A Fully Three-Dimensional Printed Inchworm-Inspired Soft Robot with Magnetic Actuation

Multifunctional Fiber Robotics with Low Mechanical Hysteresis for Magnetic Navigation and Inhaled Gas Sensing

Recently, increasing research attention has been directed toward detecting the distribution of hazardous gases in the respiratory system for potential diagnosis and treatment of lung injury. Among various technologies, magnetic fiber robots exhibit great potential for minimally invasive surgery and in situ disease diagnosis. However, integrating magnetic fibers with functionalized sensitive materials remains challenging while preserving the miniaturized fibers' mechanical properties. Herein, we report Ti3C2Tx/TPU/NdFeB fibers prepared by facile wet spinning, spray coating, and magnetization, obtaining fibers with decent strength (4.34 MPa) and low hysteresis while maintaining mechanical robustness and magnetoelectric properties. Such fiber robotics could be magnetically actuated for complex movement, while the surface-coated MXene endowed them with the specific response of 5.2% to 40 ppm of triethylamine gas. Fiber robotics realized magnetically driven omnidirectional steering and navigation for propulsion in tubular environments by combination with nitinol guide wires. Consequently, based on magnetic navigation and the chemiresistive gas response, the proposed fiber robotics could locate the position with the highest level of the triethylamine gas inside a bronchial model and provide information on its distribution. This provides a proof-of-concept demonstration for inhaled hazardous gas detection and minimally invasive robotic surgery by multifunctional fiber robotics.

3D Printed Magnetic Bionic Robot Inspired by Octopus for Drug Transportation

The octopus has attracted widespread attention owing to its unique underwater movement and its ability to escape with inkjets, which also promoted the development of underwater bionic robots. This study introduces a magnetic octopus robot (MOR) 3D printed with PA6/NdFeB composite material, which has good magnetic responsiveness and rigidity to cope with complex environments. The MOR can roll and rotate through complex terrain and passages because of its eight-claw structure. It also has amphibious locomotion and can pass through narrow gaps of 37.5% of its height by deformation. In addition, the MOR can not only clamp, transport, and release solids but also liquids by adding silicone hollow spheres, which indicates the potential of the MOR to be used in medical applications for transporting solid or liquid drugs. This research will help broaden the application prospects of magnetron robots in the field of medical drug transportation.

A Proprioceptive Janus Fiber with Controllable Multistage Segments for Bionic Soft Robots

Smart fibers capable of integrating the multifunctionality of actuation and self-sensation into a single proprioceptive device have significant applications in soft robots and biomedicine. Especially, the achievement of self-sensing the movement patterns of different actuating segments in one fiber is still a great challenge. Herein, in this study, a fiber with the controllable Janus architecture is successfully proposed via an artful centrifugation-driven hierarchical gradient self-assembly strategy, which couples two functional components of piezoresistive carbon nanotubes and magnetic NdFeB nanoparticles into the upper and lower layers of this flexible fibrous framework with the porous sponge structure partially, respectively. As predicted, the final product exhibits the as-anticipated bionic proprioceptive behaviors of programmable actuating deformation and highly selective response to bending, stretching, and pressure with high washable stability and mechanical performances. More importantly, assisted by the different three-dimensional printing molds, the superlong Janus fibers with various controllable lengths of the reversed but sequential multistage segments can be fabricated, offering the hybrid magnetic actuation and proprioceptive sensation existing at arbitrary nodes. Therefore, several kinds of soft organism-inspired Janus fiber-derived soft robots with the arbitrarily controlled segmental characters were assembled as the proof-of-concept, which can not only realize a snake or inchworm-inspired successive contracting-stretching deformation and a sperm-inspired self-rotating crawling motion but also self-sense the signals of each segment themselves in real time and then be used to navigate an object to target position in a liquid-filled confined tube. It is believed that this work promotes the further development of proprioceptive soft robots.

Untethered bistable origami crawler for confined applications

Magnetically actuated miniature origami crawlers are capable of robust locomotion in confined environments but are limited to passive functionalities. Here, we propose a bistable origami crawler that can shape-morph to access two separate regimes of folding degrees of freedom that are separated by an energy barrier. Using the modified bistable V-fold origami crease pattern as the fundamental unit of the crawler, we incorporated internal permanent magnets to enable untethered shape-morphing. By modulating the orientation of the external magnetic field, the crawler can reconfigure between an undeployed locomotion state and a deployed load-bearing state. In the undeployed state, the crawler can deform to enable out-of-plane crawling for robust bi-directional locomotion and navigation in confined environments based on friction anisotropy. In the deployed state, the crawler can execute microneedle insertion in confined environments. Through this work, we demonstrated the advantage of incorporating bistability into origami mechanisms to expand their capabilities in space-constraint applications.

Untethered soft actuators for soft standalone robotics

Soft actuators produce the mechanical force needed for the functional movements of soft robots, but they suffer from critical drawbacks since previously reported soft actuators often rely on electrical wires or pneumatic tubes for the power supply, which would limit the potential usage of soft robots in various practical applications. In this article, we review the new types of untethered soft actuators that represent breakthroughs and discuss the future perspective of soft actuators. We discuss the functional materials and innovative strategies that gave rise to untethered soft actuators and deliver our perspective on challenges and opportunities for future-generation soft actuators.

Rotini-like MXene@LCE Actuator with Diverse and Programmable Actuation Based on Dual-mode Synergy

Liquid crystalline elastomer (LCE) exhibits muscle-like actuation upon order-disturbed stimulus, offering ample room for designing soft robotic systems. Multimodal LCE is demonstrated to unleash the potential to perform multitasks. However, each actuation mode is typically isolated. In contrast, coordination between different actuation modes based on an MXene-doped LCE is realized, whose actuation can be triggered either by directly heating/cooling or using near-infrared light due to the photo-thermal effect of MXene. As such, the two activation modes (heat and light) not only can work individually to offer stable actuation under different conditions but also can collaborate synergistically to generate more intelligent motions, such as achieving the brake and turn of an autonomous rolling. The principle therefore can diversify the design principles for multifunctional soft actuators and robotics.

