Metal artifacts in computed tomography for radiation therapy planning: dosimetric effects and impact of metal artifact reduction

Use of Carbon Fiber Implants to Improve the Safety and Efficacy of Radiation Therapy for Spine Tumor Patients

Current standard of care treatment for patients with spine tumors includes multidisciplinary approaches, including the following: (1) surgical tumor debulking, epidural spinal cord decompression, and spine stabilization techniques; (2) systemic chemo/targeted therapies; (3) radiation therapy; and (4) surveillance imaging for local disease control and recurrence. Titanium pedicle screw and rod fixation have become commonplace in the spine surgeon's armamentarium for the stabilization of the spine following tumor resection and separation surgery. However, the high degree of imaging artifacts seen with titanium implants on postoperative CT and MRI scans can significantly hinder the accurate delineation of vertebral anatomy and adjacent neurovascular structures to allow for the safe and effective planning of downstream radiation therapies and detection of disease recurrence. Carbon fiber-reinforced polyetheretherketone (CFR-PEEK) spine implants have emerged as a promising alternative to titanium due to the lack of artifact signals on CT and MRI, allowing for more accurate and safe postoperative radiation planning. In this article, we review the tenants of the surgical and radiation management of spine tumors and discuss the safety, efficacy, and current limitations of CFR-PEEK spine implants in the multidisciplinary management of spine oncology patients.

Radiation Treatment Planning After Minimum Metallic Instrumentation for Patients with Spinal Metastases: A Case Series

Background and Objectives: The utilization of non-metallic pedicle screws and rods has become a favored approach in the management of spinal tumors. An abundance of metal artifacts improves postoperative imaging and allows for precise radiation treatment planning. Under certain conditions, a vertebral body replacement (VBR) is necessary in addition to dorsal fixation. For a long time, VBR hardware was available as titanium implants only. Recently, other non-titanium products were introduced into the market. This study compares radiotherapy planning after VBR with titanium and non-titanium materials. Materials and Methods: This is a retrospective cohort study in a single academic center setting. VBR was performed for thoracic spinal metastatic disease. Radiation plan quality was evaluated according to the criteria of the International Commission on Radiation Units and Measurements, based on postoperative CT imaging. Results: Six patients with dorsal fixation and VBR were included, half of which were treated with titanium VBR and the other half with a minimum metallic implant. In addition, patients received different dorsal fixation hardware. No difference was found in terms of radiation plan quality. With non-titanium materials, visual demarcation during radiation planning was superior. Conclusions: This is the first study in the field to comprehensively compare radiation treatment planning after VBR using different materials. With minimum metallic implants, radiotherapy planning is equal in terms of planning but superior in terms of visual demarcation in comparison to standard titanium VBR, potentially enabling more precise radiotherapy approaches.

4DCT image artifact detection using deep learning

BACKGROUND

Four-dimensional computed tomography (4DCT) is an es sential tool in radiation therapy. However, the 4D acquisition process may cause motion artifacts which can obscure anatomy and distort functional measurements from CT scans.

PURPOSE

We describe a deep learning algorithm to identify the location of artifacts within 4DCT images. Our method is flexible enough to handle different types of artifacts, including duplication, misalignment, truncation, and interpolation.

METHODS

We trained and validated a U-net convolutional neural network artifact detection model on more than 23 000 coronal slices extracted from 98 4DCT scans. The receiver operating characteristic (ROC) curve and precision-recall curve were used to evaluate the model's performance at identifying artifacts compared to a manually identified ground truth. The model was adjusted so that the sensitivity in identifying artifacts was equivalent to that of a human observer, as measured by computing the average ratio of artifact volume to lung volume in a given scan.

RESULTS

The model achieved a sensitivity, specificity, and precision of 0.78, 0.99, and 0.58, respectively. The ROC area-under-the-curve (AUC) was 0.99 and the precision-recall AUC was 0.73. Our model sensitivity is 8% higher than previously reported state-of-the-art artifact detection methods.

CONCLUSIONS

The model developed in this study is versatile, designed to handle duplication, misalignment, truncation, and interpolation artifacts within a single image, unlike earlier models that were designed for a single artifact type.

Evaluation of a Metal Artifact Reduction Algorithm for Image Reconstruction on a Novel CBCT Platform

PURPOSE

The presence of metal implants can produce artifacts and distort Hounsfield units (HU) in patient computed tomography (CT) images. The purpose of this work was to characterize a novel metal artifact reduction (MAR) algorithm for reconstruction of CBCT images obtained by the HyperSight imaging system.

METHODS

Three tissue-equivalent phantoms were fitted with materials commonly used in medical applications. The first consisted of a variety of metal samples centered within a solid water block, the second was an Advanced Electron Density phantom with metal rods, and the third consisted of hip prostheses positioned within a water tank. CBCT images of all phantoms were acquired and reconstructed using the MAR and iCBCT Acuros algorithms on the HyperSight system. The signal-to-noise ratio (SNR), artifact index (AI), structural similarity index measure (SSIM), peak signal-to-noise ratio (PSNR), and mean-square error (MSE) were computed to assess the image quality in comparison to artifact-free reference images. The mean HU at various VOI positions around the cavity was calculated to evaluate the artifact dependence on distance and angle from the center of the cavity. The artifact volume of the phantom (excluding the cavity) was estimated by summing the volume of all voxels with HU values outside the 5th and 95th percentiles of the phantom CBCT with no artifact.

RESULTS

The SNR, AI, SSIM, PSNR, and MSE metrics demonstrated significantly higher similarity to baseline when using MAR compared to iCBCT Acuros for all high-density materials, except for aluminum. Mean HU returned to expected solid water background at a shorter distance from metal sample in the MAR images, and the standard deviation remained lower for the MAR images at all distances from the insert. The artifact volume decreased using the novel MAR algorithm for all metal samples excluding aluminum (p < 0.001) and all hip prostheses (p < 0.05).

CONCLUSION

Varian's HyperSight MAR reconstruction algorithm shows a reduction in metal artifact metrics, motivating the use of MAR reconstruction for patients with metal implants.

The impact of metal implants on the dose and clinical outcome of radiotherapy (Review)

Radiotherapy (RT) is one of the most widely used and effective cancer treatments. With the increasing need for organ reconstruction and advancements in material technology, an increasing number of patients with cancer have metallic implants. These implants can affect RT dosage and clinical outcomes, warranting careful consideration by oncologists. The present review discussed the mechanisms by which different types of metallic implants impact various stages of the RT process, examined methods to mitigate these effects during treatment, and discussed the clinical implications of metallic implants on RT outcomes. In summary, when metallic implants are present within the RT field, oncologists should carefully assess their impact on the treatment.

A Denoising Diffusion Probabilistic Model for Metal Artifact Reduction in CT

The presence of metal objects leads to corrupted CT projection measurements, resulting in metal artifacts in the reconstructed CT images. AI promises to offer improved solutions to estimate missing sinogram data for metal artifact reduction (MAR), as previously shown with convolutional neural networks (CNNs) and generative adversarial networks (GANs). Recently, denoising diffusion probabilistic models (DDPM) have shown great promise in image generation tasks, potentially outperforming GANs. In this study, a DDPM-based approach is proposed for inpainting of missing sinogram data for improved MAR. The proposed model is unconditionally trained, free from information on metal objects, which can potentially enhance its generalization capabilities across different types of metal implants compared to conditionally trained approaches. The performance of the proposed technique was evaluated and compared to the state-of-the-art normalized MAR (NMAR) approach as well as to CNN-based and GAN-based MAR approaches. The DDPM-based approach provided significantly higher SSIM and PSNR, as compared to NMAR (SSIM: p [Formula: see text]; PSNR: p [Formula: see text]), the CNN (SSIM: p [Formula: see text]; PSNR: p [Formula: see text]) and the GAN (SSIM: p [Formula: see text]; PSNR: p <0.05) methods. The DDPM-MAR technique was further evaluated based on clinically relevant image quality metrics on clinical CT images with virtually introduced metal objects and metal artifacts, demonstrating superior quality relative to the other three models. In general, the AI-based techniques showed improved MAR performance compared to the non-AI-based NMAR approach. The proposed methodology shows promise in enhancing the effectiveness of MAR, and therefore improving the diagnostic accuracy of CT.

Linac- and CyberKnife-based MRI-only treatment planning of prostate SBRT using an optimized synthetic CT calibration curve

PURPOSE

CT Hounsfield Units (HUs) are converted to electron density using a calibration curve obtained from physical measurements of an electron density phantom. HU values assigned to an MRI-derived synthetic computed tomography (sCT) may present a different relationship with electron density compared to CT HU. Correct assignment of sCT HU values is critical for accurate dose calculation and delivery. The goals of this work were to develop a sCT calibration curve using patient data acquired on a clinically commissioned CT scanner and assess for CyberKnife- and volumetric modulated arc therapy (VMAT)-based MR-only treatment planning of prostate SBRT.

