Evaluation of controllers for augmentative hip exoskeletons and their effects on metabolic cost of walking: explicit versus implicit synchronization

Background: Efficient gait assistance by augmentative exoskeletons depends on reliable control strategies. While numerous control methods and their effects on the metabolic cost of walking have been explored in the literature, the use of different exoskeletons and dissimilar protocols limit direct comparisons. In this article, we present and compare two controllers for hip exoskeletons with different synchronization paradigms. Methods: The implicit-synchronization-based approach, termed the Simple Reflex Controller (SRC), determines the assistance as a function of the relative loading of the feet, resulting in an emerging torque profile continuously assisting extension during stance and flexion during swing. On the other hand, the Hip-Phase-based Torque profile controller (HPT) uses explicit synchronization and estimates the gait cycle percentage based on the hip angle, applying a predefined torque profile consisting of two shorter bursts of assistance during stance and swing. We tested the controllers with 23 naïve healthy participants walking on a treadmill at 4 km ⋅ h-1, without any substantial familiarization. Results: Both controllers significantly reduced the metabolic rate compared to walking with the exoskeleton in passive mode, by 18.0% (SRC, p < 0.001) and 11.6% (HPT, p < 0.001). However, only the SRC led to a significant reduction compared to walking without the exoskeleton (8.8%, p = 0.004). The SRC also provided more mechanical power and led to bigger changes in the hip joint kinematics and walking cadence. Our analysis of mechanical powers based on a whole-body analysis suggested a reduce in ankle push-off under this controller. There was a strong correlation (Pearson's r = 0.778, p < 0.001) between the metabolic savings achieved by each participant with the two controllers. Conclusion: The extended assistance duration provided by the implicitly synchronized SRC enabled greater metabolic reductions compared to the more targeted assistance of the explicitly synchronized HPT. Despite the different assistance profiles and metabolic outcomes, the correlation between the metabolic reductions with the two controllers suggests a difference in individual responsiveness to assistance, prompting more investigations to explore the person-specific factors affecting assistance receptivity.

Control of a Back-Support Exoskeleton to Assist Carrying Activities

Back-support exoskeletons are commonly used in the workplace to reduce low back pain risk for workers performing demanding activities. However, for the assistance of tasks differing from lifting, back-support exoskeletons potential has not been exploited extensively. This work focuses on the use of an active back-support exoskeleton to assist carrying. A control strategy is designed that modulates the exoskeleton torques to comply with the task assistance requirements. In particular, two gait phase detection frameworks are exploited to adapt the exoskeleton assistance according to the legs' motion. The control strategy is assessed through an experimental analysis on ten subjects. Carrying task is performed without and with the exoskeleton assistance. Results prove the potential of the presented control in assisting the task without hindering the gait movement and improving the usability experienced by users. Moreover, the exoskeleton assistance significantly reduces the lumbar load associated with the task, demonstrating its promising use for risk mitigation in the workplace.

Real-Time Gait Phase and Task Estimation for Controlling a Powered Ankle Exoskeleton on Extremely Uneven Terrain

Positive biomechanical outcomes have been reported with lower-limb exoskeletons in laboratory settings, but these devices have difficulty delivering appropriate assistance in synchrony with human gait as the task or rate of phase progression change in real-world environments. This paper presents a controller for an ankle exoskeleton that uses a data-driven kinematic model to continuously estimate the phase, phase rate, stride length, and ground incline states during locomotion, which enables the real-time adaptation of torque assistance to match human torques observed in a multi-activity database of 10 able-bodied subjects. We demonstrate in live experiments with a new cohort of 10 able-bodied participants that the controller yields phase estimates comparable to the state of the art, while also estimating task variables with similar accuracy to recent machine learning approaches. The implemented controller successfully adapts its assistance in response to changing phase and task variables, both during controlled treadmill trials (N=10, phase RMSE: 4.8 ± 2.4%) and a real-world stress test with extremely uneven terrain (N=1, phase RMSE: 4.8 ± 2.7%).

Exoskeletal solutions to enable mobility with a lower leg fracture in austere environments

The treatment and evacuation of people with lower limb fractures in austere environments presents unique challenges that assistive exoskeletal devices could address. In these dangerous situations, independent mobility for the injured can preserve their vital capabilities so that they can safely evacuate and minimize the need for additional personnel to help. This expert view article discusses how different exoskeleton archetypes could provide independent mobility while satisfying the requisite needs for portability, maintainability, durability, and adaptability to be available and useful within austere environments. The authors also discuss areas of development that would enable exoskeletons to operate more effectively in these scenarios as well as preserve the health of the injured limb so that definitive treatment after evacuation will produce better outcomes.

Effects of Bilateral Assistance for Hemiparetic Gait Post-Stroke Using a Powered Hip Exoskeleton

Hemiparetic gait due to stroke is characterized by an asymmetric gait due to weakness in the paretic lower limb. These inter-limb asymmetries increase the biomechanical demand and reduce walking speed, leading to reduced community mobility and quality of life. With recent progress in the field of wearable technologies, powered exoskeletons have shown great promise as a potential solution for improving gait post-stroke. While previous studies have adopted different exoskeleton control methodologies for restoring gait post-stroke, the results are highly variable due to limited understanding of the biomechanical effect of exoskeletons on hemiparetic gait. In this study, we investigated the effect of different hip exoskeleton assistance strategies on gait function and gait biomechanics of individuals post-stroke. We found that, compared to walking without a device, powered assistance from hip exoskeletons improved stroke participants' self-selected overground walking speed by 17.6 ± 2.5% and 11.1 ± 2.7% with a bilateral and unilateral assistance strategy, respectively (p < 0.05). Furthermore, both bilateral and unilateral assistance strategies significantly increased the paretic and non-paretic step length (p < 0.05). Our findings suggest that powered assistance from hip exoskeletons is an effective means to increase walking speed post-stroke and tuning the balance of assistance between non-paretic and paretic limbs (i.e., a bilateral strategy) may be most effective to maximize performance gains.

Be Careful What You Wish for: Cost Function Sensitivity in Predictive Simulations for Assistive Device Design

Software packages that use optimization to predict the motion of dynamic systems are powerful tools for studying human movement. These “predictive simulations” are gaining popularity in parameter optimization studies for designing assistive devices such as exoskeletons. The cost function is a critical component of the optimization problem and can dramatically affect the solution. Many cost functions have been proposed that are biologically inspired and that produce reasonable solutions, but which may lead to different conclusions in some contexts. We used OpenSim Moco to generate predictive simulations of human walking using several cost functions, each of which produced a reasonable trajectory of the human model. We then augmented the model with motors that generated hip flexion, knee flexion, or ankle plantarflexion torques, and repeated the predictive simulations to determine the optimal motor torques. The model was assumed to be planar and bilaterally symmetric to reduce computation time. Peak torques varied from 41.3 to 79.0 N·m for the hip flexion motors, from 48.0 to 94.2 N·m for the knee flexion motors, and from 42.6 to 79.8 N·m for the ankle plantarflexion motors, which could have important design consequences. This study highlights the importance of evaluating the robustness of results from predictive simulations.

