Modified polyether-sulfone membrane: a mini review

Polyether sulfone flat-sheet membrane impregnated with Mn-Al layered double hydroxide nanoparticles for green microfiltration of acrylamide in cocoa products

A new polyether sulfone (PES) membrane modified with manganese-aluminum layered double hydroxide (Mn-Al LDH) was prepared and utilized in the membrane micro-solid phase extraction (M-µSPE) of acrylamide for the first time. The analyses were conducted using HPLC-UV. The extraction efficiency of the PES membrane was enhanced two-fold with the addition of LDH. The fabricated LDH@PES was characterized using ATR-FTIR, SEM, XRD, and nitrogen adsorption/desorption isotherms. The specific surface area, average pore diameter, thickness, cross-sectional channels, and LDH particle size of the LDH@PES membrane were determined. The extraction key factors including membrane composition, desorption conditions, sample pH, and salt concentration were studied. The method was validated by determining the limit of detection, the limit of quantification, linear range, r2, matrix effect, enrichment factor, and precision. Extraction recoveries ranged from 87.4 to 103.5% with RSD < 5.9%. Finally, the method's green features were assessed with the AGREE protocol. This is the first report on the application of LDH@PES for microfiltration/extraction of acrylamide in various chocolate and cocoa products.

Effects of Alkaline Cleaning Agents on the Long-Term Performance and Aging of Polyethersulfone Ultrafiltration Membranes Applied for Treatment of Car Wash Wastewater

The commercial ultrafiltration polyethersulfone (PES) membranes (10 and 100 kDa) blended with polyvinylpyrrolidone (PVP) were applied for the filtration of car wash wastewater. Periodical membrane rinsing with water did not prevent fouling and a decrease in permeate flux was observed. Fouling was reduced by washing the membranes with cleaning agents, which are used in car washes to clean wheels and remove insects. In addition to surfactants, these agents contain NaOH, hence the pH value of cleaning solutions was over 11. Long-term contact with such solutions resulted in the removal of PVP from the membrane matrix and an increase in pore size. The PES membranes were soaked in an alkaline solution (pH = 11.5) for 20 months, after which the 200 kDa dextran rejection decreased from 95% to 80%. To compare with the static degradation conditions, 8 weeks of alkaline agent filtration was realized, after which the dextran (200 kDa) rejection decreased below 50%. This indicated that the cross-flow of alkaline agents can accelerate the removal of components building the membrane matrix. Despite membrane degradation, the separation efficiency (the rejection of chemical oxygen demand-COD, turbidity, and surfactants) during the treatment of synthetic car wash wastewater was similar to that obtained for pristine membranes.

Polyethersulfone Polymer for Biomedical Applications and Biotechnology

Polymers stand out as promising materials extensively employed in biomedicine and biotechnology. Their versatile applications owe much to the field of tissue engineering, which seamlessly integrates materials engineering with medical science. In medicine, biomaterials serve as prototypes for organ development and as implants or scaffolds to facilitate body regeneration. With the growing demand for innovative solutions, synthetic and hybrid polymer materials, such as polyethersulfone, are gaining traction. This article offers a concise characterization of polyethersulfone followed by an exploration of its diverse applications in medical and biotechnological realms. It concludes by summarizing the significant roles of polyethersulfone in advancing both medicine and biotechnology, as outlined in the accompanying table.

CoFe2O4 modified bentonite-based mixed matrix loose nanofiltration membranes for effective wastewater treatment

Mixed-matrix membranes (MMMs) with an ideal polymer/hydrophilic flux enhancer interface considerably recuperates the separation and purification performance of membrane. In this direction, a novel CoFe2O4 functionalized natural clay-bentonite (CoFe2O4@BT) material as a compatible flux enhancer was synthesized for preparation of mixed matrix based in polyethersulfone (PES) matrix. Here, the influences of CoFe2O4@BT on the morphology and performance of the MMMs membranes were systematically investigated using various analytical techniques. Meanwhile, the water flux and sepration eficiency of the CoFe2O4@BT-PES membranes significantly enhanced due to the incorporation of CoFe2O4@BT that altered hydrophilicity, pore and surface characteristic features. The water flux as well as separation efficiency range up to 95%, 94.69%, 94.16% of Congo red (CR), Crystal violet (CV), and humic acid (HA) respectively. Meanwhile, the fouling parameters demonstrated that the CoFe2O4@BT-PES membranes exhibited better antifouling property in the long term experiment comparing with commercial polyamide membrane. CoFe2O4@BT material incorporated membranes showed less decline ratio and a better recovery ratio. The high rejection of dyes with a high permeation flux of the newly designed membranes indicated an amazing possibility for dye purification. In this study, a potential dye mechanism for composite membranes impacted by synthetic CoFe2O4@BT was also put forth. Within the context of application considerations for environmental protection, new materials stock in membranes show good potential for the separation of different organic contaminants.

Post-treatment of soft drink industrial wastewater using a new antibacterial ultra-filtration membrane prepared of Polyethersulfone blended with boehmite-tannic acid-graphene quantum dot