METHODS

Same-day CT and MRI simulation in the treatment position were performed on 10 patients treated with SBRT to the prostate. Dixon in-phase and out-of-phase MRIs were acquired on a 3T scanner using a 3D T1-weighted gradient-echo sequence to generate sCTs using a commercial sCT algorithm. CT and sCT datasets were co-registered and HU values compared using mean absolute error (MAE). An optimized HU-to-density calibration curve was created based on average HU values across an institutional patient database for each of the four sCT tissue types. Clinical CyberKnife and VMAT treatment plans were generated on each patient CT and recomputed onto corresponding sCTs. Dose distributions computed using CT and sCT were compared using gamma criteria and dose-volume-histograms.

RESULTS

For the optimized calibration curve, HU values were -96, 37, 204, and 1170 and relative electron densities were 0.95, 1.04, 1.1, and 1.7 for adipose, soft tissue, inner bone, and outer bone, respectively. The proposed sCT protocol produced total MAE of 94 ± 20HU. Gamma values mean ± std (min-max) were 98.9% ± 0.9% (97.1%-100%) and 97.7% ± 1.3% (95.3%-99.3%) for VMAT and CyberKnife plans, respectively.

CONCLUSION

MRI-derived sCT using the proposed approach shows excellent dosimetric agreement with conventional CT simulation, demonstrating the feasibility of MRI-derived sCT for prostate SBRT treatment planning.

Stereotactic Body Radiation Therapy (SBRT) in prostate cancer in the presence of hip prosthesis - is it a contraindication? A narrative review

Hip replacement is a common orthopedic surgery in the aging population. With the rising incidence of prostate cancer, metallic hip prosthetics can cause considerable beam hardening and streak artifacts, leading to difficulty in identifying the target volumes and planning process for radiation treatment. The growing use of Stereotactic Body Radiation Therapy (SBRT) to treat prostate cancer is now well established. However, the use of this treatment modality in the presence of a hip prosthesis is poorly understood. There is enough literature on planning for external beam radiation treatment without any difficulties in the presence of hip prosthesis with conventional or Hypofractionated treatment. However, there is a shortage of literature on the impact of the prosthesis in SBRT planning, and there is a need for further understanding and measures to mitigate the obstacles in planning for SBRT in the presence of hip prosthesis. We present our review of the intricacies that need to be understood while considering SBRT in the presence of hip prostheses in prostate cancer treatment.

PND-Net: Physics-Inspired Non-Local Dual-Domain Network for Metal Artifact Reduction

Metal artifacts caused by the presence of metallic implants tremendously degrade the quality of reconstructed computed tomography (CT) images and therefore affect the clinical diagnosis or reduce the accuracy of organ delineation and dose calculation in radiotherapy. Although various deep learning methods have been proposed for metal artifact reduction (MAR), most of them aim to restore the corrupted sinogram within the metal trace, which removes beam hardening artifacts but ignores other components of metal artifacts. In this paper, based on the physical property of metal artifacts which is verified via Monte Carlo (MC) simulation, we propose a novel physics-inspired non-local dual-domain network (PND-Net) for MAR in CT imaging. Specifically, we design a novel non-local sinogram decomposition network (NSD-Net) to acquire the weighted artifact component and develop an image restoration network (IR-Net) to reduce the residual and secondary artifacts in the image domain. To facilitate the generalization and robustness of our method on clinical CT images, we employ a trainable fusion network (F-Net) in the artifact synthesis path to achieve unpaired learning. Furthermore, we design an internal consistency loss to ensure the data fidelity of anatomical structures in the image domain and introduce the linear interpolation sinogram as prior knowledge to guide sinogram decomposition. NSD-Net, IR-Net, and F-Net are jointly trained so that they can benefit from one another. Extensive experiments on simulation and clinical data demonstrate that our method outperforms state-of-the-art MAR methods.

Stereotactic Body Radiation Therapy for Clinically Localized Prostate Cancer in Men With Hip Prostheses: A Cautionary Note

PURPOSE

Stereotactic body radiation therapy (SBRT) has been established as a safe and effective treatment for prostate cancer. SBRT requires high accuracy to reduce treatment margins. Metal hip prostheses create artifacts that distort pelvic imaging and potentially decrease the accuracy of target/organ at risk (OAR) identification and radiation dose calculations. Data on the safety and efficacy of SBRT after hip replacement is limited. This single-institution study sought to evaluate the safety and local control following SBRT for prostate cancer in men with hip replacements.

METHODS

23 patients treated with localized prostate cancer and a history of pre-treatment hip replacement, treated with SBRT from 2007 to 2017 at MedStar Georgetown University Hospital were included in this retrospective analysis. Treatment was administered with the CyberKnife® (Accuray Incorporated, Sunnyvale, CA) at doses of 35 Gy or 36.25 Gy in 5 fractions. The targets and OARs were identified and contoured by a single experienced Radiation Oncologist (SPC). The adequacy of the CT and T2W MRI images for treatment planning was assessed with a three-point scale (good, adequate, or suboptimal). During treatment planning, care was taken to avoid treatment beams that directly traversed the hip prosthesis. Toxicities were recorded and scored using the Common Terminology Criteria for Adverse Events version 4.0 (CTCAE v.4.0). Local recurrence was confirmed by magnetic resonance imaging and/or prostate biopsy.

RESULTS

The median follow-up was seven years. The patients were elderly (median age = 71 years) with a high rate of comorbidities (Charlson Comorbidity Index > 2 in 25%). Four patients had bilateral hip replacements. The majority of patients were low to intermediate risk per the D'Amico classification. Around 13% received upfront ADT. In total, 13 patients were treated with 35 Gy, and 10 were treated with 36.25 Gy. The rates of late > Grade 3 GU toxicity and > Grade 2 GI toxicity were 8.6% and 4.3%, respectively. There were no Grade 4 or 5 toxicities. Six patients (26%) developed a local recurrence at a median time of 7.5 years. Of these six patients, four had unilateral hip replacements and two had bilateral. Three underwent salvage cryotherapy and three received salvage ADT.

CONCLUSIONS

 In the general population, high-grade toxicities and local recurrences are uncommon following prostate SBRT. However, in this cohort of patients with prior hip replacements, prostate SBRT had higher than expected rates of late toxicity and local recurrence. In the opinion of the authors, such patients should be counseled regarding an elevated risk of late toxicity and local recurrence with prostate SBRT. With its ultrasound guidance, brachytherapy would have the advantage of circumventing the need for MRI/CT-based imaging and thus may represent a preferable radiation alternative in this patient population. If these patients are treated with SBRT, they should be monitored closely for local recurrence so early salvage can be performed. We hope that recent advances in metal artifact reduction techniques and dose-calculation algorithms will improve future outcomes.

Evaluation of the Treatment Planning and Delivery for Hip Implant Cases on Tomotherapy

Purpose

The metal present in the implant creates artifacts during the treatment simulation, which impacts the treatment planning and delivery of the prescribed dose to the target and sparing normal tissues. This retrospective study evaluated the uncertainties in the planning and delivery of doses for prosthesis cases with dedicated phantom.

Materials and Methods

In this retrospective study, 11 patients with a hip prosthesis having cervix carcinoma were selected. Two treatment plans were generated on treatment planning system (TPS) for each case. Plan_No_Res was without any beam restriction, and Plan_exit_only was the plan with restricted beam entry through the metallic implant. An indigenous phantom was utilized to verify the accuracy of the treatment. In the phantom, some groves were present, which could be filled by implants that mimic the patient's geometries, like left, right and bilateral femur implants. The delivered doses were recorded using optically stimulated luminescence dosimeters (OSLDs), which were placed at different positions in the phantom. The plans were further calculated using megavoltage computed tomography (MVCT) scans acquired during treatment.

Results

The patient data showed no significant dose changes between the two planning methods. The treatment time increases from 412.18 ± 86.65 to 427.36 ± 104.80 with P = 0.03 for Plan_No_Res and Plan_exit_only, respectively. The difference between planned and delivered doses of various points across phantom geometries was within ± 9.5% in each case as left, right, and bilateral implant. The variations between OSLDs and MVCT calculated doses were also within ± 10.8%.

Conclusion

The study showed the competency of tomotherapy planning for hip prosthesis cases. The phantom measurements demonstrate the errors in dosimetry near the implant material, suggesting the need for precise methods to deal with artifact-related issues.

Geometric distortion caused by metallic femoral head prosthesis in prostate cancer imaging on an MR Linac: in-vivo measurements of spatial deformation

OBJECTIVES

Metallic implants cause artefacts and distortion on MRI. To ensure accurate dose delivery and plan adaptation on an MR Linac, there is a need to evaluate distortion caused.

METHODS

Participants were imaged on an MR Linac (Elekta Unity, Elekta AB Stockholm). Three sequences were evaluated. Two vendor supplied (T2W TSE 3D), and one T2W TSE 3D optimized to reduce metal artefact distortions. Images were rigidly registered to CT images by a single observer, using bony anatomy. Three coronal and three axial images were selected, and six paired, adjacent, bony landmarks were identified on each slice. Images bisecting treatment isocentre were included. Difference between landmark coordinates was taken to be measure of distortion.

