Isotherm, kinetic, and thermodynamic studies on the adsorption behavior of malachite green dye onto montmorillonite clay

Monte Carlo, molecular dynamic, and experimental studies of the removal of malachite green using g-C3N4/ZnO/Chitosan nanocomposite in the presence of a deep eutectic solvent

Deep-eutectic solvents (DES) have emerged as promising candidates for preparing nanocomposites. In this study, a DES-based graphitic carbon nitride (g-C3N4)/ZnO/Chitosan (Ch) nanocomposite was synthesized to remove malachite green (MG) dye from water. The DES was prepared by mixing and heating citric acid as a hydrogen bond acceptor and lactic acid as a hydrogen bond donor. This is the first report of the removal of MG using DES-based nanocomposites. Experiments on kinetics and isothermal adsorption were conducted to systematically explore the adsorption performances of nanocomposite toward dye. At 25 °C, the highest adsorption performance was obtained with alkaline media (>90 % removal). The greatest adsorption capacity (qm) was 59.52 mg g-1 at conditions (30 mg L-1 MG solution, pH 9, 3 mg nanocomposite per 10 mL of MG solution, 25 °C, 150 rpm, and 150 min) based on the calculation from the best-fitting isotherm model (Langmuir). The adsorption process was most appropriately kinetically described by the PSO model. The Monte Carlo (MC) and molecular dynamic (MC) results are correlated with experimental findings to validate the theoretical predictions and enhance the overall understanding of the adsorption process. Electronic structure calculations reveal the nature of interactions, including hydrogen bonding and electrostatic forces, between the nanocomposite and MG molecules.

New combined experimental and DFT studies for adsorption of sole Azo-dye or binary cationic dyes from aqueous solution

Textile-toxic synthetic dyes, which possess complex aromatic structures, are emitted into wastewater from various branches. To address this issue, the adsorption process was applied as an attractive method for the removal of dye contaminants from water in this article. An unprecedented integrated experimental study has been carried out, accompanied by theoretical simulations at the DFT-B3LYP/6-31G (d,P) level of theory to investigate how single Maxilon Blue GRL (MxB) dye or and its mixture with MG (Malachite Green) dyes interact with the adsorbent and compare the obtained results with the data obtained through experimentation. The full geometry optimization revealed the physical adsorption of dyes on the Al2O3 surface. Non-linear optical properties (NLO) results emphasized that the complex MG-Al2O3-MxB is a highly promising material in photo-applications, and the adsorbed binary system is energetically more favorable compared to the adsorbed sole dye system. The experimental results for (MxB) dye adsorption onto γ-Al2O3 affirmed that the optimum conditions to get more than 98% uptake were at dye concentration 100 ppm, pH 10, adsorbent content 0.05 g, and equilibrium time only 20 min. The kinetic and isothermal studies revealed that the adsorption accepted with the pseudo-second-order and Freundlich isotherm model, respectively. The removal efficiency of the mixture of MxB and MG dyes was the highest but did not change clearly with increasing the % of any of them. The details of the interaction mechanisms of the sole and binary dyes were proven.

Treatment of aqueous phase from hydrothermal liquefaction of municipal sludge by adsorption: Comparison of biochar, hydrochar, and granular activated carbon

Hydrothermal liquefaction (HTL) is promising for treating waste with high moisture, such as municipal sludge, and producing biocrude (a petroleum-like biofuel). However, a large amount of wastewater byproduct, HTL aqueous, is generated. The presence of hazardous compounds (e.g., phenolic compounds and nitrogenous organics) makes HTL aqueous the biggest bottleneck for full-scale implementation at treatment plants. This study investigated the adsorption of various pollutants, focusing on chemical oxygen demand (COD), in HTL aqueous to granular activated carbon (GAC), biochar, and hydrochar. It assessed the effect of pH, temperature, time, and adsorbent concentration on adsorption efficiency and identified proper adsorbent and process conditions for removing most of the pollutants from HTL aqueous. GAC showed the highest adsorption capacity (184 mg/g) for COD, surpassing biochar (44 mg/g) and hydrochar (42 mg/g). The adsorption of COD to all adsorbents followed pseudo-second-order kinetic and Freundlich isotherm, suggesting that the adsorption of HTL aqueous pollutants is a heterogeneous and multilayer process, limited by chemosorption. The adsorption was endothermic, favored by elevated temperatures and neutral pH. This means adsorption is more efficient and economical for treating HTL aqueous that is a hot stream at the large-scale and it saves chemical needs. Lastly, GAC was highly efficient and selective in removing harmful pollutants, such as COD (up to 66%), total phenolic compounds (up to 94%), pyrazines (up to 99%), pyridines (up to 100%), and cyclic ketones (up to 95%) while preserving valuable volatile fatty acids (VFAs) and ammonia for subsequent recovery. Removal of potentially inhibitory compounds and preserving VFAs are crucial for carbon recovery in anaerobic biological treatment of HTL aqueous. The results suggested the necessity of optimizing adsorbent dose for maximizing removal of specific group of inhibitory compounds in full-strength HTL aqueous for enhancing downstream biological treatment. Lastly, this study established the groundwork for HTL aqueous adsorption, elucidating its effectiveness and mechanism for pollutant removal.

