DLR (T1WIO and T2WIO, belong to FSEO) and 3D FSPGR images. Subjective evaluation (overall image quality, noise, contrast, artifacts, and identification of anatomical structures) was independently conducted by two radiologists. Objective evaluation including signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) was conducted using manual region-of-interest (ROI)-based analysis. Coefficient of variation (CV) and Bland-Altman plots were used to demonstrate the intra-rater repeatability of measurements for cartilage thickness on five different images.

RESULTS

Both qualitative and quantitative results confirmed superior FSEDL to 3D FSPGR images (both p < 0.05), improving the diagnosis confidence of the observers. Lower lateral cartilage (LLC), upper lateral cartilage (ULC), and septal cartilage (SP) were relatively well delineated on the T2WIDL, while 3D FSPGR showed poorly on the septal cartilage. For the repeatability of cartilage thickness measurements, T2WIDL showed the highest intra-observer (%CV = 8.7% for SP, 9.5% for ULC, and 9.7% for LLC) agreements. In addition, the acquisition time for T1WIDL and T2WIDL was respectively reduced by 14.2% to 29% compared to 3D FSPGR (both p < 0.05).

CONCLUSIONS

Two-dimensional equivalent-thin-slice T1- and T2-weighted images using DLR showed better image quality and shorter scan time than 3D FSPGR and conventional construction images in nasal cartilages. The anatomical details were preserved without losing clinical performance on diagnosis and prognosis, especially for pre-rhinoplasty planning.

Rapid lumbar MRI protocol using 3D imaging and deep learning reconstruction

BACKGROUND AND PURPOSE

Three-dimensional (3D) imaging of the spine, augmented with AI-enabled image enhancement and denoising, has the potential to reduce imaging times without compromising image quality or diagnostic performance. This work evaluates the time savings afforded by a novel, rapid lumbar spine MRI protocol as well as image quality and diagnostic differences stemming from the use of an AI-enhanced 3D T2 sequence combined with a single Dixon acquisition.

MATERIALS AND METHODS

Thirty-five subjects underwent MRI using standard 2D lumbar imaging in addition to a "rapid protocol" consisting of 3D imaging, enhanced and denoised using a prototype DL reconstruction algorithm as well as a two-point Dixon sequence. Images were graded by subspecialized radiologists and imaging times were collected. Comparison was made between 2D sagittal T1 and Dixon fat images for neural foraminal stenosis, intraosseous lesions, and fracture detection.

RESULTS

This study demonstrated a 54% reduction in total acquisition time of a 3D AI-enhanced imaging lumbar spine MRI rapid protocol combined with a sagittal 2D Dixon sequence, compared to a 2D standard-of-care protocol. The rapid protocol also demonstrated strong agreement with the standard-of-care protocol with respect to osseous lesions (κ = 0.88), fracture detection (κ = 0.96), and neural foraminal stenosis (ICC > 0.9 at all levels).

CONCLUSION

3D imaging of the lumbar spine with AI-enhanced DL reconstruction and Dixon imaging demonstrated a significant reduction in imaging time with similar performance for common diagnostic metrics. Although previously limited by long postprocessing times, this technique has the potential to enhance patient throughput in busy radiology practices while providing similar or improved image quality.

MRI evaluation of soft tissue tumors: comparison of a fast, isotropic, 3D T2-weighted fat-saturated sequence with a conventional 2D T2-weighted fat-saturated sequence for tumor characteristics, resolution, and acquisition time

OBJECTIVES

To test whether a 4-fold accelerated 3D T2-weighted (T2) CAIPIRINHA SPACE TSE sequence with isotropic voxel size is equivalent to conventional 2DT2 TSE for the evaluation of intrinsic and perilesional soft tissue tumors (STT) characteristics.