Piezo-Wormbots for Continuous Crawling

Biomimetic soft robots are typically made of soft materials with bioinspired configurations. However, their locomotion is activated and manipulated by externally controlled soft actuators. In this study, piezo-wormbots were developed by automatically triggering the mechanical metamaterial-inspired soft actuator to mimic the continuous crawling of inchworms without manipulation, where crawling was controlled by the deformation of the piezo-wormbots themselves. We designed the flexible piezo-wormbots with an actuator to generate bending deformation under continuous inflation, piezoelectric rubber to automatically create internal excitation voltage to trigger deflation, as well as true legs and prolegs to convert the bending-recovering sequence into continuous crawling. We tailored the actuator to enhance the crawling performance and found that the response was critically affected by the leg pattern, inflation-to-deflation time duration ratio, air pressure, and ground environment. We observed satisfactory locomotion performance for the following tasks (pushing boxes and approaching a predefined target) through accurate self-actuated crawling under up to 51 continuous bending cycles. The maximum crawling velocity of the piezo-wormbots was found to be 16.6 mm/s, resulting in a maximum body length per second (BL/s) of 0.13, which is comparable to those of most natural inchworms (0.1-0.3 BL/s). This study offers new insight into bioinspired soft robotics and expands its biomimetic performance to continuously autonomous locomotion.

Metachronal Motion of Biological and Artificial Cilia

Cilia are slender, hair-like cell protrusions that are present ubiquitously in the natural world. They perform essential functions, such as generating fluid flow, propulsion, and feeding, in organisms ranging from protozoa to the human body. The coordinated beating of cilia, which results in wavelike motions known as metachrony, has fascinated researchers for decades for its role in functions such as flow generation and mucus transport. Inspired by nature, researchers have explored diverse materials for the fabrication of artificial cilia and developed several methods to mimic the metachronal motion observed in their biological counterparts. In this review, we will introduce the different types of metachronal motion generated by both biological and artificial cilia, the latter including pneumatically, photonically, electrically, and magnetically driven artificial cilia. Furthermore, we review the possible applications of metachronal motion by artificial cilia, focusing on flow generation, transport of mucus, particles, and droplets, and microrobotic locomotion. The overall aim of this review is to offer a comprehensive overview of the metachronal motions exhibited by diverse artificial cilia and the corresponding practical implementations. Additionally, we identify the potential future directions within this field. These insights present an exciting opportunity for further advancements in this domain.

A Versatile Topology-Optimized Compliant Actuator for Soft Robotic Gripper and Walking Robot

The remarkable interaction capabilities of soft robots within various environments have captured substantial attention from researchers. In recent years, bionics has provided a rich inspiration for the design of soft robots. Nevertheless, predicting the locomotion of soft actuators and determining material layouts solely based on intuition or experience remain a formidable challenge. Previous actuators predominantly targeted separate applications, leading to elevated costs and diminished interchangeability. The objective of this article is to extract the common requirements of diverse application domains and develop a versatile compliant actuator. A mathematical model of the compliant mechanism is proposed under the framework of topology optimization, resulting in an optimal distribution of both structure and material. Through comparison with empirical and semioptimal designs, the results show that the proposed versatile actuator has the advantages of both stiffness and flexibility. We propose an associative design strategy for soft grippers and walking robots. The soft gripper can perfectly complete adaptive grasping of objects with varying sizes, shapes, and masses. The successful in-water gripping experiment underscores the robust cross-medium operational capabilities of the soft gripper. Notably, our experimental results show that the walking robot can move quickly for 5 cycles in 8.25 s and can guarantee the control accuracy of continuous motion. Moreover, the robot swiftly switches walking directions within a mere 0.45 s. The optimization and design strategy presented in this article can furnish novel insights for shaping the next generation of soft robots.

Advancements in materials, manufacturing, propulsion and localization: propelling soft robotics for medical applications

Soft robotics is an emerging field showing immense potential for biomedical applications. This review summarizes recent advancements in soft robotics for in vitro and in vivo medical contexts. Their inherent flexibility, adaptability, and biocompatibility enable diverse capabilities from surgical assistance to minimally invasive diagnosis and therapy. Intelligent stimuli-responsive materials and bioinspired designs are enhancing functionality while improving biocompatibility. Additive manufacturing techniques facilitate rapid prototyping and customization. Untethered chemical, biological, and wireless propulsion methods are overcoming previous constraints to access new sites. Meanwhile, advances in tracking modalities like computed tomography, fluorescence and ultrasound imaging enable precision localization and control enable in vivo applications. While still maturing, soft robotics promises more intelligent, less invasive technologies to improve patient care. Continuing research into biocompatibility, power supplies, biomimetics, and seamless localization will help translate soft robots into widespread clinical practice.

Magnetic Microrobots Fabricated by Photopolymerization and Assembly

Magnetic soft microrobots have great potential to access narrow spaces and conduct multiple tasks in the biomedical field. Until now, drug delivery, microsurgery, disease diagnosis, and dredging the blocked blood vessel have been realized by magnetic soft microrobots in vivo or in vitro. However, as the tasks become more and more complex, more functional units have been embedded in the body of the developed magnetic microrobots. These magnetic soft microrobots with complex designed geometries, mechanisms, and magnetic orientation are now greatly challenging the fabrication of the magnetic microrobots. In this paper, we propose a new method combining photopolymerization and assembly for the fabrication of magnetic soft microrobots. Utilizing the micro-hand assembly system, magnetic modules with different shapes and materials are firstly arrayed with precise position and orientation control. Then, the developed photopolymerization system is employed to fix and link these modules with soft materials. Based on the proposed fabrication method, 3 kinds of soft magnetic microrobots were fabricated, and the fundamental locomotion was presented. We believe that the presented fabrication strategy could help accelerate the clinical application of magnetic microrobots.