RESULTS

Five observers participated. Thirty six pairs of bony landmarks were identified. Median difference in position of landmarks was ≤3 mm (range 0.3-4.4 mm). One-way analysis of variance (ANOVA) between observer means showed no significant variation between sequences or patients (P = 1.26 in plane, P = 0.11 through plane). Interobserver intra class correlation (ICC) was 0.70 in-plane and 0.78 through-plane. Intra-observer ICC for three observers was 0.76, 0.81, 0.83, showing moderate to good reliability on this small cohort.

CONCLUSIONS

This in-vivo feasibility study suggests distortion due to metallic hip prosthesis is not an obstacle for pelvic radiotherapy on an MR Linac. Research on the impact on plan quality is warranted.

ADVANCES IN KNOWLEDGE

This work supports feasibility of treating patients with metallic hip prosthesis on an MR Linac.

Quantification of MRI Artifacts in Carbon Fiber Reinforced Polyetheretherketone Thoracolumbar Pedicle Screw Constructs prior to Spinal Stereotactic Radiosurgery

PURPOSE

Carbon fiber reinforced polyetheretherketone (CFRP) is a nonmetallic material that is a subject of growing interest in the field of spinal instrumentation manufacturing. The radiolucency and low magnetic susceptibility of CFRP has potential to create less interference with diagnostic imaging compared with titanium implants. However, an objective comparison of the image artifact produced by titanium and CFRP implants has not been described. Spinal oncology, particularly after resection of spinal tumors and at the time of spinal stereotactic radiosurgery planning, relies heavily on imaging interpretation for evaluating resection, adjuvant treatment planning, and surveillance. We present a study comparing measurements of postoperative magnetic resonance imaging artifacts between titanium and CFRP pedicle screw constructs in the setting of separation surgery for metastatic disease.

METHODS AND MATERIALS

The diameter of the signal drop around the screws (pedicle screw artifact) and the diameter of the spinal canal free from artifacts (canal visualization) were measured in consecutive patients who had spinal instrumentation followed by spinal stereotactic radiosurgery in the June 2019 to May 2022 timeframe. The spinal cord presented a shift at the screw level in sagittal images which was also measured (Sagittal Distortion, SagD).

RESULTS

Fifty patients, corresponding to 356 screws and 183 vertebral levels, were evaluated overall. CFRP produced less artifacts in all the 3 parameters compared with titanium: mean pedicle screw artifact (CFRP = 5.8 mm, Ti = 13.2 mm), canal visualization (CFRP = 19.2 mm, Ti = 15.5 mm), and SagD (CFRP = .5 mm, Ti = 1.9 mm), all P < .001. In practice, these findings translate into better-quality magnetic resonance imaging.

CONCLUSIONS

The initial perceived advantages are easier evaluation of postoperative imaging, facilitating radiation treatment planning, recurrence detection, and avoidance in repeating a suboptimal computed tomography myelogram. Further clinical studies analyzing long-term outcomes of patients treated with CFRP implants are necessary.

PTCOG Gastrointestinal Subcommittee Lower Gastrointestinal Tract Malignancies Consensus Statement

Purpose

Radiotherapy delivery in the definitive management of lower gastrointestinal (LGI) tract malignancies is associated with substantial risk of acute and late gastrointestinal (GI), genitourinary, dermatologic, and hematologic toxicities. Advanced radiation therapy techniques such as proton beam therapy (PBT) offer optimal dosimetric sparing of critical organs at risk, achieving a more favorable therapeutic ratio compared with photon therapy.

Materials and Methods

The international Particle Therapy Cooperative Group GI Subcommittee conducted a systematic literature review, from which consensus recommendations were developed on the application of PBT for LGI malignancies.

Results

Eleven recommendations on clinical indications for which PBT should be considered are presented with supporting literature, and each recommendation was assessed for level of evidence and strength of recommendation. Detailed technical guidelines pertaining to simulation, treatment planning and delivery, and image guidance are also provided.

Conclusion

PBT may be of significant value in select patients with LGI malignancies. Additional clinical data are needed to further elucidate the potential benefits of PBT for patients with anal cancer and rectal cancer.

Stereotactic Body Radiation Therapy: A Radiosurgery Society Guide to the Treatment of Localized Prostate Cancer Illustrated by Challenging Cases

Traditionally, external beam radiotherapy (EBRT) for localized prostate cancer (PCa) involved lengthy courses with low daily doses. However, advancements in radiation delivery and a better understanding of prostate radiobiology have enabled the development of shorter courses of EBRT. Ultrahypofractionated radiotherapy, administering doses greater than 5 Gy per fraction, is now considered a standard of care regimen for localized PCa, particularly for intermediate-risk disease. Stereotactic body radiotherapy (SBRT), a specific type of ultrahypofractionated radiotherapy employing advanced planning, imaging, and treatment technology to deliver in five or fewer fractions, is gaining prominence as a cost-effective, convenient, and safe alternative to longer radiotherapy courses. It is crucial to address practical considerations related to patient selection, fractionation scheme, target delineation, and planning objectives. This is especially important in challenging clinical situations where clear evidence for guidance may be lacking. The Radiosurgery Society endorses this case-based guide with the aim of providing a practical framework for delivering SBRT to the intact prostate, exemplified by two case studies. The article will explore common SBRT dose/fractionation schemes and dose constraints for organs-at-risk. Additionally, it will review existing evidence and expert opinions on topics such as SBRT dose escalation, the use of rectal spacers, the role of androgen deprivation therapy in the context of SBRT, SBRT in special patient populations (e.g., high-risk disease, large prostate, high baseline urinary symptom burdens, and inflammatory bowel disease), as well as new imaging-guidance techniques like Magnetic Resonance Imaging for SBRT delivery.

Effects of modern aesthetic dental fillings on proton therapy

Background and purpose

High-density dental fillings pose a non-negligible impact on head and neck cancer treatment. For proton therapy, stopping power ratio (SPR) prediction will be significantly impaired by the associated image artifacts. Dose perturbation is also inevitable, compromising the treatment plan quality. While plenty of work has been done on metal or amalgam fillings, none has touched on composite resin (CR) and glass ionomer cement (GIC) which have seen an increasing usage. Hence, this work aims to provide a detailed characterisation of SPR and dose perturbation in proton therapy caused by CR and GIC.

Materials and methods

Four types of fillings were used: CR, Fuji Bulk (FB), Fuji II (FII) and Fuji IX (FIX). The latter three belong to GIC category. Measured SPR were compared with SPR predicted using single-energy computed tomography (SECT) and dual-energy computed tomography (DECT). Dose perturbation of proton beams with lower- and higher-energy levels was also quantified using Gafchromic films.

Results

The measured SPR for CR, FB, FII and FIX were 1.68, 1.77, 1.77 and 1.76, respectively. Overall, DECT could predict SPR better than SECT. The lowest percentage error achieved by DECT was 19.7 %, demonstrating the challenge in estimating SPR, even for fillings with relatively lower densities. For both proton beam energies and all four fillings of about 4.5 mm thickness, the maximum dose perturbation was 3 %.

Conclusion

This study showed that dose perturbation by CR and GIC was comparatively small. We have measured and recommended the SPR values for overriding the fillings in TPS.

Iterative Metal Artifact Reduction in Head and Neck CT Facilitates Tumor Visualization of Oral and Oropharyngeal Cancer Obscured by Artifacts From Dental Hardware

RATIONALE AND OBJECTIVES

The purpose of this study was to evaluate the diagnostic utility of iterative metal artifact reduction (iMAR) in computed tomography (CT)-imaging of oral and oropharyngeal cancers when obscured by dental hardware artifacts and to determine the most appropriate iMAR settings for this purpose.

MATERIALS AND METHODS

The study retrospectively enrolled 27 patients (8 female, 19 male; mean age 64±12.7years) with histologically confirmed oral or oropharyngeal cancer obscured by dental artifacts in contrast-enhanced CT. Raw CT data were reconstructed with ascending iMAR strengths (levels 1/2/3/4/5) and one reconstruction without iMAR (level 0). For subjective analysis, two blinded radiologists rated tumor visualization and artifact severity on a five-point Likert scale. For objective analysis, signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR), and artifact index (AI) were determined.

RESULTS

iMAR reconstructions improved the subjective image quality of tumor edge and contrast, and the objective parameters of tumor SNR and CNR, reaching their optimum at iMAR levels 4 and 5 (P<.001). AI decreased with iMAR reconstructions reaching its minimum at iMAR level 5 (P<.001). Tumor detection rates increased 2.4-fold with iMAR 5, 2.1-fold with iMAR 4, and 1.9-fold with iMAR 3 compared to reconstructions without iMAR. Disadvantages such as algorithm-induced artifacts increased significantly with higher iMAR strengths (P<.05), reaching a maximum with iMAR 5.