METHODS

For 108 patients with histologically-proven STTs, MRI, including 3DT2 (CAIPIRINHA SPACE TSE) and 2DT2 (TSE) sequences, was performed. Two radiologists evaluated each sequence for quality (diagnostic, non-diagnostic), tumor characteristics (heterogeneity, signal intensity, margin), and the presence or absence of cortical involvement, marrow edema, and perilesional edema (PLE); tumor size and PLE extent were measured. Signal-to-noise (SNR) and contrast-to-noise (CNR) ratios and acquisition times for 2DT2 in two planes and 3DT2 sequences were reported. Descriptive statistics and inter-method agreement were reported.

RESULTS

Image quality was diagnostic for all sequences (100% [108/108]). No difference was observed between 3DT2 and 2DT2 tumor characteristics (p < 0.05). There was no difference in mean tumor size (3DT2: 2.9 ± 2.5 cm, 2DT2: 2.8 ± 2.6 cm, p = 0.4) or PLE extent (3DT2:0.5 ± 1.2 cm, 2DT2:0.5 ± 1.0 cm, p = 0.9) between the sequences. There was no difference in the SNR of tumors, marrow, and fat between the sequences, whereas the SNR of muscle was higher (p < 0.05) on 3DT2 than 2DT2. CNR measures on 3DT2 were similar to 2DT2 (p > 0.1). The average acquisition time was shorter for 3DT2 compared with 2DT2 (343 ± 127 s vs 475 ± 162 s, respectively).

CONCLUSION

Isotropic 3DT2 MRI offers higher spatial resolution, faster acquisition times, and equivalent assessments of STT characteristics compared to conventional 2DT2 MRI in two planes. 3DT2 is interchangeable with a 2DT2 sequence in tumor protocols.

KEY POINTS

• Isotropic 3DT2 CAIPIRINHA SPACE TSE offers higher spatial resolution than 2DT2 TSE and is equivalent to 2DT2 TSE for assessments of soft tissue tumor intrinsic and perilesional characteristics. • Multiplanar reformats of 3DT2 CAIPIRINHA SPACE TSE can substitute for 2DT2 TSE acquired in multiple planes, thereby reducing the acquisition time of MRI tumor protocols. • 3DT2 CAIPIRINHA SPACE TSE and 2DT2 TSE had similar CNR of tissues.

Comparison between T2-weighted two-dimensional and three-dimensional fast spin-echo MRI sequences for characterizing thoracolumbar intervertebral disc disease in small-breed dogs

Magnetic resonance imaging (MRI) is a standard test for diagnosis and treatment planning in dogs with degenerative thoracolumbar intervertebral disc disease (IVDD). However, published studies evaluating three-dimensional fast-spin echo (3D-FSE) pulse sequences for dogs with IVDD are currently limited. Aims of this retrospective, observational study were to compare findings from T2-weighted two- and three-dimensional fast spin-echo sequences (2D- and 3D-FSE, respectively) for a group of small breed dogs with thoracolumbar IVDD. Inclusion criteria were dogs with IVDD that underwent 1.5-Tesla MRI using both 2D-FSE and 3D-FSE sequences. For each dog and sequence, five pathologic indices were recorded: epidural fat discontinuation, vertebral canal compromise, spinal cord signal change, disc degeneration, and nerve root compression. Two independent investigators also scored visibility of the facet joint, intervertebral foramen, nerve roots, spinal cord grey-white matter differentiation, intervertebral discs, and epidural fat. The Wilcoxon signed-rank test was used to evaluate the between-sequence differences in pathologic indices and visibility scores. Interobserver agreement was measured using Cohen's weighted kappa along with 95% confidence intervals. A total of 21 dogs were sampled. The 3D-FSE sequences had higher pathologic indices of vertebral canal compromise (P = 0.020) and spinal cord signal change (P = 0.046) than 2D-FSE sequences. Furthermore, 3D-FSE sequences had higher visibility scores for the facet joint, intervertebral foramen, and nerve root structures (P < 0.001). Findings from the current supported the use of 3D-FSE sequences over 2D-FSE sequences for the evaluation of IVDD and visualization of spinal structures in small breed dogs.

