Adsorptive removal of congo red dye (CR) from aqueous solution by Cornulaca monacantha stem and biomass-based activated carbon: isotherm, kinetics and thermodynamics

Sorption Behavior of Azo Dye Congo Red onto Activated Biochar from Haematoxylum campechianum Waste: Gradient Boosting Machine Learning-Assisted Bayesian Optimization for Improved Adsorption Process

This work aimed to describe the adsorption behavior of Congo red (CR) onto activated biochar material prepared from Haematoxylum campechianum waste (ABHC). The carbon precursor was soaked with phosphoric acid, followed by pyrolysis to convert the precursor into activated biochar. The surface morphology of the adsorbent (before and after dye adsorption) was characterized by scanning electron microscopy (SEM/EDS), BET method, X-ray powder diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) and, lastly, pHpzc was also determined. Batch studies were carried out in the following intervals of pH = 4-10, temperature = 300.15-330.15 K, the dose of adsorbent = 1-10 g/L, and isotherms evaluated the adsorption process to determine the maximum adsorption capacity (Qmax, mg/g). Kinetic studies were performed starting from two different initial concentrations (25 and 50 mg/L) and at a maximum contact time of 48 h. The reusability potential of activated biochar was evaluated by adsorption-desorption cycles. The maximum adsorption capacity obtained with the Langmuir adsorption isotherm model was 114.8 mg/g at 300.15 K, pH = 5.4, and a dose of activated biochar of 1.0 g/L. This study also highlights the application of advanced machine learning techniques to optimize a chemical removal process. Leveraging a comprehensive dataset, a Gradient Boosting regression model was developed and fine-tuned using Bayesian optimization within a Python programming environment. The optimization algorithm efficiently navigated the input space to maximize the removal percentage, resulting in a predicted efficiency of approximately 90.47% under optimal conditions. These findings offer promising insights for enhancing efficiency in similar removal processes, showcasing the potential of machine learning in process optimization and environmental remediation.

Upcycling of sugar refining mud solid waste as a novel adsorbent for removing methylene blue and Congo red from wastewater

The feasibility of utilizing the mud solid waste (MSW) produced during the carbonation process of sugar refining as a cost-effective and environmentally friendly alternative for the water removal of methylene blue (MB) and Congo red (CR), being highly utilized organic dyes representing cationic and anionic species, respectively is presented. Prior to its use, the MSW was dried at 110 °C for 24 h and sieved through a 100-mesh screen. The chief constituent of the MSW utilized was CaCO3, with a point of zero charge (PZC) found at pH 8.4 and 7.96 m2 g-1 total surface area. XRD and FTIR data indicate the presence of interactions between the dyes and the MSW surface, indicating effective adsorption. Different variables, such as initial dye concentration, MSW weight, solution pH, contact time, and temperature, were all examined to determine the optimal dye removal conditions. A central composite design (CCD) approach based on response surface methodology (RSM) modeling was utilized to identify statistically significant parameters for MB and CR adsorption capacities onto the MSW adsorbent. The removal equilibrium was typically reached in 120 minutes, with the greatest removal efficiency of CR taking place at pH 2 and 328 K, while the highest MB removal efficiency was obtained at pH 12 and 296 K. Kinetic studies suggest the adsorption of both dyes on the MSW follow pseudo-second-order rates, as evident through the high correlations obtained. Linearized and non-linearized Langmuir models showed strong correlations indicating maximum adsorption capacities of 86.6 and 72.3 mg g-1 for MB and CR, respectively. High regeneration and reusability potential of the MSW was demonstrated especially for the adsorption of CR, where the removal efficiency was nearly constant throughout five adsorption cycles, ranging from 93 to 91%, while the reduction in the removal for MB was much more significantly impacted, diminishing from 95 to 79% after the five cycles.

