Comments on the Theory of Complex XPS Spectra: Extracting Chemical Information from the Fe 3p XPS of Fe Oxides

Electroplating sludge derived CuFe2O4/MgFe2O4 metal oxide composites for highly efficient removal of Congo red

The utilization of electroplating sludge (ES) to derive metal oxide functional materials is a key strategy, as it enables the recycling of valuable elements, mitigates environmental risks, and aligns with green, low-carbon development strategies. Nevertheless, the development of metal oxide composite functional materials with distinctive structures and properties derived from ES continues to present several challenges. Herein, we synthesized CuFe2O4/MgFe2O4 metal oxide composites from ES by one-step hydrothermal method. As-obtained CuFe2O4/MgFe2O4 metal oxide composites (MMOs) have a unique layered structure, richer mesoporous and microporous structures, activity sites. When evaluated as an adsorbent for Congo red (CR), as-synthesized CuFe2O4/MgFe2O4 with layered structure composite exhibited excellent adsorption capacity (1039.1 mg/g) and reusability (85.55% after five cycles), which was superior to most similar adsorbents reported till date. Such improvement is explored to mainly originate from two respects: the physical adsorption facilitated by the abundant pores formed through the stacking and growth of CuFe2O4 and MgFe2O4, and the chemisorption resulting from surface complexation and hydrogen bonding between the MMOs and CR. This strategy to directly transform ES into functional materials shows great promise both in waste management and preparation of robust adsorbents for wastewater treatment.

Dechlorination of 2,4-dichlorophenol by Fe/Ni nanoparticles: the pathway and the effect of pH and the Ni mass ratio

ABSTRACTThe dechlorination of 2,4-dichlorophenol (2,4-DCP) by a nanoscale Fe/Ni material was investigated at room temperature. 2,4-DCP can be removed more quickly by an Fe/Ni material with 2% Ni. Fe/Ni exhibited excellent adsorption and reduction efficiency toward 2,4-DCP in an aqueous solution over a wide range of pH values. The removal rate of 2,4-DCP exceeded 95% in 60 min in the pH range of 3.0-9.0, and more than 75% was dechlorinated to phenol (CA). The degradation pathway of 2,4-DCP was confirmed based on analysis of the intermediate and end products. A portion of 2,4-DCP was first dechlorinated with a chlorine atom to produce 2-chlorophenol and 4-chlorophenol, and then dechlorination was performed sequentially to form CA. The other portion of 2,4-DCP was dechlorinated to remove two chlorine atoms simultaneously to generate CA. The investigations are essential to the application of iron-based remediation technology.

Interplay between Facets and Defects during the Dissociative and Molecular Adsorption of Water on Metal Oxide Surfaces

Surface terminations and defects play a central role in determining how water interacts with metal oxides, thereby setting important properties of the interface that govern reactivity such as the type and distribution of hydroxyl groups. However, the interconnections between facets and defects remain poorly understood. This limits the usefulness of conventional notions such as that hydroxylation is controlled by metal cation exposure at the surface. Here, using hematite (α-Fe₂O₃) as a model system, we show how oxygen vacancies overwhelm surface cation-dependent hydroxylation behavior. Synchrotron-based ambient-pressure X-ray photoelectron spectroscopy was used to monitor the adsorption of molecular water and its dissociation to form hydroxyl groups in situ on (001), (012), or (104) facet-engineered hematite nanoparticles. Supported by density functional theory calculations of the respective surface energies and oxygen vacancy formation energies, the findings show how oxygen vacancies are more prone to form on higher energy facets and induce surface hydroxylation at extremely low relative humidity values of 5 × 10^-5%. When these vacancies are eliminated, the extent of surface hydroxylation across the facets is as expected from the areal density of exposed iron cations at the surface. These findings help answer fundamental questions about the nature of reducible metal oxide-water interfaces in natural and technological settings and lay the groundwork for rational design of improved oxide-based catalysts.

Unique amorphous/crystalline heterophase coupling for an efficient oxygen evolution reaction

Designing amorphous/crystalline heterophase catalysts is still in the initial stage, and the study of amorphous/crystalline heterophase and carbon-free catalysts has not yet been realized. Herein, we report a unique amorphous/crystalline heterophase catalyst consisting of NiFe alloy nanoparticles (NPs) supported on Ti₄O₇ (NiFe/Ti₄O₇) for the first time, which is achieved by a heterophase supporting strategy of dual heat treatment. Surprisingly, the amorphous/crystalline heterophase is flexibly composed of amorphous and crystalline phases of alloy NPs and Ti₄O₇. The heterophase coupling endows the catalyst with a low overpotential (256 mV at 10 mA cm^-2), a small Tafel slope (47 mV dec^-1) and excellent endurance stability (over 100 h) in 1 M KOH electrolyte, which already outperforms commercial RuO₂ (338 mV and 113 mV dec^-1) and exceeds most reported representative carbon-based and titanium-based non-precious metal catalysts. The density functional theory (DFT) calculations and experimental results reveal that the unique amorphous/crystalline heterophase coupling in NiFe/Ti₄O₇ results in electron transfer between the alloy NPs and Ti₄O₇, allowing more catalytically active sites and faster interfacial electron transfer dynamics. This work provides insights into the synthesis of amorphous/crystalline heterophase catalysts and can be generalized to the heterophase coupling of other transition metal-based electrocatalysts.