High-Resolution Simultaneous Multi-Slice Accelerated Turbo Spin-Echo Musculoskeletal Imaging: A Head-to-Head Comparison With Routine Turbo Spin-Echo Imaging

Background/Aim: The turbo spin-echo (TSE) sequence is widely used for musculoskeletal (MSK) imaging; however, its acquisition speed is limited and can be easily affected by motion artifacts. We aimed to evaluate whether the use of a simultaneous multi-slice TSE (SMS-TSE) sequence can accelerate MSK imaging while maintaining image quality when compared with the routine TSE sequence.

Methods: We prospectively enrolled 71 patients [mean age, 37.43 ± 12.56 (range, 20–67) years], including 37 men and 34 women, to undergo TSE and SMS sequences. The total scanning times for the wrist, ankle and knee joint with routine sequence were 14.92, 13.97, and 13.48 min, respectively. For the SMS-TSE sequence, they were 7.52, 7.20, and 6.87 min. Quantitative parameters, including the signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR), were measured. Three experienced MSK imaging radiologists qualitatively evaluated the image quality of bone texture, cartilage, tendons, ligament, meniscus, and artifact using a 5-point evaluation system, and the diagnostic performance of the SMS-TSE sequences was evaluated.

Results: Compared with the routine TSE sequences, the scanning time was lower by 49.60, 48.46, and 49.04% using SMS-TSE sequences for the wrist, ankle, and knee joints, respectively. For the SNR comparison, the SMS-TSE sequences were significantly higher than the routine TSE sequence for wrist (except for Axial-T2WI-FS), ankle, and knee joint MR imaging (all p < 0.05), but no statistical significance was obtained for the CNR measurement (all p > 0.05, except for Sag-PDWI-FS in ankle joint). For the wrist joint, the diagnostic sensitivity, specificity, and accuracy were 88.24, 100, and 92%. For the ankle joint, they were 100, 75, and 93.33%. For the knee joint, they were 87.50, 85.71, and 87.10%.

Conclusion: The use of the SMS-TSE sequence in the wrist, ankle, and knee joints can significantly reduce the scanning time and show similar image quality when compared with the routine TSE sequence.

Comparing the Efficacy of True-Volume Analysis Using Magnetic Resonance Imaging With Computerized Tomography and Conventional Methods of Evaluation in Cystic Osteochondral Lesions of the Talus: A Pilot Study

Background: Osteochondral lesions of the talus (OLT) often require advanced imaging if they prove to be refractory to preliminary microfracture. Orthopedic surgeons may misinterpret the size and morphology of the OLT when evaluating through conventional methods. The purpose of this study was to evaluate MRI as a modality for calculating true-volumes and compare its utility to that of CT true-volume and conventional methods of measuring lesion size.

METHODS

With IRB approval, an institutional radiology database was queried for patients with cystic OLT that had undergone and failed microfracture and had compatible CT and MR scans between 2011 and 2016. Five lesions, previously analyzed and described in the literature using CT true-volume, were selected. 10 orthopedic surgeons independently estimated the volume of these 5 OLT via standard MRI. Next, 3D reconstructions were created and morphometric true-volume (MTV) analysis measurements of each OLT were generated. The percent change in volumes from CT and MR was compared based upon MTVs determined from 3D reconstructive analysis.

RESULTS

The volume calculated using conventional methods in CT and MR scans grossly overestimated the size by of the OLT by 285-864% and 56-374% respectively when compared to 3D true-volume analysis of those CT and MR scans.

CONCLUSIONS

This study demonstrates that true-volume is more accurate for calculating lesion size than conventional methods. Additionally, when comparing MRI and CT, thin slice CT true-volume is superior to MRI true-volume. True-volume calculation improves accuracy with CT and MRI and should be recommended for use in revision OLT cases.Levels of Evidence: Level III: Case control study.