Insights on applications of bentonite clays for the removal of dyes and heavy metals from wastewater: a review

In recent decades, increased industrial, agricultural, and domestic activities have resulted in the release of various pollutants into the aquatic systems, which require a reliable and environmentally friendly method to remove them. Adsorption is one of the most cost-effective and sustainable wastewater treatment techniques. A plethora of low-cost bio-based adsorbents have been developed worldwide so far to supplant activated carbon and its high processing costs. Bentonite clays (BCs), whether in natural or modified form, have gained enormous potential in wastewater treatment and have been used successfully as a novel and cost-effective bio-sorbent for removing organic and inorganic pollutants from the liquid suspension. It has become a sustainable solution for wastewater treatment due to its variety of surface and structural properties, superior chemical stability, high capacity for cation exchange, elevated surface area due to its layered structure, non-toxicity, abundance, low cost, and high adsorption capacity compared to other clays. This review encompasses comprehensive literature about various modification techniques and adsorption mechanisms of BCs concerning dyes and heavy metal removal from wastewater. A critical overview of different parameters for optimizing adsorption capacity and regeneration via the desorption technique has also been presented here. Finally, a conclusion has been drawn with some future research recommendations based on technological challenges encountered in industrializing these materials.

Adsorption of Cationic Contaminants by Cyclodextrin Nanosponges Cross-Linked with 1,2,3,4-Butanetetracarboxylic Acid and Poly(vinyl alcohol)

Cationic organic pollutants (dyes and pesticides) are mainly hydrosoluble and easily contaminate water and create a serious problem for biotic and abiotic species. The elimination of these dangerous contaminants from water was accomplished by adsorption using cyclodextrin nanosponges. These nanosponges were elaborated by the cross-linking between 1,2,3,4-butanetetracarboxylic acid and β-cyclodextrin in the presence of poly(vinyl alcohol). Their physicochemical characteristics were characterized by gravimetry, acid-base titration, TGA, 13C NMR, ATR-FTIR, Raman, X-ray diffraction, and Stereomicroscopy. The BP5 nanosponges displayed 68.4% yield, 3.31 mmol/g COOH groups, 0.16 mmol/g β-CD content, 54.2% swelling, 97.0% PQ removal, 96.7% SO removal, and 98.3% MG removal for 25 mg/L of initial concentration. The pseudo-second-order model was suitable for kinetics using 180 min of contact time. Langmuir isotherm was suitable for isotherm with the maximum adsorption of 120.5, 92.6, and 64.9 mg/g for paraquat (PQ), safranin (SO), and malachite green (MG) adsorption, respectively. Finally, the reusability performance after five regeneration times reached 94.1%, 91.6%, and 94.6% for PQ, SO, and MG adsorption, respectively.

Sorption and recovery of phenolic compounds from aqueous phase of sewage sludge hydrothermal liquefaction using bio-char

Bio-char, a by-product of thermochemical conversion processes, has a great potential in phenolic compounds sorption from the waste aqueous phase produced from the hydrothermal liquefaction (HTL) process while being a low-cost sorbent. This study investigated the effect of temperature, pH, bio-char concentration, and mixing speed on two types of bio-char sorption of phenolic compounds using Taguchi's design of experiment and response surface method. Isothermal kinetics and thermodynamic properties were also evaluated to explain the sorption mechanism. The experimental results were well described by the pseudo-second-order kinetic model for both types of bio-char. The Langmuir isotherm model was found to be more suitable at high sorption temperatures, while the Freundlich isotherm model was better at low temperatures. Finally, the alkaline desorption and regeneration experiments were examined, and the eluents with phenolic compounds were characterized using a liquid chromatography-mass spectrometer.