Modulating Multiarticular Energy during Human Walking and Running with an Unpowered Exoskeleton

Researchers have made advances in reducing the metabolic rate of both walking and running by modulating mono-articular energy with exoskeletons. However, how to modulate multiarticular energy with exoskeletons to improve the energy economy of both walking and running is still a challenging problem, due to the lack of understanding of energy transfer among human lower-limb joints. Based on the study of the energy recycling and energy transfer function of biarticular muscles, we proposed a hip-knee unpowered exoskeleton that emulates and reinforces the function of the hamstrings and rectus femoris in different gait phases. The biarticular exo-tendon of the exoskeleton assists hamstrings to recycle the kinetic energy of the leg swing while providing hip extension torque in the swing phase. In the following stance phase, the exo-tendon releases the stored energy to assist the co-contraction of gluteus maximus and rectus femoris for both hip extension and knee extension, thus realizing the phased modulation of hip and knee joint energy. The metabolic rate of both walking (1.5 m/s) and running (2.5 m/s) can be reduced by 6.2% and 4.0% with the multiarticular energy modulation of a hip-knee unpowered exoskeleton, compared to that of walking and running without an exoskeleton. The bio-inspired design method of this study may inspire people to develop devices that assist multiple gaits in the future.

Current developments of robotic hip exoskeleton toward sensing, decision, and actuation: A review

The aging population is now a global challenge, and impaired walking ability is a common feature in the elderly. In addition, some occupations such as military and relief workers require extra physical help to perform tasks efficiently. Robotic hip exoskeletons can support ambulatory functions in the elderly and augment human performance in healthy people during normal walking and loaded walking by providing assistive torque. In this review, the current development of robotic hip exoskeletons is presented. In addition, the framework of actuation joints and the high-level control strategy (including the sensors and data collection, the way to recognize gait phase, the algorithms to generate the assist torque) are described. The exoskeleton prototypes proposed by researchers in recent years are organized to benefit the related fields realizing the limitations of the available robotic hip exoskeletons, therefore, this work tends to be an influential factor with a better understanding of the development and state-of-the-art technology.

Analysis of the Bayesian Gait-State Estimation Problem for Lower-Limb Wearable Robot Sensor Configurations

Many exoskeletons today are primarily tested in controlled, steady-state laboratory conditions that are unrealistic representations of their real-world usage in which walking conditions (e.g., speed, slope, and stride length) change constantly. One potential solution is to detect these changing walking conditions online using Bayesian state estimation to deliver assistance that continuously adapts to the wearer's gait. This paper investigates such an approach in silico, aiming to understand 1) which of the various Bayesian filter assumptions best match the problem, and 2) which gait parameters can be feasibly estimated with different combinations of sensors available to different exoskeleton configurations (pelvis, thigh, shank, and/or foot). Our results suggest that the assumptions of the Extended Kalman Filter are well suited to accurately estimate phase, stride frequency, stride length, and ramp inclination with a wide variety of sparse sensor configurations.

Accurate Real-time Phase Estimation for Normal and Asymmetric Gait

An accurate real-time gait phase estimator for normal and asymmetric gait is developed by training and testing a time-delay neural network on gait data collected from six participants during treadmill walking. The trained model can generate smooth and highly accurate predictions of the gait phase with a root mean square error of less than 3.48% and 4.31% in normal and asymmetric gait, respectively. The coefficient of determination between the estimated and target phase is greater than 99% for all subjects with both normal and asymmetric gait. The proposed gait estimator also exhibits precise heel-strike event detection with an RMSE of 2.56% and 3.70% in normal and asymmetric gait, respectively. A spatial impedance controller is then employed and tested based on the estimated gait phase of a new participant. Obtained results confirm that the controller provided assistance in coordination with the user's motion both in normal and asymmetric gait conditions. The estimated gait phase is compared in the case of walking without and with the exoskeleton in passive and active modes, indicating persistent accuracy of the gait phase estimator regardless of the walking conditions.

Assistive Powered Hip Exoskeleton Improves Self-Selected Walking Speed in One Individual with Hemiparesis: A Case Study

Most individuals suffering a stroke have permanent weakness on one side of the body (hemiparesis) that reduces their ability to ambulate. Autonomous powered exoskeletons have been proposed as a possible solution to this problem. Studies with healthy subjects show that assistive powered exoskeletons have the potential to improve gait, for example, by reducing the metabolic cost of walking. However, only a handful of studies have been conducted with individuals with hemiparesis. Thus, the ability of autonomous exoskeletons to improve gait in this population remains largely unknown. In this study, we assess self-selected walking speed with and without an autonomous powered hip exoskeleton in one individual with hemiparesis walking on level ground. Results show that the proposed exoskeleton improves self-selected walking speed by ~30%. The biomechanical analysis suggest that the increased walking speed is the result of the powered hip exoskeleton enabling the subject to take longer strides on the hemiparetic side. This case study provides important information to inform future exoskeleton development and clinical study design.

Reducing the energy cost of walking with low assistance levels through optimized hip flexion assistance from a soft exosuit

As we age, humans see natural decreases in muscle force and power which leads to a slower, less efficient gait. Improving mobility for both healthy individuals and those with muscle impairments/weakness has been a goal for exoskeleton designers for decades. In this work, we discover that significant reductions in the energy cost required for walking can be achieved with almost 50% less mechanical power compared to the state of the art. This was achieved by leveraging human-in-the-loop optimization to understand the importance of individualized assistance for hip flexion, a relatively unexplored joint motion. Specifically, we show that a tethered hip flexion exosuit can reduce the metabolic rate of walking by up to 15.2 ± 2.6%, compared to locomotion with assistance turned off (equivalent to 14.8% reduction compared to not wearing the exosuit). This large metabolic reduction was achieved with surprisingly low assistance magnitudes (average of 89 N, ~ 24% of normal hip flexion torque). Furthermore, the ratio of metabolic reduction to the positive exosuit power delivered was 1.8 times higher than ratios previously found for hip extension and ankle plantarflexion. These findings motivated the design of a lightweight (2.31 kg) and portable hip flexion assisting exosuit, that demonstrated a 7.2 ± 2.9% metabolic reduction compared to walking without the exosuit. The high ratio of metabolic reduction to exosuit power measured in this study supports previous simulation findings and provides compelling evidence that hip flexion may be an efficient joint motion to target when considering how to create practical and lightweight wearable robots to support improved mobility.

Coordination Between Partial Robotic Exoskeletons and Human Gait: A Comprehensive Review on Control Strategies

Lower-limb robotic exoskeletons have become powerful tools to assist or rehabilitate the gait of subjects with impaired walking, even when they are designed to act only partially over the locomotor system, as in the case of unilateral or single-joint exoskeletons. These partial exoskeletons require a proper method to synchronize their assistive actions and ensure correct inter-joint coordination with the user’s gait. This review analyzes the state of the art of control strategies to coordinate the assistance provided by these partial devices with the actual gait of the wearers. We have analyzed and classified the different approaches independently of the hardware implementation, describing their basis and principles. We have also reviewed the experimental validations of these devices for impaired and unimpaired walking subjects to provide the reader with a clear view of their technology readiness level. Eventually, the current state of the art and necessary future steps in the field are summarized and discussed.