Three-Dimensional Segmentation and in silico Comparison of Equine Deep Digital Flexor Tendon Pathology in Horses Undergoing Repeated MRI Examination

The use of magnetic resonance imaging (MRI) has led to increased clinical and research applications using 3D segmentation and reconstructed volumetric data in musculoskeletal imaging. Lesions of the deep digital flexor tendon (DDFT) are a common pathology in horses undergoing MRI. Three-dimensional MRI reconstruction performed for volumetric tendon analysis in horses has not previously been documented. The aim of this proof-of-concept study was to evaluate the 3D segmentation of horses undergoing repeated MRI at several time points and to perform an analysis of the segmented DDFTs across time. MRI DICOM files were acquired from six horses undergoing repeated MRI examination of the foot for DDFT injury. Once segmented, volumetric tendon surface tessellation language (STL) files were created. Thickness and volumetric data were acquired for each tendon in addition to a tendon comparison across timepoints within each horse. Pearson correlation coefficients were calculated for comparison of MRI reports to computer analysis. There was a significant and positive correlation between MRI and medial record reports of clinical improvement or deterioration and computer analysis (r = 0.56, p = 0.01). The lower end range limit for tendon thickness varied between 0.16 and 1.74 mm. The upper end range limit for DDFT thickness varied between 4.6 and 23.6 mm. During tendon part comparison, changes in DDFT were reported between −3.0 and + 14.3 mm. Changes in DDFT size were non-uniform and demonstrated fluctuations throughout the tendon. The study was successful in establishing the volumetric appearance and thickness of the DDFT as it courses in the foot and tracking this over time. We encountered difficulties in accurate segmentation of the distal insertion of the DDFT as it blends with the distal phalanx. The data demonstrated that the DDFT can be segmented and volumetric studies based on size and shape can be performed using an in silico approach.

3D MRI: Technical Considerations and Practical Integration

One of the main advantages of three-dimensional (3D) magnetic resonance imaging (MRI) is the possibility of isotropic voxels and reconstructed planar cuts through the volumetric data set in any orientation with multiplanar reformation software through real-time evaluation. For example, reformats by the radiologist during reporting allows exploitation of the full potential of isotropic 3D volumetric acquisition or through standardized retrospective reformats of thicker predefined slices of an isotropic volumetric data set by technologists. The main challenges for integrating 3D fast spin echo (FSE) and turbo spin-echo (TSE) MRI in clinical practice are a long acquisition time and some artifacts, whereas for integrating 3D gradient-recalled echo protocols, the main challenges are lower signal-to-noise ratios (SNRs) and the inability to produce intermediate, and T2-weighted contrast. The implementation of bidirectional parallel imaging acquisition and random undersampling acceleration strategies of 3D TSE pulse sequences substantially shortens the examination time with only minor SNR reductions. This article provides an overview of general technical considerations of 3D FSE and TSE sequences in musculoskeletal MRI. It also describes how these sequences achieve efficient data acquisition and reviews the main advantages and challenges for their introduction to clinical practice.

3D MRI of the Ankle: A Concise State-of-the-Art Review

Magnetic resonance imaging (MRI) is a powerful imaging modality for visualizing a wide range of ankle disorders that affect ligaments, tendons, and articular cartilage. Standard two-dimensional (2D) fast spin-echo (FSE) and turbo spin-echo (TSE) pulse sequences offer high signal-to-noise and contrast-to-noise ratios, but slice thickness limitations create partial volume effects. Modern three-dimensional (3D) FSE/TSE pulse sequences with isotropic voxel dimensions can achieve higher spatial resolution and similar contrast resolutions in ≤ 5 minutes of acquisition time. Advanced acceleration schemes have reduced the blurring effects of 3D FSE/TSE pulse sequences by affording shorter echo train lengths. The ability for thin-slice partitions and multiplanar reformation capabilities eliminate relevant partial volume effects and render modern 3D FSE/TSE pulse sequences excellently suited for MRI visualization of several oblique and curved structures around the ankle. Clinical efficiency gains can be achieved by replacing two or three 2D FSE/TSE sequences within an ankle protocol with a single isotropic 3D FSE/TSE pulse sequence. In this article, we review technical pulse sequence properties for 3D MRI of the ankle, discuss practical considerations for clinical implementation and achieving the highest image quality, compare diagnostic performance metrics of 2D and 3D MRI for major ankle structures, and illustrate a broad spectrum of ankle abnormalities.

