Removal of arsenic from aqueous solutions using waste iron columns inoculated with iron bacteria

The Comprehensive Health Risk Assessment of Polish Smelters with Ecotoxicological Studies

Air pollution connected to smelter activity can significantly deteriorate the quality of soil due to the precipitation of rain or simple deposition of the air particulates into the ground. Hence, in this study, we focused on the analysis of the soil which can inform us about the general state of the environment in the area and the possible health hazard for humans. If the top layer of the soil is in bad condition, it can indicate that air pollution in the area is also not in good condition, and the lives of the inhabitants of these areas can be at serious risk. To comprehensively identify the level of contamination in the soils from the areas of Polish smelters, studies of the concentration of potentially toxic elements (PTEs) in the soil were conducted. On the basis of the obtained results, health risk assessment was performed to verify the possible influence on human health. The results showed that the non-carcinogenic risk existed only for Oława, while the possibility of the carcinogenic risk occurred in all of the studied places. The outcome is very disturbing and certain steps must be undertaken in order to protect the lives of the inhabitants. Additionally, in order to assess the suitability of soils for the cultivation of edible plants, phytotoxicity tests were conducted. The obtained results revealed that in all the studied areas, a visible inhibition of roots and shoots can be observed. The conducted study indicated the most polluted regions and the possible health hazard, and it can provide the general information about the impact of smelters on the environment.

The Effect of Arsenic on the Photocatalytic Removal of Methyl Tet Butyl Ether (MTBE) Using Fe2O3/MgO Catalyst, Modeling, and Process Optimization

MTBE is an aliphatic matter successfully removed from contaminated water by an advanced oxidation process. Additionally, arsenic is a toxic metalloid that is detected in some water supplies, such as in Iran. Concerning the oxidation potential of arsenic in an aqueous solution, it is expected that its interference in the photocatalytic removal of organic matter includes MTBE. Nevertheless, there is a lack of observation of this effect. In this study, the effect of arsenic on the photocatalytic removal of MTBE using an Fe2O3/MgO catalyst under UV radiation was investigated. Using an experimental design, modeling, and optimizing operational parameters, such as the arsenic and MTBE concentrations, catalyst dosage, pH, and reaction time, were studied. The synthesized nanocatalyst had a uniform and spherical morphological structure and contained 33.06% Fe2O3 and 45.06% MgO. The results indicate that the best model is related to the quadratic (p-value < 0.0001, R2 = 0.97) and that the effect of the MTBE concentration is greater than the others. The highest removal efficiency was taken in an initial concentration of 37.5 mg/L MTBE, 1.58 mg/L Fe2O3/MgO, pH 5, and a reaction time of 21.41 min without any As. The removal efficiency was negatively correlated with the initial MTBE concentration and pH, but it was positively associated with the Fe2O3/MgO dosage and reaction time. Finally, the presence of arsenic decreased the removal efficiency remarkably (90.90% As = 0.25 μg/L and 61% As = 500 μg/L). Consequently, MTBE was removed by the photocatalytic process caused by Fe2O3/MgO, but the presence of arsenic was introduced as a limiting factor. Therefore, pretreatment for the removal of arsenic and more details of this interference effect are suggested.

Arsenate removal from contaminated water using Fe2O3-clinoptilolite powder and granule

Natural clinoptilolite (Clin) was modified with iron oxide using three different methods including precipitation, wet-impregnation and ion-exchange and then the modified adsorbent with highest As(V) removal efficiency was encapsulated into Alginate by a simple cross-linking method to obtain Fe-Clin granules. The surface morphology and chemical composition of the Fe-Clin sorbents were characterized by scanning electron microscope and X-ray diffraction analysis. The selected Fe-Clin powders and granules possessed enhanced affinity towards the highly toxic arsenic pollutant in a very short time. Batch adsorption experiments showed that the Fe-Clin adsorbent can be widely used within a wide range of pH (2-9). In addition, to reach a high removal percentage (over 90%) of As(V), the optimum dosage of powder and granule shaped adsorbents was obtained as 0.1 and 0.6 g L^-1, respectively. Both adsorbents could successfully remove As(V) in a very short amount of time as 20 and 30 min in the case of powders and granules, respectively. The maximum adsorption capacity of Fe-Clin granules evaluated by using Langmuir adsorption isotherm was found to be 11.17 mg g^-1. By testing the granules in a circulated fluidized column experiment, it was demonstrated that Fe-Clin granules could remove As(V) up to an acceptable level (93%) within 10 min. This study demonstrates that Fe-Clin granules, obtained by exploiting natural clinoptilolite, iron oxide and alginate, are efficient, sustainable and fairly cheap adsorbents for the removal of arsenate from the aquatic environment in a very short contact time.

