Soda-lime silicate glass under hydrostatic pressure and indentation: a micro-Raman study

Determination of the Pressure Dependence of Raman Mode for an Alumina-Glass Pair in Hertzian Contact

Optimising the performance of materials requires, among other things, the characterisation of residual stresses during the design stage. Raman spectroscopy offers access to these residual stresses at the micrometre scale when this inelastic light scattering is active in these materials. In this case, the relationship between the Raman mode shift and the pressure must be known. High-pressure cells with diamond anvils or bending instruments coupled to Raman spectrometers are habitually used to determine this relationship. In this article, we propose a new method that involves a Hertzian contact to obtain this relationship. A device that compresses an alumina ball against a transparent glass plane is connected to a Raman spectrometer. Under these conditions, the contact pressure can be as high as 1.5 GPa. The contact between the glass plane and the ball is observed through a diaphragm. Several hundred Raman spectra are recorded depending on the contact diameter. The spectral profiles obtained represent the shift in the Raman modes of alumina and glass along the contact diameter. Hertz's theory accurately describes the pressure profile as a function of position for elastic materials. Therefore, the contact diameter can be measured by fitting the spectral profile with a function identical to the Hertz profile. We then deduce the maximum pressure. Next, the calculated pressure profile along the contact diameter is correlated with the spectral profile. We obtain a pressure dependence of the Raman mode with a coefficient equal to 2.07 cm-1/GPa for the Eg modes of alumina at 417 cm-1, which is in good agreement with the literature. In the case of glass, we refine the measurement of the Q3 mode shift at 1096 cm-1 in the studied pressure range compared to the literature. We find a coefficient of 4.31 cm-1/GPa. This work on static contacts opens up promising prospects for investigations into dynamic contacts in tribology.

Vibrational disorder and densification-induced homogenization of local elasticity in silicate glasses

We report the effect of structural compaction on the statistics of elastic disorder in a silicate glass, using heterogeneous elasticity theory with the coherent potential approximation (HET-CPA) and a log-normal distribution of the spatial fluctuations of the shear modulus. The object of our study, a soda lime magnesia silicate glass, is compacted by hot-compression up to 2 GPa (corresponding to a permanent densification of ~ 5%). Using THz vibrational spectroscopic data and bulk mechanical properties as inputs, HET-CPA evaluates the degree of disorder in terms of the length-scale of elastic fluctuations and the non-affine part of the shear modulus. Permanent densification decreases the extent of non-affine elasticity, resulting in a more homogeneous distribution of strain energy, while also decreasing the correlation length of elastic heterogeneity. Complementary 29Si magic angle spinning NMR spectroscopic data provide a short-range rationale for the effect of compression on glass structure in terms of a narrowing of the Si-O-Si bond-angle and the Si-Si distance.

Coupling Raman, Brillouin and Nd3+ Photo Luminescence Spectroscopy to Distinguish the Effect of Uniaxial Stress from Cooling Rate on Soda-Lime Silicate Glass

Evolution of spectroscopic properties of a soda–lime silicate glass with different thermal history and under applied uniaxial stress was investigated using Raman and Brillouin spectroscopies as well as Nd³⁺ photoluminescence techniques. Samples of soda–lime silicate with a cooling rate from 6 × 10⁻⁴ to 650 K/min were prepared either by controlled cooling from the melt using a differential scanning calorimeter or by a conventional annealing procedure. Uniaxial stress effects in a range from 0 to −1.3 GPa were investigated in situ by compression of the glass cylinders. The spectroscopic observations of rearrangements in the network structure were related to the set cooling rates or the applied uniaxial stress to calculate an interrelated set of calibrations. Comparing the results from Raman and Brillouin spectroscopy with Nd³⁺ photoluminescence analysis, we find a linear dependence that can be used to identify uniaxial stress and cooling rate in any given combination concurrently. The interrelated calibrations and linear dependence models are established and evaluated, and equations relating the change of glass network due to effects of cooling rate or uniaxial stress are given.

Utilizing Rare-Earth-Elements Luminescence and Vibrational-Spectroscopies to Follow High Pressure Densification of Soda-Lime Glass

A new series of soda–lime glass naturally doped with Nd and doped with 0.2 wt% of Eu₂O₃ was densified in a multi-anvil press up to 21 GPa. The densities of the millimetric samples were precisely measured using a floatation method in a heavy liquid made with sodium polytungstate. The obtained densification curve is significantly different from the calibration previously reported, reaching a maximum densification saturation of 3.55 ± 0.14%. This difference could be due to better hydrostatic conditions realized in this new study. The densified samples were characterized using Raman and Brillouin spectroscopy, as well as the emission of both Eu³⁺ and Nd³⁺. The evolution of the spectra was evaluated using integration methods to reduce error bars. The relative precision of the calibration curves is discussed. The evolution of Nd³⁺ transition was found to be the most sensitive calibration. Linear dependence with the density was found for all observables, with exception for Brillouin spectroscopy showing a divergent behavior. The Brillouin shift shows an unreported minimum for a densification ~0.4%.

