Optical dosimetry of radiotherapy beams using Cherenkov radiation: the relationship between light emission and dose

Preliminary study of luminescence phenomena from various materials under ultra-high dose rate proton beam irradiation for dose management

This research aimed to identify materials capable of emitting visible light useful for dose management at ultra-high dose rate (uHDR). Various materials were irradiated with proton beams at a normal dose rate (NDR) and uHDR, and the resulting surface luminescence was captured using a high-sensitivity camera. The luminescence images were compared with the corresponding dose distributions. The luminescence of Tough Water Phantoms (Kyoto Kagaku Co. Ltd.) with various thicknesses was also observed to evaluate the depth distributions. Dose distributions were measured using two-dimensional ionization chamber detector arrays. The Tough Bone Phantom (Kyoto Kagaku Co. Ltd.) exhibited the strongest luminescence among the materials, followed by the Tough Water Phantom. The metals exhibited relatively weak luminescence. The luminescence profiles of the Tough Water Phantom, water, the Tough Lung Phantom (Kyoto Kagaku Co. Ltd.), and an acrylic were similar to the dose profiles. The luminescence distribution of the Tough Water Phantom in the depth direction was similar to that of the dose distributions. The luminescence at uHDR and NDR were approximately equivalent. The Tough Water Phantom was found to be a suitable material for dosimetry, even at uHDR. More detailed measurement data, such as wavelength data, must be collected to elucidate the luminescence mechanism.

4Din vivodosimetry for a FLASH electron beam using radiation-induced acoustic imaging

Objective. The primary goal of this research is to demonstrate the feasibility of radiation-induced acoustic imaging (RAI) as a volumetric dosimetry tool for ultra-high dose rate FLASH electron radiotherapy (FLASH-RT) in real time. This technology aims to improve patient outcomes by accurate measurements ofin vivodose delivery to target tumor volumes.Approach. The study utilized the FLASH-capable eRT6 LINAC to deliver electron beams under various doses (1.2 Gy pulse-1to 4.95 Gy pulse-1) and instantaneous dose rates (1.55 × 105Gy s-1to 2.75 × 106Gy s-1), for imaging the beam in water and in a rabbit cadaver with RAI. A custom 256-element matrix ultrasound array was employed for real-time, volumetric (4D) imaging of individual pulses. This allowed for the exploration of dose linearity by varying the dose per pulse and analyzing the results through signal processing and image reconstruction in RAI.Main Results. By varying the dose per pulse through changes in source-to-surface distance, a direct correlation was established between the peak-to-peak amplitudes of pressure waves captured by the RAI system and the radiochromic film dose measurements. This correlation demonstrated dose rate linearity, including in the FLASH regime, without any saturation even at an instantaneous dose rate up to 2.75 × 106Gy s-1. Further, the use of the 2D matrix array enabled 4D tracking of FLASH electron beam dose distributions on animal tissue for the first time.Significance. This research successfully shows that 4Din vivodosimetry is feasible during FLASH-RT using a RAI system. It allows for precise spatial (∼mm) and temporal (25 frames s-1) monitoring of individual FLASH beamlets during delivery. This advancement is crucial for the clinical translation of FLASH-RT as enhancing the accuracy of dose delivery to the target volume the safety and efficacy of radiotherapeutic procedures will be improved.

Investigation of Photodynamic Therapy Promoted by Cherenkov Light Activated Photosensitizers-New Aspects and Revelations

This work investigates the proposed enhanced efficacy of photodynamic therapy (PDT) by activating photosensitizers (PSs) with Cherenkov light (CL). The approaches of Yoon et al. to test the effect of CL with external radiation were taken up and refined. The results were used to transfer the applied scheme from external radiation therapy to radionuclide therapy in nuclear medicine. Here, the CL for the activation of the PSs (psoralen and trioxsalen) is generated by the ionizing radiation from rhenium-188 (a high-energy beta-emitter, Re-188). In vitro cell survival studies were performed on FaDu, B16 and 4T1 cells. A characterization of the PSs (absorbance measurement and gel electrophoresis) and the CL produced by Re-188 (luminescence measurement) was performed as well as a comparison of clonogenic assays with and without PSs. The methods of Yoon et al. were reproduced with a beam line at our facility to validate their results. In our studies with different concentrations of PS and considering the negative controls without PS, the statements of Yoon et al. regarding the positive effect of CL could not be confirmed. There are slight differences in survival fractions, but they are not significant when considering the differences in the controls. Gel electrophoresis showed a dominance of trioxsalen over psoralen in conclusion of single and double strand breaks in plasmid DNA, suggesting a superiority of trioxsalen as a PS (when irradiated with UVA). In addition, absorption measurements showed that these PSs do not need to be shielded from ambient light during the experiment. An observational test setup for a PDT nuclear medicine approach was found. The CL spectrum of Re-188 was measured. Fluctuating inconclusive results from clonogenic assays were found.

Imaging and characterization of optical emission fromex vivotissue during conventional and UHDR PBS proton therapy

Objective. Imaging of optical photons emitted from tissue during radiotherapy is a promising technique for real-time visualization of treatment delivery, offering applications in dose verification, treatment monitoring, and retrospective treatment plan comparison. This research aims to explore the feasibility of intensified imaging of tissue luminescence during proton therapy (PT), under both conventional and ultra-high dose rate (UHDR) conditions.Approach. Conventional and UHDR pencil beam scanning (PBS) PT irradiation of freshex vivoporcine tissue and tissue-mimicking plastic phantom was imaged using intensified complementary metal-oxide-semiconductor(CMOS) cameras. The optical emission from tissue was characterized during conventional irradiation using both blue and red-sensitive intensifiers to ensure adequate spectral coverage. Spectral characterization was performed using bandpass filters between the lens and sensor. Imaging of conventional proton fields (240 MeV, 10 nA) was performed at 100 Hz frame rate, while UHDR PBS proton delivery (250 MeV, 99 nA) was recorded at 1 kHz frame rate. Dependence of optical emission yield on proton energy was studied using an optical tissue-mimicking plastic phantom and a range shifter. Finally, we demonstrated fast beam tracking capability of fast camera towardsin vivomonitoring of FLASH PT.Main results. Under conventional treatment dose rates optical emission was imaged with single spot resolution. Spot profiles were found to agree with the treatment planning system calculation within >90% for all spectral bands and spot intensity was found to vary with spectral filtration. The resultant polychromatic emission presented a maximum intensity at 650 nm and decreasing signal at lower wavelengths, which is consistent with expected attenuation patterns of high fat and muscle tissue. For UHDR beam imaging, optical yield increased with higher proton energy. Imaging at 1 kHz allowed continuous monitoring of delivery during porcine tissue irradiation, with clear identification of individual dwell positions. The number of dwell positions matched the treatment plan in total and per row showing adequate temporal capability of iCMOS imaging.Significance. For the first time, this study characterizes optical emission from tissue during PT and demonstrates our capability of fast optical tracking of pencil proton beam on the tissue anatomy in both conventional and UHDR setting. Similar to the Cherenkov imaging in radiotherapy, this imaging modality could enable a seamless, independent validation of PT treatments.

Characterization of Cherenkov imaging parameters and positional constraints on an O-ring linear accelerator

Objective. With the introduction of Cherenkov imaging technology on the Halcyon O-ring linear accelerator platform, we seek to demonstrate the imaging feasibility and optimize camera placement.Approach. Imaging parameters were probed by acquiring triggering data Cherenkov image frames for simplistic beams on the Halcyon and comparing the analyzed metrics with those from the TrueBeam platform. Camera position was analyzed by performing 3D rendering of patient treatment plans for various sites and iterating over camera positions to assess treatment area visibility.Main results. Commercial Cherenkov imaging systems are compatible with the pulse timing of the Halcyon, and this platform design favorably impacts signal to noise in Cherenkov image frames. Additionally, ideal camera placement is treatment site dependent and is always within a biconical zone of visibility centered on the isocenter. Visibility data is provided for four treatment sites, with suggestions for camera placement based on room dimensions. Median visibility values were highest for right breast plans, with values of 80.33% and 68.49% for the front and rear views respectively. Head and neck plans presented with the lowest values at 26.44% and 38.18% respectively.Significance. This work presents the first formal camera positional analysis for Cherenkov imaging on any platform and serves as a template for performing similar work for other irradiation platforms. Additionally, this study confirms the Cherenkov imaging parameters do not need to be changed for optimal imaging on the Halcyon. Lastly, the presented methodology provides a framework which could be further expanded to other optical imaging systems which rely on line of sight visibility to the patient.