Glutaraldehyde and terephthaldehyde-crosslinked chitosan for cationic and anionic dyes removal from aqueous solutions: Experimental, DFT, kinetic and thermodynamic studies

Novel chitosan polymers were synthesized using two cross-linkers, Glutaraldehyde and Terephthaldehyde, to enhance stability and efficiency. Characterization techniques (XRD, FTIR, FE-SEM, TGA, DTG, BJH, and BET) confirmed successful synthesis. These polymers were employed as adsorbents for removing Malachite Green (MG) and Congo Red (CR) dyes from water. Batch experiments and DFT calculations investigated the adsorption process, thermodynamics, and kinetics. Results showed the CSGT-III polymer achieved the highest removal efficiency. For initial dye concentrations ([CR]o = 50 mg/L, [MG]o = 20 mg/L) and adsorbent doses (0.8 g/L for CR, 0.4 g/L for MG), removal efficiencies were 96.99 % for CR and 99.07 % for MG. Thermodynamic analysis confirmed the spontaneous nature of adsorption, and the process was endothermic for both dyes. The Langmuir model fitted adsorption isotherms well, indicating a homogeneous surface. Kinetic analysis revealed a pseudo-second-order model for both dyes.

Process Optimization and Equilibrium, Thermodynamic, and Kinetic Modeling of Toxic Congo Red Dye Adsorption from Aqueous Solutions Using a Copper Ferrite Nanocomposite Adsorbent

In the present investigation of copper ferrite, a CuFe2O4 nanocomposite adsorbent was synthesized using the sol-gel method, and its relevance in the adsorptive elimination of the toxic Congo red (CR) aqueous phase was examined. A variety of structural methods were used to analyze the CuFe2O4 nanocomposite; the as-synthesized nanocomposite had agglomerated clusters with a porous, irregular, rough surface that could be seen using FE-SEM, and it also contained carbon (23.47%), oxygen (44.31%), copper (10.21%), and iron (22.01%) in its elemental composition by weight. Experiments were designed to achieve the most optimized system through the utilization of a central composite design (CCD). The highest uptake of CR dye at equilibrium occurred when the initial pH value was 5.5, the adsorbate concentration was 125 mg/L, and the adsorbent dosage was 3.5 g/L. Kinetic studies were conducted, and they showed that the adsorption process followed a pseudo-second-order (PSO) model (regression coefficient, R2 = 0.9998), suggesting a chemisorption mechanism, and the overall reaction rate was governed by both the film and pore diffusion of adsorbate molecules. The process through which dye molecules were taken up onto the particle surface revealed interactions involving electrostatic forces, hydrogen bonding, and pore filling. According to isotherm studies, the equilibrium data exhibited strong agreement with the Langmuir model (R2 = 0.9989), demonstrating a maximum monolayer adsorption capacity (qmax) of 64.72 mg/g at pH 6 and 302 K. Considering the obtained negative ΔG and positive ΔHads and ΔSads values across all tested temperatures in the thermodynamic investigations, it was confirmed that the adsorption process was characterized as endothermic, spontaneous, and feasible, with an increased level of randomness. The CuFe2O4 adsorbent developed in this study is anticipated to find extensive application in effluent treatment, owing to its excellent reusability and remarkable capability to effectively remove CR in comparison to other adsorbents.

Enhanced photocatalytic performance of milkvetch-derived biochar via ZnO-Ce nanoparticle decoration for reactive blue 19 dye removal

In this research, the photocatalytic removal of reactive blue 19 (RB19) dye is investigated employing zinc oxide/cerium (ZnO@Ce) nanoparticles decorated with biochar under LED irradiation. Synthesis of ZnO@Ce nanoparticles decorated with biochar was performed utilizing the co-precipitation procedure and, then, the texture and morphology of the fabricated nanocomposite were analyzed using energy dispersive X-ray (EDX), field emission scanning electron microscopy (FE-SEM), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), and Fourier transform infrared (FTIR) spectroscopy techniques. Moreover, FE-SEM images demonstrate that ZnO-Ce nanoparticles were successfully decorated on the surface of biochar. The specific surface areas of biochar and biochar/ZnO-Ce were 519.75 and 636.52 m2/g, respectively. To achieve the maximum yield in the removal of RB19 dye, the effects of operating variables including dye concentration, LED lamp power, biochar@ZnO-Ce catalyst dose, pH and H2O2 dose were explored. Besides, the maximum percentage of RB19 dye removal was 96.47% under optimal conditions, i.e. catalyst dosage of 100 mg, H2O2 dosage of 1 mL, pH of 9, initial dye concentration of 5 ppm, LED power of 50 W, and reaction time of 140 min. Furthermore, the kinetic analysis reveals that the removal of RB19 dye follows the pseudo-first order kinetic model, with calculated values of a reaction rate constant of 0.045 min-1 and a correlation coefficient of R2 = 0.99, respectively. Moreover, the reusability and recyclability of biochar@ZnO/Ce nanocatalyst was promising over five runs, with only a 6.08% decrease in RB19 dye removal efficiency. Therefore, it can be concluded that the biochar @ZnO/Ce photocatalyst can be promisingly applied for the removal of azo dyes in aqueous solutions.