Effect of simulated acid rain on stability of arsenic calcium residue in residue field

In recent years, acid rain had a serious negative impact on the leaching behavior of industrial waste residue. Researches were mainly focused on the environmental hazards of heavy metal in the leachate, but ignored the effects of heavy metal speciation on the stability of waste residue in the subsequent stabilization process. In this study, the unstable calcium-arsenic compounds in the arsenic calcium residue were firstly removed by leaching process; subsequently, the crystallization agent was added to treat the remaining calcium-arsenic mixture. The results of the leaching process demonstrated that the decrease in particle size and pH value directly affected the increase in the cumulative leaching amount of arsenic, and the cumulative leaching ratio reached 1.55%. In addition, the concentration of arsenic decreased from 3583 to 49.1 mg L^-1. After the crystallization process, the arsenic concentration was lower than the limit value of Identification Standards for Hazardous Wastes (GB 5085.3-2007). The SEM analysis showed the bulk structures, and XRD pattern confirmed that they were the stable compounds. Moreover, the result of XRD and SEM illustrated that acid concentration, chloride ions and sulfate ions were contributed to the transformation and growth of stable calcium arsenate compounds. Therefore, effective control of the acidity of acid rain, the type of anions in acid rain, and the particle size of residues would contribute to adjusting the arsenic speciation to be more stable. The leaching-crystallization process was of great significance to improve the stability of the arsenic-containing residue.

Arsenic Removal from Mining Effluents Using Plant-Mediated, Green-Synthesized Iron Nanoparticles

Arsenic contamination in industrial and mining effluents has always been a serious concern. Recently, nano-sized iron particles have been proven effective in sorptive removal of arsenic, because of their unique surface characteristics. In this study, green synthesis of iron nanoparticles was performed using a mixed extract of two plant species, namely Prangos ferulacea and Teucrium polium, for the specific purpose of arsenic (III) removal from the aqueous environment. Results of UV-visible spectrometry, X-ray powder diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) analyses confirmed the formation of iron nanoparticles from Prangos ferulacea (Pf) and Teucrium polium (Tp) extracts. The synthesized Fe nanoparticles morphology was studied via microscopy imaging. The particle size was 42 nm, as assessed by dynamic light scattering (DLS) analysis. Adsorption experiments were also designed and performed, which indicated 93.8% arsenic removal from the aqueous solution at 200 rpm agitation rate, 20 min agitation time, pH 6, initial concentration of 0.1 g/L, and adsorbent dosage of 2 g/L. Adsorption isotherm models were investigated, and the maximum uptake capacity was determined to be about 61.7 mg/g. The kinetic data were best represented by the pseudo-second kinetic model (R2 = 0.99). The negative value of Gibbs free energy, the enthalpy (−7.20 kJ/mol), and the entropy (−57 J/mol.K) revealed the spontaneous and exothermic nature of the adsorption process. Moreover, the small quantity of the activation energy confirmed the physical mechanism of arsenic adsorption onto iron nanoparticles and that the process is not temperature sensitive.