A simulation study of in-beam visualization system for proton therapy by monitoring scattered protons

Recently, in-beam positron emission tomography (PET) has been actively researched for reducing biological washout effects and dose monitoring during irradiation. However, the positron distribution does not precisely reflect the dose distribution since positron production and ionization are completely different physical processes. Thus, a novel in-beam system was proposed to determine proton dose range by measuring scattered protons with dozens of scintillation detectors surrounding the body surface. While previous studies conducted a preliminary experiment with a simple phantom, we simulated more complex situations in this paper. Especially, we conducted three stepwise simulation studies to demonstrate the feasibility of the proposed method. First, a simple rectangular phantom was reproduced on simulation and irradiated with protons for obtaining current values and Monte Carlo (MC) dose. Next, we trained a deep learning model to estimate 2-dimensional-dose range (2D-DL dose) from measured current values for simulation (A). We simulated plastic scintillators as detectors to measure the scattered protons. Second, a rectangular phantom with an air layer was used, and 3D-DL dose was estimated in simulation (B). Finally, a cylindrical phantom that mimics the human body was used for confirming the estimation quality of the simulation (C). Consequently, the position of the Bragg peak was estimated with an error of 1.0 mm in simulation (A). In addition, the position of the air layer, as well as the verifying peak position with an error of 2.1 mm, was successfully estimated in simulation (B). Although the estimation error of the peak position was 12.6 mm in simulation (C), the quality was successfully further improved to 9.3 mm by incorporating the mass density distribution obtained from the computed tomography (CT). These simulation results demonstrated the potential of the as-proposed verification system. Additionally, the effectiveness of CT utilization for estimating the DL dose was also indicated.

Low energy X-ray dosimeter based on LYSO:Ce fluorescent powder

Cerium-doped lutetium yttrium orthosilicate (LYSO:Ce) powder has been synthesized by the co-precipitation method. The influence of the Ce3+ doping concentration on the lattice structure and luminescence characteristics of LYSO:Ce powder was investigated by X-ray diffraction (XRD) and photoluminescence (PL). The XRD measurement indicates that the lattice structure of LYSO:Ce powder was not changed by doping ions. PL results show that LYSO:Ce powder has better luminescence performance when the Ce doping concentration is 0.3 mol%. In addition, the fluorescence lifetime of the samples was measured, and the results show that LYSO:Ce has a short decay time. The radiation dosimeter was prepared by LYSO:Ce powder with a Ce doping concentration of 0.3 mol%. Radioluminescence properties of the radiation dosimeter also were studied under X-ray irradiation at doses from 0.03 to 0.76 Gy, with dose rate from 0.09 to 2.284 Gy/min. The results show that the dosimeter has a certain linear relationship response and stability. The radiation responses of the dosimeter at different energies were obtained under X-ray irradiation with X-ray tube voltages ranging from 20 to 80 kV. The results show that the dosimeter has a certain linear relationship response in the low energy range of radiotherapy. These results indicate the potential application of LYSO:Ce powder dosimeters in remote radiotherapy and online radiation monitoring.

Color-resolved Cherenkov imaging allows for differential signal detection in blood and melanin content

Significance

High-energy x-ray delivery from a linear accelerator results in the production of spectrally continuous broadband Cherenkov light inside tissue. In the absence of attenuation, there is a linear relationship between Cherenkov emission and deposited dose; however, scattering and absorption result in the distortion of this linear relationship. As Cherenkov emission exits the absorption by tissue dominates the observed Cherenkov emission spectrum. Spectroscopic interpretation of this effects may help to better relate Cherenkov emission to ionizing radiation dose delivered during radiotherapy.

Aim

In this study, we examined how color Cherenkov imaging intensity variations are caused by absorption from both melanin and hemoglobin level variations, so that future Cherenkov emission imaging might be corrected for linearity to delivered dose.

Approach

A custom, time-gated, three-channel intensified camera was used to image the red, green, and blue wavelengths of Cherenkov emission from tissue phantoms with synthetic melanin layers and varying blood concentrations. Our hypothesis was that spectroscopic separation of Cherenkov emission would allow for the identification of attenuated signals that varied in response to changes in blood content versus melanin content, because of their different characteristic absorption spectra.

Results

Cherenkov emission scaled with dose linearly in all channels. Absorption in the blue and green channels increased with increasing oxy-hemoglobin in the blood to a greater extent than in the red channel. Melanin was found to absorb with only slight differences between all channels. These spectral differences can be used to derive dose from measured Cherenkov emission.

Conclusions

Color Cherenkov emission imaging may be used to improve the optical measurement and determination of dose delivered in tissues. Calibration for these factors to minimize the influence of the tissue types and skin tones may be possible using color camera system information based upon the linearity of the observed signals.

Detection of Shortwave-Infrared Cerenkov Luminescence from Medical Isotopes

Medical radioisotopes produce Cerenkov luminescence (CL) from charged subatomic particles (β+/-) traveling faster than light in dielectric media (e.g., tissue). CL is a blue-weighted and continuous emission, decreasing proportionally to increasing wavelength. CL imaging (CLI) provides an economic PET alternative with the advantage of also being able to image β- and α emitters. Like any optical modality, CLI is limited by the optical properties of tissue (scattering, absorption, and ambient photon removal). Shortwave-infrared (SWIR, 900-1700 nm) CL has been detected from MeV linear accelerators but not yet from keV medical radioisotopes. Methods: Indium-gallium-arsenide sensors and SWIR lenses were mounted onto an ambient light-excluding preclinical enclosure. An exposure and processing pipeline was developed for SWIR CLI and then performed across 6 radioisotopes at in vitro and in vivo conditions. Results: SWIR CL was detected from the clinical radioisotopes 90Y, 68Ga, 18F, 89Zr, 131I, and 32P (biomedical research). SWIR CLI's advantage over visible-wavelength (VIS) CLI (400-900 nm) was shown via increased light penetration and decreased scattering at depth. The SWIR CLI radioisotope sensitivity limit (8.51 kBq/μL for 68Ga), emission spectrum, and ex vivo and in vivo examples are reported. Conclusion: This work shows that radioisotope SWIR CLI can be performed with unmodified commercially available components. SWIR CLI has significant advantages over VIS CLI, with preserved VIS CLI features such as radioisotope radiance levels and dose response linearity. Further improvements in SWIR optics and technology are required to enable widespread adoption.

One Year of Clinic-Wide Cherenkov Imaging for Discovery of Quality Improvement Opportunities in Radiation Therapy

PURPOSE

Cherenkov imaging is clinically available as a radiation therapy treatment verification tool. The aim of this work was to discover the benefits of always-on Cherenkov imaging as a novel incident detection and quality improvement system through review of all imaging at our center.

METHODS AND MATERIALS

Multicamera Cherenkov imaging systems were permanently installed in 3 treatment bunkers, imaging continuously over a year. Images were acquired as part of normal treatment procedures and reviewed for potential treatment delivery anomalies.

RESULTS

In total, 622 unique patients were evaluated for this study. We identified 9 patients with treatment anomalies occurring over their course of treatment, which were only detected with Cherenkov imaging. Categorizing each event indicated issues arising in simulation, planning, pretreatment review, and treatment delivery, and none of the incidents were detected before this review by conventional measures. The incidents identified in this study included dose to unintended areas in planning, dose to unintended areas due to positioning at treatment, and nonideal bolus placement during setup.

CONCLUSIONS

Cherenkov imaging was shown to provide a unique method of detecting radiation therapy incidents that would have otherwise gone undetected. Although none of the events detected in this study reached the threshold of reporting, they identified opportunities for practice improvement and demonstrated added value of Cherenkov imaging in quality assurance programs.

Comparison of surface dose during whole breast radiation therapy on Halcyon and TrueBeam using Cherenkov imaging

The emergence of the Halcyon linear accelerator has allowed for increased patient throughput and improved treatment times for common treatment sites in radiation oncology. However, it has been shown that this can lead to increased surface dose in sites like breast cancer compared with treatments on conventional machines with flattened radiation beams. Cherenkov imaging can be used to estimate surface dose by detection of Cherenkov photons emitted in proportion to energy deposition from high energy electrons in tissue. Phantom studies were performed with both square beams in reference conditions and with clinical treatments, and dosimeter readings and Cherenkov images report higher surface dose (25% for flat phantom entrance dose, 5.9% for breast phantom treatment) from Halcyon beam deliveries than for equivalent deliveries from a TrueBeam linac. Additionally, the first Cherenkov images of a patient treated with Halcyon were acquired, and superficial dose was estimated.

Performance comparison of quantitative metrics for analysis of in vivo Cherenkov imaging incident detection during radiotherapy

OBJECTIVES

Examine the responses of multiple image similarity metrics to detect patient positioning errors in radiotherapy observed through Cherenkov imaging, which may be used to optimize automated incident detection.

METHODS

An anthropomorphic phantom mimicking patient vasculature, a biological marker seen in Cherenkov images, was simulated for a breast radiotherapy treatment. The phantom was systematically shifted in each translational direction, and Cherenkov images were captured during treatment delivery at each step. The responses of mutual information (MI) and the γ passing rate (%GP) were compared to that of existing field-shape matching image metrics, the Dice coefficient, and mean distance to conformity (MDC). Patient images containing other incidents were analyzed to verify the best detection algorithm for different incident types.

RESULTS

Positional shifts in all directions were registered by both MI and %GP, degrading monotonically as the shifts increased. Shifts in intensity, which may result from erythema or bolus-tissue air gaps, were detected most by %GP. However, neither metric detected beam-shape misalignment, such as that caused by dose to unintended areas, as well as currently employed metrics (Dice and MDC).