CONCLUSION

iMAR significantly improves CT imaging of oral and oropharyngeal cancers, as confirmed by both subjective and objective measures, with best results at highest iMAR strengths.

Evaluation of computed tomography metal artifact and CyberKnife fiducial recognition for novel size fiducial markers

PURPOSE

This study aimed to compare fiducial markers used in CyberKnife treatment in terms of metal artifact intensity observed in CT images and fiducial recognition in the CyberKnife system affected by patient body thickness and type of marker.

METHODS

Five markers, ACCULOC 0.9 mm × 3 mm, Ball type Gold Anchor (GA) 0.28 mm × 10 mm, 0.28 mm × 20 mm, and novel size GA 0.4 mm × 10 mm, 0.4 mm × 20 mm were evaluated. To evaluate metal artifacts of CT images, two types of CT images of water-equivalent gels with each marker were acquired using Aquilion LB CT scanner, one applied SEMAR (SEMAR-on) and the other did not apply this technique (SEMAR-off). The evaluation metric of artifact intensity (MSD ) which represents a variation of CT values were compared for each marker. Next, 5, 15, and 20 cm thickness of Tough Water (TW) was placed on the gel under the condition of overlapping the vertebral phantom in the Target Locating System, and the live image of each marker was acquired to compare fiducial recognition.

RESULTS

The mean MSD of SEMAR-off was 78.80, 74.50, 97.25, 83.29, and 149.64 HU for ACCULOC, GA0.28 mm × 10 mm, 20 mm, and 0.40 mm × 10 mm, 20 mm, respectively. In the same manner, that of SEMAR-on was 23.52, 20.26, 26.76, 24.89, and 33.96 HU, respectively. Fiducial recognition decreased in the order of 5, 15, and 20 cm thickness, and GA 0.4 × 20 mm showed the best recognition at thickness of 20 cm TW.

CONCLUSIONS

We demonstrated the potential to reduce metal artifacts in the CT image to the same level for all the markers we evaluated by applying SEMAR. Additionally, the fiducial recognition of each marker may vary depending on the thickness of the patient's body. Particularly, we showed that GA 0.40 × 20 mm may have more optimal recognition for CyberKnife treatment in cases of high bodily thickness in comparison to the other markers.

Deep learning-based ultrasound transducer induced CT metal artifact reduction using generative adversarial networks for ultrasound-guided cardiac radioablation

In US-guided cardiac radioablation, a possible workflow includes simultaneous US and planning CT acquisitions, which can result in US transducer-induced metal artifacts on the planning CT scans. To reduce the impact of these artifacts, a metal artifact reduction (MAR) algorithm has been developed based on a deep learning Generative Adversarial Network called Cycle-MAR, and compared with iMAR (Siemens), O-MAR (Philips) and MDT (ReVision Radiology), and CCS-MAR (Combined Clustered Scan-based MAR). Cycle-MAR was trained with a supervised learning scheme using sets of paired clinical CT scans with and without simulated artifacts. It was then evaluated on CT scans with real artifacts of an anthropomorphic phantom, and on sets of clinical CT scans with simulated artifacts which were not used for Cycle-MAR training. Image quality metrics and HU value-based analysis were used to evaluate the performance of Cycle-MAR compared to the other algorithms. The proposed Cycle-MAR network effectively reduces the negative impact of the metal artifacts. For example, the calculated HU value improvement percentage for the cardiac structures in the clinical CT scans was 59.58%, 62.22%, and 72.84% after MDT, CCS-MAR, and Cycle-MAR application, respectively. The application of MAR algorithms reduces the impact of US transducer-induced metal artifacts on CT scans. In comparison to iMAR, O-MAR, MDT, and CCS-MAR, the application of developed Cycle-MAR network on CT scans performs better in reducing these metal artifacts.

The effect of common dental fixtures on treatment planning and delivery for head and neck intensity modulated proton therapy

PURPOSE

Proton treatment plan perturbation by common dental fixtures such as amalgams (Am) and porcelain-fused-to-metal (PFM) crowns has, to date, been uncharacterized. Previous studies have been conducted to determine the physical effect of these materials within the beam path for single spots, but their effects on complex treatment plans and clinical anatomy have not yet been quantified. The present manuscript aims to study the effect of Am and PFM fixtures on proton treatment planning in a clinical setting.

METHODS

An anthropomorphic phantom with removable tongue, maxilla, and mandible modules was simulated on a clinical computed tomography (CT) scanner. Spare maxilla modules were modified to include either a 1.5 mm depth central groove occlusal amalgam (Am) or a porcelain-fused-to-metal (PFM) crown, implanted on the first right molar. Modified tongue modules were 3D printed to accommodate several axial or sagittal oriented pieces of EBT-3 film. Clinically representative spot-scanning proton plans were generated in Eclipse v.15.6 using the proton convolution superposition (PCS) algorithm v.15.6.06 using a multi-field optimization (MFO) technique with the goal of delivering a uniform 54 Gy dose to a clinical target volume (CTV) typical of a base-of-tongue (BoT) treatment. A typical geometric beam arrangement of two anterior oblique (AO) beams and a posterior beam was employed. Plans optimized without any material overrides were delivered to the phantom A) without implants; B) with Am fixture; or C) with PFM crown. Plans were also reoptimized and delivered with inclusion of material overrides to equate relative stopping power of the fixture with that of a previously measured result.

RESULTS

Plans exhibit slightly greater dose weight towards AO beams. The optimizer accounted for inclusion of fixture overrides by increasing beam weights to the beam closest to the implant. Film measurements exhibited cold spots directly within the beam path through the fixture in plans with and without overridden materials. Cold spots were somewhat mitigated in plans including overridden materials in the structure set but were not entirely eliminated. Cold spots associated with Am and PFM fixtures were quantified at 17% and 14% for plans without overrides, respectively, and 11% and 9% with using Monte Carlo simulation. Compared with film measurements and Monte Carlo simulation, the treatment planning system underestimates the dose shadowing effect in plans including material overrides.

CONCLUSIONS

Dental fixtures create a dose shadowing effect directly in line with the beam path through the material. This cold spot is partially mitigated by overriding the material to measured relative stopping powers. Due to uncertainties in modeling perturbation through the fixture, the magnitude of the cold spot is underestimated using the institutional TPS when compared to measurement and MC simulation.

Effects of reconstruction methods on dose distribution for lung stereotactic body radiotherapy treatment plans

The aim of the present study was to investigate the effect of tumour motion on various imaging strategies as well as on treatment plan accuracy for lung stereotactic body radiotherapy treatment (SBRT) cases. The ExacTrac gating phantom and paraffin were used to investigate respiratory motion and represent a lung tumour, respectively. Four-dimensional computed tomography (4DCT) imaging was performed, while the phantom was moving sinusoidally with 4 s cycling time with three different amplitudes of 8, 16, and 24 mm. Reconstructions were done with maximum (MIP) and average intensity projection (AIP) methods. Comparisons of target density and volume were performed using two reconstruction techniques and references values. Volumetric modulated arc therapy (VMAT) and intensity modulated radiation therapy (IMRT) were planned based on reconstructed computed tomography (CT) sets, and it was examined how density variations affect the dose-volume histogram (DVH) parameters. 4D cone beam computed tomography (CBCT) was performed with the Elekta Versa HD linac imaging system before irradiation and compared with 3D CBCT. Thus, various combinations of 4DCT reconstruction methods and treatment alignment methods have been investigated. Point measurements as well as 2 and 3D dose measurements were done by optically stimulated luminescence (OSL), gafchromic films, and electronic portal imaging devices (EPIDs), respectively. The mean volume reduction was 7.8% for the AIP and 2.6% for the MIP method. The obtained Hounsfield Unit (HU) values were lower for AIP and higher for MIP when compared with the reference volume density. In DVH analysis, there were no statistical differences for D_95%, D_98%, and D_mean (p > 0.05). However, D_2% was significantly affected by HU changes (p < 0.01). A positional variation was obtained up to 2 mm in moving direction when 4D CBCT was applied after 3D CBCT. Dosimetric measurements showed that the main part of the observed dose deviation was due to movement. In lung SBRT treatment plans, D_2% doses differ significantly according to the reconstruction method. Additionally, it has been observed that setups based on 3D imaging can cause a positional error of up to 2 mm compared to setups based on 4D imaging. It is concluded that MIP has advantages over AIP in defining internal target volume (ITV) in lung SBRT applications. In addition, 4D CBCT and 3D EPID dosimetry are recommended for lung SBRT treatments.

Clinical evaluation of vertebral body replacement of carbon fiber-reinforced polyetheretherketone in patients with tumor manifestation of the thoracic and lumbar spine

PURPOSE

Radiolucent anterior and posterior implants by carbon fiber-reinforced polyetheretherketone (CFR PEEK) aim to improve treatment of primary and secondary tumors of the spine during the last years. The aim of this study was to evaluate clinical and radiological outcomes after dorsoventral instrumentation using a CFR PEEK implant in a cohort of patients representing clinical reality.