Simulating Ideal Assistive Strategies to Reduce the Metabolic Cost of Walking in the Elderly

OBJECTIVE

Development of walking assist exoskeletons is a growing area of study, offering a solution to restore, maintain, and enhance mobility. However, applying this technology to the elderly is challenging and there is currently no consensus as to the optimal strategy for assisting elderly gait. The gait patterns of elderly individuals often differ from those of the younger population, primarily in the ankle and hip joints. This study used musculoskeletal simulations to predict how ankle and hip actuators might affect the energy expended by elderly participants during gait.

METHODS

OpenSim was used to generate simulations of 10 elderly participants walking at self-selected slow, comfortable, and fast speeds. Ideal flexion/extension assistive actuators were added bilaterally to the ankle or hip joints of the models to predict the maximum metabolic power that could be saved by exoskeletons that apply torques at these joints.

RESULTS

Compared to the unassisted scenario, the use of ideal hip actuators resulted in 215%, 265%, and 306% reductions in average metabolic power consumption at slow, comfortable, and fast walking speeds, respectively; use of ideal ankle actuators resulted in 123%, 142%, and 161% metabolic savings, respectively.

CONCLUSION

The simulations suggest that providing hip assistance to elderly individuals during walking can result in significantly greater metabolic savings than ankle assistance, assuming kinematics and total joint moments do not change substantially with assistance.

SIGNIFICANCE

The achieved research results and analysis provide exoskeleton developers guidance on optimally designing walking assist exoskeletons, thus promoting consensus toward the optimal strategy for assisting elderly individuals.

Design and experimental testing of a force-augmenting exoskeleton for the human hand

Background

Many older Americans suffer from long-term upper limb dysfunction, decreased grip strength, and/or a reduced ability to hold objects due to injuries and a variety of age-related illnesses. The objective of this study was to design and build a five-fingered powered assistive exoskeleton for the human hand, and to validate its ability to augment the gripping and pinching efforts of the wearer and assist in performing ADLs.

Methods

The exoskeleton device was designed using CAD software and 3-D printed in ABS. Each finger’s movement efforts were individually monitored by a force sensing resistor at each fingertip, and proportionally augmented via the microcontroller-based control scheme, linear actuators, and rigid exoskeleton structure. The force production of the device and the force augmenting capability were assessed on ten healthy individuals with one 5-digit grasping test, three pinching tests, and two functional tests.

Results

Use of the device significantly decreased the forearm muscle activity necessary to maintain a grasping effort (67%, p < 0.001), the larger of two pinching efforts (30%, p < 0.05), and the palmer pinching effort (67%, p < 0.001); however, no benefit by wearing the device was identified while maintaining a minimal pinching effort or attempting one of the functional tests.

Conclusion

The exoskeleton device allowed subjects to maintain independent control of each digit, and while wearing the exoskeleton, in both the unpowered and powered states, subjects were able to grasp, hold, and move objects such as a water bottle, bag, smartphone, or dry-erase marker.

Efficacy of robotic exoskeleton for gait rehabilitation in patients with subacute stroke : a systematic review

BACKGROUND

Stroke is the most common cause of disability in Western Countries. It can lead to loss of mobility, capability to walk and ultimately loss of independence in activities of daily living (ADL). Several rehabilitative approaches have been proposed in these years. Robot-assisted gait rehabilitation (RAGT) plays a crucial role to perform a repetitive, intensive, and task-oriented treatment in stroke survivors. However, there are still few data on its role in subacute stroke patients.

AIM

The aim of the present study was to assess the efficacy of RAGT for gait recovery in subacute stroke survivors.

DESIGN

Systematic review with meta-analysis.

SETTING

The setting of the study included Units of Rehabilitation.

POPULATION

The analyzed population was represented by subacute stroke patients.

METHODS

PubMed, Scopus, Web of Science, CENTRAL, and PEDro were systematically searched until January 18, 2021, to identify randomized controlled trials (RCTs) presenting: stroke survivors in subacute phase (≤6 months) as participants; exoskeleton robots devices as intervention; conventional rehabilitation as a comparator; gait assessment, through qualitative scales, quantitative gait scales or quantitative parameters, as outcome measures. We also performed a meta-analysis of the mean difference in the functional ambulation category (FAC) via the random effect method.

RESULTS

Out of 3188 records, 14 RCTs were analyzed in this systematic review. The 14 studies have been published in the last 14 years (from 2006 to 2021) and included 576 stroke survivors, of which 306 received RAGT, and 270 underwent conventional rehabilitation. Lokomat robotic system was the most investigated robotic exoskeleton by the RCTs included (N.=9), albeit the meta-analysis demonstrated a non-significant difference of -0.09 in FAC (95% CI: -0.22.0.03) between Lokomat and conventional therapy. According to the PEDro scale, 11 (78.5%) were classified as good-quality studies, two as fair-quality studies (14.3%), and one as poor-quality study (7.1%).

CONCLUSIONS

Taken together, these findings showed that RAGT might have a potential role in gait recovery in subacute stroke survivors. However, further RCTs comparing the efficacy of RAGT with conventional physical therapy are still warranted in the neurorehabilitation field.

CLINICAL REHABILITATION IMPACT

This systematic review provides information on the efficacy of RAGT in allowing subacute stroke patients to perform high-intensity gait training with a lower physical burden on PRM professionals.

Comparing optimized exoskeleton assistance of the hip, knee, and ankle in single and multi-joint configurations

Exoskeletons that assist the hip, knee, and ankle joints have begun to improve human mobility, particularly by reducing the metabolic cost of walking. However, direct comparisons of optimal assistance of these joints, or their combinations, have not yet been possible. Assisting multiple joints may be more beneficial than the sum of individual effects, because muscles often span multiple joints, or less effective, because single-joint assistance can indirectly aid other joints. In this study, we used a hip-knee-ankle exoskeleton emulator paired with human-in-the-loop optimization to find single-joint, two-joint, and whole-leg assistance that maximally reduced the metabolic cost of walking. Hip-only and ankle-only assistance reduced the metabolic cost of walking by 26 and 30% relative to walking in the device unassisted, confirming that both joints are good targets for assistance (N = 3). Knee-only assistance reduced the metabolic cost of walking by 13%, demonstrating that effective knee assistance is possible (N = 3). Two-joint assistance reduced the metabolic cost of walking by between 33 and 42%, with the largest improvements coming from hip-ankle assistance (N = 3). Assisting all three joints reduced the metabolic cost of walking by 50%, showing that at least half of the metabolic energy expended during walking can be saved through exoskeleton assistance (N = 4). Changes in kinematics and muscle activity indicate that single-joint assistance indirectly assisted muscles at other joints, such that the improvement from whole-leg assistance was smaller than the sum of its single-joint parts. Exoskeletons can assist the entire limb for maximum effect, but a single well-chosen joint can be more efficient when considering additional factors such as weight and cost.