CONCLUSIONS

This study indicates that different radiotherapy incidents may be detected by comparing both inter- and intrafractional Cherenkov images with a corresponding image similarity metric, varying with the type of incident. Future work will involve determining appropriate thresholds per metric for automatic flagging.

ADVANCES IN KNOWLEDGE

Classifying different algorithms for the detection of various radiotherapy incidents allows for the development of an automatic flagging system, eliminating the burden of manual review of Cherenkov images.

Correcting angular dependencies using non-polarized components of Cherenkov light in water during high-energy X-ray irradiation

OBJECTIVE

Dose distribution measurements of high-energy X-rays from medical linear accelerators (LINAC) in water are important for quality control (QC) of the system. Although Cherenkov-light imaging is a useful method for measuring the high-energy X-ray dose distribution, depth profiles have an underestimated dose at increased depths due to the angular dependency of the Cherenkov light generated in water. In this study, we use a linear polarizer to separate the majority of polarized components from the majority of unpolarized components of Cherenkov-light images in water and then use this information to correct for angular dependencies.

METHODS

A water phantom, a cooled charge-coupled device (CCD) camera, and a polarizer were installed in a black box. Then, the water phantom was irradiated from the upper side with 6 MV or 10 MV X-rays, and the Cherenkov light generated in water was imaged with the polarizer axis at both parallel and perpendicular orientations to the beam. By using these images from the two orientations relative to the beam, we corrected the angular dependency of the Cherenkov light.

RESULTS

By subtracting the images measured with the polarizer perpendicular to the beams from the images measured with the polarizer parallel to the beams, we could obtain images with only the polarized components. Using these images, we could calculate the images with non-polarized components that had similar depth profiles to those calculated with a planning system. The average difference between corrected depth profiles and those calculated with the planning system was less than 1%, while that between uncorrected depth profiles and the planning system was more than 8.3% in depths of water from 20 mm to 100 mm.

CONCLUSION

We conclude that use of the polarizer has the potential to improve the accuracy of dose distribution in Cherenkov-light imaging of water using high-energy X-rays. This article is protected by copyright. All rights reserved.

Cherenkov Luminescence in Tumor Diagnosis and Treatment: A Review

Malignant tumors rank as a leading cause of death worldwide. Accurate diagnosis and advanced treatment options are crucial to win battle against tumors. In recent years, Cherenkov luminescence (CL) has shown its technical advantages and clinical transformation potential in many important fields, particularly in tumor diagnosis and treatment, such as tumor detection in vivo, surgical navigation, radiotherapy, photodynamic therapy, and the evaluation of therapeutic effect. In this review, we summarize the advances in CL for tumor diagnosis and treatment. We first describe the physical principles of CL and discuss the imaging techniques used in tumor diagnosis, including CL imaging, CL endoscope, and CL tomography. Then we present a broad overview of the current status of surgical resection, radiotherapy, photodynamic therapy, and tumor microenvironment monitoring using CL. Finally, we shed light on the challenges and possible solutions for tumor diagnosis and therapy using CL.

External beam irradiation angle measurement using a hybrid Cerenkov-scintillation detector

Objective. In this study, we propose a novel approach designed to take advantage of the Cerenkov light angular dependency to perform a direct measurement of an external beam irradiation angle. Approach. A Cerenkov probe composed of a 10 mm long filtered sensitive volume of clear PMMA optical fibre was built. Both filtered and raw Cerenkov signals from the transport fibre were collected through a single 1 mm diameter transport fibre. An independent plastic scintillation detector composed of 10 mm BCF12 scintillating fibre was also used for simultaneous dose measurements. A first series of measurements aimed at validating the ability to account for the Cerenkov electron energy spectrum dependency by simultaneously measuring the deposited dose, thus isolating signal variations resulting from the angular dependency. Angular calibration curve for fixed dose irradiations and incident angle measurements using electron and photon beams where also achieved. Main results. The beam nominal energy was found to have a significant impact on the shapes of the angular calibration curves. This can be linked to the electron energy spectrum dependency of the Cerenkov emission cone. Irradiation angle measurements exhibit an absolute mean error of 1.86° and 1.02° at 6 and 18 MV, respectively. Similar results were obtained with electron beams and the absolute mean error reaches 1.97°, 1.66°, 1.45° and 0.95° at 9, 12, 16 and 20 MeV, respectively. Reducing the numerical aperture of the Cerenkov probe leads to an increased angular dependency for the lowest energy while no major changes were observed at higher energy. This allowed irradiation angle measurements at 6 MeV with a mean absolute error of 4.82°. Significance. The detector offers promising perspectives as a potential tool for future quality assurance applications in radiotherapy, especially for stereotactic radiosurgery (SRS), magnetic resonance image-guided radiotherapy (MRgRT) and brachytherapy applications.

Color Cherenkov imaging of clinical radiation therapy

Color vision is used throughout medicine to interpret the health and status of tissue. Ionizing radiation used in radiation therapy produces broadband white light inside tissue through the Cherenkov effect, and this light is attenuated by tissue features as it leaves the body. In this study, a novel time-gated three-channel camera was developed for the first time and was used to image color Cherenkov emission coming from patients during treatment. The spectral content was interpreted by comparison with imaging calibrated tissue phantoms. Color shades of Cherenkov emission in radiotherapy can be used to interpret tissue blood volume, oxygen saturation and major vessels within the body.

Optimization of in vivo Cherenkov imaging dosimetry via spectral choices for ambient background lights and filtering

SIGNIFICANCE

The Cherenkov emission spectrum overlaps with that of ambient room light sources. Choice of room lighting devices dramatically affects the efficient detection of Cherenkov emission during patient treatment.

AIM

To determine optimal room light sources allowing Cherenkov emission imaging in normally lit radiotherapy treatment delivery rooms.

APPROACH

A variety of commercial light sources and long-pass (LP) filters were surveyed for spectral band separation from the red to near-infrared Cherenkov light emitted by tissue. Their effects on signal-to-noise ratio (SNR), Cherenkov to background signal ratio, and image artifacts were quantified by imaging irradiated tissue equivalent phantoms with an intensified time-gated CMOS camera.

RESULTS

Because Cherenkov emission from tissue lies largely in the near-infrared spectrum, a controlled choice of ambient light that avoids this spectral band is ideal, along with a camera that is maximally sensitive to it. An RGB LED light source produced the best SNR out of all sources that mimic room light temperature. A 675-nm LP filter on the camera input further reduced ambient light detected (optical density > 3), achieving maximal SNR for Cherenkov emission near 40. Reduction of the room light signal reduced artifacts from specular reflection on the tissue surface and also minimized spurious Cherenkov signals from non-tissue features such as bolus.

CONCLUSIONS

LP filtering during image acquisition for near-infrared light in tandem with narrow band LED illuminated rooms improves image quality, trading off the loss of red wavelengths for better removal of room light in the image. This spectral filtering is also critically important to remove specular reflection in the images and allow for imaging of Cherenkov emission through clear bolus. Beyond time-gated external beam therapy systems, the spectral separation methods can be utilized for background removal for continuous treatment delivery methods including proton pencil beam scanning systems and brachytherapy.

Survey of X-ray induced Cherenkov excited fluorophores with potential for human use

X-ray induced molecular luminescence (XML) is a phenomenon that can be utilized for clinical, deep-tissue functional imaging of tailored molecular probes. In this study, a survey of common or clinically approved fluorophores was carried out for their megavoltage X-ray induced excitation and emission characteristics. We find that direct scintillation effects and Cherenkov generation are two possible ways to cause these molecules' excitation. To distinguish the contributions of each excitation mechanism, we exploited the dependency of Cherenkov radiation yield on X-ray energy. The probes were irradiated by constant dose of 6 MV and 18 MV X-ray radiation, and their relative emission intensities and spectra were quantified for each X-ray energy pair. From the ratios of XML, yield for 6 MV and 18 MV irradiation we found that the Cherenkov radiation dominated as an excitation mechanism, except for aluminum phthalocyanine, which exhibited substantial scintillation. The highest emission yields were detected from fluorescein, proflavin and aluminum phthalocyanine, in that order. XML yield was found to be affected by the emission quantum yield, overlap of the fluorescence excitation and Cherenkov emission spectra, scintillation yield. Considering all these factors and XML emission spectrum respective to tissue optical window, aluminum phthalocyanine offers the best XML yield for deep tissue use, while fluorescein and proflavine are most useful for subcutaneous or superficial use.

Estimation of diffuse Cherenkov optical emission from external beam radiation build-up in tissue

SIGNIFICANCE

Optical imaging of Cherenkov emission during radiation therapy could be used to verify dose delivery in real-time if a more comprehensive quantitative understanding of the factors affecting emission intensity could be developed.

AIM

This study aims to explore the change in diffuse Cherenkov emission intensity with x-ray beam energy from irradiated tissue, both theoretically and experimentally.