The efficient removal of congo red and ciprofloxacin by peony seeds shell activated carbon with ultra-high specific surface area

Preparation of high-performance activated carbon from agroforestry waste biomass can effectively improve the shortcomings of traditional biomass carbon performance. Using the waste biomass peony seeds shell (PSS) as the precursors in this study, high performance activated carbon was prepared by the KOH two-step activation method and used to remove congo red (CR) and ciprofloxacin (CIP) in water pollution. The obtained PSS-based activated carbons (PSACs) were characterized by SEM, EDS, N₂ adsorption-desorption isotherm, FTIR, and XRD methods. The results showed that the activated carbon at 700 °C (PSAC-700) had an ultra-high specific surface area (2980.96 m²/g), excellent micropore volume (1.12 cm³/g), and abundant surface functional groups. The results of adsorption performance revealed that PSAC-700 exhibited excellent adsorption capacity for CR (q_max = 2003.2 mg/g) and CIP (q_max = 782.3 mg/g), which was superior to the carbon-based adsorbents reported reviously in the literature. Langmuir model could well describe the adsorption process of PSACs for CR and CIP, indicating that the pollutant molecules were uniformly adsorbed on the surface monolayer. The regeneration experiment suggested that after three cycles, the adsorption capacities of PSAC-700 for CR and CIP reached 1814 mg/g and 697 mg/g, respectively, with good repeatability. The preparation of PSAC-700 in this study has high adsorption capacity and strong application, which is an ideal material for wastewater purification adsorbent and has broad application prospect.

3D Hierarchical Porous and N-Doped Carbonized Microspheres Derived from Chitin for Remarkable Adsorption of Congo Red in Aqueous Solution

A novel adsorbent of N-doped carbonized microspheres were developed from chitin (N-doped CM-chitin) for adsorption of Congo red (CR). The N-doped CM-chitin showed spherical shape and consisted of carbon nanofibers with 3D hierarchical architecture. There were many micro/nano-pores existing in N-doped CM-chitin with high surface area (455.703 m² g^-1). The N element was uniformly distributed on the carbon nanofibers and formed with oxidize-N graphitic-N, pyrrolic-N, and pyridinic-N. The N-doped CM-chitin showed excellent adsorption capability for CR and the maximum adsorption amount was approximate 954.47 mg g^-1. The π-π/n-π interaction, hydrogen-bond interactions, and pore filling adsorption might be the adsorption mechanisms. The adsorption of N-doped CM-chitin was considered as a spontaneous endothermic adsorption process, and which well conformed to the pseudo-second-order kinetic and Langmuir isotherm model. The N-doped CM-chitin exhibited an effective adsorption performance for dynamic CR water with good reusability. Therefore, this work provides new insights into the fabrication of a novel N-doped adsorbent from low-cost and waste biomasses.

Biofilm-mediated decolorization, degradation and detoxification of synthetic effluent by novel biofilm-producing bacteria isolated from textile dyeing effluent