The application of plant growth regulators to improve phytoremediation of contaminated soils: A review

Soil contamination is one of the most important environmental problems around the world. The transfer of organic contaminants and heavy metals to the food chain is a major threat to human health. Purging these contaminants often involves a lot of energy and complex engineering processes. Phytoremediation technology can be used in various environments, such as water, soil, and air, to reduce or eliminate different contaminants. The major mechanisms involved in phytoremediation include plant extraction, rhizofiltration, plant evaporation, plant stabilization, plant decomposition, and rhizosphere degradation. The efficiency of phytoremediation can be increased through using chelating and acidifying agents, applying electric current in the soil, using organic chemicals and fertilizers, planting transgenic plants, using bacteria, and applying plant growth regulators. Recently, the use of plant growth regulators has been investigated as a suitable method for improving the efficacy of phytoremediation. Effective plant growth regulators to improve phytoremediation include auxins, gibberellins, cytokinins, and salicylic acid. The activity of these materials depends on their concentration, environmental factors that affect their absorption, and the physiological state of the plant. Using these materials increases the biomass of the plant and reduces the negative effects of the presence of contaminants in the plant. The present study aimed to review the latest studies performed on the improvement of phytoremediation using plant growth regulators and their mechanisms.

Integrated bio-oxidation and adsorptive filtration reactor for removal of arsenic from wastewater

Recently, removal of arsenic from different industrial effluent discharged using simple, efficient and low-cost technique has been widely considered. In this study, removal of arsenic (As) from real wastewater has been studied employing modified bio-oxidation followed by adsorptive filtration method in a novel continuous flow through the reactor. This method includes biological oxidation of ferrous to ferric ions by immobilized Acidothiobacillus ferrooxidans bacteria on granulated activated carbon (GAC) in fixed bed bio-column reactor with the adsorptive filtration unit. Removal efficiency was optimized regarding the initial flow rate of media and ferrous ions concentration. Synthetic wastewater sample having different heavy metal ions such as Arsenic (As), Cobalt (Co), Chromium (Cr), Copper (Cu), Iron (Fe), Lead (Pb) and Manganese (Mn) were also used in the study. The structural and surface changes occurring after the treatment process were scrutinized using FT-IR and Scanning Electron Microscopy (SEM) analysis. The finding showed that not only arsenic can be removed considerably in the bioreactor system, but also removing efficiency was much more (<90%) for other heavy metals in real wastewater sample. The results from TCPL test confirms that solid spent media was non-hazardous and can be safely disposed of. This study verified that combination of bio-oxidation with adsorptive filtration method improves the removal efficiency of arsenic and other heavy metal ions in wastewater sample.

Assessment of arsenic removal efficiency by an iron oxide-coated sand filter process

Arsenic is among the most dangerous contaminants which can limit groundwater use for drinking water consumption. Among the most diffused As-removal technologies around the world, adsorptive media systems are usually favored for relatively low cost and simplicity of operation. This study examines the performance of a laboratory-scale iron oxide-coated sand (IOCS) column filter, to remove arsenic (arsenate (As[V]) and arsenite (As[III])) from groundwater. This technology could be adopted in small communities, as it showed consistent removal rates of 99% with an easy-to-operate process. Some considerations about the possible introduction of such technology in developing countries are provided, highlighting the general impacts to human health related to high arsenic concentrations in groundwater. This, among other adsorption processes, could be recommended as a sustainable mean of ensuring good drinking water quality in developing regions, reducing human health impacts.

Effects of brining on the corrosion of ZVI and its subsequent As(III/V) and Se(IV/VI) removal from water

Zero-valent iron (ZVI) has been extensively applied in water remediation, and most of the ZVI materials employed in practical applications are iron scraps, which have usually been corroded to certain extent under different conditions. In this study, the effects of brining with six solutions (NaCl, Na₂SO₄, NaHCO₃, Na₂SiO₃, NH₄Cl, and NaH₂PO₄) on the corrosion of ZVI and its performance in the removal of As(III/V)/Se(IV/VI) were systematically investigated. All the studied solutions enhanced the corrosion of ZVI except for Na₂SiO₃, and the degrees of corrosion followed the order of NH₄Cl > NaH₂PO₄ > Na₂SO₄ > NaCl > NaHCO₃ > H₂O > Na₂SiO₃. The corrosion products derived from ZVI were identified by SEM and XRD, and the dominant corrosion products varied with the type of brine solution. The positive correlation between the degree of ZVI corrosion and As(III/V)/Se(IV/VI) removal by the pre-corroded ZVI (pcZVI) was verified. In addition, As and Se removal by pcZVI was realized via a comprehensive process including adsorption and reduction, as further supported by the XPS analysis. We believe this study will shed new light upon the selection of iron materials pre-corroded under different saline conditions for practical water remediation.