Polymeric membranes have garnered great interest in wastewater treatment; however, fouling is known as their main limitation. Therefore, the blending of hydrophilic nanoparticles in polymeric membranes' structure is a promising approach for fouling reduction. Herein, a hydrophilic boehmite-tannic acid-graphene quantum dot (BM-TA-GQD) nanoparticle was synthesized and blended in a polyethersulfone polymeric membrane in different percentages. The fabricated membranes were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) images, water contact angle, porosity measurement, and antibacterial and antifouling properties. Surface SEM images of the modified membranes showed good dispersion of nanoparticles up to 0.5 wt%, which resulted in hydrophilicity and pure water flux enhancement. Based on AFM images, the mean roughness (Sa) of the fabricated membranes decreased from 2.07 to 0.84 nm for the bare and optimum membranes, respectively. In terms of performance, increasing the nanoparticle percentages up to 0.5 wt% resulted in the flux recovery ratio developing from 44.58% for the bare membrane to 71.35% for the 0.5 wt% BM-TA-GQD/PES membrane (optimum membrane). The antibacterial property of fabricated membranes was studied against biologically treated soft drink industrial wastewater (BTSDIW) as a bacterial source. The results showed that the turbidity of solutions containing permeated wastewater from the modified membranes (0.1, 0.5, and 1 wt% of BM-TA-GQD) was lower than that obtained from the unmodified membrane. These results confirmed the antibacterial properties of fabricated membranes. Finally, the optimal membrane (0.5 wt% BM-TA-GQD) was examined for post-treatment of the BTSDIW. An effluent COD of 13 mg/L and turbidity of 2 NTU showed a successful performance of the filtration process. PRACTITIONER POINTS: Ultrafiltration PES membranes were modified by different loadings of BM-TA-GQD. Hydrophilicity improvement was achieved by adding BM-TA-GQD nanoparticles. Expansion of size and number of macro-voids in modified membranes was confirmed. Membrane roughness was reduced in the BM-TA-GQD blended membranes. The optimum membrane was efficient in COD and turbidity removal.

Development of a New Affinity Gold Polymer Membrane with Immobilized Protein A

New and highly selective stationary phases for affinity membrane chromatography have the potential to significantly enhance the efficiency and specificity of therapeutic protein purification by reduced mass transfer limitations. This work developed and compared different immobilization strategies for recombinant Protein A ligands to a gold-sputtered polymer membrane for antibody separation in terms of functionalization and immobilization success, protein load, and stability. Successful, functionalization was validated via X-ray photoelectron spectroscopy (XPS). Here, a recombinant Protein A ligand was coupled by N-hydroxysuccinimide (NHS)/N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide (EDC) chemistry to carboxy-functionalized, gold-sputtered membranes. We achieved a binding capacity of up to 104 ± 17 mg of the protein ligand per gram of the gold-sputtered membrane. The developed membranes were able to successfully capture and release the monoclonal antibody (mAb) Trastuzumab, as well as antibodies from fresh frozen human blood plasma in both static and dynamic setups. Therefore, they demonstrated successful functionalization and immobilization strategies. The antibody load was tested using bicinchoninic acid (BCA), ultraviolet-visible spectroscopy (UV-vis) measurements, and sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). The outcome is a fully functional affinity membrane that can be implemented in a variety of different antibody purification processes, eliminating the need for creating individualized strategies for modifying the surface to suit different substrates or conditions.

Development and material characteristics of glaucoma surgical implants

Background

Glaucoma is the leading cause of irreversible blindness worldwide. The reduction of intraocular pressure has proved to be the only factor which can be modified in the treatment, and surgical management is one of the important methods for the treatment of glaucoma patients.

Main text

In order to increase aqueous humor outflow and further reduce intraocular pressure, various drainage implants have been designed and applied in clinical practice. From initial Molteno, Baerveldt and Ahmed glaucoma implants to the Ahmed ClearPath device, Paul glaucoma implant, EX-PRESS and the eyeWatch implant, to iStent, Hydrus, XEN, PreserFlo, Cypass, SOLX Gold Shunt, etc., glaucoma surgical implants are currently undergoing a massive transformation on their structures and performances. Multitudinous materials have been used to produce these implants, from original silicone and porous polyethylene, to gelatin, stainless steel, SIBS, titanium, nitinol and even 24-carat gold. Moreover, the material geometry, size, rigidity, biocompatibility and mechanism (valved versus nonvalved) among these implants are markedly different. In this review, we discussed the development and material characteristics of both conventional glaucoma drainage devices and more recent implants, such as the eyeWatch and the new minimally invasive glaucoma surgery (MIGS) devices.

Conclusions

Although different in design and materials, these delicate glaucoma surgical implants have widely expanded the glaucoma surgical methods, and improved the success rate and safety of glaucoma surgery significantly. However, all of these glaucoma surgical implants have various limitations and should be used for different glaucoma patients at different conditions.

Recent Advances in Membranes Used for Nanofiltration to Remove Heavy Metals from Wastewater: A Review

The presence of heavy metal ions in polluted wastewater represents a serious threat to human health, making proper disposal extremely important. The utilization of nanofiltration (NF) membranes has emerged as one of the most effective methods of heavy metal ion removal from wastewater due to their efficient operation, adaptable design, and affordability. NF membranes created from advanced materials are becoming increasingly popular due to their ability to depollute wastewater in a variety of circumstances. Tailoring the NF membrane's properties to efficiently remove heavy metal ions from wastewater, interfacial polymerization, and grafting techniques, along with the addition of nano-fillers, have proven to be the most effective modification methods. This paper presents a review of the modification processes and NF membrane performances for the removal of heavy metals from wastewater, as well as the application of these membranes for heavy metal ion wastewater treatment. Very high treatment efficiencies, such as 99.90%, have been achieved using membranes composed of polyvinyl amine (PVAM) and glutaraldehyde (GA) for Cr³⁺ removal from wastewater. However, nanofiltration membranes have certain drawbacks, such as fouling of the NF membrane. Repeated cleaning of the membrane influences its lifetime.