3D MRI of the Spine

Three-dimensional (3D) magnetic resonance imaging of the spine is now clinically feasible due to technological advancements. Its advantages over two-dimensional imaging include higher in-plane spatial resolution and the ability for reformation in any plane that enables time savings in image acquisition and aids more accurate interpretation. Multispectral 3D techniques for imaging around metal are sometimes useful for evaluating anatomy adjacent to spinal fixation hardware. 3D gradient-recalled echo sequences, including ultrashort or zero time to echo sequences, can provide osseous detail similar to conventional computed tomography.

3D MRI of the Shoulder

Magnetic resonance imaging provides a comprehensive evaluation of the shoulder including the rotator cuff muscles and tendons, glenoid labrum, long head biceps tendon, and glenohumeral and acromioclavicular joint articulations. Most institutions use two-dimensional sequences acquired in all three imaging planes to accurately evaluate the many important structures of the shoulder. Recently, the addition of three-dimensional (3D) acquisitions with 3D reconstructions has become clinically feasible and helped improve our understanding of several important pathologic conditions, allowing us to provide added value for referring clinicians. This article briefly describes techniques used in 3D imaging of the shoulder and discusses applications of these techniques including measuring glenoid bone loss in anterior glenohumeral instability. We also review the literature on routine 3D imaging for the evaluation of common shoulder abnormalities as 3D imaging will likely become more common as imaging software continues to improve.

Clinical utility of fat-suppressed 3-dimensional controlled aliasing in parallel imaging results in higher acceleration sampling perfection with application optimized contrast using different flip angle evolutions MRI of the knee in adults

OBJECTIVE

To compare htree-dimensional CAIPIRINHA SPACE and two-dimensional turbo spin echo (2D TSE) MRI in the diagnosis of knee pathology in symptomatic adult patients.

METHODS

From February to September in 2018, 120 patients who underwent a knee MRI using both 3D CAIPIRINHA SPACE and 2D TSE MRI were enrolled. The signal-to-noise ratios (SNRs) and contrast-to-noise ratio (CNR) of the 2D and 3D MRI were compared using a paired t-test. Two radiologists independently evaluated both 2D and 3D MRI images using scoring systems for the menisci, ligaments, and cartilage. Intermethod, inter- and intrareader agreements were determined using an intraclass correlation coefficient (ICC). The diagnostic performance of both methods was measured in 44 patients with arthroscopy.

RESULTS

The mean scan time of 3D CAIPIRINHA SPACE MRI (4' 43") was shorter than that of 2D TSE MRI (17' 27"). The mean SNR and CNR of 3D CAIPIRINHA SPACE was higher than those of 2D TSE MRI (mean difference, 3.97 of SNR and 1.58 of CNR; p < 0.001 and p = .038, respectively). Intermethod (ICC, 0.84-1.0) and inter-reader (ICC, 0.75-0.97), and intra-reader agreements (ICC, 0.87-1.0) were good or excellent. The diagnostic accuracy of 3D CAIPIRINHA SPACE sequence was equal for ligament (95.5%) and better for meniscal and cartilage evaluation (84.1% each), compared to 2D TSE MRI (79.5% each).

CONCLUSION

The fat-suppressed 3D CAIPIRINHA SPACE MRI maybe useful in clinical practice for the evaluation of the knee in place of the 2D conventional MRI protocol.

ADVANCES IN KNOWLEDGE

1. The 3D CAIPIRINHA SPACE MRI of the knee joint may be acceptable to be used in clinical practice showing comparable imaging quality compared to conventional 2D TSE MRI.2. Compared with arthroscopic findings as the gold-standard, the diagnostic performance of 3D CAIPIRINHA SPACE MRI was equal or better for knee joint evaluation than that of 2D TSE MRI, as well as with shorter scan time.