From a biological template model to gait assistance with an exosuit

The invention of soft wearable assistive devices, known as exosuits, introduced a new aspect in assisting unimpaired subjects. In this study, we designed and developed an exosuit with compliant biarticular thigh actuators called BATEX. Unlike the conventional method of using rigid actuators in exosuits, the BATEX is made of serial elastic actuators (SEA) resembling artificial muscles. This bioinspired design is complemented by the novel control concept of using the ground reaction force to adjust the artificial muscles' stiffness in the stance phase. By locking the motors in the swing phase, the SEAs will be simplified to passive biarticular springs, which is sufficient for leg swinging. The key concept in our design and control approach is to synthesize human locomotion to develop an assistive device instead of copying human motor control outputs. Analyzing human walking assistance using experiment-based OpenSim simulations demonstrates the advantages of the proposed design and control of BATEX, such as 9.4% reduction in metabolic cost during normal walking condition. This metabolic reduction increases to 10.4% when the subjects carry a 38 kg load. The adaptability of our proposed model-based control to such an unknown condition outperforms the assistance level of the model-free optimal controller. Moreover, increasing the assistive system's efficiency by adjusting the actuator compliance with the force feedback supports our previous findings on the LOPES II exoskeleton.

Robust Torque Predictions From Electromyography Across Multiple Levels of Active Exoskeleton Assistance Despite Non-linear Reorganization of Locomotor Output

Robotic exoskeletons can assist humans with walking by providing supplemental torque in proportion to the user's joint torque. Electromyographic (EMG) control algorithms can estimate a user's joint torque directly using real-time EMG recordings from the muscles that generate the torque. However, EMG signals change as a result of supplemental torque from an exoskeleton, resulting in unreliable estimates of the user's joint torque during active exoskeleton assistance. Here, we present an EMG control framework for robotic exoskeletons that provides consistent joint torque predictions across varying levels of assistance. Experiments with three healthy human participants showed that using diverse training data (from different levels of assistance) enables robust torque predictions, and that a convolutional neural network (CNN), but not a Kalman filter (KF), can capture the non-linear transformations in EMG due to exoskeleton assistance. With diverse training, the CNN could reliably predict joint torque from EMG during zero, low, medium, and high levels of exoskeleton assistance [root mean squared error (RMSE) below 0.096 N-m/kg]. In contrast, without diverse training, RMSE of the CNN ranged from 0.106 to 0.144 N-m/kg. RMSE of the KF ranged from 0.137 to 0.182 N-m/kg without diverse training, and did not improve with diverse training. When participant time is limited, training data should emphasize the highest levels of assistance first and utilize at least 35 full gait cycles for the CNN. The results presented here constitute an important step toward adaptive and robust human augmentation via robotic exoskeletons. This work also highlights the non-linear reorganization of locomotor output when using assistive exoskeletons; significant reductions in EMG activity were observed for the soleus and gastrocnemius, and a significant increase in EMG activity was observed for the erector spinae. Control algorithms that can accommodate spatiotemporal changes in muscle activity have broad implications for exoskeleton-based assistance and rehabilitation following neuromuscular injury.

A portable exotendon assisting hip and knee joints reduces muscular burden during walking

Assistive devices are used to reduce human effort during locomotion with increasing success. More assistance strategies are worth exploring, so we aimed to design a lightweight biarticular device with well-chosen parameters to reduce muscle effort. Based on the experience of previous success, we designed an exotendon to assist in swing leg deceleration. Then we conducted experiments to test the performance of the exotendon with different spring stiffness during walking. With the assistance of the exotendon, peak activation of semitendinosus decreased, with the largest reduction of 12.3% achieved with the highest spring stiffness (p = 0.004). The peak activations of other measured muscles were not significantly different (p = 0.15-0.92). The biological hip extension and knee flexion moments likewise significantly decreased with the spring stiffness (p < 0.01). The joint angle was altered during the assisted phases with decreased hip flexion and knee extension. Meanwhile, the step frequency and the step length were also altered, while the step width remained unaffected. Gait variability changed only in the frontal plane, exhibiting lower step width variability. We conclude that passive devices assisting hip extension and knee flexion can significantly reduce the burden on the hamstring muscles, while the kinematics is easily altered.

Powered hip exoskeleton improves walking economy in individuals with above-knee amputation

Above-knee amputation severely reduces the mobility and quality of life of millions of individuals. Walking with available leg prostheses is highly inefficient, and poor walking economy is a major problem limiting mobility. Here we show that an autonomous powered hip exoskeleton assisting the residual limb significantly improves metabolic walking economy by 15.6 ± 2.9% (mean ± s.e.m.; two-tailed paired t-test, P = 0.002) in six individuals with above-knee amputation walking on a treadmill. The observed metabolic cost improvement is equivalent to removing a 12-kg backpack from a nonamputee individual. All participants were able to walk overground with the exoskeleton, including starting and stopping, without notable changes in gait balance or stability. This study shows that assistance of the user's residual limb with a powered hip exoskeleton is a viable solution for improving amputee walking economy. By significantly reducing the metabolic cost of walking, the proposed hip exoskeleton may have a considerable positive impact on mobility, improving the quality of life of individuals with above-knee amputations.

Real-Time Gait Phase Estimation for Robotic Hip Exoskeleton Control During Multimodal Locomotion

We developed and validated a gait phase estimator for real-time control of a robotic hip exoskeleton during multimodal locomotion. Gait phase describes the fraction of time passed since the previous gait event, such as heel strike, and is a promising framework for appropriately applying exoskeleton assistance during cyclic tasks. A conventional method utilizes a mechanical sensor to detect a gait event and uses the time since the last gait event to linearly interpolate the current gait phase. While this approach may work well for constant treadmill walking, it shows poor performance when translated to overground situations where the user may change walking speed and locomotion modes dynamically. To tackle these challenges, we utilized a convolutional neural network-based gait phase estimator that can adapt to different locomotion mode settings to modulate the exoskeleton assistance. Our resulting model accurately predicted the gait phase during multimodal locomotion without any additional information about the user's locomotion mode, with a gait phase estimation RMSE of 5.04 ± 0.79%, significantly outperforming the literature standard (p < 0.05). Our study highlights the promise of translating exoskeleton technology to more realistic settings where the user can naturally and seamlessly navigate through different terrain settings.

Human biomechanics perspective on robotics for gait assistance: challenges and potential solutions

Technological advancements in robotic devices have the potential to transform human mobility through gait assistance. However, the integration of physical hardware and software control algorithms with users to assist with impaired gait poses several challenges, such as allowing the user to adopt a variety of gaits and the process for evaluating the efficacy and performance of these assistive devices. Here, I discuss some of the challenges in the development of assistive devices and the use of biomechanical concepts and tools for control and test validation. Several potential solutions are proposed through the case study of one project that aimed to provide gait assistance for individuals with a spinal cord injury. Further challenges and future directions are discussed, with emphasis that diverse perspectives and approaches in gait assistance will accelerate engineering solutions towards regaining mobility.

