Determination of Malachite Green in Aquaculture Water by Adsorptive Stripping Voltammetry

Multiphase electroextraction of malachite green from surface water and its determination using digital imaging and chemometric tools

This study introduces a novel method for the quantification of malachite green (MG), a pervasive cationic dye, in surface water by synergizing multiphase electroextraction (MPEE) with digital image analysis (DIA) and partial least square discriminant analysis. Aimed at addressing the limitations of conventional DIA methods in terms of quantitation limits and selectivity, this study achieves a significant breakthrough in the preconcentration of MG using magnesium silicate as a novel sorbent. Demonstrating exceptional processing efficiency, the method allows for the analysis of 10 samples within 20 min, exhibiting remarkable sensitivity and specificity (over 0.95 and 0.90, respectively) across 156 samples in both training and test sets. Notably, the method detects MG at low concentrations (0.2 µg L-1) in complex matrices, highlighting its potential for broader application in environmental monitoring. This approach not only underscores the method's cost-effectiveness and simplicity but also its precision, making it a valuable tool for the preliminary testing of MG in surface waters. This study underscores the synergy among MPEE, DIA, and chemometric tools, presenting a cost-efficient and reliable alternative for the sensitive detection of water contaminants.

Voltammetric Behaviour of Rhodamine B at a Screen-Printed Carbon Electrode and Its Trace Determination in Environmental Water Samples

The voltammetric behaviour of Rhodamine B was studied at a screen-printed carbon electrode (SPCE), by cyclic and differential pulse voltammetry. Cyclic voltammograms exhibited two reduction peaks (designated R1 and R2) generated from the reduction of the parent compound through, first, one electron reduction (R1) to give a radical species, and then a further one-electron, one-proton reduction to give a neutral molecule (R2). On the reverse positive-going scan, two oxidation peaks were observed. The first, O1, resulted from the oxidation of the species generated at R2, and the second, O2, through the one-electron oxidation of the amine group. The nature of the redox reactions was further investigated by observing the effect of scan rate and pH on the voltammetric behaviour. The developed SPCE method was evaluated by carrying out Rhodamine B determinations on a spiked and unspiked environmental water sample. A mean recovery of 94.3% with an associated coefficient of variation of 2.9% was obtained. The performance characteristics indicated that reliable data may be obtained for Rhodamine B measurements in environmental water samples using this approach.

Sunlight-active phytol-ZnO@TiO2 nanocomposite for photocatalytic water remediation and bacterial-fouling control in aquaculture: A comprehensive study on safety-level assessment

With a growing consciousness of the importance of nature stewardship, researchers are focusing their efforts on utilizing renewable energy, particularly solar energy, to address environmental concerns. In this context, photocatalysis has long been viewed as one of the most promising cleaning methods. Hence, we have prepared a sunlight-active phytol-assisted ZnO-TiO₂ nanocomposite (PZTN) for photocatalytic bacterial deactivation and dye degradation process. The PZTN-photocatalysis effectively deactivated the bacterial pathogens as well as malachite green dye within 240 min under direct-sunlight. Moreover, this will be the first complete study on safety level assessment of photocatalytically-remediated water through toxicity studies. The obtained results evidenced that photocatalytically-deactivated bacteria and MG-dye showed to have no toxic effects, signifying that the PZTN-photocatalyzed water seems to be extremely safe for the environment. As a result of this research, we suggest that the PZTN could be a promising sunlight-active photocatalyst for environmental water treatment. On the other hand, biofouling is a ubiquitous phenomenon in the marine environment. Bacteria are the first organisms to foul surfaces and produce biofilms on man-made submerged materials. Interestingly, PZTN-coated PVC plastic-films effectively disallowed biofilms on their surface. This part of this research suggests that PZTN coated PVC-plastics are the best alternative for biofouling management.

Quantification of twenty pharmacologically active dyes in water samples using UPLC-MS/MS

This study presents a multi-compound method for the determination of 20 pharmacologically active dyes from 5 different chemical classes in environmental water samples. These compounds, including triphenylmethane dyes (malachite green, crystal violet, brilliant green, ethyl violet, methyl violet 2B, pararosaniline, victoria blue B, victoria blue R, victoria pure blue BO), phenothiazine dyes (methylene blue, azure A, azure B, azure C, new methylene blue, thionine), phenoxazine dye (nile blue A), acridine dyes (acriflavine, proflavine) and xanthene dyes (rhodamine B, rhodamine 6G) constitute pharmacologically active substances (PASs). For the optimisation of sample preparation, different solid-phase extraction (SPE) sorbents and a wide range of pH (from 2 to 12) of water samples were tested. Finally, water samples were preconcentrated and cleaned up on diol SPE cartridges. Extracts were analysed by ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) operating in the positive electrospray ionisation (ESI+) mode. The chromatographic separation of the 20 pharmacologically active dyes was achieved within 5 min by using a pentafluorophenyl (F5) analytical column and mobile phases of ammonium acetate buffer (0.05 M, pH = 3.5) and acetonitrile with gradient elution. The developed method was validated proving to be suitable for the determination of all tested compounds. Limits of quantification were 0.01–0.1 μg/l, are sensitive enough to quantify very low concentration levels of the dyes in environmental water samples. The obtained recovery values for all tested analytes were between 71.2 and 104.9% with a good RSD, less than 14 % at all fortification levels. The application of the developed method to water samples allows the detection of dyes such as crystal violet, rhodamine B, and methyl violet in two wastewater samples in concentration range from 0.017 to 0.0043 μg/l).