MR Neurography: Current Several Issues for Novice Radiologists

말초신경병증의 진단을 위해 MR neurography의 사용이 점차 증가하고 있다. 고대조도와 고해상도로 말초신경을 직접 영상화한 MR 영상을 MR neurography라고 하고, 지방억제 T2 강조영상과 확산강조영상이 흔히 사용되는 시퀀스이다. 작은 직경, 복잡한 해부학적 구조를 가진 말초신경을 합리적 시간 안에 영상화하기 위해서 최신의 isotropic 3차원 기법, 다양한 고속영상기법, post-processing 영상 기법 등이 사용된다. 이런 발전들로 인해 MR neurography가 유용하게 사용되지만 항상 적절한 MR neurography 영상을 얻을 수 있는 것은 아니다. 적절한 MR neurography 영상을 얻기 위해 영상의학과 의사가 고려해야 할 다음의 몇가지 쟁점들이 있다. 이에는 적절한 표준 프로토콜의 선책, 지방억제 기법의 선택, 해상도와 field of view와 slice thickness 간의 상호 관계의 이해, 적절한 post-processing 영상 기법의 적용, 2차원 영상획득 기법과 3차원 영상획득 기법의 장단점, 근위부 말초신경과 말단부 말초신경의 T2 대조도의 차이, 말초신경에 인접한 정맥이 MR neurography에 미치는 영향, 확산강조영상에서 기하학적 왜곡의 발생과 적절한 b value의 선택 등이다. 이런 쟁점들을 잘 이해하는 것이 경험이 적은 영상의학과 의사가 적절한 MR neurography 영상을 얻고, 말초신경병증을 정확히 평가하는 데 많은 도움이 될 것이다.

Magnetic resonance imaging sequence evaluation of an MR Linac system; early clinical experience

OBJECTIVES

To systematically identify the preferred magnetic resonance imaging (MRI) sequences following volunteer imaging on a 1.5 Tesla (T) MR-Linear Accelerator (MR Linac) for future protocol development.

METHODS

Non-patient volunteers were recruited to a Research and Ethics committee approved prospective MR-only imaging study on a 1.5T MR Linac system. Volunteers attended 1-3 imaging sessions that included a combination of mDixon, T1w, T2w sequences using 2-dimensional (2D) and 3-dimensional (3D) acquisitions. Each sequence was acquired over 2-7 minutes and reviewed by a panel of 3 observers to evaluate image quality using a visual grading analysis based on a 4-point Likert scale. Sequences were acquired and modified iteratively until deemed fit for purpose (online image matching or re-planning) and all observers agreed they were suitable in 3 volunteers.

RESULTS

26 volunteers underwent 31 imaging sessions of six general anatomical regions. Images were acquired in one or two of six general anatomical regions: male pelvis (n = 9), female pelvis (n = 4), chestwall/breast (n = 5), lung/oesophagus (n = 5), abdomen (n = 3) and head and neck (n = 5). Images were acquired using a pre-defined exam-card that on average, included six sequences (range 2-10), with a maximum scan time of approximately one hour. The majority of observers preferred T2-weighted sequences. The thorax teams were the only groups to prefer T1-weighted imaging.

CONCLUSIONS

An iterative process identified sequence agreement in all anatomical regions. These sequences will now be evaluated in patient volunteers.

ADVANCES IN KNOWLEDGE

This manuscript is the first publication sharing the results of the first systematic selection of MRI sequences for use in on-board MRI-guided radiotherapy by end-users (therapeutic radiographers and clinical oncologists) in healthy volunteers.