Review of control strategies for lower-limb exoskeletons to assist gait

Background

Many lower-limb exoskeletons have been developed to assist gait, exhibiting a large range of control methods. The goal of this paper is to review and classify these control strategies, that determine how these devices interact with the user.

Methods

In addition to covering the recent publications on the control of lower-limb exoskeletons for gait assistance, an effort has been made to review the controllers independently of the hardware and implementation aspects. The common 3-level structure (high, middle, and low levels) is first used to separate the continuous behavior (mid-level) from the implementation of position/torque control (low-level) and the detection of the terrain or user’s intention (high-level). Within these levels, different approaches (functional units) have been identified and combined to describe each considered controller.

Results

291 references have been considered and sorted by the proposed classification. The methods identified in the high-level are manual user input, brain interfaces, or automatic mode detection based on the terrain or user’s movements. In the mid-level, the synchronization is most often based on manual triggers by the user, discrete events (followed by state machines or time-based progression), or continuous estimations using state variables. The desired action is determined based on position/torque profiles, model-based calculations, or other custom functions of the sensory signals. In the low-level, position or torque controllers are used to carry out the desired actions. In addition to a more detailed description of these methods, the variants of implementation within each one are also compared and discussed in the paper.

Conclusions

By listing and comparing the features of the reviewed controllers, this work can help in understanding the numerous techniques found in the literature. The main identified trends are the use of pre-defined trajectories for full-mobilization and event-triggered (or adaptive-frequency-oscillator-synchronized) torque profiles for partial assistance. More recently, advanced methods to adapt the position/torque profiles online and automatically detect terrains or locomotion modes have become more common, but these are largely still limited to laboratory settings. An analysis of the possible underlying reasons of the identified trends is also carried out and opportunities for further studies are discussed.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12984-021-00906-3.

Biomechanical analysis of an unpowered hip flexion orthosis on individuals with and without multiple sclerosis

BACKGROUND

Gait impairment is a common complication of multiple sclerosis (MS). Gait limitations such as limited hip flexion, foot drop, and knee hyperextension often require external devices like crutches, canes, and orthoses. The effects of mobility-assistive technologies (MATs) prescribed to people with MS are not well understood, and current devices do not cater to the specific needs of these individuals. To address this, a passive unilateral hip flexion-assisting orthosis (HFO) was developed that uses resistance bands spanning the hip joint to redirect energy in the gait cycle. The purpose of this study was to investigate the short-term effects of the HFO on gait mechanics and muscle activation for people with and without MS. We hypothesized that (1) hip flexion would increase in the limb wearing the device, and (2) that muscle activity would increase in hip extensors, and decrease in hip flexors and plantar flexors.

METHODS

Five healthy subjects and five subjects with MS walked for minute-long sessions with the device using three different levels of band stiffness. We analyzed peak hip flexion and extension angles, lower limb joint work, and muscle activity in eight muscles on the lower limbs and trunk. Single-subjects analysis was used due to inter-subject variability.

RESULTS

For subjects with MS, the HFO caused an increase in peak hip flexion angle and a decrease in peak hip extension angle, confirming our first hypothesis. Healthy subjects showed less pronounced kinematic changes when using the device. Power generated at the hip was increased in most subjects while using the HFO. The second hypothesis was not confirmed, as muscle activity showed inconsistent results, however several subjects demonstrated increased hip extensor and trunk muscle activity with the HFO.

CONCLUSIONS

This exploratory study showed that the HFO was well-tolerated by healthy subjects and subjects with MS, and that it promoted more normative kinematics at the hip for those with MS. Future studies with longer exposure to the HFO and personalized assistance parameters are needed to understand the efficacy of the HFO for mobility assistance and rehabilitation for people with MS.

Performance Evaluation of Lower Limb Exoskeletons: A Systematic Review

Benchmarks have long been used to verify and compare the readiness level of different technologies in many application domains. In the field of wearable robots, the lack of a recognized benchmarking methodology is one important impediment that may hamper the efficient translation of research prototypes into actual products. At the same time, an exponentially growing number of research studies are addressing the problem of quantifying the performance of robotic exoskeletons, resulting in a rich and highly heterogeneous picture of methods, variables and protocols. This review aims to organize this information, and identify the most promising performance indicators that can be converted into practical benchmarks. We focus our analysis on lower limb functions, including a wide spectrum of motor skills and performance indicators. We found that, in general, the evaluation of lower limb exoskeletons is still largely focused on straight walking, with poor coverage of most of the basic motor skills that make up the activities of daily life. Our analysis also reveals a clear bias towards generic kinematics and kinetic indicators, in spite of the metrics of human-robot interaction. Based on these results, we identify and discuss a number of promising research directions that may help the community to attain a comprehensive benchmarking methodology for robot-assisted locomotion more efficiently.

Effects of an exoskeleton-assisted gait training on post-stroke lower-limb muscle coordination

Objective.Powered exoskeletons have been used to help persons with gait impairment regain some walking ability. However, little is known about its impact on neuromuscular coordination in persons with stroke. The objective of this study is to investigate how a powered exoskeleton could affect the neuromuscular coordination of persons with post-stroke hemiparesis.Approach.Eleven able-bodied subjects and ten stroke subjects participated in a single-visit treadmill walking assessment, in which their motion and lower-limb muscle activities were captured. By comparing spatiotemporal parameters, kinematics, and muscle synergy pattern between two groups, we characterized the normal gait pattern and the post-stroke motor deficits. Five eligible stroke subjects received exoskeleton-assisted gait trainings and walking assessments were conducted pre-intervention (Pre) and post-intervention (Post), without (WO) and with (WT) the exoskeleton. We compared their gait performance between (a) Pre and Post to investigate the effect of exoskeleton-assisted gait training and, (b) WO and WT the exoskeleton to investigate the effect of exoskeleton wearing on stroke subjects.Main results.While four distinct motor modules were needed to describe lower-extremity activities during stead-speed walking among able-bodied subjects, three modules were sufficient for the paretic leg from the stroke subjects. Muscle coordination complexity, module composition and activation timing were preserved after the training, indicating the intervention did not significantly change the neuromuscular coordination. In contrast, walking WT the exoskeleton altered the stroke subjects' synergy pattern, especially on the paretic side. The changes were dominated by the activation profile modulation towards the normal pattern observed from the able-bodied group.Significance.This study gave us some critical insight into how a powered exoskeleton affects the stroke subjects' neuromuscular coordination during gait and demonstrated the potential to use muscle synergy as a method to evaluate the effect of the exoskeleton training.This study was registered at ClinicalTrials.gov (identifier: NCT03057652).