Numerical Study of Metachronal Wave-Modulated Locomotion in Magnetic Cilia Carpets

Metachronal motions are ubiquitous in terrestrial and aquatic organisms and have attracted substantial attention in engineering for their potential applications. Hard-magnetic soft materials are shown to provide new opportunities for metachronal wave-modulated robotic locomotion by multi-agent active morphing in response to external magnetic fields. However, the design and optimization of such magnetic soft robots can be complex, and the fabrication and magnetization processes are often delicate and time-consuming. Herein, a computational model is developed that integrates granular models into a magnetic-lattice model, both of which are implemented in the highly efficient parallel computing platform large-scale atomic/molecular massively parallel simulator (LAMMPS). The simulations accurately reproduce the deformation of single cilium, the metachronal wave motion of multiple cilia, and the crawling and rolling locomotion of magnetic cilia soft robots. Furthermore, the simulations provide insight into the spatial and temporal variation of friction forces and trajectories of cilia tips. The results contribute to the understanding of metachronal wave-modulated locomotion and potential applications in the field of soft robotics and biomimetic engineering. The developed model also provides a versatile computational framework for simulating the movement of magnetic soft robots in realistic environments and has the potential to guide the design, optimization, and customization of these systems.

Physically intelligent autonomous soft robotic maze escaper

Autonomous maze navigation is appealing yet challenging in soft robotics for exploring priori unknown unstructured environments, as it often requires human-like brain that integrates onboard power, sensors, and control for computational intelligence. Here, we report harnessing both geometric and materials intelligence in liquid crystal elastomer-based self-rolling robots for autonomous escaping from complex multichannel mazes without the need for human-like brain. The soft robot powered by environmental thermal energy has asymmetric geometry with hybrid twisted and helical shapes on two ends. Such geometric asymmetry enables built-in active and sustained self-turning capabilities, unlike its symmetric counterparts in either twisted or helical shapes that only demonstrate transient self-turning through untwisting. Combining self-snapping for motion reflection, it shows unique curved zigzag paths to avoid entrapment in its counterparts, which allows for successful self-escaping from various challenging mazes, including mazes on granular terrains, mazes with narrow gaps, and even mazes with in situ changing layouts.

Effect of microstructure evolution on the mechanical behavior of magneto-active elastomers with different matrix stiffness

Evolution of microstructure in magneto-active elastomers (MAEs) which can be caused by an applied magnetic field is a fascinating phenomenon with a significant impact on the mechanical behavior of the composite. To gain insight into the underlying mechanisms of this phenomenon, it is essential to create a model that can appropriately describe the field induced change in the particle distribution and its mechanical implications. The magneto-mechanical coupling is driven by magnetic interactions between the particles in the applied field. These magnetic interactions can result in macroscopic deformation of the sample and also in rearrangement of the microstructure, i.e. the local positions of the particles. In the case of initially isotropic MAEs made with a sufficiently soft matrix, this leads to the formation of chains of magnetized particles, creating a significant increase in the mechanical moduli along the field direction. In this paper, we implement a transversely isotropic Neo-Hookean material model to account for such anisotropic elastic behavior. A dipolar mean field approach is used to describe magnetic interactions between the particles. A penalty term is introduced to compensate for the micro-mechanical elastic energy required to move the particles inside the cross-linked elastomer. The resulting model can predict the huge magneto-rheological effects observed in experiments, and improves our understanding of how microstructure evolution affects magnetically induced deformation and stiffness of MAEs.

A Multipole Magnetoactive Elastomer for Vibration-Driven Locomotion

Smart materials such as magnetoactive elastomers (MAEs) combine elastic and magnetic properties that can be significantly changed in response to a magnetic field and therefore offer enormous potential for applications in both scientific research and engineering. When such an elastomer contains microsized hard magnetic particles, it can become an elastic magnet once magnetized in a strong magnetic field. This article studies a multipole MAE with the aim of utilizing it as an actuation element of vibration-driven locomotion robots. The elastomer beam has three magnetic poles overall with the same poles at the ends and possesses silicone bristles protruding from its underside. The quasi-static bending of the multipole elastomer in a uniform magnetic field is investigated experimentally. The theoretical model exploits the magnetic torque to describe the field-induced bending shapes. The unidirectional locomotion of the elastomeric bristle-bot is realized in two prototype designs using magnetic actuation of either an external or an integrated source of an alternating magnetic field. The motion principle is based on cyclic interplay of asymmetric friction and inertia forces caused by field-induced bending vibrations of the elastomer. The locomotion behavior of both prototypes shows a strong resonant dependency of the advancing speed on the frequency of applied magnetic actuation.

Soft Multimaterial Magnetic Fibers and Textiles

Magnetically responsive soft materials are promising building blocks for the next generation of soft robotics, prosthesis, surgical tools, and smart textiles. To date, however, the fabrication of highly integrated magnetic fibers with extreme aspect ratios, that can be used as steerable catheters, endoscopes, or within functional textiles remains challenging. Here, multimaterial thermal drawing is proposed as a material and processing platform to realize 10s of meters long soft, ultrastretchable, yet highly resilient magnetic fibers. Fibers with a diameter as low as 300 µm and an aspect ratio of 105 are demonstrated, integrating nanocomposite domains with ferromagnetic microparticles embedded in a soft elastomeric matrix. With the proper choice of filler content that must strike the right balance between magnetization density and mechanical stiffness, fibers withstanding strains of >1000% are shown, which can be magnetically actuated and lift up to 370 times their own weight. Magnetic fibers can also integrate other functionalities like microfluidic channels, and be weaved into conventional textiles. It is shown that the novel magnetic textiles can be washed and sustain extreme mechanical constraints, as well as be folded into arbitrary shapes when magnetically actuated, paving the way toward novel intriguing opportunities in medical textiles and soft magnetic systems.

Kirigami-Inspired 3D Printable Soft Pneumatic Actuators with Multiple Deformation Modes for Soft Robotic Applications

Soft robots have received much attention due to their impressive capabilities including high flexibility and inherent safety features for humans or unstructured environments compared with hard-bodied robots. Soft actuators are the crucial components of soft robotic systems. Soft robots require dexterous soft actuators to provide the desired deformation for different soft robotic applications. Most of the existing soft actuators have only one or two deformation modes. In this article, a new soft pneumatic actuator (SPA) is proposed taking inspiration from Kirigami. Kirigami-inspired cuts are applied to the actuator design, which enables the SPA to be equipped with multiple deformation modes. The proposed Kirigami-inspired soft pneumatic actuator (KiriSPA) is capable of producing bending motion, stretching motion, contraction motion, combined motion of bending and stretching, and combined motion of bending and contraction. The KiriSPA can be directly manufactured using 3D printers based on the fused deposition modeling technology. Finite element method is used to analyze and predict the deformation modes of the KiriSPA. We also investigated the step response, creep, hysteresis, actuation speed, stroke, workspace, stiffness, power density, and blocked force of the KiriSPA. Moreover, we demonstrated that KiriSPAs can be combined to expand the capabilities of various soft robotic systems including the soft robotic gripper for delicate object manipulation, the soft planar robotic manipulator for picking objects in the confined environment, the quadrupedal soft crawling robot, and the soft robot with the flipping locomotion.