Biofilm-mediated bioremediation of xenobiotic pollutants is an environmental friendly biological technique. In this study, 36 out of 55 bacterial isolates developed biofilms in glass test tubes containing salt-optimized broth plus 2% glycerol (SOBG). Scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and Congo red- and Calcofluor binding results showed biofilm matrices contain proteins, curli, nanocellulose-rich polysaccharides, nucleic acids, lipids, and peptidoglycans. Several functional groups including -OH, N-H, C-H, CO, COO^-, -NH_2, PO, C-O, and C-C were also predicted. By sequencing, ten novel biofilm-producing bacteria (BPB) were identified, including Exiguobacterium indicum ES31G, Kurthia gibsonii ES43G, Kluyvera cryocrescens ES45G, Cedecea lapagei ES48G, Enterobacter wuhouensis ES49G, Aeromonas caviae ES50G, Lysinibacillus sphaericus ES51G, Acinetobacter haemolyticus ES52G, Enterobacter soli ES53G, and Comamonas aquatica ES54G. The Direct Red (DR) 28 (a carcinogenic and mutagenic dye used in dyeing and biomedical processes) decolorization process was optimized in selected bacterial isolates. Under optimum conditions (SOBG medium, 75 mg L^-1 dye, pH 7, 28 °C, microaerophilic condition and within 72 h of incubation), five of the bacteria tested could decolorize 97.8% ± 0.56-99.7% ± 0.45 of DR 28 dye. Azoreductase and laccase enzymes responsible for biodegradation were produced under the optimum condition. UV-Vis spectral analysis revealed that the azo (-NN-) bond peak at 476 nm had almost disappeared in all of the decolorized samples. FTIR data revealed that the foremost characteristic peaks had either partly or entirely vanished or were malformed or stretched. The chemical oxygen demand decreased by 83.3-91.3% in the decolorized samples, while plant probiotic bacterial growth was indistinguishable in the biodegraded metabolites and the original dye. Furthermore, seed germination (%) was higher in the biodegraded metabolites than the parent dye. Thus, examined BPB could provide potential solutions for the bioremediation of industrial dyes in wastewater.

A sustainable remediation of Congo red dye using magnetic carbon nanodots and B. pseudomycoides MH229766 composite: mechanistic insight and column modelling studies

In the present investigation, a biocomposite, magnetic carbon nanodot immobilized Bacillus pseudomycoides MH229766 (MCdsIB) was developed and consequently characterized using SEM-EDX, FTIR, XRD, and VSM analyses to effectively biotreat hazardous Congo red (CR) dye present in water bodies. The adsorptive efficiency of MCdsIB for the detoxification of CR from wastewater was investigated both in batch and column schemes. Optimum batch parameters were found as pH 3, 50 mg L^-1 dye concentration, 150 min equilibrium time, and 2 g L^-1 MCdsIB dosage. The Freundlich isotherm model best fit the experimental data, and the maximum adsorption capacity of MCdsIB was observed as 149.25 mg g^-1. Kinetic data were in accordance with the pseudo-second-order model where the adsorption rate reduced with the rise in the initial concentration of dye. Intra-particle diffusion was discovered as the rate-limiting step following 120 min of the adsorption process. Furthermore, despite being used continually for five consecutive cycles, MCdsIB demonstrated excellent adsorption capacity (> 85 mg g^-1), making it an outstanding recyclable material. The CR dye was efficiently removed in fixed-bed continuous column studies at high influent CR dye concentration, low flow rate, and high adsorbent bed height, wherein the Thomas model exhibited an excellent fit with the findings acquired in column experiments. To summarize, the current study revealed the effectiveness of MCdsIB as a propitious adsorbent for CR dye ouster from wastewater.

A review on activated carbon modifications for the treatment of wastewater containing anionic dyes

Polluted water resources, particularly those polluted with industrial effluents' dyes, are carcinogenic and hence pose a severe threat to sustainable and longstanding worldwide development. Meanwhile, adsorption is a promising process for polluted/wastewater treatment. In particular, activated carbon (AC) is popular among various wastewater treatment adsorbents, especially in the organic contaminants' remediation in wastewater. Hence, the AC's synthesis from degradable and non-degradable resources, the carbon activation involved in the AC synthesis, and the AC's modification to cutting-edge and effective materials have been modern-research targets in recent years. Likewise, the main research focuses worldwide have been the salient AC characteristics, such as its surface chemistry, porosity, and enhanced surface area. Notably, various modified-AC synthesis methods have been employed to enhance the AC's potential for improved contaminants-removal. Hence, we critically analyze the different modified ACs (with enhanced (surface) functional groups and textural properties) of their capacity to remove different-natured anionic dyes in wastewater. We also discuss the corresponding AC modification techniques, the factors affecting the AC properties, and the modifying agents' influence on the AC's morphological/adsorptive properties. Finally, the AC research of future interest has been proposed by identifying the current AC research gaps, especially related to the AC's application in wastewater treatment.