METHODS

A total of 25 patients with tumor manifestation of the thoracic and lumbar spine underwent vertebral body replacement (VBR) using an expandable CFR PEEK implant between January 2021 and January 2022. Patient outcome, complications, and radiographic follow-up were analyzed.

RESULTS

A consecutive series aged 65.8 ± 14.7 (27.6-91.2) years were treated at 37 vertebrae of tumor manifestation, including two cases (8.0%) of primary tumor as well as 23 cases (92.0%) of spinal metastases. Overall, 26 cages covering a median of 1 level (1-4) were implanted. Duration of surgery was 134 ± 104 (65-576) min, with a blood loss of 792 ± 785 (100-4000) ml. No intraoperative cage revision was required. Surgical complications were reported in three (12.0%) cases including hemothorax in two cases (one intraoperative, one postoperative) and atrophic wound healing disorder in one case. In two cases (8.0%), revision surgery was performed (fracture of the adjacent tumorous vertebrae, progressive construct failure regarding cage subsidence). No implant failure was observed.

CONCLUSION

VBR using CFR PEEK cages represents a legitimate surgical strategy which opens a variety of improvements-especially in patients in need of postoperative radiotherapy of the spine and MRI-based follow-up examinations.

DuDoUFNet: Dual-Domain Under-to-Fully-Complete Progressive Restoration Network for Simultaneous Metal Artifact Reduction and Low-Dose CT Reconstruction

To reduce the potential risk of radiation to the patient, low-dose computed tomography (LDCT) has been widely adopted in clinical practice for reconstructing cross-sectional images using sinograms with reduced x-ray flux. The LDCT image quality is often degraded by different levels of noise depending on the low-dose protocols. The image quality will be further degraded when the patient has metallic implants, where the image suffers from additional streak artifacts along with further amplified noise levels, thus affecting the medical diagnosis and other CT-related applications. Previous studies mainly focused either on denoising LDCT without considering metallic implants or full-dose CT metal artifact reduction (MAR). Directly applying previous LDCT or MAR approaches to the issue of simultaneous metal artifact reduction and low-dose CT (MARLD) may yield sub-optimal reconstruction results. In this work, we develop a dual-domain under-to-fully-complete progressive restoration network, called DuDoUFNet, for MARLD. Our DuDoUFNet aims to reconstruct images with substantially reduced noise and artifact by progressive sinogram to image domain restoration with a two-stage progressive restoration network design. Our experimental results demonstrate that our method can provide high-quality reconstruction, superior to previous LDCT and MAR methods under various low-dose and metal settings.

CFR-PEEK Pedicle Screw Instrumentation for Spinal Neoplasms: A Single Center Experience on Safety and Efficacy

Simple Summary

Advances in screening methods and new therapeutic strategies have lead to a continuous decline in cancer death rates, especially over the last ten years. As a consequence, the number of patients with spinal metastases is increasing. In modern oncological treatment surgery followed by postoperative radiotherapy for spinal metastases has gained a decisive role. For spinal stabilization, pedicle screws and rods are used. They used to be made of titanium or cobalt–chrome alloys. Recently, carbon-fiber-reinforced (CFR) polyethyl-ether-ether-ketone (PEEK) was introduced as a new material reducing artifacts on imaging and showing less perturbation effects on photon radiation. The aim of this study is to report on the safety and efficacy of CFR-PEEK pedicle screw systems for spinal neoplasms in a large cohort of consecutive patients. We could show that implant-related complications, such as intraoperative screw breakage and screw loosening, were rare. So, we conclude that CFR-PEEK is a safe and efficient alternative to titanium for oncological spinal instrumentation.

Abstract

(1) Background: Surgery for spinal metastases has gained a decisive role in modern oncological treatment. Recently, carbon-fiber-reinforced (CFR) polyethyl-ether-ether-ketone (PEEK) pedicle screw systems were introduced, reducing artifacts on imaging and showing less perturbation effects on photon radiation. Preliminary clinical experience with CFR-PEEK implants for spinal metastases exists. The aim of this monocentric study is to report on the safety and efficacy of CFR-PEEK pedicle screw systems for spinal neoplasms in a large cohort of consecutive patients. (2) Methods: We retrospectively analyzed prospectively the collected data of consecutive patients being operated on from 1 August 2015 to 31 October 2021 using a CFR-PEEK pedicle screw system for posterior stabilization because of spinal metastases or primary bone tumors of the spine. (3) Results: We included 321 patients of a mean age of 65 ± 13 years. On average, 5 ± 2 levels were instrumented. Anterior reconstruction was performed in 121 (37.7%) patients. Intraoperative complications were documented in 30 (9.3%) patients. Revision surgery for postoperative complications was necessary in 55 (17.1%) patients. Implant-related complications, such as intraoperative screw breakage (3.4%) and screw loosening (2.2%), were rare. (4) Conclusions: CFR-PEEK is a safe and efficient alternative to titanium for oncological spinal instrumentation, with low complication and revision rates in routine use and with the advantage of its radiolucency.

Low-dimensional Manifold Constrained Disentanglement Network for Metal Artifact Reduction

Deep neural network based methods have achieved promising results for CT metal artifact reduction (MAR), most of which use many synthesized paired images for supervised learning. As synthesized metal artifacts in CT images may not accurately reflect the clinical counterparts, an artifact disentanglement network (ADN) was proposed with unpaired clinical images directly, producing promising results on clinical datasets. However, as the discriminator can only judge if large regions semantically look artifact-free or artifact-affected, it is difficult for ADN to recover small structural details of artifact-affected CT images based on adversarial losses only without sufficient constraints. To overcome the illposedness of this problem, here we propose a low-dimensional manifold (LDM) constrained disentanglement network (DN), leveraging the image characteristics that the patch manifold of CT images is generally low-dimensional. Specifically, we design an LDM-DN learning algorithm to empower the disentanglement network through optimizing the synergistic loss functions used in ADN while constraining the recovered images to be on a low-dimensional patch manifold. Moreover, learning from both paired and unpaired data, an efficient hybrid optimization scheme is proposed to further improve the MAR performance on clinical datasets. Extensive experiments demonstrate that the proposed LDM-DN approach can consistently improve the MAR performance in paired and/or unpaired learning settings, outperforming competing methods on synthesized and clinical datasets.

Impact of different fixed dental prostheses on radiation dose in helical tomotherapy as measured with metal oxide semiconductor field-effect transistor dosimetry

OBJECTIVE

This ex vivo study evaluated the effects of different fixed dental prostheses and protective materials on scattered radiation during radiation therapy (RT).

STUDY DESIGN

Natural teeth (group NT) and 4 types of prostheses (group BL: bilayer lithium disilicate glass-ceramic; group MZ: monolithic zirconia ceramic; group BZ: bilayer zirconia-based all ceramic; and group BM: bilayer metal-ceramic restorations) were examined in maxillary and mandibular arch phantoms. All groups were divided into 3 subgroups: (1) without protective material over the prostheses; (2) protected with a soft acrylic night guard; and (3) protected with polyvinylsiloxane putty. All groups were irradiated with helical RT at 2 Gy and 6 MV photon energy. Doses were measured internally and externally 3 times on each phantom. Results were significant at P < .05.

RESULTS

No statistically significant differences in doses were found between groups NT and BL in either phantom, but these groups were different from the others. The differences between groups BZ and MZ were insignificant. Doses in group BM were significantly larger than all other groups. No significant differences existed between doses with and without protective material.

CONCLUSIONS

Doses increased significantly due to scattered radiation from the prostheses with increasing material density. Protective materials had no significant effect on dose.

Modification of polyether ether ketone for the repairing of bone defects

Bone damage as a consequence of disease or trauma is a common global occurrence. For bone damage treatment - bone implant materials are necessary across three classifications of surgical intervention (i.e. fixation, repair, and replacement). Many types of bone implant materials have been developed to meet the requirements of bone repair. Among them, polyether ether ketone (PEEK) has been considered as one of the next generation of bone implant materials, owing to its advantages related to good biocompatibility, chemical stability, X-ray permeability, elastic modulus comparable to natural bone, as well as the ease of processing and modification. However, as PEEK is a naturally bioinert material, some modification is needed to improve its integration with adjacent bones after implantation. Therefore, it has become a very hot topic of biomaterials research and various strategies for the modification of PEEK including blending, 3D printing, coating, chemical modification and the introduction of bioactive and/or antibacterial substances have been proposed. In this systematic review, the recent advances in modification of PEEK and its application prospect as bone implants are summarized, and the remaining challenges are also discussed.

Physical characterization of therapeutic proton delivery through common dental materials

PURPOSE

Dental fixtures are commonplace in an aging, radiation treatment population. The current, local standard of practice in particle therapy is to employ treatment geometries to avoid delivery through implanted dental fixtures. The present study aims to observe the physical effect of delivering therapeutic proton beams through common dental fixture materials as prelude to an eventual goal of assessing the feasibility of using treatment geometries not specified for avoidance of oral implants. A sampling of common dental materials was selected based on prosthodontic consult and was evaluated in terms of relative stopping power and three-dimensional (3D) dose perturbation.