APPROACH

Derivation of the emitted Cherenkov signal was achieved using diffusion theory, and experimental studies with 6 to 18 MV energy x-rays were performed in tissue phantoms to confirm the model predictions as related to the radiation build-up factor with depth into tissue.

RESULTS

Irradiation at lower x-ray energies results in a greater surface dose and higher build-up slope, which results in a ∼46  %   greater diffusely emitted Cherenkov signal per unit dose at 6 MV relative to 18 MV x-rays. However, this phenomenon competes with a decrease in signal from less Cherenkov photons being generated at lower energies, a ∼44  %   reduction at 6 versus 18 MV. The result is an emitted Cherenkov signal that is nearly constant with beam energy.

CONCLUSIONS

This study explains why the observed Cherenkov emission from tissue is not a strong function of beam energy, despite the known strong correlation between Cherenkov intensity and particle energy in the absence of build-up and scattering effects.

Optical emission-based phantom to verify coincidence of radiotherapy and imaging isocenters on an MR-linac

Purpose

Demonstrate a novel phantom design using a remote camera imaging method capable of concurrently measuring the position of the x‐ray isocenter and the magnetic resonance imaging (MRI) isocenter on an MR‐linac.

Methods

A conical frustum with distinct geometric features was machined out of plastic. The phantom was submerged in a small water tank, and aligned using room lasers on a MRIdian MR‐linac (ViewRay Inc., Cleveland, OH). The phantom physical isocenter was visualized in the MR images and related to the DICOM coordinate isocenter. To view the x‐ray isocenter, an intensified CMOS camera system (DoseOptics LLC., Hanover, NH) was placed at the foot of the treatment couch, and centered such that the optical axis of the camera was coincident with the central axis of the treatment bore. Two or four 8.3mm x 24.1cm beams irradiated the phantom from cardinal directions, producing an optical ring on the conical surface of the phantom. The diameter of the ring, measured at the peak intensity, was compared to the known diameter at the position of irradiation to determine the Z‐direction offset of the beam. A star‐shot method was employed on the front face of the frustum to determine X‐Y alignment of the MV beam. Known shifts were applied to the phantom to establish the sensitivity of the method.

Results

Couch translations, demonstrative of possible isocenter misalignments, on the order of 1mm were detectable for both the radiotherapy and MRI isocenters. Data acquired on the MR‐linac demonstrated an average error of 0.28mm(N=10, R²=0.997, σ=0.37mm) in established Z displacement, and 0.10mm(N=5, σ=0.34mm) in XY directions of the radiotherapy isocenter.

Conclusions

The phantom was capable of measuring both the MRI and radiotherapy treatment isocenters. This method has the potential to be of use in MR‐linac commissioning, and could be streamlined to be valuable in daily constancy checks of isocenter coincidence.

A review of recent and emerging approaches for the clinical application of Cerenkov luminescence imaging

Cerenkov luminescence (CL) is a blue-weighted emission of light produced by a vast array of clinically approved radioisotopes and LINAC accelerators. When β particles (emitted during the decay of radioisotopes) are present in a medium such as water or tissue, they are able to travel faster than the speed of light in that medium and in doing so polarize the molecules around them. Once the particle has left the local area, the polarized molecules relax and return to their baseline state releasing the additional energy as light (luminescence). This blue glow has commonly been used to determine the output of nuclear power plant cores and, in recent years, has found traction in the preclinical and clinical imaging field. This brief review will discuss the technology which has enabled the emergence of the biomedical Cerenkov imaging field, recent pre-clinical studies with potential clinical translation of Cerenkov luminescence imaging (CLI) and the current clinical implementations of the method. Finally, an outlook is given as to the direction in which the field is heading.

Spatial and temporal dosimetry of individual electron FLASH beam pulses using radioluminescence imaging

Purpose.In this study, spatio-temporal beam profiling for electron ultra-high dose rate (UHDR; >40 Gy s-1) radiation via Cherenkov emission and radioluminescence imaging was investigated using intensified complementary metal-oxide-semiconductor cameras.Methods.The cameras, gated to FLASH optimized linear accelerator pulses, imaged radioluminescence and Cherenkov emission incited by single pulses of a UHDR (>40 Gy s-1) 10 MeV electron beam delivered to the isocenter. Surface dosimetry was investigated via imaging Cherenkov emission or scintillation from a solid water phantom or Gd2O2S:Tb screen positioned on top of the phantom, respectively. Projected depth-dose profiles were imaged from a tank filled with water (Cherenkov emission) and a 1 g l-1quinine sulfate solution (scintillation). These optical results were compared with projected lateral dose profiles measured by Gafchromic film at different depths, including the surface.Results.The per-pulse beam output from Cherenkov imaging agreed with the photomultiplier tube Cherenkov output to within 3% after about the first five to seven ramp-up pulses. Cherenkov emission and scintillation were linear with dose (R2 = 0.987 and 0.995, respectively) and independent of dose rate from ∼50 to 300 Gy s-1(0.18-0.91 Gy/pulse). The surface dose distribution from film agreed better with scintillation than with Cherenkov emission imaging (3%/3 mm gamma pass rates of 98.9% and 88.8%, respectively). Using a 450 nm bandpass filter, the quinine sulfate-based water imaging of the projected depth optical profiles agreed with the projected film dose to within 5%.Conclusion.The agreement of surface dosimetry using scintillation screen imaging and Gafchromic film suggests it can verify the consistency of daily beam quality assurance parameters with an accuracy of around 2% or 2 mm. Cherenkov-based surface dosimetry was affected by the target's optical properties, prompting additional calibration. In projected depth-dose profiling, scintillation imaging via spectral suppression of Cherenkov emission provided the best match to film. Both camera-based imaging modalities resolved dose from single UHDR beam pulses of up to 60 Hz repetition rate and 1 mm spatial resolution.

Increase in the intensity of an optical signal with fluorescein during proton and carbon-ion irradiation

Purpose

Although the imaging of luminescence emitted in water during irradiation of protons and carbon ions is a useful method for range and dose estimations, the intensity of the images is relatively low due to the low photon production of the luminescence phenomenon. Therefore, a relatively long time is required for the imaging. Since a fluorescent dye, fluorescein, may increase the intensity of the optical signal, we measured the luminescence images of water with different concentrations of fluorescein during irradiation of protons and carbon ions and compared the results with those by measurements with water.

Methods

A cooled charge‐coupled device (CCD) camera was used for imaging a water phantom with different concentrations of fluorescein from 0.0063 to 0.025 mg/cm³, in addition to a water phantom without fluorescein during irradiation of 150‐MeV protons and 241.5‐MeV/n carbon ions.

Results

For both protons and carbon ions, the intensity of the luminescence images increased as the concentration of fluorescein increased. With a fluorescein concentration of 0.025 mg/cm³, the intensities increased to more than 10 times those of water for both protons and carbon ions. Although the shape of the depth profiles of luminescence images of water with fluorescein appeared similar to that of water for protons, those for carbon ions were different from those of water due to the increase in the Cherenkov light component at shallow depths by the decrease in the angular dependencies of the Cherenkov light.

Conclusion

We confirmed the increase in intensity of the luminescence of water by adding fluorescein for particle ions. With a small amount of Cherenkov light contamination in the images, such as protons, the relative distributions of the luminescence images with fluorescein were similar to that of water and will be used for range or dose determination in a short time.

Visual Isocenter Position Enhanced Review (VIPER): a Cherenkov imaging-based solution for MR-linac daily QA

PURPOSE

This study demonstrates a robust Cherenkov imaging-based solution to MR-Linac daily QA, including mechanical-imaging-radiation isocenter coincidence verification.

METHODS

A fully enclosed acrylic cylindrical phantom was designed to be mountable to the existing jig, indexable to the treatment couch. An ABS plastic conical structure was fixed inside the phantom, held in place with 3D-printed spacers, and filled with water allowing for high edge contrast on MR imaging scans. Both a star shot plan and a four-angle sheet beam plan were delivered to the phantom; the former allowed for radiation isocenter localization in the x-z plane (A/P and L/R directions) relative to physical landmarks on the phantom, and the latter allowed for the longitudinal position of the sheet beam to be encoded as a ring of Cherenkov radiation emitted from the phantom, allowing for isocenter localization on the y-axis (S/I directions). A custom software application was developed to perform near-real-time analysis of the data by any clinical user.

RESULTS

Calibration procedures show that linearity between longitudinal position and optical ring diameter is high (R²  > 0.99), and that RMSE is low (0.184 mm). The star shot analysis showed a minimum circle radius of 0.34 mm. The final isocenter coincidence measurements in the lateral, longitudinal, and vertical directions were -0.61 mm, 0.55 mm, and -0.14 mm, respectively, and the total 3D distance coincidence was 0.83 mm, with each of these being below 2 mm tolerance.

CONCLUSION

This novel system provided an efficient, MR safe, all-in-one method for acquisition and near-real-time analysis of isocenter coincidence data. This represents a direct measurement of the 3D isocentricity. The combination of this phantom and the custom analysis application makes this solution readily clinically deployable after the longitudinal analysis of performance consistency.