SiO2-Based Nanostructured Superhydrophobic Film with High Optical Transmittance

Superhydrophobic and transparent films would be very useful in optoelectronic applications where non-wetting is desired. Herein, hexamethyldisilazane was used for functionalization of fumed SiO2 nanoparticles via silylation derivatization reaction. Modified fumed SiO2 nanoparticle dispersion was used for fabrication of SiO2-based nanostructured film via drop-casting method. This film exhibited a combination of high optical transmittance in the visible spectrum portion and superhydrophobicity (163° ± 1° and hysteresis as low as ~2°). This was possible to achieve due to the submicrometer-scale roughness (Rq = 252.7 nm) and branched network structure of the film surface with convenient surface chemistry of hydrophobic methyl groups. The method reported herein is not complicated, allows for obtaining large quantities of modified SiO2 nanoparticle dispersions and can be used in combination with other deposition methods.

Friction and Wear Properties of Ni3Si Alloy with Ti Addition at High Temperatures

The tribological properties of Ni₃Si alloy were studied at high temperatures. The effect of the addition of Ti was also analyzed. The surface composition was analyzed by Raman spectroscopy. The results showed that the friction coefficient decreased with the increasing temperature, and the wear rate changed slightly from 25 to 400 °C. However, the wear resistance of the alloys decreased sharply at 600 °C, and this was due to the decrease of the high-temperature strength and the severe oxidation of the alloys. Although the oxidation resistance of Ni₃Si alloy decreased with Ti addition, the tribological property was improved by the addition of Ti. The Ni₃Si alloy with 5% Ti addition had the best wear resistance at high temperatures as compared to pure Ni₃Si alloy and with 10% Ti addition, and the wear rates of the alloys were in the order of magnitude of 10^-5 mm³/Nm. With the increase of temperature, the wear mechanism of pure Ni₃Si alloy transformed from abrasive wear to oxidation wear. As the Ti content increased, the wear mechanisms of the alloys changed from abrasive wear to fatigue wear at low temperature, and oxidation wear and fatigue wear at high temperature.

In-situ Raman spectroscopic measurements of the deformation region in indented glasses

This paper describes the design and integration of a custom-built optical instrument for in-situ Raman microscopy suitable for collecting high-quality spectroscopic data during the indentation of glass materials. It will further show that the reported experimental setup enables meaningful in-situ spectroscopic observations during indentation of fused silica at forces in the millinewton range. The aim of the paper is to demonstrate the vital importance of matching the analysis volume of the Raman microscope with the indentation-induced deformation volume to capture the full extent of the related spectral alterations by minimizing spectral contributions from the unperturbed bulk material (in-situ and ex-situ) and indenter probe (in-situ only). In this context, the paper will also touch upon possible pitfalls in ex-situ and in-situ Raman measurements on indented glasses in cases where the analysis and deformation volumes are not well matched and describe the misinterpretations that may result.

Waste Windshield-Derived Silicon/Carbon Nanocomposites as High-Performance Lithium-Ion Battery Anodes

Silicon has emerged as the most promising high-capacity material for lithium-ion batteries. Waste glass can be a potential low cost and environmentally benign silica resource enabling production of nanosized silicon at the industry level. Windshields are generally made of laminated glass comprising two separate glass bonded together with a layer of polyvinyl butyral sandwiched between them. Herein, silicon/carbon nanocomposites are fabricated from windshields for the first time via magnesiothermic reduction and facile carbonization process using both waste glass and polyvinyl butyral as silica and carbon sources, respectively. High purity reduced silicon has unique 3-dimensional nanostructure with large surface area. Furthermore, the incorporation of carbon in silicon enable to retain the composite anodes highly conductive and mechanically robust, thus providing enhanced cycle stability.

Effect of composition and pressure on the shear strength of sodium silicate glasses: An atomic scale simulation study

The elastoplastic behavior of sodium silicate glasses is studied at different scales as a function of composition and pressure, with the help of quasistatic atomistic simulations. The samples are first compressed and then sheared at constant pressure to calculate yield strength and permanent plastic deformations. Changes occurring in the global response are then compared to the analysis of local plastic rearrangements and strain heterogeneities. It is shown that the plastic response results from the succession of well-identified localized irreversible deformations occurring in a nanometer-size area. The size and the number of these local rearrangements, as well as the amount of internal deviatoric and volumetric plastic deformation, are sensitive to the composition and to the pressure. In the early stages of the deformation, plastic rearrangements are driven by sodium mobility. Consequently, the elastic yield strength decreases when the sodium content increases, and the same when pressure increases. Finally, good correlation was found between global and local stress-strain relationships, reinforcing again the role of sodium ions as local initiators of the plastic behavior observed at larger scales.