A Magnetic Bio-Inspired Soft Carrier as a Temperature-Controlled Gastrointestinal Drug Delivery System

Currently, gastrointestinal bleeding in the colon wall and the small bowel is diagnosed and treated with endoscopes. However, the locations of this condition are often problematic to treat using traditional flexible and tethered tools. New studies commonly consider untethered devices for solving this problem. However, there still exists a gap in the extant literature, and more research is needed to diagnose and deliver drugs in the lower gastrointestinal tract using soft robotic carriers. This paper discusses the development of an untethered, magnetically-responsive bio-inspired soft carrier. A molding process is utilized to produce prototypes from Diisopropylidene-1,6-diphenyl-1,6-hexanediol-based Polymer with Ethylene Glycol Dimethacrylate (DiAPLEX) MP-3510 - a shape memory polymer with a low transition temperature to enable the fabrication of these carriers. The soft carrier design is validated through simulation results of deformation caused by magnetic elements embedded in the carrier in response to an external field. The thermal responsiveness of the fabricated prototype carriers is assessed ex vivo and in a phantom. The results indicate a feasible design capable of administering drugs to a target inside a phantom of a large intestine. The soft carrier introduces a method for the controlled release of drugs by utilizing the rubbery modulus of the polymer and increasing the recovery force through magnetic actuation.

Design of a Bio-Inspired Untethered Soft Octopodal Robot Driven by Magnetic Field

Inspired by insects in nature, an increasing number of soft robots have been proposed to mimic their locomotion patterns. As a wireless actuation method, the magnetic actuation technique has been widely applied to drive soft magnetic robots for diverse applications. Although recent works on soft materials have stimulated the development of soft robots, it is challenging to achieve the efficient movement of soft robots for in vivo biomedical application. Inspired by centipede locomotion, a soft octopodal robot is designed in this paper. The robot is fabricated by mixing magnetic particles with silicone polymers, which is then magnetized by a specific magnetic field. The prototypes can be actuated by an external magnetic field (5-8 mT) produced by custom-made electromagnetic coils. Experimental results show that the soft robot can move at a high speed in the range of 0.536-1.604 mm/s on different surfaces, including paper, wood, and PMMA. This indicates that the soft robot can achieve comparable speeds to other robots, while being driven by a lower magnitude, resulting in energy savings. Furthermore, it achieves a high speed of 0.823 mm/s on the surface of a pig colon. The fine capabilities of the soft robot in terms of crossing uneven biological surfaces and carrying external loads are demonstrated. The results indicate that the reported soft robot exhibits promising applications in the biomedical field.

Field-Controlled Microrobots Fabricated by Photopolymerization

Field-controlled microrobots have attracted extensive research in the biological and medical fields due to the prominent characteristics including high flexibility, small size, strong controllability, remote manipulation, and minimal damage to living organisms. However, the fabrication of these field-controlled microrobots with complex and high-precision 2- or 3-dimensional structures remains challenging. The photopolymerization technology is often chosen to fabricate field-controlled microrobots due to its fast-printing velocity, high accuracy, and high surface quality. This review categorizes the photopolymerization technologies utilized in the fabrication of field-controlled microrobots into stereolithography, digital light processing, and 2-photon polymerization. Furthermore, the photopolymerized microrobots actuated by different field forces and their functions are introduced. Finally, we conclude the future development and potential applications of photopolymerization for the fabrication of field-controlled microrobots.

Bio-inspired magnetic-driven folded diaphragm for biomimetic robot

Functional soft materials, exhibiting multiple types of deformation, have shown their potential/abilities to achieve complicated biomimetic behaviors (soft robots). Inspired by the locomotion of earthworm, which is conducted through the contraction and stretching between body segments, this study proposes a type of one-piece-mold folded diaphragm, consisting of the structure of body segments with radial magnetization property, to achieve large 3D and bi-directional deformation with inside-volume change capability subjected to the low homogeneous magnetically driving field (40 mT). Moreover, the appearance based on the proposed magnetic-driven folded diaphragm is able to be easily customized to desired ones and then implanted into different untethered soft robotic systems as soft drivers. To verify the above points, we design the diaphragm pump providing unique properties of lightweight, powerful output and rapid response, and the soft robot including the bio-earthworm crawling robot and swimming robot inspired by squid to exhibit the flexible and rapid locomotion excited by single homogeneous magnetic fields.

Design of a Magnetic Soft Inchworm Millirobot Based on Pre-Strained Elastomer with Micropillars

Rather than using longitudinal "muscle" as in biological inchworm, the existing magnetic active elastomer (MAE)-based inchworm robots utilize magnetic torque to pull and push the soft body, which hinders its locomotion mobility. In this paper, a new pre-strained MAE inchworm millirobot with micropillars is proposed. The pre-strained elastomer serves as a pre-load muscle to contract the soft body, and the micropillars act as tiny feet to anchor the body during the locomotion. The proposed magnetic inchworm robot features a simple fabrication process that does not require special magnetization equipment. For the first time, the pre-load muscle is introduced in the design of magnetic inchworm robots, making it more like a real inchworm in terms of locomotion mechanism. The locomotion principle and parametric design for the desired locomotion performance have been investigated. Experimental results show that the fabricated magnetic inchworm robot (size: 10 mm × 5 mm, micropillars length: 200 µm, and mass: 262 g) can locomote on a smooth acrylic surface (roughness of 0.3 µm) at the speed of 0.125 body lengths per second, which is comparable with the existing magnetic inchworm robots. Moreover, the locomotion capabilities of the inchworm robot on wet surfaces and inclined planes have been verified via experimental studies.