Green antimicrobial adsorbent containing grafted xanthan gum/SiO2 nanocomposites for malachite green dye

Recently, removal of synthetic dyes, especially cationic dye of malachite green (MG), and inhibition of the growth of pathogenic microorganism from drinking water have gained much interest due to their high toxic potency for aquatic biosystems. Herein, a new dye adsorbent with outstanding antibacterial activity was fabricated based on xanthan gum (XG) and SiO₂ nanoparticles through ultrasonication followed by the crosslinking polymerization with vinyl imidazole monomer. The nano adsorbents were characterized with various techniques such as FTIR, XRD, SEM, EDX, and TEM. The nanocomposites were applied as a filter for discarding MG dye and killing the growth of bacterial strains such as E.coli and S.aureus which are considered as the common impurities for drinking water. The data revealed that a maximum adsorption capacity was recorded as 99.5% (Q_max = 588.2 mg/g) at optimum conditions including 10 mg nanocomposite, 10 mL of MG dye (450 ppm), pH = 7, the temperature of 30 °C, and the adsorption time was adjusted within 6 h. The process of dye adsorption was applied to the common isotherm models of Langmuir, Temkin, and Freundlich, and the findings showed that the adsorption behavior was well fitted with the Langmuir one (R² = 0.9983). Moreover, different adsorption kinetic models such as pseudo-first order, pseudo-second order, and intra-particle diffusion were studied for understanding the mechanism of MG adsorption onto nanocomposite surface. It was found that both intraparticle diffusion and pseudo-first-order have participated evenly in the adsorption mechanism of MG dye. Ultimately, the as-prepared nanocomposites were tested against the growth of S. aureus, and E.coli manifesting a superior inhibition diameter as 23.5 ± 0.50, and 25.33 ± 0.47 mm against E.coli, and S. aureus, respectively. Therefore, our new XG-g-PVI/SiO₂ adsorbent is a very promising adsorbent for the fast and efficient capture of dyes from aqueous solutions.

Quantitative Analysis of Malachite Green in Environmental Samples Using Liquid Chromatography-Mass Spectrometry

Water is an essential part of life, however, with continued modernization, it has become a dumping place for many pollutants including dyes. The polluted water can severely affect human health. Polluted water can enter into the human body through different channels, including the food web. Thus, it is very important for human beings and animals to have access to pollution free water. To get the knowledge of the pollutants, in this case, a dye, we need sensitive analytical procedure which could tell the amount of dye in water and also steps to get the pollutant removed from water. In this work, a liquid chromatography–mass spectrometry (LC-MS/MS) based analytical method was developed to determine malachite green. The method was developed after proper optimization of the experimental conditions, where finally, ethanol, a green solvent and formic acid, a food additive was selected to constitute the mobile phase in ratio 1.5:1.0. Different validation parameters were used to authenticate the reliability of the method. Based on the experiment results, the method was found to be linear in the range of 0.1 to 10 mg/L with an excellent correlation coefficient of 0.9995. The corresponding linear regression equation was found to be A = −6863.2 + 105,520 C; where A is the area of the peak and C is the concentration of malachite green. The precision study proves the reproducibility of LC-MS/MS procedure, throughout the precision experiment percent relative standard deviation (% RSD) was found to be between 0.709–1.893%. Similarly, the experiments on the recovery suggest a recovery of 97.28–98.75%. The new method was applied to check the amount of malachite green in environmental samples including the industrial wastewater. The wastewater sample was extracted using the solid phase extraction (SPE) technique, where a new adsorbent—wood apple hydrochar—was synthesized and used as the solid phase for the preparation of a solid phase extraction column to extract the malachite green. The synthesized adsorbent was characterized using different techniques. To conclude, the developed method can be used for determination of malachite green in environmental samples, and the SPE technique using wood apple hydrochar can successfully extract the dye from the water samples.