A Janus Textile Capable of Radiative Subambient Cooling and Warming for Multi-Scenario Personal Thermal Management

Textiles with radiative cooling/warming capabilities provide a green and effective solution to personal thermal comfort in different climate scenarios. However, developing multiple-mode textiles for wearing in changing climates with large temperature variation remains a challenge. Here a Janus textile is reported, comprising a polyethersulfone (PES)-Al₂ O₃ cooling layer optically coupled with a Ti₃ C₂ T_x warming layer, which can realize sub-ambient radiative cooling, solar warming, and active Joule heating. Owing to the intrinsically high refractive index of PES and the rational design of the fiber topology, the nanocomposite PES textile features a record high solar reflectance of 0.97. Accompanied by an infrared (IR) emittance of 0.91 in the atmospheric window, sub-ambient cooling of 0.5-2.5 °C is achieved near noontime in humid summer under ≈1000 W m^-2 solar irradiation in Hong Kong. The simulated skin covered with the textile is ≈10 °C cooler than that with white cotton. The Ti₃ C₂ T_x layer provides a high solar-thermal efficiency of ≈80% and a Joule heating flux of 66 W m^-2 at 2 V and 15 °C due to its excellent spectral selectivity and electrical conductivity. The switchable multiple working modes enable effective and adaptive personal thermal management in changing environments.

Electrospun UV-cross-linked polyvinylpyrrolidone fibers modified with polycaprolactone/polyethersulfone microspheres for drug delivery

Electrospun fibers, often used as drug delivery systems, have two drawbacks - in the first stage of their action a sudden active substance burst release occurs and they have a relatively small capacity for a drug. In this work the fibers are modified by the addition of drug-loaded microspheres acting as micro-containers for the drug and increasing the total drug capacity of the system. Its release from such a structure is slowed down by placing the microspheres inside the fibers so they are covered with an outer layer of fiber-forming polymer. The work presents a new method (microsphere suspension electrospinning) of obtaining polyvinylpyrrolidone fibers cross-linked with UV light modified with polycaprolactone/polyethersulphone microspheres loaded with active substance - rhodamine 640 as a marker or ampicillin as a drug example. The influence of UV-cross-linking time and the microspheres addition on the degradation, mechanical strength and transport properties of fibrous mats was investigated. The mats were insoluble in water, in some cases mechanically stronger, their drug capacity was increased and the burst effect was eliminated. The antibacterial properties of ampicillin-loaded mats were confirmed. The product of proposed suspension electrospinning process has application potential as a drug delivery system.

Tackling Issues Observed during the Development of a Liquid Chromatography Method for Small Molecule Quantification in Antibody-Chelator Conjugate

In the context of targeted radionuclide therapy, antibody-chelator conjugates (ACCs) are an evolving class of antibody-related drugs with promising applications as tumor-targeted pharmaceuticals. Generally, a typical ACC consists of a recombinant monoclonal antibody (mAb) coupled to radionuclide via a chelating agent. Characterizing the ACC structure represents an analytical challenge since various impurities must be constantly monitored in the presence of formulation components during the quality control (QC) process. In this contribution, a reliable method devoted to the monitoring of an ACC sample, and its small molecule-related synthesis impurities, has been developed via liquid chromatography (LC). A problem-solving approach of common analytical issues was used to highlight some major issues encountered during method development. This included separation of poorly retained impurities (issue #1); interferences from the formulation components (issue #2); analysis of impurities in presence of ACC at high concentration (issue #3); and recovery of impurities during the whole analytical procedure (issue #4). To the best of our knowledge, this is the first time that a chromatographic method for the analysis of ACC synthesis impurities is presented. In addition, the developed approach has the potential to be more widely applied to the characterization of similar ACCs and other antibody-related drugs.

Crown ether-functionalized cellulose acetate membranes with potential applications in osseointegration

Due to its inherent properties and wide availability, cellulose acetate is an extremely competitive candidate for the production of polymeric membranes. However, for best results in particular applications, membrane modification is required in order to minimize unwanted interactions and introduce novel characteristics to the pristine polymer. In this study, the surface of commercial cellulose acetate membranes was functionalized with 4'-aminobenzo-15-crown-5 ether, using a covalent bonding approach. The main goal was the improvement of the membranes biomineralization ability, thus making them prospective materials for bone regeneration applications. The proposed reaction mechanism was confirmed by XPS and NMR analysis while the presence of the functionalization agents in the membranes structure was showed by ATR FT-IR and Raman spectra. The effects of the functionalization process on the morphology, thermal and mechanical properties of the membranes were studied by SEM, TGA and tensile tests. The obtained results revealed that the cellulose acetate membranes were successfully functionalized with crown ether and provided a good understanding of the interactions that took place between the polymer and the functionalization agents. Moreover, promising results were obtained during the Taguchi biomineralization studies. SEM images, EDX mapping and XRD spectra indicating that the CA-AB15C5 membranes have a superior Ca²⁺ ions retention ability, this causing an accentuated calcium phosphate deposition on the modified polymeric fibers, compared to the neat CA membrane.

A Review on Polyethersulfone Membranes in Polar Organic Chemical Integrative Samplers: Preparation, Characterization and Innovation

The membranes in polar organic chemical integrative samplers (POCIS) enclose the receiving sorbent and protect it from coming into direct contact with the environmental matrix. They have a crucial role in extending the kinetic regime of contaminant uptake, by slowing down their diffusion between the water phase and the receiving phase. The drive to improve passive sampling requires membranes with better design and enhanced performances. In this review, the preparation of standard polyethersulfone (PES) membranes for POCIS is presented, as well as methods to evaluate their composition, morphology, structure, and performance. Generally, only supplier-related morphological and structural data are provided, such as membrane type, thickness, surface area, and pore diameter. The issues related to the use of PES membranes in POCIS applications are exposed. Finally, alternative membranes to PES in POCIS are also discussed, although no better membrane has yet been developed. This review highlights the urge for more membrane characterization details and a better comprehension of the mechanisms which underlay their behavior and performance, to improve membrane selection and optimize passive sampler development.