Technical Note: Single-pulse beam characterization for FLASH-RT using optical imaging in a water tank

PURPOSE

High dose rate conditions, coupled with problems related to small field dosimetry, make dose characterization for FLASH-RT challenging. Most conventional dosimeters show significant dependence on dose rate at ultra-high dose rate conditions or fail to provide sufficiently fast temporal data for pulse to pulse dosimetry. Here fast 2D imaging of radioluminescence from a water and quinine phantom was tested for dosimetry of individual 4 μs linac pulses.

METHODS

A modified clinical linac delivered an electron FLASH beam of >50 Gy/s to clinical isocenter. This modification removed the x-ray target and flattening filter, leading to a beam that was symmetric and gaussian, as verified with GafChromic EBT-XD film. Lateral projected 2D dose distributions for each linac pulse were imaged in a quinine-doped water tank using a gated intensified camera, and an inverse Abel transform reconstruction provided 3D images for on-axis depth dose values. A total of 20 pulses were delivered with a 10 MeV, 1.5 cm circular beam, and beam with jaws wide open (40 × 40 cm2 ), and a 3D dose distribution was recovered for each pulse. Beam output was analyzed on a pulse by pulse basis.

RESULTS

The Rp , Dmax , and the R50 measured with film and optical methods agreed to within 1 mm for the 1.5 cm circular beam and the beam with jaws wide open. Cross beam profiles for both beams agreed with film data with >95% passing rate (2%/2 mm gamma criteria). The optical central axis depth dose agreed with film data, except for near the surface. A temporal pulse analysis revealed a ramp-up period where the dose per pulse increased for the first few pulses and then stabilized.

CONCLUSIONS

Optical imaging of radioluminescence was presented as a valuable tool for establishing a baseline for the recently initiated electron FLASH beam at our institution.

Monte Carlo modeling of the influence of strong magnetic fields on the stem-effect in plastic scintillation detectors used in radiotherapy dosimetry

PURPOSE

To investigate the impact of strong magnetic fields on the stem-effect in plastic scintillation detectors (PSDs) using Monte Carlo methods.

METHODS

Prior to building the light guide model, the properties of the Čerenkov process in GEANT4 were investigated by simulating depth-dose and depth-Čerenkov emission profiles in water as functions of Čerenkov process input parameters. In addition, profile simulations were performed for magnetic field strengths ranging from 0 T to 1.5 T. A PMMA light guide was constructed in GEANT4 using data from the manufacturer and literature. Simulations were performed with the model as functions of depth and fiber-beam angle where the simulated stem-effect spectrum and the Čerenkov light ratio (CLR) were scored and compared to measured data in the literature. The light guide optical properties were iteratively adjusted until agreement between the simulated and measured data was achieved. Simulations were performed with the validated model as functions of depth and magnetic field strength and the simulated data were compared to measured data in the literature. The model was also used to evaluate the sensitivity of the CLR to the various optical properties of the light guide in different irradiation conditions.

RESULTS

No significant changes in the depth-dose or depth-Čerenkov emission profiles were observed with step-size restrictions imposed by the Čerenkov process input parameters, which was attributed to the condensed history algorithm and transport parameters used in this work. Similar changes in the depth-dose and depth-Čerenkov emission profiles were observed with increasing magnetic field strength, which indicates the Čerenkov process is not adversely impacted by the presence of the magnetic field. Following optimization of the light guide optical properties, agreement within two standard deviations was observed between the simulated and measured optical data for all validation geometries considered. Agreement within one standard deviation was observed between the simulated and measured data for all depths and field strengths ≥0 T whereas discrepancies were observed for magnetic field strengths <-0.35 T. These significant differences were attributed to insufficient measurement data for this irradiation configuration during model validation. Of the light guide optical properties investigated, the fluorescence signal had the greatest impact on the CLR sensitivity to the magnetic field.

CONCLUSIONS

No significant change in the Čerenkov emission per dose in water was observed for magnetic field strengths up to 1.5 T. The nominal fiber fluorescence signal was found to have a significant impact on the CLR sensitivity to varying irradiation conditions where changes up to 11.7% were observed whereas the mirror reflectivity and fiber attenuation had a modest impact with maximum CLR changes of 2.6% and 1.2% relative to 0 T, respectively. The results of this work suggest light guides with low fiber fluorescence should be used with PSDs for dosimetry measurements in magnetic fields to minimize the impact of the magnetic field on the CLR correction.

Review of in vivo optical molecular imaging and sensing from x-ray excitation

SIGNIFICANCE

Deep-tissue penetration by x-rays to induce optical responses of specific molecular reporters is a new way to sense and image features of tissue function in vivo. Advances in this field are emerging, as biocompatible probes are invented along with innovations in how to optimally utilize x-ray sources.

AIM

A comprehensive review is provided of the many tools and techniques developed for x-ray-induced optical molecular sensing, covering topics ranging from foundations of x-ray fluorescence imaging and x-ray tomography to the adaptation of these methods for sensing and imaging in vivo.

APPROACH

The ways in which x-rays can interact with molecules and lead to their optical luminescence are reviewed, including temporal methods based on gated acquisition and multipoint scanning for improved lateral or axial resolution.

RESULTS

While some known probes can generate light upon x-ray scintillation, there has been an emergent recognition that excitation of molecular probes by x-ray-induced Cherenkov light is also possible. Emission of Cherenkov radiation requires a threshold energy of x-rays in the high kV or MV range, but has the advantage of being able to excite a broad range of optical molecular probes. In comparison, most scintillating agents are more readily activated by lower keV x-ray energies but are composed of crystalline inorganic constituents, although some organic biocompatible agents have been designed as well. Methods to create high-resolution structured x-ray-optical images are now available, based upon unique scanning approaches and/or a priori knowledge of the scanned x-ray beam geometry. Further improvements in spatial resolution can be achieved by careful system design and algorithm optimization. Current applications of these hybrid x-ray-optical approaches include imaging of tissue oxygenation and pH as well as of certain fluorescent proteins.

CONCLUSIONS

Discovery of x-ray-excited reporters combined with optimized x-ray scan sequences can improve imaging resolution and sensitivity.

Imaging of polarized components of Cerenkov light and luminescence of water during carbon-ion irradiation

PURPOSE

The luminescence image of water during the irradiation of carbon ions showed higher intensity at shallow depths than dose distribution due to the contamination of Cerenkov light from secondary electrons. Since Cerenkov light is coherent and polarized for the light produced during the irradiation of carbon ions to water, the reduction of Cerenkov light may be possible with a polarizer. In addition, there is no information on the polarization of the luminescence of water. To clarify these points, we measured the optical images of water during the irradiation of carbon ions with a polarizer by changing the directions of the transmission axis.

METHODS

Imaging was conducted using a cooled charge-coupled device (CCD) camera during the irradiation of 241.5 MeV/n energy carbon ions to a water phantom with a polarizer in front of the lens by changing the transmission axis parallel and perpendicular to the carbon-ion beam.

RESULTS

With the polarizer parallel to the carbon-ion beam, the intensity at the shallow depth was ~26% higher than that measured with the polarizer perpendicular to the beam. We found no significant intensity difference between these two images at deeper depths where the Cerenkov light was not included. The difference image of the parallel and perpendicular directions showed almost the same image as the simulated Cerenkov light distribution. Using the measured difference image, correction of the Cerenkov component was possible from the measured luminescence image of water during the irradiation of carbon ions.

CONCLUSION

We could measure the difference of the Cerenkov light component by changing the transmission axis of the polarizer. Also we clarified that there was no difference in the luminescence of water by changing the transmission axis of the polarizer.

Theoretical lateral and axial sensitivity limits and choices of molecular reporters for Cherenkov-excited luminescence in tissue during x-ray beam scanning

PURPOSE

Unlike fluorescence imaging utilizing an external excitation source, Cherenkov emissions and Cherenkov-excited luminescence occur within a medium when irradiated with high-energy x-rays. Methods to improve the understanding of the lateral spread and axial depth distribution of these emissions are needed as an initial step to improve the overall system resolution.

METHODS

Monte Carlo simulations were developed to investigate the lateral spread of thin sheets of high-energy sources and compared to experimental measurements of similar sources in water. Additional simulations of a multilayer skin model were used to investigate the limits of detection using both 6- and 18-MV x-ray sources with fluorescence excitation for inclusion depths up to 1 cm.

RESULTS

Simulations comparing the lateral spread of high-energy sources show approximately 100  ×   higher optical yield from electrons than photons, although electrons showed a larger penumbra in both the simulations and experimental measurements. Cherenkov excitation has a roughly inverse wavelength squared dependence in intensity but is largely redshifted in excitation through any distance of tissue. The calculated emission spectra in tissue were convolved with a database of luminescent compounds to produce a computational ranking of potential Cherenkov-excited luminescence molecular contrast agents.