METHODS

Amalgams, porcelain-fused-to-metal (PFM) crowns consisting of zirconia and non-noble base metals, and lithium disilicate implants were chosen for analysis. Theoretical stopping power (S) and mass stopping power (S/ρ) were calculated using the Stopping and Range of Ions in Matter (SRIM) application, basing stoichiometric compositions of each fixture on published materials data. S and S/ρ were calculated for a range of historically available compositions of amalgams from 1900 until the current era. The perturbance of S and S/ρ as a function of clinically relevant ranges of amalgam compositions for the modern era was analyzed. Water equivalent thickness (WET) and relative stopping power (S_rel ) of each material was measured for a clinical spot-scanning proton beam with monoenergies of 159.9 and 228.8 MeV with a multi-layer ionization chamber (MLIC). Subsequently, 3D dose perturbation was assessed by delivering proton beams through a custom phantom designed to simulate both en-face and on-edge treatment geometries through the selected materials. A treatment plan mimicking the experimental delivery was constructed in the institutional treatment planning system and calculated using TOPAS based Monte Carlo Simulation (MCS). Experimental results were used to validate the MCS. Finally, TPS outputs were compared to MCS to determine the accuracy of the dose calculation model.

RESULTS

Historical compositions of amalgams ranged in S from 44.8 to 42.9 MeV/cm, with the greatest deviation being observed for the 1900-1959 era. Deviation as a function of amalgam composition from the modern era was most sensitive to proportion of Hg, accounting for deviations up to -4.2% at the greatest clinically relevant concentration. S/ρ was not found to vary greatly between each porcelain and metal alloy material for porcelain-fused-to-metal (PFM) type crowns. Relative stopping powers ranged between 1.3 and 5.4 for all studied materials, suggesting substantial changes in proton range with respect to water. Film measurements of pristine spots confirm dose perturbance and shortening of proton range, with an upstream shift of each Bragg peak being observed directly behind the installed fixture. At high energies, cold spots were found in all cases directly behind each material feature with a medial fill-in of dose occurring distally. Qualitative agreement of spot perturbance was confirmed between film measurements and MCS. Finally, when comparing integrated depth doses (IDD) by summing over all axial directions, good agreement is observed between TPS and MCS.

CONCLUSIONS

All dental materials studied substantially perturbed the dosimetry of pristine proton spots both in terms of WET/S_rel as well as the spatial distribution of dose. Proton range was quantifiably shortened, and each dental material affected a cold spot directly behind the object with medial dose back-filling was observed distally. Monte Carlo simulations and Eclipse dose calculations exhibited good agreement with measurements, suggesting that treatment planning without employing avoidance strategies may be possible with further investigation. This article is protected by copyright. All rights reserved.

Dosimetric evaluation of high-Z inhomogeneity used for hip prosthesis: A multi-institutional collaborative study

PURPOSE

A multi-institutional investigation for dosimetric evaluation of high-Z hip prosthetic device in photon beam.

METHODS

A bilateral hip prosthetic case was chosen. An in-house phantom was built to replicate the human pelvis with two different prostheses. Dosimetric parameters: dose to the target and organs at risk (OARs) were compared for the clinical case generated by various treatment planning system (TPS) with varied algorithms. Single beam plans with different TPS for phantom using 6 MV and 15 MV photon beams with and without density correction were compared with measurement.

RESULTS

Wide variations in target and OAR dosimetry were recorded for different TPS. For clinical case ideal PTV coverage was noted for plans generated with Corvus and Prowess TPS only. However, none of the TPS were able to meet plan objective for the bladder. Good correlation was noticed for the measured and the Pinnacle TPS for corrected dose calculation at the interfaces as well as the dose ratio in elsewhere. On comparing measured and calculated dose, the difference across the TPS varied from -20% to 60% for 6 MV and 3% to 50% for the 15 MV, respectively.

CONCLUSION

Most TPS do not provide accurate dosimetry with high-Z prosthesis. It is important to check the TPS under extreme conditions of beams passing through the high-Z region. Metal artifact reduction algorithms may reduce the difference between the measured and calculated dose but still significant differences exist. Further studies are required to validate the calculational accuracy.

Case Report: Role of an Iodinated Rectal Hydrogel Spacer, SpaceOAR Vue™, in the Context of Low-Dose-Rate Prostate Brachytherapy, for Enhanced Post-Operative Contouring to Aid in Accurate Implant Evaluation and Dosimetry

We present a case series of 13 consecutive patients with prostate cancer treated with low-dose-rate (LDR) brachytherapy, utilizing SpaceOAR Vue™, the recent iodinated iteration of the SpaceOAR™ hydrogel rectal spacer. Low- and favorable intermediate-risk patients receiving monotherapy and unfavorable intermediate- and high-risk patients undergoing a brachytherapy boost were included. Permanent brachytherapy can result in subacute and late rectal toxicity, and precise contouring of the anterior rectal wall and posterior aspect of the prostate is essential for accurate dosimetry to confirm a safe implant. Clearly visible on non-contrast CT imaging, SpaceOAR Vue™ can substantially aid in post-implant contouring and analysis. Not previously described in the literature in the context of LDR brachytherapy, we demonstrate the added clinical benefit of placing a well-visualized rectal spacer.

Comprehensive Evaluation of Carbon-Fiber-Reinforced Polyetheretherketone (CFR-PEEK) Spinal Hardware for Proton and Photon Planning

Purpose: To evaluate a novel spine implant, carbon-fiber-reinforced polyetheretherketone (CFR-PEEK), for proton and photon treatment planning. Materials and Methods: We compared target coverage and sparing of organs-at-risk (OARs) for a spinal phantom with 4 different spine configurations: (a) normal (no implant); (b) Titanium; (c) CFR-PEEK; and (d) hybrid (CFR-PEEK with Titanium tulip head). The spinal phantom was imaged via computed tomography (CT) scan, and the iterative Metal Artifact Reduction (iMAR) CT set was used for planning. A representative spinal chordoma target and associated OARs were contoured. The prescription dose was 50 Gy to the initial target volume, followed by a 24 Gy boost, for which multi-field optimization (MFO) proton plans were developed with a 3 mm setup and 3.5% range uncertainties. For photon planning, volumetric modulated arc therapy (VMAT) plans were developed for the initial and boost plans. OAR dose constraints were set according to our institutional guidelines. Results: For the 4 spine configurations, the proton plans achieved similar nominal target coverage and OARs sparing. While evaluating coverage and OAR dose under uncertainty scenario analysis for initial clinical target volume (CTV) 50 Gy 95% and 90% coverage, higher means and the narrower band of doses variations were achieved for the normal and CFR-PEEK plans. Similarly, uncertainty analysis of spinal cord D_max showed tighter distribution for normal and CFR-PEEK plans. Overall plan quality showed no significant difference for photon planning when compared to normal spine versus other inserts. However, for proton planning, there is a larger difference for the normal spine insert scenario versus the Titanium insert scenario. For each insert scenario comparison between photon and proton plans, there was a larger difference for OARs: heart and spinal cord. Conclusion: The CFR-PEEK implant has similar clinical properties to a normal spine for proton planning, allowing us to pass protons through the material and achieve superior target coverage and OAR sparing under nominal and uncertainty conditions.

DuDoDR-Net: Dual-domain data consistent recurrent network for simultaneous sparse view and metal artifact reduction in computed tomography

Sparse-view computed tomography (SVCT) aims to reconstruct a cross-sectional image using a reduced number of x-ray projections. While SVCT can efficiently reduce the radiation dose, the reconstruction suffers from severe streak artifacts, and the artifacts are further amplified with the presence of metallic implants, which could adversely impact the medical diagnosis and other downstream applications. Previous methods have extensively explored either SVCT reconstruction without metallic implants, or full-view CT metal artifact reduction (MAR). The issue of simultaneous sparse-view and metal artifact reduction (SVMAR) remains under-explored, and it is infeasible to directly apply previous SVCT and MAR methods to SVMAR which may yield non-ideal reconstruction quality. In this work, we propose a dual-domain data consistent recurrent network, called DuDoDR-Net, for SVMAR. Our DuDoDR-Net aims to reconstruct an artifact-free image by recurrent image domain and sinogram domain restorations. To ensure the metal-free part of acquired projection data is preserved, we also develop the image data consistent layer (iDCL) and sinogram data consistent layer (sDCL) that are interleaved in our recurrent framework. Our experimental results demonstrate that our DuDoDR-Net is able to produce superior artifact-reduced results while preserving the anatomical structures, that outperforming previous SVCT and SVMAR methods, under different sparse-view acquisition settings.