Resin-Loaded Heterogeneous Polyether Sulfone Ion Exchange Membranes for Saline Groundwater Treatment

Arid areas often contain brackish groundwater that has a salinity exceeding 500 mg/L. This poses several challenges to the users of the water such as a salty taste and damage to household appliances. Desalination can be one of the key solutions to significantly lower the salinity and solute content of the water. However, the technology requires high energy inputs as well as managing waste products. This paper presents the fabrication of ultrafiltration heterogeneous ion exchange membranes for brackish groundwater treatment. Scanning electron microscopy (SEM) images showed a relatively uniform resin particle distribution within the polymer matrix. The mean roughness of the cation exchange membrane (CEM) and anion exchange membrane (AEM) surfaces increased from 42.12 to 317.25 and 68.56 to 295.95 nm, respectively, when resin loading was increased from 1 to 3.5 wt %. Contact angle measures suggested a more hydrophilic surface (86.13 to 76.26° and 88.10 to 74.47° for CEM and AEM, respectively) was achieved with greater resin loading rates. The ion exchange capacity (IEC) of the prepared membranes was assessed using synthetic groundwater in a dead-end filtration system and removal efficiency of K⁺, Mg²⁺, and Ca²⁺ were 56.0, 93.5, and 85.4%, respectively, for CEM with the highest resin loading. Additionally, the anion, NO₃⁻ and SO₄²⁻ removal efficiency was 84.2% and 52.4%, respectively, for the AEM with the highest resin loading. This work demonstrates that the prepared ultrafiltration heterogeneous ion exchange membranes have potential for selective removal for of ions by ion exchange, under filtration conditions at low pressure of 0.05 MPa.

Degradation of G-Type Nerve Agent Simulant with Phase-Inverted Spherical Polymeric-MOF Catalysts

For the neutralization of chemical warfare agents (CWAs), the generation of an effective catalyst that can be handled safely and applied in personal protective equipment is required. Recently, zirconium-based metal-organic frameworks (Zr-MOFs: UiO-66 and UiO-67) have shown great promise in the degradation of CWAs, including nerve agents. Their catalytic activity is owed to the interplay of both Zr(IV) Lewis acids and Lewis basic groups in the MOF structure. The latter act as proximal bases that can interact with CWAs and improve the catalytic activity of Zr-MOFs. The powder form of MOFs, though, makes them impractical catalysts, as it is challenging to handle, regenerate, and reuse them. To address this challenge, we have synthesized three Zr-MOFs with Lewis basic amino and pyridine functionalities and shaped them in spherical polymeric beads using the phase inversion method. Using this method, we can generate beads with many polymer and MOF combinations (MOF@polymer). We controlled the MOF loading in these beads, and scanning electron microscopy images revealed that the MOF crystals are evenly distributed in the polymeric matrix, ensuring effective catalytic activity. We used these beads to degrade dimethyl p-nitrophenyl phosphate (DMNP), a simulant for the G-type nerve agent. Using ³¹P NMR, we showed that UiO-66-NH₂@PES and UiO-67-(NH₂)₂@PES PES: poly(ether sulfone) beads destruct DMNP to dimethyl phosphate (DMP) with a half-life (t_1/2) of 5.09 and 4.34 min, respectively. Beads made of hydrophobic polymers such as poly(vinylidene fluoride) (PVDF), polystyrene (PS), and Zr-MOFs with pyridine functionalities show that the quantitative hydrolysis of DMNP requires more time compared to that seen with the UiO-66-NH₂@PES beads. Our work highlights the facile shaping of MOF powders into beads that can be easily regenerated with their catalytic activity to be maintained for at least three cycles of use.

Membrane surface roughness promotes rapid initial cell adhesion and long term microalgal biofilm stability

In biofilm membrane photobioreactors development, conscientious works revolving around the effect of external environment factors on microalgal biofilm growth were assessed but more comparative research about the role of carrier surfaces properties such as surface roughness is necessary. Thus, commercial polyethersulfone (PES) membranes with two different molecular-weight-cut-offs (1 kDa and 30 kDa) were selected as the main representatives of surface roughness in a 20 days long-term biofilm cultivation experiment under dynamic flow condition for the biofilm evolvement of three benthic diatoms (Amphora coffeaeformis, Cylindrotheca fusiformis and Navicula incerta). Results depicted that rougher 30 kDa PES enable higher cell attachment degree for C. fusiformis (25.85 ± 2.75 × 10⁹ cells m^-2), followed by A. coffeaeformis (11.86 ± 2.76 × 10⁹ cells m^-2) and N. incerta (10.10 ± 0.65 × 10⁹ cells m^-2). Bounded extracellular polymeric substances (bEPS) gathered were relatively higher than soluble EPS (sEPS) while bEPS accumulated at least 10% higher on smooth 1 kDa PES than rough 30 kDa PES for the purpose of enhancing the biofilm disruption resistivity under liquid flow. Moreover, cell adhesion mechanism was proposed via computational fluid dynamics in parallel with EPS analysis. Copious amount of asperities and stagnant zones present on rough 30 kDa surfaces accelerated biofilm development and the consistency of the results have a great valence for interpretation of microalgal biofilm lifestyle on porous surfaces.

Vacuum UV (VUV) Photo-Oxidation of Polyethersulfone (PES)

International need for water quality is placing a high demand on separation technology to develop advanced oxidative processes for polyethersulfone (PES) membranes to help improve water purification. Therefore, VUV photo-oxidation with a low pressure Ar plasma was studied to improve the hydrophilicity of PES by flowing oxygen over the surface during treatment. X-ray photoelectron spectroscopy (XPS) detected a decrease in the C at% (4.4 ± 1.7 at%), increase in O at% (3.7 ± 1.0 at%), and a constant S at% (5.4 ± 0.2 at%). Curve fitting of the XPS spectra showed a decrease in sp2 C-C aromatic group bonding, and an increase in C-O, C-S, O=C-OH, sulphonate (-SO3) and sulphate (-SO4) functional groups with treatment time. The water contact angle decreased from 71.9° for untreated PES down to a saturation level of 41.9° with treatment. Since scanning electron microscopy (SEM) showed no major changes in surface roughness, the increase in hydrophilicity was mainly due to oxidation of the surface. Washing the VUV photo-oxidized PES samples with water or ethanol increased the water contact angle saturation level up to 66° indicating the formation of a weak boundary layer.