Large-volume electric field-assisted multiphase extraction of malachite green from water samples: A multisample device and method validation

In this work, a new large-volume multiphase, multi-sample electroextraction device was developed and applied to selectively extract malachite green (MG) from water samples. This device was easily constructed with ordinary materials and capable of extracting ten samples simultaneously, obtaining MG preconcentrated on a solid support, to fit into a pipette tip. A multi-well plate was applied to extract MG from aquaculture water samples, and the extracts containing the desorbed MG were analysed by LC-DAD and LC-MS/MS. The signals from both detectors were used in two independent validation procedures. Linearity, matrix effect, selectivity, precision, trueness, and limits of detection and quantification were all evaluated. For both detectors, linearity was demonstrated in the range of 0.5-5 μg L^-1 (R² > 0.98). Matrix effect was insignificant for LC-DAD only, and the average preconcentration factor was about 60 times. Recoveries ranged from 94 to 113% for LC-DAD and 95-115% for LC-MS/MS analysis. ANOVA was applied to estimate the standard deviation under repeatability (6.96-8.61% for LC-DAD and 5.98-7.41% for LC-MS/MS) and within-reproducibility (6.96-8.61% for LC-DAD and 6.56-7.41% for LC-MS/MS) conditions. The limits of detection and quantification for LC-MS/MS analysis were 4.29 and 28.74 ng L^-1, respectively, while, for LC-DAD, these limits were 14.29 and 95.81 ng L^-1, respectively. The results demonstrated that the developed method was suitable for determining MG in water samples, and the large-volume multiphase, multi-sample electroextraction device proved to be a powerful sample preparation technique to obtain high clean-up and large preconcentration levels, which are of paramount importance for environmental applications.

Cation and anion electrochemically assisted solid-state transformations of malachite green

The possibility of the electrochemical promotion of different solid-to-solid transformations including the performance of successive cation and anion insertion processes has been tested using malachite green, a triphenylmethane dye, in contact with aqueous NaCl electrolyte. Electrochemical data using the voltammetry of microparticles methodology reveal significant differences with the solution phase electrochemistry of the dye. Voltammetric data, combined with atomic force microscopy, focusing ion beam-field emission scanning electron microscopy, and high-resolution field emission scanning electron microscopy permit characterization of the oxidative dissolution, oxidation with anion insertion, reduction with cation insertion and reduction with anion issue processes, whose thermochemical aspects, involving separate ion and electron transport contributions, are discussed.

Resolution of mixed dyes by in situ near infrared (NIR) spectroelectrochemistry

NIR spectroelectrochemistry has scarcely been used for deconvolving aqueous mixtures due to the water restriction in this spectral range. However, this work offers an interesting approach for the study of mixtures of molecules with similar electrochemical and spectroscopic behaviour by overcoming the limitations of this hybrid technique. As a proof of concept, the resolution of mixtures of two dyes with similar chemical structures demonstrates the usefulness of NIR spectroelectrochemistry.

A comprehensive study on the electrocatalytic degradation, electrochemical behavior and degradation mechanism of malachite green using electrodeposited nanostructured β-PbO2 electrodes

This work has investigated the electrocatalytic degradation of malachite green (MG) in aqueous solution with G/β-PbO₂, SS316/β-PbO₂, Ti/β-PbO₂ and Pb/β-PbO₂ electrodes. These electrodes show high oxygen evolution over-potential and excellent electrochemical degradation efficiency for organic pollutants. The optimum conditions for the degradation of MG were obtained by studying the effects of different parameters, such as initial current densities and initial MG concentration. The remaining organic compounds concentrations (color) and chemical oxygen demand (COD) removal efficiency were investigated and compared. The results indicate that the efficiency of G/β-PbO₂ electrode for both color and COD removals is more than those of other electrodes. At the optimum conditions, the color and COD removal efficiencies of MG reached up to 100% and 94%, respectively. The observed degradation rate of MG was found to vary in the order G/β-PbO₂> SS316/β-PbO₂> Ti/β-PbO₂> Pb/β-PbO₂. Moreover, in this paper, the electrochemical behavior and adsorption characteristic of MG in aqueous solutions with different pH values were studied in details at glassy carbon electrode using both constant-current coulometry and cyclic voltammetry techniques. This study has led to the proposed mechanism for the oxidation pathway of MG and determine the absorption properties of MG in acidic, neutral and basic solutions. We also proposed the mineralization pathway of MG at β-PbO₂ electrode.

Ag-Coated Cellulose Fibers as Surface-Enhanced Raman Scattering Substrates for Adsorptive Detection of Malachite Green

Surface-enhanced Raman scattering (SERS) is a sensitive technique for the detection of low concentration analytes. In this study, we used cellulose fibers (CF) as the templates for the loading of silver nanoparticles (Ag NPs), and the obtained CF-Ag was applied in the detection of R6G and Malachite Green (MG) by surface-enhanced Raman scattering. The adsorption technique was employed in the sample preparation, and the optimal detecting status was identified in the dynamic range (sample status ranging from wet to dry) for different concentration of analytes. In comparison to Ag NPs, CF-Ag showed enhanced performance for adsorptive detection of Malachite Green, and the limit of detection was 5 × 10^-12 M.