Biowaste-Derived, Highly Efficient, Reusable Carbon Nanospheres for Speedy Removal of Organic Dyes from Aqueous Solutions

The current work explores the adsorptive efficiency of carbon nanospheres (CNSs) derived from oil palm leaves (OPL) that are a source of biowaste. CNSs were synthesized at 400, 600, 800 and 1000 °C, and those obtained at 1000 °C demonstrated maximum removal efficiency of ~91% for malachite green (MG). Physicochemical and microscopic characteristics were analysed by FESEM, TEM, FTIR, Raman, TGA and XPS studies. The presence of surface oxygen sites and the porosity of CNSs synergistically influenced the speed of removal of MG, brilliant green (BG) and Congo red (CR) dyes. With a minimal adsorbent dosage (1 mg) and minimum contact time (10 min), and under different pH conditions, adsorption was efficient and cost-effective (nearly 99, 91 and 88% for BG, MG and CR, respectively). The maximum adsorption capacities of OPL-based CNSs for BG were 500 and 104.16 mg/g for MG and 25.77 mg/g for CR. Adsorption isotherms (Freundlich, Langmuir and Temkin) and kinetics models (pseudo-first-order, pseudo-second-order and Elovich) for the adsorption processes of all three dyes on the CNSs were explored in detail. BG and CR adsorption the Freundlich isotherm best, while MG showed a best fit to the Temkin model. Adsorption kinetics of all three dyes followed a pseudo-second-order model. A reusability study was conducted to evaluate the effectiveness of CNSs in removing the MG dye and showed ~92% efficiency even after several cycles. Highly efficient CNSs with surface oxygen groups and speedy removal of organic dyes within 10 min by CNSs are highlighted in this paper.

Enhanced adsorption of Congo red dye onto polyethyleneimine-impregnated biochar derived from pine needles

Biochar derived from waste pine needles was chemically modified using polyethyleneimine (PEI) to increase its adsorptive potential for withdrawal of anionic dye Congo red from aqueous solution. PEI impregnation on biochar was confirmed from scanning electron microscopy and energy-dispersive X-ray analysis, Fourier transform infrared spectroscopy, and X-ray diffraction analysis. The surface area of biochar decreased after PEI treatment, but the amine groups increased on biochar surface. PEI-treated biochar displayed considerable increase in adsorption at acidic conditions. Adsorption isotherm was best explained by Langmuir model (R² > 99) and the adsorption kinetics agrees well with pseudo-second-order model. The maximum adsorption capacity of PEI-treated biochar was observed to be 294.11 mg g^-1 and 30.76 mg g^-1 for pristine biochar displaying a 9.5-fold increase. The positive value of standard enthalpy of adsorption (∆H° = 14.96 KJmole^-1) indicated the endothermic nature of adsorption, and positive value of entropy (∆S° = 74.43 Jmole^-1 K^-1) revealed the affinity of biochar towards dye molecules. Negative value of Gibb's free energy ∆G° (- 7.2 KJmole^-1) revealed that the process was spontaneous. Electrostatic interaction appeared to be the key mechanism governing the adsorption process. Thus, PEI-impregnated biochar represents novel low-cost sorbent that can effectively remove anionic dyes which are poorly removed by pristine biochar.

Biologically Synthesized Copper Nanoparticles Show Considerable Degradation of Reactive Red 81 Dye: An Eco-Friendly Sustainable Approach

Diospyros kaki leaf extract was used in this study as a favorable basis for the synthesis of copper nanoparticles (Cu NPs). X-ray diffraction (XRD) and UV-visible spectroscopy approaches were used to characterize the biologically synthesized copper nanoparticles. The XRD analysis showed that copper nanoparticles were face-centered cubic structure. Various experimental levels like conc. of dye, concentration of Cu NPs, pH, reaction time, and temperature were optimized to decolorize reactive red 81 dye using the synthesized Cu NPs. Reactive red 81 dye was decolorized maximum using Cu NPs of 0.005 mg/L. Additionally, reactive red 81 dye was decolorized at its maximum at pH = 6, temperature = 50°C. Our study reported that chemical oxidation demand (COD) and total organic carbon (TOC) deduction efficacies were 74.56% and 73.24%. Further degradation study of reactive red 81 dye was also carried out. Cu NPs have the ability and promising potential to decolorize and degrade reactive red 81 dye found in wastewater.