A New Practice to Monitor the Fabrication Process of Fab-Targeting Ligands from Bevacizumab by LC-MS: Preparation and Analytical Characterization

The objective of this study was to qualitatively evaluate a Fab-targeting ligand preparation containing free thiol groups in the hinge region by using bevacizumab as a model. The evaluation focused on the purification of fragments through a nonaffinity-based process using a centrifugal ultrafiltration technique and mild reduction conditions for the intact production of F(ab’) fragments with specific inter-heavy-chain disulfide bonds cleavage. Under these conditions, F(ab’) fragments with a defined chemical composition were successfully obtained via proteolytic digestion followed by a controlled reduction reaction process maintaining the integrity of the binding sites. The ultrafiltration purification technique appears to be suitable for the removal of the digestive enzyme but inefficient for the removal of Fc fragments, thus requiring additional processing. A suitable analytical strategy was developed, allowing us to demonstrate the reformation of disulfide bridges between the two reduced cysteines within F(ab’) fragments.

Fouling Prevention in Polymeric Membranes by Radiation Induced Graft Copolymerization

The application of membrane processes in various fields has now undergone accelerated developments, despite the presence of some hurdles impacting the process efficiency. Fouling is arguably the main hindrance for a wider implementation of polymeric membranes, particularly in pressure-driven membrane processes, causing higher costs of energy, operation, and maintenance. Radiation induced graft copolymerization (RIGC) is a powerful versatile technique for covalently imparting selected chemical functionalities to membranes' surfaces, providing a potential solution to fouling problems. This article aims to systematically review the progress in modifications of polymeric membranes by RIGC of polar monomers onto membranes using various low- and high-energy radiation sources (UV, plasma, γ-rays, and electron beam) for fouling prevention. The feasibility of the modification method with respect to physico-chemical and antifouling properties of the membrane is discussed. Furthermore, the major challenges to the modified membranes in terms of sustainability are outlined and the future research directions are also highlighted. It is expected that this review would attract the attention of membrane developers, users, researchers, and scientists to appreciate the merits of using RIGC for modifying polymeric membranes to mitigate the fouling issue, increase membrane lifespan, and enhance the membrane system efficiency.

Condensation of pyrylium salts with mixed anhydrides: aryl ethers, aryl amines and sterically congested aromatics

Condensation of 2,4,6-triaryl pyrylium salts with mixed anhydrides, formed in situ from α-functionalized sodium acetates and an anhydride solvent, leads in good yields to the corresponding 2,4,6-triaryl benzenes functionalized at their 1-position.

Improvement of Properties and Performances of Polyethersulfone Ultrafiltration Membrane by Blending with Bio-Based Dragonbloodin Resin

Polyethersulfone (PES) is the most commonly used polymer for membrane ultrafiltration because of its superior properties. However, it is hydrophobic, as such susceptible to fouling and low permeation rate. This study proposes a novel bio-based additive of dragonbloodin resin (DBR) for improving the properties and performance of PES-based membranes. Four flat sheet membranes were prepared by varying the concentration of DBR (0-3%) in the dope solutions using the phase inversion method. After fabrication, the membranes were thoroughly characterized and were tested for filtration of humic acid solution to investigate the effect of DBR loading. Results showed that the hydrophilicity, porosity, and water uptake increased along with the DBR loadings. The presence of DBR in the dope solution fastened the phase inversion, leading to a more porous microstructure, resulted in membranes with higher number and larger pore sizes. Those properties led to more superior hydraulic performances. The PES membranes loaded with DBR reached a clean water flux of 246.79 L/(m2·h), 25-folds higher than the pristine PES membrane at a loading of 3%. The flux of humic acid solution reached 154.5 ± 6.6 L/(m2·h), 30-folds higher than the pristine PES membrane with a slight decrease in rejection (71% vs. 60%). Moreover, DBR loaded membranes (2% and 3%) showed an almost complete flux recovery ratio over five cleaning cycles, demonstrating their excellent antifouling property. The hydraulic performance could possibly be enhanced by leaching the entrapped DBR to create more voids and pores for water permeation.

Surface Design of Liquid Separation Membrane through Graft Polymerization: A State of the Art Review

Surface modification of membranes is an effective approach for imparting unique characteristics and additional functionalities to the membranes. Chemical grafting is a commonly used membrane modification technique due to its versatility in tailoring and optimizing the membrane surface with desired functionalities. Various types of polymers can be precisely grafted onto the membrane surface and the operating conditions of grafting can be tailored to further fine-tune the membrane surface properties. This review focuses on the recent strategies in improving the surface design of liquid separation membranes through grafting-from technique, also known as graft polymerization, to improve membrane performance in wastewater treatment and desalination applications. An overview on membrane technology processes such as pressure-driven and osmotically driven membrane processes are first briefly presented. Grafting-from surface chemical modification approaches including chemical initiated, plasma initiated and UV initiated approaches are discussed in terms of their features, advantages and limitations. The innovations in membrane surface modification techniques based on grafting-from techniques are comprehensively reviewed followed by some highlights on the current challenges in this field. It is concluded that grafting-from is a versatile and effective technique to introduce various functional groups to enhance the surface properties and separation performances of liquid separation membranes.