Recent Developments of Actuation Mechanisms for Continuum Robots: A Review

Traditional rigid robots face significant challenges in congested and tight environments, including bulky size, maneuverability, and safety limitations. Thus, soft continuum robots, inspired by the incredible capabilities of biological appendages such as octopus arms, starfish, and worms, have shown promising performance in complex environments due to their compliance, adaptability, and safety. Different actuation techniques are implemented in soft continuum robots to achieve a smoothly bending backbone, including cable-driven actuators, pneumatic actuators, and hydraulic actuation systems. However, designing and developing efficient actuation mechanisms, motion planning approaches, and control algorithms are challenging due to the high degree of redundancy and non-linearity of soft continuum robots. This article profoundly reviews the merits and drawbacks of soft robots' actuation systems concerning their applications to provide the readers with a brief review reference to explore the recent development of soft robots' actuation mechanisms technology. Moreover, the authors have surveyed the recent review studies in controller design of continuum robots as a guidance for future applications.

The Dynamic Mortise-and-Tenon Interlock Assists Hydrated Soft Robots Toward Off-Road Locomotion

Natural locomotion such as walking, crawling, and swimming relies on spatially controlled deformation of soft tissues, which could allow efficient interaction with the external environment. As one of the ideal candidates for biomimetic materials, hydrogels can exhibit versatile bionic morphings. However, it remains an enormous challenge to transfer these in situ deformations to locomotion, particularly above complex terrains. Herein, inspired by the crawling mode of inchworms, an isotropic hydrogel with thermoresponsiveness could evolve to an anisotropic hydrogel actuator via interfacial diffusion polymerization, further evolving to multisection structure and exhibiting adaptive deformation with diverse degrees of freedom. Therefore, a dynamic mortise-and-tenon interlock could be generated through the interaction between the self-deformation of the hydrogel actuator and rough terrains, inducing continual multidimensional locomotion on various artificial rough substrates and natural sandy terrain. Interestingly, benefiting from the powerful mechanical energy transfer capability, the crawlable hydrogel actuators could also be utilized as hydrogel motors to activate static cargos to overstep complex terrains, which exhibit the potential application of a biomimetic mechanical discoloration device. Therefore, we believe that this design principle and control strategy may be of potential interest to the field of deformable materials, soft robots, and biomimetic devices.

SofaGym: An Open Platform for Reinforcement Learning Based on Soft Robot Simulations

OpenAI Gym is one of the standard interfaces used to train Reinforcement Learning (RL) Algorithms. The Simulation Open Framework Architecture (SOFA) is a physics-based engine that is used for soft robotics simulation and control based on real-time models of deformation. The aim of this article is to present SofaGym, an open-source software to create OpenAI Gym interfaces, called environments, out of soft robot digital twins. The link between soft robotics and RL offers new challenges for both fields: representation of the soft robot in an RL context, complex interactions with the environment, use of specific mechanical tools to control soft robots, transfer of policies learned in simulation to the real world, etc. The article presents the large possible uses of SofaGym to tackle these challenges by using RL and planning algorithms. This publication contains neither new algorithms nor new models but proposes a new platform, open to the community, that offers non existing possibilities of coupling RL to physics-based simulation of soft robots. We present 11 environments, representing a wide variety of soft robots and applications; we highlight the challenges showcased by each environment. We propose methods of solving the task using traditional control, RL, and planning and point out research perspectives using the platform.

Bio-Inspired Micro- and Nanorobotics Driven by Magnetic Field

In recent years, there has been explosive growth in the number of investigations devoted to the development and study of biomimetic micro- and nanorobots. The present review is dedicated to novel bioinspired magnetic micro- and nanodevices that can be remotely controlled by an external magnetic field. This approach to actuate micro- and nanorobots is non-invasive and absolutely harmless for living organisms in vivo and cell microsurgery, and is very promising for medicine in the near future. Particular attention has been paid to the latest advances in the rapidly developing field of designing polymer-based flexible and rigid magnetic composites and fabricating structures inspired by living micro-objects and organisms. The physical principles underlying the functioning of hybrid bio-inspired magnetic miniature robots, sensors, and actuators are considered in this review, and key practical applications and challenges are analyzed as well.

Ingestible Functional Magnetic Robot with Localized Flexibility (MR-LF)

The integration of an ingestible dosage form with sensing, actuation, and drug delivery capabilities can enable a broad range of surgical-free diagnostic and treatment strategies. However, the gastrointestinal (GI) tract is a highly constrained and complex luminal construct that fundamentally limits the size of an ingestible system. Recent advancements in mesoscale magnetic crawlers have demonstrated the ability to effectively traverse complex and confined systems by leveraging magnetic fields to induce contraction and bending-based locomotion. However, the integration of functional components (e.g., electronics) in the proposed ingestible system remains fundamentally challenging. Herein, the creation of a centralized compartment in a magnetic robot by imparting localized flexibility (MR-LF) is demonstrated. The centralized compartment enables MR-LF to be readily integrated with modular functional components and payloads, such as commercial off-the-shelf electronics and medication, while preserving its bidirectionality in an ingestible form factor. The ability of MR-LF to incorporate electronics, perform drug delivery, guide continuum devices such as catheters, and navigate air-water environments in confined lumens is demonstrated. The MR-LF enables functional integration to create a highly-integrated ingestible system that can ultimately address a broad range of unmet clinical needs.

Aligned Magnetic Nanocomposites for Modularized and Recyclable Soft Microrobots

Creating reconfigurable and recyclable soft microrobots that can execute multimodal locomotion has been a challenge due to the difficulties in material processing and structure engineering at a small scale. Here, we propose a facile technique to manufacture diverse soft microrobots (∼100 μm in all dimensions) by mechanically assembling modular magnetic microactuators into different three-dimensional (3D) configurations. The module is composed of a cubic micropillar supported on a square substrate, both made of elastomer matrix embedded with prealigned magnetic nanoparticle chains. By directionally bonding the sides or backs of identical modules together, we demonstrate that assemblies from only two and four modules can execute a wide range of locomotion, including gripping microscale objects, crawling and crossing solid obstacles, swimming within narrow and tortuous microchannels, and rolling along flat and inclined surfaces, upon applying proper magnetic fields. The assembled microrobots can additionally perform pick-transfer-place and cargo-release tasks at the microscale. More importantly, like the game of block-building, the microrobots can be disassembled back to separate modules and then reassembled to other configurations as demanded. The present study not only provides a versatile and economic manufacturing technique for reconfigurable and recyclable soft microrobots, enabling unlimited design space for diverse robotic locomotion from limited materials and module structures, but also extends the functionality and dexterity of existing soft robots to microscale that should facilitate practical applications at such small scale.