Green antimicrobial adsorbent containing grafted xanthan gum/SiO2 nanocomposites for malachite green dye

Recently, removal of synthetic dyes, especially cationic dye of malachite green (MG), and inhibition of the growth of pathogenic microorganism from drinking water have gained much interest due to their high toxic potency for aquatic biosystems. Herein, a new dye adsorbent with outstanding antibacterial activity was fabricated based on xanthan gum (XG) and SiO₂ nanoparticles through ultrasonication followed by the crosslinking polymerization with vinyl imidazole monomer. The nano adsorbents were characterized with various techniques such as FTIR, XRD, SEM, EDX, and TEM. The nanocomposites were applied as a filter for discarding MG dye and killing the growth of bacterial strains such as E.coli and S.aureus which are considered as the common impurities for drinking water. The data revealed that a maximum adsorption capacity was recorded as 99.5% (Q_max = 588.2 mg/g) at optimum conditions including 10 mg nanocomposite, 10 mL of MG dye (450 ppm), pH = 7, the temperature of 30 °C, and the adsorption time was adjusted within 6 h. The process of dye adsorption was applied to the common isotherm models of Langmuir, Temkin, and Freundlich, and the findings showed that the adsorption behavior was well fitted with the Langmuir one (R² = 0.9983). Moreover, different adsorption kinetic models such as pseudo-first order, pseudo-second order, and intra-particle diffusion were studied for understanding the mechanism of MG adsorption onto nanocomposite surface. It was found that both intraparticle diffusion and pseudo-first-order have participated evenly in the adsorption mechanism of MG dye. Ultimately, the as-prepared nanocomposites were tested against the growth of S. aureus, and E.coli manifesting a superior inhibition diameter as 23.5 ± 0.50, and 25.33 ± 0.47 mm against E.coli, and S. aureus, respectively. Therefore, our new XG-g-PVI/SiO₂ adsorbent is a very promising adsorbent for the fast and efficient capture of dyes from aqueous solutions.

A reusable mesoporous adsorbent for efficient treatment of hazardous triphenylmethane dye wastewater: RSM-CCD optimization and rapid microwave-assisted regeneration

In this research, mesoporous calcium aluminate nanostructures (meso-CaAl2O4) were synthesized using a citric acid-assisted sol-gel auto-combustion process as the potential adsorbent to eliminate toxic triphenylmethane dye malachite green (MG) from synthetic/real effluent. The surface morphology of meso-CaAl2O4 was highly porous with nanometric size and non-homogeneous surface. The specific surface area, total pore volume, and BJH pore diameter of meso-CaAl2O4 were 148.5 m2 g-1, 1.39 cm3 g-1, and 19 nm, respectively. The meso-CaAl2O4 also showed a very high heat resistance, due to losing only 7.95% of its weight up to 800 °C, which is mainly related to the moisture loss. The optimal adsorption conditions were obtained based on response surface methods (RSM)-central composite design (CCD) techniques. The Langmuir isotherm model was used for fitting the adsorption measurements, which presented 587.5 mg g-1 as the maximum adsorption capacity of the dye. The data obtained from the adsorption kinetics model were found to correspond to the pseudo-second-order model. Also, the thermodynamic parameters including enthalpy change (ΔH°), entropy change (ΔS°), and Gibbs free energy change (ΔG°) indicated that MG dye adsorption by the meso-CaAl2O4 was feasible, endothermic, and occurred spontaneously. Furthermore, the meso-CaAl2O4 was regenerated by microwave irradiation under 900 W at 6 min, and the MG dye removal efficiency was remained over 90% after the five cycles of microwave regeneration.

Adsorption of Malachite Green Dye onto Mesoporous Natural Inorganic Clays: Their Equilibrium Isotherm and Kinetics Studies

Contamination of water with organic dyes is a major environmental concern as it causes serious life-threatening environmental problems. The present research was designed to evaluate the potential of three different natural inorganic clays (NICs) i.e., Pakistani bentonite clay (PB), bentonite purchased from Alfa Aesar (BT), and Turkish red mud (RM) for malachite green (MG) dye removal from an aqueous solution. Various analytical techniques, namely X-ray fluorescence spectrometry (XRF), X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), Brunauer–Emmett–Teller surface area measurement (BET), and thermogravimetric analysis (TGA), were used to investigate the physicochemical properties of the NICs samples. The effect of adsorption operational parameters such as contact time, aqueous phase pH, dye concentration, and amount of NICs on the adsorption behavior of MG onto NICs samples were investigated under the batch adsorption system. The equilibrium and kinetic inspection reflected the best description of MG adsorption behavior by the Langmuir isotherm model and pseudo-first-order kinetic model, respectively. The results indicated that the adsorption was favorable at higher pH. The maximum adsorption capacities calculated by Langmuir isotherm for PB, BT, and RM were found to be 243.90 mg/g, 188.68 mg/g, and 172.41 mg/g, respectively. It can be concluded that natural inorganic clays with a higher surface area can be used as an effective adsorbent material to remove the MG dye from an aqueous solution.