In situ structural analysis of calcium aluminosilicate glasses under high pressure

In situ micro-Raman spectroscopy was used to investigate the structural evolution of OH(-)-free calcium aluminosilicate glasses, under high pressure and at room temperature. Evaluation was made of the role of the SiO2 concentration in percalcic join systems, for Al/(Al  +  Si) in the approximate range from 0.9 to 0.2. Under high pressure, the intensity of the main band related to the bending mode of bridging oxygen ([Formula: see text][T-O-T], where T  =  Si or Al) decreased gradually, suggesting that the bonds were severely altered or even destroyed. In Si-rich glasses, compression induced a transformation of Q (n) species to Q (n-1). In the case of Al-rich glass, the Al in the smallest Q (n) units evolved from tetrahedral to higher-coordinated Al (([5])Al and ([6])Al). Permanent structural changes were observed in samples recovered from the highest pressure of around 15 GPa and, particularly for Si-rich samples, the recovered structure showed an increase of three-membered rings in the Si/Al tetrahedral network.

A-thermal elastic behavior of silicate glasses

Depending on the composition of silicate glasses, their elastic moduli can increase or decrease as function of the temperature. Studying the Brillouin frequency shift of these glasses versus temperature allows the a-thermal composition corresponding to an intermediate glass to be determined. In an intermediate glass, the elastic moduli are independent of the temperature over a large temperature range. For sodium alumino-silicate glasses, the a-thermal composition is close to the albite glass (NaAlSi3O8). The structural origin of this property is studied by in situ high temperature Raman scattering. The structure of the intermediate albite glass and of silica are compared at different temperatures between room temperature and 600 °C. When the temperature increases, it is shown that the high frequency shift of the main band at 440 cm(-1) in silica is a consequence of the cristobalite-like alpha-beta transformation of 6-membered rings. This effect is stronger in silica than bond elongation (anharmonic effects). As a consequence, the elastic moduli of silica increase as the temperature increases. In the albite glass, the substitution of 25% of Si(4+) ions by Al(3+) and Na(+) ions decreases the proportion of SiO2 6-membered rings responsible for the silica anomaly. The effects of the silica anomaly balance the anharmonicity in albite glass and give rise to an intermediate a-thermal glass. Different networks, formers or modifiers, can be added to produce different a-thermal glasses with useful mechanical or chemical properties.

Driving force for indentation cracking in glass: composition, pressure and temperature dependence

The occurrence of damage at the surface of glass parts caused by sharp contact loading is a major issue for glass makers, suppliers and end-users. Yet, it is still a poorly understood problem from the viewpoints both of glass science and solid mechanics. Different microcracking patterns are observed at indentation sites depending on the glass composition and indentation cracks may form during both the loading and the unloading stages. Besides, we do not know much about the fracture toughness of glass and its composition dependence, so that setting a criterion for crack initiation and predicting the extent of the damage yet remain out of reach. In this study, by comparison of the behaviour of glasses from very different chemical systems and by identifying experimentally the individual contributions of the different rheological processes leading to the formation of the imprint--namely elasticity, densification and shear flow--we obtain a fairly straightforward prediction of the type and extent of the microcracks which will most likely form, depending on the physical properties of the glass. Finally, some guidelines to reduce the driving force for microcracking are proposed in the light of the effects of composition, temperature and pressure, and the areas for further research are briefly discussed.

Elastic moduli of permanently densified silica glasses

Modelling the mechanical response of silica glass is still challenging, due to the lack of knowledge concerning the elastic properties of intermediate states of densification. An extensive Brillouin Light Scattering study on permanently densified silica glasses after cold compression in diamond anvil cell has been carried out, in order to deduce the elastic properties of such glasses and to provide new insights concerning the densification process. From sound velocity measurements, we derive phenomenological laws linking the elastic moduli of silica glass as a function of its densification ratio. The found elastic moduli are in excellent agreement with the sparse data extracted from literature, and we show that they do not depend on the thermodynamic path taken during densification (room temperature or heating). We also demonstrate that the longitudinal sound velocity exhibits an anomalous behavior, displaying a minimum for a densification ratio of 5%, and highlight the fact that this anomaly has to be distinguished from the compressibility anomaly of a-SiO₂ in the elastic domain.