Wetting effects on in vitro bioactivity and in vitro biocompatibility of laser micro-textured Ca-P coating

In-vitro biomineralization and biocompatibility of friction stir additively manufactured AZ31B magnesium alloy-hydroxyapatite composites

The present study aims to evaluate effect of hydroxyapatite (HA, Ca₁₀(PO₄)₆OH₂), a ceramic similar to natural bone, into AZ31B Mg alloy matrix on biomineralization and biocompatibility. The novel friction stir processing additive manufacturing route was employed to fabricate Mg-HA composites. Various HA contents (5, 10, 20 wt%) were incorporated into Mg matrix.

Microstructural observation and chemical composition analysis revealed that refined Mg grains and dispersion of HA particles at micro/nanoscales were achieved in Mg-HA composites after the friction stir processing. The biomineralization evaluation were carried out using immersion experiments in simulated body fluid followed by mineral morphology observation and chemical composition analysis. The wettability measurements were conducted to correlate the biomineralization behavior. The results showed improvement in wettability and bone-like Ca/P ratio in apatite deposit on the composites compared to as-received Mg. In addition, the increase of blood compatibility, cell viability and spreading were found in the higher HA content composites, indicating the improved biocompatibility. Therefore, friction stir processed Mg-20 wt%HA composite exhibited the highest wettability and better cell adhesion among other composites due to the effect of increased HA content within Mg matrix.

•

Friction stir additive manufacturing technique was employed to fabricate AZ31B magnesium-hydroxyapatite composite.

•

Hydroxyapatite incorporated in Mg matrix varied from micro-to nano-length scales.

•

Refined microstructure and increase in hydroxyapatite content enhanced wettability, biomineralization, and biocompatibility.

Laser fabrication of structural bone: surface morphology and biomineralization assessment

The current work explores the surface morphology of the laser-ablated bone using Yb-fiber coupled Nd:YAG laser (λ = 1064 nm) in continuous wave mode. As the laser-ablated region contains physiochemically modified carbonized and nonstructural region, it becomes unknown material for the body. Thus, biomineralization on such a laser-ablated region was assessed by in vitro immersion test in noncellular simulated body fluid. The presence of hydroxyapatite was detected in the precipitated mineral product using scanning electron microscopy equipped with energy dispersive spectroscopy, and X-ray diffraction analysis. The effect of varying laser parameters on distribution of surface morphology features was identified and its corresponding effect on biomineralization was studied.

Study on microstructure, microhardness, bioactivity, and biocompatibility of La2 O3 -containing bioceramic coating doping SiO2 fabricated by laser cladding

To solve the lack of strength of calcium phosphate ceramic coatings in load-bearing applications, gradient Ca-P bioceramic coatings doped with La₂ O₃ and SiO₂ are fabricated by laser cladding on Ti-6Al-4 V. The effect of SiO₂ on microstructure, microhardness, bioactivity, and biocompatibility of coatings was investigated. The experimental results illustrate that the coating doped with La₂ O₃ and SiO₂ has excellent metallurgical bonding. The XRD analysis confirms that the amount of hydroxyapatite and tricalcium phosphate in the coating reached maximum when doping amount of SiO₂ is 10 wt %. SiO₂ -doped coatings show a significantly higher bone-like apatite precipitation after immersion in SBF than that of other coatings. in vitro experiment also shows that coating with 10 wt % SiO₂ is more suitable for the attachment and proliferation of MG63 cells, indicating that coating with 10 wt % SiO₂ exhibits best bioactivity and biocompatibility. These results suggest that the addition of SiO₂ improves the bonding strength, bioactivity, and biocompatibility of coatings.

Fundamentals of Laser-Based Hydrogel Degradation and Applications in Cell and Tissue Engineering

The cell and tissue engineering fields have profited immensely through the implementation of highly structured biomaterials. The development and implementation of advanced biofabrication techniques have established new avenues for generating biomimetic scaffolds for a multitude of cell and tissue engineering applications. Among these, laser-based degradation of biomaterials is implemented to achieve user-directed features and functionalities within biomimetic scaffolds. This review offers an overview of the physical mechanisms that govern laser-material interactions and specifically, laser-hydrogel interactions. The influences of both laser and material properties on efficient, high-resolution hydrogel degradation are discussed and the current application space in cell and tissue engineering is reviewed. This review aims to acquaint readers with the capability and uses of laser-based degradation of biomaterials, so that it may be easily and widely adopted.