An Insect-Inspired Terrains-Adaptive Soft Millirobot with Multimodal Locomotion and Transportation Capability

Inspired by the efficient locomotion of insects in nature, researchers have been developing a diverse range of soft robots with simulated locomotion. These robots can perform various tasks, such as carrying medicines and collecting information, according to their movements. Compared to traditional rigid robots, flexible robots are more adaptable and terrain-immune and can even interact safely with people. Despite the development of biomimetic principles for soft robots, how their shapes, morphology, and actuation systems respond to the surrounding environments and stimuli still need to be improved. Here, we demonstrate an insect-scale soft robot with multi-locomotion modes made by Ecoflex and magnetic particles, which can be actuated by a magnetic field. Our robot can realize four distinct gaits: horizontal tumbling for distance, vertical tumbling for height, imitation of gastropod writhing, and inchworm-inspired crawling for cargo delivery. The soft compliant structure and four locomotion modes make the robot ideal for maneuvering in congested or complex spaces. In addition to linear motion (~20 mm/s) and turning (50°/s) on a flat terrain, the robot can also maneuver on various surface conditions (such as gaps, smooth slopes, sand, muddy terrain, and water). These merits, together with the robot's high load-carrying capacity (5 times its weight), low cost, obstacle-crossing capability (as high as ~50% its length), and pressure resistance (70 kg), allow for a wide variety of applications.

Magnetic 3D-Printed Composites-Production and Applications

Three-dimensional printing enables building objects shaped with a large degree of freedom. Additional functionalities can be included by modifying the printing material, e.g., by embedding nanoparticles in the molten polymer feedstock, the resin, or the solution used for printing, respectively. Such composite materials may be stronger or more flexible, conductive, magnetic, etc. Here, we give an overview of magnetic composites, 3D-printed by different techniques, and their potential applications. The production of the feedstock is described as well as the influence of printing parameters on the magnetic and mechanical properties of such polymer/magnetic composites.

SpringWorm: A Soft Crawling Robot with a Large-Range Omnidirectional Deformable Rectangular Spring for Control Rod Drive Mechanism Inspection

In this article, a cable-driven elastic backbone worm-like robot (named "SpringWorm") of decimeter-level size is designed, which has high adaptability in crack inspection of the weld between reactor pressure vessel (RPV) and control rod drive mechanisms. The robot consists of a body that adopts a rectangular helix spring backbone driven by four cables and the flexible claws embedded with distributed electromagnets. Combining the omnidirectional deformation of the backbone and the passive deformation adsorption of the claws, the robot can achieve a variety of gaits. Based on the approaches of geometric analysis and transformation matrices of the coordinate frame, a kinematic model of the cable-driven backbone has been established. Moreover, a mechanical model considering the friction between the cable and the backbone has also been established. The top position and the bending angle of the backbone obtained by the theory, simulation, and experiment are in good agreement. In addition, the errors of the driving force between simulation and experimental results are also small. SpringWorm is 670 g, measures 206 × 65 × 75 mm, has a maximum speed of 8.9 mm/s, and has a maximum payload of 1 kg. The robot can climb over 2-cm-tall steps and 4-cm-deep ditches, and climb and turn on the vertical wall, on the pipe with a radius of 31 cm, and on the spherical surface of RPV.

A novel soft-rigid wheeled crawling robot with high payload and passing capability

Soft crawling robots have been significantly studied in recent decades. However, moving in amphibious environment, high payload capability, and passing through complex ground have always been challenges for soft crawling robots. For these problems, this article presents an amphibious soft-rigid wheeled crawling robot (SRWCR) consists of a soft-rigid body actuated by two soft pneumatic actuators (SPAs), four wheels, and four annular soft bladders (ASBs) as brakes. By programming the actuation sequences of the two SPAs and four ASBs, SRWCR can achieve two basic modes of locomotion: linear motion and turning. Based on the energy conservation law, we have developed analytical models to interpret the static actuation performance of SPA, including linear and bending deformations. Furthermore, with the help of fast response and waterproof of SPA and ASB, SRWCR can achieve a linear speed of 14.97 mm/s, a turning speed of 5.63°/s, and an underwater locomotion speed of 13 mm/s, which demonstrates the excellent locomotion performance of SRWCR in amphibious environment. In addition, SRWCR can also achieve multiple impressive functions, including carrying a payload of 2 kg at the moving speed of 11.18 mm/s, passing through various complex ground such as the grass ground and sand ground, and so on, obstacle navigation in confined space. Compared with the existing soft crawling robots, with the help of the soft-rigid body and wheeled structure, SRWCR has the best payload and passing capability, which indicates the potential advantage of SRWCR in the design of functional robots.

Submillimeter-scale multimaterial terrestrial robots

Robots with submillimeter dimensions are of interest for applications that range from tools for minimally invasive surgical procedures in clinical medicine to vehicles for manipulating cells/tissues in biology research. The limited classes of structures and materials that can be used in such robots, however, create challenges in achieving desired performance parameters and modes of operation. Here, we introduce approaches in manufacturing and actuation that address these constraints to enable untethered, terrestrial robots with complex, three-dimensional (3D) geometries and heterogeneous material construction. The manufacturing procedure exploits controlled mechanical buckling to create 3D multimaterial structures in layouts that range from arrays of filaments and origami constructs to biomimetic configurations and others. A balance of forces associated with a one-way shape memory alloy and the elastic resilience of an encapsulating shell provides the basis for reversible deformations of these structures. Modes of locomotion and manipulation span from bending, twisting, and expansion upon global heating to linear/curvilinear crawling, walking, turning, and jumping upon laser-induced local thermal actuation. Photonic structures such as retroreflectors and colorimetric sensing materials support simple forms of wireless monitoring and localization. These collective advances in materials, manufacturing, actuation, and sensing add to a growing body of capabilities in this emerging field of technology.