CONCLUSIONS

Models of thin x-ray and electron sources were compared with experimental measurements, showing similar trends in energy and source type. Surface detection of Cherenkov-excited luminescence appears to be limited by the mean free path of the luminescence emission, where for the given simulation only 2% of the inclusion emissions reached the surface from a depth of 7 mm in a multilayer tissue model.

Discovery of the luminescence of water during irradiation of radiation at a lower energy than the Cherenkov light threshold

It is widely believed that light is not emitted in water during irradiation of radiation at energies lower than the Cherenkov light threshold. Contrary to this consensus, we discovered that light (luminescence) is emitted in water during irradiation of radiation, and imaging of this luminescence was possible. In this review, the author describes the optical images obtained for various types of radiation, their characteristics and origins, and potential applications of the luminescence of water during irradiation at a lower energy than the Cherenkov light threshold. The author also describes the luminescence of other transparent materials and future prospects of the discovered luminescence.

Step-size effect on calculated photon and electron beam Cherenkov-to-dose conversion factors

PURPOSE

Previous work presented and validated in-water Cherenkov emission (CE)-based radiotherapy dosimetry. Condensed history Monte Carlo (MC)-calculated electron beam CE-to-dose conversion with <4π CE detection, however, could exhibit step-size dependence. This work presents a physics update and numerical study of this step-size dependence in photon and electron beams, elucidates the CE generation physics, and guides further research.

METHODS

The CE-to-dose conversion, k_C^θ±δθ, is calculated for photons (6X, 15X) and electrons (6E, 20E) on-axis in-water with: θ±δθ∈{90°±90°(4π),90°±5°,45°±45°,90°±45°}, 10 cm equivalent square, 100 cm SSD, 1cm voxel radius and beam-dependent length. Relative deviation from single-scattering (SS) simulation is evaluated on maximum fractional electron step energy loss ESTEPE∈0.01-0.25. Standard uncertainties (k=1, 10⁸histories) are reported. A simplified method considering only the straight step direction is also implemented.

RESULTS

No significant step-size effect (>0.1%) was observed for dose and all k_C^θ±δθ, except for surface dosimetry at 90°±5° (-1.6%±0.5%, 20E), which is not recommended. Electron SS deviation uncertainties (k=1), otherwise, varied from <0.2% overall to <0.1% with large apertures. Photon uncertainties varied from <1.1% overall to <0.2% non-superficially with large apertures. The simplified straight-step method exhibited overall greater deviation from SS, most notably -2.8%±0.1% (6E) and -2.5%±0.4% (20E) superficially with 90°±45°, and -1.4%±0.3% (6X) and -0.6%±0.2% (15X) non-superficially with 90°±5° for ESTEPE∈[0.10,0.25].

CONCLUSIONS

We demonstrate step-size independence of newly-implemented correction in EGSnrc directional Cherenkov calculations. This advances clinical CE-based dosimetry and is useful for the general Monte Carlo community.

Cherenkov Luminescence Imaging for Assessment of Radioactive Plaque Position in Brachytherapy of Uveal Melanoma: An In Vivo Feasibility Study

Purpose

To study the feasibility of using Cherenkov luminescence imaging (CLI) to evaluate and document ruthenium-106 plaque position during brachytherapy of uveal melanoma.

Methods

Ruthenium-106 decays by emitting high-energy beta particles. When the electrons pass through the eye, Cherenkov radiation generates a faint light that can be captured by highly sensitive cameras. Patients undergoing ruthenium-106 plaque brachytherapy for posteriorly located choroidal melanoma were examined by CLI, which was performed in complete darkness with an electron multiplying charged-coupled device camera mounted on a fundus camera modified for long exposures.

Results

Ten patients with tumors ranging from 5.8 to 13.0 mm in largest basal diameter and 2.0 to 4.6 mm in height were included. The plaques had an activity between 0.035 and 0.089 MBq/mm² at the time of examination (1–4 days after implantation). CLI revealed the actual plaque position by displaying a circular area of light in the fundus corresponding with the plaque area. The Cherenkov light surrounded the tumor as a halo, which showed some asymmetry when the plaque was slightly displaced. The light intensity correlated positively with plaque activity and negatively with tumor pigmentation. Exposure times between 30 and 60 seconds were required to display the plaque position and delineate the tumor area. The long exposures made it difficult to maintain stable eye fixation and optimal image quality.

Conclusions

CLI is a novel method to assess and document ruthenium-106 plaque position in brachytherapy for uveal melanoma.

Translational Relevance

Ocular CLI may provide relevant radiation data during and after implantation of radioactive plaques, thus improving the accuracy of episcleral brachytherapy.

Imaging radiation dose in breast radiotherapy by X-ray CT calibration of Cherenkov light

Imaging Cherenkov emission during radiation therapy cancer treatments can provide a real-time, non-contact sampling of the entire dose field. The emitted Cherenkov signal generated is proportional to deposited dose, however, it is affected by attenuation from the intrinsic tissue optical properties of the patient, which in breast, ranges from primarily adipose to fibroglandular tissue. Patients being treated with whole-breast X-ray radiotherapy (n = 13) were imaged for 108 total fractions, to establish correction factors from the linear relationships between Cherenkov light and CT number (HU). This study elucidates this relationship in vivo, and a correction factor approach is used to scale each image to improve the linear correlation between Cherenkov emission intensity and dose ([Formula: see text]). This study provides a major step towards direct quantitative radiation dose imaging in humans by utilizing non-contact camera sensing of Cherenkov emission during the radiation therapy treatment.

Measurements of temporal response of luminescence of water at lower energy than Cerenkov-light threshold during carbon-ion irradiation

Although the luminescence of water at lower energy than the Cerenkov-light threshold during carbon-ion irradiation was found and imaging was possible, the temporal response has not been measured, and so the difference from Cerenkov-light remains unclear. To clarify this point, we measured the temporal response of the luminescence of water at lower energy than the Cerenkov-light threshold and compared it with that of Cerenkov-light. We used silicon photomultiplier (Si-PM) modules to measure the temporal response at the Bragg peak area of a water phantom during irradiation of the carbon ion where the Cerenkov-light was not included. We also measured the temporal response at the shallow depth of the water phantom where the Cerenkov-light was included. In both areas, we measured the temporal waveforms of the light produced by the irradiation of the carbon ions in which the ripples of spills were clearly observed. We found no difference in the waveforms between the Bragg peak and the shallow depths of water. Our results do not contradict the hypothesis that the luminescence of water and Cerenkov-light are produced by the same mechanism.

Optical imaging method to quantify spatial dose variation due to the electron return effect in an MR-linac

PURPOSE

Treatment planning systems (TPSs) for MR-linacs must employ Monte Carlo-based simulations of dose deposition to model the effects of the primary magnetic field on dose. However, the accuracy of these simulations, especially for areas of tissue-air interfaces where the electron return effect (ERE) is expected, is difficult to validate due to physical constraints and magnetic field compatibility of available detectors. This study employs a novel dosimetric method based on remotely captured, real-time optical Cherenkov and scintillation imaging to visualize and quantify the ERE.

METHODS

An intensified CMOS camera was used to image two phantoms with designed ERE cavities. Phantom A was a 40 cm × 10 cm × 10 cm clear acrylic block drilled with five holes of increasing diameters (0.5, 1, 2, 3, 4 cm). Phantom B was a clear acrylic block (25 cm × 20 cm × 5 cm) with three cavities of increasing diameter (3, 2, 1 cm) split into two halves in the transverse plane to accommodate radiochromic film. Both phantoms were imaged while being irradiated by 6 MV flattening filter free (FFF) beams within a MRIdian Viewray (Viewray, Cleveland, OH) MR-linac (0.34 T primary field). Phantom A was imaged while being irradiated by 6 MV FFF beams on a conventional linac (TrueBeam, Varian Medical Systems, San Jose, CA) to serve as a control. Images were post processed in Matlab (Mathworks Inc., Natick, MA) and compared to TPS dose volumes.

RESULTS

Control imaging of Phantom A without the presence of a magnetic field supports the validity of the optical image data to a depth of 6 cm. In the presence of the magnetic field, the optical data shows deviations from the commissioned TPS dose in both intensity and localization. The largest air cavity examined (3 cm) indicated the largest dose differences, which were above 20% at some locations. Experiments with Phantom B illustrated similar agreement between optical and film dosimetry comparisons with TPS data in areas not affected by ERE.

CONCLUSION

There are some appreciable differences in dose intensity and spatial dose distribution observed between the novel experimental data set and the dose models produced by the current clinically implemented MR-IGRT TPS.

Cherenkov imaging for total skin electron therapy (TSET)

BACKGROUND

Total skin electron therapy (TSET) utilizes high-energy electrons to treat malignancies on the entire body surface. The otherwise invisible radiation beam can be observed via the optical Cherenkov photons emitted from interactions between the high-energy electron beam and tissue.

METHODS AND MATERIALS

With a time-gated intensified camera system, the Cherenkov emission can be used to evaluate the dose uniformity on the surface of the patient in real time. Fifteen patients undergoing TSET in various conditions (whole body and half body) were imaged and analyzed. Each patient was monitored during TSET via in vivo detectors (IVD) in nine locations. For accurate Cherenkov imaging, a comparison between IVD and Cherenkov profiles was conducted using a polyvinyl chloride board to establish the perspective corrections.