Anterior Corpectomy and Plating with Carbon-PEEK Instrumentation for Cervical Spinal Metastases: Clinical and Radiological Outcomes

Background: Anterior cervical corpectomy and plating has been recognized as a valuable approach for the surgical treatment of cervical spinal metastases. This study aimed to report the surgical, clinical and radiological outcomes of anterior carbon-PEEK instrumentations for cervical spinal metastases. Methods: Demographical, clinical, surgical and radiological data were collected from 2017 to 2020. The Neck Disability Index (NDI) questionnaire for neck pain, EORTC QLQ-C30 questionnaire for quality of life, Nurick scale for myelopathy and radiological parameters (segmental Cobb angle and cervical lordosis) were collected before surgery, at 6 weeks postoperatively and follow-up. Results: Seventeen patients met inclusion criteria. Mean age was 60.9 ± 7.6 years and mean follow-up was 12.9 ± 4.0 months. The NDI (55.4 ± 11.7 to 25.1 ± 5.4, p < 0.001) scores and the EORTC QLQ-C30 global health/QoL significantly improved postoperatively and at the last follow-up. The segmental Cobb angle (10.7° ± 5.6 to 3.1° ± 2.2, p < 0.001) and cervical lordosis (0.9° ± 6.7 to −6.2 ± 7.8, p = 0.002) significantly improved postoperatively. Only one minor complication (5.9%) was recorded. Conclusions: Carbon/PEEK implants represent a safe alternative to commonly used titanium ones and should be considered in cervical spinal metastases management due to their lower artifacts in postoperative imaging and radiation planning. Further larger comparative and cost-effectiveness studies are needed to confirm these results.

Improving radiation physics, tumor visualisation, and treatment quantification in radiotherapy with spectral or dual-energy CT

Over the past decade, spectral or dual‐energy CT has gained relevancy, especially in oncological radiology. Nonetheless, its use in the radiotherapy (RT) clinic remains limited. This review article aims to give an overview of the current state of spectral CT and to explore opportunities for applications in RT.

In this article, three groups of benefits of spectral CT over conventional CT in RT are recognized. Firstly, spectral CT provides more information of physical properties of the body, which can improve dose calculation. Furthermore, it improves the visibility of tumors, for a wide variety of malignancies as well as organs‐at‐risk OARs, which could reduce treatment uncertainty. And finally, spectral CT provides quantitative physiological information, which can be used to personalize and quantify treatment.

Vestibuloplasty for immediate dental implantation in fibular free flap for oral cancer patients undergoing mandibulectomy reconstruction: A technical note

Vestibuloplasty is fundamental to restore an oral vestibule for immediate dental implantation in fibular free flap (FFF) for oral cancer patients undergoing mandibulectomy reconstruction. Double surgical team including reconstructive head and neck surgeon and a dental surgeon is fundamental. The first step of the vestibuloplasty is to identify the skin perforator. The second step is to thin the FFF skin island as much as necessary to facilitate: i-the reinset into the gingivobuccal sulcus while creating enough space in the oral vestibule for the future dental prosthesis and ii-the exposition of dental implants. The third step is to create a percutaneous access to the implants through the FFF skin paddle using a dermatologic punch while preserving a large oral vestibule. The fourth step is the skin reinsertion into the gingivobuccal sulcus and closure. Realizing vestibuloplasty before radiotherapy allows prevention of soft tissue contraction and osteoradionecrosis while reducing the necessary time for a complete dental rehabilitation and improving patient quality of life.

Iterative Metal Artifact Reduction (iMAR) of the Non-adhesive Liquid Embolic Agent Onyx in Computed Tomography : An Experimental Study

Background

A drawback of Onyx, one of the most used embolic agents for endovascular embolization of intracranial arteriovenous malformations (AVM), is the generation of imaging artifacts (IA) in computed tomography (CT). Since these artifacts can represent an obstacle for the detection of periprocedural bleeding, this study investigated the effect of artifact reduction by an iterative metal artifact reduction (iMAR) software in CT in a brain phantom.

Methods

Two different in vitro models with two-dimensional tube and three-dimensional AVM-like configuration were filled with Onyx 18. The models were inserted into a brain imaging phantom and images with (n = 5) and without (n = 10) an experimental hemorrhage adjacent were acquired. Afterwards, the iMAR algorithm was applied for artifact reduction. The IAs of the original and the post-processed images were graded quantitatively and qualitatively. Moreover, qualitative definition of the experimental hemorrhage was investigated.

Results

Comparing the IAs of the original and the post-processed CT images, quantitative and qualitative analysis showed a lower degree of IAs in the post-processed images, i.e. quantitative analysis: 2D tube model: 23.92 ± 8.02 Hounsfield units (HU; no iMAR; mean ± standard deviation) vs. 5.93 ± 0.43 HU (with iMAR; p < 0.001); qualitative analysis: 3D AVM model: 4.93 ± 0.18 vs. 3.40 ± 0.48 (p < 0.001). Furthermore, definition of the experimental hemorrhage was better in the post-processed images of both in vitro models (2D tube model: p = 0.004; 3D AVM model: p = 0.002).

Conclusion

The iMAR algorithm can significantly reduce the IAs evoked by Onyx 18 in CT. Applying iMAR could thus improve the accuracy of postprocedural CT imaging after embolization with Onyx in clinical practice.

Gel and thermoluminescence dosimetry for dose verifications of a real anatomy simulated prostate conformal radiation treatment in the presence of metallic femoral prosthesis

This study aims to verify the dose delivery of prostate radiotherapy treatments in an adult pelvic phantom with two metallic hip and femur prosthesis using a four‐field box technique. The prostate planned target volume (PTV) tridimensional (3D) dose distribution was evaluated using gel dosimetry, and thermoluminescent dosimeters (TLD) were used for point‐dose measurements outside it. Both results were compared to the treatment planning system (TPS) dose calculation without using heterogeneity corrections to evaluate the influence of the metal in the dose distribution. MAGIC‐f gel dosimeter (Methacrylic and Ascorbic acid in Gelatin Initiated by Copper with Formaldehyde) associated with magnetic resonance imaging was used. TLD were positioned at several points at the bone metal interface and the sacrum region. The comparison of the gel measured and the TPS calculated dose distributions were done using gamma analysis (3%/3 mm), and a pass rate of 93% was achieved. The TLD dose values at the bone‐metal interface showed variations from the planned dose. However, at the sacrum region, where the beams did not intercept the prosthesis, there was a good agreement between TPS planning and TLD measurements. Our results show how the combination of 3D dosimetry and measurements at specific points in the phantom allowed a comprehensive view of the dose distribution and identified that care must also be paid to regions outside the PTV.

The impact of software-based metal artifact reduction on the liquid embolic agent Onyx in cone-beam CT: a systematic in vitro and in vivo study

Background

Onyx is frequently used for endovascular embolization of intracranial arteriovenous malformations (AVMs) and dural arteriovenous fistulas (dAVFs). One drawback of using Onyx is the generation of artifacts in cone-beam CT (CBCT). These artifacts can represent an obstacle for the detection of periprocedural hemorrhage or planning of subsequent radiosurgery. This study investigates the effect of artifact reduction by the syngo DynaCT SMART Metal Artifact Reduction (MAR) software.

Methods

A standardized in vitro tube model (n=10) was filled with Onyx 18 and CBCT image acquisition was conducted in a brain imaging phantom. Furthermore, post-interventional CBCT images of 20 patients with AVM (n=13) or dAVF (n=7), each treated with Onyx, were investigated. The MAR software was applied for artifact reduction. Artifacts of the original and the post-processed images were analyzed quantitatively (standard deviation in a region of interest on the layer providing the most artifacts) and qualitatively. For the patient images, the effect of the MAR software on brain parenchyma on artifact-free images was further investigated.

Results

Quantitative and qualitative analyses of both datasets demonstrated a lower degree of artifacts in the post-processed images (eg, patient images: 38.30±22.03 density units (no MAR; mean SD±SD) vs 19.83±12.31 density units (with MAR; p<0.001). The MAR software had no influence on the brain parenchyma in artifact-free images.

Conclusion

The MAR software significantly reduced the artifacts evoked by Onyx in CBCT without affecting the visualization of brain parenchyma on artifact-free images. Applying this software could thus improve the quality of periprocedural CBCT images after embolization with Onyx.

Glue, Onyx, Squid or PHIL? Liquid Embolic Agents for the Embolization of Cerebral Arteriovenous Malformations and Dural Arteriovenous Fistulas

Background

Endovascular embolization is an effective treatment option for cerebral arteriovenous malformations (AVMs) and dural arteriovenous fistulas (DAVFs). A variety of liquid embolic agents have been and are currently used for embolization of AVMs and DAVFs. Knowledge of the special properties of the agent which is used is crucial for an effective and safe embolization procedure.

Material and Methods

This article describes the properties and indications of the liquid embolic agents which are currently available: cyanoacrylates (also called glues), and the copolymers Onyx, Squid and PHIL, as well as their respective subtypes.