Consensus recommendations on standardized magnetic resonance imaging protocols for multicenter canine brain tumor clinical trials

The National Cancer Institute Comparative Brain Tumor Consortium, Patient Outcomes Working Group, propose a consensus document in support of standardized magnetic resonance imaging protocols for canine brain tumor clinical trials. The intent of this manuscript is to address the widely acknowledged need to ensure canine brain tumor imaging protocols are relevant and have sufficient equivalency to translate to human studies such that: (1) multi-institutional studies can be performed with minimal inter-institutional variation, and (2) imaging protocols are consistent with human consensus recommendations to permit reliable translation of imaging data to human clinical trials. Consensus recommendations include pre- and postcontrast three-dimensional T1-weighted images, T2-weighted turbo spin echo in all three planes, T2*-weighted gradient recalled echo, T2-weighted fluid attenuated inversion recovery, and diffusion weighted imaging/diffusion tensor imaging in transverse plane; field of view of ≤150 mm; slice thickness of ≤2 mm, matrix ≥ 256 for two-dimensional images, and 150 or 256 for three-dimensional images.

Preoperative detection of malignant liver tumors: Comparison of 3D-T2-weighted sequences with T2-weighted turbo spin-echo and single shot T2 at 1.5 T

PURPOSE

To assess the performances of three-dimensional (3D)-T2-weighted sequences compared to standard T2-weighted turbo spin echo (T2-TSE), T2-half-Fourier acquisition single-shot turbo spin-echo (T2-HASTE), diffusion weighted imaging (DWI) and 3D-T1-weighted VIBE sequences in the preoperative detection of malignant liver tumors.

METHODS

From 2012 to 2015, all patients of our institution undergoing magnetic resonance imaging (MRI) examination for suspected malignant liver tumors were prospectively included. Patients had contrast-enhanced 3D-T1-weighted, DWI, 3D-T2-SPACE, T2-HASTE and T2-TSE sequences. Imaging findings were compared with those obtained at follow-up, surgery and histopathological analysis. Sensitivities for the detection of malignant liver tumors were compared for each sequence using McNemar test. A subgroup analysis was conducted for HCCs. Image artifacts were analyzed and compared using Wilcoxon paired signed rank-test.

RESULTS

Thirty-three patients were included: 13 patients had 40 hepatocellular carcinomas (HCC) and 20 had 54 liver metastases. 3D-T2-weighted sequences had a higher sensitivity than T2-weighted TSE sequences for the detection of malignant liver tumors (79.8% versus 68.1%; P < 0.001). The difference did not reach significance for HCC. T1-weighted VIBE and DWI had a higher sensitivity than T2-weighted sequences. 3D-T2-weighted-SPACE sequences showed significantly less artifacts than T2-weitghted TSE.

CONCLUSION

3D-T2-weighted sequences show very promising performances for the detection of liver malignant tumors compared to T2-weighted TSE sequences.

Accuracy of 3 Tesla magnetic resonance imaging using detection of fiber loss and a visual analog scale for diagnosing partial and complete cranial cruciate ligament ruptures in dogs

Canine cranial cruciate ligament rupture is often bilateral and asymmetrical, ranging from partial to complete rupture. The purpose of our diagnostic accuracy study was to assess the accuracy of 3 Tesla magnetic resonance imaging (MRI) detection of fiber loss and use of a visual analog scale in the diagnosis of complete versus partial cranial cruciate ligament rupture in 28 clinical dogs with unilateral complete rupture and contralateral partial rupture. Three Tesla MRI was performed on 56 stifles using sagittal sequences (T2-weighted fast spin echo with fat saturation, proton density fast spin echo, and T2-weighted 3D fast spin echo CUBE). Two MRI observers assessed the cranial cruciate ligament for fiber loss and completed a visual analog scale. The MRI data were compared to arthroscopy and clinical status. Accuracy classifying partial or complete rupture was assessed using receiver operating characteristic analysis. Compared to arthroscopy, for complete cranial cruciate ligament rupture, sensitivity, specificity, and accuracy of MRI detection of fiber loss were 0.78, 0.50-0.60, and 0.68-0.71, respectively, and, for partial tears, specificity was 1.00. An MRI visual analog scale score ≥79 was indicative of complete cranial cruciate ligament rupture (sensitivity 0.72-0.94 and specificity 0.71-0.84). Using a visual analog scale cut-point ≥79, observers achieved good accuracy discriminating clinical status of partial or complete cranial cruciate ligament rupture (area under the curve 0.87-0.93). MRI evaluation for fiber loss and use of a visual analog scale are specific in stifles with clinically stable partial cranial cruciate ligament rupture. In stifles with clinically unstable complete cranial cruciate ligament rupture, both MRI tests are sensitive though not specific compared to arthroscopy. As a diagnostic imaging method, MRI may help guide treatment in patients with cranial cruciate ligament damage, particularly for stable partial rupture.