RESULTS AND DISCUSSION

With proper corrections developed in this study including the perspective and inverse square corrections, the Cherenkov imaging provided two-dimensional maps proportional to dose and projected on patient skin. The results of ratio between chest and umbilicus points were in good agreement with in vivo point dose measurements, with a standard deviation of 2.4% compared to OSLD measurements.

CONCLUSIONS

Cherenkov imaging is a viable tool for validating patient-specific dose distributions during TSET.

Assessment of imaging Cherenkov and scintillation signals in head and neck radiotherapy

The goal of this study was to test the utility of time-gated optical imaging of head and neck (HN) radiotherapy treatments to measure surface dosimetry in real-time and inform possible interfraction replanning decisions. The benefit of both Cherenkov and scintillator imaging in HN treatments is direct daily feedback on dose, with no change to the clinical workflow. Emission from treatment materials was characterized by measuring radioluminescence spectra during irradiation and comparing emission intensities relative to Cherenkov emission produced in phantoms and scintillation from small plastic targets. HN treatment plans were delivered to a phantom with bolus and mask present to measure impact on signal quality. Interfraction superficial tumor reduction was simulated on a HN phantom, and cumulative Cherenkov images were analyzed in the region of interest (ROI). HN human patient treatment was imaged through the mask and compared with the dose distribution calculated by the treatment planning system. The relative intensity of radioluminescence from the mask was found to be within 30% of the Cherenkov emission intensity from tissue-colored clay. A strong linear relationship between normalized cumulative Cherenkov intensity and tumor size was established ([Formula: see text]). The presence of a mask above a scintillator ROI was found to decrease mean pixel intensity by  >40% and increase distribution spread. Cherenkov imaging through mask material is shown to have potential for surface field verification and tracking of superficial anatomy changes between treatment fractions. Imaging of scintillating targets provides a direct imaging of surface dose on the patient and through transparent bolus material. The first imaging of a patient receiving HN radiotherapy was achieved with a signal map which qualitatively matches the surface dose plan.

Technical Note: Quality assurance and relative dosimetry testing of a 60 Co total body irradiator using optical imaging

PURPOSE

The aim of this study was to create an optical imaging-based system for quality assurance (QA) testing of a dedicated Co-60 total body irradiation (TBI) machine. Our goal is to streamline the QA process by minimizing the amount time necessary for tests such as verification of dose rate and field homogeneity.

METHODS

Plastic scintillating rods were placed directly on the patient treatment couch of a dedicated TBI ⁶⁰ Co irradiator. A tripod-mounted intensified camera was placed directly adjacent to the couch. Images were acquired over a 30-s period once the cobalt source was fully exposed. Real-time image filtering was used; cumulative images were flatfield corrected as well as background and darkfield subtracted. Scintillators were used to measure light-radiation field correspondence, dose rate, field homogeneity, and symmetry. Dose rate effects were measured by modifying the height of the treatment couch and scintillator response was compared to ionization chamber (IC) measurements. Optically stimulated luminesce detector (OSLD) used as reference dosimeters during field symmetry and homogeneity testing.

RESULTS

The scintillator-based system accurately reported changes in dose rate. When comparing normalized output values for IC vs scintillators over a range of source-to-surface distances, a linear relationship (R²  = 0.99) was observed. Normalized scintillator signal matched OSLD measurements with <1.5% difference during field homogeneity and symmetry testing. Beam symmetry across both axes of the field was within 2%. The light field was found to correspond to 90 ± 3% of the isodose maximum along the longitudinal and latitudinal axis, respectively. Scintillator imaging output results using a single image stack requiring no postexposure processing (needed for OSLD) or repeat manual measurements (needed for IC).

CONCLUSION

Imaging of scintillation light emission from plastic rods is a viable and efficient method for carrying out TBI ⁶⁰ Co irradiator QA. We have shown that this technique can accurately measure field homogeneity, symmetry, light-radiation field correspondence, and dose rate effects.

Estimation of the fractions of luminescence of water at higher energy than Cerenkov-light threshold for various types of radiation

Although the luminescence of water at a lower energy than the Cerenkov-light (CL) threshold has been found for various types of radiation, the fractions of the luminescence of water to the total produced light have not been obvious for radiations at a higher energy than the CL threshold because it is difficult to separate these two types of light. Thus, we used a Monte Carlo simulation to estimate the fractions of the luminescence of water for various types of radiation at a higher energy than the CL threshold to confirm the major component of the produced light. After we confirmed that the estimated light production of the luminescence of water could adequately simulate the experimental results, we calculated the produced light photons of this luminescence and the CL from water for protons (170 MeV), carbon ions (330 MeV/n), high-energy x-ray (6 MV) from a linear accelerator (LINAC), high-energy electrons (9 MeV) from LINAC, positrons (F-18, C-11, O-15, and N-13), and high-energy gamma photon radionuclides (Co-60). For protons, the major fraction of the produced light was the luminescence of water in addition to the CL from the prompt gamma photons produced by the nuclear interactions. For carbon ions, the major fraction of the produced light was the luminescence of water and the CL produced by the secondary electrons in addition to the prompt gamma photons produced by the nuclear interactions. For high-energy x-ray and electrons from LINAC, the fractions of luminescence of water were ∼0.1  %   to 0.2%. The fractions of luminescence of water for positrons were 0.2% to 1.5% and that for Co-60 was 0.4%. We conclude that the major fractions of light produced from x-ray and electrons from LINAC, positron radionuclides, and the Co-60 source are CL, with fractions of the luminescence of water from <0.1  %   to 1.5%.

Cherenkov emission-based external radiotherapy dosimetry: II. Electron beam quality specification and uncertainties

PURPOSE

Cherenkov emission (CE) is ubiquitous in external radiotherapy. It is also unique in that it carries the promise of 3D, micrometer-resolution, perturbation-free, in-water dosimetry with a beam quality-independent detector response calibration. Our aim is to bring CE-based dosimetry into the clinic and we motivate this here with electron beams. We Monte Carlo (MC) calculate and characterize broad-beam CE-to-dose conversion factors in water for a clinically representative library of electron beam qualities, address beam quality specification and reference depth selection, and develop a preliminary uncertainty budget based on our MC results and relative experimental work of a companion study (Paper I).

METHODS

Broad electron beam CE-to-dose conversion factors k C θ ± δ θ include CE generated at polar angles θ ± δθ on beam axis in water. With modifications to the EGSnrc code SPRRZnrc, k C θ ± δ θ factors are calculated for a total of 20 electron beam qualities from four BEAMnrc models (Varian Clinac 2100C/D, Clinac 21EX, TrueBeam, and Elekta Precise). We examine beam quality, depth, and detection angle dependence for θ ± δ θ = 90 ∘ ± 90 ∘ (4π detection), 90 ∘ ± 5 ∘ , 45 ∘ ± 45 ∘ , and 90 ∘ ± 45 ∘ . As discussed in Paper I, 4π detection offers the strongest CE-dose correlation and θ = 90 ∘ with small δθ is most practical. The two additional configurations are considered as a compromise between these two extremes. We address beam quality specification and reference depth selection in terms of the electron beam quality specifier R 50 , obtained from the depth of 50% CE C 50 , and derive a best-case uncertainty budget for the CE-based dosimetry formalism proposed in Paper I at each detection configuration.

RESULTS

The k C θ ± δ θ factor was demonstrated to capture variations in the beam spectrum, angle, photon contamination, and electron fluence below the CE threshold (∼260 keV in the visible) in accordance with theory. The root-mean-square deviation and maximum deviation of a second-order polynomial fit of simulated R 50 values in terms of C 50 were 0.05 and 0.11 mm at 4π and 0.20 and 0.33 mm at 90 ∘ ± 5 ∘ detection, respectively. The fit performance on experimental data in Paper I was in agreement with these values within experimental uncertainties (±1.5 mm, 95% CI). A two-term power function fit of k C θ ± δ θ in terms of R 50 at a reference depth d ref = a R 50 + b resulted in total d ref -dependent dose uncertainty contribution estimate of 0.8% and 1.1% and preliminary best-case estimate of the combined standard dose uncertainty of 1.1% and 1.3% at 4π and 90 ∘ ± 5 ∘ detection, respectively. The results and corresponding uncertainties with the two intermediate apertures were generally of the same order as the 4π case. In addition, a theoretically consistent downstream shift of the percent-depth CE (PDC) by the difference between R 50 and C 50 improved the depth dependence of the 4π conversion by an order of magnitude (±2.8%). Therefore, a large aperture centered on a θ value between 45 ∘ and 90 ∘ combined with a downstream PDC shift may be recommended for beam-axis CE-based electron beam dosimetry in water.

CONCLUSIONS

By delivering R 50 -based CE-to-dose conversion data and demonstrating the potential for dosimetric uncertainty on the order of 1%, we bring CE-based electron beam dosimetry closer to clinical realization.