Biomechanical Comparison of Assistance Strategies Using a Bilateral Robotic Knee Exoskeleton

Despite there being studies that have investigated the effects of human augmentation using a knee exoskeleton, comparing different assistance schemes on a single knee exoskeleton has not been studied. Using a light-weight, low-profile bilateral knee exoskeleton system, this study examined and compared the biomechanical effects of three common assistance strategies (biological torque, impedance, and proportional myoelectric controllers) exhibiting different levels of flexibility for the user to control the assistance. Nine subjects walked on a 15% gradient incline surface at 1.1 m/s in the three powered conditions and with the exoskeleton unpowered. All the assistance strategies significantly reduced the metabolic cost of the users compared to the unpowered condition by 3.0% on average across strategies (p < 0.05), led by the significant reduction in the biological knee kinetic effort and knee extensor muscle activation (p < 0.05). Between assistance strategies, the metabolic cost and biomechanics displayed no statistically significant differences. The metabolic and biomechanical results indicate that powered extension assistance during early stance can improve performance compared to the unpowered condition. However, the user's ability to control the assistance may not be significant for human augmentation when walking on an inclined surface with a knee exoskeleton.

Locomotion Mode Recognition with Inertial Signals for Hip Joint Exoskeleton

Recognizing locomotion modes is a crucial step in controlling lower-limb exoskeletons/orthoses. Our study proposed a fuzzy-logic-based locomotion mode/transition recognition approach that uses the onrobot inertial sensors for a hip joint exoskeleton (active pelvic orthosis). The method outputs the recognition decisions at each extreme point of the hip joint angles purely relying on the integrated inertial sensors. Compared with the related studies, our approach enables calibrations and recognition without additional sensors on the feet. We validated the method by measuring four locomotion modes and eight locomotion transitions on three able-bodied subjects wearing an active pelvic orthosis (APO). The average recognition accuracy was 92.46% for intrasubject crossvalidation and 93.16% for intersubject crossvalidation. The average time delay during the transitions was 1897.9 ms (28.95% one gait cycle). The results were at the same level as the related studies. On the other side, the study is limited in the small sample size of the subjects, and the results are preliminary. Future efforts will be paid on more extensive evaluations in practical applications.

Design and First Operation of an Active Lower Limb Exoskeleton with Parallel Elastic Actuation

The lower limb exoskeleton investigated in this work actively supports the knee and hip and is intended to provide full motion support during gait. Parallel elastic actuators are integrated into the hip joints to improve the energy efficiency in gait. The prototype was tested in sit-to-stand and gait trials, in which the actuators were cascade-controlled with position trajectories. The compliant actuation of the hip in gait experiments proved to be more efficient; the peak torque was reduced by up to 31% and the RMS power was reduced by up to 36%.

Modeling and Simulation of a Human Knee Exoskeleton's Assistive Strategies and Interaction

Exoskeletons are increasingly used in rehabilitation and daily life in patients with motor disorders after neurological injuries. In this paper, a realistic human knee exoskeleton model based on a physical system was generated, a human-machine system was created in a musculoskeletal modeling software, and human-machine interactions based on different assistive strategies were simulated. The developed human-machine system makes it possible to compute torques, muscle impulse, contact forces, and interactive forces involved in simulated movements. Assistive strategies modeled as a rotational actuator, a simple pendulum model, and a damped pendulum model were applied to the knee exoskeleton during simulated normal and fast gait. We found that the rotational actuator-based assistive controller could reduce the user's required physiological knee extensor torque and muscle impulse by a small amount, which suggests that joint rotational direction should be considered when developing an assistive strategy. Compared to the simple pendulum model, the damped pendulum model based controller made little difference during swing, but further decreased the user's required knee flexor torque during late stance. The trade-off that we identified between interaction forces and physiological torque, of which muscle impulse is the main contributor, should be considered when designing controllers for a physical exoskeleton system. Detailed information at joint and muscle levels provided in this human-machine system can contribute to the controller design optimization of assistive exoskeletons for rehabilitation and movement assistance.

Robot-Aided Training of Propulsion During Walking: Effects of Torque Pulses Applied to the Hip and Knee Joints During Stance

We sought to evaluate the effects of the application of torque pulses to the hip and knee joint via a robotic exoskeleton in the context of training propulsion during walking. Based on our previous study, we formulated a set of conditions of torque pulses applied to the hip and knee joint associated with changes in push-off posture, a component of propulsion. In this work, we quantified the effects of hip/knee torque pulses on metrics of propulsion, specifically hip extension (HE) and normalized propulsive impulse (NPI), in two experiments. In the first experiment, we exposed 16 participants to sixteen conditions of torque pulses during single strides to observe the immediate effects of pulse application. In the second experiment, we exposed 16 participants to a subset of those conditions for 200 strides to quantify short-term adaptation effects. During pulse application, NPI aligned with the expected modulation of push-off posture, while HE was modulated in the opposite direction. The timing of the applied pulses, early or late stance, was crucial, as the effects were often in the opposite direction when changing timing condition. Extension torque applied at late stance increased HE in both experiments - range of change in HE: (2.9 ± 0.4 deg, 7.7 ± 1.0 deg), . The same conditions resulted in a negative change in NPI only in the single pulse experiment - change in NPI for knee torque: -3.0 ± 0.4 ms, - and no significant change for hip torque. Also, knee extension and flexion torque during early and late stance, respectively, increased NPI during single pulse application - range of change in NPI: (3.8, 4.6) ± 0.8 ms, . During repeated pulse application, NPI increased for late stance flexion torque - range of change in NPI: (4.5 ± 0.7 ms, 4.8 ± 0.8 ms), , but not late stance extension torque. After exposure, we observed positive after-effects in HE in three conditions - range of change in HE: (2.0 ± 0.3 deg, 3.7 ± 0.7 deg) - and significant positive after-effects in NPI for early stance flexion torques - change in NPI: (2.7 ± 0.6 ms, ). These results indicate that positive propulsive after-effects can be achieved through repeated exposure to torque pulses.

Biological Hip Torque Estimation using a Robotic Hip Exoskeleton

Machine learning (ML) algorithms present an opportunity to estimate joint kinetics using a limited set of mechanical sensors. These estimates could be used as a continuous reference signal for exoskeleton control, able to modulate exoskeleton assistance in real-world environments. In this study, sagittal plane biological hip torque during level ground, incline and decline walking was calculated using inverse dynamics of human subject data. Subsequently, this torque was estimated using neural network (NN) and XGBoost ML models. Model inputs consisted solely of mechanical sensor data onboard a robotic hip exoskeleton. These results were compared to a baseline method of estimating hip torque as the mean torque profile during ambulation. On average across conditions, the NN and XGBoost models estimated biological hip torque with an RMSE of 0.116±0.015 and 0.108±0.011 Nm/kg, respectively, which was significantly less than the baseline estimation that had an RMSE of 0.300±0.145 Nm/kg (p<0.05). Fitting the baseline method to ambulation mode specific data significantly reduced overall RMSE by 59.3%; however, the ML models were still significantly better than the baseline method (p<0.05). These results show that machine learning algorithms can estimate biological hip torque using only mechanical sensors onboard a hip exoskeleton better than simply using an average torque profile. This suggests that these estimation models could be suitable for modulating exoskeleton assistance. Additionally, no evidence suggested the need to train separate ML models for each ambulation mode as estimation RMSE was not significantly different across unified and separated ML models.