3D Printing Ultraflexible Magnetic Actuators via Screw Extrusion Method

Soft magnetic actuators with programmable structure design and controllable deformation ability based on 3D printing technology have attracted extensive attention. In this paper, a novel 3D printing strategy is developed to manufacture the ultraflexible magnetic actuator, in which the printed material is composed of magnetic particles and thermoplastic rubber materials. Different from the traditional fused deposition printing, this printing strategy introduces screw extrusion technology to the heating components of the printer to overcome the problem of filament buckling in the flexible material. Thus, the tensile modulus of the printed products can be reduced to as low as ≈2 MPa. Based on the above method, biomimetic magnetic actuators of the sucker and the pump are constructed for adhering and releasing object and pumping liquid. The contraction performance of the magnetic actuator is studied via a series of experiments and the magnetic field-induced deformation is analyzed by the multiphysics-based finite element model. This work proves that ultraflexible magnetic actuators fabricated by this 3D printing strategy show broad prospects in the fields of soft robotics and bionics.

Soft robotic origami crawler

Biomimetic soft robotic crawlers have attracted extensive attention in various engineering fields, owing to their adaptivity to different terrains. Earthworm-like crawlers realize locomotion through in-plane contraction, while inchworm-like crawlers exhibit out-of-plane bending-based motions. Although in-plane contraction crawlers demonstrate effective motion in confined spaces, miniaturization is challenging because of limited actuation methods and complex structures. Here, we report a magnetically actuated small-scale origami crawler with in-plane contraction. The contraction mechanism is achieved through a four-unit Kresling origami assembly consisting of two Kresling dipoles with two-level symmetry. Magnetic actuation is used to provide appropriate torque distribution, enabling a small-scale and untethered robot with both crawling and steering capabilities. The crawler can overcome large resistances from severely confined spaces by its anisotropic and magnetically tunable structural stiffness. The multifunctionality of the crawler is explored by using the internal cavity of the crawler for drug storage and release. The magnetic origami crawler can potentially serve as a minimally invasive device for biomedical applications.

A Shift from Efficiency to Adaptability: Recent Progress in Biomimetic Interactive Soft Robotics in Wet Environments

Research field of soft robotics develops exponentially since it opens up many imaginations, such as human-interactive robot, wearable robots, and transformable robots in unpredictable environments. Wet environments such as sea and in vivo represent dynamic and unstructured environments that adaptive soft robots can reach their potentials. Recent progresses in soft hybridized robotics performing tasks underwater herald a diversity of interactive soft robotics in wet environments. Here, the development of soft robots in wet environments is reviewed. The authors recapitulate biomimetic inspirations, recent advances in soft matter materials, representative fabrication techniques, system integration, and exemplary functions for underwater soft robots. The authors consider the key challenges the field faces in engineering material, software, and hardware that can bring highly intelligent soft robots into real world.

Electromagnetic Feet With Soft Toes for Adaptive, Versatile, and Stable Locomotion of an Inchworm-Inspired Pipe Crawling Robot

Feet play an important role in the adaptive, versatile, and stable locomotion of legged creatures. Accordingly, several robotic research studies have used biological feet as the inspiration for the design of robot feet in traversing complex terrains. However, so far, no robot feet can allow legged robots to adaptively, versatilely, and robustly crawl on various curved metal pipes, including flat surfaces for pipe inspection. To address this issue, we propose here a novel hybrid rigid-soft robot-foot design inspired by the leg morphology of an inchworm. The foot consists of a rigid section with an electromagnet and a soft toe covering for enhanced adhesion to a metal pipe. Finite element analysis , performed under different loading conditions, reveals that due to its compliance, the soft toe can undergo recoverable deformation with adaptability to various curved metal pipes and plain metal surfaces. We have successfully implemented electromagnetic feet with soft toes (EROFT) on an inchworm-inspired pipe crawling robot for adaptive, versatile, and stable locomotion. Foot-to-surface adaptability is provided by the inherent elasticity of the soft toe, making the robot a versatile and stable metal pipe crawler. Experiments show that the robot crawling success rate reaches 100% on large diameter metal pipes. The proposed hybrid rigid-soft feet (i.e., electromagnetic feet with soft toes) can solve the problem of continuous surface adaptation for the robot in a stable and efficient manner, irrespective of the surface curvature, without the need to manually change the robot feet for specific surfaces. To this end, the foot development enables the robot to meet a set of deployment requirements on large oil and gas pipelines for potential use in inspecting various faults and leakages.

A Twisted and Coiled Polymer Artificial Muscles Driven Soft Crawling Robot Based on Enhanced Antagonistic Configuration

Twisted and coiled polymer (TCP) actuators are becoming increasingly prevalent in soft robotic fields due to their powerful and hysteresis-free stroke, large specific work density, and ease of fabrication. This paper presents a soft crawling robot with spike-inspired robot feet which can deform and crawl like an inchworm. The robot mainly consists of two leaf springs, connection part, robot feet, and two TCP actuators. A system level model of a soft crawling robot is presented for flexible and effective locomotion. Such a model can offer high-efficiency design and flexible locomotion of the crawling robot. Results show that the soft crawling robot can move at a speed of 0.275 mm/s when TCP is powered at 24 V.

Terrain Adaptability and Optimum Contact Stiffness of Vibro-bot with Arrayed Soft Legs

The terrain adaptability of the state-of-the-art robot is far behind natural animals, partly because of limited sensing, intelligence, controlling, and actuating ability. One possible solution is to explore the flexible locomotion structure and locomotion mode with good adaptability and fault tolerance. Based on this idea, we presented a type of vibro-bot with arrayed soft legs (VBASL) with excellent terrain adaptability by utilizing the rapid vibration of the soft belt array. With the resistance to local terrain blocking and combing the vibrational actuation, the VBASL has an advantage of multi-leg collaboration, so that very simple structure can achieve good terrain adaptability, such as steady locomotion on complex terrains like steep slope, ladders, steps, discrete pillars, and soft sands. Besides, the effects of soft leg geometry, stiffness, and ground topography on terrain adaptability and locomotion speed were also studied, indicating the similar contact stiffness to maximize the locomotion speed on different grounds. Then, a theoretical model was developed to describe the experiments well, which can guide the design of optimum contact stiffness of VBASL to achieve fast locomotion speed and good load capacity. By further modifying the robot structure, more practical functions such as turning, climbing, and anti-impacting were easily realized. The resistance to local terrain blocking and optimum contact stiffness are two important factors to improve the performance of VBASL, which may address the terrain adaptability challenge of robots working in practical unstructured environments.