Laser surface modification of AZ31B Mg alloy for bio-wettability

Magnesium alloys are the potential degradable materials for load-bearing implant application due to their comparable mechanical properties to human bone, excellent bioactivity, and in vivo non-toxicity. However, for a successful load-bearing implant, the surface of bio-implant must allow protein absorption and layer formation under physiological environment that can assist the cell/osteoblast growth. In this regard, surface wettability of bio-implant plays a key role to dictate the quantity of protein absorption. In light of this, the main objective of the present study was to produce favorable bio-wettability condition of AZ31B Mg alloy bio-implant surface via laser surface modification technique under various laser processing conditions. In the present efforts, the influence of laser surface modification on AZ31B Mg alloy surface on resultant bio-wettability was investigated via contact-angle measurements and the co-relationships among microstructure (grain size), surface roughness, surface energy, and surface chemical composition were established. In addition, the laser surface modification technique was simulated by computational (thermal) model to facilitate the prediction of temperature and its resultant cooling/solidification rates under various laser processing conditions for correlating with their corresponding composition and phase evolution. These predicted thermal properties were later used to correlate with the corresponding microstructure, chemical composition, and phase evolution via experimental analyses (X-ray diffractometer, scanning electron microscope, energy-dispersive spectroscopy).

Bioinspired wetting surface via laser microfabrication

Bioinspired special wettibilities including superhydrophobicity and tunable adhesive force have drawn considerable attention because of their significant potential for fundamental research and practical applications. This review summarizes recent progress in the development of bioinspired wetting surfaces via laser microfabrication, with a focus on controllable, biomimetic, and switchable wetting surfaces, as well as their applications in biology, microfluidic, and paper-based devices, all of which demonstrate the ability of laser microfabrication in producing various multiscale structures and its adaptation in a great variety of materials. In particular, compared to other techniques, laser microfabrication can realize special modulation ranging from superhydrophilic to superhydrophobic without the assistance of fluorination, allowing much more freedom to achieve complex multiple-wettability integration. The current challenges and future research prospects of this rapidly developing field are also being discussed. These approaches open the intriguing possibility of the development of advanced interfaces equipped with the integration of more functionalities.

Tissue growth into three-dimensional composite scaffolds with controlled micro-features and nanotopographical surfaces

Controlling topographic features at all length scales is of great importance for the interaction of cells with tissue regenerative materials. We utilized an indirect three-dimensional printing method to fabricate polymeric scaffolds with pre-defined and controlled external and internal architecture that had an interconnected structure with macro- (400-500 μm) and micro- (∼25 μm) porosity. Polycaprolactone (PCL) was used as model system to study the kinetics of tissue growth within porous scaffolds. The surface of the scaffolds was decorated with TiO2 and bioactive glass (BG) nanoparticles to the better match to nanoarchitecture of extracellular matrix (ECM). Micrometric BG particles were also used to reveal the effect of particle size on the cell behavior. Observation of tissue growth and enzyme activity on two-dimensional (2D) films and three-dimensional (3D) scaffolds showed effects of nanoparticle inclusion and of surface curvature on the cellular adhesion, proliferation, and kinetics of preosteoblastic cells (MC3T3-E1) tissue growth into the pore channels. It was found that the presence of nanoparticles in the substrate impaired cellular adhesion and proliferation in 3D structures. Evaluation of alkaline phosphate activity showed that the presence of the hard particles affects differentiation of the cells on 2D films. Notwithstanding, the effect of particles on cell differentiation was not as strong as that seen by the curvature of the substrate. We observed different effects of nanofeatures on 2D structures with those of 3D scaffolds, which influence the cell proliferation and differentiation for non-load-bearing applications in bone regenerative medicine.

Laser surface modification for synthesis of textured bioactive and biocompatible Ca-P coatings on Ti-6Al-4V

A textured calcium phosphate based bio-ceramic coating was synthesized by continuous wave Nd:YAG laser induced direct melting of hydroxyapatite precursor on Ti-6Al-4V substrate. Two different micro-textured patterns (100 μm and 200 μm line spacing) of Ca-P based phases were fabricated by this technique to understand the alignment and focal adhesion of the bone forming cells on these surfaces. X-ray diffraction studies of the coated samples indicated the presence of CaTiO₃, α-Ca₃(PO₄)₂, Ca(OH)₂, TiO₂ (anatase) and TiO₂ (rutile) phases as a result of the intermixing between the precursor and substrate material during laser processing. A two dimensional elemental mapping of the cross-section of the coated samples exhibited the presence of higher phosphorous concentration within the coating and a thin layer of calcium concentration only at the top of the coating. Improved in vitro bioactivity and in vitro biocompatibility was observed for the laser processed samples as compared to the control.