Results

Cyanoacrylates were the predominantly used agents in the 1980s and 1990s. They are currently still used in specific situations, for example for the occlusion of macro-shunts, for the pressure cooker technique or in cases in which microcatheters are used that are not compatible with dimethyl-sulfoxide. The first broadly used copolymer-based embolic agent Onyx benefits from a large amount of available experience and data, which demonstrated its safety and efficacy in the treatment of cerebral vascular malformations, while its drawbacks include temporary loss of visibility during longer injections and artifacts in cross-sectional imaging. The more recently introduced agents Squid and PHIL aim to overcome these shortcomings and to improve the success rate of endovascular embolization. Novelties of these newer agents with potential advantages include extra-low viscosity versions, more stable visibility, and a lower degree of imaging artifacts.

Conclusion

All the available liquid embolic agents feature specific potential advantages and disadvantages over each other. The choice of the most appropriate embolic agent must be made based on the specific material characteristics of the agent, related to the specific anatomical characteristics of the target pathology.

Dosimetric impact of using a commercial metal artifact reduction tool in carbon ion therapy in patients with hip prostheses

The study investigated the dosimetric impact of an iterative metal artifact reduction (iMAR) tool on carbon ion therapy for pelvic cancer patients with hip prostheses. An anthropomorphic pelvic phantom with unilateral and bilateral hip prostheses was used to simulate pelvic cancer patients with metal implants. The raw data obtained from phantom CT scanning were reconstructed with a regular filtered back projection (FBP) algorithm and then corrected with iMAR. The phantom without hip prosthesis was also scanned and used as a reference ground truth (GT). The CT images of three prostate and four sarcoma patients with unilateral hip prosthesis were also reconstructed by FBP and iMAR algorithm and compared. iMAR algorithm reduced the metal artifacts and the maximum WEPL deviation in phantom images from −19.1 to −0.4 mm. However, the CT numbers cannot be retrieved using iMAR for periprosthetic bone materials, eventually leading to a WEPL deviation of −3.6 mm. The use of iMAR improved large discrepancies in DVHs of PTVs and the gamma index between FBP and GT images but increased the difference in the bladder DVH for bilateral hip prostheses due to newly introduced artifacts. In the patient study, the discrepancies of dose distribution were small on iMAR images when compared with FBP images for most cases, except for two sarcoma cases where gamma analysis failed and dose coverage in 98% of the PTV maximally reduced due to large volume of dark metal artifacts. iMAR reduced the metal artifacts and improved dose distribution accuracy in carbon ion radiotherapy for pelvic cancer. However, the residual and newly introduced artifacts, especially with bilateral hip prostheses, may potentially increase WEPL inaccuracy and dose uncertainty. The use of iMAR has the potential to improve carbon ion treatment planning of pelvic cancer but should be used with caution.

Geometric and dosimetric impact of 3D generative adversarial network-based metal artifact reduction algorithm on VMAT and IMPT for the head and neck region

Background

We investigated the geometric and dosimetric impact of three-dimensional (3D) generative adversarial network (GAN)-based metal artifact reduction (MAR) algorithms on volumetric-modulated arc therapy (VMAT) and intensity-modulated proton therapy (IMPT) for the head and neck region, based on artifact-free computed tomography (CT) volumes with dental fillings.

Methods

Thirteen metal-free CT volumes of the head and neck regions were obtained from The Cancer Imaging Archive. To simulate metal artifacts on CT volumes, we defined 3D regions of the teeth for pseudo-dental fillings from the metal-free CT volumes. HU values of 4000 HU were assigned to the selected teeth region of interest. Two different CT volumes, one with four (m4) and the other with eight (m8) pseudo-dental fillings, were generated for each case. These CT volumes were used as the Reference. CT volumes with metal artifacts were then generated from the Reference CT volumes (Artifacts). On the Artifacts CT volumes, metal artifacts were manually corrected for using the water density override method with a value of 1.0 g/cm³ (Water). By contrast, the CT volumes with reduced metal artifacts using 3D GAN model extension of CycleGAN were also generated (GAN-MAR). The structural similarity (SSIM) index within the planning target volume was calculated as quantitative error metric between the Reference CT volumes and the other volumes. After creating VMAT and IMPT plans on the Reference CT volumes, the reference plans were recalculated for the remaining CT volumes.

Results

The time required to generate a single GAN-MAR CT volume was approximately 30 s. The median SSIMs were lower in the m8 group than those in the m4 group, and ANOVA showed a significant difference in the SSIM for the m8 group (p < 0.05). Although the median differences in D_98%, D_50% and D_2% were larger in the m8 group than the m4 group, those from the reference plans were within 3% for VMAT and 1% for IMPT.

Conclusions

The GAN-MAR CT volumes generated in a short time were closer to the Reference CT volumes than the Water and Artifacts CT volumes. The observed dosimetric differences compared to the reference plan were clinically acceptable.

The application of metal artifact reduction methods on computed tomography scans for radiotherapy applications: A literature review

Metal artifact reduction (MAR) methods are used to reduce artifacts from metals or metal components in computed tomography (CT). In radiotherapy (RT), CT is the most used imaging modality for planning, whose quality is often affected by metal artifacts. The aim of this study is to systematically review the impact of MAR methods on CT Hounsfield Unit values, contouring of regions of interest, and dose calculation for RT applications. This systematic review is performed in accordance with the PRISMA guidelines; the PubMed and Web of Science databases were searched using the main keywords "metal artifact reduction", "computed tomography" and "radiotherapy". A total of 382 publications were identified, of which 40 (including one review article) met the inclusion criteria and were included in this review. The selected publications (except for the review article) were grouped into two main categories: commercial MAR methods and research-based MAR methods. Conclusion: The application of MAR methods on CT scans can improve treatment planning quality in RT. However, none of the investigated or proposed MAR methods was completely satisfactory for RT applications because of limitations such as the introduction of other errors (e.g., other artifacts) or image quality degradation (e.g., blurring), and further research is still necessary to overcome these challenges.

[A Simple Method for Computationally Generating Metal Artifacts in CT Images for Treatment Planning: A Pilot Phantom Study]

PURPOSE

In treatment planning for radiation therapy, the use of computed tomography (CT) images including metal artifacts causes a reduction in the dose calculation accuracy. In clinical practice, the artifacts are manually contoured and assigned an appropriate fixed CT number. To validate the procedure, images taken before and after metal insertion into a patient are required, which may be impractical. We propose a simple method for computationally generating metal artifacts in clinical images.

METHODS

In the proposed method, a clinical image free of metal artifacts is used. To simulate metal inside a patient, CT numbers of a region in the image are replaced with a fixed extremely high value. A sinogram is created by the forward projection of the image. Data values of the sinogram in the metal region are converted into smaller values. From the sinogram, an image including artifacts is reconstructed with the filtered back projection.

RESULTS

The simulated artifacts consisted of dark and bright bands and were observed to be similar to the actual metal artifacts. CT numbers in multiple small regions of interest in the image obtained by the proposed method showed a good agreement with those in the actual image.

CONCLUSION

The proposed method was demonstrated to generate the metal artifacts additionally on the clinical images. The method would be potentially applicable to a validation study for the clinical procedure of manually contouring and assigning CT numbers to metal artifacts.

Imaging Artifacts of Nonadhesive Liquid Embolic Agents in Conventional and Cone-beam CT in a Novel in Vitro AVM Model

Background

A major drawback of liquid embolic agents (LEAs) is the generation of imaging artifacts (IA), which may represent a crucial obstacle for the detection of periprocedural hemorrhage or subsequent radiosurgery of cerebral arteriovenous malformations (AVMs). This study aimed to compare the IAs of Onyx, Squid and PHIL in a novel three-dimensional in vitro AVM model in conventional computed tomography (CT) and cone-beam CT (CBCT).

Methods

Tubes with different diameters were configured in a container resembling an AVM with an artificial nidus at its center. Subsequently, the AVM models were filled with Onyx 18, Squid 18, PHIL 25% or saline and inserted into an imaging phantom (n = 10/LEA). Afterwards CT and CBCT scans were acquired. The degree of IAs was graded quantitatively (Hounsfield units in a defined region of interest) and qualitatively (feasibility of defining the nidus)—Onyx vs. Squid vs. PHIL vs. saline, respectively.

Results

Quantitative density evaluation demonstrated more artifacts for Onyx compared to Squid and PHIL, e.g. 48.15 ± 14.32 HU for Onyx vs. 7.56 ± 1.34 HU for PHIL in CT (p < 0.001) and 41.88 ± 7.22 density units (DU) for Squid vs. 35.22 ± 5.84 DU for PHIL in CBCT (p = 0.044). Qualitative analysis showed less artifacts for PHIL compared to Onyx and Squid in both imaging modalities while there was no difference between Onyx and Squid regarding the definition of the nidus (p > 0.999).

Conclusion

In this novel three-dimensional in vitro AVM model, IAs were higher for the EVOH/tantalum-based LEAs Onyx and Squid compared to iodine-based PHIL. Onyx induced the highest degree of IAs with only minor differences to Squid.