Kinetics and Adsorption Equilibrium in the Removal of Azo-Anionic Dyes by Modified Cellulose

This study introduces a new and bio-friendly adsorbent based on natural and cetyltrimethylammonium chloride (CTAC)-modified adsorbent prepared from wheat straw residues for the removal of Congo red (CR) and tartrazine azo-anionic dyes from aqueous solution. The adsorbent was characterized by thermogravimetric analysis (TGA), calorimetric differential (DSC), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM/EDX), and pH point of zero charge (pHPZC) techniques. It was found that decreasing the adsorbent dose and increasing the initial concentration favors the removal of tartrazine and Congo red. Tartrazine adsorption capacities were 2.31 mg/g for the cellulose extracted from wheat residues (WC) and 18.85 mg/g for the modified wheat residue cellulose (MWC) for tartrazine as well as 18.5 mg/g for WC and 19.92 for MWC during Congo red (CR) adsorption, respectively. Increasing the initial and decreasing the adsorbent dose concentration favored the adsorption process. From time effect analysis, it was found that the equilibrium time was reached at 120 min when modified wheat cellulose was used and at 480 min when wheat cellulose was used. The kinetics of adsorption were described by pseudo-second-order in all cases with R2 > 0.95. The obtained data equilibrium from this research was well-fitted by the Freundlich isotherm model.

Valorization of food waste as adsorbents for toxic dye removal from contaminated waters: A review

Industrial contaminants such as dyes and intermediates are released into water bodies, making the water unfit for human use. At the same time large amounts of food wastes accumulate near the work places, residential complexes etc. polluting the air due to putrefaction. The need of the hour lies in finding innovative solutions for dye removal from wastewater streams. In this context, the article emphasizes adoption or conversion of food waste materials, an ecological nuisance, as adsorbents for the removal of dyes from wastewaters. Adsorption, being a well-established technique, the review critically examines the specific potential of food waste constituents as dye adsorbents. The efficacy of food waste-based adsorbents is examined, besides addressing the possible adsorption mechanisms and the factors affecting phenomenon such as pH, temperature, contact time, adsorbent dosage, particle size, and ionic strength. Integration of information and communication technology approaches with adsorption isotherms and kinetic models are emphasized to bring out their role in improving overall modeling performance. Additionally, the reusability of adsorbents has been highlighted for effective substrate utilization. The review makes an attempt to stress the valorization of food waste materials to remove dyes from contaminated waters thereby ensuring long-term sustainability.

Evaluation of Three Biomaterials from Coconut Mesocarp for Use in Water Treatments Polluted with an Anionic Dye

Coconut consumption leads to the generation of a large number of fibrous residues such as epicarp and mesocarp. In this study, bioadsorbents were prepared from coconut shells (CS), coconut cellulose (CC) and treated coconut cellulose (MCC) with cetyl trimethyl ammonium chloride (CTAC) for the elimination of Congo red (CR) in a watery solution. The impact of the adsorbent quantity (15, 25 and 35 mg) and initial concentration (40, 70 and 100 mg/L) were evaluated. Fourier transform infrared spectra (FTIR) confirmed the existence of OH−, C=O, COOH and CH2 groups in the adsorbents as well as the deformation of the bands between 3400 and 3800 cm−1 after the adsorption of CR, which was attributed to its capture in the bioadsorbent. From the bromatological analysis, a content of 48.94% lignin, 35.99% cellulose and 10.51% hemicellulose was found. SEM images showed a lignocellulosic essential surface origin for all adsorbents with presence of folds, roughness of an irregular exposed area and fibrous filaments. The average particle size was 0.45 mm and adsorbents had a mean porosity of 0.58. Increasing the initial concentration had a beneficial influence on the removal efficiency of CR, achieving a 99.9% removal with MCC. CS showed slow kinetics in the initial stages whereas CC and MCC achieved 78% and 99.98% removal at 120 min, respectively; an equilibrium was reached at 480 and 20 min, respectively. MCC, CC and CS achieved a maximum qe of 256.12 mg/g, 121.62 mg/g and 17.76 mg/g, respectively.