A Computational Internal Model to Quantify the Effect of Sensorimotor Augmentation on Motor Output

The aging process, as well as neurological disorders, causes a decline in sensorimotor functions, which can often bring degraded motor output. As a means of compensation for such sensorimotor deficiencies, sensorimotor augmentation has been actively investigated. Consequently, exoskeleton devices or functional electrical stimulation could augment the muscle activity, while textured surfaces or electrical nerve stimulations could augment the sensory feedback. However, it is not easy to precisely anticipate the effects of specific augmentation because sensory feedback and motor output interact with each other as a closed-loop operation via the central and peripheral nervous systems. A computational internal model can play a crucial role in anticipating such an effect of augmentation therapy on the motor outcome. Still, no existing internal sensorimotor loop model has been represented in a complete computational form facilitating the anticipation. This paper presents such a computational internal model, including numerical values representing the effect of sensorimotor augmentation. With the existing experimental results, the model performance was evaluated indirectly. The change of sensory gain affects motor output inversely, while the change of motor gain did not change or minimally affects the motor output.Clinical Relevance- The presented computational internal model will provide a simple and easy tool for clinicians to design therapeutic intervention using sensorimotor augmentation.

Iterative Learning Control for a Soft Exoskeleton with Hip and Knee Joint Assistance

Walking on different terrains leads to different biomechanics, which motivates the development of exoskeletons for assisting on walking according to the type of a terrain. The design of a lightweight soft exoskeleton that simultaneously assists multiple joints in the lower limb is presented in this paper. It is used to assist both hip and knee joints in a single system, the assistance force is directly applied to the hip joint flexion and the knee joint extension, while indirectly to the hip extension also. Based on the biological torque of human walking at three different slopes, a novel strategy is developed to improve the performance of assistance. A parameter optimal iterative learning control (POILC) method is introduced to reduce the error generated due to the difference between the wearing position and the biological features of the different wearers. In order to obtain the metabolic rate, three subjects walked on a treadmill, for 10 min on each terrain, at a speed of 4 km/h under both conditions of wearing and not wearing the soft exoskeleton. Results showed that the metabolic rate was decreased with the increasing slope of the terrain. The reductions in the net metabolic rate in the experiments on the downhill, flat ground, and uphill were, respectively, 9.86%, 12.48%, and 22.08% compared to the condition of not wearing the soft exoskeleton, where their corresponding absolute values were 0.28 W/kg, 0.72 W/kg, and 1.60 W/kg.

Quasi-Direct Drive Actuation for a Lightweight Hip Exoskeleton with High Backdrivability and High Bandwidth

High-performance actuators are crucial to enable mechanical versatility of wearable robots, which are required to be lightweight, highly backdrivable, and with high bandwidth. State-of-the-art actuators, e.g., series elastic actuators (SEAs), have to compromise bandwidth to improve compliance (i.e., backdrivability). We describe the design and human-robot interaction modeling of a portable hip exoskeleton based on our custom quasi-direct drive (QDD) actuation (i.e., a high torque density motor with low ratio gear). We also present a model-based performance benchmark comparison of representative actuators in terms of torque capability, control bandwidth, backdrivability, and force tracking accuracy. This paper aims to corroborate the underlying philosophy of "design for control", namely meticulous robot design can simplify control algorithms while ensuring high performance. Following this idea, we create a lightweight bilateral hip exoskeleton to reduce joint loadings during normal activities, including walking and squatting. Experiments indicate that the exoskeleton is able to produce high nominal torque (17.5 Nm), high backdrivability (0.4 Nm backdrive torque), high bandwidth (62.4 Hz), and high control accuracy (1.09 Nm root mean square tracking error, 5.4% of the desired peak torque). Its controller is versatile to assist walking at different speeds and squatting. This work demonstrates performance improvement compared with state-of-the-art exoskeletons.

Effects of Assistance During Early Stance Phase Using a Robotic Knee Orthosis on Energetics, Muscle Activity, and Joint Mechanics During Incline and Decline Walking

The knee joint performs a significant amount of positive or negative mechanical work during gradient walking, and targeted assistance during periods of high mechanical work could yield strong human augmentation benefits. This paper explores the biomechanical effects of providing knee extension assistance during the early stance phase of the gait cycle using a powered unilateral knee exoskeleton during gradient walking on able-bodied subjects. Twelve subjects walked on 15% gradient incline and decline surfaces with the exoskeleton providing knee extension assistance during the early stance phase of the gait cycle. For both incline and decline walking, the exoskeleton assistance reduced the muscle activation of the knee extensors on the assisted leg ( ). However, only approximately half the individuals responded to exoskeleton assistance positively by reducing their metabolic cost of walking for both incline and decline tasks. The results indicate that, unlike the individuals who did respond, the individuals who did not respond to the assistance may have penalized their metabolic cost by their biomechanical compensatory behaviors from the unassisted leg.

ExoProsthetics: Assisting Above-Knee Amputees with a Lightweight Powered Hip Exoskeleton

In this paper, we explore the effect of residual hip assistance in one above-knee amputee subject using a novel lightweight powered hip exoskeleton. Differently from a powered prosthesis, a powered hip exoskeleton adds mass proximally. Thus, we expect that the negative effect of the added mass will be lower for a powered hip exoskeleton than a powered ankle and knee prosthesis. Consequently, residual-hip assistance may more easily lead to a net reduction of metabolic effort. To preliminarily assess this hypothesis, we measured the physiological cost index (PCI) while an above-knee subject walked with and without a powered hip exoskeleton. Experimental results show 20.5% reduction of PCI when walking with the powered hip exoskeleton.

Biomechanical effects of passive hip springs during walking

Passive spring-like structures can store and return energy during cyclic movements and thereby reduce the energetic cost of locomotion. That makes them important components of the human body and wearable assistive devices alike. This study investigates how springs placed anteriorly across the hip joint affect leg joint angles and powers, and leg muscle activities during level walking at 0.5 to 2.1 m/s. We hypothesized that the anterior hip springs (I) load hip extension, (II) support hip flexion and (III) affect ankle muscle activity and dynamics during walking. Effects at the ankle were expected because hip and ankle redistribute segmental power in concert to achieve forward progression. We observed that the participants' contribution to hip power did not increase during hip extension as the spring stored energy. Simultaneously, the activities of plantarflexor muscles that modulate energy storage in the Achilles tendon were reduced by 28% (gastrocnemius medialis) and 9% (soleus). As the spring returned energy with the onset of hip flexion, the participants' contribution to hip power was reduced by as much as 23%. Soleus activity before push-off increased by up to 9%. Instead of loading hip extension, anterior hip springs seem to store and return parts of the energy normally exchanged with the Achilles tendon. Thereby, the springs support hip flexion but may reduce elastic energy storage in and hence recoil from the Achilles tendon. This interaction should be considered during the design and simulation of wearable assistive devices as it might - depending on user characteristics - enhance or diminish their overall functionality.