Anti-Foulant Ultrafiltration Polymer Composite Membranes Incorporated with Composite Activated Carbon/Chitosan and Activated Carbon/Thiolated Chitosan with Enhanced Hydrophilicity

A rapid increase in population worldwide is giving rise to the severe problem of safe drinking water availability, necessitating the search for solutions that are effective and economical. For this purpose, membrane technology has shown a lot of promise but faces the challenge of fouling, leading to a reduction in its lifetime. In this study, ultrafiltration polyethersulfone membranes were synthesized in two different concentrations, 16% wt. and 20% wt., using the phase inversion method. Chitosan and activated carbon were incorporated as individual fillers and then as composites in both the concentrations. A novel thiolated chitosan/activated carbon composite was introduced into a polyethersulfone membrane matrix. The membranes were then analyzed using Attenuated Total Reflection–Fourier-Transform Infrared spectroscopy(ATR-FTIR), Scanning Electron Microscopy (SEM), optical profilometry, gravimetric analysis, water retention, mechanical testing and contact angle. For membranes with the novel thiolated chitosan/activated carbon composite, Scanning Electron Microscopy micrographs showed better channels, indicating a better permeability possibility, reiterated by the flux rate results. The flux rate and bovine serum albumin flux were also assessed, and the results showed an increase from 105 L/m²h to 114 L/m²h for water flux and the antifouling determined by bovine serum albumin flux increased from 23 L/m²h to 51 L/m²h. The increase in values of water uptake from 22.84% to 76.5% and decrease in contact angle from 64.5 to 55.7 showed a significant increase in the hydrophilic character of the membrane.

Modification of Sulfonated Polyethersulfone Membrane as a Selective Adsorbent for Co(II) Ions

In the current study, a variety of sulfonated polyethersulfone (SPES)-based ion-exchange membranes were prepared and utilized as efficient and selective solid adsorbents for the detection of Co(II) ions in aquatic solutions. SPES membranes were treated with a variety of cations at a 2:1 ratio overnight. The produced materials were assessed via XRD, FT-IR, SEM, and TGA analyses. The structure of these materials was confirmed by FT-IR and XRD, which also confirmed the inclusion of Na⁺, NH₄⁺, and amberlite on the SPES surface successfully. TGA analysis showed that the thermal stabilities of these materials were enhanced, and the order of stability was NH₄-SPES > SPES > Na-SPES > A-SPES. Furthermore, the efficiency of these modified membranes for the determination and adsorption of a variety of metal ions was also examined by the ICP-OES analytical technique. A-SPES expressed a powerful efficiency of adsorption, and it showed an efficient as well as quantitative adsorption at pH = 6. Moreover, A-SPES displayed the highest adsorption capacity of 90.13 mg/g for Co(II) through the Langmuir adsorption isotherm.

Engineered Bioactive Polymeric Surfaces by Radiation Induced Graft Copolymerization: Strategies and Applications

The interest in developing antimicrobial surfaces is currently surging with the rise in global infectious disease events. Radiation-induced graft copolymerization (RIGC) is a powerful technique enabling permanent tunable and desired surface modifications imparting antimicrobial properties to polymer substrates to prevent disease transmission and provide safer biomaterials and healthcare products. This review aims to provide a broader perspective of the progress taking place in strategies for designing various antimicrobial polymeric surfaces using RIGC methods and their applications in medical devices, healthcare, textile, tissue engineering and food packing. Particularly, the use of UV, plasma, electron beam (EB) and γ-rays for biocides covalent immobilization to various polymers surfaces including nonwoven fabrics, films, nanofibers, nanocomposites, catheters, sutures, wound dressing patches and contact lenses is reviewed. The different strategies to enhance the grafted antimicrobial properties are discussed with an emphasis on the emerging approach of in-situ formation of metal nanoparticles (NPs) in radiation grafted substrates. The current applications of the polymers with antimicrobial surfaces are discussed together with their future research directions. It is expected that this review would attract attention of researchers and scientists to realize the merits of RIGC in developing timely, necessary antimicrobial materials to mitigate the fast-growing microbial activities and promote hygienic lifestyles.

Influence of monomers involved in the fabrication of a novel PES based nanofiltration thin-film composite membrane and its performance in the treatment of common effluent (CETP) textile industrial wastewater

OBJECTIVE

In this article, monomers (tannic acid (TA) and m- phenylenediamine (MPD)) were used in the fabrication of a novel PES based thin-film composite nanofiltration (TFC-NF) membrane for the treatment of a common effluent treatment plant (CETP) of textile industrial wastewater.

MEMBRANE SYNTHESIS

PES support sheets and TFC layers were fabricated via non-solvent induced phase inversion and in-situ interfacial polymerization (IP) process. The ultra-thin active layer was synthesized via the IP process with monomers such as tannic acid (TA) and m- phenylenediamine (MPD). T and M series membranes correspond to (PES/x wt% TA, x = 2, 4, 6) as T1, T2, T3 -TA and (PES/x wt% MPD, x = 2, 4, 6) as M1, M2, M3-MPD respectively. M0 corresponds to PES which is the virgin membrane.

RESULTS

The chemical structure, surface morphology, surface roughness and surface properties were explored using fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and contact angle, respectively. The filtration performance of the thin-film composite nanofiltration (TFC-NF) membranes was investigated by various properties like pure water flux, salt rejection, porosity, mean pore radius and antifouling analysis.