Bio-synthesized Cu-ZnO hetro-nanostructure for catalytic degradation of organophosphate chlorpyrifos under solar illumination

In present study, a simple, effective and rapid green method using leaf extract of Melia azedarach was explored for the synthesis of Cu-ZnO nano heterojunction particles. The leaf extract of Melia azedarach acts as a reducing agent and prevents the agglomeration of nanoparticles. Different standard analytical techniques were used to study the morphology and size of synthesized nanocomposite. The efficiency of the synthesized material was tested as a photocatalyst for the degradation of simulated wastewater having chlorpyriphos pesticide. The different factors have been investigated such as pH of the solution, catalyst dosage and conact time. Approximately, 81% of chlorpyrifos was degraded after 240 min of solar illumination. The generation of hydroxyl radicals at the catalysts surface owing to photo-irradiation contributed to the chlorpyrifos degradation. The maximum photo-degradation (91%) of pesticides was observed at 6.0 pH. The pathway for the degradation of chlorpyriphos has been checked by LC-MS and this hinting the absence of any harmfull side product. The COD removal and TOC was found to be 32.4% and 28.5%, respectively. The photodegradation of chlorpyriphos using Cu-ZnO nanocomposite was followed the pseudo-first-order kinetic with higher value of regressiuon coefficient (0.99).

Coconut-Water-Mediated Carbonaceous Electrode: A Promising Eco-Friendly Material for Bifunctional Water Splitting Application

The organic and eco-friendly materials are extended to prevail over the worldwide energy crisis where bio-inspired carbonaceous electrode materials are being prepared from biogenic items and wastes. Here, coconut water is sprayed over three-dimensional (3D) nickel foam for obtaining a carbonaceous electrode material, i.e., C@Ni-F. The as-prepared C@Ni-F electrode has been used for structural elucidation and morphology evolution studies. Field emission scanning electron microscopy analysis confirms the vertically grown nanosheets of the C@Ni-F electrode, which is further employed in the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), where excellent OER and HER performances with small overpotentials of 219 and 122 mV and with stumpy Tafel slopes, i.e., 27 and 53 mV dec-1, are respectively obtained, suggesting a bifunctional potential of the sprayed electrode material. Moreover, sustainable bifunctional performance of C@Ni-F proves considerable chemical stability and moderate mechanical robustness against long-term operation, suggesting that, in addition to being a healthy drink to mankind, coconut water can also be used for water splitting applications.

Adsorption of Azo-Anionic Dyes in a Solution Using Modified Coconut (Cocos nucifera) Mesocarp: Kinetic and Equilibrium Study

The effect of adsorbent dose and initial concentration on removing the azo-anionic dyes Congo Red andtartrazine present in a synthetic aqueous solution was studied using natural cellulose (CC) and modified cationic cellulose (MCC) from coconut mesocarp. Three levels of adsorbent dosage (5, 8 and 12 mg/L) and initial concentration (40, 70 and 100 mg/L) were used. Cetyl trimethyl ammonium chloride (CTAC) was used as a modifying agent. TGA and DSC showed that the extracted cellulose was of good quality, composed mostly of cellulose with lignin and hemicellulose traces, and 8% moisture. The FTIR spectrum showed the effectiveness of the modification in the structure of the material with symmetric deformation of the C6H6-Cl group in 1472 cm−1 present in the CTAC. It was found that decreasing the adsorbent dosage and increasing the initial concentration favored the dyes’ adsorption capacity on the two bioadsorbents. Tartrazine removals of 5.67 mg/g on CC and 19.61 mg/g on MCC were achieved, and for CR of 15.52 mg/g on CC and 19.99 with MCC with removal percentages over 97% with the quaternized biomass in all cases. The kinetic and equilibrium study was carried out to identify the mechanisms involved in the adsorption process. The Freundlich model can describe the equilibrium isotherm data of tartrazine on CC and MCC. In contrast, those of CR is defined by the Langmuir and Dubinin–Radushkevic models for CC and MCC, respectively Adsorption kinetics showed that equilibrium was reached at 30 min, with rapid adsorption in the initial minutes with the removal of about 97% of the contaminant in the first 5 min; fitting to kinetic models showed that the kinetics of tartrazine on CC was fitted by Elovich (R2 = 0.756), and on MCC the Elovich (R2 = 0.887) and pseudo-second-order (R2 = 0.999) models. Removing CR on CC was fitted by pseudo-first-order, pseudo-second-order and Elovich models (R2 > 0.98), and when using MCC, all models show a good fitting with R2 = 0.99 in all cases.