Overview: Types of Lower Limb Exoskeletons

Researchers have given attention to lower limb exoskeletons in recent years. Lower limb exoskeletons have been designed, prototype tested through experiments, and even produced. In general, lower limb exoskeletons have two different objectives: (1) rehabilitation and (2) assisting human work activities. Referring to these objectives, researchers have iteratively improved lower limb exoskeleton designs, especially in the location of actuators. Some of these devices use actuators, particularly on hips, ankles or knees of the users. Additionally, other devices employ a combination of actuators on multiple joints. In order to provide information about which actuator location is more suitable; a review study on the design of actuator locations is presented in this paper. The location of actuators is an important factor because it is related to the analysis of the design and the control system. This factor affects the entire lower limb exoskeleton’s performance and functionality. In addition, the disadvantages of several types of lower limb exoskeletons in terms of actuator locations and the challenges of the lower limb exoskeleton in the future are also presented in this paper.

Effect of Common Pavements on Interjoint Coordination of Walking with and without Robotic Exoskeleton

Background

The analysis and comprehension of the coordination control of a human gait on common grounds benefit the development of robotic exoskeleton for motor recovery.

Objective

This study investigated whether the common grounds effect the interjoint coordination of healthy participants with/without exoskeletons in walking.

Methods

The knee-ankle coordination and hip-knee coordination of 8 healthy participants in a sagittal plane were measured on five kinds of pavements (tiled, carpet, wooden, concrete, and pebbled) with/without exoskeletons, using the continuous relative phase (CRP). The root mean square of CRP (CRP_RMS) over each phase of the gait cycle is used to analyze the magnitude of dephasing between joints, and the standard deviation of CRP (CRP_SD) in the full gait cycle is used to assess the variability of coordination patterns between joints.

Results

The CRP_Hip-Knee/RMS of the carpet pavement with exoskeleton is different from that of other pavements (except the tiled pavement) in the midstance phase. The CRP_Hip-Knee/RMS on the pebble pavement without exoskeleton is less than that on the other pavements in all phases. The CRP_Hip-Knee/SD of the pebble pavement without exoskeleton is smaller than that of other pavements. The CRP_{Knee-Ankle/SD} with/without exoskeleton is similar across all pavements.

Conclusion

The compressive capacity of the pavement and the unevenness of the pavement are important factors that influence interjoint coordination, which can be used as key control elements of gait to adapt different pavements for robotic exoskeleton.

Novelty

We provide a basis of parameter change of kinematics on different common grounds for the design and optimization of robotic exoskeleton for motor recovery.

State-of-the-art research in robotic hip exoskeletons: A general review

Ageing population is now a global challenge, where physical deterioration is the common feature in elderly people. In addition, the diseases, such as spinal cord injury, stroke, and injury, could cause a partial or total loss of the ability of human locomotion. Thus, assistance is necessary for them to perform safe activities of daily living. Robotic hip exoskeletons are able to support ambulatory functions in elderly people and provide rehabilitation for the patients with gait impairments. They can also augment human performance during normal walking, loaded walking, and manual handling of heavy-duty tasks by providing assistive force/torque. In this article, a systematic review of robotic hip exoskeletons is presented, where biomechanics of the human hip joint, pathological gait pattern, and common approaches to the design of robotic hip exoskeletons are described. Finally, limitations of the available robotic hip exoskeletons and their possible future directions are discussed, which could serve a useful reference for the engineers and researchers to develop robotic hip exoskeletons with practical and plausible applications in geriatric orthopaedics.

The translational potential of this article

The past decade has witnessed a remarkable progress in research and development of robotic hip exoskeletons. Our aim is to summarize recent developments of robotic hip exoskeletons for the engineers, clinician scientists and rehabilitation personnel to develop efficient robotic hip exoskeletons for practical and plausible applications.

Bio-Inspired Balance Control Assistance Can Reduce Metabolic Energy Consumption in Human Walking

The amount of research on developing exoskeletons for human gait assistance has been growing in the recent years. However, the control design of exoskeletons for assisting human walking remains unclear. This paper presents a novel bio-inspired reflex-based control for assisting human walking. In this approach, the leg force is used as a feedback signal to adjust hip compliance. The effects of modulating hip compliance on walking gait is investigated through joint kinematics, leg muscle activations and overall metabolic costs for eight healthy young subjects. Reduction in the average metabolic cost and muscle activation are achieved with fixed hip compliance. Compared to the fixed hip compliance, improved assistance as reflected in more consistent reduction in muscle activities and more natural kinematic behaviour are obtained using the leg force feedback. Furthermore, smoother motor torques and less peak power are two additional advantages obtained by compliance modulation. The results show that the proposed control method which is inspired by human posture control can not only facilitate the human gait, but also reduce the exoskeleton power consumption. This demonstrates that the proposed bio-inspired controller allows a synergistic interaction between human and robot.

Switching Assistance for Exoskeletons During Cyclic Motions

This paper proposes a novel control algorithm for torque-controlled exoskeletons assisting cyclic movements. The control strategy is based on the injection of energy parcels into the human-robot system with a timing that minimizes perturbations, i.e., when the angular momentum is maximum. Electromyographic activity of main flexor-extensor knee muscles showed that the proposed controller mostly favors extensor muscles during extension, with a statistically significant reduction in muscular activity in the range of 10–20% in 60 out of 72 trials (i.e., 83%), while no effect related to swinging speed was recorded (speed variation was lower than 10% in 92% of the trials). In the remaining cases muscular activity increment, when statistically significant, was less than 10%. These results showed that the proposed algorithm reduced muscular effort during the most energetically demanding part of the movement (the extension of the knee against gravity) without perturbing the spatio-temporal characteristics of the task and making it particularly suitable for application in exoskeleton-assisted cyclic motions.

Effects of foot pronation on the lower limb sagittal plane biomechanics during gait

BACKGROUND

Increased foot pronation may compromise ankle plantarflexion moment during the stance phase of gait, which may overload knee and hip.

RESEARCH QUESTION

This study investigated the influence of increased foot pronation on lower limbs angular displacement, internal moments and power in the sagittal plane and ground reaction force and center of pressure displacement during the stance phase of gait.

METHODS

Kinematic and kinetic data of 22 participants (10 women and 12 men) were collected while they walked wearing flat (control condition) and laterally wedged sandals to induce foot pronation (inclined condition). We used principal component analysis for data reduction and dependent t-test to compare differences between conditions with α = 0.05.

RESULTS

The inclined condition increased forefoot range of motion (p < 0.001; effect size = 0.73); increased ankle plantarflexion angle (p < 0.001; effect size = 0.96); reduced ankle plantarflexion moment in mid and terminal stance phases and delayed and increased ankle plantarflexion moment in late stance (p < 0.001; effect size = 0.72); increased range of ankle power during late stance (p = 0.006; effect size = 0.56); reduced knee range of moment (p < 0.001; effect size = 0.76); increased range of knee power in early stance and reduced knee power generation in late stance (p = 0.005; effect size = 0.56); reduced the anterior displacement of the center of pressure (p < 0.001; effect size = 0.82) and increased the ground reaction force in the anterior direction (p = 0.003; effect size = 0.60).

SIGNIFICANCE

Increased foot pronation compromises lower limb mechanics in the sagittal plane during the stance phase of gait. These findings are explained by the fact that foot pronation increases foot segments flexibility and compromises foot lever arm function during the stance of gait.