3D Printing Polymeric Materials for Robots with Embedded Systems

The fabrication of robots and their embedded systems is challenging due to the complexity of the interacting components. The integration of additive manufacturing (AM) to robotics has made advancements in robotics manufacturing through sophisticated and state-of-the-art AM technologies and materials. With the emergence of 3D printing, 3D printing materials are also being considered and engineered for specific applications. This study reviews different 3D printing materials for 3D printing embedded robotics. Materials such as polyethylene glycol diacrylate (PEGDA), acrylonitrile butadiene styrene (ABS), flexible photopolymers, silicone, and elastomer-based materials were found to be the most used 3D printing materials due to their suitability for robotic applications. This review paper revealed that the key areas requiring more research are material formulations for improved mechanical properties, cost, and the inclusion of materials for specific applications. Future perspectives are also provided.

Monolithic processing of a layered flexible robotic actuator film for kinetic electronics

Low-invasive soft robotic techniques can potentially be used for developing next-generation body-machine interfaces. Most soft robots require complicated fabrication processes involving 3D printing and bonding/assembling. In this letter, we describe a monolithic soft microrobot fabrication process for the mass production of soft film robots with a complex structure by simple 2D processing of a robotic actuator film. The 45 µg/mm² lightweight film robot can be driven at a voltage of CMOS compatible 5 V with 0.15 mm^-1 large curvature changes; it can generate a force 5.7 times greater than its self-weight. In a durability test, actuation could be carried out over 8000 times without degradation. To further demonstrate this technique, three types of film robots with multiple degrees of freedom and a moving illuminator robot were fabricated. This technique can easily integrate various electrical circuits developed in the past to robotic systems and can be used for developing advanced wearable sensing devices; it can be called "Kinetic electronics".

Bioinspired soft microrobots actuated by magnetic field

In contrast to traditional large-scale robots, which require complicated mechanical joints and material rigidity, microrobots made of soft materials have exhibited amazing features and great potential for extensive applications, such as minimally invasive surgery. However, microrobots are faced with energy supply and control issues due to the miniaturization. Magnetic field actuation emerges as an appropriate approach to tackle with these issues. This review summarizes the latest progress of biomimetic soft microrobots actuated by magnetic field. Starting with an overview of the soft material and magnetic material adopted in the magnetic field actuated soft microrobots, the various fabrication methods and design structures of soft microrobots are summarized. Subsequently, practical and potential applications, such as targeted therapy, surgical operation, and the transportation of microscopic objects, in the fields of biomedicine and environmental remediation are presented. In the end, some current challenges, and the future development trends of magnetic soft microrobots are briefly discussed. This review is expected to offer a helpful guidance for the new researchers of biomimetic soft microrobots actuated by magnetic field.

Static Modeling of Soft Reinforced Bending Actuator Considering External Force Constraints

Soft robots are utilized in various operations such as rehabilitation, manipulation, and locomotion. These robots are sometimes excited by means of rubber based bending actuators, which are highly nonlinear and hyperelastic. In addition, in contrast to robots with rigid links and common actuators, continuous deformation of soft bending actuators in the presence of external forces makes the modeling more complicated. Thus, introducing a proper mathematical framework that accurately describes mechanical behavior of these actuators is still a challenge. In this research study, an analytical static model based on the Neo-Hookean material model is proposed. By resorting to the proposed model, a nonlinear relation between the actuator shape and inlet actuation pressure is extracted. Next, by means of the Euler-Bernoulli beam theory, the effect of external forces on the actuator configuration is investigated. Finally, experimental results are presented to validate the proposed theoretical model. In this regard, first, the actuator nonlinear behavior in a free motion is appropriately verified. Then, the actuator configuration, in the presence of two conventional external forces, called following and fixed direction, is analyzed.

3D Printing Magnetic Actuators for Biomimetic Applications

Biomimetic actuators with stimuli-responsiveness, adaptivity, and designability have attracted extensive attention. Recently, soft intelligent actuators based on stimuli-responsive materials have been gradually developed, but it is still challenging to achieve various shape manipulations of actuators through a simple 3D printing technology. In this paper, a 3D printing strategy based on magneto-active materials is developed to manufacture various biomimetic magnetic actuators, in which the new printable magnetic filament is composed of a thermoplastic rubber material and magnetic particles. The continuous shape transformation of magnetic actuators is further demonstrated to imitate the motion characteristic of creatures, including the predation behavior of octopus tentacles, the flying behavior of the butterfly, and the flower blooming behavior of the plant. Furthermore, the magnetic field-induced deformation of the biomimetic structure can be simulated by the finite element method, which can further guide the structural design of the actuators. This work proves that the biomimetic actuator based on soft magneto-active materials has the advantages of programmable integrated structure, rapid prototyping, remote noncontact actuation, and rapid magnetic response. As a result, this 3D printing method possesses broad application prospects in soft robotics and other fields.

Fabrication of Microfluidic Devices for Emulsion Formation by Microstereolithography

Droplet microfluidics—the art and science of forming droplets—has been revolutionary for high-throughput screening, directed evolution, single-cell sequencing, and material design. However, traditional fabrication techniques for microfluidic devices suffer from several disadvantages, including multistep processing, expensive facilities, and limited three-dimensional (3D) design flexibility. High-resolution additive manufacturing—and in particular, projection micro-stereolithography (PµSL)—provides a promising path for overcoming these drawbacks. Similar to polydimethylsiloxane-based microfluidics 20 years ago, 3D printing methods, such as PµSL, have provided a path toward a new era of microfluidic device design. PµSL greatly simplifies the device fabrication process, especially the access to truly 3D geometries, is cost-effective, and it enables multimaterial processing. In this review, we discuss both the basics and recent innovations in PµSL; the material basis with emphasis on custom-made photopolymer formulations; multimaterial 3D printing; and, 3D-printed microfluidic devices for emulsion formation as our focus application. Our goal is to support researchers in setting up their own PµSL system to fabricate tailor-made microfluidics.