Application of Cordia trichotoma sawdust as an effective biosorbent for removal of crystal violet from aqueous solution in batch system and fixed-bed column

In this work, for the first time, Cordia trichotoma sawdust, a residue derived from noble wood processing, was applied as an alternative biosorbent for the removal of crystal violet by discontinuous and continuous biosorption processes. The optimum conditions for biosorption of crystal violet were 7.5 pH and a biosorbent dosage of 0.8 g L^-1. The biosorption kinetics showed that the equilibrium was reached at 120 min, achieving a maximum biosorption capacity of 107 mg g^-1 for initial dye concentration of 200 mg L^-1. The Elovich model was the proper model for representing the biosorption kinetics. The isotherm assays showed that the rise of temperature causes an increase in the biosorption capacity of the crystal violet, with a maximum biosorption capacity of 129.77 mg g^-1 at 328 K. The Langmuir model was the most proper model for describing the behavior. The sign of ΔG⁰ indicates that the process was spontaneous and favorable, whereas the ΔH⁰ indicates an endothermic process. The treatment of the colored simulated effluent composed by dyes and salts resulted in 80% of color removal. The application of biosorbent in the fixed-bed system achieved a breakthrough time of 505 min, resulting in 83.35% of color removal. The Thomas and Yoon-Nelson models were able to describe the fixed-bed biosorption behavior. This collection of experimental evidence shows that the Cordia trichotoma sawdust can be applied for the removal of crystal violet and a mixture of other dyes that contain them.

Removal of Fluorescein Dye from Aqueous Solutions Using Natural and Chemically Treated Pine Sawdust

The various factors affecting the removal of fluorescein dye using sawdust from aqueous solutions such as time, initial concentration, pH, and temperature were studied. The optimal conditions for removing the FD are 1 g of sawdust at pH 3 and 120 min time of contact. Dye removal dropped from 93.42% to 80.04% with natural pine sawdust (NPS) and from 96.83% to 81.51% with synthetic pine sawdust (SPS) by increasing their concentration from 2 to 10 mg/L. Isotherm, kinetic, and thermodynamic models were applied for determining their constants. The results indicated that the FD removal equilibrium was effectively defined by the Langmuir, Freundlich, and Temkin models. Kinetic studies showed that the pseudo-second order was well suited for dye removal, and the internal diffusion process was by two steps. The thermodynamic parameter values suggested that FD removal were physical adsorption, exothermic, lower randomness, and spontaneous.

Adsorption of an anionic dye (Congo red) from aqueous solutions by pine bark

Pinus pinaster bark, an abundant by-product from the timber industry, has been studied as a potential low-cost adsorbent for the removal of Congo red (CR) dye from wastewaters. Surface morphological and physico-chemical characteristics of pine bark were analysed using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), determination of the point of zero charge (pH_PZC) and elemental analysis. Assays were performed to determine the wavelength for the maximum absorbance and the stability with time of CR solutions depending on concentration and/or pH, which resulted to be a very significant parameter. Adsorption studies were conducted on batch mode to study the effect of contact time (till 7 days), pH (2–9), adsorbent dosage (1–10 g L⁻¹) and temperature (25–60 °C). The bark adsorption capacity at equilibrium varied between 0.3 and 1.6 mg g⁻¹ and the equilibrium adsorption percentage between 23.4 and 100% depending on adsorbent dosage, temperature and pH at an initial CR concentration of 5 mg L⁻¹. Kinetic data for the removal of CR by pine bark were best fitted by the pseudo-second-order kinetic model. The equilibrium data fitted well with the Freundlich model. Thermodynamic analysis indicated that the adsorption process is exothermic and spontaneous.