Innovative bactericidal adsorbents containing modified xanthan gum/montmorillonite nanocomposites for wastewater treatment

Herein, we reported the preparation of novel antibacterial nanocomposites based on biodegradable polymers. The nanocomposites were applied as capable adsorbent for removing of malachite green (MG) dye, as well as inhibiting of E. coli and S. aureus growth as the most common pollutants for water. The grafted xanthan gum with poly(vinylimidazole) (XG-g-PVI) nanocomposites were synthesized in the presence of different Montmorillonite (MMT) nanoclays concentrations (1%, 3% and 5%). The prepared modified XG nanocomposites were detected through XRD, SEM-EDX, FTIR and TEM. The maximum adsorption MG capacity was determined as 99.99% (909.1 mg/g) in basic medium at 30 °C for 90 min. The adsorption isotherm for removal of MG dye was studied against different models like Langmuir, Freundlich, Temkin, FloryHuggins isotherm models, however, the adsorption results were good fitted with Langmuir isotherm model (R² = 0.9942). Additionally, various adsorption kinetic models: pseudo-first order, second order, pseudo-second order, and intra-particle diffusion models were studied for adsorption mechanism of MG dye on top of prepared nanocomposite surface. Finally, the antibacterial activity outcomes displayed that the prepared XG-g-PVI/MMT nanocomposites had excellent inhibition growth for bacteria and the antibacterial activity increased abruptly with the increased of MMT nanoclay concentrations.

Adsorption and regeneration of leaf-based biochar for p-nitrophenol adsorption from aqueous solution

As an environmentally friendly and low-cost adsorbent, biochar has great potential in wastewater treatment. This study investigated biochar derived from Platanus orientalis L. leaves (PLB) activated by KOH in terms of its capacity and reusability to adsorb p-nitrophenol (PNP). PLB had a large specific surface area and total pore volume, and exhibits good PNP removal with a maximal adsorption capacity of 622.73 mg g-1 at 298 K. Batch experiments showed that PLB had a high PNP adsorption capacity under acidic conditions. Experimental results were well described by the pseudo-second-order kinetic model and the Langmuir adsorption isotherm model. The thermodynamic study showed that PNP adsorption was a spontaneously exothermic process, and increasing temperature was not conducive to adsorption. In addition, PNP adsorption was mainly attributed to hydrophobic interaction. The regeneration experiment showed that PLB had good reusability. After the fifth regeneration, the adsorption capacity of PLB still reached 557.05 mg g-1. The deactivation of oxygen-containing functional groups and pore blockage were the causes for the decrease in adsorption capacity of the recycled PLB. Moreover, the biochar showed good adsorption efficiency and reusability, thereby suggesting its potential to serve as an efficient PNP adsorbent for wastewater treatment.

Removal of chromium (VI) from water by porous carbon derived from corn straw: Influencing factors, regeneration and mechanism

Porous carbon is one of the most widely used materials to remove Cr(VI) from polluted water. Here we reported one efficient porous carbon material prepared from corn straw. The results of Fourier transform infrared spectroscopy (FTIR), Energy dispersion spectrum (EDS), and X-ray photoelectron spectroscopy (XPS) indicated that the porous carbon surface had functional groups such as COOH, OH and COC, etc, which could be acted as active sites during the adsorption process. Brunauer-Emmett-Teller (BET) results showed that the surface area and total pore volume of the adsorbent were 2131.181 m²/g and 1.128 cm³/g, respectively. The percentages of micropore surface area and micropore volume achieved 91.93% and 80.43%, respectively. The maximum adsorption capacity of Cr(VI) was 175.44 mg/g at 25 °C with the well-developed microporous structure and abundant oxygen-containing functional groups of porous carbon. The adsorption process was well described by the pseudo-second order model and Langmuir adsorption isotherm model. It was mainly based on chemical adsorption of a single molecular layer, accompanied by ion exchange reaction, Cr(VI) reduction, and complexation, etc. The adsorbent exhibited excellent removal performance of Cr(VI) in the co-existing ions wastewater and electroplating wastewater, and could remain high removal performance for four adsorption-desorption cycles.

Removal of anionic dyes from an aqueous solution by a magnetic cationic adsorbent modified with DMDAAC

Fe₃O₄@SiO₂modified with quaternary ammonium groups was prepared to remove methyl blue from aqueous solutions and exhibited good reusability.

Removal of dye molecules from aqueous solution by carbon nanotubes and carbon nanotube functional groups: critical review

Scheme for the adsorption of dye molecules by CNTs and CNT functionality.