Automated T2-mapping of the Menisci From Magnetic Resonance Images in Patients with Acute Knee Injury

RATIONALE AND OBJECTIVES

This study aimed to evaluate the accuracy of an automated method for segmentation and T2 mapping of the medial meniscus (MM) and lateral meniscus (LM) in clinical magnetic resonance images from patients with acute knee injury.

MATERIALS AND METHODS

Eighty patients scheduled for surgery of an anterior cruciate ligament or meniscal injury underwent magnetic resonance imaging of the knee (multiplanar two-dimensional [2D] turbo spin echo [TSE] or three-dimensional [3D]-TSE examinations, T2 mapping). Each meniscus was automatically segmented from the 2D-TSE (composite volume) or 3D-TSE images, auto-partitioned into anterior, mid, and posterior regions, and co-registered onto the T2 maps. The Dice similarity index (spatial overlap) was calculated between automated and manual segmentations of 2D-TSE (15 patients), 3D-TSE (16 patients), and corresponding T2 maps (31 patients). Pearson and intraclass correlation coefficients (ICC) were calculated between automated and manual T2 values. T2 values were compared (Wilcoxon rank sum tests) between torn and non-torn menisci for the subset of patients with both manual and automated segmentations to compare statistical outcomes of both methods.

RESULTS

The Dice similarity index values for the 2D-TSE, 3D-TSE, and T2 map volumes, respectively, were 76.4%, 84.3%, and 75.2% for the MM and 76.4%, 85.1%, and 76.1% for the LM. There were strong correlations between automated and manual T2 values (r_MM = 0.95, ICC_MM = 0.94; r_LM = 0.97, ICC_LM = 0.97). For both the manual and the automated methods, T2 values were significantly higher in torn than in non-torn MM for the full meniscus and its subregions (P < .05). Non-torn LM had higher T2 values than non-torn MM (P < .05).

CONCLUSIONS

The present automated method offers a promising alternative to manual T2 mapping analyses of the menisci and a considerable advance for integration into clinical workflows.

New Techniques in MR Imaging of the Ankle and Foot

Foot and ankle disorders are common in everyday clinical practice. MR imaging is frequently required for diagnosis given the variety and complexity of foot and ankle anatomy. Although conventional MR imaging plays a significant role in diagnosis, contemporary management increasingly relies on advanced imaging for monitoring therapeutic response. There is an expanding need for identification of biomarkers for musculoskeletal tissues. Advanced imaging techniques capable of imaging these tissue substrates will be increasingly used in routine clinical practice. Radiologists should therefore become familiar with these innovative MR techniques. Many such techniques are already widely used in other organ systems.

Advanced MRI Techniques for the Ankle

OBJECTIVE

The purposes of this article are to present a state-of-the-art routine protocol for MRI of the ankle, to provide problem-solving tools based on specific clinical indications, and to introduce principles for the implementation of ultrashort echo time MRI of the ankle, including morphologic and quantitative assessment.

CONCLUSION

Ankle injury is common among both athletes and the general population, and MRI is the established noninvasive means of evaluation. The design of an ankle protocol depends on various factors. Higher magnetic field improves signal-to-noise ratio but increases metal artifact. Specialized imaging planes are useful but prolong acquisition times. MR neurography is useful, but metal reduction techniques are needed whenever a metal prosthesis is present. An ultrashort echo time sequence is a valuable tool for both structural and quantitative evaluation.