Precision-Microfabricated Fiber-Optic Probe for Intravascular Pressure and Temperature Sensing

Scattering integral equation formulation for intravascular inclusion biosensing

A dielectric waveguide, inserted into blood vessels, supports its basic mode that is being scattered by a near-field intravascular inclusion. A rigorous integral equation formulation is performed and the electromagnetic response from that inhomogeneity is semi-analytically evaluated. The detectability of the formation, based on spatial distribution of the recorded signal, is estimated by considering various inclusion sizes, locations and textural contrasts. The proposed technique, with its variants and generalizations, provides a generic versatile toolbox to efficiently model biosensor layouts involved in healthcare monitoring and disease screening.

Fiber-Optic Intracranial Pressure Monitoring System Using Wi-Fi-An In Vivo Study

BACKGROUND

Continuous invasive monitoring of intracranial pressure (ICP) is essential in neurocritical care for surveillance and management of raised ICP. Fluid-based systems and strain gauge microsensors remain the current standard. In the past few decades, several studies with wireless monitoring were developed aiming to reduce invasiveness and complications.

OBJECTIVE

To describe a novel Wi-Fi fiber-optic device for continuous ICP monitoring using smartphone in a swine model.

METHODS

Two ICP sensors (wireless prototype and wire-based reference) were implanted in the cerebral parenchyma of a swine model for a total of 120 minutes of continuous monitoring. Every 5 minutes, jugular veins compression was performed to evaluate ICP changes. The experimentation was divided in 3 phases for comparison and analysis.

RESULTS

Phase 1 showed agreement in ICP changes for both sensors during jugular compression and releasing, with a positive and strong Spearman correlation (r = 0.829, P < .001). Phase 2 started after inversion of the sensors in the burr holes; there was a positive and moderately weak Spearman correlation (r = 0.262, P < .001). For phase 3, the sensors were returned to the first burr holes; the prototype behaved similarly to the reference sensor, presenting a positive and moderately strong Spearman correlation (r = 0.669, P < .001).

CONCLUSION

A Wi-Fi ICP monitoring system was demonstrated in a comprehensive and feasible way. It was possible to observe, using smartphone, an adequate correlation regarding ICP variations. Further adaptations are already being developed.

Multiphoton Nanosculpting of Optical Resonant and Nonresonant Microsensors on Fiber Tips

This work presents a multiphoton nanosculpting process that is employed to fabricate three-dimensional (3D) mechanically assisted optical resonant and nonresonant microsensors on fiber tips. The resonant microsensor consists of a complex 3D optical cavity design with submicron resolution and advanced micromechanical features including a hinged, multipositional mirror, a 3D spring body to displace this mirror without deforming it, and adhesive-retaining features for sealing the cavity. These features represent a breakthrough in the integration and fabrication capabilities of micro-optomechanical systems. The demonstrated dynamic optical surface enables directional thin-film deposition onto obscured areas. We leverage the rotation of the dynamically movable mirror to deposit a thin reflective coating onto the inner surfaces of a Fabry-Pérot cavity (FPC) with curved geometry. The reflective coating in conjunction with the dynamically rotatable mirror greatly improves the quality factor of the FPC and enables a new class of highly integrated multipurpose sensor systems. A unique spring body FPC on an optical fiber tip is used to demonstrate pressure sensing with a sensitivity of 38 ± 7 pm/kPa over a range of -80 to 345 kPa. The nonresonant microsensor consists of microblades that spin in response to an incident flow. Light exiting the core of the optical fiber is reflected back into the fiber core at a flow-dependent rate as the blades pass by. The fiber tip flow sensor operates successfully over a range of 9-25 LPM using nitrogen gas and achieves a linear response of 706 ± 43 reflections/LPM over a range of 10.9-12 LPM. The nanostructuring technology presented in this work offers a path forward for utilizing 3D design freedom in micromechanically enhanced optical and optofluidic systems to facilitate versatile processing and advantageous geometries beyond the current state-of-the-art.

The Current State of Optical Sensors in Medical Wearables

Optical sensors play an increasingly important role in the development of medical diagnostic devices. They can be very widely used to measure the physiology of the human body. Optical methods include PPG, radiation, biochemical, and optical fiber sensors. Optical sensors offer excellent metrological properties, immunity to electromagnetic interference, electrical safety, simple miniaturization, the ability to capture volumes of nanometers, and non-invasive examination. In addition, they are cheap and resistant to water and corrosion. The use of optical sensors can bring better methods of continuous diagnostics in the comfort of the home and the development of telemedicine in the 21st century. This article offers a large overview of optical wearable methods and their modern use with an insight into the future years of technology in this field.

Rapid Fabrication of Smooth Micro-Optical Components on Glass by Etching-Assisted Femtosecond Laser Modification

Femtosecond laser (fs-laser) is unfavorable in applications for the fabrication of micro-optical devices on hard materials owing to the problems of low fabrication efficiency and high surface roughness. Herein, a hybrid method combining fs-laser scanning, subsequent etching, and annealing was proposed to realize micro-optical devices with low roughness on glass. Compared to traditional laser ablation, the fabrication efficiency in this work was improved by one order of magnitude, and the surface roughness was decreased to 15 nm. Using this method, aspherical convex microlenses and spherical concave microlenses that possess excellent focusing and imaging properties are realized on photosensitive glass. The diameter and height of the microlenses were controlled by adjusting the fabrication parameters. These results indicate that the fs-laser-based hybrid method will open new opportunities for fabricating micro-optical components on hard materials.

Recent Advances in Biomedical Photonic Sensors: A Focus on Optical-Fibre-Based Sensing

In this invited review, we provide an overview of the recent advances in biomedical photonic sensors within the last five years. This review is focused on works using optical-fibre technology, employing diverse optical fibres, sensing techniques, and configurations applied in several medical fields. We identified technical innovations and advancements with increased implementations of optical-fibre sensors, multiparameter sensors, and control systems in real applications. Examples of outstanding optical-fibre sensor performances for physical and biochemical parameters are covered, including diverse sensing strategies and fibre-optical probes for integration into medical instruments such as catheters, needles, or endoscopes.

Fabrication and Qualitative Analysis of an Optical Fibre EFPI-Based Temperature Sensor

The following presents a comparison of an extrinsic Fabry–Perot interferometer (EFPI)-based temperature sensor, constructed using a novel diaphragm manufacturing technique, with a reference all-glass EFPI temperature sensor. The novel diaphragm was manufactured using polyvinyl alcohol (PVA). The novel sensor fabrication involved fusing a single-mode fibre (SMF) to a length of fused quartz capillary, which has an inner diameter of 132 μm and a 220 μm outer diameter. The capillary was subsequently polished until the distal face of the capillary extended approximately 60 μm beyond that of the single mode fibre. Upon completion of polishing, the assembly is immersed in a solution of PVA. Controlled extraction resulted in creation of a thin diaphragm while simultaneously applying a protective coating to the fusion point of the SMF and capillary. The EFPI sensor is subsequently sealed in a second fluid-filled capillary, thereby creating a novel temperature sensor structure. Both temperature sensors were placed in a thermogravimetric analyser and heated from an indicated 30 °C to 100 °C to qualitatively compare sensitivities. Initial results indicated that the novel manufacturing technique both expedited production and produces a more sensitive sensor when compared to an all-glass construction.