CONCLUSION

T1-TA membrane showed better water permeability, high salt rejection and better industrial effluent rejection with 94.4% of TDS that are suitable for industrial reuse and agricultural irrigation. Moreover, for T1-TA membrane, the water flux, porosity, mean pore radius, salt rejection, surface roughness and contact angle of 43.5lm^- 2 h ^- 1, 47.1%, 16.7nm, 72.7%, 11.7nm and 41.48°was achieved respectively that was found to be higher than that of all the other fabricated membranes. Further, the rejection efficiency rate of textile effluent characteristics such as pH, turbidity, TDS, alkalinity, total hardness, BOD and COD were also achieved with maximum deduction in the T1-TA TFC-NF membrane compared to the M0-Virgin PES membrane. From the results, it can be confirmed that the T1-TA membrane significantly reduced the alkalinity, total hardness, BOD and COD rejections of 78%, 77.3%, 58.5% and 67.5% respectively, present in the effluent. Water flux recovery ratio (FRR) was improved from 74.6% for M0-Virgin PES membrane to 94.8% for T1-TA membrane. The modified TFC-NF membranes especially T1-TA, had better anti-fouling property and excellent hydrophilicity than the unmodified M0-Virgin PES membrane.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s40201-021-00624-x.

Selective Oxidation of Polysulfide Latexes to Produce Polysulfoxide and Polysulfone in a Waterborne Environment

Polymers containing sulfur centers with high oxidation states in the main chain, polysulfoxide and polysulfone, display desirable properties such as thermomechanical and chemical stability. To circumvent their challenging direct synthesis, methods based on the oxidation of a parent polysulfide have been developed but are plagued by uncontrolled reactions, leading either to ill-defined mixtures of polysulfoxides and polysulfones or to polysulfones with reduced degrees of polymerization due to overoxidation of the polymer. We developed an alternative method to produce well-defined polysulfoxide and polysulfone in a waterborne colloidal emulsion using different oxidants to control the oxidation state of sulfur in the final materials. The direct oxidation of water-based polysulfide latexes avoided the use of volatile organic solvents and allowed for the control of the oxidation state of the sulfur atoms. Oxidation of parent polysulfides by tert-butyl hydroperoxide led to the production of pure polysulfoxides, even after 70 days of reaction time. Additionally, hydrogen peroxide produced both species through the course of the reaction but yielded fully converted polysulfones after 24 h. By employing mild oxidants, our approach controlled the oxidation state of the sulfur atoms in the final sulfur-containing polymer and prevented any overoxidation, thus ensuring the integrity of the polymer chains and colloidal stability of the system. We also verified the selectivity, versatility, and robustness of the method by applying it to polysulfides of different chemical compositions and structures. The universality demonstrated by this method makes it a powerful yet simple platform for the design of sulfur-containing polymers and nanoparticles.

Persulfate-activated charcoal mixture: an efficient oxidant for the synthesis of sulfonated benzo[d][1,3]oxazines from N-(2-vinylphenyl)amides and thiols in aqueous solution

A series of 2,4-aryl-4-((arylsulfonyl)methyl)-4H-benzo[d][1,3]oxazines in good to excellent yields have directly been obtained from N-(2-vinylphenyl)amides and thiols by employing a mixture of K₂S₂O₈-activated charcoal in aqueous acetonitrile solution at 50 °C. A plausible mechanism for the reaction is reported. It reveals that the reaction follows a radical pathway and the persulfate has been the oxygen source for formation of the sulfone group in the products. It is worth mentioning that this protocol utilizes an easily accessible K₂S₂O₈-activated charcoal mixture and thiols, respectively, as an oxidant and sulfonylating precursors for the first time.

Infusion of Silver-Polydopamine Particles into Polyethersulfone Matrix to Improve the Membrane's Dye Desalination Performance and Antibacterial Property

The advancement in membrane science and technology, particularly in nanofiltration applications, involves the blending of functional nanocomposites into the membranes to improve the membrane property. In this study, Ag-polydopamine (Ag-PDA) particles were synthesized through in situ PDA-mediated reduction of AgNO₃ to silver. Infusing Ag-PDA particles into polyethersulfone (PES) matrix affects the membrane property and performance. X-ray photoelectron spectroscopy (XPS) analyses confirmed the presence of Ag-PDA particles on the membrane surface. Field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM) describe the morphology of the membranes. At an optimum concentration of Ag-PDA particles (0.3 wt % based on the concentration of PES), the modified membrane exhibited high water flux 13.33 L∙m⁻²∙h⁻¹ at 4 bar with high rejection for various dyes of >99%. The PES_Ag-PDA0.3 membrane had a pure water flux more than 5.4 times higher than that of a pristine membrane. Furthermore, in bacterial attachment using Escherichia coli, the modified membrane displayed less bacterial attachment compared with the pristine membrane. Therefore, immobilizing Ag-PDA particles into the PES matrix enhanced the membrane performance and antibacterial property.

CO2 gas separation using mixed matrix membranes based on polyethersulfone/MIL-100(Al)

The excessive use of natural gas and other fossil fuels by the industrial sector leads to the production of great quantities of gas pollutants, including CO2, SO2, and NO x . Consequently, these gases increase the temperature of the earth, producing global warming. Different strategies have been developed to help overcome this problem, including the utilization of separation membrane technology. Mixed matrix membranes (MMMs) are hybrid membranes that combine an organic polymer as a matrix and an inorganic compound as a filler. In this study, MMMs were prepared based on polyethersulfone (PES) and a type of metal–organic framework (MOF), Materials of Institute Lavoisier (MIL)-100(Al) [Al3O(H2O)2(OH)(BTC)2] (BTC: benzene 1,3,5-tricarboxylate) using a phase inversion method. The influence on the properties of the produced membranes by addition of 5, 10, 20, and 30% MIL-100(Al) (w/w) to the PES was also investigated. Fourier-transform infrared spectroscopy (FTIR) analysis indicated that no chemical interactions occurred between PES and MIL-100(Al). Scanning electron microscope (SEM) images showed agglomeration at PES/MIL-100(Al) 30% (w/w) and that the thickness of the dense layer increased up to 3.70 µm. After the addition of MIL-100(Al) of 30% (w/w), the permeability of the MMMs for CO2, O2, and N2 gases was enhanced by approximately 16, 26, and 14 times, respectively, as compared with a neat PES membrane. The addition of MIL-100(Al) to PES increased the thermal stability of the membranes, reaching 40°C as indicated by thermogravimetry analysis (TGA). An addition of 20% MIL-100(Al) (w/w) increased membrane selectivity for CO2/O2 from 2.67 to 4.49 (approximately 68.5%), and the addition of 10% MIL-100(Al) increased membrane selectivity for CO2/N2 from 1.01 to 2.12 (approximately 110.1%).