Cherenkov emission-based external radiotherapy dosimetry: I. Formalism and feasibility

PURPOSE

Cherenkov emission (CE)-based external beam dosimetry is envisioned to involve the detection of CE directly in water with placement of a high-resolution detector out of the field, avoiding perturbations encountered with traditional dosimeters. In this work, we lay out the groundwork for its implementation in the clinic and motivate CE-based dosimeter design efforts. To that end, we examine a formalism for broad-beam in-water CE-based dosimetry of external radiotherapy beams, design and test a Monte Carlo (MC) simulation framework for the calculation of CE-to-dose conversion factors used by the formalism, and demonstrate the experimental feasibility of this method.

METHODS

The formalism is conceptually analogous to ionization-based dosimetry and employs CE-to-dose conversion factors, k C θ ± δ θ , including only and all CE generated within polar angles θ ± δθ on beam axis. The EGSnrc user code SPRRZnrc is modified to calculate k C θ ± δ θ , as well as CE spectral and angular distributions. The modified code is tested with monoenergetic parallel electrons on a thin water slab. Detector configurations are examined for broad 6-22 MeV electron beams from a BEAMnrc TrueBeam model, with a focus on θ ± δ θ = 90 ∘ ± 90 ∘ (4π detection), 90 ∘ ± 5 ∘ , and 42 ∘ ± 5 ∘ ( θ = 42 ∘ is the CE angle of relativistic electrons in water). We perform a relative experimental validation at 90 ∘ with electron beams, using a simple detector design with spherical optics and geometrical optics approximation of the sensitive volume, which spans the water tank. Due to transient charged particle equilibrium, broad photon beams are generally less sensitive to beam quality, depth, and angle.

RESULTS

For 0.1-50 MeV electrons on a thin water slab, the code outputs CE photon spectral density per unit mass (calculated from dose and k C θ ± δ θ ) and angle in agreement with theory within ±0.03% and ± 0 . 01 ∘ , respectively, corresponding to the output precision. The 42 ∘ configuration was found impractical due to detection considerations. Detection at 90 ∘ ± δ θ for small δθ exhibited beam quality dependence of the same order as well as strong superficial depth dependence. A 4π configuration ameliorates these effects. A more practical approach may employ a large numerical aperture. In comparing with literature, we find that these effects are less pronounced for broad photon beams in water, as expected. Measured relative k C 90 ∘ ± δ θ at small δθ were within 1% of simulated factors (relative to their local average) for percent-depth CE (PDC) >50%. At other depths, deviations were in accordance with signal-to-noise, known detector limitations, and approximations. It was found that the CE spectrum is beam quality and depth invariant, while for electron beams the CE angular distribution is strongly dependent on beam quality and depth. However, the uncertainty of CE and PDC measurement at 90 ∘ ± δ θ detection for small δθ due to ± 0 . 1 ∘ deviations around δθ was shown to be ≤1% and <0.1% (k = 1), respectively. The robustness to expected detector setup variations was found to result in ≤1% (k = 1) local uncertainty contribution for PDC >50%.

CONCLUSIONS

Based on our MC and experimental studies, we conclude that the CE-based method is promising for high-resolution, perturbation-free, three-dimensional dosimetry in water, with specific applications contingent on comprehensive detector development and characterization.

Radioluminescence in biomedicine: physics, applications, and models

The electromagnetic spectrum contains different frequency bands useful for medical imaging and therapy. Short wavelengths (ionizing radiation) are commonly used for radiological and radionuclide imaging and for cancer radiation therapy. Intermediate wavelengths (optical radiation) are useful for more localized imaging and for photodynamic therapy (PDT). Finally, longer wavelengths are the basis for magnetic resonance imaging and for hyperthermia treatments. Recently, there has been a surge of interest for new biomedical methods that synergize optical and ionizing radiation by exploiting the ability of ionizing radiation to stimulate optical emissions. These physical phenomena, together known as radioluminescence, are being used for applications as diverse as radionuclide imaging, radiation therapy monitoring, phototherapy, and nanoparticle-based molecular imaging. This review provides a comprehensive treatment of the physics of radioluminescence and includes simple analytical models to estimate the luminescence yield of scintillators and nanoscintillators, Cherenkov radiation, air fluorescence, and biologically endogenous radioluminescence. Examples of methods that use radioluminescence for diagnostic or therapeutic applications are reviewed and analyzed in light of these quantitative physical models of radioluminescence.

An investigation of clinical treatment field delivery verification using cherenkov imaging: IMRT positioning shifts and field matching

PURPOSE

Cherenkov light emission has been shown to correlate with ionizing radiation dose delivery in solid tissue. An important clinical application of Cherenkov light is the real-time verification of radiation treatment delivery in vivo. To test the feasibility of treatment field verification, Cherenkov light images were acquired concurrent with radiation beam delivery to standard and anthropomorphic phantoms. Specifically, we tested two clinical treatment scenarios: (a) Observation of field overlaps or gaps in matched 3D fields and (b) Patient positioning shifts during intensity modulated radiation therapy (IMRT) field delivery. Further development of this technique would allow real-time detection of treatment delivery errors on the order of millimeters so that patient safety and treatment quality can be improved.

METHODS

Cherenkov light emission was captured using a PI-MAX4 intensified charge coupled device (ICCD) system (Princeton Instruments). All radiation delivery was performed using a Varian Trilogy linear accelerator (linac) operated at 6 MV or 18 MV for photon and 6 MeV or 16 MeV for electron studies. Field matching studies were conducted with photon and electron beams at gantry angles of 0°, 15°, and 45°. For each modality and gantry angle, a total of three data sets were acquired. Overlap and gap distances of 0, 2, 5, and 10 mm were tested and delivered to solid phantom material of 30 × 30 × 5 cm³ . Phantom materials used were white plastic water and brown solid water. Tests were additionally performed on an anthropomorphic phantom with an irregular surface. Positioning shift studies were performed using IMRT fields delivered to a thoracic anthropomorphic phantom. For thoracic phantom measurements, the camera was placed laterally to observe the entire right side of the phantom. Fields were delivered with known translational patient positioning shifts in four directions. Changes in the Cherenkov fluence were evaluated through the generation of difference maps from unshifted Cherenkov images. All images were evaluated using ImageJ, Python, and MATLAB software packages.

RESULTS

For matched fields, Cherenkov images were able to quantitate matched field separations with discrepancies between 2 and 4 mm, depending on gantry angle and beam energy or modality. For all photon and electron beams delivered at a gantry angle of 0°, image analysis indicated average discrepancies of less than 2 mm for all field gaps and overlaps, with 83% of matched fields exhibiting discrepancies less than 1 mm. Beams delivered obliquely to the phantom surface exhibited average discrepancies as high as 4 mm for electron beams delivered at large oblique angles. Finally, for IMRT field delivery, vertical and lateral patient positioning shifts of 2 mm were detected in some cases, indicating the potential detectability threshold of using this technique alone.

CONCLUSIONS

Our study indicates that Cherenkov imaging can be used to support and bolster current treatment delivery verification techniques, improving our ability to recognize and rectify millimeter-scale delivery and positioning errors.

Rapid Multisite Remote Surface Dosimetry for Total Skin Electron Therapy: Scintillator Target Imaging

PURPOSE

The goal of this work is to produce a surface-dosimetry method capable of accurately and remotely measuring skin dose for patients undergoing total skin electron therapy (TSET) without the need for postexposure dosimeter processing. A rapid and wireless surface-dosimetry system was developed to improve clinical workflow. Scintillator-surface dosimetry was conducted on patients undergoing TSET by imaging scintillator targets with an intensified camera during TSET delivery.

METHODS AND MATERIALS

Disc-shaped scintillator targets were attached to the skin surface of patients undergoing TSET and imaged with an intensified, time-gated, and linear accelerator-synchronized camera. Optically stimulated luminescence dosimeters (OSLDs) were placed directly adjacent to scintillators at several dosimetry sites to serve as an absolute dose reference. Real-time image-processing methods were used to produce background-subtracted intensity maps of Cherenkov and scintillation emission. Rapid conversion of scintillator-light output to dose was achieved by using a custom fitting algorithm and calibration factor. Surface doses measured by scintillators were compared with those from OSLDs.

RESULTS

Absolute surface-dose measurements for 99 dosimetry sites were evaluated. According to paired OSLD estimates, scintillator dosimeters were able to report dose with <3% difference in 88 of 99 observed dosimetry sites and <5% difference in 98 of 99 observed dosimetry sites. Fitting a linear regression to dose data reported by scintillator versus OSLD, per dosimetry site, yielded an R² = 0.94.

CONCLUSIONS

Scintillators were able to report dose within <3% accuracy of OSLDs. Imaging of calibrated scintillator targets via an intensified, linear accelerator-synchronized camera provides rapid absolute surface-dosimetry measurements for patients treated with TSET. This technique has the potential to reduce the amount of time and effort necessary to conduct full-body dosimetry and can be adopted for use in any surface-dosimetry setting where the region of interest is observable throughout treatment.