Using D-optimal experimental design to optimise remazol black B mineralisation by Fenton-like peroxidation

Taguchi L16 (44) orthogonal array-based study and thermodynamics analysis for electro-Fenton process treatment of textile industrial dye

Reactive orange 16 (RO16) is the most widely used azo dye in Textile industry. Complex aromatic structures and resistivity to biological decay caused the dye pollutants incompletely treated by the conventional oxidative methods. The current study presents the electro-Fenton-based advanced oxidation treatment of RO16 dye and the process optimization by Taguchi-based design of experiment (DOE). Using a 500 mL volume lab-scale experimental setup, the process was first studied for the principal operational parameters (initial dye concentration (q); [H2O2]/[Fe+2] (R); current density (ρ); and temperature (T)) effect on decolourization (D R ) and COD removal (C R ). Then, by means of the L16 (44) orthogonal array (OA) formation, standard mean and signal-to-noise (S/N) ratio, the process was optimized for the response variables. The result showed the optimized result at q = 100 mg/L, R = 100, ρ = 8 mA/cm2, and T = 32 °C; with D R and C R as 90.023 and 84.344%, respectively. It was found that the current density affects the process most, followed by [H2O2]/[Fe+2] ratio, initial dye concentration, and temperature i.e., ρ > R > q > T. Also, with the analysis of variance (ANOVA), model equations for D R and C R were developed and its accuracy was verified for experimental results. At optimized conditions, the first order removal rate constants (k a ) were found from batch results. Additionally, the thermodynamic constants (ΔH e , ΔS e , and ΔG b ) were also calculated for the nature of heat-energy involved and temperature effect study on dye degradation. The results showed that the process was thermodynamically feasible, endothermic, and non-spontaneous with a lower energy barrier (E A  = 46.7 kJ mol−1).

Surfactant-assisted synthesis of copper oxide nanorods for the enhanced photocatalytic degradation of Reactive Black 5 dye in wastewater

In this study, copper oxide nanorods were synthesized via surfactant-assisted chemical precipitation method and characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and UV-Visible spectrometer. XRD result reveals that CuO nanorods were structured in the monoclinic phase. SEM image suggested that synthesized CuO were shaped like nanorod with approximately 20-40 nm width and 500-800 nm length. The observed band gap calculated from UV-Visible absorption studies is 1.45 eV. As-prepared CuO nanorods were applied as a photocatalyst for the degradation of textile dye Reactive Black 5 (RB-5) in aqueous solution under the presence of visible light. The result exhibited that an enhanced degradation of RB-5 was achieved around 98% within 300 min and the experimental values were well matched with the linear fit model (R² = 0.97) and the observed rate constant found to be 5 × 10^-3 min^-1. Therefore, as-synthesized CuO nanorods can be applied as a potential photocatalyst material for the degradation of organic pollutants in the wastewater.

Solar photocatalytic degradation of 2-chlorophenol with ZnO nanoparticles: optimisation with D-optimal design and study of intermediate mechanisms

In this study, the photocatalytic degradation of toxic pollutant (2-chlorophenol) in the presence of ZnO nanoparticles (ZnO NPs) was investigated under solar radiation. The three main factors, namely pH of solution, solar intensity and calcination temperature, were selected in order to examine their effects on the efficiency of the degradation process. The response surface methodology (RSM) technique based on D-optimal design was applied to optimise the process. ANOVA analysis showed that solar intensity and calcination temperature were the two significant factors for degradation efficiency. The optimum conditions in the model were solar intensity at 19.8 W/m², calcination temperature at 404 °C and pH of 6.0. The maximum degradation efficiency was predicted to be 90.5% which was in good agreement with the actual experimental value of 93.5%. The fit of the D-optimal design correlated very well with the experimental results with higher values of R ² and R ²_adj correlation coefficients of 0.9847 and 0.9676, respectively. The intermediate mechanism behaviour of the 2-chlorophenol degradation process was determined by gas chromatography-mass spectrometry (GC-MS). The results confirmed that 2-chlorophenol was converted to acetic acid, a non-toxic compound.

Development of an advanced chemical oxidation wastewater treatment system for the batik industry in Malaysia

Symmetric representation of the Fenton oxidation batch system for the treatment of highly recalcitrant batik wastewater.

Mineralization of hetero bi-functional reactive dye in aqueous solution by Fenton and photo-Fenton reactions

This study focused on the advanced oxidation of the hetero bi-functional reactive dye Sumifix Supra Yellow 3RF (CI Reactive Yellow 145) using dark Fenton and photo-Fenton conditions in a lab-scale experiment. A 2(3) factorial design was used to evaluate the effects of the three key factors: temperature, Fe(II) and H2O2 concentrations, for a dye concentration of 250 mg L(-1) with chemical oxygen demand (COD) of 172 mg L(-1) O2 at pH=3. The response function was the COD reduction. This methodology lets us find the effects and interactions of the studied variables and their roles in the efficiency of the treatment process. In the optimization, the correlation coefficients for the model (R2) were 0.948 and 0.965 for Fenton and photo-Fenton treatments, respectively. Under optimized reaction conditions: pH=3, temperature=298 K, [H2O2]=11.765 mM and [Fe(II)]=1.075 mM; 60 min of treatment resulted in a 79% and 92.2% decrease in COD, for the dye taken as the model organic compound, after Fenton and photo-Fenton treatments, respectively.

Degradation performance and cost implication of UV-integrated advanced oxidation processes for wastewater treatments

Advanced oxidation processes (AOPs) are commonly used for treating recalcitrant wastewater with varying degree of efficiency, depending on several operating parameters. In this review, a comparative study among selected AOPs integrated with ultraviolet (UV) (UV/Fenton, UV/H

A comparison of central composite design and Taguchi method for optimizing Fenton process

In the present study, a comparison of central composite design (CCD) and Taguchi method was established for Fenton oxidation. [Dye]_ini, Dye : Fe⁺², H₂O₂ : Fe⁺², and pH were identified control variables while COD and decolorization efficiency were selected responses. L₉ orthogonal array and face-centered CCD were used for the experimental design. Maximum 99% decolorization and 80% COD removal efficiency were obtained under optimum conditions. R squared values of 0.97 and 0.95 for CCD and Taguchi method, respectively, indicate that both models are statistically significant and are in well agreement with each other. Furthermore, Prob > F less than 0.0500 and ANOVA results indicate the good fitting of selected model with experimental results. Nevertheless, possibility of ranking of input variables in terms of percent contribution to the response value has made Taguchi method a suitable approach for scrutinizing the operating parameters. For present case, pH with percent contribution of 87.62% and 66.2% was ranked as the most contributing and significant factor. This finding of Taguchi method was also verified by 3D contour plots of CCD. Therefore, from this comparative study, it is concluded that Taguchi method with 9 experimental runs and simple interaction plots is a suitable alternative to CCD for several chemical engineering applications.