Limitations of Integrative Passive Samplers as a Tool for the Quantification of Pharmaceuticals in the Environment - A Critical Review with the Latest Innovations

This review starts with a presentation of the theory of kinetic uptake by passive sampling (PS), which is traditionally used to distinguish between integrative and equilibrium samplers. Demonstrated limitations of this model for the passive sampling of pharmaceuticals from water were presented. Most notably, the contribution of the protective membrane in the resistance to mass transfer of lipophilic analytes and the well documented effect of external parameters on sampling rates contributed to the greatest uncertainty in PS application. The diffusion gradient in thin layer (DGT) technique seems to reduce the effect of external parameters (e.g., flow rate) to some degree. The laboratory-determined integrative uptake periods over defined sampler deployments was compared, and the discrepancy found suggests that the most popular Polar Organic Chemical Integrative Sampler (POCIS) could in some cases utilized as an equilibrium sampler. This assertion is supported by own calculations for three pharmaceuticals with extremely different lipophilic characters. Finally, the reasons performance reference compounds (PRCs) are not recommended for the reduction in uncertainty of the TWAC found by adsorptive samplers were presented. It was concluded that techniques of passive sampling of pharmaceuticals need a new uptake model to fit the current situation.

Understanding Loss of Soluble High Molecular Weight Species during Filtration of Low Concentration Therapeutic Monoclonal Antibodies

Sterile filtration is an integral step in the manufacturing process of biological therapeutics. Protein adsorption to the surface of the filter is an unfortunate, common occurrence that can result in manufacturing difficulties, such as filter fouling or product loss. Although many filters have surface modifications to minimize adsorption, under certain conditions binding can still occur. We observed the loss of high molecular weight species (HMWS) during sterile filtration of eight different therapeutic monoclonal antibodies formulated at low protein concentrations across a commonly used hydrophilic polyvinylidene fluoride or polyvinylidene difluoride (PVDF) filter membrane. The protein absorption was specific to HMWS, and each antibody exhibited different degrees of filter adsorption. Debye screening length parameters of the solution (e.g. ionic strength) were adjusted, and influenced the amount of HMWS lost during filtration. Additionally, HMWS of a representative antibody (mAb1) were observed to be more positively charged than other size variants by ion-exchange chromatography. From these results, it is concluded that this HMWS loss is due to electrostatic interactions between HMWS and the filter surface. This adsorption can be reduced by increasing the ionic strength of the buffer matrix, demonstrating the influence of the Debye screening length in the filtration of low concentration proteins.

Recent Advances in the Rejection of Endocrine-Disrupting Compounds from Water Using Membrane and Membrane Bioreactor Technologies: A Review

Water is a critical resource necessary for life to be sustained, and its availability should be secured, appropriated, and easily obtainable. The continual detection of endocrine-disrupting chemicals (EDCs) (ng/L or µg/L) in water and wastewater has attracted critical concerns among the regulatory authorities and general public, due to its associated public health, ecological risks, and a threat to global water quality. Presently, there is a lack of stringent discharge standards regulating the emerging multiclass contaminants to obviate its possible undesirable impacts. The conventional treatment processes have reportedly ineffectual in eliminating the persistent EDCs pollutants, necessitating the researchers to develop alternative treatment methods. Occurrences of the EDCs and the attributed effects on humans and the environment are adequately reviewed. It indicated that comprehensive information on the recent advances in the rejection of EDCs via a novel membrane and membrane bioreactor (MBR) treatment techniques are still lacking. This paper critically studies and reports on recent advances in the membrane and MBR treatment methods for removing EDCs, fouling challenges, and its mitigation strategies. The removal mechanisms and the operating factors influencing the EDCs remediation were also examined. Membranes and MBR approaches have proven successful and viable to eliminate various EDCs contaminants.

Preparation of a PES/PFSA-g-MWCNT ultrafiltration membrane with improved permeation and antifouling properties

In this study, perfluorosulfonic acid (PFSA) was firstly grafted on multi-walled carbon nanotubes (MWCNTs) to obtain PFSA-g-MWCNT nanocomposites.

The impact of relative humidity on electrospun polymer fibers: From structural changes to fiber morphology

Electrospinning is one of the most important methods used for the production of nanostructured materials. Electrospun nanofibers are used in a wide spectrum of applications such as drug delivery systems, filtration, fog harvesting, tissue engineering, smart textiles, flexible electronics, and more. Control of the manufacturing process is essential for further technology developments. In electrospinning, relative humidity is a crucial parameter that influences nearly all the properties of the collected fibers, such as morphology, mechanical properties, liquid retention, wetting properties, phase composition, chain conformation, and surface potential. Relative humidity is a determining component of a reliable process as it governs charge dissipation and solvent evaporation. This review summarizes the electrospinning process and its applications, phase separation processes, and impact of relative humidity on the properties of polymer fibers. We investigated relative humidity effects on both hydrophilic and hydrophobic polymers using over 20 polymers and hundreds of solvent systems. Most importantly, we underlined the indisputable importance of relative humidity in process repeatability and demonstrated its impact on almost all aspects of fiber production from a solution droplet to an electrospun network.